Before starting…
FCC NOTICE TO USERS:
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions.
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
IMPORTANT NOTE:
To comply with the FCC RF exposure compliance requirements, no change to the antenna or
the device is permitted. Any change to the antenna or the device could result in the device
exceeding the RF exposure requirements and void user's authority to operate the device.
During transmitter operation, in order to meet RF maximum permissible Exposure Safety
Guidelines, a minimum distance of 0cm shall be maintained between this device and
personnel.
This equipment may generate or use frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved
in the instruction manual. The user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
시작하기
1.
This user manual may be changed without notice in accordance with
전에...
improvements to the product or changes in available functions.
2.
This user manual has been prepared based on information available at the
time of publishing and may have technical or editorial errors or
3.
The screen and shape of the product in this manual may differ from that of
omissions.
the actual product.
4.
All the content of this manual is protected by Copyright Law.
5.
All the rights for the software installed on this product belong
to DOTel
Ltd. And are protected by Copyright Law.
6.
Among the content specified in this manual, some functions may not be
installed in your PDA (Wireless LAN, Bluetooth)
Co.,
Consent Regarding Copyright and Use...
1.
All the contents in this manual and PDA software are protected by Copyright
Law and all the rights belong to DOTel
2.
No part of this manual may be duplicated, renovated or translated into other
languages without prior written consent. The act of duplicating,
distributing this manual without permission is a crime punishable in
accordance with Copyright Law.
3.
As to instructions for separate business programs not specified in this
manual, and questions about and after service for such programs,please
contact the software provider.
4.
For all other applications or programs installed by the user except the basic
program, each software provider should specify contact information required
to make inquiries or ask for technical support on the product manual or on
the packaging, or enclose a separate manual with contact information.
5.
DOTel
once PDAs
Co., Ltd. Does not provide any warranty for all the software installed
are shipped out of the factory.
Co., Ltd.
correcting or
6.
DOT is a trademark of DOTel
7.
The logos and product names, Microsoft, Windows and Internet Explorer,
are trademarks of Microsoft and MS Windows CE software installedon this
device is a product officially licensed by Microsoft.
8.
All the product names and program names used in this manual and the
product are company names, symbols, trademarks or registered trademarks
of each owner.
9.
DOTel
loaded in this product on request of mobile communication providers or for
improvement or verification of the products.
Co., Ltd. May ask the application providers to provide their software
Co., Ltd. Protected by law.
Table of Contents
1.
Important Notices.
2.
Before Using
2.1 Package Contents
2.2 Button Layout and Physical Features
2.3 Connection to a PC
3.
Additional Functions
3.1 Wireless LAN
3.2 Bluetooth
4.
Problem Solving and Warranty
4.1 Problem Solving
4.2 Contacting Customer Support
4.3 Product Warranty
4.4 communication and Product Specifications
4.5 Product specifications
1. Important Notices: Proper Usage and Battery Care
Be sure to carefully read this user manual, as not observing thecautions may
cause injury of the user or other persons, or damage to property.
!!
The manufacturer and seller do not take any responsibilities for
accidents due to not observing the cautions specified in this manual.
any and all
This product should be used only for the established purpose. Do
product for other purposes than those specified in the user manual.
If there is an odor of burning or excessive heat from the product while in use,
remove the battery and immediately contact the customer service center.
Be sure to use the product in a bright place to protect your eyesight, as looking
into the LCD screen in a dark place for a long period of time may hurt your
eyesight.
We recommend you to back up important data in this product often. The seller and
manufacturer do not take any responsibility for data loss, even during service or
repair of the product. The manufacturer and seller as well as the customer service
center do not take any responsibility for data loss.
Do not place the product near magnets or magnetic fields. It may
the product.
not use the
cause failure of
Do not handle the product with wet hands as it may cause malfunction of the
product and, especially, if the AC adapter is handled with wet hands, there is a risk
of electrocution.
Use the LCD screen with a stylus pen provided by the manufacturer or a non
pointed tool. Otherwise, the LCD may be damaged.
The film attached on the LCD is a film used to protect the LCD during shipping. If
the product is used with the film on, poor touch screen functionmay occur. Be
sure to use the product after replacing the film with the LCD protection film
separately provided.
1. Important Notices: Proper Usage and Battery Care
When using USB cable and adapter be careful with the direction of connector
insertion If it is inserted incorrectly it may cause a problem with the PDA or PC.
Ensure the cable used is in good condition not having bent pins or damaged areas
along the cord.
!!
The product may not operate properly in extreme cold or heat. The proper
operating temperature is between -10℃
storing the product in a place in extreme temperatures, or moistareas. This may
cause external change or product damage. Store in a cool dry place.
In following cases, warranty service will not be provided and repairs may be
impossible:
-
If the product has been disassembled or remodeled by the user;
-
If the product has fallen into the water or stored in a moist place for
a long period of time;
~ 50℃. Be especially careful to avoid
-
If the product has been dropped from a high place or received
excessive external shock.
Charge the battery fully for at least 30 minutes or longer before using the product
for the first time. The product may not turn on before the battery is charged.
There is a risk of explosion if the battery installed is of the incorrect type. When
replacing the battery be sure to check that you are using the correct one. Dispose
of used batteries according to the instructions.
If battery not provided by the manufacturer are used, there is risk of product failure
or explosion. Keep the battery away from children or pets to prevent them from
biting or sucking the battery. Be careful to prevent metal objects from contacting
the charging terminals of the battery as it may cause fire.
Turn off the power of the product in places where use of the product is prohibited.
Especially where radio wave interference may occur such as in an
hospital. Electromagnetic waves generated by the product not harmful to a human
body may cause problems for electronic flight equipment or medical instruments.
airplane or in a
1. Important Notices: Proper Usage and Battery Care
Do not paint or attach stickers to the product, especially if those
paints or stickers contain metal ingredients. It may cause buttons not
to operate or reception problems.
!!
Do not use any power adaptor with this product except the one provided.
Provided adaptor
Model : KSAFE0500400W1UV-1 / Manufacturer : Kuantech(Shenzhen)Co. Ltd
2. Before using
2.1 Package Contents
…………………………………………………………………
Basic Components
Two Standard Batteries
Device
Micro USB Cable
Additional Components
Leather case
A/C Adapter
Cradle
Manual
Touch Film Stylus Pen
CD
Notice
Notice
The specification and components of this product may change
According to the situation of the manufacturer.
2. Before Using
2.2 Button Layout and Physical Features
……………………………………………………………….
Part Description and Function
Name Description
①LCD Touch screen on which information is displayed
②Speaker Where the sound is output
③
Buttons Function Key
④
Battery Switch Switch used to mount or remove the battery
⑤Battery Standard capacity battery
⑥
Power key Switching the product on/off by pressing and holding this key
⑦
Reset key Used to the product to reboot
⑧
Battery Charge indicator Displays the status of battery charging and complete
⑨
WLAN indicator Displays the status of WLAN links
⑩
Stylus pen holder Stylus pen holder
⑪
Cradle Insertion Hole Place to insert the cradle for charging and synchronization
2. Before Using
2.2 Button Layout and Physical Features
……………………………………………………………….
Button Functions
Button Function
Function Key1
Function Key2
Function Key3
To turn on/off the product, pressing
and holding the power key for three
seconds.
To turn on/off the LCD while the
device is on, pressing the power key.
Used to reset the product to reboot it
when a problem has occurred during
use.
2. Before Using
2.2 Button Layout and Physical Features
……………………………………………………………….
Power connection and charging
1
2
Connect an adapter to the back of the cradle.
3
Battery charging and using time
Standard Battery
Charging time About 3 hours
Standby time About 500 hours
Connect the device to the cradle.
While charging, the red LED light will be on.
When charging is complete, light will turn green.
Notice
Notice
-
The Charging time is calculated
based on using the proper
charging cradle.
-
Charge, talk and standby time
may depending on user
environment.
- Battery life will vary by user service type, environment, battery age.
- If user does not use the device, the battery will lose charge. The battery is
consumable product.
-If battery usage time decreases below standard a new battery should be purchased.
-PDA warranty is 1 year. Battery warranty is 6 months.
2. Before Using
2.3 To connect with a PC
……………………………………………………………….
To install Active Sync
In order to connect (synchronize) the
2
1
Agree with the license for Microsoft
ActiveSync. Select ‘Agree’
‘Next’
and press
PDA with a PC, Microsoft program
called ActiveSync is required. For
installation, execute ‘Install Program’
and press ‘Next’. At this time the PDA
and PC should not be connected.
3
Check the disk capacity which can be used
for installation and change the installation
4
location by pressing ‘Change’
‘Next’
Location.
if you want to install it in the default
or press
Enter ‘User Name’
and press ‘Next’
and ‘Organization’
2. Before Using
2.3 To connect with a PC
……………………………………………………………….
To install Active Sync
ActiveSync is now ready to install. Execute
Installation by pressing ‘install’
6
5
Installation of ActiveSync will be performed.
It may take several minutes depending on
the environment of the user PC.
8
7
Now, connect the PDA with the PC
Using the cradle.
Once installation of ActiveSync has been
Completed finish installation by pressing
‘Finish’
2. Before Using
2.3 To connect with a PC
……………………………………………………………….
To install Active Sync
10
‘Found New hardware wizard’
Select ‘Yes, connect whenever a device is
9
‘Generic USB Serial’
Select ‘Install at listed or specific
location’
and press ‘Next’
is found .
connected’
11
and press ‘Next’
Press ‘Next’
file by pressing ‘Browse’
after finding the driver
will start.
12
A driver adequate for PDA will be
installed.
13
When the window for compatibility
checking appears, proceed by pressing
‘Continue’
2. Before Using
2.3 To connect with a PC
……………………………………………………………….
To install Active Sync
Once the installation of the driver has been
completed. Press ‘Finish’
15
14
Installation of ActiveSync has been
completed and synchronization will start.
3. Functions
3.1 Wireless LAN
……………………………………………………………….
Wireless Manager
It can be controlled by
pressing on or off as
shown in the figure above
after selecting ‘Start’
‘Program’
the tool bar at the bottom
of Windows wallpaper.
WLAN on/off state is
maintained even after
the system is rebooted.
-> ‘WiFi’
->
from
3. Functions
3.2 Bluetooth
……………………………………………………………….
Bluetooth
Use this menu to activate or deactivate Bluetooth
function. Bluetooth function can be used only after
turning the module on by pressing ‘Bluetooth On’
button.
When Bluetooth function is not being used, the function
should be turned off by pressing ‘Bluetooth Off’
In order to extend the battery life.
Place the Bluetooth device within 10meters of this
equipment.
Press “search Device”
Press “Register”
device to be connected from among the list of devices
searched.
button
button.
button after selecting the Bluetooth
3. Functions
3.2 Bluetooth
……………………………………………………………….
Bluetooth
When the window asking to enter the pin code pop up,
enter the pin code and press “Confirm”. Each Bluetooth
device has a unique pin code which is used for
certification. Check the pin code with the manufacturer of
The Bluetooth device.
If ‘Registered Device List’
appears with a popup window
informing that connection is made,
connection is successfully achieved.
If a failure window pops up, the
steps should be taken again from
the step #1 in order.
Caution : Please refer to the manual of the Bluetooth device to be connected with
this equipment as the method to execute each Bluetooth device differs from one
device to another. Prior “Pairing”
is done for Bluetooth devices, connection can be made without being required to
pair again later.
However, if pairing information is deleted or the device list item is deleted by
repair, pairing should be done again.
Window
is required for Bluetooth devices. Once pairing
3. Functions
3.2 Bluetooth
……………………………………………………………….
Bluetooth
Press “Registered Device List”
Press ”Connect/Transmit”
before from the “Registered Device List”. A popup window will appear to inform that
the connection is made and connection status will be displayed in the status blank
of the list.
In case connection has not been made, start from the step #1 again. In order to
disconnect the device connected, press “Disconnect”
Caution : If the device has been paired before, connection can be made right away
without pairing procedure. The list of devices paired before will be shown in the
“Registered Device List”.
button.
button after selecting the item which has been connected
button.
3. Functions
3.2 Bluetooth
……………………………………………………………….
Bluetooth
The Device Information screen shown information
about Bluetooth device such as device name,
device ID (BD address), support profile, Bluetooth
version, firmware version and software version.
In order to delete a device once connected, press
“Delete”
deleted. A device currently connected cannot be
deleted. Delete the list after disconnecting the
device.
* Reference : Even after the device is deleted from
button after selecting the item to be
the ‘Registered Device List’, pin code window
can popup if connection is requested by the
Bluetooth device. At this time, connection can
be made by pressing ‘Confirm’
entering the pin code
button after
4. Problem solving and Warranty
4.1 Problem solving
…………………………………………………………………
Problem solving
1.
Check followings first when a problem occurs while using the product.
If the problem is still not solved, first contact the dealer you
2.
In case of the delayed response, you can reach the manufacturer.
DOTel’s
Customer service Phone No. : +82-2-850-3243
bought from.
Problem
Product does not turn on.
No sound from the speaker.
Screen is dark.
Solution
1.
When the product is shipped
from the factory, the circuitry is
disconnected. Press the power
button for 2 seconds or longer,
when the product will turn on.
2.
Check if the battery is fully
charged and charge the battery
before using the product.
1.
Check if the volume of the
product is not set at 0.
1.
Enter into ‘Setup’
the lighting.
and adjust
Some points in manual are
unclear.
1.
Use customer support in the
Web site or contact customer
center over phone, and a
customer support agent will be
glade to help you.
4. Problem Solving and Warranty
4.1 Problem solving
…………………………………………………………………
Problem
The product seems to be hot.
The PC does not recognize the
product.
Solution
1.
This product is designed to
properly radiate the heat
generated inside the product
through the case.
2.
If the product is used for a long
period of time or the adapter is
connected for long, you may
feel warmth from the case
please use the product at ease
as there is no problem with the
product.
1.
If the connection is frequently
cut and instable, please
connect the product not to a
separate hub but directly to the
USB terminal of the PC.
4. Problem Solving and Warranty
4.2 Customer support information
…………………………………………………………………
Contacting the customer service center
1.1.Contacting the customer service center
1) Web site
-
Before contacting customer support you may wish to try to find troubleshooting help
at our website : www.dotel.co.kr
-
Click ‘Contact’
-
Fill in the form and click the ‘submit’
2) Content of service
Free or charged repair of all the models of PDA and sale of various accessories.
on the DOT website.
button.
2. Before asking for repair
2. Before asking for repair
1) Be sure to check the content of ‘Problem solving’
asking for repair.
2) Do not forget to backup important data contained in the product in advance. Data
may be deleted during repair due to memory formatting, etc. The Company does not
take any responsibility for the data lost during servicing.
3) Be sure to write your telephone number and address. If there is no contact
information for the customer, a problem may occur in the process.
3. Quality Assurance
3. Quality Assurance
1) The warranty of the product is on the overleaf of the manual.
2) The products manufactured and sold by the Company are products shipped after
going through strict quality control and inspection of DOTel
in the previous pages before
Co., Ltd
4. Problem solving and Warranty
4.2 Contacting Customer Support
…………………………………………………………………
3) Warranty period
-
Main body : 1 year
-
Accessories (consumables) : 6 months (battery and items excluding the main body)
-
Mandatory period to keep spare parts in stock : 3 years from the date of releasing the
relevant model.
4) Content of warranty
When a problem occurs during normal use within the warranty period, the customer
service center of the dealer shall provide legitimate material and immaterial service in
accordance with Consumer Damage Compensation Regulation by item.
cases, repair may be inevitably impossible even within the warranty period and at a cost.
a. if the product is out of order due to shock or water-logging caused by a mistake of
the consumer,
In the following
b. if the product has been disassembled or remodeled;
c. if the product is out of order due to natural disaster such as fire, earthquake or flood;
or
d. if the product has been repaired by persons other than the designated service staff
of DOTel. Co., Ltd. , or in a non-designated service location
Individual matters not specified in this article shall be reviewed from the aspect of the
internal regulation of DOTel
at convenience of the final consumer.
5) Warranty area : Korea
4. Expense for repair
4. Expense for repair
1) If the product has failed due to defect of the product it self within the warranty period,
it will be repaired at free of charge in accordance with the warranty standard of the
Company and Consumer Damage Compensation Regulation.
2)The repair expense shall be decided in accordance with the repair price for each item
in the internal regulation of the Company.
3) Even within the warranty period, if it falls under article 3-4 above, a certain amount of
repair expense will be charged. Please understand as repair may not be possible in
some cases.
Co., Ltd. For after service and customer support but aiming
-
Hardware manufacturer : DOTel
Co., Ltd. www.dotel.co.kr
4. Problem Solving and Warranty
4.3 Product Warranty
………………………………………………………………….
Product Warranty
Classification Content
Model name DOTH-500
Date of purchase
Purchased from
Manufacturing No.
Warranty period One year from the date of purchase
Repair charge regulation
Product failure type
If the failure occurs within 10 days after the
purchase
When failure has occurred more
Repair
able
Not
repair
able
than 3times due to same defect
When failure has occurred more
than 4times due to same defect
If repair is impossible within one
month
If repair is impossible due to
unavailability of repair part
If replacement is impossible Refund
Within warranty
period
Replace N/A
Free repair Repair at a cost
Replace Repair at a cost
Replace
Replace
After warranty
period
Replace after
deducting a fixed
amount of
depreciation
Replace after
deducting a fixed
amount of
depreciation
Refund the
amount after
deducting a fixed
amount of
depreciation and
adding 10 percent
Note
This device use already certified module (TX Module FCC ID: TWG-SDCMSD30AG)
The TX module was certified with both 2.4G and 5G bands but this device only uses 802.11 b/g mode of 2.4G
band and the TX module is limited to operated 2.4G b/g mode only.
Classification Content
Frequency used:
WLAN
- 802.11b/g: 2412 ~ 2462 MHz
Modulation
- BPSK / QPSK/C
CK/ 16- QAM/ 64-QAM
Frequency used: 2402 ~ 2480 MHz
Bluetooth
Modulation : GFSK
4. Problem solving and Warranty
4.5 Product Specifications
………………………………………………………………….
Product Specifications
Classification Content
C P U ARM 11 / 800MHz
O S Windows CE5.0
R A M 128MB
R O M 256MB
DISPLAY
INTERFACE USB 2.0 (Micro USB)
BATTERY Standard type : 2800mAh
SIZE 149(L)*86(W)*17.9(H)mm
WEIGHT 200g
ADAPTER 5V/4A
TFT LCD MODULE 5.01INCH,262K
COLOR with Touch screen panel
Loading...