Dorma KTC-2, MS9 Software Update Manual

KTC-2 (MS9)

Software-Update Version 1.0.10 manual

In order to keep your door systems updated, please proceed with the following
changes.

1. Exchange CPU -Z1 (E60-0228-10) by the new one you already received.

Front view

Relay K3-K7 Terminal block –X101/-X100

Microcell Three control
unit
(N60-0685)

Module for locking device
(E60-0120)

Output module
(E60-0119)

Input module
(E60-0118)

CPU –Z1 (E60-0228-10)

Stand 08.02.2012 Technische Änderungen vorbehalten

Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 1 von 14

KTC-2 (MS9)

Rear view

Frequency converter
(N60-0402)

Mains filter (N60-0405)

Mains connection
230 V AC –X103

24 V DC power supply unit
(N60-0583)

Relay K1
(N60-0560)

Service power outlet
max. 300 W
(N60-0694)

Collector (230VAC)-X105

Potentiometer for
24V DC adjustment

Readout the parameter settings before exchanging, in order to transfer these to the
new CPU.

Stand 08.02.2012 Technische Änderungen vorbehalten

Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 2 von 14

KTC-2 (MS9)

The following chart shows the setting entries:
The standard values are shown here, they may however vary.

Parameters

Parameter
designation

Current error
status

Door diameter

#el. locking
devices

Hold after stop

#X-Pos Auto
1 - 2

SlowStop canopy

SlowStop wing

Hold after stop

Sec. area stop

Summer
configuration

Starting position
Summer

PosV after safety
stop

A/M lighting

FUT warm air
curtain

Symbo

Description Unit Range Original

l

Error list - - - - -

Door diameter mm 2000 .. 6500 (system

Electromechanical bolt locking
device no = 0, yes = 1

Time until the el. brake is
released after an Emergency
Stop
0 = brake never released, 1 - 9
= after... sec.
Number of starting positions in
Automatic 1 or 2

SlowStop time of canopy­integrated sensors

SlowStop time of wing sensor 0.1

Time until the door starts after a
safety stop

Detection range of canopy­integrated sensor in security
area for SlowStop
Starting-positions: 0°/180° (system

Starting-positions: 90°/270° [0],
60°/240° [1]

Time system operates in
positioning speed after leaving
the stationary position following
a safety stop
Automatic/manual lighting
control

Follow-up time of warm air
curtain

0 .. 1 0 U U - C -

sec (0 .. 9) sec 1 U U - C -

2 .. 5 2 U U - C -

sec (0 .. 15) sec

16 = ∞

(0 .. 15.9) sec

sec

16.0 = ∞

0.1

(0 .. 9.9) sec 1.0 U U - C -

sec

mm (d * (pi/3)

.. 500) mm

0 .. 1 0 U U - C -

0.1

(0.0 .. 2.9) sec 1.0 U U - C -

sec

0 ... 1 0 (auto) U U - C -

sec 0 ... 600 10 U U - C -

setting

- - C - -

learns
diameter)

16 U U - C -

16.0 U U - C -

700 U U - C -

- - - - U

reads X­positions)

Palm

Central system

Learning cycle

Original setting

Caption:

U = adjustable value
C = resettable value

- = non-adjustable value

Stand 08.02.2012 Technische Änderungen vorbehalten

Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 3 von 14

Wiring

KTC-2 (MS9)

2. Reconnect NC at OUT4 to NO at the locking module „IL1“.

OLD:

-Z1

Stand 08.02.2012 Technische Änderungen vorbehalten

Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 4 von 14

KTC-2 (MS9)

NEW:

-Z1

Stand 08.02.2012 Technische Änderungen vorbehalten

Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 5 von 14

KTC-2 (MS9)

3. Please check if terminals X101:59 and 60 are connected to -IL1(see picture).

-

+

For doors with integrated sliding doors bridge –X101:+ with 60, please!

Stand 08.02.2012 Technische Änderungen vorbehalten

Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 6 von 14

KTC-2 (MS9)

4. Change the following in the UPS monitoring circuit:

- New terminal strips –X105

- Additional relay K7 (230VAC-version)

Exchange the old terminal strip –X105 by the new one and install the additional relay
K7. Wiring as follows:

NEW “K7”

Stand 08.02.2012 Technische Änderungen vorbehalten

Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 7 von 14

KTC-2 (MS9)

Stand 08.02.2012 Technische Änderungen vorbehalten

Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 8 von 14

KTC-2 (MS9)

5. Carry out the wiring as follows if the door system is furnished with UPS:

If a UPS is joined up in circuit, put the inlet connector for non-heating apparatus from
–X103 into the UPS and the other 230VAC adapter cable to be connected between
UPS and control system at –X103.

Stand 08.02.2012 Technische Änderungen vorbehalten

Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 9 von 14

KTC-2 (MS9)

6. Is the door system without UPS, please proceed with the wiring as follows:

Stand 08.02.2012 Technische Änderungen vorbehalten

Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 10 von 14

KTC-2 (MS9)

7. Re-wire the inputs in the rotating part „I1“ here IN10+11 as follows:

+

-

Stand 08.02.2012 Technische Änderungen vorbehalten

Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 11 von 14

KTC-2 (MS9)

8. Adjust the crossover cable from the MS9 control system to ES200.
Connect the delivered 2-wire cable „33.1 ES200-Not Halt“ with the terminals –

X101:33/34 and ES200:32/33. Remove bridge (ES200: 32-33) at ES200 beforehand.

New connection Terminal “47” is connected to
+24VDC

Stand 08.02.2012 Technische Änderungen vorbehalten

Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 12 von 14

KTC-2 (MS9)

9. Change of emergency-stop logic. The ES200 drive will be stopped by
emergency-stop when activated.

The auxiliary contactor N60-0460 must be put on „K1“ contactor.

Normally open K1:53 and 54 to be connected to the terminals –X101:33 and 34 as
follows:

-X101

ES200

Stand 08.02.2012 Technische Änderungen vorbehalten

Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 13 von 14

KTC-2 (MS9)

If all changes are carried out, please put the door system back into operation as
follows:

10. Initial operation of the door system

 The emergency-stop is activated
 The control system is switched on
 Program switch KT on Automatic 1
 The curved sliding door wings and the showcase doors are closed
 The frequency converter and the CPU are parameterized
 Door system is in summer position
 Push Select push button and keep it pushed for 4 sec
 Release emergency-stop
 Learning cycle starts

Indication of learning cycle and positioning drive

During the learning cycle and positioning drive the display shows a gyro.

 Door system rotates in positioning speed
 The door system turns for min. 1 rotation
 Afterwards the door system restarts with its regular function
 Check all functions according to the original manual and/or the attached chart.

 Check if the control system has learned the correct diameter. Check via parameter

.

11. Testing of changes

- Door systems with UPS: Revolving door has to rotate in program switch position
Auto1 or Auto2 into summer position and stop there.

- Program switch position in „Summer“ and the sliding door is in operation (test all
program switch positions of the sliding door), sliding door must stop in case the
emergency-stop is activated and remain in this position as long as this is
activated.

- Check all revolving door functions again.

Done

Stand 08.02.2012 Technische Änderungen vorbehalten

Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 14 von 14