Dorcy 41-1087 User Manual
41-1087
(Model: LT-033)
READ ALL INSTRUCTION BEFORE FIRST USE
KEEP THIS MANUAL FOR REFERENCE
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
IMPORTANT!
Changes or modifications not expressly approved by the party responsible for
compliance could void the user ’s authority to operate the equipment. This equipment
has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions may cause harmful interference to radio communications. However, there
i
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Inc
• Con
• the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
antee that interference will not occur in a particular installation. If this
s no guar
rease the separation between the equipment and receiver
nect the equipment into an outlet on a circuit dierent from that to which
.
WARNING!
• DO NOT Immerse in water, drop into fire.
• DO NOT disassemble the product.
• Please charge the lantern once a month in order to keep the battery in a normal stage.
• Please handle the battery in a safe manor.
• If the lantern has been damaged, do not use. Consult your product provider.
• The USB charging cable is for indoor use only.
• Never short-circuit the terminal of the battery and the plug of the USB charging cable. It
• may cause the battery to overheat, resulting in fire or damage to the components.
• If the USB charging cable, USB plug, or lantern body is damaged
• Use only the Micro USB charging cable for charging the lantern.
• Lithium batteries in the product can easily rupture, ignite, or explode when exposed to
• high temperatures, or direct sunlight. The product should be stored and charged under
well ventilated environment. Short-circuiting a battery can also cause it to ignite or
explode. Never open a battery’s casing. Batteries contain safety devices that, protect the
cells inside from abuse. If damaged, these can cause the battery to ignite or explode.
• DO NOT
• Securely close the USB cover at the back of the lantern so that it will not be damaged
• Safely and properly dispose of the battery lantern according to your local regulations
• This lantern is
• A long period of non-use will lower the voltage of the battery due to natural self-dis
• DO NOT
• If the lantern does not serve the proper running time even though the battery is fully
charge the lantern and charge an electronic device at the same time. This will
shorten the lanterns battery life.
while water splash/rain, or the water resistance will be compromised.
when the lantern is not longer usable.
with this lantern.
charge. If the light is kept on until the power is completely gone (i.e. over discharge), it
may shorten the battery life. Even when you do not use the lantern, charge the battery
every month.
charged, the battery may have reached the end of its useful life.
NOT a toy. Children should be supervised to ensure that they do not play
charge the lantern for more than 8 hours.
DO NOT use.
Before First Use
Before the first and every use, charge the battery fully following the
instructions on “HOW TO CHARGE”. When the battery is not in use for a long
period, the runtime of the light will be shortened due to the self-discharge of
the battery.
Product Features
• The lantern has a function of High, Low, Red and O.
• Integrated wireless Bluetooth speaker connection, Bluetooth 3.0 Audio.
• Bluetooth on/o power switch
• Built in 3.7V 1600mAh lithium battery
• DC5V USB output, suitable for battery charge on electronic devices with USB
Input.
• Connect audio cable (not included) directly to AUX audio plug to play music
without Bluetooth connection.
Integrated handle with hook
Main Button
Battery Power Indicator (BPI)
USB cover
Micro-USB Charger Port
USB Output
Bluetooth “On/O” switch
Speaker
AUX audio plug
Micro USB charging cable
1
6
2
4
3
5
7
9
Specifications
Illumination
Runtime
Bluetooth Speaker Runtime
Battery Type
Operating Temperature
Operating Humidity
110 - 120 Lumens
4 - 5 hrs
(High)
40 - 50 hrs
(Low)
30 - 40 hrs
(Red)
10 - 12 hrs
3.7V 1600mAh Lithium battery
-20˚c to 45˚c
≤ 90%
10
8
FCC ID: PNXLT-033
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference recieved, including interference that may cause undesired
operation.
How To Charge
Fully charge the lantern using only the Micro USB charging cable.
1. Connect the micro USB with the USB charging cable into the lantern charging
port at the back of the lantern, and the other end of the USB charging cable
into your home power outlet (DC5V power sources). Or use a computer 5V/1A
power source. Plug the USB charging cable into the USB port.
2. Standard charging time is around 3 hours. (Depending on the life of the
battery, the charging time will vary). Be careful not to charge it for more than 8
hours. Over charge will damage the battery.
NOTE: The charging time and the operation time may vary depending on the
use environment.
Operation Instruction
To turn the lantern ON, press the main button.
Adjust the light settings (High / Low / Red) by pressing the main button.
“Low, High, Red” light switch
Status Indicator:
The battery power indicator light indicates how much battery
life remains for the model in use.
Lights Flashing - Charging
All Lights On - Fully charged 100% battery life
Three Lights On - Around 75% battery life
Two Lights On - Around 50% battery life
One Light On - Low battery> Around 25% battery life
Status
indicator
Charging 100% battery life 75% battery life 50% battery life 25% battery life
Operation with power bank function Turning the Lantern On
1. Select the suitable USB charging charger (dierent devices require dierent
charging cables for charging).
2. Put the USB cable into lantern USB output port, then put the other side of
the cable into the charging device (mobile, tablet, etc.). The device will then
start charging.
3. When the lantern is out of battery, it will stop charging.
Operation with audio function
To play the audio from the Bluetooth device, you need to pair the device with
the lantern speaker.
1. On your Bluetooth device, turn on Bluetooth and scan for devices in its
bluetooth menu.
2. Turn on the Bluetooth when powering up for the first time. The Lantern
speaker is discoverable for 2 minutes and is ready for pairing. A short sound will
indicate the Bluetooth is on.
3. The bluetooth device of this lantern is “DS-ML-903V1”. This will appear on
the device list of your Bluetooth device. Select the lantern. The Bluetooth status
will show on your Bluetooth menu after pairing is established. The lantern
speaker is ready to play music.
Note: If the Bluetooth turns o after five minutes, it has entered power saving
mode. Slide the power switch o and then turn on to wake the Bluetooth, and
try pairing your device again.
Repeat step 3.
Note: The lantern speaker operates with a single pair device mode. If you pair
the speaker with another device, the device least recently connected needs to
be un-paired with the speaker first.
Repeat steps 2 and 3 above.
Note: Connect audio cable (not included) directly to AUX audio plug to play
music without Bluetooth connection.
1
2
>
Bluetooth devices
3
Select it
ON
DS-ML-903V1
CONNECT
Bluetooth devices
Turn on Bluetooth
>
PAIRED
Bluetooth devices
SEARCHING
Bluetooth devices
for charging)
Status indicator :
25% battery life
100% battery life
75% battery life
50% battery life
Trouble Shooting
The lantern speaker doesn’t work or it won’t pair.
• Try moving your device closer.
• Is the lantern turned on and charged?
• Turn the Bluetooth o and then on to wake it.
• Is Bluetooth enabled on your device or computer?
• Try repeating the setup procedure in this guide or pair with
a dierent Bluetooth device.
• The speaker plays music from one device at a time. Un-pair the device not being
used. (Refer to your device documentation for help.) Pair a new device using the
setup procedure.
• If pairing with a computer, specify the lantern speaker as the audio out device on
the computer.
Loading...