DoorBird D101, D101S User guide [ml]
Page 1-19
Installation Manual
IP Video Door Station
D10x Series
Seite 20-39
Installationsanleitung
IP Video Türstation
D10x Serie
Page 40-58
Manuel d´installation
Interphone vidéo IP
Série D10x
Página 59-77
Manual de Instalación
Videoportero IP
Serie D10x
Pagina 78-88
Manuale di installazione
Videocitofono IP
Serie D10x
D10X
VERSION ., MIN. HW .
INSTALLATION MANUAL
Read these instructions carefully before starting to use any components.
Keep the manual so you can refer to it at a later date if required. If you hand
over the device to other persons for use, please hand over the operating
manual as well.
You can always find the most up-to-date version of the installation manual
on www.doorbird.com/support
To make things easier we use the term “device” for the product “IP Video
Door Station” and “mobile device” for a smartphone or tablet.
Liability
Every care has been taken in the preparation of this document.
Please inform Bird Home Automation GmbH of any inaccuracies or omissions.
Bird Home Automation GmbH cannot be held responsible for any technical
or typographical errors and reserves the right to make changes to the product
and manuals without prior notice. Bird Home Automation GmbH makes no
warranty of any kind with regard to the content of this document, including,
but not limited to, the implied warranties of merchantability and fitness for
a particular purpose. Bird Home Automation GmbH shall neither be liable
nor responsible for incidental or consequential damages in connection with
the furnishing, performance or use of this material. This product is only to
be used for its intended purpose.
Equipment Modifications
This equipment must be installed and used in strict accordance with the
instructions given in the user documentation. This equipment contains no
components that require service by the user. Unauthorized equipment
changes or modifications will invalidate all applicable regulatory certifications
and approvals.
Symbols used
Danger: Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Warning: Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Caution: Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
2
NOTICE
Hazard information
Notice: Indicates a situation which, if not avoided, could result
in damage to property.
Important: Indicates significant information which is essential
for the product to function correctly.
Note: Indicates useful information which helps in getting the
most out of the product.
WARNING
Mounting, installation and servicing work on electrical devices may
only be performed by a qualified eletrician. Failure to observe this
regulation could result in the risk of serious damage to health or fatal
injury due to electric shocks.
Devices with 110-240 V connection: The device may only be connected
to an easily accessible power socket outlet. The mains adapter must
be pulled out if a hazard occurs.
For power supply, only use the original plug-in mains adapter
delivered with the device or a recommended PoE-Switch/PoE-Injector
as specified in this manual.
Because of electrostatic charging, direct contact with the circuit
board can result in destruction of the device. Direct contact with the
circuit board must therefore be avoided at any time.
Observe the EN 60065 resp. EN 60950 resp. EN 62368 standard.
Do not use the device if there are signs of damage to the housing,
control elements or connecting sockets, for example, or if it
demonstrates a malfunction. If you have any doubts, please have
the device checked by an authorized expert.
Do not open the device. This voids the warranty of the device.
The device does not contain any parts that can be maintained by the
user. In the event of an error, please have the device checked by an
authorized expert.
ENGLISHENGLISH
3
WARNING
For safety, approval and licensing reasons (CE/FCC/IC etc.), unauthorized
change and/or modification of the device is not permitted.
The device is not a toy; do not allow children to play with it. Do not
leave packaging material lying around. Plastic films/bags, pieces of
polystyrene, etc. can be dangerous in the hands of a child.
Always lay cables in such a way that they do not become a risk to
people and domestic animals.
Voltage is applied to parts within the equipment. Do not touch any
parts that are not associated with the installation, wiring, or connection.
Electric shock could result.
On devices which are not marked as weather-proof: Keep the device
away from water or any other liquid.
Do not install or make any wire terminations while power supply is
plugged in. It can cause eletric shock or damage to the device.
Before turning on power, make sure wires are not crossed or shorted.
If not, fire or eletric shock could result.
High voltage may be present internally. Do not open the device.
Electric shock could result.
The device is not of explosion-proof. Do not install or use near gases
or flammable materials. Fire or explosion could result.
Do not install two power supplies in parallel to a single input. Fire or
damage to the device could result. Be sure to connect a single power
supply to the device.
Do not connect any terminal on the device to an AC power line. Fire
or electric shock could result.
Keep AC cord from being marred or crushed. If the AC cord is fractured,
fire or electric shock could result.
Do not plug or unplug with wet hands. Electric shock could result.
4
Do not put any metal or flammable material into the device.
Fire, electric shock, or device trouble could result.
Existing wiring such as chime wiring, etc. may contain high voltage
AC electricity. Damage to the device or electric shock could result.
Wiring and installation must be done by a qualified eletrician.
When mounting the device on a wall or ceiling, install the device in
a convenient location, but not where it could be jarred or bumped.
Injury could result.
On devices with ground terminals, connect to an earth ground.
Otherwise fire or malfunction could result.
On devices with plastic or real glass, do not put high pressure on
the glass. If fractured, injury could result.
On devices with LCD, if LCD is punctured, do not allow contact
with the liquid crystal inside. Injury could result. If necessary, gargle
your mouth and clean your eyes or skin with clear water for at least
15 minutes and consult your doctor.
Do not put anything on the device or cover the device with cloth,
silicone, glue, coating, separate covering etc. Fire or device issues
could result.
Do not install the device in any of the following locations. Fire, electric
shock, or device trouble could result.
- Places under direct sunlight or places near heating equipment that
varies in temperature.
- Places subject to dust, oil, chemicals, hydrogen sulfide (hot spring).
- Places subject to moisture and humidity extremes, such as bathrooms,
cellars, greenhouses, etc.
- Places where the temperature is very low, such as inside a refrigerated
area or in front of an air conditioner.
- Places subject to steam or smoke (e.g. near heating or cooking surfaces).
- Where noise generating devices such as dimmer switches or inverter
electrical appliances are closeby.
- Locations subject to frequent vibration or impact.
ENGLISHENGLISH
5
WARNING
On devices with intercom, be sure to perform a call test with low
audio volume on both intercom devices. A sudden call etc. may arrive
causing for example damage to your ear.
If the device does not operate properly, unplug the power supply.
All devices which are not marked as weather-proof are designed for
indoor use only. Do not use outdoor.
On devices which are marked weather-proof: Do not spray with
high-pressure water. Device issues could result.
We do not assume any liability for damage to property or personal
injury caused by improper use or the failure to observe the hazard
information. In such cases, any claim under warranty ceases.
For consequential damages, we assume no liability!
Safety instructions
NOTICE
The device shall be used in compliance with local laws and regulations.
Store the device in a dry and ventilated environment.
Avoid exposing the device to shocks or heavy pressure.
Do not install the device on unstable brackets, surfaces or walls.
Make sure the material is strong enough to support the weight of
the device.
Use only applicable tools when installing the device. Using excessive
force with tools could cause damage to the device.
Do not use chemicals, caustic agents, or aerosol cleaners.
Use a clean dry cloth for cleaning.
Use only accessories that comply with technical specification of the
device. These can be provided by Bird Home Automation GmbH.
Use only spare parts provided by or recommended by Bird Home
Automation GmbH.
Do not attempt to repair the device by yourself. Contact Bird Home
Automation GmbH for service matters.
6
Keep the device more than 1 m (3.3') away from microwave, radio, TV,
wireless router and any other wireless devices.
On devices with intercom or built-in speaker or built-in microphone
or signal transmission functions, keep the wires more than 30 cm (12'')
away from AC 100-240 V wiring. AC induced noise and/or device
malfunction could result.
Install the device in an area that will be accessible for future inspections,
repairs and maintenance.
If the device is used close to a cellular phone, the device may malfunction.
The device can be damaged if dropped. Handle with care.
The device turns inoperative during power failure.
On devices with intercom or built-in speaker or built-in microphone,
in areas where cellular or Radio / TV broadcasting station antennas are
closeby, the device may be affected by radio frequency interference.
On devices with LCD screen, it must be noted in advance that the LCD
panel, though manufactured with very high precision techniques,
inevitably will have a very small portion of its picture elements always lit
or not lit at all. This is not considered a device malfunction.
On devices with intercom, due to the environmental sound around
the device, it may hinder smooth communication, but this is not a
malfunction.
On devices with Username/Password, the Username/Password to
access the device is the customer's responsibility. Make sure to use
password that cannot be easily guessed by a third party.
We recommend that you change the Password on a regular basis.
We will, under no circumstances, be liable for damage that occurs due
to failures in power supply, network equipment or terminal devices;
failures due to Internet providers and cellular network providers;
failures such as disconnected lines and other losses in communication,
which makes it impossible to provide this service as well as in any way
delay this service due to any other causes outside of our responsibility;
or if an error or missing data occurs during transmission.
ENGLISHENGLISH
7
Transportation
NOTICE
Warranty Information
For information about the device warranty, see www.doorbird.com/warranty
When transporting the device, use the original packaging or
equivalent to prevent damage to the device.
COMPONENTS
Contents
1x DoorBird Video Door Station
1x Power supply unit (mains adaptor) with four country-specific adaptors
1x Cable with plug for the power supply (black, red)
1x Cable with plug and RJ45 jack for the network cable (white-orange,
orange, white-green, green)
1x Cable with plug for the network cable (white-orange, orange,
white-green, green), alternatively to the cable with plug and RJ45 jack
1x Cable with plug for the electric door opener (purple, purple)
1x Cable with plug for the electric door chime (blue, blue)
1x Cable with plug for the door-opening button (yellow, yellow)
Several crimp connectors
4x Phillips countersunk head screws for the wall mounting plate, long
4x Phillips countersunk head screws for the wall mounting plate, short
4x Dowels
1x Safety screw
1x Screwing-tool for the safety screw
1x Wall mounting plate with sealing ring (installation on wall surface)
1x Installation manual
1x Quickstart guide
8
Video door station
1 8
Night vision
2
HDTV video
Loudspeaker
3
Motion sensor
4
Stainless-Steel
5
Button
Microphone
6
Light sensor
7
ENGLISHENGLISH
backfront
9
10
1) Night vision
Extra bright infra-red LEDs, effective
during the hours of darkness
(infra-red light invisible to the
human eye, 850nm)
2) HDTV video
Ultra wide-angle hemispheric
lens, 180°
3) Loudspeaker
Large-sized and speech enhanced
broadband speaker
4) Motion sensor
180° Infrared motion sensor
for alarms
5) Stainless-Steel Button
With illuminated LED ring (at night),
also acts as Diagnostic-LED
6) Microphone
With active noise cancellation
7) Light sensor
For the night-vision mode
8) Locking positions
For the mounting plate
9) Connection terminal
For the power supply,
door chime, etc.
10) Screw opening
For the safety screw
VIDEOS
Need help with the installation? Be sure to watch our installation videos
which can be found on http://www.doorbird.com/support
Each individual step of the installation is clearly documented in the videos.
9
INSTALLATION
All steps below should be carried out carefully by a competent adult, taking
into consideration any applicable safety regulations. Should you have any
questions, please contact us or a competent specialist directly. Please ensure
that all wires used for the installation are undamaged along their entire
length and approved for this type of use.
Network speed and network components
Please ensure that the upload speed of your Internet connection is at least
0.5 Mbps. You can also carry out a speed test at any time via the DoorBird
app. The user experience is only as good as your network speed, network stability and quality of your network components, such as your Internet router
and WiFi access points or WiFi repeaters. Please also make sure that your network components are no older than two years old, have been manufactured
by a well-known manufacturer, and have the latest firmware installed.
Should these requirements not be fulfilled, it may happen, for example that
the performance of audio and video is poor or push notifications are delayed
or do not arrive on your smartphone or tablet at all.
High-speed Internet (via landline): DSL, cable or optical fibre
Network: 802.11b/g/n 2.4 GHz or Ethernet, with DHCP
STEP 1: SWITCHING OFF POWER
Switch off the power to all wires leading to the assembly location, i.e. the
door chime, electric door opener, power supply unit for the video door
station etc..
STEP 2: DISMANTLING THE EXISTING DOORBELL
Should there already be a doorbell on the exterior wall of the house, please
dismantle it.
STEP 3: DETERMINING THE ASSEMBLY LOCATION
The video door station uses an ultra wide-angle hemispheric lens so that
even when the person is a minimum distance of 50 cm (19.68 inches) away
from the video door station, a low installation height is sufficient. The lens is
therefore not mechanically adjustable. The camera lens should be located
at an altitude of at least 145 cm (57 inches). You may check this prior to the
final mounting. Press the mounting plate against the wall at the desired
installation site and mark the boreholes with a pencil. Remove the mounting
plate again. Ensure that no cables are to be found in the wall behind
the boreholes.
10
NOTICE
Do not expose the device to direct sunlight. The housing temperature
can exceed the maximum allowed temperature limit. This can result
in damage of electric and mechanic components of the device and
injuries especially when touching exterior parts of the device. White
and bright silver-colored front plates absorb less sunlight than dark
ones.
NOTICE
An image sensor must not be exposed to direct sunlight for an
extended period of time. Direct sunlight will “blind” the camera
and may permanently bleach the small color filters on the image
sensor chip.
Any defects caused by direct sunlight is not covered by warranty.
STEP 4: POWER SUPPLY
The video door station can be powered by two simple doorbell wires using
the power-supply unit (mains adaptor) supplied with it or via PoE (Power
over Ethernet) using a network cable. The video door station can alternatively
also be supplied with a DIN-rail power supply unit that you can obtain from
us directly.
The video door station does not use battery power. The use of a mains power
supply permits the transmission and display of on-demand live video at any
time and not only if a visitor has pressed the doorbell.
Power supply using the power-supply unit (mains adaptor)
Two insulated wires are required to power the video door station by plugging
it into the mains. These wires are normally already there and are freely
accessible once you have removed the previous doorbell. Only use the power
supply unit provided along with the video door station, or a DIN-rail power
supply unit that you can obtain from us separately, since this has been specially stabilized electrically and is equipped with an integrated audio interference reduction device. Other power supply units may destroy the video door
station or cause poor transmission quality. The warranty automatically expires if you use a different power supply unit. The power supply unit is plugged
into a wall socket inside your house, usually where the two wires from your
previous doorbell come out of the wall in the interior of the house.
Do not plug the power supply unit into the wall socket yet. Connect the power supply unit inside the house with the crimp connector provided and the
two wires that you would like to use to power the device.
ENGLISHENGLISH
11
Power supply via PoE (as an alternative)
To power the video door station via a PoE switch (e.g. D-Link DGS-1008P) or
PoE injector (e.g. TP-Link TL-PoE150S) in accordance with the PoE standard
IEEE 802.3af Mode A, the four wires bearing the numbers 1, 2, 3 and 6 of a
Cat.5 cable or better are to be used. A Cat.5 cable or better must be used as
network signals can only be transmitted over completely insulated, shielded
and twisted cables. If you use PoE as a source of power, the WiFi interface of
the video door station is automatically inactive, and the four wires for PoE
then simultaneously form the data link. The video door station won’t start
if your PoE Switch or PoE injector does not support the PoE Standard IEEE
802.3af Mode A (see Diagnostic-LED and Diagnostic-Sounds).
1. Disconnect the PoE switch or PoE injector from the power grid.
2. Place the network cable in the installation site of the video door station.
Do not combine the power supply from the power supply unit (mains adaptor)
with the power supply via PoE.
STEP 5: FURTHER CONNECTIONS (OPTIONAL)
If desired, connect additional wires to the installation site of the video door
station. The wires or connection options mentioned in this section are optional.
Connecting the unit to a network
You can connect the video door station to your existing
network via WiFi, or alternatively use a network cable
(Ethernet). For reasons of network stability, we principally
recommend using a network cable, as WiFi is sensitive to
interference (range, house walls acting as shields, reliability of performance, third party WiFi networks, wireless
transmitters causing interference in the area, etc.).
The video door station can be powered by PoE or using
the power supply unit provided. If you use PoE as a
source of power, the WiFi interface of the video door
station remains inactive.
Use only four wires (1, 2, 3 and 6) of a network cable that
meets the Cat.5 standard or a better one. The other four
wires of the network cable (4, 5, 7 and 8) are not required.
Connect the network cable in the house to your
Internet router or to your PoE switch or PoE injector
that is connected to your Internet router.
Be sure to use four insulated, shielded and twisted wires
of a network cable in accordance with the Cat.5 standard
or better.
12
Be sure to use
four insulated,
shielded and
twisted wires of
a network cable
in accordance
with the Cat.5
standard or
better.
6 (R-)
3 (R+)
2 (T-)
1 (T+)
Electric door openers
The video door station has a zero-potential relay contact
for a standardised electric door, gate or garage opener
(two wires). There is the possibility of switching on all
electric door openers that work at a maximum power of
1A in the voltage range of up to 24V (AC/DC). The video
door station does not provide its own power supply for
the electric door opener. This is provided through the
separate power supply of the electric door opener. You can
learn more about the installation of the power supply
from the instruction manual or technical specifications of
your door opener. Should you have any questions about
this, please contact the manufacturer of your door opener.
You can find compatible electric door opener and a sample
wiring diagram at www.doorbird.com/support
Conventional electric door chime
If someone rings your video door station, you will immediately receive a push notification with sound/vibration
on your smartphone or tablet. In addition the video door
station comes with a zero-potential relay contact for
connecting a conventional electric door chime inside
the building. The relay contact can be used to activate
the separate operating voltage of the door chime or the
door chime via its trigger input. If the operating voltage
of the door chime is activated, it should not be greater
than 24V (AC/DC). The power consumption should not
exceed 1A. The video door station does not provide its
own power supply for the door chime. This is provided
through the separate power supply of your conventional
door chime. Should you have any questions, please contact the manufacturer of your door chime. You can find
compatible door chimes and a sample wiring diagram at
www.doorbird.com/support
Conventional door opener button
If an electric door opener is connected to the video door
station, the door opener can be opened by App and also
be directly controlled via a zero-potential button to be
found in the interior of the building, i.e. a door opening
button. In addition, the door opener button is to be
connected to the connection terminal provided. Please
make sure to add no extra voltage on that contact. You
can find compatible door opener buttons and a sample
wiring diagram on www.doorbird.com/support
Two insulated
ENGLISHENGLISH
wires.
Two insulated
wires.
Two insulated
wires.
13
STEP 6: DOWELS
If the exterior wall of the house is not made of wood, you should drill four
holes 5 mm in diameter in the wall and then place the dowels provided into
the boreholes. If the exterior wall of the house is made of wood, you will
usually not require any dowels. There are special dowels for assembling the
video door station on an insulating wall, e.g. Fischer insulating dowels. Please
check with your insulating material manufacturer regarding which dowels
they recommend.
STEP 7: ATTACH THE MOUNTING PLATE
Put the wires that you would like to connect to the video door station
through the opening in the mounting plate provided. Position the mounting
plate against the exterior wall of the house and use the screws provided to
position it in the dowels or on the wall. The mounting plate for the video
door station has been designed in such a way that it can also be installed on
uneven walls, so it is not completely flat. The partially greater clearances at
the back also serve to stabilize temperature and moisture levels.
STEP 8: PREPARING THE WIRES
Remove about 5 mm of insulation material at the end of the wires that you
would like to connect to the video door station.
STEP 9: CONNECTING THE WIRES
It is possible to connect the video door station conveniently and safely via a
connection terminal with jacks on the reverse of the video door station.
The individual contacts on the connection terminal are labelled on the reverse
of the casing. Some connectors on the connection terminal may come provided
by us with cable. Please use appropriate crimp connectors or terminal strips
to connect the supplied cables with your wires. The accompanying crimp
connectors are weatherproof and are equipped with heat-shrink tubing which
can be sealed after assembly by, for example, carefully using a heat gun.
Please remove any cables on the connection terminal that you do not need.
14
T+ T- R+ R- O1 O2 C1 C2 B1 B2 V- V+
ENGLISHENGLISH
max. 0-24 V DC/AC, 1 A
max. 0-24 V DC/AC, 1A
0 V, 0A
CONNECTOR DESCRIPTION WIRE
T+
T-
R+
R-
O1
O2
White and orange network cable wire
(Number 1, Transmit Data +)
Orange network cable wire
(Number 2, Transmit Data -)
White and green network cable wire
(Number 3, Receive Data +)
Green network cable wire
(Number 6, Receive Data -)
Electric door opener
(zero potential)
Electric door opener
(zero potential)
white-orange
orange
white-green
green
purple
purple
C1 Electric door chime (zero potential) blue
C2 Electric door chime (zero potential) blue
B1 Door-opening button yellow
B2 Door-opening button yellow
V- Power supply, negative pole (-) black
V+ Power supply, positive pole (+) red
Please take care when connecting the wires. Connecting the wires the wrong
way may destroy the video door station.
15 V DC, 1A
15
STEP 10: FINAL ASSEMBLY
Mount the video door station on the mounting plate. The video door station
will click into the locking positions intended for the mounting plate. Use the
accompanying safety screw with the appropriate tool to fix the video door
station to the underside of the mounting plate.
STEP 11: ACTIVATING THE VIDEO DOOR STATION
Switch on the power to the wires leading to the assembly location again.
You can see whether you have connected the power supply properly from the
Diagnostic LED (it lights up once the power has been connected correctly
for up to five minutes and continuously in night-vision mode). The video door
station is ready for operation (booting up process, any software updates, etc.)
once it has emitted a short diagnosis sound from the integrated loudspeaker.
This may last for up to 5 minutes. Should you not hear a beep, please check
the power supply. Please also check whether you have used a wall-plug
power-supply and not PoE and whether you have connected the positive
pole and negative pole to the video door station correctly.
STEP 12: DOWNLOADING AND INSTALLING THE APP
Download the „DoorBird“ app by Bird Home Automation onto your mobile
device from the Apple app store or Google Play store. You can always find the
most up-to-date version of the App manual on www.doorbird.com/support
If you use WiFi for connecting the video door station to your Internet router,
first go to „Settings > WiFi Setup“ and follow the instructions.
If you have finished the WiFi set-up or have connected the video door station
to your Internet router by means of a network cable, go to „Settings > Add
device“ and click on the QR code icon in the „User“ field. Scan the user QR
code found on the „Digital Passport“ that accompanies the video door station.
If you have problems adding the video door station to the App please check
if the video door station is online ( www.doorbird.com/checkonline ). If the
video door station is not online, please check the WiFi or network cable
connection again.
Since Apple uses very high quality microphones, loudspeakers and digital audio
components that are perfectly in tune with one another, the voice quality with
an iPhone or iPad is usually noticeably better than with an Android smartphone
or Android tablet.
DIAGNOSTIC-LED
This LED light is only lit up for five minutes after the video door station has
been supplied with power (and continuously at night). It lights up as soon as
the video door station is supplied with power.
Illuminated: Device is powered
16
DIAGNOSTIC-SOUNDS
After around two to five minutes, the video door station emits brief diagnostic sounds after it has been connected to the power grid.
1x diagnostic sound: The video door station is connected to the Internet
2x diagnostic sounds: The video door station is able to communicate with
the router, but cannot access the Internet
3x diagnostic sounds: The video door station has no connection to the network
TECHNICAL SPECIFICATIONS
GENERAL
Power supply:
15V DC (power 110-240 V AC) or
Power over Ethernet (PoE 802.3af
Mode-A)
Connectors:
Power, electric door opener/strike,
door chime, door opener button,
network
Weather-proof:
Yes, IP65
Approvals:
CE, IC, FCC, IP65
Operating conditions:
-20 to +40°C / -4 to 104°F
Humidity 10 to 85% RH
(non condensing)
Scope of delivery:
Video Door Station, mounting plate,
power supply unit (world-wide,
110-240V), DIN-rail power supply
sold separately, screw package,
quick start guide
Warranty:
see www.doorbird.com/warranty
CURRENT SYSTEM REQUIREMENTS
System requirements:
Mobile Device: Newest iOS on
iPhone/iPad, newest Android on
Smartphone/Tablet
Internet: High-Speed Landline
Broadband Internet connection, DSL,
Cable or fiber optic, no socks or Proxy
server
Network: 802.11 b/g/n 2.4GHz or
Ethernet Network, with DHCP
Recommended installation height:
Camera lens should be at a min.
height of 145 cm (57 in)
VIDEO
Camera:
HDTV 720p, dynamic (VGA – HDTV)
Lens:
High-end ultra wide-angle hemispheric
lens 180° horizontal, 90° vertical,
straightened, IR-capable
Night-vision:
Yes, light sensor, automatic IR-cut
filter, 12 IR-LEDs
ENGLISHENGLISH
17
AUDIO
Audio components:
Speaker and microphone, echo and
noise cancellation
Audio streaming:
Two-way duplex
NETWORK
WiFi:
802.11 b/g/n 2.4 GHz
Ethernet:
Connector, PoE 802.3af Mode-A
MOTION SENSOR
Type:
Passiv infrared sensor (PIR)
Detection angle:
180°
Range:
2-8 m (79-315 in)
depends on environment
INTEGRATED WIRELESS MODULES
WiFi:
2,4GHz, internal antenna
OPTIONAL ACCESSORIES
Sold separately:
see www.doorbird.com/buy
Errors and omissions excepted.
18
LEGAL NOTES
General remarks
1. DoorBird is a registered trademark of Bird
Home Automation GmbH.
2. Apple, the Apple logo, Mac, Mac OS, Macintosh,
iPad, Multi-Touch, iOS, iPhone and iPod touch are
trademarks of Apple Inc.
3. Google, Android and Google Play are trademarks
of Google, Inc.
4. The Bluetooth® word mark and logos are registered trademarks of Bluetooth SIG, Inc.
5. All other company and product names may
be trademarks of the respective companies with
which they are associated.
6. We reserve the right to make changes to our
products in the interests of technical advancement. The products shown may also look different
from the products supplied based on ongoing
enhancement.
7. Reproducing or using texts, illustrations and
photos from this instruction manual in any media
– even if only in the form of excerpts – shall only be
permitted with our express written consent.
8. The design of this manual is subject to copyright protection. We do not accept any liability for
any errors or any erroneous content or printing
errors (even in the case of technical specifications
or within graphics and technical sketches).
9. Our products are in compliance with all technical guidelines, electrical and telecommunications
regulations applicable in Germany, the EU and
the USA.
Data privacy and data security
1. For maximum security, the device uses the same
encryption technologies as are used in online
banking. For your security, no port forwarding or
DynDNS is used either.
2. The data centre location for remote access over
the Internet by means of an App is obligatory in
the EU if the determined Internet IP-Address
location of the device is within the EU. The data
centre is operated in line with the most stringent
security standards.
3. Video, audio and any other surveillance methods
can be regulated by laws that vary from country
to country. Check the laws in your local region
before installing and using this device for surveillance purposes.
If the device is a door-, indoor station or camera:
In many countries video and voice signal may
only be transmitted once a visitor has rung the
bell (data privacy, configurable in the App).
Please carry out the mounting in such a way
that the detection range of the camera limits the
device exclusively to the immediate entrance
area.
The device may come with a visitor history and
motion sensor. You can activate/deactivate this
function if required.
If necessary, indicate the presence of the device in
a suitable place and in a suitable form.
Please observe any relevant country-specific
statutory regulations concerning the use of
surveillance components and surveillance cameras
applicable at the installation site.
Check with the property owner and your house
community if you are allowed to install and use
this product. Bird Home Automation GmbH
cannot be held responsible for any miss-use or
miss-configuration of this product, including the
unauthorized opening of a door.
Bird Home Automation cannot be held responsible
for damages caused by improper existing installations
or improper installation.
Software and operating system’s updates
(so-called „firmware updates“) are generally
automatically installed on the products of
Bird Home Automation GmbH via Internet, if
technically possible. Automatic firmware updates
keep the products‘ software up to date so that
they always work reliably, safely and efficiently.
Through further development, features can be
added, extended or slightly changed. Major
changes or limitations to existing features will
generally occur if Bird Home Automation GmbH
deems it necessary (e.g. for data protection, data
security or stability reasons, or to keep them up
to date). When a firmware update is available,
Bird Home Automation GmbH‘s servers generally
automatically distribute it to all compatible
products connected to the Internet or Bird
Home Automation GmbH‘s servers. This process
is gradual and can take several weeks. As soon
as a product receives a firmware update, the
system will be installed and will restart by itself.
Installed firmware updates cannot be undone.
Since the products and software of Bird Home
Automation GmbH are not explicitly customerspecific products, a customer cannot deny an
automatic update if the product is connected
to the Internet or to the Bird Home Automation
GmbH’s server.
Instructions for disposal
Do not dispose of the device with regular domestic
waste. Electronic equipment must be disposed
e.g. at local collection points for waste electronic
equipment in compliance with the Waste Elec trical
and Electronic Equipment Directive.
Publisher
Bird Home Automation GmbH
Uhlandstraße 165
10719 Berlin
Germany
Web: www.doorbird.com
Email: hello@doorbird.com
ENGLISHENGLISH
19
INSTALLATIONSANLEITUNG
Lesen Sie diese Anleitung sorgfältig, bevor Sie die Komponenten in Betrieb
nehmen. Bewahren Sie die Anleitung zum späteren Nachschlagen auf!
Wenn Sie das Gerät anderen Personen zur Nutzung überlassen, übergeben
Sie auch diese Bedienungsanleitung.
Die stets aktuelle Version der Installationsanleitung finden Sie unter
www.doorbird.com/de/support
Zur Vereinfachung der Begriffe verwenden wir „Gerät“ für das Produkt
„IP Video Türstation“ sowie „mobiles Endgerät“ für ein Smartphone/Tablet.
Haftung
Die Erstellung dieses Dokuments wurde sorgfältig vorbereitet. Bitte informieren Sie Bird Home Automation GmbH über etwaige Ungenauigkeiten
oder Unterlassungen. Bird Home Automation GmbH kann nicht für technische oder typografische Fehler verantwortlich gemacht werden und behält
sich das Recht vor, Änderungen an dem Produkt und den Handbüchern
ohne vorherige Ankündigung vorzunehmen. Bird Home Automation GmbH
übernimmt keinerlei Garantie in Bezug auf das in diesem Dokument enthaltene Material, einschließlich, aber nicht beschränkt auf die implizierten
Garantien der Marktgängigkeit und Eignung für einen bestimmten Zweck.
Bird Home Automation GmbH haftet nicht für Neben- oder Folgeschäden im
Zusammenhang mit der Bereitstellung, Durchführung oder Verwendung dieses
Materials. Das Gerät darf nur für den vorgesehenen Zweck verwendet werden.
Gerätemodifikationen
Dieses Gerät muss in Übereinstimmung mit den Anweisungen in der
Installationsanleitung installiert und verwendet werden. Dieses Gerät enthält keine vom Benutzer zu wartenden Komponenten. Durch unbefugte
Gerätemodifikationen oder Änderungen erlöschen alle anwendbaren
Zertifizierungen und Zulassungen.
Verwendete Symbole
Achtung: Weist auf eine gefährliche Situation hin, die, falls
nicht verhindert, zum Tod oder schweren Verletzungen führt.
Warnung: Weist auf eine gefährliche Situation hin, welche,
falls nicht verhindert, zum Tod oder schweren Verletzungen
20
führen kann.
Vorsicht: Weist auf eine gefährliche Situation hin, welche, falls
nicht verhindert, zu geringfügiger oder mäßiger Verletzung
führen kann.
NOTICE
Gefahrenhinweise
Bitte beachten: Weist auf eine gefährliche Situation hin,
welche, falls nicht verhindert, zu Sachschäden führen kann.
Wichtig: Weist auf wichtige Informationen hin, die den richtigen
Betrieb des Produkts gewährleisten.
Hinweis: Weist auf nützliche Informationen hin, die die optimale
Verwendung des Geräts unterstützen.
WARNUNG
Einbau, Montage und Servicearbeiten elektrischer Geräte dürfen
ausschließlich durch eine Elektrofachkraft erfolgen. Bei Nichtbeachten
besteht die Gefahr schwerer gesundheitlicher Schäden oder Lebens gefahr durch elektrische Stromschläge.
Geräte mit 110-240 V Anschluss: Das Gerät darf nur an eine leicht
zugängliche Netz-Steckdose angeschlossen werden. Bei Gefahr ist der
Netzstecker zu ziehen.
Benutzen Sie für die Stromversorgung des Gerätes ausschließlich das
mitgelieferte Originalnetzteil oder einen in dieser Anleitung empfohlenen
PoE-Switch/PoE-Injektor (sofern das Gerät PoE unterstützt).
Durch elektrostatische Aufladung kann bei direktem Kontakt mit der
Leiterplatte das Gerät zerstört werden. Vermeiden Sie daher ein direktes
Berühren der Leiterplatte zu jeder Zeit.
Norm EN 60065 bzw. EN 60950 bzw. EN 62368 beachten.
Verwenden Sie das Gerät nicht, wenn es von außen erkennbare Schä den z. B. am Gehäuse, an Bedienelementen oder an den Anschluss
buchsen bzw. eine Funktionsstörung aufweist. Im Zweifelsfall lassen
Sie das Gerät von einer autorisierten Fachkraft prüfen.
DEUTSCH
21
WARNUNG
Öffnen Sie das Gerät nicht. In solchen Fällen erlischt jeder Gewähr leistungsanspruch! Für Folgeschäden übernehmen wir keine Haftung!
Das Gerät enthält keine durch den Anwender zu wartenden Teile. Im
Fehlerfall lassen Sie das Gerät von einer autorisierten Fachkraft prüfen.
Aus Sicherheits-, Zulassungs- und Lizenzgründen (CE/FCC/IC etc.)
ist das eigenmächtige Umbauen und/oder Verändern des Gerätes
nicht gestattet.
Das Gerät ist kein Spielzeug! Erlauben Sie Kindern nicht damit zu spielen.
Lassen Sie das Verpackungsmaterial nicht achtlos liegen. Plastikfolien/
-tüten, Styroporteile etc. können für Kinder zu einem gefährlichen
Spielzeug werden.
Verlegen Sie Kabel stets so, dass diese keine Gefährdungen für
Menschen und Haustiere darstellen.
An Teilen im Gerät liegt Spannung an. Berühren Sie keine Teile, die
nicht mit der Installation, der Verdrahtung oder dem Anschluss ver bunden sind. Elektrische Stromschläge können die Folge sein.
Halten Sie die Geräte von Wasser oder anderen Flüssigkeiten fern, die
nicht als wetterfest gekennzeichnet sind.
Führen Sie keine Installation durch und stellen Sie keine Verbindungen
her, während die Stromversorgung eingeschaltet ist. Beschädigungen
am Gerät oder elektrische Stromschläge können die Folge sein.
Bevor Sie die Stromversorgung einschalten, stellen Sie sicher, dass die
Drähte nicht gekreuzt oder kurzgeschlossen sind. Feuer oder elektrische
Stromschläge können die Folge sein.
Hochspannung kann intern vorhanden sein. Öffnen Sie das Gerät nicht.
Elektrische Stromschläge können die Folge sein.
Das Gerät ist nicht explosionsgeschützt. Nicht in der Nähe von Gasen
oder brennbaren Materialien installieren oder verwenden. Feuer oder
Explosion können entstehen.
Installieren Sie nicht zwei Stromversorgungen parallel zu einem
einzigen Eingang. Feuer oder Beschädigung des Gerätes können
entstehen. Achten Sie darauf, nur ein einziges Netzteil an das Gerät
anzuschließen.
22
Schließen Sie keinen Anschluss am Gerät an eine Netzstromleitung an.
Feuer oder elektrische Stromschläge können die Folge sein.
Stellen Sie sicher, dass das Netzkabel nicht beschädigt oder
gequetscht ist. Wenn das Netzkabel gebrochen ist, kann es zu einem
Brand oder elektrischen Stromschlag kommen.
Nichts mit nassen Händen anstecken oder abziehen.
Elektrische Stromschläge können die Folge sein.
Führen Sie kein Metall oder brennbares Material in das Gerät.
Feuer, elektrische Stromschläge oder Gerätestörungen können
die Folge sein.
Bestehende Verdrahtungen wie Türgongverdrahtung usw. können
Hochspannungs-Wechselstrom enthalten. Schäden am Gerät oder
elektrische Stromschläge können auftreten. Die Verdrahtung und
Installation muss von einem qualifizierten Elektriker durchgeführt
werden.
Gerätemontage an Wand oder Decke: Vermeiden Sie Installationsorte,
an denen das Gerät Erschütterungen oder Stößen ausgesetzt ist.
Bei Geräten mit Erdungsklemmen muss eine Erdung angeschlossen
werden. Feuer oder Gerätestörungen können die Folge sein.
Bei Geräten mit Kunststoffglas oder Echtglas, keinen hohen Druck auf
das Glas ausüben. Bei Bruch kann es zu Verletzungen kommen.
Bei Geräten mit LCD, wenn LCD beschädigt ist, nicht mit dem Flüssig kristall in Kontakt kommen. Verletzungen können die Folge sein.
Wenn nötig, spülen Sie den Mund aus, reinigen Sie Ihre Augen oder
Haut mit klarem Wasser für mindestens 15 Minuten und wenden
Sie sich an Ihren Arzt.
Bringen Sie nichts auf dem Gerät an und verdecken Sie das Gerät
nicht mit einem Tuch, Silikon, Klebstoff, Farbe, separater Abeckung etc.
Es können Feuer- oder Gerätestörungen auftreten.
DEUTSCH
Installieren Sie das Gerät nicht an einer der folgenden Orte. Feuer,
Stromschlag oder Gerätestörungen können die Folge sein.
- Orte unter direktem Sonnenlicht oder Orte in der Nähe von
Heizgeräten, die in der Temperatur variieren.
23
WARNUNG
- Orte mit Staub, Öl, Chemikalien, Schwefelwasserstoff (heiße Quellen).
- Orte, die extremer Feuchtigkeit und Luftfeuchtigkeit ausgesetzt sind,
wie Bäder, Keller, Gewächshäuser, etc.
- Orte, an denen die Temperatur extrem niedrig ist, wie z. B. in einem
gekühlten Bereich oder vor einer Klimaanlage.
- Orte, die Dampf oder Rauch ausgesetzt sind (z.B. in der Nähe von
Heiz- oder Kochflächen).
- Orte, an denen Geräusch erzeugende Geräte wie Dimmschalter oder
Wechselrichter-Elektrogeräte in unmittelbarer Nähe sind.
- Orte, die häufigen Vibrationen oder Stößen ausgesetzt sind.
Bei Geräten mit Gegensprechfunktion ist darauf zu achten, dass ein
Anruftest durchgeführt wird, bei dem beide Gegensprechgeräte auf
geringer Lautstärke eingestellt sind. Ein plötzlicher Anruf etc. kann
ankommen und das Gehör schädigen.
Wenn das Gerät nicht ordnungsgemäß funktioniert, ziehen Sie den
Netzstecker aus der Steckdose.
Alle Geräte, die nicht als wetterfest gekennzeichnet sind, sind nur für
den Innenbereich konzipiert und nicht im Freien zu benutzen.
Geräte, die als wetterfest gekennzeichnet sind, nicht mit Hochdruck wasser besprühen. Gerätestörungen können die Folge sein.
Bei Sach- oder Personenschäden, die durch unsachgemäße Hand habung oder Nichtbeachten der Gefahrenhinweise verursacht werden,
übernehmen wir keine Haftung. In solchen Fällen erlischt jeder
Gewährleistungsanspruch! Für Folgeschäden übernehmen wir keine
Haftung.
Sicherheitsanweisungen
NOTICE
Die Verwendung des Geräts muss unter Beachtung der örtlich
geltenden rechtlichen Bestimmungen erfolgen.
Lagern Sie das Gerät in einer trockenen und belüfteten Umgebung.
24
Achten Sie darauf, dass das Gerät weder Stößen noch starkem Druck
ausgesetzt ist.
Installieren Sie das Gerät nicht an instabilen Halterungen, Oberflächen
oder Wänden. Stellen Sie sicher, dass das Material stabil genug ist, um
das Gewicht des Geräts zu tragen.
Verwenden Sie bei der Installation des Geräts ausschließlich passende
Werkzeuge. Ein zu großer Kraftaufwand mit Werkzeugen kann das Gerät
beschädigen.
Verwenden Sie keine chemischen, ätzenden oder aerosolhaltigen
Reinigungsmittel.
Verwenden Sie zum Reinigen ein sauberes, trockenes Tuch.
Verwenden Sie nur Zubehör, das den technischen Daten des Geräts
entspricht. Dieses ist von Bird Home Automation GmbH erhältlich.
Verwenden Sie ausschließlich Ersatzteile die von Bird Home Automation
GmbH bereitgestellt oder empfohlen werden.
Versuchen Sie nicht, das Gerät selbstständig zu reparieren. Wenden
Sie sich bezüglich Reparatur und Wartung an Bird Home Automation
GmbH.
Halten Sie das Gerät mehr als 1 m (3,3") entfernt von Mikrowelle,
Radio, TV, WLAN Router und anderen drahtlosen Geräten.
Bei Geräten mit Gegensprechfunktion oder eingebautem Lautsprecher
oder eingebautem Mikrofon oder Signalübertragungsfunktion,
installieren Sie die Drähte mehr als 30 cm (12'') entfernt von 100-240 V
Wechselstromverdrahtung. Ansonsten können Wechselstrom-induzierte
Geräusche und/oder Geräte-Störungen auftreten.
Installieren Sie das Gerät in einem Bereich, der für zukünftige Inspek tionen, Reparaturen und Wartungen zugänglich ist.
Wenn das Gerät in der Nähe eines Mobiltelefons verwendet wird, kann
das Gerät gestört werden.
Das Gerät kann beschädigt werden, wenn es fallen gelassen wird.
Mit Vorsicht behandeln.
DEUTSCH
25
NOTICE
Das Gerät wird während eines Stromausfalls außer Betrieb gesetzt.
Bei Geräten mit Gegensprechfunktion oder eingebautem Lautsprecher
oder eingebautem Mikrofon kann das Gerät in Bereichen, in denen
Antennen von Mobilfunksendern, Radio- oder TV-Sendern in der Nähe
sind, beeinträchtigt werden.
Bei Geräten mit LCD-Bildschirm muss im Voraus darauf hingewiesen
werden, dass bei einem LCD-Panel, obwohl es mit sehr hohen Präzisions techniken hergestellt wird, unvermeidlich ein sehr kleiner Teil seiner
Bildelemente nicht immer beleuchtet oder gar nicht beleuchten wird.
Dies gilt nicht als Gerätefehler.
Bei Geräten mit Gegensprechfunktion können Umgebungsgeräusche
um das Gerät herum eine reibungslose Kommunikation behindern.
Dies ist keine Fehlfunktion.
Bei Geräten mit Benutzername/Passwort ist der Anwender für den
Zugriff mittels Benutzername/Passwort auf das Gerät verantwortlich.
Vergewissern Sie sich ein Passwort zu verwenden, das von einem
Dritten nicht leicht erraten werden kann. Wir empfehlen Ihnen, das
Passwort regelmäßig zu ändern.
Wir haften unter keinen Umständen für Schäden, die aufgrund von
Fehlern in der Stromversorgung, Netzwerkgeräten oder Endgeräten
auftreten; Ausfälle aufgrund von Internetanbietern und Mobilfunk anbietern; Ausfälle aufgrund von getrennten oder gestörten Leitungen
und andere Übertragungsverluste, die es unmöglich machen, unseren
Dienst zu erbringen, sowie allen anderen Ursachen die außerhalb
unserer Verantwortung liegen; Oder, wenn während der Übertragung
ein Fehler oder fehlende Daten auftreten.
Transport
NOTICE
Bei Bedarf transportieren Sie das Gerät in der Originalverpackung
oder einer entsprechenden Verpackung, so dass Schäden vermieden werden.
Gewährleistung
Informationen zur Gewährleistung des Geräts finden Sie unter
www.doorbird.com/de/warranty
26
KOMPONENTEN
Inhalt
1x DoorBird Video Türstation
1x Steckernetzteil mit vier Landesadaptern
1x Kabel mit Stecker für die Stromversorgung (schwarz, rot)
1x Kabel mit Stecker und RJ45 Buchse für das Netzwerkkabel
(weiß-orange, orange, weiß-grün, grün)
1x Kabel mit Stecker für das Netzwerkkabel (weiß-orange, orange,
weiß-grün, grün), als Alternative zum Kabel mit Stecker und RJ45 Buchse
1x Kabel mit Stecker für den elektrischen Türöffner (lila, lila)
1x Kabel mit Stecker für den elektrischen Türgong (blau, blau)
1x Kabel mit Stecker für den Türöffnertaster (gelb, gelb)
Einige Stoßverbinder
4x Kreuzschlitz-Senkkopfschraube für die Wandmontageplatte, lang
4x Kreuzschlitz-Senkkopfschraube für die Wandmontageplatte, kurz
4x Dübel
1x Sicherheitsschraube
1x Schraub-Tool für die Sicherheitsschraube
1x Wandmontageplatte mit Dichtungsring (Aufputzmontage)
1x Installationsanleitung
1x Quickstartanleitung
DEUTSCH
27
Loading...