DoorBird A1091 Series Installation Manual
1
Installation Manual (Pages 2-5)
GIGABIT POE-INJECTOR
A1091 Series
VERSION ., MIN. HW .
Installationsanleitung (Seiten 6-11)
GIGABIT POE-INJEKTOR
A1091 Serie
2
LAN IN
RJ45 jack to connect a standard
Network cable Cat.5 or better,
coming from the Internet Router.
PWR
Power Input Diagnostic-LED.
15 VDC IN
Power supply (Input, 15 VDC).
2
3
6
INSTALLATION MANUAL
You can always find the most up-to-date version of the installation manual
on www.doorbird.com/support
To make things easier we use the term „Device“ for the product „DoorBird
Gigabit PoE-Injector A1091“.
COMPONENTS
Contents
1x Device
1x Power supply unit
(mains adaptor) with four
country-specific adaptors
1x RJ45 network cable (300 cm)
1x DIN-Rail adapter
2x Phillips countersunk head screws
2x Dowels
1x Installation manual
1x Drilling template
1
4
5
POE
PoE Diagnostic-LED (Output).
POE + DATA OUT
RJ45 jack to connect a standard
Network cable Cat.5 or better,
going to the product to supply
with PoE and network data.
Screw holes
Two screw holes for mounting the
device on a wall or ceiling.
DEVICE
3
ENGLISH
VIDEOS
Need help with the installation? Be sure to watch our installation videos
which can be found on http://www.doorbird.com/support.
Each individual step of the installation is clearly documented in the videos.
INSTALLATION
All steps below should be carried out carefully by a competent adult, taking
into consideration any applicable safety regulations. Should you have any
questions, please contact us or a competent specialist directly. Please ensure
that all wires used for the installation are undamaged along their entire
length and approved for this type of use.
Network speed and network components
Please ensure that the upload speed of your Internet connection is at least
0.5 Mbps. You can also carry out a speed test at any time via the DoorBird
App. The user experience is only as good as your network speed, network
stability and quality of your network components, such as your Internet router
and WiFi access points or WiFi repeaters. Please also make sure that your network components are not older than two years, have been manufactured by a
well-known manufacturer, and have the latest firmware installed.
Should these requirements not be fulfilled, it may happen, for example that
the performance of audio and video is poor or push notifications are delayed
or do not arrive on your smartphone or tablet at all.
High-speed Internet (via landline): DSL, cable or optical fibre
Network: 802.11 b/g/n 2.4 GHz or Ethernet, with DHCP
STEP 1: SWITCHING OFF POWER
Switch off the power to all wires leading to the assembly location, i.e. the door
station, door chime, electric door opener, power supply unit, PoE-Switch /
PoE-Injector etc.
STEP 2: DETERMINING THE ASSEMBLY LOCATION
The device is IP50 certified (not water-proof). Please make sure to put the
device into an appropriate housing if you want to use it outdoors.
The network cable between the device and the product to supply with PoE
and network data can have maximum length of 80 meters/262 feet.
44
STEP 3: DOWELS AND SCREWS
You can mount the device permanently on a wall or ceiling using appropriate
screws. Please skip this step if you do not want to mount the device permanently.
Press the drilling template of the device against the wall or ceiling at the
desired installation site and mark the boreholes with a pencil. Remove the
drilling template again. Ensure that no cables are to be found in the wall
or ceiling behind the boreholes.
If the wall of the house is not made of wood, you should drill dowel holes
5 mm in diameter in the wall according to the drilling template and then place
the dowels provided into the boreholes. If the wall of the house is made of
wood, dowels are normally not required. There are special dowels for assembling
the device on an insulating wall, e.g. Fischer insulating dowels. Please check with
your insulating material manufacturer regarding which dowels they recommend.
Press the device on the wall or ceiling, so you can see the boreholes in the wall/
ceiling through the screw holes of the device. Use the Phillips countersunk head
screws provided to position it in the dowels or on the wall to fix the device on
the wall/ceiling.
STEP 4: INSTALLATION
Connect the network cable coming from your Internet to the RJ45 jack „LAN
IN“ of the device. Then connect a second network cable to the RJ45 jack
„POE + DATA OUT“ of the device. Connect the spare end of the network cable
connected to the RJ45 jack „POE + DATA OUT“ to the product you would
like to establish a PoE and network data connection with, e.g. a DoorBird IP
Video Door Station, DoorBird 2-Wire Ethernet PoE Converter (Sender) or an
IP Camera.
A Cat.5 network cable with RJ45 plug or better must be used to connect to
the „LAN IN“ and „POE + DATA OUT“ jacks of the device.
Connect the 5.5 mm DC plug of the Power supply unit (mains adaptor)
supplied with the device into the jack „15 VDC IN“ of the device. Do not plug
the Power supply unit itself into a wall socket yet.
STEP 5: ACTIVATING THE DEVICES
Switch on the power leading to the assembly location again. Then plug the
Power supply unit (mains adaptor) of the device into a wall socket.
Loading...