DoorBird A1061 Series Installation Manual
1
Installation Manual (Pages 2-9)
IP DOOR CHIME
A1061x Series
VERSION ., MIN. HW .
Installationsanleitung (Seiten 10-17)
IP TÜRGONG
A1061x Serie
22
INSTALLATION MANUAL
You can always find the most up-to-date version of the installation manual
on www.doorbird.com/support
To make things easier we use the term „device“ for the product „DoorBird IP
Door Chime“ and „mobile device“ for a smartphone or tablet.
COMPONENTS
Contents
1x Device
1x Power supply unit (mains adaptor) with four country-specific adaptors
1x RJ45 network cable (300 cm)
3x Phillips countersunk head screws
3x Dowels
3x Crimp connectors
1x Installation manual
1x Drilling template
1x Quickstart guide with Digital Passport
3
ENGLISH
VIDEOS
Need help with the installation? Be sure to watch our installation videos
which can be found on http://www.doorbird.com/support
Each individual step of the installation is clearly documented in the videos.
Device
Loudspeaker
Large-sized broadband speaker.
Cable inlet
To feed the cable into the device, if the
cables are surface-mounted.
Diagnostic-LED
To visualize the current status of the device.
Mounting points
To mount the device on a wall or ceiling
using countersunk head screws.
Connection terminal
Power supply (15 VDC -; 15 VDC +),
Storey-call button (STC),
Setup button (SET), LAN/PoE.
Front
Back
1
4
2
3
5
INSTALLATION
All steps below should be carried out carefully by a competent adult, taking
into consideration any applicable safety regulations. Should you have any
questions, please contact us or a competent specialist directly. Please ensure
that all wires used for the installation are undamaged along their entire
length and approved for this type of use.
44
Network speed and network components
Please ensure that the upload speed of your Internet connection is at least
0.5 Mbps. You can also carry out a speed test at any time via the DoorBird App.
The user experience is only as good as your network speed, network stability
and quality of your network components, such as your Internet router and
WiFi access points or WiFi repeaters. Please also make sure that your network
components are no more than two years old, have been manufactured by a
well-known manufacturer, and have the latest firmware installed.
Should these requirements not be fulfilled, it may happen, i.e. that the
performance of audio and video is poor or push notifications are delayed or
do not arrive on your smartphone or tablet at all.
High-speed Internet (via landline): DSL, cable or optical fibre
Network: 802.11b/g/n 2.4 GHz or Ethernet, with DHCP
STEP 1: SWITCHING OFF POWER
Switch off the power to all wires leading to the assembly location, i.e. the
door chime, electric door opener, power supply unit for the video door
station etc..
STEP 2: DISMANTLING THE EXISTING DOOR CHIME
Should there already be a door chime on the wall, please do not hesitate to
remove it.
STEP 3: DETERMINING THE ASSEMBLY LOCATION
The device is designed for indoor-use only. Press the drilling template of the
device against the wall or ceiling at the desired installation site and mark the
boreholes with a pencil. Remove the drilling template again. Ensure that no
cables are to be found in the wall or ceiling behind the boreholes.
STEP 4: DOWELS AND SCREWS
If the wall of the house is not made of wood, you should drill dowel holes 5 mm
in diameter in the wall according to the drilling template and then place
the dowels provided into the boreholes. If the wall of the house is made of
wood, dowels are not normally required. There are special dowels for assembling the device on an insulating wall, e.g. Fischer insulating dowels.
Please check with your insulating material manufacturer regarding which
dowels they recommend. Use the Phillips countersunk head screws provided
to position it in the dowels or on the wall, so that the countersunk head
screws protrude a few millimeters above the wall.
5
ENGLISH
STEP 5: PREPARING THE POWER SUPPLY
The device can be powered by two simple doorbell wires using the powersupply unit (mains adaptor) supplied with it or via PoE (Power over Ethernet)
using a network cable. The device can alternatively also be supplied with a
DIN-rail power supply unit that you can obtain from us directly. The device
does not use battery power.
Power supply using the power-supply unit (mains adaptor)
Two insulated wires are required to power the device by connecting it to the
power-supply unit (mains adaptor) supplied with it. These wires are normally
already there and are freely accessible once you have removed the previous
door chime. You can also connect the power supply without any additional
wires to the door chime, the power supply has a 300cm long cable with two
insulated wires. If you need longer wiring, connect the wires of the power
supply using the supplied crimp connectors with the two wires that you want
to use for the power supply.
Do not plug the power supply unit into the wall socket yet.
Only use the power supply unit provided along with the device, or a DIN-rail
power supply unit that you can obtain from us separately, since this has
been specially stabilized electrically and is equipped with an integrated audio
interference reduction device. Other power supply units may destroy the
device or cause poor transmission quality. The warranty automatically expires
if you use a different power supply unit. The power supply unit is plugged
into a wall socket inside your house, usually where the two wires from your
previous door chime comes out of the wall in the interior of the house.
Power supply via PoE (as an alternative)
To power the device via a PoE-Switch (e.g. D-Link DGS-1008P) or PoE-Injector
(e.g. DoorBird Gigabit PoE Injector or TP-Link TL-PoE150S) in accordance with
the PoE standard IEEE 802.3af Mode A, the four wires bearing the numbers 1,
2, 3 and 6 of a Cat.5 cable or better are to be used. A Cat.5 cable or better must
be used as network signals can only be transmitted over completely insulated,
shielded and twisted cables. If you use PoE as a source of power, the WiFi
interface of the device is automatically inactive, and the four wires for PoE then
simultaneously form the data link. The device won’t start if your PoE Switch
or PoE injector does not support the PoE Standard IEEE 802.3af Mode A (see
Diagnostic-LED and Diagnostic-Sounds).
1. Disconnect the PoE-Switch or PoE-Injector from the power grid.
2. Place the network cable in the installation site of the device.
Do not combine the power supply from the power supply unit (mains adaptor)
with the power supply via PoE. You can find further information about PoE
here: http://www.doorbird.com/poe
66
Be sure to use
four insulated,
shielded and
twisted wires of
a network cable
in accordance
with the Cat.5
standard or
better. Only four
wires of the
network cable
will be used.
Connecting the unit to a network
You can connect the device to your existing network
via WiFi, or alternatively use a network cable (Ethernet).
For reasons of network stability, we principally recommend using a network cable, as WiFi is sensitive to
interference (range, house walls acting as shields, reliability of performance, third party WiFi networks, wireless
transmitters causing interference in the area, etc.).
The device can be powered by PoE or using the power
supply unit provided. If you use PoE as a source of power,
the WiFi interface of the device remains inactive.
Use only a network cable with RJ45 plug that meets the
Cat.5 standard or a better one.
Connect the network cable to your PoE-Switch or
PoE-Injector that is connected to your Internet router.
Then connect it to the device.
Conventional Storey-call button
You can connect a conventional button to the device
to realize a separate storey-call. A Storey-call button is
typically used if you have more than one door, e.g. street
door and apartment door. Please make sure to add no
extra voltage on that contact.
STEP 6: FURTHER CONNECTIONS (OPTIONAL)
If desired, connect additional wires to the installation site of the device.
The wires or connection options mentioned in this section are optional.
STEP 7: PREPARING THE WIRES
Remove about 5 mm of insulation material at the end of the wires that you
would like to connect to the device (Power supply, Storey-call button).
STEP 8: CONNECTING THE WIRES
It is possible to connect the cables and wires to the device conveniently and
safely via a connection terminal on the reverse of the device. The individual
contacts on the connection terminal are labelled on the casing. You can
connect all necessary cables and wires to the device using the connection
terminal now. Please remove any cables and wires on the connection
terminal that you do not need.
Two insulated
wires.
6 (R-)
3 (R+)
2 (T-)
1 (T+)
Loading...