DoorBird A1061 User guide [ml]

Page 2-17

Installation Manual

IP Door Chime

A1061x Series

Seite 18-34

Installationsanleitung

IP Türgong
A1061x Serie

A1061X

VERSION ., MIN. HW .

INSTALLATION MANUAL

Read these instructions carefully before starting to use any components.
Keep the manual so you can refer to it at a later date if required. If you hand
over the device to other persons for use, please hand over the operating
manual as well.

To make things easier we use the term “device” for the product “DoorBird IP
Door Chime” and “mobile device” for a smartphone or tablet. You can always find
the most up-to-date version of the installation manual on www.doorbird.com/
support

Liability

Every care has been taken in the preparation of this document.
Please inform Bird Home Automation GmbH of any inaccuracies or omissions.
Bird Home Automation GmbH cannot be held responsible for any technical
or typographical errors and reserves the right to make changes to the product
and manuals without prior notice. Bird Home Automation GmbH makes no
warranty of any kind with regard to the content of this document, including,
but not limited to, the implied warranties of merchantability and fitness for
a particular purpose. Bird Home Automation GmbH shall neither be liable
nor responsible for incidental or consequential damages in connection with
the furnishing, performance or use of this material. This product is only to
be used for its intended purpose.

Equipment Modifications

This equipment must be installed and used in strict accordance with the
instructions given in the user documentation. This equipment contains no
components that require service by the user. Unauthorized equipment
changes or modifications will invalidate all applicable regulatory certifications
and approvals.

Symbols used

Danger: Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Warning: Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.

Caution: Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.

22

NOTICE

Hazard information

Notice: Indicates a situation which, if not avoided, could result

in damage to property.

Important: Indicates significant information which is essential
for the product to function correctly.

Note: Indicates useful information which helps in getting the
most out of the product.

WARNING

 Mounting, installation and servicing work on electrical devices may
only be performed by a qualified eletrician. Failure to observe this
regulation could result in the risk of serious damage to health or fatal
injury due to electric shocks.

 Devices with 110-240 V connection: The device may only be connected
to an easily accessible power socket outlet. The mains adapter must
be pulled out if a hazard occurs.

 For power supply, only use the original plug-in mains adapter
delivered with the device or a recommended PoE-Switch/PoE-Injector
as specified in this manual.

 Because of electrostatic charging, direct contact with the circuit
board can result in destruction of the device. Direct contact with the
circuit board must therefore be avoided at any time.

 Observe the EN 60065 resp. EN 60950 resp. EN 62368 standard.

 Do not use the device if there are signs of damage to the housing,
control elements or connecting sockets, for example, or if it
demonstrates a malfunction. If you have any doubts, please have
the device checked by an authorized expert.

 Do not open the device. This voids the warranty of the device.
The device does not contain any parts that can be maintained by the
user. In the event of an error, please have the device checked by an
authorized expert.

ENGLISHENGLISH

33

WARNING

 For safety, approval and licensing reasons (CE/FCC/IC etc.), unauthorized
change and/or modification of the device is not permitted.

 The device is not a toy; do not allow children to play with it. Do not
leave packaging material lying around. Plastic films/bags, pieces of
polystyrene, etc. can be dangerous in the hands of a child.

 Always lay cables in such a way that they do not become a risk to
people and domestic animals.

 Voltage is applied to parts within the equipment. Do not touch any
parts that are not associated with the installation, wiring, or connection.
Electric shock could result.

 On devices which are not marked as weather-proof: Keep the device
away from water or any other liquid.

 Do not install or make any wire terminations while power supply is
plugged in. It can cause eletric shock or damage to the device.

 Before turning on power, make sure wires are not crossed or shorted.
If not, fire or eletric shock could result.

 High voltage may be present internally. Do not open the device.
Electric shock could result.

 The device is not of explosion-proof. Do not install or use near gases
or flammable materials. Fire or explosion could result.

 Do not install two power supplies in parallel to a single input. Fire or
damage to the device could result. Be sure to connect a single power
supply to the device.

 Do not connect any terminal on the device to an AC power line. Fire
or electric shock could result.

 Keep AC cord from being marred or crushed. If the AC cord is fractured,
fire or electric shock could result.

 Do not plug or unplug with wet hands. Electric shock could result.

44

 Do not put any metal or flammable material into the device.
Fire, electric shock, or device trouble could result.

 Existing wiring such as chime wiring, etc. may contain high voltage
AC electricity. Damage to the device or electric shock could result.
Wiring and installation must be done by a qualified eletrician.

 When mounting the device on a wall or ceiling, install the device in
a convenient location, but not where it could be jarred or bumped.
Injury could result.

 On devices with ground terminals, connect to an earth ground.
Otherwise fire or malfunction could result.

 On devices with plastic or real glass, do not put high pressure on
the glass. If fractured, injury could result.

 On devices with LCD, if LCD is punctured, do not allow contact
with the liquid crystal inside. Injury could result. If necessary, gargle
your mouth and clean your eyes or skin with clear water for at least
15 minutes and consult your doctor.

 Do not put anything on the device or cover the device with cloth,
silicone, glue, coating, separate covering etc. Fire or device issues
could result.

 Do not install the device in any of the following locations. Fire, electric
shock, or device trouble could result.

- Places under direct sunlight or places near heating equipment that
varies in temperature.

- Places subject to dust, oil, chemicals, hydrogen sulfide (hot spring).

- Places subject to moisture and humidity extremes, such as bathrooms,
cellars, greenhouses, etc.

- Places where the temperature is very low, such as inside a refrigerated
area or in front of an air conditioner.

- Places subject to steam or smoke (e.g. near heating or cooking surfaces).

- Where noise generating devices such as dimmer switches or inverter
electrical appliances are closeby.

- Locations subject to frequent vibration or impact.

ENGLISHENGLISH

55

WARNING

 On devices with intercom, be sure to perform a call test with low
audio volume on both intercom devices. A sudden call etc. may arrive
causing for example damage to your ear.

 If the device does not operate properly, unplug the power supply.

 All devices which are not marked as weather-proof are designed for
indoor use only. Do not use outdoor.

 On devices which are marked weather-proof: Do not spray with
high-pressure water. Device issues could result.

 We do not assume any liability for damage to property or personal
injury caused by improper use or the failure to observe the hazard
information. In such cases, any claim under warranty ceases.
For consequential damages, we assume no liability!

Safety instructions

NOTICE

 The device shall be used in compliance with local laws and regulations.

 Store the device in a dry and ventilated environment.

 Avoid exposing the device to shocks or heavy pressure.

 Do not install the device on unstable brackets, surfaces or walls.
Make sure the material is strong enough to support the weight of
the device.

 Use only applicable tools when installing the device. Using excessive
force with tools could cause damage to the device.

 Do not use chemicals, caustic agents, or aerosol cleaners.

 Use a clean dry cloth for cleaning.

 Use only accessories that comply with technical specification of the
device. These can be provided by Bird Home Automation GmbH.

 Use only spare parts provided by or recommended by Bird Home
Automation GmbH.

 Do not attempt to repair the device by yourself. Contact Bird Home
Automation GmbH for service matters.

66

 Keep the device more than 1 m (3.3') away from microwave, radio, TV,
wireless router and any other wireless devices.

 On devices with intercom or built-in speaker or built-in microphone
or signal transmission functions, keep the wires more than 30 cm (12'')
away from AC 100-240 V wiring. AC induced noise and/or device
malfunction could result.

 Install the device in an area that will be accessible for future inspections,
repairs and maintenance.

 If the device is used close to a cellular phone, the device may malfunction.

 The device can be damaged if dropped. Handle with care.

 The device turns inoperative during power failure.

 On devices with intercom or built-in speaker or built-in microphone,
in areas where cellular or Radio / TV broadcasting station antennas are
closeby, the device may be affected by radio frequency interference.

 On devices with LCD screen, it must be noted in advance that the LCD
panel, though manufactured with very high precision techniques,
inevitably will have a very small portion of its picture elements always lit
or not lit at all. This is not considered a device malfunction.

 On devices with intercom, due to the environmental sound around
the device, it may hinder smooth communication, but this is not a
malfunction.

 On devices with Username/Password, the Username/Password to
access the device is the customer's responsibility. Make sure to use
password that cannot be easily guessed by a third party.
We recommend that you change the Password on a regular basis.

 We will, under no circumstances, be liable for damage that occurs due
to failures in power supply, network equipment or terminal devices;
failures due to Internet providers and cellular network providers;
failures such as disconnected lines and other losses in communication,
which makes it impossible to provide this service as well as in any way
delay this service due to any other causes outside of our responsibility;
or if an error or missing data occurs during transmission.

ENGLISHENGLISH

77

Transportation

NOTICE

Warranty Information

For information about the device warranty, see www.doorbird.com/warranty

When transporting the device, use the original packaging or
equivalent to prevent damage to the device.

COMPONENTS

Contents

 1x Device

 1x Power supply unit
(mains adaptor) with four
country-specific adaptors

 1x RJ45 network cable (300 cm)

 3x Phillips countersunk
head screws

 3x Dowels

 3x Crimp connectors

 1x Installation manual

 1x Drilling template

 1x Quickstart Guide with Digital
Passport

Device

Front

1

Loudspeaker
Large-sized broadband speaker.

Cable inlet

2

To feed the cable into the device, if the
cables are surface-mounted.

3

Diagnostic-LED
To visualize the current status of the device.

88

Back

4

Mounting points
To mount the device on a wall or ceiling
using countersunk head screws.

Connection terminal

5

Power supply (15 V DC -; 15 V DC +),
Storey-call button (STC),
Setup button (SET), LAN/PoE.

Cable clamp

6

VIDEOS

Need help with the installation? Be sure to watch our installation videos
which can be found on http://www.doorbird.com/support

Each individual step of the installation is clearly documented in the videos.

INSTALLATION

All steps below should be carried out carefully by a competent adult, taking
into consideration any applicable safety regulations. Should you have any
questions, please contact us or a competent specialist directly. Please ensure
that all wires used for the installation are undamaged along their entire
length and approved for this type of use.

Network speed and network components

Please ensure that the upload speed of your Internet connection is at least

0.5 Mbps. You can also carry out a speed test at any time via the DoorBird App.
The user experience is only as good as your network speed, network stability
and quality of your network components, such as your Internet router and
WiFi access points or WiFi repeaters. Please also make sure that your network
components are no more than two years old, have been manufactured by a
well-known manufacturer, and have the latest firmware installed.

Should these requirements not be fulfilled, it may happen, i.e. that the
performance of audio and video is poor or push notifications are delayed or
do not arrive on your smartphone or tablet at all.

High-speed Internet (via landline): DSL, cable or optical fibre
Network: 802.11b/g/n 2.4 GHz or Ethernet, with DHCP

ENGLISHENGLISH

99

STEP : SWITCHING OFF POWER

Switch off the power to all wires leading to the assembly location, i.e.
the door chime, electric door opener, power supply unit, PoE-Switch/
PoE-Injector etc.

STEP : DISMANTLING THE EXISTING DOOR CHIME

Should there already be a door chime on the wall, please do not hesitate to
remove it.

STEP : DETERMINING THE ASSEMBLY LOCATION

The device is designed for indoor-use only.

Press the drilling template of the device against the wall or ceiling at the
desired installation site and mark the boreholes with a pencil. Remove the
drilling template again. Ensure that no cables are to be found in the wall or
ceiling behind the boreholes.

STEP : DOWELS AND SCREWS

If the wall of the house is not made of wood, you should drill dowel holes 5 mm
in diameter in the wall according to the drilling template and then place
the dowels provided into the boreholes.

If you must drill holes in a wall, insert screws into a wall or lever up a
wall, ensure that no cables or mains (gas, water, etc.) are to be found
in the wall.

If the wall of the house is made of wood, dowels are not normally required.
There are special dowels for assembling the device on an insulating wall, e.g.
Fischer insulating dowels.

Please check with your insulating material manufacturer regarding which
dowels they recommend. Use the Phillips countersunk head screws provided
to position it in the dowels or on the wall, so that the countersunk head
screws protrude a few millimeters above the wall.

STEP : PREPARING THE POWER SUPPLY

The device can be powered by two simple doorbell wires using the power­supply unit (mains adaptor) supplied with it or via PoE (Power over Ethernet)
using a network cable. The device can alternatively also be supplied with a
DIN-rail power supply unit that you can obtain from us directly. The device
does not use battery power.

1010

Option 1: Power supply using the power-supply unit (mains adaptor)

Two insulated wires are required to power the device by connecting it to the
power-supply unit (mains adaptor) supplied with it. These wires are normally
already there and are freely accessible once you have removed the previous
door chime. You can also connect the power supply without any additional
wires to the door chime, the power supply has a 300cm long cable with two
insulated wires. If you need longer wiring, connect the wires of the power
supply using the supplied crimp connectors with the two wires that you want
to use for the power supply.

Do not plug the power supply unit into the wall socket yet.

NOTICE

Only use the power supply unit provided along with the device, or a
DIN-rail power supply unit that you can obtain from us separately,
since this has been specially stabilized electrically and is equipped
with an integrated audio interference reduction device. Other power
supply units may destroy the device or cause poor transmission quality.
The warranty automatically expires if you use a different power supply
unit. The power supply unit is plugged into a wall socket inside your
house, usually where the two wires from your previous door chime
comes out of the wall in the interior of the house.

Option 2: Power supply via PoE (as an alternative)

To power the device via a PoE-Switch (e.g. D-Link DGS-1008P) or PoE-Injector
(e.g. DoorBird Gigabit PoE Injector) in accordance with the PoE standard IEEE

802.3af Mode A, the four wires bearing the numbers 1, 2, 3 and 6 of a Cat.5
cable or better are to be used. A Cat.5 cable or better must be used as network
signals can only be transmitted over completely insulated, shielded and
twisted cables. If you use PoE as a source of power, the WiFi interface of the
device is automatically inactive, and the four wires for PoE then simultaneously
form the data link. The device won’t start if your PoE Switch or PoE injector
does not support the PoE Standard IEEE 802.3af Mode A (see Diagnostic-LED
and Diagnostic-Sounds).

1. Disconnect the PoE-Switch or PoE-Injector from the power grid.

2. Place the network cable in the installation site of the device.

Do not combine the power supply from the power supply unit

NOTICE

(mains adaptor) with the power supply via PoE. You can find further
information about PoE here: http://www.doorbird.com/poe

ENGLISHENGLISH

STEP : FURTHER CONNECTIONS (OPTIONAL)

If desired, connect additional wires to the installation site of the device.
The wires or connection options mentioned in this section are optional.

1111