Doorbell Wireless Battery Video Doorbell Quick Start Guide
Wireless Battery Video Doorbell
Quick Start Guideline
* Please read it carefully before using the product,
and safe keeping
Packing List
After opening the package, please make sure the doorbell
(hereinafter referred to as the”Equipment”) is in good condition
verify parts below is complete.
Equipment
(including Conductive the
installation support)
Screw Package (including screws)
Appearance Introduction
PIR
Light Sensor
IR LED
MIC
Button
Speaker
IR LED
Light Sensor
MIC
Button
PIR
Lens
Indicator Ligh
Lens
Indicator Light
The ambient light is not enough, to enable the
infrared light, increase the environmental brightness
Used to collect environmental brightness value,
when the intensity of illumination is less than 2 Lux,
enable the IR LED
Audio capture
The doorbell button
When human body movement in front of the
equipment, the equipment could be made the
notification to your mobile phone.
Video image capture
Blinking blue: configuration status;
Long red light: failed to connect wifi;
Blue light is on: the device is connected successfully
Red and blue light together: The device is
connected to WiFi
Security Screw
Quick Start
Guideline
Quick Start Guide
USB Interface
TF card
Reset Button
AC Input
Battery
Comartment
AC Input
Reset Button
Battery Compartment
Fixed Hole
AC Input Hole
Stuck Hole
Security Screw Hole
TF card TF card maximum support 32G
Power is supplied to the equipment by
installing the AC input supply hole on the
mounting bracket.
Equipment working status, long press 5
seconds to restore factory settings
Mounting 18650 specification battery.
Fit the support on the wall with the mounting
screws for the mounting kit.
The power supply of the equipment can be
supplied by connecting the hole and the AC
power supply on the wall
Mounting the equipment onto the bracket
Mounting the security screw on the fittings to
prevent the equipment from being removed
Installation Guide
As shown in the figure, take back
Use the screws in the mounting kit to fit
1
the bracket on the wall
Fixed Hole
Mounting three 18650 specification batteries
3
Press the reset button for 5 seconds, waiting
4
for the indicator light to slow down(The
equipment should be in working condition,
long press, sleep state is invalid)
Cover the battery cover, align the equipment
5
and the bracket, push down and lock the
security screws to complete the installation
Setup Device
Thank you for choosing our products! Please follow the below
instruction to setup and using your doorbell device.
1. Downloading and Installing the App
Open the App Store (for iOS) or the Google Play Store(for Android)
on your mobile devices. Search for "XSHcam" or scan the following
QR Code to download and install to your device.
APP-AndroidApp Google playApp iOS
2. Setting up the App
Before you begin…
> Make sure the XSHcam app is installed to your device.
> Make sure that your device is connected to a 2.4GHz Wi-Fi network,
NOT a 5GHz network.
Add the camera
1.) Launch the XSHcam app on
your device and tap Add a
Camera.
Seup the Camera
2.) Select Setup Camera.
Note: If you have multiple cameras,
only setup one at a time.
3.) Before setup, make sure the
device is in configuration --- with
a voice prompt "The camera is
now ready to begin pairing".
5.) The name of the Wi-Fi network
will automatically be filled in, enter
the Wi-Fi password. And adjust the
volume of your device to a
reasonable level then tap "Next". The
APP will fill the corresponding
password automatically if connected
with the same Wi-Fi, and you don't
need to fill the password again.
6.) The mobile device will emit sound
waves, keep quiet and make sure about
30cm distance between the phone and
the device , and waitting for the device to
configure the network.
If your camera fails to connect, reset the
camera and repeat all the steps(please s
ee the previous section, Resetting
the Camera)
7.) After a successful connection, you
will be prompted to create a name and
password for your camera. The
password must be at least 8 characters
and include an uppercase letter, a
lower-case letter, and a number.
4.) If you didn't hear the voice
prompt, press and hold the
reset button for 5 seconds.
Release after the LED indicator
turnned off , and the device will
restart to configure automatically.
Speaker
Make a sound of the equipment, and voice intercom
8.) Setup completed! The APP will be
entered the device list interface
automatically. Congratulations!
The device is ready for use.
3.The Wi-Fi Doorbell Features
In the device list section, please click settings icon which at the top
right corner to enter the device settings.
Accept call
Turn on - Receive the notification if somebody
press the doorblle or call out.
Turn off - Will not receive the notifications for
accept call.
Call reminding
Share QR Code
Send the QR code to share the device to your
friends and family or someone that you want
to share.
QR code
Delete camera
The mobile device will not receive the
notifications after you delete the camera. But
the camera still works and the other connected
mobile devices still able to receive the notifications.
删除设备
Deleting equipment
Call reminding
QR code
Set up
删除设备
Deleting equipment
4.PIR Detection Instructions
The device can support the PIR detection. Tap "PIR detection" to
open the submenus.
Disabled - Close the PIR function.
Low The device will be able to wake up after device
detects human for 7 seconds. Device start to
take videos and call the mobile device at the
same time.
Medium The device will be able to wake up after device
detects human for 5 seconds. Device start to
take videos and call the mobile device at the
same time.
High In the state, the device will be able to detect if
keep the state what be detected at least 1
second, and the device start to take videos
and call to phones at the same time.
5.Cloud Storage
In the XSHcam APP setting
menu, choose storage managment, and open Cloud Storage
Cloud Storage Description: When the device is in sleep state,
when PIR triggered or the doorbell button was pressed , the device
will automatically upload 10 seconds of video to the cloud. Each
device can record 20 events per day, and provide a week of loop
recording space and Traffic for users
Tap the calendar icon in the
upper right corner and select
the date to see all the cloud
videos for the selected date
At the bottom of the preview
page, the "Switch" button in the
panorama mode becomes the
"Cloud Storage" button
Click on the event video to
see the cloud video
Note: In crowded environment, it is recommended to close or set the device to low
sensitivity to reduce device arousal and call times to extend battery life.
6.Note for using
1.) The device is powered by rechargeable lithium batteries. With fully charged, the
battery life approx be six months. The mobile device APP will be prompted while
the battery voltage is low. Please charge the device after received the reminder.
2.) Keep the camera in range of your router.
Make sure to pick a place within range of your network. Thick or insulated doors
can greatly reduce the strength of your Wi-Fi signal even if your router is close
by, so you should try streaming video before you mount your camera.
3.The device is a low power consumption intelligent products, can support remote
wake up from the APP, PIR human detection, press doorbell wake up. The device
will be works for 30 seconds after wake up then be in the resting state
automatically and until to next waking up.
Technical Specification
Resolution
Field of Angle View
IR LED
Wi-Fi
Audio
Recording
Storage
Battery
Device Wakeup
Power Consumption
Monitoring
Notifications
Three 18650 specification batteries, work regularly for 9
months.
1280* 720
166°
6*850mm
IEEE 802 11 b/ g/ n
Two-way talk with noise cancellation
Device SD Card recording(20 seconds)
Cloud storage or 8G/16G/32G TF Card
Two18650 specification batteries
Device Button, Motion Detection,
Remote Live View
Three pcs 18650 lithium battery
Within600 ms
Power Consumption Standby200 uA,
Working170 mA
Ding-dong Pairing
(Needs to be purchased separately)
Code Pairing: 1.Short press the button of Ding-dong responder,
indicator light is always on
2.Press the button of doorbell to make the code
successful
Reset: 1.Press the button of Ding-dong for 5 seconds.
Number of connections: 1 Ding-dong can connect with12
Doorbells;
1 Doorbell can connect with unlimited
amount of Ding-dongs.
Function Introduction
Three 18650 specification batteries work regularly for 9
months
Million HD pixels collocated with wide-angle lens
Support mobile phone remote fast wakeup device
within 1 second.
2.4G Wi-Fi connection
High quality two-way talk with noise cancellation
Support PIR motion detection,when someone hovers at
the door, immediately alerts push notifications to the
mobile phone.
Day and night mode automatic switching, whether day or
night, the image is clearly visible, for your、safety and
family security.
Loading...