Dongma ADL1588 Assembly And Operation Instructions

 Age range：37~96months

 Load limit：25kg

 The assembling and recharging process should be performed by adults.

Assembly and Operation Instruction

Please read this directions carefully before assembling and using. After reading,

please keep it carefully for possible future use.

Electric baby stroller

ITEM NO：ADL1588

For the first use,suggested charging time is 4-6hours

Content：

1. Profiles and specification

2. Breakdown drawing

3. Assembling step

4.Instructions

5.Charging

6.Repairs

7.Maintenance

Profiles and specification

Age： 37~96 months Battery： 2*6V4AH

Max weight： ≤25kg Size of car： 1050*550*490cm

Speed： 3~5km/h Power

way：

Charger：220V

Recharger

Doubledrive:Output:

DC12V0.5A

8~12 hours Fuze:

Average

battery life：

Charger way

Approximately280times

Self-resetting fuse

times

：

Exploded view

-

No. Name No. Name No. Name No. Name
1 Car body 5 Rearview mirror 9 Front wheel 13 rear prop
2 Windscreen 6 seat 10 Wear ring
3 Dashboardl 7 Rear wheel 11 Shim
4 Steering wheel 8 Gearbox 12 steering yoke

Assembling steps



The assembling process before using has to be operated by adults.The whole

process takes approximately 30 minutes.

 Minute parts has potential danger of choking.Children should be forbidden

touching and playing

！

 Tools needed in assembling:screwdriver (self-provided),vice(self-provided)

Before assembling,please check the number of all the parts .The plastic package

should be kept away from children since there’s danger of choking

Installing rear axle and rear wheel:

Rear wheel:

 Put the driving gear box into the back-shaft from the left of

the car(make sure the motor cable connector is through the

hole on the car and reach the battery cartridge from the left

of the car)The use of light-emitting wheel will be shining

round power line on the motor through the hole, non

luminous wheel is not required.

 Loaded wheel, which coincided with the connector

matching.

 Slightly forced by the boss wheels, and the wheels under

pressure, the wheel assembly in place. (remark: pull the

wheel to the outer pull to confirm the wheel assembly in

place)

 On the other side of the assembly.

 According to the picture,put the spring and spring support into

hole.

 Put rear axle through the side hole

 Make spring support down,put rear axle through the spring

support’s hole.

 The same operation with another spring support.

 Loaded wheel, which coincided with the connector matching.

 Slightly forced by the boss wheels, and the wheels under

pressure, the wheel assembly in place. (remark: pull the wheel

to the outer pull to confirm the wheel assembly in place)

 On the other side of the assembly.

Note: single drive only one drive motor

Assembling steps

 Put the bayonet the corresponding net.When

hearing the click sound.It means the buckle has

been installed in place

 Put the screw hole on the rear support right to the

screw post on the noumenon

 Use screw driver to screw in the 4x12tapping screw

 Put 12gasket*1 on one side of the front wheel

 Load wheel*1

 Slightly forced by the boss wheels, and the wheels under

pressure, the wheel assembly in place. (remark: pull the wheel

to the outer pull to confirm the wheel assembly in place)

 On the other side of the assembly.

 Put up the windscreen,then according to the

picture,put wing mirror’s hole into the screw

post on the windscreen(pay attention to the left

and right )



Using the same method to install on the other

side of the mirror.

Installing front wheel:

Installing rear support：

Installing windscreen：

Installing wing mirror：

Assembling steps

 Connect the electricity wire on the car to that

of the motor

 Connect the red wire to the electricity jar and

the black wire to the black end.



Screw off the 4x12 tapping screw of the

car

 Snap the buckle on the back of the

cushion into the neck.

 Use two 4x12tapping screws to make it

set



Use the screw driver to unload the M5x35

inorganic screws.

 Connect the lead plug-in on the steering wheel to

that of the open holes,and plug the steering wheel

in to the end of the steering tube(pay attention that

the plug-in is along the hole).Make sure the hole

on the steering wheel is lined with the steering

tube,then screw in the M5x35 inorganic screw.

 Screw in the M5nut



Push the plug into the hole in the body.

 The hole and push on the hole on the body

aligned, penetrating M5 screws with nut.

Installing steering wheel:

Connect the power：

Installing plug：

Installing the seat：

Note: if you do not push, the installation

is not.

How to use it(please make sure the switch is on

Manual：

Forward：

1. Press the “Forward/backward”switch to forward；

2. Slightly step on “foot switch”,the car will moving forward

Stop：

Lifting the foot to loosen the “foot switch”,the car will stop

Backward：

1. Press Switch the “forward/backward switch ”to “backward”；

2. Slightly step on the “foot switch”the car will moving backward.

Remote control ： (remarks ： in this mode there’s no remote control/manual

switch）

Warning!

When change the

gear,please make sure

the car is completely

stopped.Or it will

damage the gear case

and motor

)

Note: remote control should be used by the

How to use it(please make sure the switch is on)

2.4GWireless stroller controller instructions

For the first time using the code, the following steps:

Step one：Installed on two AAA1.5V batteries, the remote control battery cover down

to push the battery cover to open the battery (note the positive and negative polarity of

the battery chamber), and finally close the battery cover, the indicator flashes three

instructions battery is installed correctly;

Step two：Press the button for 2 seconds, frequency of flicker light;

Step three：Immediately turn on the power, the frequency will go out immediately,

while the frequency of success；

Step four：If the frequency of the frequency is not successful (the frequency is not out),

turn off the power, repeat step two and step three;

一、Normal use

1. Speed choose: 3 light flashes slowly at low speed, medium speed medium speed is

3 light flashing, flashing lamp is 3 high speed high speed, each gear speed with

variable speed slow start;The forward and backward button has a slow stop, press the

left and right keys can be left and right, press the emergency stop button in any case to

stop；

2.Press the emergency stop button on the remote control or manual, the vehicle can

stop moving;

3.15 seconds after the remote control is not used automatically cut off the power, again

use no re - frequency;

guardian, the child can not touch.

How to use it(please make sure the switch is on

1. The distance of the remote control car when baby and child adult ride

shall not exceed the range of 15M.

2. The remote control only allows the guardian to use, and can not let

the children touch.

3. Before the remote operation to read the instructions carefully, and

empty experiment, master, can make children ride and use.

4. remote control with energy saving, when a period of time (about 10

seconds), the automatic power failure, all the lights are off, and then

re work when the key;

5. The frequency keys are required to be re operated for the first time

using and replacing the battery；

6. The remote control car may not travel on the road and the water source,

the obstacle, etc.

7. Remote control shall not be allowed to rain or other ways to avoid damage

caused by immersion line.

8. Old batteries and different brands of batteries not mixed use.

9. For a long time no application for remote control, it is recommended

to remove the battery, so as to avoid battery leakage, corrosion circuit

board, so that the damage to remote control.

10. In the remote control process should avoid the remote control fell.

11. The battery with the correct polarity, the battery is strictly

forbidden to short-circuit.

12. Rechargeable batteries can only charge under the adult guardianship.

Non rechargeable battery can not charge.

13. The exhausted battery should take out the battery from the toy,

properly handle, prevent the children to play.

14. When long time no toys, we should take out the battery from the toy,

properly handle and prevent children to play..

15. Such as remote control range less than 3 meters, remote control

battery power shortage, to replace the two No. 5 (1.5V) battery.

Battery warning：

)

Music：

Push the button on the steering wheel,there will be trumpet or music

Using the method of auxiliary wheel, handle and matters

needing attention：

1.When the car is insufficient, turn off the power.

2.The front bumper on the pulling out, after the bumper on the auxiliary

wheel spins.

3.Then hold the handle, the car will be brought into 45 degrees, drag the

car.

4.No children ride in the car using the handle auxiliary wheel.

5.This operation must be adult operation.

Usage

Charging：



Power switch must be turned in off when charging

 Charging seat is located in the rear right.

 Plug the charger into a local mains power wall outlet

 Plug in the charging seat on the electricity power

 The charging process has to be operated by adults.

 Before the firsts use of the car,make sure the battery has been

charged more than 4-6hours.Or the battery would be damaged

permanently and cannot be repaired.

 When charging,please turn of the battery.Put the charger plug into

the charging hole before plug it on the socket.The car cannot be

operated when charging.

 When the battery is low,please charge it in time.Normally the

charging hour is 8-12hours,but do not charge it more than

20hours.

 It is normal that the battery jar emits heat,but when the

temperature is too high,you should examine whether the

recharging process is over-current or short-current.

 When there is water in socket aperture,the battery jar cannot be

charged since it will cause short-current.

 Only chargers and battery equipped by this car can be

used.Chargers and battery jars of other brand are strictly

prohibited .Or the charger and battery might be damaged.

 When the product is packed away or will not be used for a long

time,you have to fully charge the battery and charge it once every

Matters need attention when charging:

month to guarantee the life of the battery.

 The charger and the battery are not toy.Children should not be

allowed to play with them.

Warning：



The assembling and charging process could only be operated by

adults.

 Before use,please check whether all the part are installed well to

position and connected tightly

 When playing this car,the distance between the car and an adult

cannot be more than 10 meters



This car should only be rode under adult’s supervision

 This car cannot be used on dangerous places like

streets,roads,slopes and raceways.When there is barrier ,please

change directions to avoid it.

 Do not use it on smooth surfaces like marbles,floor tiles and

glasses .



Do not use this car on rainy or snowy days.

 Do not switch the forward/backward switch when

advancing.Make sure kids are not standing on the seat.



Do not change the structure,line and additional electrical devices

without permission.

 The car is outfit with seat belt,Make sure the Child has fastened

it.

 When the car is not used,please switch off the electric power

source;When not used for a long time,pluck off the attaching

plug.

 Examine the product and charger regularly to see whether the

parts are becoming old or dropped off.When damage is found,the

product should be stopped using until fixed.

Simple Maintenance：

Fault type

Reason analysis

Exclusion methods

Car’s not moving

1.Battery has low voltage

2.Fuse protection

3.The nut of the wheel is dropped

off

4.Socked connector of the battery

has fallen off

5.Battery is flat

6.Electrical damage

7.Motor is broken

1.Recharging the battery

2.Stop for several minutes before

using again

3.Screw the nut on

4.Link it up again

5.Change a new battery

6.Go to the maintenance area

7.Go to the maintenance area

Battery cannot be recharged

1.Socket connector of the battery

has fallen off

2.There’s no power

1.Link it up again

2.Plug it in

Short flight mileage

1.Battery off

2.Battery is old

1.Recharging the battery

2.Change a new battery

There’s slight sound and heat

when recharging

1.This belongs to normal

chemical reaction

1.It’s normal

Low speed

1.Battery is old

2.Dead battery

3.Overload

4.Pavement irregularity

1.Change a new battery

2.Recharging the battery

3.Reduce weight bearing to below

30kg

4.Ride on smooth-riding surface

Gearbox has noise

1.Gear is broken

1.Repair it in maintenance point

Car is shaking when progressing

1.Connector cable for lens motor

contact poorly

2.There’s dead spot on the motor

1.Reconnect it

2.Repair it in maintenance point

Battery indicating light is not

1.Body power is not on

2.Battery is dead

1.Turn it on

2.Recharging the battery

 After the regular service of the product, adults should regularly (suggest once

two weeks) check the main items, including storage battery, charging device,

wires, outer skin, circuit changer and switching valve. Clamp devices should be

checked to see whether is loose. When there ’ s hidden danger, the product

should be stopped being used until restored.

 The vehicle should be cleaned by slightly wet (no water drop) soft cotton. Also

can be polished by non-wax furniture in order to make the surface bright and

clean. Do not use chemical dissolvent to wipe the plastic part of the toy to avoid

being dissolved. The car cannot be cleaned by soap and water since water will

damage the motor and storage battery, causing short pass of the electro-circuit

system.

 After using for a period of time,please use lubricating oil to lubricate the iron

part in order not to get rusty.

 The car should be kept away from high temperature and moistness ,since the

plastic parts might melt.When charging,please keep it away from inflammable

materials so that fire will not occur.

 After using,please recharge it in time.Recharging should be operated by

adults.If the car will not be used for a long time or be stored up,it has to be

fully-recharged before storage.Then recharge it once every month to lengthen

its life.

 When stop or not using for a long time ,please cut off the power .All the circuit

changers should be switched to “STOP”or “OFF” .The structure and wire

system cannot be altered without authorization.Maintenance and replacement

of crucial parts should be supervised by professionals.

 In areas where power supply is unstable,installing power regulator is highly

recommended to protect the storage battery when recharging.

 Do not use safety wires not accord with the product.

working

Car cannot be stopped 1.Electrical damage 1.Repair it in maintenance point

Maintenance：

Play

Active

outdoor toys for kids

Thank you for choosing a PlayActive product.

We hope your child will endure many years of fun

with this item. If you require any trouble shooting

assistance or help on assembly please view our

tutorial videos available on our website.

www.playactive.net

WARNING!

Do not use this vehicle indoors. Using this

vehicle in confined areas may cause the

vehicle's motors to over load.

If you require any further assistance please contact the outlet you

purchased this item from.