DOMO Steam Generator Iron User Manual

Steam

Generator Iron

Operation Instructions

AS SEEN

ON TV

Instructions.indd 1 14/12/06 09:16:59

Steam

Generator Iron

Operation Instructions

Instructions.indd 2-3 14/12/06 09:17:21

1. Make sure that the applied voltage is

same as the rated voltage, and the
socket has effective ground
connection.

2. Do not use if the unit is damaged in

any way.

3. Take off the protective film or label

(if any) on the soleplate and clean
it with soft towel before using.

4. Use distilled water. Do not fill in with

any other liquid except water.

5. Some smoke might come out from

the soleplate during first using. It is
normal and will stop after a short time.

6. When using the steam function, it

may take 30 seconds for the steam
to appear.

7. Do not touch the soleplate, water or

steam while in operation and some
time after use.

8. Keep the cord away from the

soleplate.

9. Do not immerse the iron into any

liquid.

10. Turn the temperature control knob

to “MIN” before you plug or unplug
the iron.

11. Do not direct steam at people.

12. Do not leave the unit unattended

when connected to the power supply.
When you leave it, even for a short
time: a) Turn off the steam; b) Put
the iron unit on the heat-proof board,

not within the reach of children & c)
Unplug the unit.

13. In the case of malfunction, send it to a

qualified person for repair. Do not
attempt to repair it yourself.

14. This iron is for household use only.

15. Ensure that the unit is not plugged

in when filling the water reservoir.

16. The filling aperture must not be

opened during use.

17. If the supply cord is damaged, it

must be replaced by the manufacture,
its service agent or similarly qualified
persons in order to avoid a hazard.

18. Ensure the water in the tank is above

the “MIN” level before using the steam
function.

Cautions

9

10

11

1

7

8

2

3 4

5

6

Number Part Function

01 Heat-Proof Board To rest the iron unit
02 Water Inlet with Cover Fill water into the tank
03 Steam Button Operates the steam function
04 Automatic Steam Button Press down to have non-stop steam & press up

to stop it

05 Temperature Control Dial To adjust the temperature
06 Heating Indication Light Heating indicator
07 Power Indication Light Power on indicator
08 Steam-Adjusting Button Adjustable steam or dry ironing
09 Anti-Calc This inner anti-calc device works automatically

to reduce the amount of scale produced

10 Water Tank Store up to 1.2 litres of water – check the

level indicator

11 Soleplate Non-stick coating soleplate

Thank-you for purchasing
the JML Steam Generator Iron.

In order to make the best use of this
iron and use it safely, please read these
instructions carefully before use and keep
for future reference.

Parts List and Function

Fig 1

Instructions.indd 4-5 14/12/06 09:18:01

Filling with water:

Open the Water Inlet Cover (2), fill with
water and close the cover. Nb. do not fill
past the “MAX” position.

Setting the temperature:

Follow the ironing instructions on the
garments.

If there are no ironing instruction on the
garments our chart (fig 2) may be used for
guidance.

1. Ensure the iron is correctly positioned

on the Heat-proof Board (1).

2. Plug in the iron, both the Power

Indication Light (7) & Heating
Indication Light (6) will light up.

3. Turn the Temperature Control Knob

(5) to the required setting.

4. Once the Heating Indication Light

(6) switches off, you may begin
ironing. Nb It will take approx. Two
minutes to reach the required
temperature.

Operation

Steam ironing:

1. Make sure there is sufficient water
in the tank.

2. Turn the Temperature Control Knob
(5) to the position you need.

3. Once the Heating Indication Light
(6) turns on & then off, turn the
Steam-adjusting Button (8) to the
suitable position. Press the Steam
Button (3) or the Manual Steam
Button (4) to start steam ironing.

Note:

During the steam process, small
amount of water may be ejected from
the soleplate. This can be avoided by
reducing the steam output at the steam
control dial at the base.

Dry ironing:

When dry ironing, turn the Steam­adjusting Button (8) to “MIN” and turn the
Temperature Control Knob (5) to proper
position according to different materials of
the clothes.

Caution: symbol means the garment is not suitable to be ironed.

Symbol Material Temp. setting Steam control dial setting

Man-made fibre,

Artificial silk, Nylon, silk • Lowest ...................................

Wool • • Medium •/• •
Cotton Linen • • • Highest •/• •/• • •

John Mills Limited

JML House Regis Road

London NW5 3EG

Tel: [phone]

Fax: [phone]

[e-mail]

www.jmldirect.com

Calc Clean:

Dirty or brown water may be emitted from
the soleplate. This may happen as a result
of using hard or tap water which allows a
production of scale inside the water tank.

The unit can be cleaned in the
following way:

1. Unplug the unit, fill the water tank
with distilled water. Close the inlet
cover. Hold the water tank with both
hands and shake well.

2. Open the water tank inlet cover and
pour the water away.

3. Repeat steps 1 and 2 a few times to
clean well.

4. On the iron, turn the temperature
control knob to “MIN”, turn the steam
control knob to “MAX”. While holding
the iron with the soleplate pointing
away from you plug the iron in and
press the steam button down
immediately. This will allow the water
pumped to go through the steam
chamber and clean it well.

5. Clean the soleplate with a soft cloth
after all the dirty water has come out.

Cleaning and storage:

1. Unplug the unit and allow it to cool
down completely.

2. Clean the soleplate with damp
soft towel.

3. Periodically fill the tank with
water, shake and pour the water away.

4. Store the iron in a cool dry place
beyond the reach of children

Specification:
Rated voltage AC 220-240V 50Hz
Rated power 2600W
Insulation Class Electrical Appliance

Class I.

Instructions.indd 6-7 14/12/06 09:18:02

Instructions.indd 8 14/12/06 09:19:31