Dome DMWV1 Installation Manual
WATER MAIN SHUT-OFF
Thank you for purchasing the Dome Z-Wave Water Main Shut-O, which works with
your Z-Wave Certied Controller to let you control your water main while on vacation,
or have it automatically shut o in case of leaks or other emergencies.
LED Indicator
Control Arm
Figure 1
Open/Close
Button
Motor Assembly
Mounting Bracket
Including/Connecting into the Z-Wave Network:
1. For proper inclusion, bring the Water Main Shut-O to the nal location
where it will be used. *
CAUTION
Upon inclusion, the motor will engage and start turning automatically. To avoid serious injury, keep your ngers and
hands clear of the CONTROL ARM and its path, only gripping the unit rmly by either the MOUNTING BRACKET or the
top of the MOTOR ASSEMBLY.
2. Follow the instructions for your Z-Wave controller to enter inclusion mode.
3. Make sure the Water Main Shut-O is powered on, and when prompted by
your controller, press the “open/close” button quickly 3 times in a row. The
LED will stop blinking and stay on continuously upon successful inclusion.
*For non Z-Wave Plus networks, please consult the owner’s manual for your primary controller to determine the best method and location for adding
the Water Main Shut-O to your Z-Wave network.
Installation:
The Water Main Shut-O can be installed on
any preexisting ½” to 1 ½” brass ball valve, at
least 5” away from any walls or other obstructions. Examine Figure 3 and make sure there
is enough room in your plumbing installation to
accommodate the Shut-O.
1. Make sure the valve is comfortably usable
by hand before continuing further.
2. Unscrew the screws on both HOSE CLAMPS
completely so their ends are free, insert
both of them into the MOUNTING BRACKET,
and let them hang loosely.
3. Remove the protective lm covering the
CONTROL ARM screws and spread the CONTROL ARM.
Control
Arm
4. Make sure both the ball valve and the Water
Main Shut-O are in the “open” position (where
the handle is inline with the pipe, not at a right
angle to it,) and slide the CONTROL ARM around
the valve’s handle (g 4.)
Valve
Handle
5. Loosely tighen the hose clamps around the
pipe on the opposite side of the valve handle so it
remains movable (g 3.)
Figure 4
5”+
Hose Clamps
5”
Figure 3
(continued on next page)
6. Position the bolt of the Water
Main Shut-O DIRECTLY above
the bolt of the ball valve, and
tighten the hose clamps until
the Shut-O is completely
secure (g 5.)
It is absolutely critical that the
axes for both the valve and Water
Main Shut-O are aligned. Improper installation will result in
unreliable performance. Examine Figure 5 for more details and
please visit www.domeha.com/
support if you require further
assistance.
7. Squeeze the CONTROL ARM
closed around the valve handle
and secure it tightly with the
four screws previously covered
by the protective lm.
8. To test for proper installation,
power up the device and press
the OPEN/CLOSE button. The
motor will engage and your
valve will close.
Figure 5
Centers are aligned
Override Operation
The Water Main Shuto can be operated
manually in the event of a power outage,
loss of communication with your Z-Wave
Hub, or some other emergency. Follow
these instructions to manually operate the
Shut-O:
1. Unplug the power from your device.
2. Locate the MOTOR CLUTCH on the
Motor Clutch
underside of your device (g 6,) and pull
it outward by the keychain ring. The
Figure 6
CONTROL ARM will disengage from the
motor and move freely.
Removing the Water Main Shut-O From Your System
1. Follow the instructions for your Z-Wave certied Controller to enter exclusion
mode.
2. When prompted, press the “open/close” button on the Shut-O quickly 3 times
in a row.
Resetting Your Water Main Shut-O to Factory Settings
1. Press and hold the open/close button for at least 10 seconds then release. The
Shut-O’s memory will be erased to factory settings. A ashing light indicates a
successful factory reset. Beware that resetting your device will disconnect it from
your system. Only do this if the controller is missing or otherwise unreachable!
NEED HELP? CONTACT DOME CUSTOMER SERVICE
If you have questions, our trained Customer Service Department is happy to assist you 24 hours a day, 7 days
a week. Contact Dome Customer Service as follows: • In North America dial: 1-855-249-1754 • Email Dome
at support@domeHA.com
DO NOT RETURN THIS PRODUCT TO THE STORE OR WEBSITE FROM WHICH IT WAS PURCHASED
If you believe the product is defective, has a missing or broken part or are having diculty with it please
contact Dome as listed above for a quick and ecient solution to the problem.
Legal Notices: This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of the following
measures: Reorient or relocate the receiving antenna; increase the separation between the equipment and
the receiver; connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected. Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
WARRANTY INFORMATION
Elexa Consumer Products, Inc. (”ECP”) warrants to the
original retail purchaser (”Purchaser”) that the DOME Window/Door sensor (the “Product”) will be free of defects in
materials or workmanship under use for one (1) year from
the date of purchase (the “Warranty period”).
For the Purchaser only, if the Product fails to perform
as specied during the Warranty Period due to defective
parts or faulty workmanship, ECP will repair or replace
the defective or damaged parts of the Product. Normal
wear and tear is not covered nor is abnormal use, misuse,
mishandling, faulty installation, improper shipping, damage caused by disasters such as re, ood or earthquake,
neglect, accident or tampering. This warranty covers only
normal use in the United States or Canada.
To obtain warranty service during the Warranty Period, call
Dome Customer Service (1-855-249-1754) or email: support@domeHA.com for instructions on sending damaged
parts and documentation for a Return Material Authorization (RMA). Products returned to ECP for repair or replacement without authorization will be returned at the sender’s
expense. All warranty claims must be accompanied by a
legible copy of the original receipt showing date and details
of purchase. The RMA number must be clearly written on
the side of the shipping container in which you return the
Product or defective parts. Unless otherwise instructed
by ECP, the Product must be sent Freight pre-paid to the
following address:
Elexa Consumer Products, c/o Promac,
1153 Timber Dr., Elgin, IL 60123
ECP will repair or replace the defective parts and return
them at ECP’s cost by a shipping method selected by ECP.
When contacting ECP to obtain an RMA, Purchaser may
request expedited return shipping at Purchaser’s expense.
THIS WARRANTY IS NOT TRANSFERABLE, AND, TO THE
MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW IS
IN LIEU OF ALL OTHER WARRANTIES, REPRESENTATIONS
AND CONDITIONS, EXPRESSED OR IMPLIED, STATUTORY OR OTHERWISE, INCLUDING BUT NOT LIMITED
TO THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. NO OTHER
PERSON OR REPRESENTATIVE IS AUTHORIZED TO MAKE
ANY OTHER WARRANTY ON BEHALF OF ECP OR ASSUME
FOR ECP ANY OTHER LIABILITY IN CONNECTION WITH
THE SALE OF THIS PRODUCT. IN NO EVENT WILL ECP
BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT
LIMITED TO INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR INABILITY TO
USE THE PRODUCT, INCLUDING DAMAGES DUE TO
ECP’S NEGLIGENCE.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE AND COUNTRY
TO COUNTRY.
©2016 Elexa Consumer Products, Inc.
2275 Half Day Rd., Suite 333
Bannockburn, IL 60015
www.domeHA.com #2ACC6GR-105
Loading...