Page 1
Thank you for your purchase of the Transmitter Solutions Dolphin
wireless keypad. The KEYTS433RC will accomodate one 4 digit PIN
to activate a signal transmission and can control up to four devices.
Package contains:
Keypad
9 volt battery
2 screws + wall anchors
Keypad instructions
Please follow the detailed instructions below in order to set up the Dolphin keypad to
operate with your garage door opener or receiver.
2. OPERATIONAL FEATURES
Keypad Instructions
Dolphin Wireless Garage Door Keypad
433 MHz
Product # KEYTS433RC
Pressing any key illuminates the keypad for 5 seconds.
A "buzzer" indicates each button depression.
After 20 incorrect key entries, the keypad will “lock up” for 40 seconds.
If the battery is low the single LED flashes rapidly for 5 seconds, indicating it is time
to replace the battery.
After you have entered a valid code, the keypad LED will flash during the 5 second
"time out" period. During the “time out” period you may press any key and the
keypad will send another signal to your receiver each time you press a key.
The key resets your entry. If you make a mistake while entering your PIN,
pressing the key resets your entry so you can start over.
HINT: If you always begin your PIN with the you will reduce the likelihood of
faulty operation
Page 2
3
• The transmitter module built into the KEYTS433RC is a 4-channel, rolling code
transmitter.
• As each transmitter has a unique serial number, no further action by the user is
required outside of programming the receiver to recognize the rolling code signal.
• Refer to your receiver’s instruction for how to program the keypad signal into
your receiver.
• When the receiver instructions indicate the need to press the transmitter button,
you will need to enter your PIN into the keypad to initiate a transmission.
Hint: When the correct PIN is entered, the keypad will blink 3 times. An incorrect PIN
will result in a 1-second beep.
RESETTING THE KEYPAD TO THE DEFAULT PIN
1. Disconnect the battery
2. Hold any key on the keypad while reconnecting the battery
3. Continue to hold the key for 5 seconds then release
4. The default pin should now be 1,2,3,4
PROGRAMMING THE KEYTS433RC
Default PIN: 1 2 3 4
Changing the PIN
Accessing a
specific channel
#, #, PIN: 1 2 3 4, New PIN: __ __ __ __ , Channel:1-4
#, PIN: __ __ __ __, Channel:1-4
Programming the keypad to PIN:5555
Step 1: #, #,
Step 2: 1 2 3 4 (old pin)
Step 3: 5 5 5 5 (new pin)
Step 4: 1 (channel 1)
Entering simply 5 5 5 5 will access the channel
programmed. In our example, 5 5 5 5 will access channel 1.
Use this sequence when accessing a different
channel is desired for multi-channel receivers.
Example:
#, 5 5 5 5, 2 accesses channel 2
#, 5 5 5 5, 3 accesses channel 3
#, 5 5 5 5, 4 accesses channel 4
Page 3
Position the keypad on the garage door frame with the provided
screws.
Lift up the conver and insert the long screw above the keypad in
the slot provided (a).
Remove the battery cover and insert the second long screw in
the lower slot (b).
Replace the battery cover.
4
cover
6
7
The keypad is approved by the FCC and it complies with Part 15 of the FCC Rules. Its
operation is subject to the following 2 conditions:
1. This device may not cause harmful interference.
2. The device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC ID: SU7KEYDOL433RC
The warranty period of Transmitter Solutions keypads is twenty-four (24) months. This
warranty shall begin on the date the keypad is manufactured. During the warranty period, the
product will be repaired or replaced (at the sole discretion of Transmitter Solutions) if the
product does not operate correctly due to a defective component. This warranty does not
extend to (a) the keypad case, which can be damaged by conditions outside the control of
Transmitter Solutions, or (b) battery life of the keypad. This warranty is further limited by the
following disclaimer of warranty and liability:
EXCEPT AS SET FORTH ABOVE, TRANSMITTER SOLUTIONS MAKES NO WARRANTIES REGARDING THE
GOODS, EXPRESS OR IMPLIED, INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS
FOR A PARTICULAR PURPOSE. BUYER MAKES NO RELIANCE ON ANY REPRESENTATION OF TRANSMITTER
SOLUTIONS, EXPRESS OR IMPLIED, WITH REGARD TO THE GOODS AND ACCEPTS THEM “AS-IS/WHERE-IS”.
TRANSMITTER SOLUTIONS SELLS THE GOODS TO BUYER ON CONDITION THAT TRANSMITTER SOLUTIONS
WILL HAVE NO LIABILITY OF ANY KIND AS A RESULT OF THE SALE. BUYER AGREES THAT TRANSMITTER
SOLUTIONS SHALL HAVE NO LIABILITY FOR DAMAGES OF ANY KIND, WHETHER DIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, INCLUDING INJURIES TO PERSONS OR PROPERTY, TO BUYER, ITS
EMPLOYEES OR AGENTS, AS A RESULT OF THE SALE. BUYER ALSO AGREES TO HOLD TRANSMITTER
SOLUTIONS HARMLESS FROM ANY CLAIMS BUYER, OR ANY THIRD PARTY, MAY HAVE AS A RESULT OF
BUYER’S USE OR DISPOSAL OF THE GOODS. BUYER HAS READ THIS DISCLAIMER AND AGREES WITH ITS
TERMS IN CONSIDERATION OF RECEIVING THE GOODS.
DO NOT let children use the keypad without adult supervision. Children can injure
themselves, or others, if left unsupervised. Make sure all the required safety devices are
installed before operating any door.
If this transmitter triggers other doors in your neighborhood, change all your transmitters
and receivers to a new code setting.
5
Page 4
Other Dolphin wireless garage door keypads by Transmitter Solutions:
KEYTS300/310 - 300 MHz, 310 MHz dual frequency
KEYTS390 - 390 MHz, 9 dip switch
Loading...