DOLKWP300318
Dual Frequency 300/318 MHz Keypad
STEP 1: Set Jumper S1
Determine the operating frequency you
will use on your keypad installation. This
keypad can operate at either 300 MHz
or 318 MHz. At 300 MHz the keypad is
compatible with all 300 MHz receivers
with 10 dip switches. At 318 MHz the
keypad is compatible all 318 MHz
receivers with 9 dip switches.
(see Figure 1)
300 MHz
Figure 1
S1
OFF
ON
1
4 Sec
2
2 Sec
3
1 Sec
3 State/9 PORT 2 State/10 PORT
4
S2 Function Config
300Mhz
318Mhz
S1
S1 Frequency Selection
ON
S2
1 2 3 4
DIP
10
jumper
in place
318 MHz
GND
CON1
GND OP VIN
S1
STEP 2: Set Jumper 4 on S2
• 300 MHz (10 dip switches) - Jumper set to OFF (in the DOWN position)
ON
S2
1 2 3 4
• 318 MHz (9 trinary dip switches) - Jumper set to ON (in the UP position)
ON
S2
1 2 3 4
STEP 3: Set the DIP switches to match the Receiver
Set the DIP switches of the keypad to “+” for ON or CLOSE, and “-” for OFF or
OPEN. Note: Do not use the center position.
DIP
10
300 MHz
(10 dip switch)
DIP
318 MHz
(9 dip switch)
10
not used
STEP 4: Programming the Master Code
1. Press
2. Enter the “Master Code” (default is )
3. Press the button
4. Enter for change code
5. Enter for “Master Code”
6. Enter the new “Master Code” (Must be 4 digits)
7. Press the button. The multi-color status LED flashes Green 3 times meaning
the code is accepted. If the multi-color status LED flashes 3 times Red, the
steps need to be repeated.
*
1
0 0
1
432
*
*
STEP 5: Programming the User Entry Code
1. Press
2. Enter the “Master Code” (default is )
3. Press the button
4. Enter for change code
5. Enter for the number of user code (eg. “03” for the third user code, etc).
6. Enter the new “User Enter Code” (Must be 4 digits)
7. Press the button. The multi-color status LED flashes Green 3 times meaning
the code is accepted. If the multi-color status LED flashes 3 times Red, the
steps need to be repeated.
*
1
0 1
*
1
432
STEP 6: Deleting the programmed User Entry Code
1. Press
2. Enter the “Master Code” (default is )
3. Press the button
4. Enter for delete code
5. Enter for the number of user code (eg. “03” for the third user code, etc).
6. Press the button. The multi-color status LED flashes Green 3 times meaning
the code is accepted. If the multi-color status LED flashes 3 times Red, the
steps need to be repeated.
*
2
0 1
*
1
432
STEP 7: Activating the Keypad
1. Press
2. Enter your programmed usercode.
DOLKWP300318 OPERATION
Return to Default Settings
1. Disconnect the power by removing the battery.
2. Press the , , and keys simultaneously.
3. Re-connect the battery to power up the keypad.
4. Release the , , and keys.
Note: The keypad is returned to the default “Master Code” . And all User
Entry Codes are deleted.
Multi-color status LED
ORANGE - Key depress
GREEN - Code was entered correctly and the keypad is transmitting
GREEN - Programming Mode
RED - (Flashing 3 times) Error was made in either programming mode or in
code entry.
1 4 7
1 4 7
1 432
RF Transmit Time Setting on S2
RF transmit 1 seconds
RF transmit 2 seconds
RF transmit 3 seconds
ON
1 2 3 4
DOWN (300 MHz)
UP (318 MHz)
S2
ON
1
2
3
4
300Mhz
318Mhz
S1
S1 Frequency Selection
DIP
10
OFF
4 Sec
2 Sec
1 Sec
3 State/9 PORT 2 State/10 PORT
S2 Function Config
ON
1 2 3 4
S2
RF transmit 4 seconds
GND
RF transmit 5 seconds
CON1
GND OP VIN
S2 Function Config
RF transmit 6 seconds
RF transmit 7 seconds
ON
1
4 Sec
2
2 Sec
3
1 Sec
3 State/9 PORT 2 State/10 PORT
4
OFF
RF transmit 0 seconds
DIRECT HARD WIRE:
NOTE: Remove 9V battery
GROUND
RELAY
POSITIVE
WARRANTY:
The warranty period of this product is 24 months, beginning from the
manufacturing date. During this period, if the product does not operate correctly,
due to a defective component, the product will be repaired or replaced at the sole
discretion of Transmitter Solutions. This warranty does not extend to the product
casing which can be damaged by conditions outside of the control of Transmitter
Solutions.
Loading...