Page 1
Thank you for your purchase of the Transmitter Solutions Dolphin
wireless keypad. The DOLGDO315390 will accomodate one 4 digit PIN
to activate a signal transmission.
Package contains:
Keypad
9 volt battery
2 screws + wall anchors
Keypad instructions
Please follow the detailed instructions below in order to set up the Dolphin keypad to
operate with your garage door opener or receiver.
2. OPERATIONAL FEATURES
Keypad Instructions
Dolphin Wireless Garage Door Keypad
Dual Frequency 315/390 MHz
Product # DOLGDO315390
Pressing any key illuminates the keypad for 5 seconds.
A "buzzer" indicates each button depression.
After 20 incorrect key entries, the keypad will “lock up” for 40 seconds.
If the battery is low the single LED flashes rapidly for 5 seconds, indicating it is
time to replace the battery.
After you have entered a valid code, the keypad LED will flash during the 5 second
"time out" period. During the “time out” period you may press any key and the
keypad will send another signal to your receiver each time you press a key.
The key resets your entry. If you make a mistake while entering your PIN,
pressing the key resets your entry so you can start over.
HINT: If you always begin your PIN with the you will reduce the likelihood of
faulty operation
Page 2
S2
S2
390 MHz
315 MHz
Back of
Keypad
a. Remove the access door on the top back of the keypad by sliding the door
in the direction of the arrow. (see Figure 1)
b. Locate the frequency switches on the top of the electronic board located
inside of the access door. (see Figure 2)
3. SET FREQUENCY JUMPER
a. Determine the operating frequency you will use on your keypad installation.
This keypad can operate at either 315 MHz or 390 MHz. At 315 MHz the keypad is
compatible with all 315 MHz receivers with 9 dip switches. At 390 MHz the keypad
is compatible all 390 MHz receivers with 9 dip switches. (see S2 on Figure 3)
3
Figure 3
Figure 1
Figure 2
jumper
in place
access
door
S2
S2
S1
S2 315MHZ 390MHZ
1-2 2-3
DIP
390 MHz
315 MHz
Page 3
4. SET DIP SWITCHES
a. Set the DIP switches of the keypad to match the DIP switch settings of the
receiver, or a functioning transmitter. (see Figure 4)
b. Enter then the 4 digit PIN on the keypad, and then press # to activate the
c. To change the 4 digit PIN (example)
receiver. If you just purchased the keypad, the factory default 4-digit PIN is 1234.
So please enter 1-2-3-4 #. If the receiver does not operate, reverse the keypad
DIP switches, and re-enter 1-2-3-4 #.
TIP: When you enter the correct code followed by #, the keypad LEDs flash slowly
for 5 seconds. If you enter an incorrect code, the keypad LED will glow steady for
5 seconds.
TIP: When you have entered the programming mode of # # the small LED glows
a steady red. When you complete the change of the PIN the small LED flashes
twice quickly.
To reset the keypad to the factory default code, remove the 9 volt battery and
depress and hold any key on the keypad, then reinstall the battery. Continue holding
the key down for 5 seconds and then release the key. The keypad is now reset to
the factory defaults.
Position the keypad on the garage door frame with the
provided screws.
Lift up the conver and insert the long screw above the keypad
in the slot provided (a).
Remove the battery cover and insert the second long screw
in the lower slot (b).
Replace the battery cover.
# # 1-2-3-4 1-3-5-7 #
(Old Pin)
followed within 5 seconds by (New PIN)
pin must be four digits
Back
Opening
4
3
Figure 4
dip
switches
cover
S2
S1
S2 315MHZ 390MHZ
1-2 2-3
DIP
Page 4
Other Dolphin wireless garage door keypads by Transmitter Solutions:
DOLGDO300310 - 300/310 MHz 8/10 dip switch
DOLGDO433RC - 433 MHz 4 channel, long range, rolling code
6
7
The keypad is approved by the FCC and it complies with Part 15 of the FCC Rules. Its
operation is subject to the following 2 conditions:
1. This device may not cause harmful interference.
2. The device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
FCC ID: SU7DOLGDO315390
The warranty period of this product is 24 months, beginning from the manufacturing
date. During this period, if the product does not operate correctly, due to a defective
component, the product will be repaired or replaced at the sole discretion of
Transmitter Solutions. This warranty does not extend to the product casing which can
be damaged by conditions outside of the control of Transmitter Solutions.
DO NOT let children use the keypad without adult supervision. Children can injure
themselves, or others, if left unsupervised. Make sure all the required safety devices are
installed before operating any door.
If this transmitter triggers other doors in your neighborhood, change all your transmitters
and receivers to a new code setting.
5
Loading...