Page 1
INSTALLATION AND MAINTENANCE GUIDE
BC634
BEHIND FREE TOUCH FREE
SOAP DISPENSER
Saving soap, saving power, promoting hygiene
Important:
Read carefully before installing product
Page 2
2 | Dolphin Blue | BC 634
3 Technical Data
4 Pre-Installation Information
5 Pack Contents
6-8 Installation
9 Filling The Soap Tank
10 Settings Adjustment with a Remote Control
11 Batteries Replacement
12 Maintenance
Care And Cleaning Of Chrome And Special Finishes
13 Spare Parts List
14 Warranty
15 Trouble Shooting
INDEX
Page 3
BC 634 | Dolphin Blue | 3
TECHNICAL DATA
Behind mirror Soap Dispenser BC 634B
Behind mirror Soap Dispenser BC 634E
Capacity: 1 Litre \ 33.8 oz.
Power Supply: IP 67 Battery Box for 6xD Alkaline batteries \ Transformer
Soap viscosity: 100 – 3800 cPs
Standard discharge: 0.8cc, Adjustable
Sensor range: 30-100 mm +/- 10 mm (Adjustable by remote control).
Page 4
4 | Dolphin Blue | BC 634
PRE INSTALLATION INFORMATION
Check contents
Separate all parts from the packaging and check each part with the “Pack contents”
section.
Make sure all parts are accounted for before discarding any packaging material.
If any parts are missing, do not attempt to install your touch free soap dispenser
until you obtain the missing parts.
Warnings
1) To avoid reflection problems keep a distance of more than 300 mm. between the
sink and the spout.
2) This tap model, with an infrared sensor pointing down, is not intended to be used
together with a sink of a reflective
material such as stainless steel.
3) If a sink strainer is straight below the tap sensor, use a strainer with a non reflective
finish (do not use a chrome plated one).
4)To prevent reflection problems, it is recommended to keep a minimum distance
of 1.50 meters between the soap dispenser and any other objects.
Important: Pay attention that the
dimensions of the mirror
compartment fits the dimensions of
the Behind Mirror Soap Dispenser
plate.
Page 5
BC 634 | Dolphin Blue | 5
Familiarise yourself with the part names and confirm that the parts are
included.
PACK CONTENTS
4 screws up to 5mm
(not supplied)
Product assembly containing: Pump
with bottle support,plate with spout
and soap tank
IP 67 Battery
box for 6 x D
alkaline batteries
Transformer
Page 6
6 | Dolphin Blue | BC 634
INSTALLATION
Step 1 : Preparation for
installation
Cut a hole in the bottom of the
mirror compartment for the soap
dispenser sensor and spout both.
The recommended hole size
should be 30x50 mm.
Step 2 : Installing the soap
dispenser
1. Remove the protective sticker
covering the sensor.
2. Place the soap dispenser
assembly inside the mirror
compartment with the spout
sticking out of the hole.
Page 7
BC 634 | Dolphin Blue | 7
INSTALLATION
3. Secure the plate to the
wall with 4 screws (not
supplied).
Step 3 : Connecting the
power source
Make sure that the 4 contacts
connector is connected
properly so that the white
o-ring is not visible.
Pay attention: If the 4
contacts connectors will not
be connected properly, the
motor will work continuously.
O-ring visible – not connected properly
Connected properly so that only the groves
are visible
Page 8
8 | Dolphin Blue | BC 634
For battery versions:
Install the battery box at the wall
in the mirror compartment and
connect the battery connector.
For transformer versions:
Plug the transformer into the
electricity socket and make sure
the transformer connector is
connected.
Wait about 10 seconds before
you put your hands within the
sensor range.
INSTALLATION
Page 9
BC 634 | Dolphin Blue | 9
FILLING THE SOAP TANK
1. Unscrew the
soap tank from the
pump assembly.
3. Insert the bottle
with the tube
inside the bottle
support.
5. Press the refill
button located at
the back of the
pump assembly
until soap starts
coming out of the
soap dispenser
spout. This
operation can also
be done using the
soap dispenser
remote control
Refill function.
2. Fill in the liquid
soap up to the
top line.
4. Screw the soap
tank back to the
pump assembly.
Make sure the
tank is secured
firmly in place.
Note: Once the
soap in the soap
tank has reached
the bottom line
the soap tank
should be refilled.
To refill the soap
tank please refer
to steps 1-5.
Page 10
10 | Dolphin Blue | BC 634
If desired, use the remote control to adjust the soap
dispenser settings. Hold the remote control straight in
front of the sensor in a distance of about 4-6” (10-
15cm).
Attention: Holding the soap dispenser remote
control out of the recommended range (too close or
too far)may interfere with the remote’s activation.
Choose the function you want to adjust by pressing
on the function button as following:
1 Soap Quantity
The 1-4 drop keys allow the user to choose the
desired soap quantity.
Indication: continues blink of the red light in the sensor eye.
* The exact soap dosage depends on the soap viscosity.
1 0.2 to 0.4 2 0.7 to 0.9 3 1.2 to 1.6 4 2.1 to 2.3
2. ADJ
This function allows coming back to soap quantity factory settings. Press the ADJ
button. Indication: 2 blinks of the red light in the sensor eye.
3 Temporary Off Function
This function is ideal to perform any kind of activity in front of the sensor without
operating the system (for example, cleaning). The soap dispenser will remain shut for
1 minute when this button is pressed once. To cancel this function and to return to
normal operation press the On/Off button again or wait 1 minute.
Indication: OFF – 2 fast blinks, ON – 4 fast blinks
4 Refill The Soap Tank
Once the soap tank has been refiled, press the FILL button. The pump would work
for one minute in order for the soap to start coming out of the soap dispenser
spout. To stop this activity press the FILL button again.
SETTINGS ADJUSTMENT WITH
A REMOTE CONTROL
Page 11
BC 634 | Dolphin Blue | 11
Battery models only
When the battery weakens, the red indicator light will blink at a constant rate when
the user’s hands are within the sensor range. The battery must be replaced within
two weeks.
To replace the battery in battery models:
1. Carefully open the battery box place within the mirror compartment, using 2.5
mm Allen key
2. Remove the old batteries
3. Replace the used batteries with new D batteries
NOTE: Do not mix used batteries with new ones.
BATTERY REPLACEMENT
Important: Spent batteries should not be disposed of with normal
household waste. Contact your local authority for information on
waste disposal and recycling.
Page 12
12 | Dolphin Blue | BC 634
Care and cleaning of chrome and special finishes
DO NOT use steel wool or cleansing agents containing alcohol, acid, abrasives, or
the like. Use of any prohibited cleaning or maintenance products or substances
could damage the surface of the soap dispenser. For surface cleaning use ONLY
soap and water, then wipe dry with a clean cloth or towel. When cleaning
bathroom tiles, the soap dispenser should be protected from any splattering of
harsh cleansers.
MAINTENANCE
Page 13
BC 634 | Dolphin Blue | 13
Part Name Part Code
Sensor kit BC 07220230
Soap tank 1 L BC 07100020
Transformer BC 06522042
Soap dispenser Pump assembly BC 07222001
Remote control BC 07100008
IP67 transformer box BC 06530021
IP 67 Battery Box for 6xd alkaline batteries BC 06530041
Bottle support 1 L BC 07120175
Soap dispenser spout assembly BC 07271023
SPARE PARTS LIST
Page 14
14 | Dolphin Blue | BC 634
Filter cleaning instructions
The tap is provided with one stainless steel filter preventing foreign particles to
enter the lines. If the water flow has decreased, this may be because the filter is
clogged. The filter can be cleaned as follows:
1. Shut-off the water shut off valve.
2. Disconnect the water supply inlet from the adapter at the solenoid valve
housing.
3. Remove the filter from the adapter and wash it under running water.
4. Reassemble the parts.
5. Reconnect the solenoid valve housing and restore the incoming water supply.
6. Make sure that there is no water leakage.
Care and cleaning of chrome and special finishes
DO NOT use steel wool or cleansing agents containing alcohol, acid, abrasives, or
the like. Use of any prohibited cleaning or maintenance products or substances
could damage the surface of the tap. For surface cleaning of tap us ONLY soap and
water, then wipe dry with clean cloth or towel. When cleaning bathroom tile, the
taps should be protected from any splattering of harsh cleansers.
LIMITED WARRANTY
Page 15
BC 634 | Dolphin Blue | 15
TROUBLE SHOOTING
PROBLEM INDICATOR CAUSE SOLUTION
Replace batteries
Increase the range with remote
Decrease the range with remote
Replace batteries
Decrease the range or eliminate
cause of reflection
Low batteries
Range is too short
Range is too long ie tap
has gone into security mode
Batteries are completely used up
Sensor is picking up reflections
ie tap has gone into security mode
Connectors between the
electronic unit and the solonoid
are disconnected
Debris or scale in solonoid
The central orifice in the
diaphragm is plugged or the
diaphragm is torn
The water supply pressure is
higher than 8 bars
Debris or scale in diaphragm
Sensor is dirty or covered
Sensor is picking up reflections
from the washbasin or another
object
Filter or aerator is clogged
Sensor flashes
continuously when
user’s hands are
within the sensor’s
range
Red light in the
sensor does not flash
once when user’s
hands are within the
sensor’s range
Red light in the
sensor flashes once
when user’s hands are
within the sensor’s
range
Sensor flashes once
when user’s hands are
within the sensor’s
range
Red light in the
sensor does not flash
when user’s hands are
within the sensor’s
range
No water
comes out
of the tap
Water flow
from spout
does not
stop
Water flow
diminished
Connect the electronic unit
connectors to the solonoid
Unscrew solonoid, pull out the
plunger and the spring from the
solonoide and clean them. Use
scale remover material if needed.
When replacing the plunger,please
make sure that the spring is in
vertical position
Unscrew solonoid and clean the
orifice and/or replace diaphragm
Reduce the water supply pressure
Unscrew solonoid, remove
diaphragm and clean or replace.
Use scale remover if needed.
Clean or eliminate cause of
interference
Decrease the range or eliminate
case of reflection
Remove, clean and reinstall
Page 16
Request your 200 page
catalogue today on
01424 202224
DB 200
page 178
DBL 400
page 180
WP 106
page 11
WP 208R
page 12
WP 112R
page 105
BC 2006
page 159
Re
la
ted items
DOLPHIN
Tap s
Co
unter M
ounte
d
•
Touch
Free Tap –for u
lt
ima
te hyg
iene
–pre
ven
ts cross
conta
minatio
n
•
Quality
polished
chrome
plate
d bra
ss or lacque
red n
ickel
plated b
rass
finishes avai
lable
•
Wa
ter S
upp
ly: S
ingle inlet c
old or p
re-m
ixe
d –a TMV2
or
TMV3
thermos
tatic
m
ixing va
lve
is re
commended
fo
r
pre
mixed
applicatio
ns
. For 2 inle
t h
ot
and co
ld fee
d see
page
183
•
F
low rate
– 6
litres/m
inute
(d
own
to 1
.89 litre
s/m
inu
te –
please
specify
at tim
e of o
rdering)
•
Neopea
rl A
erator
•
Tap
settings can b
e adjusted m
anua
lly o
r by us
ing
remote
con
trol (DB51 –
see
page 188)
•
Manda
to
ry H
ygiene F
lush feature
can b
e spec
ified to
com
bat Leg
io
nella
–please
spec
ify at tim
e of o
rerin
g
•
W
RAS App
ro
ved P
roduct
•
2 year
manu
fa
cture
r’s
warranty
•
Max
imum
w
ater tempe
rature
70ºC
•
Opera
tin
g pressu
re 0.5–8.0
bar (7
–116
PSI)
Produc
t D
ata
•
H 142 x Ø
45 mm
•
Pro
jec
tion 105mm
•
Power
Connec
tio
ns
: ta
p m
ale, p
owe
r s
ourc
e fema
le
•
Counte
r h
ole Ø
28-34mm M
in-max
th
ickne
ss 2-27mm
•
3/8"
B
SP w
ate
r supp
ly connec
to
r
•
Powe
r: Plug-
in 9 v
olt trans
form
ers o
r 9 volt battery
(w
ith
low battery wa
rning) –for other
p
owe
r sou
rce options see
page 190-191
Product Co
des
Polis
hed
chrome
finis
h
•
Powe
re
d b
y 6 x A
AA
/ 9
v PP3 b
attery
DB
200C
•
Powere
d b
y 9v p
lug in tra
ns
form
er
DB
225C
Brushed
nicke
l finis
h
(des
igned
to m
atc
h b
rushed
stainle
ss s
tee
l)
•
Powe
re
d by 6
x AAA
/ 9
v PP3 ba
ttery
DB
200S
•
Powered
b
y 9v p
lug in tra
ns
forme
r
DB
225S
DB 200 / DB 225 Dolphin Blue Infrared Tap
178Dolphin D
ispen
sers
Technical help
line 0
1424 202224
135°
105
100
Ø
50
Ø45
142
Power
source
Toilet Tissue
Dispenser
Paper Towel
Dispenser
Combination
Units
Hot Air H
and
Dryers
Taps
Bins
Washroom
Accessories
Grab Rails
Baby
Changing
Hotel R
ange
Consum
able
s
Product
Fam
ilies
Installation
Guide
Soap
Dispen
sers
Bellchem WD9 174-269 t
aps, bins, access.qxd:Layout
1
Dolphin Solutions Ltd
Southpoint, Compass Park, Bodiam, Robertsbridge, TN32 5BS
Tel: +44 (0)1424 20 22 24
Fax: +44 (0)1424 205 200
info@dolphinsolutions.co.uk
www.dolphinsolutions.co.uk
Loading...