Dolphin BC22011SS User Manual

BC22011SS

DOLPHIN HOT AIR
HAND DRYER

User Manual

Please read carefully before use

2 BC2201SS User Manual www.dolphinsolutions.co.uk

Operating Voltage

Warm Air Volume Output

Warm Air Temp Output

Motor Type

Motor Thermal Protection

Heater Element

Heater Thermal Protection

Drying Time

Circuit Operation

Sensor Range

Time Protection

Time Duration

Cover Type

Cover Finish

Net Weight

Shipping Weight

Unit Size

230-240Vac,50/60Hz,2.0-2.4kW

314.5m³/h (185 CFM)

60°C at ambient T=20°C

¼ HP, 7500 rpm, Brush Type, 200W, Dual Ball Bearings

Auto Resetting Thermostat turns unit off at 105°C (221°F)

2200W

Auto Resetting Thermostat turns unit off at 87°C (189°F)

Thermal fuse cuts unit off at 141°C (286°F)

Less than 15 seconds

Infrared Automatic, self adjusting

Adjustable;standard 18 cm± 2 cm

1 minutes auto shut off

2 seconds delayed turn off after last sensor read

Stainless steel, 1.5 mm thick

Stain finished

4.5kg [9.9lbs]

5.5kg [12.1lbs]

W x H x D [254mm x 326mm x 120mm]

Operating Instructions and Parts Manual (Automatic)

Surface Mount

254 mm (10")

326 mm (12-7/8")

AUTOMATIC HAND DRYER

120 mm (4-3/4")

3 BC2201SS User Manual www.dolphinsolutions.co.uk

General safety information:

-- NOTE: Do not install dryer over washbasin --

Disconnect power at the

service breaker before installing or servicing.

NOT FOR HOUSEHOLD USE - MAY CAUSE BURNS.

" IMPROPRE A L'USAGE DOMESTIQUE - PUET OCCASIONNER."

This product is intended

for installation by a qualified service person.

Use 1.5 mm² solid conductor for wiring.

All units must be supplied

with a 3-wire service. The ground wire must

be connected to the dryer's backplate.

Failure to properly ground

unit could result in severe electrical shock

and/or death.

Installation

Type Y attachment

If the power supply cord is damaged, it must be replaced by the manufacturer

or its service agent or a similar qualified person in order to avoid a hazard.

Means for disconnection must be incorporated in the fixed wiring in

accordance with the wiring rules.

1. Make sure power supply breaker is switched off. Installation must be carried out in accordance

with the current edition of the local wiring regulations code having jurisdiction. Installation should

be performed only by a qualified electrician.

2. Place template against wall at desired height (see mounting height recommendations) and mark

locations of 4 mounting holes and wire service entry at knockout (KO) location.

Note: For two or more dryers, dryers should be no closer than 24 inches (610 mm) on center.

3. Remove and retain 2 cover screws and cover.

4. Connect supply wires to terminal block where indicated and connect ground wire to base plate

with ground screw

A. Connect the live wire (colored red or black or brown ) to the terminal block marked "L".

B. Connect the neutral wire (colored white or blue) to the terminal block marked "N".

C. Connect the ground wire (colored green or green and yellow) to the green screw marked " ").

Note that colors of live and neutral wires depend on voltage of supply service.

5. Replace cover. Do not over-tighten screws.

Connections:

4 BC2201SS User Manual www.dolphinsolutions.co.uk

Operation

No-touch operation

Shake excess water from hands.

Place hands under the outlet to start operation.

Rub hands lightly and rapidly.

Stops automatically after hands are removed.

Periodic cleaning of the unit is recommended to ensure optimum performance.

Cleaning and Maintenance

Disconnect the electrical supply.

Remove the two cover-mounting screws.

Remove the cover.

Clean all dust lint from the interior of the dryer.

Wipe the cover with a damp cloth and mild

cleaning solution. Do not Soak. Never use

abrasives to clean the cover.

Replace the cover. Do not over tighten the screws.

Recommended mounting heights

- from bottom edge of dryer above finished floor (AFF)

Men

Women

Children 4-7 years

Children 8-10 years

Children 11-13 years

Children 14-16 years

Handicaped

(40")

(38")

(32")

(34")

(36")

(38")

(34")

1000 mm

960 mm

812 mm

860 mm

910 mm

960 mm

860 mm

‘Unit should be mounted to give no less than 300mm clearance from the bottom of the unit

to the nearest surface below’

LIMITED THREE-YEAR WARRANTY

Please see our website by following this link: http://www.dolphindispensers.co.uk/

o

r contact our customer service team on 01424 202224 for more details.

Warranty

LIMTED FIVE YEAR WARRANTY

5 BC2201SS User Manual www.dolphinsolutions.co.uk

Sensing Range Adjustment

The exact sensing range was pre-set by maker.

You’d better not change it.

If you want to modify the Sensing Range, please proceed the following procedures.

(And please also refer to TIMER ASSEMBLY DRAWING (-) as follows)

First of all, cut off the power supply, please.

Remove the ENCLOSURE / HOUSING of hand dryer.

Remove the outer case of TIMER ASSEMBLY.

Find the SENSING RANGE ADJUSTER inside the TIMER ASSEMBLY and

use tiny screw driver - type or + type to turn round the SENSING RANG ADJUSTER:

(A) Clock--------------

Lengthen the sensing range (+)

(B) Counterclockwise-----

Shorten the sensing range (-)

" "" "

Lengthen the sensing range (+)

Shorten the sensing range (-)

Diagram

1

2

3

4

5

6

7

8

9

10

11

12

13

14

17

15

16

6 BC2201SS User Manual www.dolphinsolutions.co.uk

7 BC2201SS User Manual www.dolphinsolutions.co.uk

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

Satin Finished - Stainless Steel #4

Security Hex Screw

Security Hex Wrench

Brush Motor

Blower

Thermostat

Blower Housing A

Heater Element

Blower Housing B

Motor Bracket Assembly

Sensor Module + Circuit Board Module

Grounding Screw

Grounding Washer

Terminal Block

Base Plate

Cable Clamp

Nylon Bushing

Reference

Number

Qty.Description

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

Dolphin Solutions

Southpoint, Compass Park, Bodiam, Rober tsbridge TN32 5BS

Tel: [phone]

Fax: [phone]

www: dolphinsolutions.co.uk

[e-mail]