Page 1
BC2001 / BC2001B
DOLPHIN VELOCITY HIGH SPEED
HAND DRYER
User Manual
Please read carefully before use
Page 2
ITEM CATEGORY
Operating Voltage
Warm Air Speed Output
Motor Type
Motor Thermal Protection
Heater Element
Heater Thermal Protection
Drying Time
Circuit Operation
Sensor Range
Timing Protection
Drip proof
Isolation
Net Weight
Shipping Weight
Unit Size
PERFORMANCE DATA
TECHNICAL SPECIFICATIONS
220-240Vac, 50/60Hz, 1.34-1.6kW
75-100m/s, adjustable
350-700W, 12000-18000r.p.m., Adjustable; Brush Type, Dual Ball Bearings
Auto Resetting Thermostat turns unit off at 95°C {203°F}
450-900W, adjustable
Auto Resetting Thermostat turns unit off at 85°C {185°F}
Less than 15 seconds
Infrared Automatic, self adjusting
Standard [170 ± 20mm], Adjustable, The range is [120 - 220mm]
60 seconds auto shut off
IP21
CLASS 1
5.8kg
6.6kg
201mm (W) x 286.5mm(H) x 175mm (D) (BC2001 ,BC2001B)
205mm (W) x 294mm (H) x 180mm (D) (BC2001W)
BC2001- Stainless steel; #4 satin finished. (AISI 304 t:1.2 mm)
COVER TYPE/ COVER FINISH
Hand drier
High-Speed
BC2001
BC2001B
BC2001W
BC2001B- Stainless steel; Bright finished. (AISI 304 t:1.2 mm)
Stand-by Power
Less than 0.5W
BC2001W- Steel; White porcelain enameled coating. (t:1.6 mm)
286.5 mm
201 mm175 mm
294 mm
180 mm
205 mm
(BC2001 ,BC2001B)
(BC2001W)
Operating Instructions and Parts Manual (Automatic)
Surface Mount
BC2001 User Manual www.dolphinsolutions.co.uk
Page 3
Operating Instructions and Parts Manual
Hand drier
Surface-mounted high speed hand drier
General safety information
Disconnect power at the service breaker before
installing or servicing. Not for household use
may cause burns.
This product is intended for installation by a
qualified service person.
Use 1.2mm² solid conductor for wiring.
All units must be supplied with a 3-wire service.
The ground wire must be connected to the
dryer's backplate.
Failure to properly ground unit could result in
severe electrical shock and/or death.
WARNINGWARNING
DANGERWARNING
Circuit Diagram
Circuit Board Module
Transistor
Power Switch
MO2HE2NMO1HE1L
Transistor
Power Switch
G
N
L
G/Y
Blue
Brown
Motor With Thermal Switch 2A
Heater With Thermo-fuse
1234
SW.
FOR HEATER
ON
1
Black
Black
VR
G
G/Y
FOR SENSOR
Y2 Filter
(ONLY 208~240V)
(ONLY 208~240V)
LED
Red(110-120V)/Brown (208-240~277V)
White(110-120V)/Blue (208-240~277V)
Thermostat
【Type Y attachment】
If the power supply cord is damaged, it must be replaced by the manufacturer
or its service agent or a qualified person in order to avoid a hazard. Disconnect
the fixed wiring only in accordance with the wiring rules.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
NOTE: We do not recommend installing this dryer above a basin. If you are installing
this dryer above a basin, please make sure that reflection won’t occur.
BC2001 User Manual www.dolphinsolutions.co.uk
Page 4
Installstion
1. Make sure power supply breaker is switched off. Installation must be carried out in accordance
with the current edition of the local wiring regulations code having jurisdiction. Installation should
be performed only by a qualified electrician.
2. Place template against wall at desired height (see mounting height recommendations) and mark
locations of 4 mounting holes and wire service entry at knockout (KO) location.
Note: For two or more dryers, dryers should be no closer than 24 inches (610mm) on center.
3. Remove and retain 2 cover screws and cover.
4. Connect supply wires to terminal block where indicated and connect ground wire to base plate
with ground screw.
A. Connect the live wire (colored red or black or brown ) to the terminal block marked "L".
B. Connect the neutral wire (colored white or blue) to the terminal block marked "N".
C. Connect the ground wire (colored green or green and yellow) to the terminal block marked " ".
Note that colors of live and neutral wires depend on voltage of supply service.
5. Replace cover. Do not over-tighten screws.
Connections:
Recommended mounting heights
Men
Women
Children 4-7 years
Children 8-10 years
Children 11-13 years
Children 14-16 years
Handicaped
960mm
812mm
860mm
910mm
960mm
860mm
1000mm
‘Unit should be mounted to give no less than 300mm
clearance from the bottom of the unit to the nearest surface below’
- from bottom edge of dryer above finished floor (AF
F
Periodic cleaning of the unit is recommended to ensure optimum performance.
Cleaning and Maintenance
Disconnect the electrical supply.
Remove the two cover-mounting screws.
Remove the cover.
Clean all dust lint from the interior of the dryer.
Replace the cover. Do not over tighten the screws.
Wipe the cover with a damp cloth and mild
cleaning solution. Do not Soak. Never use
abrasives to clean the cover.
Operation
No-touch operation.
Shake excess water from hands.
Place hands under the outlet to start operation.
Rub hands lightly and rapidly.
Stops automatically after hands are removed.
Operating Instructions and Parts Manual
Hand drier
Surface-mounted high speed hand drier
BC2001 User Manual www.dolphinsolutions.co.uk
Page 5
Use wire cutter to remove filter assembly.Fix new filter assembly to the cover.
Change filter assembly
Settıng Adjustmenet
A. Warm air speed adjustment
B. Heater Element Switch ON/OFF
1.Switch off the power, loosen the cover screws and remove the cover.
2.Adjust the heater switch on the PCB with a small
plastic or wood flat blade probe.
2-1. Heater ON: Slide the switch to "ON".
2-2. Heater OFF:Slide the switch to "1".
Use screwdriver to adjust air speed.
Install the cover once adjustment is completed.
Clockwise: Increases the air speed(+) .
Counterclockwise: Decreases the air speed(-) .
Operation
C. Sensor range adjustment
1.The recommended unit sensor range is 150mm.
This can be adjusted from 120mm to 220mm.
2.Clockwise: Increases the sensing range(+) .
3.Counterclockwise: Decreases the sensing range(-) .
4.DO NOT OVERTURN!
SW.FOR HEATER
VR.FOR SENSOR
IItt iiss rreeccoommmmeended to change the filter every six months.
Operating Instructions and Parts Manual
Hand drier
Surface-mounted high speed hand drier
Turn off power to the dryer at electrical panel.
Remove cover.
BC2001 User Manual www.dolphinsolutions.co.uk
Page 6
BC2001 User Manual www.dolphinsolutions.co.uk
. Pull off the six wires and remove the fixing screws of the timer.
. Ensure that the two flanges on the timer to be wedged in the two holes are on the base plate.
. Fix the timer to the blower and connect the four wires to the timer as the photos of procedure 1.
Page 7
Sensor replacement
1. Pull off the wires that connect timer and remove the fixing screws of the timer.
2. Fix the sensor on the sensor bracket as in the photos of procedure 1, and plug the wires on the tim
3. Remove the screws from the sensor bracket to take out the sensor.
O
perating Instructions and Parts Manual
Hand drier
Surface-mounted high speed hand drier
BC2001 User Manual www.dolphinsolutions.co.uk
Page 8
. Remove the black screws on the senor. Install the new sensor and reverse Steps 1~3 to
fasten the sensor.
BC2001 User Manual www.dolphinsolutions.co.uk
Page 9
BC2001 User Manual www.dolphinsolutions.co.uk
Motor replacement
1. Remove the wires that connect motor to the timer.
2. Loosen the fixing screws of the blower.
Operating Instructions and Parts Manual
Hand drier
Surface-mounted high speed hand drier
Page 10
BC2001 User Manual www.dolphinsolutions.co.uk
3. Remove the screw on base plate and fan blower, and then remove the bracket of fan blower.
4. Remove upper fan blower, motor rubber (big) and motor in order, and then replace the motor
with a new one.
Operating Instructions and Parts Manual
Hand drier
Surface-mounted high speed hand drier
Page 11
BC2001 User Manual www.dolphinsolutions.co.uk
5. To replace the Motor, the wire set must be fixed to the ditch in the lower housing of the blower.
Reverse Steps 1~4 to fasten the motor.
Operating Instructions and Parts Manual
Hand drier
Surface-mounted high speed hand drier
Page 12
BC2001 User Manual www.dolphinsolutions.co.uk
Heater replacement
1. Remove the wires that connect heater to the timer.
2. Loosen the fixing screws of the blower .
Operating Instructions and Parts Manual
H
and drier
Surface-mounted high speed hand drier
Page 13
BC2001 User Manual www.dolphinsolutions.co.uk
Heater replacement
4. Remove the screws on base plate and fan blower bracket. Remove the fan blower bracket
to separate the motor assembly and the base plate.
3. Loosen the fixing screws of the blower .
Operating Instructions and Parts Manual
Hand drier
Surface-mounted high speed hand drier
Page 14
BC2001 User Manual www.dolphinsolutions.co.uk
6. Replace the heating element with a new one.
7. To replace the Heater, the wire set must be fixed to the ditch in the lower housing of the blower.
Reverse Steps 1~6 to fasten the heater.
5. Remove the screws on air outlet.
Operating Instructions and Parts Manual
Hand drier
Surface-mounted high speed hand drier
Page 15
BC2001 User Manual www.dolphinsolutions.co.uk
Brushes replacement
THIS UNIT MUST BE FITTED AND SERVICED BY SUITABLY QUALIFIED PERSONNEL
Take off the motor.
Disconnect wires from the brush.
Using the screwdriver to take off the fixed
screws from the brush motor for the two sides.
Replace with new brush and fasten the fixed
screw, then connect the wire on the motor.
5
Important Information
This Product falls within the scope of the Waste Electrical &
Electronic Equipment Directive 2002/96 EC. (WEEE)
NOTE:
This Product should not be disposed
of with household waste
Please recycle where facilities exist.
Operating Instructions and Parts Manual
Hand drier
Surface-mounted high speed hand drier
Turn off power to the dryer at electrical panel.
Remove cover.
Using the screwdriver to take off the bracket
from the base plate.
Using the screwdriver to take off the blower
housing top from the blower housing bottom.
Page 16
BC2001 User Manual www.dolphinsolutions.co.uk
LIMITED THREE-YEAR WARRANTY
Warranty
Please see our website by following this link: http://www.dolphindispensers.co.uk/
or contact our customer service team on 01424 202224 for more details.
Diagnostics and Remedies
If the dryer will not run
Symptom Corrective Actions for Initial Installation Failures
Symptom Corrective Actions for In-Service Failures
First ensure that the breaker supplying the dryer is operational. If it is,
disconnect the power and remove the dryer cover. Taking suitable
precautions to avoid shock hazard, reconnect the power and check for
Voltage at the terminal block. Verify that connections are made correctly.
Adjust the VR to make sure it is not set too low.
Ensure that there is no obstruction on or in front of the IR sensor. Clean
any dirt or debris off the sensor lens. If problem persists, replace sensor.
Ensure that the supply Voltage is correct. Dryer will run weakly if the
input Voltage is too low. Verify Voltage requirement on unit rating label
and correct supply as required.
Ensure that the supply Voltage is correct. Dryer will make a loud humming
noise if the input Voltage is too high. Verify Voltage requirement on unit
rating label and correct supply as required. If CBM has been damaged,
replace CBM, IR sensor module and VR component and cable.
First ensure that the breaker supplying the dryer is operational. If it is,
disconnect the power and remove the dryer cover. Replace the CBM
and IR sensor module. Test the VR for open circuit (see Technical
Specifications for value).
Replace VR if Ω = . Taking suitable precautions
to avoid shock hazard, reconnect the power and check for Voltage at
the terminal block.
∞
Ensure that there is no obstruction on or in front of the IR sensor.
Clean any dirt or debris off the sensor lens. If problem persists,
replace sensor.
Disconnect the power. Remove the dryer cover and disassemble the
blower-motor/fan housing. Test the thermostat for open circuit. Check
the heater element for signs of burning or breskage. Damaged element
must be replaced.
"
Check the output nozzle for obstructions. If none are present, disconnect
the power. Remove the dryer cover. Remove any dust/lint buildup from
intake vent slots. Disassemble the blower-motor/fan housing. Check the
motor brushes for worn condition (≤ 25/64 [10 mm] graphite remains)
and replace them, if necessary.
The dryer cycles by itself
or runs constantly
The dryer runs but air
stream is low pressure
and/or low velocity
The dryer makes a loud
noise and does not run
for a complete cycle
If the dryer will not run
The IR sensor only
"sees"
close range objects
The dryer only blows cold
air during a full cycle
The air stream is low
pressure and velocity
The heater gets hot but
no air stream is produced
Disconnect the power. Remove the dryer cover and disassemble the blower-
motor/fan housing. Replace the fan motor.
Operating Instructions and Parts Manual
Hand drier
Surface-mounted high speed hand drier
Page 17
BC2001 User Manual www.dolphinsolutions.co.uk
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Diagram
Operating Instructions and Parts Manual
Hand drier
Surface-mounted high speed hand drier
Page 18
BC2001 User Manual
Dolphin Solutions
Southpoint, Compass Park, Bodiam, Robertsbridge TN32 5BS
Tel: 01424 202224
Fax: 01424 205200
www: dolphinsolutions.co.uk
info@dolphinsolutionss.co.uk
Repair parts list
1
2
3
4
5
6
7
8
9
10
11
Key
Security hex screw (2 reqd.)
Stainless Steel - Bright finish (BC2001B)
Stainless Steel - Satin finish (BC2001)
(BC2001W)
Shock absorber
Blower housing - Top
Motor rubber - Large
Motor
Motor rubber - Small
Blower housing - Bottom
Heater element
Air outlet
Sensor bracket
Steel - White porcelain enameled coating
Description
Repair parts list
Sensor module
Blower housing bracket
Base plate
Nylon hole bushing
Cable clamp
Terminal block
Grounding screw
VR (variable resistance)
VR bracket
Circuit Board Module
Security hex wrench
Filter assembly
LED assembly (only for BC2001W)
12
13
14
15
16
17
18
19
20
21
22
23
24
Operating Instructions and Parts Manual
Hand drier
Surface-mounted high speed hand drier
Loading...