Dolphin BC101-PR, BC101-PRD Installation Instructions And Owner's Manuals

BC101ES

DOLPHIN TITAN CHANGING UNIT

› Carrying capacity of more than 400kg

› An alternative design embodying strength, safety and hygiene in a robust

construction

› Ideal for use in public toilets, washrooms or any area particularly vulnerable

to vandalism

› Safety strap operable with one hand

› Aluminium Unit with rounded edges and stainless steel cappings

› Optional liner roll dispenser above the table

› Pneumatic shock absorbers concealed in strong stainless steel mount

casings

› Pneumatic shock absorbers, facilitating smooth and noiseless operation

› Offers your customers a unique service and optimum safety

› Hygienic and a customer-friendly solution

HEIGHT 967 MM

WIDTH 788 MM

PROJECTION CLOSED 105 MM

PROJECTION OPEN 626 MM

PRODUCT CODES

› Linen roll dispenser

BC101-PRD

› Paper rolls BC101-PR

TECHNICAL HELPLINE 01424 202224
DOLPHINSOLUTIONS.CO.UK

269

100

967

798

626

Plan

Elevation

Section

BC 101-ES Dolphin Prestige Titan Changing

Unit and Liner Roll Dispenser

User Manual

Please read carefully before use

DOLPHIN

BC 101-ES User Manual www.dolphindispensers.co.uk

INSTALLATION INSTRUCTIONS

SAFETY BABY CHANGING TABLE

Read the Installation Instructions Thoroughly Before Commencing Installation

The design of the safety baby changing table makes it easy to mount in even very small

rooms. The changing table must be mounted onto a wall which is suited to carry the weight

of the table as well as a baby – preferably a solid wall!

Where To Mount the Baby Changing Table

Determine the ideal place to mount the baby changing table. Keep in mind that the depth of

the changing table is 625 mm in open position. The distance from the floor to the lower edge

of the table mountings should be approx. 750 mm (see FIG. 1). Doorways, sinks etc. should

of course also be taken into consideration when choosing where to mount the changing table.

IMPORTANT: Do NOT mount the table in a chlorine-containing environment!

Marking and Drilling Holes

To mount the changing table onto brick, gas concrete or the like, use 10 mm screws and

matching universal plastic dowels – e.g. Fischer fixings type S-12.

When mounting the changing table onto a cavity wall of min. 16 mm (or 2 x 13 mm) plaster

board, we recommend prior mounting of a reinforcement plate of stainless steel, plywood or

the like, onto which the changing table is subsequently mounted. Attach reinforcement plate

to the wall using a considerable number of special metal cavity fixings, Fischer part. no. BC

62328 or equivalent (part. no. BC 62315 for double plate). The changing table itself is also

mounted with these screws and dowels – plus one metal washer per screw hole. For further

details, please refer to the instructions of the dowel supplier.

In places where plaster walls have not yet been finished, we suggest mounting a 16 mm

plywood board on the inside of the plaster wall, rendering the need for a reinforcement plate

on the outside unnecessary.

Mark and drill holes as indicated on FIG. 1. The top holes for the table mountings should be

drilled into solid brick - not into a joint.

IMPORTANT: Be sure to drill the holes for the mountings exactly vertically underneath each

other, or the pneumatic shock absorbers inside the mountings may break!

MOUNTING THE BABY CHANGING TABLE

ݢ Disassemble the cover plates of the table mountings by removing the 6

screws (3 on each) with a Torx screwdriver no. 20.

ݣ Mount the table onto the wall, making sure that it is completely level.

ݤ The changing table is factory pre-adjusted to easily close when given a

slight push from open position.

ݥ Check that the changing table is mounted solidly onto the wall.

ݦ Check that the shock absorbers can pass freely when opening and closing

the table.

ݧ Reassemble the cover plates onto the mountings.

FIG. 1

PAPER ROLL HOLDER

CHANGING TABLE

The dimensions stated are based

on a work height of approx. 950 mm.

BC 101-ES User Manual www.dolphindispensers.co.uk

BC 101-ES User Manual www.dolphindispensers.co.uk

MOUNTING PAPER HOLDER

The paper holder consists of the following parts:

1 holder
Left-side mountings with lock
Right-side mountings
2 keys

ݢ Mark and drill holes as indicated on FIG. 1.

ݣ Fix the mountings onto the wall with 6 mm screws and plugs suited for the

wall type onto which the paper holder is to be mounted.

ݤ Place a paper roll loosely in the paper holder and tip the holder towards the

wall, making the white locking devices click.

Components

BC 101-ES User Manual www.dolphindispensers.co.uk

Components

BC 101-ES User Manual www.dolphindispensers.co.uk

Spare Parts

Position No. Part No Description

1 BC 65524 Hood for mounting bracket, complete, left

2 BC 65525 Hood for mounting bracket, complete, right

3 BC 65541 Crank

4 BC 65546 Mounting bracket, complete, left

5 BC 65547 Mounting bracket, complete, right

6 BC 65534 Spacer Ø25 mm, for spindle

7 BC 65531 End flange, left

8 BC 65532 End flange, right

9 BC 20040 Nut M5, stainless, self-locking

10 BC 65516 Aluminium table-top, 790 mm, white

11 BC 20038 Nut M6, stainless

12 BC 20047 Tight-fitting bolt M5 6x60 mm

13 BC 20041 Allen bolt, stainless, M6 x 25 mm

14 BC 20057 Locking ring Ø40 DIN 472

15 BC 65562 Spherical bearing

16 BC 20042 Allen bolt for crank (setscrew), stainless, M6 x 16 mm

17 BC 65402 Gas spring, 330 N, (Bansbach)

BC 65407 Gas spring, 350 N, (Scandiloc)

BC 65406 Gas spring replacement set with crank, screws etc.

18 BC 20065 Spacer, polyamide, Ø5.2 x Ø10 x 3

(only for installation with part. no.: 65402)

BC 20855 Spacer, nylon, Ø5.3 x Ø10 x 1

(only for installation with part. no.: 65407)

19 BC 20044 Screw, countersunk, stainless, M4 x 10, torx

20 BC 20053 Screw, stainless, M6 x 20 mm, torx

21 BC 20835 Spacer, flat, stainless, A2, M5 x 10

22+23+24 BC 65551 Safety belt complete with buckle

25 BC 40068 Screw, stainless, M4 x 12 mm, torx

BC 65520 Measuring band

BC 65630 Pictogram, door

DOLPHIN

Bell-Chem Products Company

Haywood Way, Hastings, TN35 4PL

Tel: [phone]

Fax: [phone]

www: dolphindispensers.co.uk

[e-mail]

BABY CHANGE

INSTALLATION INSTRUCTIONS

NAPPY CHANGING UNIT INSTALLATION

Stainless Steel Units

STEEL UNITS

Each stainless steel unit can either
be surface-mounted or recessed.
A matching stainless steel cover
frame is available for surface­mounted installations.

RECOMMENDED MOUNTING HEIGHT TO BASE OF UNIT:

Standard – 900mm

Wheelchair – 750mm

• In all mountings, the flat fender washer must be inserted

underneath the finishing washer: installing the unit using only
the finishing washer may result in the washer biting directly
into the body of the unit with consequent damage and loss
of stability.

• Nappy changing units are no stronger than the anchors or

substrates to which they are attached and as such must be
firmly secured in order to support the loads for which they
are intended.

RECESSED FIXING IN
MASONRY

Each unit has six recess mounting holes.
Form the opening in the brick or
blockwork wall, incorporating an
appropriate lintel to span the opening.
Install rough timber fixing grounds and
screw fix the changing unit to the
reveals of the opening using minimum
5mm screws.
Before final tightening, insert packing
shims as necessary for alignment and to
obviate any distortion on tightening.
Use either flat head screws with
finishing washers and flat washers or
pan head wood screws with flat
washers, making sure that consideration
is given to the operating clearance and
that the back flange of the unit neatly
masks the opening and the termination
of the wall finish.

RECESSED FIXING IN
STUDWORK

Timber double stud blocking is
necessary around the opening.
After locating the unit within the
framed opening, insert packing shims as
necessary for alignment and snug fitting.
Secure the unit to the blocking using
minimum 5mm flat head wood screws
with finishing washers and flat washers
or pan head wood screws with flat
washers, making sure, as with all fixing
methods, that consideration is given to
the operating clearance.

SURFACE MOUNTING

The unit can be fixed directly through
the back plate using screws and
appropriate wall plugs and plastic caps
to cover the screw heads.
A matching stainless steel cover frame
is available for surface-mounted
installations which engages the changing
unit with a snap fit. The cover frame
covers the otherwise exposed edges
and provides a neat finishing surround.

POLYETHYLENE UNITS

Each unit has four mounting ports based on a traditional
400mm stud spacing.
Two additional por ts are provided for optional use.
All fixings are supplied with each unit to cater for fixing to
either solid masonry or studded wall constructions.

FIXING TO MASONRY

Secure the unit to brick and concrete block substrates
using four 5mm x min.75 mm wood screws into
proprietary wall plugs.
The flat fender washer is to be inserted underneath the
finishing washer. Finally, insert the snap-fit plastic covers in
each fixing port to cover the fixings.

ALTERNATIVE FIXING METHOD TO STUDWORK

The BC 100-EH/BC 100-EV unit can be fitted with the EZ Mount backer plate
to provide an alternative method of fixing to studded walls.
Two galvanised steel mounting bars are supplied, one pre-fixed to the rear of
the unit and the other loose for fixing to the wall. The wall bar has a multitude
of fixing holes to cater for variable stud positions.

1

Mark out and drill
fixing holes. Insert

toggle.

2

Twist toggle freely to

gain purchase on the
supporting member.
There should be a
minimum cavity clearance
of 65mm to allow the
toggle bar to turn.

3

Push the integral disc

along the toggle to
make a snug purchase on
the wall face. The toggle
strands are rachetted to
hold the disc in place.

4

Cut off the surplus

projection of the
toggle and offer up the
unit for fixing.

5

Align and engage the

fixing bolt in the
threaded toggle bar with
washers engaged. The flat
fender washer is to be
inserted underneath the
finishing washer. Finally,
insert the snap-fit plastic
covers in each fixing port.

RECOMMENDED MOUNTING
HEIGHTS:

Standard – 900mm
Wheelchair – 750mm

NAPPY CHANGING UNIT INSTALLATION

Polyethylene Units

Cover cap

Toggle

Fixing to studwork

Dolphin Solutions Ltd
Southpoint, Compass Park,
Junction Road
Bodiam, TN32 5BS,
United Kingdom
T [phone]
[e-mail]
dolphinsolutions.co.uk

© Dolphin Solutions Ltd

SOUTHPOINT, COMPASS PARK,

BODIAM, ROBERTSBRIDGE,

TN32 5BST, UNITED KINGDOM

+ 44 (0)1424 202 224 TEL
+ 44 (0)1424 205 200 FAX

[e-mail]

dolphinsolutions.co.uk