MANUAL FL190
®
Fiber-Lite
HIGH INTENSITY FIBER OPTIC ILLUMINATORS
INSTRUCTION
MANUAL
for Models 190
Illuminators
Your purchase of the DolanJenner Fiber-Optic Illumination
System will provide you with
many years of service in a large
variety of applications which
require high intensity, yet cool
illumination. Please read the
following instructions to ensure
that maximum performance is
obtained from your system.
INTRODUCTION
The 190-1 Fiber Optic Illuminator gives high-intensity "cold" light
where you need it most. The fiber optics absorb heat and transmit
high-intensity light, and the gooseneck light pipe lets you position the
lens from a variety of oblique angles.
It is ideal for illumination in temperature-sensitive applications such
as specimen preparation, dissection, culture work or
micromanipulation. The illuminator can also be used in conjunction
with a stereomicroscope lamp port for incident or transmitted
illumination with or without the lens.
FEATURES
A powerful 0.19 inch (4.8mm) diameter fiber optic that provides
over 4,000 foot candles at a 6 inch distance in a 0.87 inch (22mm)
diameter spot of high intensity "cold" light.
A 30 watt quartz-halogen vibrationless source (convection-cooled) at
a color temperature of 3100 degrees K, suitable for tungsten film.
Gooseneck flexibility is excellent for multipositioning. The fiber
optic light pipe always remains at the ambient temperature and is
safely handled at all times to enable optimum positioning for reduced
glare. This eliminates the possibility of burnt fingers on adjustment
and, at the same time, increases eye comfort.
Convenient 28mm focal length, slide-lock lens which is quickly
focused to provide light spot diameters from 0.16inches to 2.87 inches
(4mm to 73mm).
The four position light intensity switch offers easy light-intensity
selections.
CHANGING THE ILLUMINATOR LAMP
The following procedure outlines the steps necessary to replace the
lamp.*:
1. Unplug the illuminator from the wall socket before disassembling
the unit.
2. If the light pipe must be removed to take off the cover, unscrew it by
straightening it as much as possible and turning it counterclockwise
while grasping it at the base. This step is only necessary if the light
pipe is permanently mounted.
3. Remove the 4 button-head screws using a 5/64" Hex Allen wrench.
Lift off the cover assembly slowly until the lamp is exposed.
4. Unplug the lamp from its socket.
5. After the lamp is disconnected unsnap it from the lamp retainers on
the bracket. (Figure 1).
6. Reverse this process to install a new lamp.
*Note: Use only EKZ replacement lamps.
Lamp Retainers
Bracket
LAMP
WIRING DIAGRAM
Yellow
Yellow
TRANSFORMER
SWITCH
LINE
Black
Blue
White
Brown
White
Red
Black
White
Green
PERFORMANCE STATEMENT
Dolan-Jenner Industries, Inc. (DJI) recognizes that its illuminator
products may be used under an almost unlimited variety of conditions.
As such, we are prepared to assist the customer in the selection and
application of any of these products. This includes application
engineering, sample testing and other means as determined by DJI.
Where DJI has made specific recommendation for its products,
systems or detection techniques (based on complete and detailed
information furnished by the customer), we will extend every effort to
assure that the customer is satisfied with the performance of our
products. Continual development and improvement of DJI products
may require changes in details that do not coincide with descriptions
or illustrations shown. All fiber optic bundle diameters are nominal.
3YEAR WARRANTY ON LIGHT SOURCES
Dolan-Jenner Industries, Inc. (DJI) warrants its products to be free
from defective material and workmanship. Any light source or parts
thereof which are determined by DJI to be defective within three years
(average product life cycle) from date of shipment will be replaced or
repaired at our option. This policy is effective AUGUST 1, 2005 and is not
retroactive. All fiber optics are warranted for one year. This warranty
specifically excludes both incandescent and quartz-halogen lamps and
optical filters. Any products which, in our opinion, have been
subjected to misuse, neglect, incorrect wiring, or where installation
procedures are not in accordance with the instruction manual, are
excluded from the warranty. Nor does this warranty extend to products
on which repair or alterations have been made outside the factory, or
on which the identification or serial number has been altered, or to
accessories not of our manufacture. Our obligation with respect to
products or parts covered by this warranty shall be limited to repair or
replacement, F.O.B., Boxborough Massachusetts. In no event shall DJI
be held liable for consequential or special damages, or for
transportation, installation, adjustment, or other expenses which may
arise in connection with such products or parts. This warranty is in lieu
of all other statements or warranties or guarantees, written or implied,
by DJI or its authorized representatives.
REPLACEMENT PARTS- MODEL FL 1900
PART NO. DESCRIPTION
02-015007-0000 Transformer
02-015851-0000 Lamp EKZ, 30W, 10.8V
02-015907-0000 Lamp Holder QEX-10
02-015908-0002 Lamp Holder, QCX-5
02-018202-0001 Switch
Components for 220V, 50/60Hz
02-015004-0001 Transformer
© 1995 Dolan-Jenner Industries, Inc. All Right Reserved Printed in U.S.A. Rev. B 05-000008-0000
Dolan-Jenner Industries, Inc. • 159 Swanson Road. • Boxborough, MA 01719
(978) 263-1400 • FAX: (978) 264-0292 • Toll Free: 1-800-83-FIBER
Loading...