999284802 08/2018
en-GB
-
The Formwork Experts.
Staxo 40 shifting wheel
Art. n°: 582218000 | 2010 models onward
Original Operating Instructions
Please retain for future reference
© by Doka GmbH, A-3300 Amstetten
© by Doka GmbH, A-3300 Amstetten
Original Operating Instructions Staxo 40 shifting wheel
Basic drawings of product
b
a
d
c
a ... min. 1158 mm - max. 1478 mm (adjusting range: max. 320 mm)
b ... 574 mm / 837 mm
c ... 456 mm
d ... 160 mm
e ... 110 mm
e
Intended use
The Staxo 40 shifting wheel is classified as a lifting
appliance. It may be used for horizontal reposition-ing
of Doka load-bearing towers Staxo 40, either with or
without formwork (intended use).
NOTICE
▪ Other use or use not in conformity with that
stated above is non-intended use and
requires the prior written approval of the
Doka company!
▪ It is forbidden to lift other manufacturers'
load-bearing towers with it.
With it, the following functions can be carried out:
▪ Lifting
▪ Wheeling
▪ Lining-and-levelling
▪ Lowering
Data on rating plate
Designation: Staxo 40 shifting wheel
Art.n°: 582218000
Dead weight: 21,7 kg
Max. load: 500 kg
Year of manufacture: see rating plate
h
b
b
98024-322-03
Permissible total weight of each unit for repositioning:
1000 kg (max. 4 Staxo 40 shifting wheels per unit)
NOTICE
When repositioning load-bearing towers that
include standard superstructures, remember:
Ratio b:h = max. 1:3, with 'b' being the narrowest side.
Custom constructions must be statically verified!
2 999284802 - 08/2018
Original Operating Instructions Staxo 40 shifting wheel
Maintenance & inspection
▪ Repairs may only be carried out by the manufac-
turer!
▪ Doka accepts no liability for products that have been
altered!
Before every use
➤ Check for any signs of damage or visible deforma-
tion.
Lifting accessories that do not meet the following criteria must be withdrawn from use
immediately:
▪ No deformation.
▪ No cracks or notches.
▪ No damage due to the influence of heat.
▪ Rating plate must be in place and clearly
legible
At regular intervals
Inspection of lifting accessories must be performed
▪
at regular intervals by an expert in conformity with
national statutory provisions.
Unless otherwise stipulated, such inspection must
be carried out at least once a year.
Storage
▪ Store lifting accessories in a dry and well ventilated
place, protected from the weather and from all corrosive substances.
Preconditions for use:
NOTICE
▪ There must be a flat, firm (e.g. concrete),
adequately dimensioned floor that is capable of supporting the load.
▪ Max. permitted inclination of trackway: 2%
The permissible inclination of the trackway
must be determined by statical calculation
(risk of overturning, rolling forces).
▪ Either bridge any openings in the floor with
sufficiently strong planking/boards secured
so that they cannot slip away to either side,
or close off openings with sufficiently strong
side railings!
▪ Keep the travel route clean and free of any
obstacles.
▪ It is only permitted to travel Doka load-bear-
ing towers that have been braced in accordance with the assembly plans and erection
rules given in the User Information booklet.
Fixing to the load-bearing tower
Preparations on the load-bearing tower
➤ In cases where the screw-jack feet are extended a
long way, reduce the extension length of the screwjack feet to dimension 'a'.
➤ Use the anti-dropout locks to fix the screw-jack feet
to the frames.
92848-200-02
a ... max. 40 cm
A Staxo 40 screw jack foot
B Staxo 40 anti-dropout lock
C Basic frame Staxo 40
C
B
a
A
3999284802 - 08/2018
Original Operating Instructions Staxo 40 shifting wheel
Preparations on the shifting-wheels
Adjust the shifting-wheels to the Staxo 40 frames
of the bottom "storey" of the tower:
➤ Fix the adjusting bracket in the required position
using a D16/125 bolt, and secure this with a linch pin.
F
E
D
92848-200-03
D Adjusting bracket
E D16/125 bolt
F Linch pin
Position of the adjusting bracket for:
▪ 0.90m frames
▪ upside-down 1.80m frames
▪ 1.20m frames
▪ 1.80m frames
Mounting the shifting-wheels to the loadbearing tower
➤ Bolt the shifting-wheel onto the Staxo 40 frame (in
the direction of the frames) with two D16/125 bolts,
and secure each of these with a linch pin.
G
E
F
E
G
F
92848-201-01
E D16/125 bolt
F Linch pin
G Fixing positions in the Staxo 40 frame
92848-200-01
92848-202-01
Wheeling
Raising the load-bearing tower
➤ Use the screwjack mechanism on the shifting-wheel
to raise the load-bearing tower max. 5 cm off the
ground.
92848-202-02
H
b
92848-203-02
b ... max. 5 cm
H Handle of the shifting-wheel screwjack mechanism
Quick lowering of the swivel castor:
1) Open the split nut of the shifting-wheel by
releasing its integrated quick-locking
device.
The screwjack mechanism plus swivel
caster are now lowered to the ground.
2) Close the split nut again and fix it with the
quick-locking device.
4 999284802 - 08/2018
Original Operating Instructions Staxo 40 shifting wheel
Wheeling the load-bearing tower
NOTICE
▪ Particular care is needed with:
- height offsets
- steps
- floor holes and wall openings
- strong wind
▪ It is forbidden for any third persons to linger
in the immediate danger zone!
▪ Exercise caution regarding the risk of over-
turning (particularly in strong wind).
▪ It is forbidden to use any mechanical assis-
tance during the wheeling operation!
▪ Take care to start moving gently, and to
exert a constant, uniform pull.
▪ Max. speed 4 km/h (walking pace)
▪ Special care is needed when travelling
across shoulders in the ground (no sharpedged shoulders, max. shoulder-height
15 mm).
▪ For longer breaks between operations, or
when the the load-bearing tower is permanently parked, take the load off the shiftingwheels (by lowering the tower to the
ground).
Crane-lifting of load-bearing towers with
shifting-wheels mounted to them
Follow the directions for resetting by crane
(slinging points etc.) in the "Staxo load-bearing
tower 40" User Information booklet.
➤ Check that the shifting-wheels are properly fixed to
the load-bearing tower.
Check to make sure that all the bolts are
secured by linch pins.
Lowering the load-bearing tower
NOTICE
The split nut must not be opened when loaded!
➤ First lower the load-bearing tower onto the ground by
turning the screwjack mechanism in the shiftingwheel.
Declaration of conformity
WARNING
➤ "Passenger transportation" is forbidden!
➤ Before the repositioning operation, remove
any loose items (e.g. fitting-boards) from the
load-bearing tower and formwork.
WARNING
Risk of overturning!
➤ The load-bearing tower may only be raised
by max. 5 cm in order to be travelled.
EC Declaration of Conformity
pursuant to EC Directive 2006/42/EC.
The manufacturer declares that by reason of its conception and
conforms – in the version marketed by ourselves – to the pertinent
fundamental health and safety stipulations of the relevant EC Directives.
The following harmonised Standards were applied:
design, the following product
Staxo 40 shifting wheel, Art. n° 582218000
▪ EN ISO 12100:2010
▪ EN 349:1993+A1:2008
Person authorised to compile technical documentation
(pursuant to European Directive on Machinery Annex II):
Dipl.-Ing. Ludwig Pekarek
Josef Umdasch Platz 1
A-3300 Amstetten
Amstetten, 07/08/2018
Dipl.-Ing. Ludwig Pekarek
Executive Manager
Authorised Officer, Head of Engi-
Doka GmbH
Josef Umdasch Platz 1
A-3300 Amstetten
Dipl.-Ing. Peter Reisinger
neering
92848-203-01
b ... max. 5 cm
b
5999284802 - 08/2018
Loading...