Dogtra E FENCE3500 User Manual

E-Fence 3500

By Dogtra

Remote Controlled Dog Training Collars

CONTENTS

OVERVIEW

MAIN FEATURES

SAFETY FEATURES

PACKAGE CONTENTS

DESCRIPTION OF TRANSMITTER PARTS

DESCRIPTION OF COLLAR PARTS

CHARGING THE RECEIVER/COLLAR

How th Change the Length of the Contact Points

INSTALLATION

ADDITIONAL PARTS

WIRE SPLICING

OPTIONAL ACCESSORIES

TROUBLESHOOTING

GENERAL MAINTENANCE TIPS

WARRANTY AND REPAIR INFORMATION

OVERVIEW

The Dogtra E-Fence 3500 system gives you the ability to allow your dog the freedom he

wants within your specified boundaries. Dogtra’

the use of conventional fencing that can be chewed through, jumped over or dug under.

The width of the signal field can easily be adjusted at the wall-mount transmitter. The strength of the

electrical stimulation can be adjusted on each separate receiver with the intensity selection dial. In the

“Stimulation Only”mode, your dog will receive stimulation only. In the “Pager +

Stimulation”mode, your dog will receive a silent pager/vibration, followed by stimulation

when he approaches the boundary area. In the “Pager Only”mode, you dog will receive and

non-stimulating pager/vibration only.

Once your dog consistently avoids the signal boundary, the stainless steel contact points

can be replaced with the plastic training probes. With the plastic training probes, your dog

will be able to respond to the vibration warning without receiving any electrical stimulation.

s containment system contains your dog without

Accessories for the system such as additional wire, flags, lightning/surge protector, and the

European 220-volt battery charger, are available by calling Dogtra Company at 1-888-811-

9111.

MAIN FEATURES

· Wide range of stimulation for all breeds and temperaments

· Fully waterproof receiver/collar

· 8 intensity levels on the receiver/collar to control individual dog stimulation needs

· Non-stimulating High Performance Pager vibration warning before stimulation

· High Performance Pager vibration only mode

· Wire breakage light with audible warning tone

· Long range signal with 40 acres maximum area coverage

· Advanced filtering system to prevent interference from outside sources

· Expandable to multiple dogs

· 2-hour rapid charge Lithium Polymer batteriesork up to 40 acres).

SAFETY FEATURES

· Dogtra’s E-Fence 3500 system collars use state-of-the-art

microcomputer technology. The receiver/collar has an automatic control that limits the

stimulation to eight seconds.

· Dogtra’s filtering system prevents accidental activation from outside sources other than

your transmitter.

PACKAGE CONTENTS

·Wall-Mount Transmitter

·Receiver/collar

·Transmitter Power Adaptor (25-volt 500mA)

·Receiver/Collar Charger (5-volt 1A)

·Test Lamp

·Boundary Training Flags (50 ea.)

·20ga Underground Fence Wire (500 feet)

·Wire Splices (4 ea.)

·Ground Wire (green)

·Transmitter Mount Screws (2 ea.)

·Plastic Anchor (2 ea.)

·Enhanced Contact Points Male (2 ea.)

·Non-Stimulation Contact Points (2 ea.)

·Contact Point Extension Washer/Adjustment Tool(2 ea.)

·Owner’'s Manual

·Training Book

Description Of Transmitter Parts

ON/OFF & Function Selection Switch

The On/Off & function selection switch has three functions. When the toggle switch is in the

up position, the unit will give the dog a pager/vibration followed by stimulation correction.

When the toggle switch is in the down position, only a pager/vibration occurs (no

stimulation). The power is off when the toggle switch is set to the middle position.

Field Width Adjustment Knob

This knob controls the width of the signal field (the approximate distance from the

boundary wire to the location where the receiver/collar first activates). Turning the knob

clockwise increases the field width, giving your dog a wider area before the activation

begins. Turning it counter-clockwise decreases the signal field, thus giving the dog a shorter

area prior to activation.

ON/OFF Indicator Light

When the On/Off & function selection switch is either in the up or down position the

On/Off indicator light will be on, indicating that the power is on. When the switch is in the

middle position the light goes off, indicating that the power is off. The indicator light stays

on even if a fuse is blown.

Boundary Wire Indicator Light

When the wires are connected properly, the boundary wire continuity light will be on. In the

event that the E-Fence 3500 wire becomes damaged or disconnected, the light will

automatically turn off and the warning beep will sound.

Wire Connectors For Splicing

The easy-to-use push-release wire connectors let you instantly connect or disconnect the

boundary wire leads. Wires should be stripped approximately a half-inch before being

inserted intothe red connectors on the bottom of the wall mount transmitter.

The system comes with a ground wire to protect the unit in the event of lightning/power

surge. Strip about a half-inch on each end of the ground wire and insert one end into the

black connector on the bottom of the wall transmitter. The other end should be buried into

the ground or wrapped around a water pipe and secured with electrical tape.

Option : A lightning/surge protector can be purchased if there are no grounding options

near the wall transmitter.

Adaptor Jack Connector

Plug the 120-volt adaptor into a 120-volt wall outlet and insert the adaptor plug into the

adaptor receptacle of the transmitter.

Wall-Mount Transmitter

Use the (2) included screws to mount the transmitter to a wall securely near an outlet. The

unit will withstand freezing temperatures, but it is not waterproof. Therefore, we recommend

mounting the transmitter in a safe, dry sheltered area such as a shed, garage or carport.

Plastic anchors have been provided to secure mounting onto drywall. Use a 1/4“drill bit to

make holes into the drywall. Insert the anchors into the holes so that the open end faces

out and mount the transmitter by inserting the screws into

the open end of the anchors.

To power the wall transmitter, plug the AC daptor into the standard 120-volt outlet and

connect it to the adaptor receptacle of the transmitter.

Description Of Reciver/Collar Parts