Dodge DR Ram SRT-10 2004, Ram SRT-10 2004 User Manual

SECTION PAGE
1
INTRODUCTION
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
4
UNDERSTANDING YOUR INSTRUMENT PANEL
5
STARTING AND OPERATING
6
WHAT TO DO IN EMERGENCIES
7
MAINTAINING YOUR VEHICLE
8
MAINTENANCE SCHEDULES
9
IF YOU NEED CONSUMER ASSISTANCE
TABLE OF CONTENTS
.............................................................3
..............................9
...................................121
.................................................149
..............................................195
...............................................213
..................................................261
.........................................279
1
2
3
4
5
6
7
8
9
10
INDEX
....................................................................289
10
CONTENTS
INTRODUCTION
1
Introduction ........................... 4
How To Use This Manual ..................4
Warnings And Cautions ................... 5
Van Conversions/Campers ................. 5
Vehicle Identification Number ............... 6
Vehicle Modifications / Alterations ........... 7
4 INTRODUCTION
INTRODUCTION
This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instruc­tions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold, so that the new owner will be aware of all safety warnings.
When it comes to service, remember that your dealer knows your vehicle best, has the factory-trained techni­cians and genuine Moparparts, and is interested in your satisfaction.
WARNING!
Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod­ucts of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
HOW TO USE THIS MANUAL
Consult the table of contents to determine which section contains the information you desire.
The detailed index, at the rear of this manual, contains a complete listing of all subjects.
INTRODUCTION 5
WARNINGS AND CAUTIONS
This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
VAN CONVERSIONS/CAMPERS
The Manufacturer’s Warranty does not apply to body modifications or special equipment installed by van conversion/camper manufacturers/ body builders. Such equipment includes video monitors, VCRs, heaters, stoves, refrigerators, etc. For warranty coverage and service on these items, contact the applicable manufac­turer.
Operating instructions for the special equipment in­stalled by the conversion/camper manufacturer should also be supplied with your vehicle. If these instructions are missing, please contact your selling dealer for assis­tance in obtaining replacement documents from the applicable manufacturer.
1
6 INTRODUCTION
VEHICLE IDENTIFICATION NUMBER
The vehicle identification number (VIN) is found on a stamped plate located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
NOTE: It is illegal to remove the VIN plate.
VEHICLE MODIFICATIONS / ALTERATIONS
WARNING!
Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
INTRODUCTION 7
1
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
CONTENTS
A Word About Your Keys ..................11
Key-In-Ignition Reminder ................11
Sentry Key If Equipped ................11
Ignition And Steering Lock If Equipped ......14
Manual Transmissions ...................14
Door Key .............................14
Door Locks ............................14
Power Door Locks .....................14
Remote Keyless Entry If Equipped .........17
2
To Unlock The Doors ...................18
To Lock The Doors .....................19
Using The Panic Alarm ..................20
Programming Additional Transmitters ........21
General Information ....................22
Transmitter Battery Service ...............23
Security Alarm System If Equipped .........24
Rearming Of The System .................24
To Set The Alarm ......................24
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
To Disarm The System ...................25
Windows .............................26
Power WindowsIf Equipped .............26
Sliding Rear Window ...................27
Wind Buffeting ........................27
Occupant Restraints ......................27
Lap/Shoulder Belts .....................28
Adjustable Upper Shoulder Belt Anchorage ....35
Automatic Locking Mode (If Equipped) ......36
Seat Belt Pretensioners ...................36
Enhanced Driver Seat Belt Reminder System
(BeltAlert) ...........................37
Seat Belts And Pregnant Women ............38
Seat Belt Extender ......................38
Driver And Right Front Passenger Supplemental
Restraint System (SRS)Airbag ............39
Child Restraint ........................49
Engine Break-In Recommendations ...........57
Safety Tips ............................58
Transporting Passengers .................58
Lock Your Vehicle ......................58
Exhaust Gas ..........................59
Safety Checks You Should Make Inside The
Vehicle ..............................60
Safety Checks You Should Make Outside The
Vehicle ..............................60
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11
A WORD ABOUT YOUR KEYS
The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to order duplicate keys from your dealer or a locksmith. If you received your keys without the bag, ask your dealer to give you the number.
Key-In-Ignition Reminder
If you open the drivers door when the key is in the ignition switch, a chime will sound to remind you to remove the key.
CAUTION!
An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended.
SENTRY KEY — IF EQUIPPED
With this system, an electronically coded ignition key sends a signal to the vehicle electronics. If the electronics recognizes the signal, the vehicle will start and continue to run. If the system does not recognize the signal the vehicle will start and run for a maximum of 2 seconds after the initial key ON. After six unsuccessful attempts at starting, the system will shut down until the correct key is used.
NOTE: The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Additional Sentry Keys or Mobil Speed-passdevices held against or immediately adjacent to the ignition key when starting the engine may cause vehicle starting problems. If a problem occurs, remove the Sentry Key from the key-ring and attempt to start the vehicle again. Pagers, cell phones, walkman, etc. will have no effect on this system.
2
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
The Security Light, located in the instrument cluster, will illuminate for about 2 seconds when the ignition switch is first turned to the ON position. If the vehicle electronics do not receive a valid signal from the ignition key, the Security Lightwill flash continuously to signal that the vehicle has been immobilized. If the Security Lightremains on during vehicle operation, it indicates a fault in the system electronics. If this option was ordered, all of the keys provided with your new vehicle have been programmed to the vehicle electronics.
Replacement Keys
NOTE: Only keys that have been programmed to the
vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it cannot be programmed to any other vehicle.
At the time of purchase, the original owner is provided with a four digit PIN number. This number is required for dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by using the Customer Key Programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed and needs to be cut.
NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13
Customer Key Programming
You can program new keys to the system if you have two valid keys by doing the following:
1. Insert the first valid key into the ignition and turn the ignition to the ON position for at least 3 seconds but no longer than 15 seconds. Turn the ignition back to the OFF position and remove the first key.
2. Insert the second valid key and switch the ignition to the ON position within 15 seconds. After 10 seconds the Security Lightwill begin to flash. Turn the ignition back to the OFF position and remove the second key.
3. Insert a blank Sentry Key into the ignition and switch the ignition to the ON position within 60 seconds of having removed the second key. After 10 seconds the Security Lightwill stop flashing, then turn on for 3 seconds; then turn off.
The new Sentry Key has been programmed. Repeat this process to program up to an additional 6 keys. A maxi­mum of 8 keys can be programmed to the system, including the original keys provided with the vehicle.
General Information
This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be received including interference that may cause undesired operation.
NOTE: Changes or modifications not expressly ap­proved by the party responsible for compliance could void the users authority to operate the equipment.
2
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
IGNITION AND STEERING LOCK IF EQUIPPED
Manual Transmissions
Depress and hold the release button located between the ignition switch and the instrument panel. Turn the igni­tion key to LOCK and remove the key.
Manual Transmissions
DOOR KEY
The same key used to start the vehicle is also used to unlock the doors. To unlock the vehicle doors, insert the key into the lock and turn.
To lock the doors, insert the key and turn.
DOOR LOCKS
Power Door Locks
WARNING!
For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15
WARNING!
When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal inju­ries and death.
NOTE: Vehicles equipped with remote keyless entry do
not have a passenger side door lock cylinder.
Vehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pressing the LOCK or UNLOCK buttons on the Remote Keyless Entry key fob (if equipped).
2
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Central Locking — If Equipped
Vehicles with security will have a feature called Central Locking. When the key is placed in the door cylinder and turned to the Unlockposition, the security will be disarmed, the illuminated entry will be turned on and that door will be mechanically unlocked. If the key is once again turned to the unlock position within 5 seconds of the first unlock, the remaining doors will unlock. If the key is turned to the Lockposition while all doors are closed, illuminated entry will be canceled, security will begin arming, and all doors will lock.
As a safety feature the doors will not lock when using the door lock switches during the following condition:
1. The drivers door is open while the key is in the ignition.
Automatic Door Locks
If this feature is enabled, your door locks will lock automatically when the vehicles speed exceeds 15 mph.
This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure:
1. Enter your vehicle and close all doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17
2. Fasten your seat belt (Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure).
3. Place the key into the ignition.
4. Within 10 seconds cycle the key from the OFF position to the ON position four times; ending in the ON position ( Do not start the engine ).
5. Within 30 seconds, press the drivers door lock switch in the LOCK direction.
6. A single chime will be heard to indicate the feature has been disabled.
7. To reactivate this feature, repeat the above steps.
8. If a chime is not heard, program mode was canceled before the feature could be disabled. If necessary, repeat the above procedure.
REMOTE KEYLESS ENTRY IF EQUIPPED
2
This system allows you to lock or unlock the doors from distances up to about 23 feet (7 meters) using a hand held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
To unlock the doors:
Press and release the UNLOCK button on the key fob once to unlock only the drivers door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and if installed, the cargo lamp will turn on for 30 seconds.
The system can be programmed to unlock all the doors upon the first UNLOCK button press by using the following procedure:
1. Enter your vehicle and close all doors.
2. Fasten your seat belt.(Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure).
3. Place the key into the ignition.
4. Turn the ignition to the ON position ( Do not start the engine ).
5. Press and hold the UNLOCK button on a programmed (i.e. functional) key fob.
6. Continue to hold the UNLOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the LOCK button.
7. When a single chime is heard, release both buttons.
8. Turn the ignition to the OFF position or wait 60 seconds.
9. To reactivate this feature, repeat the above steps.
10. If a chime is not heard, program mode was canceled before the feature could be changed. If necessary, repeat the above procedure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19
To lock the doors:
Press and release the LOCK button on the transmitter to lock all doors. If the ignition is OFF, when the doors are locked, the parking lights will flash on once and the horn will chirp once.
The horn chirp feature will be shipped from the assembly plants activated. If desired this feature can be disabled by using the following procedure:
1. Enter your vehicle and close all doors.
2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this program­ming procedure).
3. Place the key into the ignition.
4. Turn the ignition to the ON position ( Do not start the engine ).
5. Press and hold the LOCK button on a programmed (i.e. functional) key fob.
6. Continue to hold the LOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the UNLOCK button.
7. When a single chime is heard, release both buttons.
8. Turn the ignition to the OFF position or wait 60 seconds.
9. Test the horn chirp feature by pressing the LOCK button on the key fob with the ignition in the OFF position, or the key removed.
10. To reactivate this feature, repeat the above steps.
Vehicles will be shipped from the assembly plants with the park lamp flash feature activated. If desired, this feature can be disabled by using the following procedure:
1. Enter your vehicle and close all doors.
2
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this program­ming procedure).
3. Place the key into the ignition.
4. Turn the ignition to the ON position ( Do not start the engine ).
5. Press and hold the LOCK button on a programmed (i.e. functional) key fob.
6. Continue to hold the LOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the PANIC button.
7. When a single chime is heard, release both buttons.
8. Turn the ignition to the OFF position or wait 60 seconds.
9. Test the park lamp flash feature by pressing the LOCK button on the key fob with the ignition in the OFF position or the key removed.
10. To reactivate this feature, repeat the above steps.
11. If a chime is not heard, program mode was canceled before the feature could be disabled. If necessary, repeat the above procedure.
Using the Panic Alarm
To activate the Panic mode while the ignition is OFF press and release the PANIC button on the transmitter once. When the Panic mode is activated, the interior lights will illuminate, the headlamps and parking lights will flash, and the horn will sound.
To cancel the Panic mode press and release the PANIC button on the transmitter a second time. Panic mode will automatically cancel after 3 minutes or if the vehicle is started and exceeds 15 mph. During the Panic Mode, the door locks and remote keyless entry systems will func­tion normally. Panic mode will not disarm the security system on vehicles so equipped.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21
Programming Additional Transmitters
Vehicles with the keyless entry option will be shipped from the assembly plants with two key fob transmitters programmed only for that vehicle. Atotal of four fobs can be programmed for your vehicle. Additional fobs can be programmed to your vehicle through the use of a cur­rently programmed fob.
NOTE: When entering program mode using that fob, ALL currently programmed fobs will be erased and you will have to reprogram them for your vehicle. However, if program mode is entered and no action is performed, the previously programmed fobs will continue to func­tion.
1. Enter your vehicle and close all doors.
2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this program­ming procedure).
3. Place the key into the ignition.
4. Turn the ignition to the ON position ( Do not start the engine ).
5. Press and hold the UNLOCK button on a programmed (i.e. functional) key fob.
6. Continue to hold the UNLOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the PANIC button.
7. When a single chime is heard, release both buttons. The chime indicates that the system is in program mode.
8. Press and release both the LOCK and UNLOCK buttons, simultaneously on the fob to be programmed.
9. A single chime will be heard. The chime indicates that the fob has been recognized.
10. Within 4 seconds of hearing the chime, press and release any button on the fob being programmed.
2
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
11. A single chime will be heard. The chime indicates that the fob has been programmed.
12. Repeat steps 8 to 11 for a total of 4 fobs.
13. Turn the ignition to the OFF position or wait 60 seconds to exit program mode.
14. Your vehicle will remain in program mode for up to 60 seconds from when the original chime (i.e. Step #7) was heard. After 60 seconds, all programmed fobs will function normally.
NOTE: If you do not have a programmed transmitter, contact your dealer for details.
General Information
This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be received including interference that may cause undesired operation.
NOTE: Changes or modifications not expressly ap­proved by the party responsible for compliance could void the users authority to operate the equipment.
If your Keyless Entry Transmitter fails to operate from a normal distance, check for these two conditions.
1. Weak batteries in transmitter. The expected life of the batteries is from one to two years.
2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23
Transmitter Battery Service
The recommended replacement battery is a 3V lithium 2016 cell. This transmitter requires two batteries.
NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board.
1. With transmitter buttons facing down, use a flat blade or dime to pry the two halves of the transmitter apart. Make sure not to damage the rubber gasket during removal.
2. Remove and replace the batteries. Be careful not to disturb the metal terminal near the batteries. Install the batteries with the positive terminal up, reference the note + SIDE UPon the inside of the bottom half of the transmitter case. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol.
3. To reassemble the transmitter case snap the two halves together. Make sure there is an even gap between the two halves. Test transmitter operation.
2
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
SECURITY ALARM SYSTEM IF EQUIPPED
This system monitors the vehicle doors and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visual signals. For the first 3 minutes the horn will sound and the headlights and security telltale will flash repeatedly. For an addi­tional 15 minutes only the headlights and security telltale will flash. The engine will run only if a valid Sentry Key is used to start the vehicle. Use of the Sentry Key will disable the alarm.
Rearming of the System:
The security system will rearm itself after the 15 addi­tional minutes of headlights and security telltale flashing, if the system has not been disabled. If the condition which initiated the alarm is still present, the system will ignore that condition and monitor the remaining doors and ignition.
To Set the Alarm:
The alarm will set when you use the power door locks, turn the key in the drivers door lock cylinder, or use the Keyless Entry transmitter to lock the doors. After all the doors are locked and closed the SECURITY light in the instrument cluster will flash rapidly to signal that the system is arming. The security light in the instrument panel cluster will flash rapidly for about 16 seconds to indicate that the alarm is being set. After the alarm is set, the security light will flash at a slower rate to indicate that the system is armed.
NOTE: If the SECURITY light stays on continuously during vehicle operation, have the system checked by your dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25
To Disarm the System:
Use the Keyless Entry transmitter or the key to turn the drivers door lock to the unlock position. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds. Check the vehicle for tampering.
The Security system will also disarm, if the vehicle is started with a programmed Sentry Key. If an unpro­grammed Sentry Key is used to start a vehicle, the engine will run for 2 seconds and then the security alarm will be initiated. To exit alarming mode, press the transmitter Unlock button, unlock the drivers door using the key cylinder, or start the vehicle with a programmed Sentry Key.
The Security Alarm System is designed to protect your vehicle; however, you can create conditions where the system will arm unexpectedly. If you remain in the vehicle and lock the doors with the transmitter, the alarm will sound when you pull the door handle to exit. You may also accidentally disarm the system by unlocking the drivers door with the door key and then locking it manually with the lock plunger. The door will be locked but the Security Alarm will not arm.
2
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
WINDOWS
Power WindowsIf Equipped
The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control. The windows will operate only when the ignition switch is turned to the ON or ACC (Accessory) position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27
Auto Down (Drivers Side Only)
The drivers window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically.
Sliding Rear Window
A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window.
WIND BUFFETING
Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear sliding glass open, open the front and rear sliding glass together to minimize the buffeting.
OCCUPANT RESTRAINTS
Some of the most important safety features in your vehicle are the restraint systems. These include the belts for the driver and all passengers, front airbags for both the driver and front passenger and, if so equipped, window bags for the driver and passengers seated next to a window. If you will be carrying children too small for adult-size belts, your seat belts also can be used to hold infant and child restraint systems.
Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible.
2
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
WARNING!
In a collision, you and your passengers can suffer much greater injuries if you are not properly buck­led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly.
Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street.
Research has shown that seat belts save lives, and that they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times.
Lap/Shoulder Belts
All seating positions have combination lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29
WARNING!
It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Be sure everyone in your vehicle is in a seat and using a seat belt properly.
WARNING!
Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instruc­tions to wear your seat belt safely and to keep your passengers safe, too.
Two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size.
2
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Lap/Shoulder Belt Operating Instructions
1. Enter the vehicle and close the door. Sit back and adjust the seat.
2. The seat belt latch plate is above the back of the seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31
WARNING!
A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you.
A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
A belt that is worn under your arm is very danger­ous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. And a belt worn under the arm can cause internal injuries. Ribs arent as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision.
A shoulder belt placed behind will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together.
4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
2
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
WARNING!
A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces wont be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos­sible and keep it snug.
A twisted belt cant do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you cant straighten a belt in your vehicle, take it to your dealer and have it fixed.
5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt.
6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully.
WARNING!
A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.) or if the airbag deployed.
Standard Cab Front Center Three Point Belt
1. The front center seat belt on the Standard Cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger seat. Insert the vehicle ignition key into the center white slot on the black buckle. The black buckle latch plate can be removed when the key is pressed into the buckle. Allow the retractor to take up the surplus webbing, and the buckles will hang vertically from the cab back exit bezel, thus freeing up all the area behind the front seats.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33
2
Detaching Buckle with
2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible click. Refer to the previous section for the proper seat belt usage.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
WARNING!
If the black latch and black buckle are not prop­erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision.
When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted. If the webbing is twisted, follow the preceding procedure to detach the black latch and black buckle, untwist the webbing, and reattach the black latch and black buckle.
Inserting Latch Plate
In Use Position
WARNING!
If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35
Adjustable Upper Shoulder Belt Anchorage
In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Press the button located on the upper belt guide, and then move it up or down to the position that serves you best.
2
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, youll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
Automatic Locking Mode (if Equipped)
In this mode, the shoulder belt is automatically pre­locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is only available on the front passenger side belt.
When To Use The Automatic Locking Mode
Anytime a child safety seat is installed in a passenger front seating position. Children 12 years old and under should be properly restrained in the rear seat whenever possible.
How To Use The Automatic Locking Mode
1. Buckle the combination lap and shoulder belt.
2. Grasp the shoulder portion and pull downward until the entire belt is extracted.
3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
How To Disengage The Automatic Locking Mode
Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic lock­ing mode and activate the vehicle sensitive (emergency) locking mode.
Seat Belt Pretensioners
The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove any slack from the seat belt system in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37
NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly.
The pretensioners are triggered by the airbag control module. Like the airbags, the pretensioners are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced.
Enhanced Driver Seat Belt Reminder System (BeltAlert)
If the drivers seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts. Once the warning is triggered, the Enhanced Warning System (BeltAlert) will continue to chime and flash the Seat Belt Warning Light for 96 seconds or until the drivers seat belt is buckled. The Enhanced Warning System (BeltAlert) will be reactivated
if the drivers seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h).
The Enhanced Warning System (BeltAlert) can be en­abled or disabled by your authorized dealer or by following these steps:
NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON position. DaimlerChrysler does not recommend deacti­vating the Enhanced Warning System (BeltAlert).
NOTE: If the drivers door is open a continuous chime will sound and override the single chime.
1. Turn the ignition switch to the OFF position and buckle the drivers seat belt.
2. Start the engine and wait for the Seat Belt Warning Light to turn off.
2
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the drivers seat belt at least three times within 10 seconds, ending with the seat belt buckled.
4. Turn off the engine. A single chime will sound to signify that you have successfully completed the pro­gramming.
The Enhanced Warning System (BeltAlert) can be reacti­vated by repeating this procedure.
NOTE: Although the Enhanced Warning System (BeltA­lert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the drivers seat belt remains unbuckled.
Seat Belts and Pregnant Women
We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe.
Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.
Seat Belt Extender
If a seat belt is too short, even when fully extended, your dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the ex­tender and store it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39
WARNING!
Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.
Driver And Right Front Passenger Supplemental Restraint System (SRS)Airbag
This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The drivers front airbag is mounted in the center of the steering wheel. The passengers front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
These airbags are certified to the new Federal regulations that allow less forceful deployments.
2
This vehicle may also be equipped with window bags to protect the driver and passengers sitting next to a win­dow. If the vehicle is equipped with window bags, they are located above the side windows. Their covers are also labeled SRS AIRBAG.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
WARNING!
Do not put anything on or around the airbag covers or
attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
Do not mount any aftermarket equipment such as trailer
brake controllers, snowplow controllers, auxiliary light switches, radios, etc. on or behind the knee bolster. Knee bolsters are designed to work with the air bag and seat belt to protect you. Mounting any additional equip­ment on or behind the knee bolster can cause injury during a crash.
If your vehicle is equipped with window bags, do not
stack luggage or other cargo up high enough to block the location of the window bag. The area where the window bag is located should remain free from any obstructions.
If your vehicle is equipped with window bags, do not
have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that require permanent attachments (bolts or screws) for installation on the vehicle roof. Do not drill into the roof of the vehicle for any reason.
Airbags inflate in moderate to high speed impacts. Along with the seat belts, front airbags work with the instru­ment panel knee bolsters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection.
The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions. If your vehicle is so equipped, the window bag on the crash side of the vehicle is triggered in moderate to severe side collisions. In certain types of collisions, both the front and side airbags may be triggered. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly.
Here are some simple steps you can follow to minimize the risk of harm from a deploying airbag.
Children 12 years and under should ride buckled up in a rear seat, if available.
Infants in rear facing child restraints must NEVER ride in the front seat of a vehicle with a passenger front airbag unless the airbag is turned off (Standard Cab Vehicles Only). An airbag deployment can cause se­vere injury or death to infants in that position. See the Passenger Airbag On/Off Switch section.
If your vehicle does not have a rear seat, see the Passenger Airbag On/Off Switch section.
Children that are not big enough to properly wear the vehicle seat belt (see section on Child Restraints) should be secured in belt-positioning booster seats. Never allow children to slide the shoulder belt behind them or under their arm.
All occupants should use their seat belts properly.
The driver and front passenger seats should be moved back as far as practical to allow the airbag room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41
WARNING!
Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags wont deploy at all. Always wear your seat belts even though you have airbags.
Being too close to the steering wheel or instru­ment panel during airbag deployment could cause serious injury. Airbags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel.
If the vehicle has window airbags, they also need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat.
2
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Airbag System Components
The airbag system consists of the following:
Airbag Control Module
AIRBAG Readiness Light
Driver Airbag
Passenger Airbag
Steering Wheel and Column
Instrument Panel
Crash Sensor
Interconnecting Wiring
Knee Impact Bolsters
Passenger Side Frontal Airbag ON/OFF Switch (Stan­dard Cab Vehicles Only)
The Window Airbag System, on vehicles equipped, consists of the following:
AIRBAG Readiness Light (shared with the front airbag system)
Window Bags Above the Side Windows.
Airbag Control Module (shared with the front airbag system)
Side impact sensors
Interconnecting Wiring
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43
How The Airbag System Works
The airbag control module determines if a frontal
collision is severe enough to require the airbags to inflate.
The airbag control module will not detect roll over, or rear collisions.
The airbag control module also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the RUN position. These include all of the items listed above except the knee bolsters, the instrument panel, and the steering wheel and column. If the key is in the Offposition, in the ACC position or not in the ignition, the airbags are not on and will not inflate
The airbag control module also turns on the AIR BAG light in the instrument panel for 6 to 8 seconds when the ignition is first turned on, then turns the light off.
If it detects a malfunction in any part of the system, it turns on the light either momen-
tarily or continuously. The instrument cluster will flash the seat belt indicator if it detects a fault with the airbag indicator.
WARNING!
Ignoring the AIR BAG light in your instrument panel could mean you wont have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
2
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
When the airbag control module detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the airbags. The airbag covers separate and fold out of the way as the airbags inflate to their full size. The airbags fully inflate in milliseconds. This is less time than it takes you to blink your eyes. The airbags then quickly deflate while helping to restrain the driver and front passenger. The drivers front airbag deflates through vents towards the instrument panel. The passengers front airbag is deflated through vent holes in the sides of the airbag. In this way the airbags do not interfere with your control of the vehicle.
The knee impact bolsters help protect the knees and position you for the best interaction with the front airbag.
Passenger Airbag On/Off Switch – (Standard Cab Vehicles Only)
The passenger front airbag is to be turned off only if the passenger:
is an infant (less than 1 year old) who must ride in the front seat because there is no rear seat, or because the infant has a medical condition which makes it neces­sary for the driver to be able to see the infant,
is a child, age 1 to 12 who must ride in the front seat because there is no rear seat, because there is no rear seat position available, or because the child has a medical condition which makes it necessary for the driver to be able to see the child,
has a medical condition which makes passenger airbag inflation (deployment) a greater risk for the passenger than the risk of hitting the dashboard (instrument panel) or windshield in a crash.
WARNING!
Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash. This may result in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45
To Shut Off the Passenger Airbag (Standard Cab Ve­hicles Only)
Place the ignition key in the Passenger Airbag On/Off Switch, push the key in and turn clockwise, and remove the key from the switch. This will shut off the passenger side airbag. The Offlight near the switch will illumi­nate when the ignition switch is turned to the ON position.
To Turn On the Passenger Airbag (Standard Cab Ve­hicles Only)
Place the ignition key in the Passenger Airbag On/Off Switch, push the key in and turn counterclockwise, and remove the key from the switch. This will turn on the passenger airbag. The Offlight near the switch will be off when the ignition switch is turned to the ON position.
2
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
If A Deployment Occurs
The airbag system is designed to deploy when the air bag control module detects a moderate-to-severe frontal col­lision, and then immediately to deflate.
NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system.
If you do have a collision which deploys the airbags, any or all of the following may occur:
The nylon airbag material may sometimes cause abra­sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly.
However, if you havent healed significantly within a few days, or if you have any blistering, see your doctor immediately.
As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturers instruc­tions for cleaning.
It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47
WARNING!
Deployed airbags cant protect you in another colli­sion. Have the airbags replaced by an authorized dealer as soon as possible.
Window Airbags Supplemental Restraint System (SRS)If Equipped
The window airbag control module determines if a side collision is severe enough to require the side airbags to inflate. The window airbag control module will not detect roll over, front or rear collisions.
The airbag control module monitors the readiness of the electronic parts of the system whenever the ignition switch is in the RUNposition. These include all of the items listed above. The airbag control module also turns on the AIRBAG light in the instrument panel for 6 to 8
seconds when the ignition is first turned on as a diag­nostic or system check, then turns the light off. If it detects a malfunction in any part of the system, it turns on the light either momentarily or continuously.
The side (window) impact SRS Airbags are designed to activate only in certain side collisions. When the airbag control module detects a collision requiring the window bags to inflate, it signals the inflators on the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the window bag. The inflating window bag pushes the side pillar molding out of the way and covers the window. The airbag inflates in about 30 milliseconds (about one-quarter of the time it takes to blink your eyes) with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the window bag inflates. This especially applies to
1
children. The window bag is only about 3
⁄2inches (8.9
cm) thick when it is inflated.
2
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Enhanced Accident Response System
If the airbags deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically. In addition, approximately 10 seconds after the vehicle has stopped moving, the interior lights will light until the ignition switch is turned off.
Maintaining Your Airbag Systems
WARNING!
Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body struc­ture, or frame.
You need proper knee impact protection in a collision. Do not mount or locate any aftermarket equipment on or behind the knee bolster.
It is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49
Airbag Light
You will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system promptly:
The airbag light does not come on or flickers during the 6 to 8 seconds when the ignition switch is first turned on.
The light remains on or flickers after the 6 to 8 second interval.
The light flickers or comes on and remains on while driving.
NOTE: If the speedometer, tachometer or any engine related gauges are not working, the airbag control mod­ule may also be disabled. The airbags may not be ready
to inflate for your protection. Promptly check fuse num­bers 52 and 53 in the fuse and relay center. See your dealer if the fuse is good.
Child Restraint
Everyone in your vehicle needs to be buckled up all the time babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
Children 12 years and under should ride properly buck­led up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.
2
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
WARNING!
In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the childs size.
Infants and Small Children
There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Use the restraint that is correct for your child:
Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types
of child restraints can be used rearward-facing: infant carriers and convertiblechild seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt.
The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). Convertiblechild seats can be used either rearward-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 20 lbs (9 kg) but are less than one year old.
Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position.
Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt.
The belt-positioning booster seat is for children weigh­ing more than 40 lbs (18 kg), but who are still too small to fit the vehicles seat belts properly. If the child cannot sit with knees bent over the vehicles seat cushion while the childs back is against the seat back, they should use a belt-positioning-booster seat. The child and booster seat are held in the vehicle by the lap/shoulder belt. (Some booster seats are equipped with a front shield and are held in the vehicle by the lap portion.) For further information refer to www.seatcheck.org.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51
WARNING!
Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturers directions ex­actly when installing an infant or child restraint.
A rearward facing child restraint should only be used in the front seat if the passengers front airbag is Off. If the airbag is left On, a rearward facing child restraint in the front seat may be struck by a deploying passenger airbag which may cause severe or fatal injury to the infant.
2
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Here are some tips for getting the most out of your child restraint:
Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it before you buy it.
The restraint must be appropriate for your childs weight and height. Check the label on the restraint for weight and height limits.
Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it.
The passenger seat belts are equipped with either cinching latch plates or switchable seat belt retractors, which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip.
If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary.
If the seat belt has a switchable retractor, it will have a distinctive label: Pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then pull on the belt until it is all removed from the retractor. Allow the belt to return to the retractor, pulling on the excess webbing to tighten the lap portion about the child restraint. Refer to the Automatic Locking Modeearlier in this section.
If the belt still cant be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still cant make the child restraint secure, try a different seating position.
Buckle the child into the seat according to the child restraint manufacturers directions.
When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seat backs and cause serious personal injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53
WARNING!
Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturers directions exactly when install­ing an infant or child restraint.
Lower Anchors and Tether for CHildren (LATCH)
Each vehicle is equipped with the child restraint anchor­age system called LATCH, which stands for Lower Anchors and Tether for CHildren. LATCH child restraint anchorage systems are installed in the Standard Cab passenger seat position and feature tether strap anchor­ages, which must be used, located behind the seatback (refer to Child Restraint Tether Anchor later in this section).
2
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
The LATCH lower anchorage bars are located where the seatback meets the seat cushion. If the lower anchorage bars are not visible, identification dots are located above the standard cab front seat lower anchorages as a guide for locating the lower anchors.
NOTE: For children riding in the front seat of a Stan­dard Cab model refer to the Passenger Airbag On/Off Switchlocated in this section.
Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products.
Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchor­ages will continue to have features for installation in vehicles using the lap or lap/shoulder belt. They will also have tether straps, and you are urged to take advantage of all of the available attachments provided with your child restraint in any vehicle.
NOTE: If your child restraint seat is not LATCH com­patible, install the restraint using the vehicle seat belting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55
Installing the Child Restraint System
We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Many, but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or connector and a means for adjusting the tension in the strap. Forward-facing toddler restraints and some rearward-facing infant restraints will also be equipped with a tether strap, a hook and means for adjusting the tension in the strap.
In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages. Then tighten all three straps as you push the child restraint rearward and downward into the seat.
Not all child restraint systems will be installed as we have described here. Again, carefully follow the instruc­tions that come with the child restraint system.
WARNING!
Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturers directions exactly when installing an infant or child restraint.
Child Restraint Tether Anchor
Child restraints having tether straps and hooks for con­nection to tether anchors have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for their older products. Regular Cab models of Ram Pickups have two tether anchorages, one each behind the front center and right seats.
2
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
WARNING!
An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Follow the instructions below. See your dealer for help if nec­essary.
Tether Anchorage Points at the Right and Center Front Seat (Regular Cab - All Seats)
1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor directly behind the seat.
2. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal.
3. Install the child restraint and remove the slack in the tether strap according to the manufacturers instructions.
Regular Cab With
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57
Children Too Large for Booster Seats
Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat.
Make sure that the child is upright in the seat.
The lap portion should be low on the hips and as snug as possible.
Check belt fit periodically. A childs squirming or slouching can move the belt out of position.
If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back.
ENGINE BREAK-IN RECOMMENDATIONS
The engine in your new SRT-10 does not require a long break-in period. Following these few simple guidelines is all that is necessary for a good break-in:
For the first 500 miles (800 km):
Keep your vehicle speed below the legal, posted speed limit and your engine speed below 4,000 rpm.
Avoid driving at a constant speed, either fast or slow, for long periods of time.
Do not make any full throttle starts and avoid full throttle acceleration.
Use the proper gear for your speed range.
2
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Wait until the engine has reached normal operating temperature before driving at the recommended maxi­mum break-in speed.
Avoid excessive idling.
Check the engine oil level at every fuel fill.
NOTE: A new engine will consume some oil during the first few thousand miles of operation. This should be considered as a normal part of the break-in and not interpreted as a sign of difficulty.
WARNING!
It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Be sure everyone in your vehicle is in a seat and using a seat belt properly.
SAFETY TIPS
Transporting Passengers
This vehicle is designed to carry passengers in the cab only. For safety reasons, NEVER TRANSPORT PASSEN­GERS IN THE CARGO AREA.
Lock Your Vehicle
Always remove the keys from the ignition and lock all doors when leaving the vehicle unattended, even in your own driveway or garage. Try to park your vehicle in a well-lighted area and never invite theft by leaving ar­ticles of value exposed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59
Exhaust Gas
WARNING!
Exhaust gases contain carbon monoxide, a poten­tially toxic gas that by itself is colorless and odorless. To avoid inhaling these gases, the following precau­tions should be observed:
Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
If it is necessary to sit in a parked vehicle with the engine running for more than a short period, adjust your climate control system to force outside air into the vehicle. Set the blower at high speed and the controls in any position except OFF or MAX A/C.
The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
Be aware of changes in the sound of the exhaust system; exhaust fumes detected inside the vehicle; or damage to the underside or rear of the vehicle. Have a competent mechanic inspect the complete exhaust system and adja­cent body areas for broken, damaged, deteriorated or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace or adjust as required.
2
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Safety Checks You Should Make Inside The Vehicle
Seat Belts
Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.
Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.) or if the front airbags have deployed. If there is any question regarding belt or retractor condition, replace the belt.
Airbag Light
The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see you authorized dealer. If the light stays on, flickers or comes on while driving, have the system checked by an autho­rized dealer. If there is a problem with the airbag light the seatbelt light will flash.
Safety Checks You Should Make Outside The Vehicle
Tires
Examine tires for tread wear or uneven wear patterns. Check for stones, nails, glass or other objects lodged in the tread.
Inspect for tread cuts or sidewall cracks. Check wheel nuts for tightness and tires for proper pressure.
Lights
Check the operation of all exterior lights. Check turn signal and high beam indicator lights on the instrument panel.
Door Latches
Check for positive closing, latching and locking.
Fluid Leaks
Check area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks. Also, if fuel fumes are detected the cause should be located and corrected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CONTENTS
Mirrors ...............................65
Phone Call Features ....................73
3
Automatic Dimming MirrorIf Equipped ....65
Outside Mirrors .......................65
Exterior Mirrors Folding Feature ...........66
Electronic Power Mirrors If Equipped ......66
Electric Rear Window Defroster And Heated
Sideview Mirrors If Equipped ...........67
Hands–Free Communication (UConnect™) — If
Equipped .............................67
Operation ............................69
Advanced Phone Connectivity .............75
UConnectSystem Features ..............77
Seats .................................79
40-20-40 Front Seat .....................80
Power Driver Seat ......................80
Manual Passenger Seat ..................82
Manual Seatback Recline .................83
Adjustable Head Restraints ...............84
62 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
To Open And Close The Hood ..............84
Lights ................................86
Interior Lights ........................86
Battery Saver .........................87
Headlamp Delay If Equipped ...........88
Headlights, Parking Lights, Panel Lights ......88
Daytime Running Lights (Canada And Fleet
Vehicles Only) ........................89
Lights-On Reminder ....................89
Fog Lights ...........................89
Cargo Light ..........................90
Multifunction Control Lever ................90
Turn Signals ..........................90
Passing Light .........................91
High Beam / Low Beam Select Switch .......91
Windshield Wipers .....................92
Windshield Washers ....................93
Tilt Steering Column .....................94
Driver Adjustable Pedals ..................95
Adjustment ..........................95
Electronic Speed Control ...................96
To Activate ...........................96
To Set At A Desired Speed ................97
To Deactivate .........................97
To Resume Speed ......................97
To Vary The Speed Setting ................97
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 63
To Accelerate For Passing ................98
Overhead Console .......................99
Courtesy/Reading Lights .................99
Compass/Temperature Mini-Trip Computer ....100
US/M Button ........................100
Reset Button .........................101
Global Reset .........................101
Step Button .........................101
Average Fuel Economy (AVG ECO) ........102
Distance To Empty (DTE) ...............102
Trip Odometer (ODO) ..................102
Elapsed Time (ET) .....................103
C/T Button .........................103
Automatic Compass Calibration ...........103
Manual Compass Calibration .............104
To Put Into a Calibration Mode ...........104
Outside Temperature ...................105
Garage Door Opener ....................106
Programming Homelink ................107
Canadian Programming/Gate Programming . . 109
Using Homelink ......................110
Erasing Homelink Buttons ...............110
Reprogramming a Single Homelink Button . . . 111
Security ............................111
Electrical Power Outlets ..................112
Cigar Lighter And Ash Receiver ............113
3
64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Cupholders ...........................114
Front Cupholders .....................114
Storage ..............................114
Center Storage Compartment .............114
Storage And Seats .....................115
Pickup Box ...........................116
Slide-In Campers .......................118
Easy-Off Tailgate .......................118
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65
MIRRORS
Automatic Dimming MirrorIf Equipped
This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated.
CAUTION!
To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
Outside Mirrors
To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.
3
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING!
Vehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with an­other vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side convex mirror. Some vehicles will not have a convex right side mirror.
Exterior Mirrors Folding Feature
All exterior mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions; full forward, full rearward, and normal.
Electronic Power Mirrors If Equipped
The controls for the power mirrors are located on the drivers door trim panel.
Set the top switch to the left or right for the left or right mirror, and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror. To adjust a mirror, select left or right with the top switch, and press one of the four arrows for the direction you want the mirror to move.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67
Electric Rear Window Defroster and Heated Sideview Mirrors If Equipped
The Electric Rear Window Defroster and Heated
side view mirrors are activated by pressing the heated grid button, located on the Climate Control panel, with the ignition On. Turning Off the ignition will deactivate the Electric Rear Window Defroster and Heated side view mirrors feature. These features also turn off after activation, when 15 minutes have elapsed. To reactivate, simply press the button again.
HANDS–FREE COMMUNICATION (UConnect) IF EQUIPPED
UConnectis a voice-activated, hands-free, in-vehicle communications system. UConnect; allows you to dial your cellular phone using simple voice commands (e.g., Callor Dial). Your cellular phones audio is trans- mitted through your vehicles stereo system; the system will automatically mute your radio before receiving or sending a call.
3
68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UConnectallows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the systems micro­phone for private conversations.
The UConnect; phone book enables you to store up to 32 names and four numbers per name. This system is driven through your BluetoothHands-Free Profile cellular phone. UConnectfeatures Bluetoothtechnol­ogy - the global standard that enables different electronic devices to connect to each other without wires or a docking station, so UConnectworks no matter where you stow your cellular phone (be it your purse, pocket, or briefcase). UConnectallows up to seven cellular phones to be linked to the system, and it is available in English, French, or Spanish formats (as equipped).
The rearview mirror contains the microphone for the system and the control buttons that will enable you to
access the system. The diagram below shows the mirror with the appropriate buttons. Individual button behavior is discussed in the OperationSection.
The UConnectsystem can be used with any Hands Free Profile certified Bluetoothcellular phone. If your cellular phone has a different profile (i.e. headset profile), you will not be able to use any UConnectfeatures.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69
The UConnectsystem is fully integrated into your vehicle, including your vehicles stereo system. All voice prompts as well as the other partys voice in a conversa­tion will be played over your vehicles stereo system. The volume of the UConnectsystem can be controlled through your normal stereo controls.
The radio display will be used for visual prompts from the UConnectsystem such as caller ID.
Operation
Voice commands can be used in the operation of the UConnectsystem and to navigate through the UCon­nectmenu structure. Voice commands should be given after each UConnectsystem prompt. You will be prompted for a specific command and then guided through the available options. There are two ways to give commands to the UConnectsystem:
You can say Dialat the Readyprompt. When prompted for the phone number you wish to dial, say the phone number (123 456 7890).
Alternatively as you become familiar with the UCon­nectsystem, you can combine the commands and say Dial 123 456 7890.
Pairing a Cellular Phone to the UConnectSystem
To begin using your UConnectsystem, you must pair your compatible Bluetoothenabled cellular phone. To complete the registration process, you will need to refer­ence your cellular phone owners manual.
Press the Phonebutton to begin.
After the Readyprompt, say Setup.
When prompted, say Phone Pairing.
You will be asked to say a four-digit pin number into the UConnectsystem which you will later need to
3
70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
enter into your cellular phone during the cellular phone pairing process. You can enter any four-digit pin number. You will not need to remember this pin number after the initial registration process.
The UConnectsystem will then prompt you to begin the cellular phone pairing process on your cellular phone. Please see your cellular phone users manual for instructions on how to complete this step.
For identification purposes, you will be prompted to give the UConnectsystem a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name.
You will then be asked to give your cellular phone a priority level between 1 and 7, 1 having the highest priority. You can connect up to seven cellular phones to your UConnectsystem and the priority allows the UConnectsystem to know which cellular phone to use if multiple cellular phones are in the vehicle at the
same time. For example, if a priority 3 and priority 5 cellular phone are both in the vehicle, the UConnect system will use the priority 3 cellular phone when you make a call. You can select to use a lower priority cellular phone at any time.
Making a Phone Call Using Digit Dialing
Press the Phonebutton to begin.
After the Readyprompt, say Dialor Callfollowed by the phone number you wish to dial. For example, you can say Dial 123 456 7890. The phone number that you enter must be a valid length.
Making a Phone Call Using Your UConnect Phonebook
Press the Phonebutton to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71
After the Readyprompt, say Dialor Callfollowed by the name and designation of a phonebook entry that you wish to dial. For example, you can say Call John Doe Work.
Add Names to Your UConnectPhonebook
Press the Phonebutton to begin.
After the Readyprompt, say Phonebook New Entry.
Or, After the Readyprompt, say Phonebook.
When prompted, say New Entry.
When prompted, say the name of the new entry.
Next, enter the number designation (e.g. Home”, “Work”, “Mobile”,or“Pager). This will allow you to
have multiple numbers for each phonebook entry.
Recite the phone number for the phonebook entry that you are adding.
After you are finished adding an entry into the phone­book, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu.
The UConnectsystem will allow you to enter up to 32 names into the phonebook with each name having up to four associated phone numbers and designations.
Edit Entries in the UConnectPhonebook
Press the Phonebutton to begin.
After the Readyprompt, say Phonebook Edit.
You will then be asked for the name of the phonebook entry that you wish to edit.
Next, choose the number designation that you wish to edit. The choices are home, work, mobile, or pager.
Recite the new phone number for the phonebook entry that you are editing.
3
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu.
Phonebook edit can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number, but you can add John Does work number later through phonebook edit.
Delete Entries in the UConnectPhonebook
Press the Phonebutton to begin.
After the Readyprompt, say Phonebook Delete.
After you enter the phonebook delete menu, you will then be asked for the name of the phonebook entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say List Namesto hear a list of the entries in the
phonebook from which you can choose. To select one of the entries from the list, press the Voice Recogni­tionbutton while the UConnectsystem is playing the desired entry and say Delete.
After you enter the name, the UConnectsystem will ask you if you wish to delete the home, work, mobile, or pager number for this entry.
Delete All Entries in the UConnectPhonebook
Press the Phonebutton to begin.
After the Readyprompt, say Phonebook Delete All.
The UConnectsystem will ask you to verify that you wish to delete all the entries from the phonebook.
After confirmation, the phonebook entries will be deleted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73
List All Names in the UConnectPhonebook
Press the Phonebutton to begin.
After the Readyprompt, say Phonebook List Names.
The UConnectsystem will play the names of all the phonebook entries.
To call one of the names in the list, press the Voice Recognitionbutton during the playing of the desired name and say Call.
The UConnectsystem will then prompt you as to number designation you wish to call.
The selected number will be dialed.
Phone Call Features
The following feature(s) can be accessed through the UConnectsystem if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the UConnectsystem.
Answer or Reject an Incoming Call - No Call Currently in Progress
When you receive a call on your cellular phone, the UConnectsystem will interrupt the stereo audio and will ask if you would like to answer the call by pressing the Phonebutton. Press the Phonebutton to answer the call. To reject the call, press the Phonebutton until you hear a single beep indicating that the incoming call was rejected.
3
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Answer or Reject an Incoming Call - Call Currently in Progress
If a call is currently in progress and you have another incoming call, press the Phonebutton to place the current call on hold and answer the incoming call. To reject the incoming call, you can disregard the call and continue with your current conversation.
Making a Second Call while Current Call in Progress
To make a second call while you are currently in a call, press the Voice Recognitionbutton and say Dialor Callfollowed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress.
Putting a Call on Hold and Retrieving a Call from Hold
To put a call on hold, press the Phonebutton until you hear a single beep which will indicate that the call has been placed on hold. To bring the call back from hold, press the Phonebutton.
Toggling Between Two Calls
If two calls are in progress (one active and one on hold), press the Phonebutton until you hear a single beep indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time.
Conference Call
When two calls are in progress (one active and one on hold), press the Phonebutton until you hear a double beep indicating that the two calls have been joined into one conference call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75
Three-Way Calling
To initiate three-way calling, press the Voice Recogni­tionbutton while a call is in progress and make a second phone call. When the second call is established, press the Phonebutton until you hear a double beep indicating that the two calls have been joined into one conference call.
Call Termination
To end a call in progress, press the Phonebutton. All calls in progress will be terminated.
Phone Redial
Press the Phonebutton to begin.
After the Readyprompt, say Redial.
The UConnectsystem will call the last number that was dialed on your cellular phone. This may not be the last number dialed by your UConnectsystem.
Advanced Phone Connectivity
Transferring an Active Call between the UConnectSystem and Your Cellular Phone
The UConnectsystem allows ongoing calls to be trans­ferred to your cellular phone or to the UConnect system without terminating the call. To transfer an ongo­ing call from your cellular phone to the UConnect system or vice versa, press the Voice Recognitionbutton and say Transfer Call.
Delete Paired Cellular Phones
Press the Phonebutton to begin.
After the Readyprompt, say Setup.
When prompted, say Phone Pairing.
At the next prompt, say Delete.
3
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
You will be asked to say the name of the phone that you wish to delete. You can either say the name of the phone that you wish to delete or you can say Allto delete all the phones.
After the Readyprompt, say Setup List Phonesand the UConnectsystem will play the phone names of all paired cellular phones in order from highest prior­ity to lowest priority.
Connect or Disconnect the Connection between the UConnectSystem and Your Cellular Phone
Your cellular phone can be paired with many different electronic devices, but can only be actively connected with one electronic device at a time.
If you would like to connect or disconnect the Blue­toothconnection between a paired cellular phone and the UConnectsystem, follow the instruction described in your cellular phone users manual.
List Paired Cellular Phone Names
Press the Phonebutton to begin.
Select a Lower Priority Paired Cellular Phone
Press the Phonebutton to begin.
After the Readyprompt, say Setup.
When prompted, say Select Phone.
When prompted, say the phone name of the cellular phone you wish to use, or say List Phonesto hear a list of all the phones that have been paired to your UConnectsystem. To select a phone from the list, press the Voice Recognitionbutton and say Select.
The lower priority phone will only be used for the next phone call. After that, the UConnectsystem will return to using the highest priority phone in the vehicle.
UConnectSystem Features
Barge In - Touch Tone Phone Inputs
You can use your UConnectsystem to access a voice mail system, an automated service, or any other phone number that you can dial with any phone. When calling a number with your UConnectsystem that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the Voice Recogni­tionbutton and say the sequence you wish to enter followed by Send. For example, if required to enter your pin number, you can press the Voice Recognitionbutton and say 3746Send, or whatever you have made your pin. This method can also be used in instances where you are pressing a number on your keypad to navigate through a menu structure or to enter a number for a pager.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77
Barge In - Overriding Prompts
The Voice Recognitionbutton can be used when you wish to skip part of a prompt and issue your voice recognition command immediately. For example, if a prompt is playing Would you like to pair a phone, clear aѧ⬙, you could press the Voice Recognitionbutton and say Pair A Phoneto select that option without having to listen to the rest of the voice prompt.
Language Selection
To change the language that the UConnectsystem is using, press the Phonebutton and say the name of the language you wish to switch to (English, Español, or Français as equipped). After selecting one of the lan­guages, all prompts and voice commands will be in the selected language.
3
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Turning Confirmation Prompts On/Off
Turning confirmation prompts off will stop the system from confirming your choices (e.g. the UConnectsys­tem will not repeat a phone number before you dial it).
Press the Phonebutton to begin.
After the Readyprompt, say Setup Confirmation. The UConnectsystem will play the current confir­mation prompt status and you will be given the choice to change it.
Low Signal, Battery Strength, and Roam Notification
The UConnectsystem will provide notification to inform you if your cellular phone is in roaming status, has low signal strength, or has a low battery when you are trying to place a phone call.
Dialing Using the Cellular Phone Keypad
You can dial a phone number with your cellular phone keypad and still use the UConnectsystem. By dialing a number with your paired Bluetoothcellular phone, the audio will be played through your vehicles stereo sys­tem. The UConnectsystem will work the same as if you dialed the number using voice recognition.
Mute/Unmute
When you mute the UConnectsystem, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the UConnectsystem press the Voice Recognitionbutton and say Mute. In order to unmute the UConnectsystem; press the Voice Recognition button and say Unmute.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79
Help
If you need assistance at any prompt or if you want to know what your options are at any prompt, say Help. The UConnectsystem will play all the options at any prompt if you ask for help.
Cancel
At any prompt, you can say Canceland you will be returned to the previous menu.
Emergency Assistance
If you are in an emergency, say Dial Emergencyor Call Emergencyand the UConnectsystem will instruct your cellular phone to call 911.
Towing Assistance
If you need towing assistance, say Dial Towing Assis­tanceor Call Towing Assistance. Please refer to the 24-Hour Towing Assistance coverage details in the DaimlerChrysler Motors Company 24-Hour Towing As­sistance Program Guide.
SEATS
The seating options available in this truck are the result of extensive customer research and evaluations.
WARNING!
It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Be sure everyone in your vehicle is in a seat and using a seat belt properly.
3
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING!
Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
WARNING!
You can be seriously, even fatally injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. If you ride in this position, the shoulder harness will no longer be restraining you. In a collision you could slide under the seat belt and receive serious or fatal injuries. Recline in a seat only when the vehicle is parked.
40-20-40 Front Seat
As the name implies, the seat is divided into 3 segments. The outboard seat portions are each 40% of the total width of the seat. The back of the center portion (20%) easily folds down to provide an armrest/center storage compartment (if equipped).
Power Driver Seat
CAUTION!
Dont put anything under a power seat. It may cause damage to the seat controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81
Up, Down, Forward, and Rearward
3
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
The power seat controls are on the outboard side of the front seat cushions. Three switches control the seat move­ment. The four-way switch in the center can be moved forward or backwards to get the most comfortable posi­tion. The same switch can be moved up and down to control seat height. Change the seat angle by using the two toggle switches, tilting it up or down.
Tilt Adjustment
Manual Passenger Seat
Passenger Side Manual
The passenger seat is adjustable forward or backward and is equipped with a back recliner.
Manual Seatback Recline
The recliner mechanism control is on the outboard side of the seat. To recline, lean forward slightly, lift the lever, then push back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. Using body pressure, lean forward and rearward on the seat to be sure the seatback has latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83
3
Manual Recline Lever
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Adjustable Head Restraints
Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the restraints so that the upper edge is as high as practical, at least to the level of the ears.
To lower the head restraint, push in the button and then push down on the head restraint.
TO OPEN AND CLOSE THE HOOD
To open the hood, two latches must be released. First pull the hood release lever located below the steering wheel at the base of the instrument panel. Once the hood is released you must reach into the opening beneath the center of the grille and push up the latch to release the safety catch before raising the hood.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85
To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage.
WARNING!
If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving.
3
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
LIGHTS Interior Lights
Courtesy/ dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or if equipped, when the UNLOCK button is pressed on the key fob. Rotating the dimmer control to the optional fully upward position will
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87
turn on the cargo light located on the back of the cab. When a door is open and the interior lights are on, rotating the dimmer control all the way down to the OFF detent will cause all the interior lights to go out. This is also known as the Partymode because it allows the doors to stay open for extended periods of time without discharging the vehicles battery.
The brightness of the instrument panel lighting can be regulated by rotating the dimmer control up (brighter) or down (dimmer). When the headlights are ON you can supplement the brightness of the odometer, trip odom­eter, radio and overhead console by rotating the control up until you hear a click. This feature is termed the Parademode and is useful when headlights are re­quired during the day.
Battery Saver
To protect the life of your vehicles battery, Load Shed­ding is provided for both the interior and exterior lights.
If the ignition is off and any door is left ajar for 15 minutes or the dimmer control is rotated upwards for 15 minutes, the interior lights will automatically turn off.
If the headlamps remain on while the ignition is cycled off, the exterior lights will automatically turn off after 5 minutes. After 5 minutes timeout, if the headlamp switch is turned off and then turned on, the exterior lights will automatically turn off after 15 minutes.
If the dimmer control is rotated to the cargo lamp position with the ignition off, the cargo lamps will automatically turn off after 15 minutes.
NOTE: Battery Saver mode is cancelled if the ignition is ON.
3
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Headlamp Delay If Equipped
To aid in your exit, your vehicle, if equipped, can be programmed by your dealer with a headlamp delay that will leave the headlamps on for 0, 30, 60, or 90 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is on, and then the headlamp switch is cycled off. The headlamps will remain on for 60 seconds. Headlamp delay can be cancelled by either turning the headlamp switch ON then OFF or by turning the ignition ON.
Headlights, Parking Lights, Panel Lights
When the headlight switch is rotated to the first position, the parking lights, taillights, side marker
lights, license plate light and instrument panel lights are all turned on. The headlights will turn ON when the switch is rotated to the second position. The LAMP OUTindicator will be illuminated in the instru­ment cluster if a defective bulb or wiring circuit is detected for the headlamp system.
Your vehicle is equipped with plastic headlight lenses that are lighter and less susceptible to stone breakage than glass headlights.
Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89
To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol­lowed by rinsing.
Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses.
Daytime Running Lights (Canada and Fleet Vehicles Only)
The headlights on your vehicle will illuminate when the engine is started. This provides a constant Lights ON condition until the ignition is turned OFF. The lights illuminate at less than normal intensity. If the parking brake is applied the Daytime Running Lights will turn off.
Lights-on Reminder
If the headlights, parking lights, courtesy lights or cargo lights are left on, after the ignition is turned off, a continuous chime will sound when the drivers door is opened.
Fog Lights
The foglights are turned ON by placing the headlight rotary control in the parking light or headlight position and pulling out the headlight rotary control. The fog lights will operate only when the parking lights are ON or when the vehicle headlights are ON low beam. An indicator light located left of the switch will illuminate when the fog lights are on. The fog lights will turn off when the switch is pressed in, when the headlight switch is rotated to the OFF position or the high beam is selected.
3
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CARGO LIGHT
The cargo lights are turned on by rotating the dimmer control to the optional fully upward position. The cargo lights will also turn on for 30 seconds when a key fob Unlock is pressed, as part of the illuminated entry feature.
MULTIFUNCTION CONTROL LEVER
The multifunction control lever is located on the left side of the steering column.
Turn Signals
Move the lever up or down to signal a right-hand or left-hand turn.
The arrow on either side of the instrument cluster flashes to indicate the direction of the turn, and proper operation of the front and rear turn signal lights. If a defective bulb or wiring circuit is detected for the turn signal system, the arrow indicators will flash at a faster rate. Also, the LAMP OUTindicator in the instrument cluster will be
illuminated and a chime will be heard. If an indicator fails to light when the lever is moved, it would suggest that the switch or indicator lamp is defective.
You can signal a lane change by moving the lever partially up or down.
Passing Light
You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer­ing wheel. This will cause the high beam headlights to turn on until the lever is released.
High Beam / Low Beam Select Switch
Pull the multifunction control lever fully toward the steering wheel to switch the headlights from HIGH or LOW beam.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91
3
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Windshield Wipers
The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed.
Intermittent Wiper System
The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93
The delay interval decreases as you rotate the knob until it enters the LO continual speed position. The delay can be regulated from a maximum of about 15 seconds between cycles, to a cycle every 2 seconds. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km) or less.
WARNING!
Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind­shield washer use.
Windshield Washers
To use the washer, push in on the washer knob on the end of the multifunction control lever and hold while spray is desired. If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released. It will then resume the intermittent interval previously selected. If the washer knob is pushed, for a period greater than 1 second, while in the OFF position, the wiper will wipe approximately three wipes, after the wash knob is released.
To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers.
3
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
TILT STEERING COLUMN
To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Push the lever back up to lock the column firmly in place.
WARNING!
Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col­umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve­hicle is stopped. Be sure it is locked before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95
DRIVER ADJUSTABLE PEDALS
The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals.
Adjustment
1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel.
2. Fasten and adjust the seatbelts.
3. Move the adjustable pedal switch, located to the left of the steering column near the parking brake release, in the direction you desire to move the pedals.
4. The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control is SET.
3
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CAUTION!
Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedals path.
ELECTRONIC SPEED CONTROL
When engaged, this device takes over accelerator opera­tion at speeds greater than 35 mph (56 km/h). The controls are mounted on the steering wheel.
To Activate
Push the ON/OFF button to the ON position. In the instrument cluster, the word CRUISEilluminates when the system is on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97
To Set At A Desired Speed
When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed.
To Deactivate
A soft tap on the brake pedal, normal braking, clutch pressure while slowing the vehicle, or pressing the CAN­CEL button will deactivate speed control without erasing the memory. Pushing the ON/OFF button to the OFF position or turning off the ignition erases the memory.
WARNING!
Leaving the Speed Control ON when not in use is dangerous. You could accidentally set the system to cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you arent using it.
To Resume Speed
To resume a previously set speed, push and release the RESUME button. Resume can be used at any speed above 30 mph (50 km/h).
To Vary The Speed Setting
When the speed control is on, speed can be increased by pressing and holding the ACCEL button. When the button is released, a new set speed will be established.
Tapping the ACCEL button once will result in a speed increase of 2 mph (3 km/h). Each time the button is tapped, speed increases so that tapping the button three times will increase speed by three increments.
Tapping the COAST button once will result in a speed decrease of 1 mph (2 km/h). Each time the button is tapped, speed will decrease. For example, tapping the button 3 times will decrease the speed by 3 mph (6 km/h).
3
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
To decrease speed while the speed control is on, press and hold the COAST button. Release the button when the desired speed is reached, and the new speed will be set.
To Accelerate For Passing
Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed.
NOTE: When driving uphill, at elevations above 2,000 feet (610 meters), or when the vehicle is heavily loaded the vehicle may slow below the SET speed. If the vehicle speed drops below (refer to the table below for the speed for your specific engine), the speed control will automati­cally disengage. If this happens, you can push down on the accelerator pedal to maintain the desired speed.
Vehicles equipped with a 6–speed-manual transmission should be operated in 5th gear or lower under the above conditions.
WARNING!
Speed Control can be dangerous where the system cant maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Dont use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99
OVERHEAD CONSOLE
The overhead console consists of the following features:
Courtesy/Reading Lights
Compass/Temperature Mini-Trip Computer (CMTC)
Universal Garage Door Opener
Courtesy/Reading Lights
In the middle of the console are two courtesy/reading lights.
Both lights illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (fully upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry transmitter, if so equipped. These lights are also operated individually as reading lights by pressing the recessed area of the corresponding lens.
NOTE: The courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the interior lights are left on after the vehicle is turned off, they will extinguish after 15 minutes.
3
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
COMPASS/TEMPERATURE MINI-TRIP COMPUTER
This overhead console consists of the following:
Courtesy Lights
Compass/Temperature Mini-Trip Computer
Universal Garage Door Opener
This overhead console allows you to choose between a compass/temperature display and one of four trip con­ditions being monitored.
US/M Button
Use this button to change the display from U.S. to metric measurement units.
Loading...