Dodge 2013 Grand Caravan User Manual

Download

Page 1

grand Caravan

USER GUIDE

2013

Page 2

If you are the first registered retail owner of your vehicle, you may obtain a complimentary printed copy of the Owner’s Manual, Navigation/ Uconnect

Manuals or Warranty Booklet by calling 1-800-423-6343 (U.S.) or 1-800-387-1143 (Canada) or by contacting your dealer.

This User Guide is intended to familiarize you with the important features of your vehicle. The DVD

enclosed contains your Owner’s Manual, Navigation/Uconnect

Manuals, Warranty Booklets, Tire Warranty and Roadside Assistance (new vehicles purchased in the U.S.) or Roadside Assistance (new vehicles purchased in Canada) in electronic format. We hope you ﬁnd it useful. Replacement

IMPORTANT

The driver’s primary responsibility is the safe operation of the vehicle. Driving while distracted can result in loss of vehicle control, resulting in a collision and personal injury. Chrysler Group LLC strongly recommends that the driver use extreme caution when using any device or feature that may take their attention off the road. Use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous and could lead to a serious collision. Texting while driving is also dangerous and should never be done while the vehicle is moving. If you ﬁnd yourself unable to devote your full attention to vehicle operation, pull off the road to a safe location and stop your vehicle. Some States or Provinces prohibit the use of cellular telephones or texting while driving. It is always the driver’s responsibility to comply with all local laws.

dodge.com

This guide has been prepared to help you get quickly acquainted with your new Dodge and to provide a convenient reference source for common questions. However, it is not a substitute for your Owner’s Manual.

For complete operational instructions, maintenance procedures and important safety messages, please consult your Owner’s Manual, Navigation/Uconnect

Not all features shown in this guide may apply to your vehicle. For additional information on accessories to help personalize your vehicle, visit www.mopar.com or your local Dodge dealer.

Page 3

TABLE OF CONTENTS

INTRODUCTION/WELCOME

WELCOME FROM CHRYSLER GROUP LLC . . . 2

CONTROLS AT A GLANCE

DRIVER COCKPIT ................4

INSTRUMENT CLUSTER .............6

GETTING STARTED

KEYFOB .....................8

REMOTE START .................9

THEFT ALARM ..................9

SEATBELT ...................10

SUPPLEMENTAL RESTRAINT SYSTEM

(SRS)—AIRBAGS................10

CHILD RESTRAINTS ..............11

FRONT SEATS .................14

REARSEATS ..................15

HEATEDSEATS .................19

HEATED STEERING WHEEL ..........20

TILT/TELESCOPING STEERING COLUMN . . . 20

ADJUSTABLE PEDALS .............21

OPERATING YOUR VEHICLE

ENGINE BREAK-IN RECOMMENDATIONS . . . 22 TURN SIGNAL/WIPER/WASHER/HIGH

BEAM LEVER ..................22

HEADLIGHT SWITCH AND HALO LIGHT

SWITCH .....................24

SPEED CONTROL ................25

ELECTRONIC RANGE SELECTION (ERS) . . . 26

FUEL ECONOMY (ECON) MODE ........26

MANUAL CLIMATE CONTROLS ........27

THREE ZONE MANUAL CLIMATE CONTROLS . . 28 THREE ZONE AUTOMATIC TEMPERATURE

CONTROLS (ATC) ................29

PARKSENSE® REAR PARK ASSIST ......30

PARKVIEW® REAR BACK-UP CAMERA ....30

BLIND SPOT MONITORING WITH REAR

CROSS PATH ..................31

POWER SLIDING SIDE DOORS .........31

POWER LIFTGATE ...............32

POWER SUNROOF ...............32

WIND BUFFETING ...............33

ELECTRONICS

YOUR VEHICLE'S SOUND SYSTEM ......34

Uconnect® 130 .................36

Uconnect® 130 WITH SiriusXM SATELLITE

RADIO......................38

Uconnect® 430/430N .............41

Uconnect® 730N ................50

SiriusXM SATELLITE RADIO/TRAVEL LINK . . 60

STEERING WHEEL AUDIO CONTROLS ....63

iPod®/USB/MP3 CONTROL ..........63

Uconnect® Phone ...............64

Uconnect® VOICE COMMAND .........67

Bluetooth® STREAMING AUDIO ........69

VIDEO ENTERTAINMENT SYSTEM (VES™) ELECTRONIC VEHICLE INFORMATION

CENTER (EVIC) .................71

PROGRAMMABLE FEATURES .........72

UNIVERSAL GARAGE DOOR OPENER

(HomeLink®) ..................73

POWER INVERTER ...............75

POWER OUTLETS ...............76

..69

UTILITY

IN-FLOORSTORAGE–STOW'NGO® ......78

ROOF LUGGAGE RACK .............78

TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS) . . . 79

RECREATIONAL TOWING

(BEHIND MOTORHOME, ETC.) .........79

WHAT TO DO IN EMERGENCIES

ROADSIDE ASSISTANCE ............80

INSTRUMENT CLUSTER WARNING LIGHTS . . . 80

IF YOUR ENGINE OVERHEATS .........84

JACKING AND TIRE CHANGING ........85

JUMP-STARTING ...............95

SHIFT LEVER OVERRIDE ............97

TOWING A DISABLED VEHICLE ........97

FREEING A STUCK VEHICLE .........98

EVENT DATA RECORDER (EDR) ........99

MAINTAINING YOUR VEHICLE

OPENING THE HOOD .............100

ADDING FUEL .................101

ENGINE COMPARTMENT ...........102

FLUIDS AND CAPACITIES ..........103

MAINTENANCE SCHEDULE .........104

MAINTENANCE RECORD ...........108

FUSES .....................109

TIRE PRESSURES ...............112

WHEEL AND WHEEL TRIM CARE .......113

EXTERIOR BULBS ...............113

CONSUMER ASSISTANCE

CHRYSLER GROUP LLC

CUSTOMER CENTER .............114

CHRYSLER CANADA INC.

CUSTOMER CENTER .............114

PUBLICATIONS ORDERING ..........114

ASSISTANCE FOR THE HEARING IMPAIRED REPORTING SAFETY DEFECTS IN THE

UNITEDSTATES ................115

. . 114

MOPAR ACCESSORIES

AUTHENTIC ACCESSORIES BY MOPAR® . . . 116

INDEX

.....................117

FAQ (How To?)

FREQUENTLY ASKED QUESTIONS ......120

Page 4

INTRODUCTION/WELCOME

WELCOME FROM CHRYSLER GROUP LLC

Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.

Your new Chrysler Group LLC vehicle has characteristics to enhance the driver's control under some driving conditions. These are to assist the driver and are never a substitute for attentive driving. They can never take the driver's place. Always drive carefully.

Your new vehicle has many features for the comfort and convenience of you and your passengers. Some of these should not be used when driving because they take your eyes from the road or your attention from driving. Never text while driving or take your eyes more than momentarily off the road.

This guide illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This guide may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this guide that are not available on this vehicle. Chrysler Group LLC reserves the right to make changes in design and specifications and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured.

This User Guide has been prepared to help you quickly become acquainted with the important features of your vehicle. It contains most things you will need to operate and maintain the vehicle, including emergency information.

The DVD includes a computer application containing detailed owner's information which can be viewed on a personal computer or MAC computer.The multimedia DVD also includes videos which can be played on any standard DVD player (including the Uconnect® TouchScreen Radios). Additional DVD operational information is located on the back of the DVD sleeve.

For complete owner information, refer to your Owner's Manual on the DVD in the owner’s kit provided at the time of new vehicle purchase. For your convenience, the information

contained on the DVD may also be printed and saved for future reference.

Chrysler Group LLC is committed to protecting our environment and natural resources. By converting from paper to electronic delivery for the majority of the user information for your vehicle, together we greatly reduce the demand fortree-based products and lessen the stress on our environment.

Page 5

INTRODUCTION/WELCOME

VEHICLES SOLD IN CANADA

With respect to any vehicles sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution.

WARNING!

• Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury.

• Always make sure that objects cannot fall into the driver foot well while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control.

• Failure to properly follow floor mat installation or mounting can cause interference with the brake pedal and accelerator pedal operation causing loss of control of the vehicle.

• Never use the ‘PARK’ position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.

• Refer to your Owner's Manual on the DVD for further details.

USE OF AFTERMARKET PRODUCTS (ELECTRONICS)

The use of aftermarket devices including cell phones, MP3 players, GPS systems, or chargers may affect the performance of on-board wireless features including Keyless Enter-N-Go™ and Remote Start range. If you are experiencing difficulties with any of your wireless features, tr y disconnecting your aftermarket devices to see if the situation improves. If your symptoms persist, please see an authorized dealer.

CHRYSLER, DODGE, JEEP, RAM TRUCK, SRT, ATF+4, MOPAR and Uconnect are registered trademarks of Chrysler Group LLC.

Page 6

CONTROLS AT A GLANCE

DRIVER COCKPIT

Page 7

L. Hood Release pg. 100

M. Parking Brake Release

N. Power Mirrors

O. Power Windows

P. Power Door Locks

CONTROLS AT A GLANCE

Q. Power Vent Windows

R. Instrument Panel Dimmer pg. 24

H. Climate Controls pg. 27

A. Headlight Switch pg. 24

• Fuel Economy (ECON) mode pg. 26

I. SWITCH PANEL

Lever (behind steering wheel) pg. 22

B. Turn Signal/Wiper/Washer/High Beams

• Hazard Switch

(EVIC) Controls pg. 71

C. Electronic Vehicle Information Center

• Power Inverter pg. 75

D. Electronic Vehicle Information Center

pg. 82

• Electronic Stability Control (ESC) OFF

(EVIC) Display

E. Instrument Cluster pg. 6

pg. 76

J. Power Outlets (inside console storage)

F. Transmission Gear Selector

G. Audio System (touch-screen-radio

K. Speed Control pg. 25

shown) pg. 34

Page 8

CONTROLS AT A GLANCE

INSTRUMENT CLUSTER

Warning Lights

- Low Fuel Warning Light

- Charging System Light

- Oil Pressure Warning Light**

- Anti-Lock Brake (ABS) Light**

- Air Bag Warning Light**

- Electronic Throttle Control (ETC) Light

- Tire Pressure Monitoring System (TPMS) Light

- Engine Temperature Warning Light

- Seat Belt Reminder Light

BRAKE

(See page 80 for more information.)

- Brake Warning Light**

- Malfunction Indicator Light (MIL)**

- Electronic Stability Control (ESC) Activation/Malfunction Indicator Light*

Page 9

CONTROLS AT A GLANCE

Indicators

- Turn Signal Indicators

- High Beam Indicator

- Front Fog Light Indicator

- Vehicle Security Indicator*

- Electronic Stability Control (ESC) Off Indicator*

Odometer Messages

door - Door Ajar noFUSE* - Fuse Fault gATE* - Liftgate Ajar CHAngE OIL* - Change Engine Oil gASCAP - Fuel Cap Fault LoCOOL - Low Coolant LoW tirE* - Low Tire Pressure

* If equipped ** Bulb Check with Key On

- Electronic Speed Control ON Indicator

- Electronic Speed Control Set Indicator

Page 10

GETTING STARTED

KEY FOB

Locking And Unlocking The Doors/Liftgate

• Press the LOCK button once to lock all the doors and the liftgate. Press the UNLOCK button once to unlock the driver’s door only and twice within five seconds to unlock all the doors and liftgate.

• All doors can be programmed to unlock on the first press of the UNLOCK button. Refer to Programmable Features in the Electronics section of this guide.

Panic Alarm

• Press the PANIC button once to turn the panic alarm on.

• Wait approximately three seconds and press the button a second time to turn the panic alarm off.

Power Liftgate

• ress the LIFTGATE button twice within five seconds to power open/close the Power Liftgate. If the button is pressed twice again while the liftgate is being power closed, the liftgate will reverse to the full open position.

Power Sliding Doors

• Press the LEFT or RIGHT Power Sliding Door button twice within five seconds to power open/close the Power Sliding Door. If the button is pressed twice again while the door is being power closed, the door will reverse to the full open position.

Emergency Key

• Should the battery in the vehicle or the Key Fob transmitter go dead, there is an emergency key located in the Key Fob that can be used for locking and unlocking the doors. To remove the emergency key, slide the button at the top of the Key Fob sideways with your thumb and then pull the key out with your other hand.

Page 11

GETTING STARTED

WARNING!

• Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be severely injured or killed. Children should be warned not to touch the parking brake, brake pedal, or the shift lever. Do not leave the KeyFob inside the vehicle, or in a location accessible to children. A child could start the vehicle, operate power windows, other controls, or move the vehicle.

• Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause them to be severely injured or killed.

• Keep Key Fob transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death.

REMOTE START

• Press the REMOTE START button the REMOTE START button a third time shuts the engine off.

on the Key Fob twice within five seconds. Pressing

• To drive the vehicle, press the UNLOCK button, insert the Key Fob in the ignition and turn to the ON/RUN position.

• With remote start, the engine will only run for 15 minutes (timeout) unless the ignition Key Fob is placed in the ON/RUN position.

• The vehicle must be started with the Key Fob after two consecutive timeouts.

WARNING!

• Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause you or others to be severely injured or killed when inhaled.

• Keep Key Fob transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause you and others to be severely injured or killed.

THEFT ALARM

To Arm:

• Press the Key Fob LOCK button or the power door lock switch while the door is open.

To Disarm:

• Press the Key Fob UNLOCK button or turn the ignition to the ON/RUN position.

Page 12

GETTING STARTED

SEAT BELT

• Be sure everyone in your vehicle is in a seat and using a seat belt properly.

• Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.

• Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt.

• A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together.

• A belt that is too loose will not protect you properly. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.

• A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically,checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).

• The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision.

• A deployed pretensioner or a deployed air bag must be replaced immediately.

WARNING!

In a collision, you and your passengers can suffer much greater injuries if you are not buckled up properly.You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly.

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) — AIR BAGS

• This vehicle has Advanced Front Air Bags for both the driver and right front passenger as a supplement to the seat belt restraint system. The Advanced Front Air Bags will not deploy in every type of collision.

• AdvancedFront Air Bags are designed to provide additional protection by supplementing the seat belts in certain frontal collisions depending on several factors, including the severity and type of collision. Advanced Front Air Bags are not expected to reduce the risk of injury in rear, side, or rollover collisions.

• This vehicle is equipped with Supplemental Side Air Bag Inflatable Curtains to protect the driver, front and rear passengers sitting next to a window.

Page 13

GETTING STARTED

• This vehicle is equipped with Supplemental Seat-Mounted Side Air Bags to provide enhanced protection to help protect an occupant during a side impact.

• This vehicle is equipped with a Supplemental Driver Side Knee Air Bag to provide enhanced protection and work together with the Driver Advanced Front Air Bag during a frontal impact.

• If the Air Bag Warning Light driving, have the vehicle serviced by an authorized service center immediately.

• Refer to the Owner's Manual on the DVD for further details regarding the Supplemental Restraint System (SRS).

is not on during starting, stays on, or turns on while

WARNING!

• Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won't deploy at all. Always wear your seat belts even though you have air bags.

• Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel.

• Supplemental Side Air Bag Inflatable Curtains and Supplemental Seat-MountedSide Air Bags need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat.

• Being too close to the Supplemental Side Air Bag Inflatable Curtain and/or SeatMounted Side Air Bag during deployment could cause you to be severely injured or killed.

• Do not drive your vehicle after the air bags have deployed. If you are involved in another collision, the air bags will not be in place to protect you.

• After any collision, the vehicle should be taken to an authorized dealer immediately.

CHILD RESTRAINTS

• Children 12 years and under should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.

• Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.

NOTE:

• For additional information, refer to www.seatcheck.org or call 1–866–SEAT-CHECK (1–866–732–8243).

• Canadian residents, should refer to Transport Canada’s website for additional information http://www.tc.gc.ca/eng/roadsafety/safedrivers-childsafety-index-53.htm.

Page 14

GETTING STARTED

Installing The LATCH - Compatible Child Restraint System

Each vehicle, exceptcommercial cargo vehicles, is equipped with the child restraint anchor-

• age system called LATCH, which stands for Lower Anchors and Tether for CHildren.

• Two LATCH child restraint anchorage systems are installed on all second-row seats and in the center position on all third row fold-in-floor seats.

• Second-row seats also feature tether strap anchorages, located in the rear surface of the seatback.

• In addition, all third row fold-in-floor seats are equipped with a child restraint tether anchor at the center seating position.

Installing The Lower Attachments:

• The vehicle lower anchorages are round bars located at the rear of the seat cushion where it meets the seatback.

• Loosen the child seat adjusters on the lower child restraint attachment straps to ease the installation.

NOTE:

It is recommended to loosen the top tether strap and route it loosely prior to securing the lower anchors so the top tether strap is not trapped between the vehicle seat and child restraint.

• Attach the lower child restraint attachment straps to the vehicle’s lower anchor bars. Ensure that the lower attachment strap is firmly engaged and that the hook is secure.

• Tighten the lower attachment strap while firmly pushing the child restraint rearward and downward into the vehicle seat. Remove all slack in the lower attachment straps.

Installing The Top Tether Strap ( With Either Lower Anchors Or Vehicle Seat Belt):

• Route the top tether strap under the adjustable head restraint between the steel posts.

• Provide enough slack for the tether strap to reach the tether anchor located near the bottom of the seat back.

• Clip tether hook to tether anchor. Ensure that the hook is firmly engaged and secure.

• Remove all slack and tighten tether strap according to child restraint manufacturer’s instructions.

NOTE:

The top tether strap is always to be secured, regardless of if the child restraint is installed with the lower anchors or the vehicle seat belt.

Page 15

GETTING STARTED

Installing The Child Restraint Using The Vehicle Seat Belts

• To install a child restraint, first, pull enough of the seat belt webbing from the retractor to route it through the belt path of the child restraint and slide the latch plate into the buckle.

• Next, extract all the seat belt webbing out of the retractor and then allow the belt to retract into the retractor. Finally, pull on any excess webbing to tighten the lap portion around the child restraint. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary.

• Once you have completed securing the child restraint with the seat belt, secure the top tether strap.

WARNING!

• In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be severely injured or killed. Any child riding in your vehicle should be in a proper restraint for the child's size.

• Failure to comply with the following conditions could result in you and others being severely injured or killed:

• Be certain that the seat cushion is locked securely into position before using

the seat. An improperly latched seat cushion could cause passengers to be severely injured or killed.

• An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.

• Rearward-facing child seats must never be used in the front seat of a vehicle with a front passenger air bag. An air bag deployment could cause severe injury or death to infants in this position.

Page 16

GETTING STARTED

FRONT SEATS

Power Seat

• The power seat switch controls forward/ back, up/down, and tilt adjustment.

• The recline switch, located on the outboard side of the seat, controls seatback adjustment.

Power Lumbar

• Push the switch forward to increase the lumbar support.Push the switch rearward to decrease the lumbar support.

Manual Seat Adjustment

Forward/Rearward

• Lift up on the adjusting bar located at the front of the seat near the floor and release it when the seat is at the desired position. Then, using body pressure, move forward and backward on the seat to be sure that the seat adjusters have latched.

Recliner

• Lift the recliner lever located on the outboard side of the seat, lean back and release at the desired position.

Memory Seat

The memory seat feature allows you to

• save two different driver seating positions, driver's outside mirror, adjustable brake and accelerator pedals, and radio station preset settings. The memory seat buttons are located on the driver's door panel.

• Adjust all memory profile settings, press the SET button then press 1 or 2 within five seconds.

• To program a Key Fob to the memory position, press and release the LOCK button within 10 seconds on the Key Fob to be programmed.

Page 17

GETTING STARTED

• Place the ignition switch in the ON position, select Remote Linked to Memory in the Electronic Vehicle Information Center (EVIC) and enter Yes.

• Press 1 or 2 to recall the saved positions, or press UNLOCK on the programmed Key Fob.

CAUTION!

Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.

WARNING!

• Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted, and you could be severely injured or killed. Only adjust a seat while the vehicle is parked.

• Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision, you could slide under the seat belt and be severely injured or killed. Use the recliner only when the vehicle is parked.

REAR SEATS

Second Row Seats – Stow 'n Go®

On vehicles equipped with Stow 'n Go®

• seats, the seats will fold and tumble in one motion.

• Move the front seat fully forward.

• Recline the front seatback fully forward. Raise the armrests on the second row seat.

•

NOTE:

Seat will not stow in the storage bin unless the armrests are raised.

Page 18

GETTING STARTED

• Slide the storage bin locking mechanism to the “LOCK” position and then pull up on the storage bin latch to open the cover.

• Pull upward on the seatback recliner lever located on the outboard side of the seat.

• The non-adjustable head restraint and seatback will fold automatically during the seat tumble.

• The seat will automatically tumble into position for easy storage.

• Push the seat into the storage bin and close the storage bin cover.

To Unstow Second Row Seats

• Pull up on the storage bin latch to open the cover.

• Pull up on the strap to lift the seat out of the storage bin and push the seat rearward to latch the seat anchors.

• Lift the seatback to the full upright position.

• Return the head restraint to its upright position, close the storage bin cover and slide the storage bin locking mechanism to the “Unlocked” position.

Page 19

GETTING STARTED

Third Row Seats

Third Row Power Recliner

• The power recline feature, located on the side of the seat cushion, adjusts the seatback angle forward/rearward for occupant comfort.

Third Row Power Seat Switch

NOTE:

• Disconnect the center shoulder belt from the small buckle and lower the head restraints before attempting to fold/stow the power third row seats.

• A one-touch power folding seat switch is located in the left rear trim panel as part of a switch bank.

• Left and right third row seats can be folded individually or together. The third row power folding seats adjust to multiple positions.

• The switch is only functional when the liftgate is open and the vehicle is in PARK.

• To abort seat operation while the seat is in motion, press a different seat position selector switch to stop the seat. Once the seat stops moving, then the desired position can be selected.

• The third row power seat system includes obstacle detection for safe operation. When the system detects an obstacle, the motors will stop and reverse the motion a short distance to move the seat away from the obstacle. Should this occur, remove the obstacle and press the button again for the desired position.

• Refer to your Owner's Manual on the DVD for manual third row seat folding instructions.

Page 20

GETTING STARTED

Manually Folding Third Row Seats

• Lower the center head restraint down to the seatback by pushing the button on the guide and pushing the head restraint down.

• Lower the outboard head restraints by pulling on the release strap marked “1” located on the outboard side of the head restraint.

• Pull release strap marked “2” located on the rear of the seat to lower the seatback.

• Pull release strap marked “3” to release the anchors.

• Pull release strap marked “4” and tumble the seat rearward into the storage bin.

To Unfold Third Row Seats

• Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the anchors latch.

• Pull release strap marked “2” to unlock the recliner.

• Pulling strap “4” releases the seatback to return to its full upright position.

• Raise the head restraint to its upright position.

Page 21

GETTING STARTED

CAUTION!

The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.

WARNING!

• In a collision, serious injury could result if the seat storage bin covers are not properly latched.

• Do not drive the vehicle with the storage bin covers open.

• Keep the storage bin covers closed and latched while the vehicle is in motion.

• Do not use a storage bin latch as a tie down.

• In a collision, you or others in the vehicle could be injured if the seats are not properly latched to their floor attachments. Always be sure the seats are fully latched.

HEATED SEATS

Front Heated Seats

The controls for front heated seats are lo-

• cated on the center instrument panel area.

• Press the switch once to select High-level heating. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off.

• If the High-level setting is selected, the system will automatically switch to Lowlevel after approximately 30 minutes. The Low-level setting will turn Off automatically after approximately 45 minutes.

Second Row Heated Seats

•

Second row heated seat switches are located in the sliding door handle trim panels.

• Press the switch once to select High-level heating. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off.

Page 22

GETTING STARTED

WARNING!

• Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical conditions must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time.

• Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.

HEATED STEERING WHEEL

•

The steering wheel contains a heating element that heats the steering wheel to one temperature setting.

• The heated steering wheel switch is located on the center instrument panel.

• Press the switch once to turn the heating element On. Press the switch a second time to turn the heating element Off.

Once the heated steering wheel has been

• turned on, it will operate for approximately 58 to 70 minutes before automatically shutting off. The heated steering wheel can shut off early or may not turn on when the steering wheel is already warm.

TILT/TELESCOPING STEERING COLUMN

• The tilt steering column tilt lever is located below the steering wheel.

• Push down on the tilt lever to unlock the steering column.

• With one hand firmly on the steering wheel, move the steering column upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.

• Pull upward on the tilt lever to lock the column firmly in place.

Page 23

GETTING STARTED

WARNING!

Do not adjust the steering wheel while driving. The tilt adjustment must be locked while driving. Adjusting the steering wheel while driving or driving without the tilt adjustment locked could cause the driver to lose control of the vehicle. Failure to follow this warning may result in you and others being severely injured or killed.

ADJUSTABLE PEDALS

• Press the switch located on the left side of the steering column forward to move the brake and accelerator pedals away from the driver and press the switch rearward to move the pedals closer to the driver.

NOTE:

The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control is set.

CAUTION!

Do not place any article under the adjustable pedals or impede its ability to move, as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal's path.

WARNING!

Do not adjust the pedals while the vehicle is moving. You could lose control and have a collision. Always adjust the pedals while the vehicle is parked.

Page 24

OPERATING YOUR VEHICLE

ENGINE BREAK-IN RECOMMENDATIONS

•

A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle.

• Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.

• While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Wide-open throttle acceleration in low gear can be detrimental and should be avoided.

• The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades, refer to “Maintaining Your Vehicle”.

NOTE:

A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-inand not interpreted as an indication to an engine problem or malfunction.

CAUTION!

Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.

TURN SIGNAL/WIPER/WASHER/HIGH BEAM LEVER

Turn Signal/Lane Change Assist

• Tap the lever up or down once and the turn signal (right or left) will flash three times and automatically turn off.

• Vehicles equipped with Blind Spot Monitoring will produce a visual alert and may be programmed to produce an audible alert when signaling a lane change; refer to your Owner’s Manual on the DVD for operation.

Page 25

OPERATING YOUR VEHICLE

Front Wipers

Intermittent, Low And High Operation

• Rotate the end of the lever to the first detent position for one of five intermittent settings, the second detent for low wiper operation and the third detent for high wiper operation.

Rain Sensing Wipers

• This feature senses moisture on the vehicle’s windshield and automatically activates the wipers for the driver when the switch is in the intermittent positions. Refer to Programmable Features in Electronics for further details.

Mist

• Push the end of the lever inward to the first detent when a single wipe is desired.

NOTE:

The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be activated in order to spray the windshield with washer fluid.

Washer Operation

• Push the end of the lever inward to the second detent and hold for as long as spray is desired.

Rear Wiper

• Rotate the center portion of the lever forward to the first detent for rear wiper operation.

Rear Washer

• Rotate the center portion of the lever past the first detent to activate the rear washer.

High Beams

• Push the lever away from you to activate the high beams.

• A high beam symbol will illuminate in the cluster to indicate the high beams are on.

NOTE:

For safe driving, turn off the high beams when oncoming traffic is present to prevent headlight glare and as a courtesy to other motorists.

Flash To Pass

• Pull the lever toward you to activate the high beams. The high beams will remain on until the lever is released.

Page 26

OPERATING YOUR VEHICLE

HEADLIGHT SWITCH AND HALO LIGHT SWITCH

Automatic Headlights/Parking Lights/Headlights

• Rotate the headlight switch, located on the instrument panel to the left of the steering wheel, to the first detent for parking lights for headlights

• With the parking lights or low beam headlights on, push the headlight switch once for fog lights.

• Rotate the headlight switch to “AUTO” for AUTO headlights.

• When set to AUTO, the system automatically turns the headlights on or off based on ambient light levels.

and to the second detent

SmartBeams™

• The SmartBeam™ system provides increased forward lighting at night by automating high beam control through the use of a digital camera mounted on the inside rearview mirror. This camera detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view.

Instrument Panel Dimmer

• Rotate the dimmer control to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened.

• Rotate the dimmer control up to increase the brightness of the instrument panel when the parking lights or headlights are on.

• Rotate the dimmer control up to the next detent position to fully brighten the odometer and radio when the parking lights or headlights are on. Refer to your Uconnect®/Radio User Manual on the DVD for display dimming.

• Rotate the dimmer control up to the last detent position to turn on the interior lighting.

Overhead (Halo) Light

• To activate the Halo lights, rotate the Halo switch control upward or downwardto increase or decrease the lighting.

Page 27

OPERATING YOUR VEHICLE

SPEED CONTROL

• The Speed Control switches are located on the steering wheel.

Cruise ON/OFF

• Push the ON/OFF button to activate the Speed Control.

• CRUISE cluster to indicate the Speed Control is on.

• Push the ON/OFF button a second time to turn the system off.

SET

• With the Speed Control on, push and release the SET – button to set a desired speed.

Accel/Decel

• Once a speed is set, pushing the RES + button once or the SET – button once will increase or decrease the set speed approximately 1 mph (2 km/h).

• Push and hold the RES + button to accelerate in 5 mph (8 km/h) increments or push and hold the SET – button to decelerate in 5 mph (8 km/h) increments; release the button to save the new set speed.

Resume

To resume a previously selected set speed in memory, push the RES + button and release.

•

Cancel

• Push the CANCEL button, or apply the brakes to cancel the set speed and maintain the set speed memory.

will appear on the instrument

• Push the ON/OFF button to turn the system off and erase the set speed memory.

Leaving the Electronic Speed Control system on when not in use is dangerous. You

• could accidentally set the system or cause it to go faster than you want. You could

lose control and have a collision. Always leave the Electronic Speed Control system off when you are not using it.

• Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. A collision could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.

WARNING!

Page 28

OPERATING YOUR VEHICLE

ELECTRONIC RANGE SELECTION (ERS)

• Electronic Range Select (ERS) allows you to limit the highest available transmission gear,and can be activated during any driving condition. When towing a trailer or operating the vehicle in off-road conditions, using ERS shift control will help you maximize both performance and engine braking.

• To shift from DRIVE mode to ERS mode, move the shift lever to the left (-) once. The current gear will be maintained as the top gear.To disable ERS, simply press and hold the shift lever to the right (+) until “D” is displayed in the instrument cluster odometer.

• Switching between ERS and DRIVE mode can be done at any vehicle speed.

• Refer to your Owner's Manual on the DVD for further details.

FUEL ECONOMY (ECON) MODE

• The Fuel Economy (ECON) mode can improve the vehicle’s overall fuel economy during normal driving conditions.

• Press the “econ” switch in the center stack of the instrument panel and a green light will indicate the ECON mode is engaged.

Page 29

OPERATING YOUR VEHICLE

• When the Fuel Economy (ECON) Mode is engaged, the vehicle control systems will be able to change the following:

• The transmission will upshift sooner and downshift later.

• The transmission will skip select gears during shifts to allow the engine to operate at lower speeds.

• The torque converter clutch will engage sooner (lower engine rpm’s) and remain on longer.

• The engine idle speed will be lower.

• The overall driving performance will be more conservative.

MANUAL CLIMATE CONTROLS

Air Recirculation

• Use Recirculation for maximum A/C operation.

• For window defogging, turn the recirculation button off.

• Recirculation is allowed in floor mode.

• Recirculation is allowed in defrost/floor (mix modes) for approximately five minutes.

Heated Mirrors

• The mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster.

Rear Window Defroster

• Pressing the rear window defroster button will turn on the defroster for approximately 10 minutes. An indicator in the button will illuminate when the rear window defroster is on. For an additional 10 minutes of operation, press the button a second time.

Page 30

OPERATING YOUR VEHICLE

THREE ZONE MANUAL CLIMATE CONTROLS

Air Recirculation

• Use Recirculation for maximum A/C operation.

• For window defogging, turn the recirculation button off.

• Recirculation is allowed in floor mode.

• Recirculation is allowed in defrost/floor (mix modes) for approximately five minutes.

Heated Mirrors

• The mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster.

Rear Window Defroster

Activating Rear Passenger Climate Controls

• Rotate the rear blower control, located on the main climate control in the instrument panel to the “REAR” position. This enables the rear passenger climate controls located in the headliner above the second row seats.

Page 31

OPERATING YOUR VEHICLE

THREE ZONE AUTOMATIC TEMPERATURE CONTROLS (ATC)

Automatic Operation

• Push the AUTO mode button to activate the ATC system.

• Select the desired temperature by pressing the temperature control buttons for the driver or passenger.

• The system will maintain the set temperature automatically.

Air Conditioning (A/C)

• If the air conditioning button is pressed while in AUTO mode, the system will exit AUTO mode and stay in A/C. The mode and blower will go to the previous user setting.

SYNC Temperature Button

• Push the SYNC button once to control driver and passenger temperatures simultaneously. Push the SYNC button a second time to control the temperatures individually.

Air Recirculation

• Use Recirculation for maximum A/C operation.

• For window defogging, turn the recirculation button off.

• If the Recirculation button is pressed when the system is in Defrost mode the Recirculation LED indicator will flash three times to indicate Recirculation mode is not allowed.

Heated Mirrors

• The mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster.

Rear Window Defroster

Page 32

OPERATING YOUR VEHICLE

Activating Rear Automatic Temperature Control

• Pressing the REAR LOCK button for the Rear Automatic Temperature Control (ATC) System from the front lower ATC panel, illuminates a LOCK symbol in the rear display. The rear temperature and air source are controlled from the front lower ATC panel.

• Rear second row occupants can only adjust the rear ATC control when the REAR LOCK button is turned off.

• The Rear ATC system is located in the headliner, near the center of the vehicle.

PARKSENSE® REAR PARK ASSIST

• If an object is detected behind the rear bumper while the vehicle is in REVERSE, a warning will display in the instrument cluster and a tone will sound, (closer the object the faster the tone) that changes speed depending on the distance of the object from the bumper, will sound.

When the Instrument Cluster reads either “Clean Sensor” or “Blinded”, clean off the bumper

• sensors to see if the condition is corrected.

PARKVIEW® REAR BACK-UP CAMERA

• You can see an on-screen image of the rear of your vehicle whenever the shift lever is put into REVERSE. The ParkView® Rear Back-UpCamera image will be displayed on the radio display screen, located on the center stack of the instrument panel.

• If the radio display screen appears foggy, clean the camera lens located on the liftgate.

WARNING!

Drivers must be careful when backing up; even when using the ParkView® Rear Back-Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You must continue to pay attention while backing up. Failure to do so can result in serious injury or death.

Page 33

OPERATING YOUR VEHICLE

BLIND SPOT MONITORING WITH REAR CROSS PATH

• The Blind Spot Monitoring (BSM) system uses two radar-based sensors, located inside the rear bumper fascia, to detect Highway licensable vehicles (automobiles, trucks, motorcycles etc.) that enter the blind spot zones from the rear/front/side of the vehicle.

• The Blind Spot Monitoring (BSM) system warning light, located in the outside mirrors, will illuminate if a vehicle moves into a blind spot zone.

• The BSM system can also be configured to sound an audible (chime) alert and mute the radio to notify you of objects that have entered the detection zones.

• Refer to your Owner's Manual on the DVD for further details.

POWER SLIDING SIDE DOORS

Automatic/Manual Operation

• The power sliding door may be opened or closed manually or by using the buttons on the Key Fob, overhead console switch, or rear door switch.

•

Pulling the inside or outside power sliding door handle will also power open the power sliding doors.

NOTE:

When the power sliding door master lock switch is in the OFF position, the power sliding side door may not be opened or closed by pressing the switch located on the b-pillar trim panel, just in the front of the sliding door or activating the inside power sliding door handle.

Sliding Side Door Child Protection Lock

• When this system is engaged, the inside manual door handle will not open the sliding door even though the inside door lock is in the unlocked position.

• To engage the Child Protection Door Lock, open the sliding side door. Slide the child protection door lock control, located on the rear of the sliding door, inward (toward the vehicle) to engage.

• Repeat these steps on the opposite sliding door.

Page 34

OPERATING YOUR VEHICLE

POWER LIFTGATE

• The power liftgate may be opened and closed by pressing the button located on the overhead console. Press the button once to open, and a second time to close the power liftgate.

• The power liftgate may also be opened and closed by pressing the button on the Key Fob. Press the button twice to open, and twice to close the power liftgate.

• The power liftgate may be closed by the button, located in the upper left trim in the liftgate opening. Pressing once will only close the liftgate. This button cannot be used to open the liftgate.

POWER SUNROOF

Manual Open/Close

• Press and hold the switch rearward to open or forward to close the sunroof. Any release of the switch will stop the movement, and the sunroof will remain in a partially open or closed position until the switch is pressed again.

Page 35

OPERATING YOUR VEHICLE

Pinch Protection Feat ure

• This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an obstruction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruction if this occurs. Next, press the switch forward and release to Express Close.

NOTE:

If three consecutive sunroof close attempts result in Pinch Protect reversals, the fourth close attempt will be a Manual Close movement with Pinch Protect disabled.

WARNING!

• Never leave children unattended in a vehicle, and do not leave the key in the ignition switch (or leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/Run position). Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.

• In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be severely injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured.

• Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object to project through the sunroof opening. Injury may result.

WIND BUFFETING

• Wind buffeting can be described as a helicopter-type percussion sound. If buffeting occurs with the rear windows open, adjust the front and rear windows together.

• If buffeting occurs with the sunroof open, adjust the sunroof opening, or adjust any window. This will minimize buffeting.

Page 36

ELECTRONICS

YOUR VEHICLE'S SOUND SYSTEM

Page 37

ELECTRONICS

Page 38

ELECTRONICS

Uconnect® 130

NOTE:

Your radio has many features that add to the comfort and convenience of you and your passengers. Some of these radio features should not be used when driving because they take your eyes from the road or your attention from driving.

Clock Setting

• Press and hold the “TIME” button until the hours blink; turn the “TUNE/ SCROLL” control knob to set the hours.

• Press the “TUNE/SCROLL” control knob until the minutes begin to blink; turn the “TUNE/ SCROLL” control knob to set the minutes.

• Press the “TUNE/SCROLL” control knob to save the time change.

• To exit, press any button/knob or wait five seconds.

Equalizer, Balance And Fade

• Press the “TUNE/SCROLL” control knob and BASS, MID, TREBLE, BALANCEand FADE will display. Rotate the “TUNE/SCROLL” control knob to select the desired setting.

Page 39

ELECTRONICS

Radio Operation

Seek Up/Down Buttons

• Press to seek through radio stations in AM or FM bands.

• Hold either button to bypass stations without stopping.

Store Radio Presets

• Press the “SET/RND” button once and SET 1 will show in the display. Then select button (1–6).

• A second station may be added to each push button. Press the “SET/RND” button twice and SET 2 will show in the display. Then select button (1–6).

CD/DISC Operation

Seek Up/Down Buttons

• Press to seek through CD tracks.

• Hold either button to bypass tracks without stopping.

SET/RND Button (Random Play)

• Press this button while the CD is playing to activate Random Play.

• This feature plays the selections on the CD in random order to provide an interesting change of pace.

Audio Jack Operation

• The AUX/Audio Jack provides a means to connect a portable audio device, such as an MP3 player or an iPod®, to the vehicles sound system. This requires the use of a 3.5 mm stereo audio patch cable.

• Pressing the AUX button will change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers.

• The functions of the portable device are controlled using the device buttons, not the buttons on the radio. However, the volume may be controlled using the radio or portable device.

Page 40

ELECTRONICS

Uconnect® 130 WITH SiriusXM SATELLITE RADIO

NOTE:

• Your radio may not be equipped with the Uconnect® Voice Command and Uconnect® Phone features. To determine if your radio has these features, press the VoiceCommand button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating “Uconnect Phone not available” if you do not.

• Your radio has many features that add to the comfort and convenience of you and your passengers. Some of these radio features should not be used when driving because they take your eyes from the road or your attention from driving.

Clock Setting

• Press and hold the “TIME” button until the hours blink; turn the “TUNE/ SCROLL” control knob to set the hours.

• Press the “TUNE/SCROLL” control knob until the minutes begin to blink; turn the “TUNE/ SCROLL” control knob to set the minutes.

• Press the “TUNE/SCROLL” control knob to save the time change.

• To exit, press any button/knob or wait five seconds.

Equalizer, Balance And Fade

• Press the “TUNE/SCROLL” control knob and BASS, MID, TREBLE, BALANCEand FADE will display. Rotate the “TUNE/SCROLL” control knob to select the desired setting.

Page 41

ELECTRONICS

Radio Operation

Seek Up/Down Buttons

• Press to seek through radio stations in AM, FM, or SAT bands.

• Hold either button to bypass stations without stopping.

Store Radio Presets

• Press the “SET/RND” button once and SET 1 will show in the display. Then select button (1–6).

• A second station may be added to each push button. Press the “SET/RND” button twice and SET 2 will show in the display. Then select button (1–6).

Music Type

• Press the “MUSIC TYPE” button to activate this mode. Press the “MUSIC TYPE” button again or turn the “TUNE/SCROLL” control knob to select the desired music type (Adult Hits, Country, Jazz, Oldies, Rock, etc.).

• Once a music type is chosen and the icon is displayed, press either “SEEK” button and the radio will only search for stations with the selected music type.

NOTE:

The Music Type function only operates when in FM mode.

SETUP Button

• Pressing the “SETUP” button allows you to select between items that are available in that particular mode.

• Turn the “TUNE/SCROLL” control knob to scroll through the entries. Push the “AUDIO/ SELECT” button to select an entry and make changes.

SiriusXM Satellite Radio

• SiriusXM Satellite Radio gives you over 130 channels, including 100% commercial-free music from nearly every genre, plus all your favorite sports, news, talk and entertainment channels–all with crystal clear, coast-to-coast coverage, all in one place and all at your fingertips.

• To access SiriusXM Satellite Radio, press the “SAT” hard-key.

Page 42

ELECTRONICS

CD/DISC Operation

Seek Up/Down Buttons

• Press to seek through CD tracks.

• Hold either button to bypass tracks without stopping.

SET/RND Button (Random Play)

• Press this button while the CD is playing to activate Random Play.

• This feature plays the selections on the CD in random order to provide an interesting change of pace.

LIST Button

• Press the “LIST” button to bring up a list of all folders on the CD. Scroll up or down the list by turning the “TUNE/SCROLL” control knob.

• To select a folder from the list, press the “TUNE/SCROLL” control knob and the radio will begin playing the files contained in that folder.

Audio Jack Operation

• Pressing the AUX button will change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers.

• The functions of the portable device are controlled using the device buttons, not the buttons on the radio. However, the volume may be controlled using the radio or portable device.

Page 43

Uconnect® 430/430N

ELECTRONICS

NOTE:

• Your radio may not be equipped with the Uconnect® Voice Command and Uconnect® Phone features. To determine if your radio has these features, press the Voice Command button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating “Uconnect Phone not available” if you do not.

Clock Setting

• Turn the radio on, then touch the screen where the time is displayed.

• Touch the “USER CLOCK” soft-key (Navigation radio only).

• To adjust the hours, touch either the “HOUR FORWARD” or “HOUR BACKWARD” soft-key.

• To adjust the minutes, touch either the “MINUTE FORWARD” or “MINUTE BACKWARD” soft-key.

• To save the new time setting, touch the screen where the word “Save” is displayed.

Page 44

ELECTRONICS

• Press the “MENU” hard-key to access the System Setup menu and the My Files menu.

• Press the “MENU” hard-key in an active mode (SAT, CD, AUX, etc.) to change mode specific settings.

Equalizer, Balance And Fade

Audio Control Menu

• Press the “AUDIO” hard-key on the right side of the radio.

• Use either the arrow soft-keys or the cross-hair on the screen to change Balance and Fade. The “CENTER” soft-key resets the settings.

• Touch the “Equalizer” soft-key and use either the arrow soft-keys or the sliders on the screen to adjust BASS, MID, and/or TREBLE.

Display Settings

• Press the “MENU” hard-key and touch the “Display Settings” soft-key to access the Display Settings menu.

• Select the “Daytime Colors” soft-key to switch to manual daytime mode and to adjust the brightness of the display using daytime colors.

• Select the “Nighttime Colors” soft-key to switch to manual nighttime mode and to adjust the brightness of the display using nighttime colors.

• Select the “Auto Color Mode” soft-key to switch to automatic daytime/nighttime mode and to control the brightness of the display using the dimmer switch of the vehicle.

• Touch the “EXIT” soft-key to save your settings.

Page 45

Radio Operation

ELECTRONICS

• To access Radio Mode, touch the “RADIO” hard-key on the left side of the faceplate, then touch the “AM,” “FM” or “SAT” soft-key at the top of the screen to select the band.

Seek Up/Seek Down

• Press the “Seek Up” or “Seek Down” soft-keys to seek through radio stations in AM, FM, or SAT bands. Hold either Seek to bypass stations without stopping.

Store Radio Presets

• Select the radio band by touching either the “AM,” “FM,” or “SAT” soft-key.

• Find the station to store by either pressing the “Seek Up” or “Seek Down” soft-keys, touching the “SCAN” soft-key, or by using the “DIRECT TUNE” soft-key.

• Once the station is found, touch and hold one of the “PRESET” soft-keys in the list to the right, until you hear a confirmation beep.

NOTE:

If the Presets are not visible on the right side of the screen, press the “Presets” soft-key.

Page 46

ELECTRONICS

CD/DVD Disc Operation

• Press the “MEDIA” hard key to display the media source tabs at the top of the screen. Select the source by touching the “HDD,” “DISC,” or “AUX” media source soft-key tab.

NOTE:

Your Touch-Screen Radio will usually automatically switch to the appropriate mode when something is first connected or inserted into the system.

Insert a CD/DVD Disc

• To insert a disc, press the “LOAD” hard-key.

• With the printed side upwards, insert the disc into the disc slot of the radio. The radio pulls the disc in automatically and closes the flip screen. The radio selects the appropriate mode after the disc is recognized, and starts playing the first track. The display shows “Reading...” during this process.

Seek Up/Seek Down

• Press the “Seek Up” or “Seek Down” soft-keys to seek through tracks in Disc Mode. Hold either Seek to bypass tracks without stopping.

Page 47

ELECTRONICS

Audio Jack Operation

• Press the “MEDIA” hard-key then the “AUX” soft-key to change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers.

• The functions of the portable device are controlled using the device itself, not the buttons on the radio. However, the volume may be controlled using the radio or portable device.

Hard Disk Drive (HDD) Operation

• The Hard Disk Drive (HDD) mode gives you access to the audio files on the internal hard disk drive. It functions similar to a CD player, with the exception that the internal HDD can hold more tracks.

• It is also possible to import display pictures to the internal hard disk drive. The pictures can be displayed on the right half of the radio screen.

• Before using the HDD mode, you will need to copy songs and pictures to the internal hard drive. Songs and pictures can be added to the hard drive by using a CD or USB device (e.g. thumb drive or memory stick).

NOTE:

• HDD supports only .jpg/JPEG formats for photos.

• WMA/MP3 Files and Selective Songs from a CD can also be added to the HDD. See the Uconnect® 430/430N User's Manual for more information.

Copying Music From CD

• Press the “LOAD” hard-key.

• Insert a disc, then press the “MY FILES” hard-key and then select the “MY MUSIC” soft-key.

• Touch the “Add Music Files to HDD” soft-key, then touch the “Disc” soft-key in the next screen to start the process.

NOTE:

• You might need to select the folder or title depending on the CD, then press “DONE” to start the copy process.

• The copy progress is shown in the lower left corner of the screen.

Page 48

ELECTRONICS

Copying Music From USB

• The USB port on the radio face plate allows you to copy files to your hard drive. To access, lift up on the cover.

• Insert a USB device (e.g. thumb drive or memory stick), then select “MY MUSIC soft-key.”

• Touch the “Add Music Files to HDD” soft-key, then touch the “Front USB” soft-key in the next screen.

• Select the folders or titles you would like to copy,thentouch the “DONE” soft-key to start the copy process.

NOTE:

The copy progress is shown in the lower left corner of the screen.

Copying Pictures To The HDD

• Insert either a CD or a USB device containing your pictures in JPEG format.

• Press the “MY FILES” hard-key.

• Touch the “My Pictures” soft-key to get an overview of the currently stored images, then touch the “Add” soft-key.

• Touch the “Disc” or “USB” soft-key, then select the folders or pictures you wish to copy to the HDD. Use the “PAGE” soft-keys to page through the list of pictures.

• Touch the desired pictures or press the “All” soft-key for all pictures. Confirm your selections by touching the “SAVE” soft-key.

NOTE:

The copy progress is shown in the lower left corner of the screen.

Display A Pict ure On The Radio Screen

• Once the import is complete, the pictures will then be available in the “MY PICTURES” screen.

Press the “MY FILES” hard-key, then touch the “My Pictures” soft-key. Touch the desired

• picture, then touch the “Set as Picture View” soft-key and then touch the “Exit” soft-key. Lastly press the “MENU” hard-key and then touch the “Picture View” soft-key to display the chosen picture on the radio screen.

NOTE:

• A check mark in the My Pictures screen indicates the currently used picture.

• You can also delete pictures by touching the “Delete” soft-key.

Page 49

ELECTRONICS

Playing Music From The HDD

• Press the “MEDIA” hard-key to display the media source tabs at the top of the screen. Touch the “HDD” soft-key tab. Touch the desired track soft-key to play or touch the “SEARCH/BROWSE” soft-key to search by artist, by album, by song, by genre, from a folder, or from Favorites.

Cleaning Your Touch-Screen Radio

• Do not spray any liquid or caustic chemicals directly on the screen. Use a clean and dry micro fiber lens cleaning cloth to clean the touch-screen.

• If necessary, use a lint-free cloth dampened with a cleaning solution such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50. Always follow the solvent manufacturer's precautions and directions.

Garmin® Navigation

• Uconnect® 430N integrates Garmin’s consumer-friendly navigation into your vehicle. Garmin® Navigation includes a database with over six million points of interest.

• Touch the “NAV” soft-key in the upper right corner of the screen to access the Navigation system.

Changing the Navigation Voice Prompt Volume

1. Program a destination.

2. While traveling on your route, touch the

upper left area of the map screen where your next turn is displayed.

3. The Navigation system will then repeat

the distance to your next turn.

4. While the Navigation system is speaking, use the ON/OFF VOLUME rotary knob to adjust

the volume to a comfortable level. Please note the volume setting for Navigation Voice Prompt is different than the audio system.

NOTE:

For your own safety and the safety of others, it is not possible to use certain features while the vehicle is in motion.

Page 50

ELECTRONICS

Main Navigation Menu

Finding Points Of Interest

• From the main Navigation menu, touch the “Where To?” soft-key, then touch the “Points of Interest” soft-key.

• Select a Category, then a subcategory, if necessary.

• Select your destination and touch the “Go” soft-key.

Finding A Place By Spelling The Name

• From the Main Navigation Menu touch the “Where To?” soft-key. Next, touch the “Points of Interest” soft-key then touch the “Spell Name” soft-key.

• Enter the name of your destination.

• Touch the “Done” soft-key.

• Select your destination and touch the “Go” soft-key.

Entering A Destination Address

From the main Navigation menu touch the “Where To?” soft-key, then touch the “Address”

• soft-key.

• Follow the on-screen prompts to enter the address then touch the “Go” soft-key.

Searching Near Another Location

• From the main Navigation menu touch the “Where To?” soft-key. Next, touch a destination then touch the “Near” soft-key.

• Select an option from the available choices.

Setting Your Home Location

• From the main Navigation menu touch the “Where To?” soft-key, then touch the “Go Home” soft-key.

• You may enter your address directly, use your current location as your home address, or choose from recently found locations.

Edit Home Location

From the main Navigation menu touch the “Where To?” soft-key, then touch the “Favorites”

• soft-key.

• Next touch the location you would like to edit, touch the “Press for More” soft-key, then the “Edit” soft-key.

Go Home

• A Home location must be saved in the system. From the Main Navigation menu, touch the “Where To?” soft-key, then touch the “Go Home” soft-key.

Page 51

ELECTRONICS

Following Your Route

Your route is marked with a magenta line on the map. If you depart from the original route,

• your route is recalculated. A speed limit icon could appear as you travel on major roadways.

Adding A Via Point

• To add a stop between the current location and the end destination (Via Point) you must be navigating a route.

• Touch the “back arrow” icon multiple times to return to the Main Navigation menu.

• Touch the “Where To?” soft-key, then search for the additional stop. Select the Via Point you wish to add from the given search results.

• Touch the “Go” soft-key, then touch the “Add to Current Route” soft-key.

Taking A Detour

• To take a detour you must be navigating a route.

•

Touch the “back arrow” icon soft-key multiple times to return to the Main Navigation menu.

• Touch the “Detour” soft-key.

NOTE:

If the route you are currently taking is the only reasonable option, the device might not calculate a detour.

Acquiring Satellites

• The GPS Satellite strength bars indicate the strength of your satellite reception.

• Acquiring satellite signals can take a few minutes. When at least one of the bars is green, your device has acquired satellite signals.

• You may experience delays receiving satellite signals when in areas with an obstructed view to the sky, such as garages, tunnels, or large cities with tall buildings.

Page 52

ELECTRONICS

Uconnect® 730N

NOTE:

Clock Setting

• Turn the radio on, then touch the screen where the time is displayed.

• Touch the “USER CLOCK” soft-key.

• To adjust the hours, touch either the “HOUR FORWARD” or “HOUR BACKWARD” soft-key.

• To adjust the minutes, touch either the “MINUTE FORWARD” or “MINUTE BACKWARD” soft-key.

• To save the new time setting, touch the screen where the word “Save” is displayed.

• Press the “MENU” hard-key to access the System Setup menu and the My Files menu.

• Press the “MENU” hard-key in an active mode (SAT, CD, AUX, etc.) in order to change mode specific settings.

Page 53

ELECTRONICS

Equalizer, Balance And Fade

Audio Control Menu

• Press the “MENU” hard-key on the right side of the radio. Then press the “Audio Control” soft-key to get to the audio control menu.

• Use either the arrow soft-keys or the cross-hair on the screen to change Balance and Fade. The “CENTER” soft-key resets the settings.

• Touch the “Equalizer” soft-key and use either the arrow soft-keys or the sliders on the screen to adjust BASS, MID, and/or TREBLE.

Display Settings

• Press the “MENU” hard-key and touch the “Display Settings” soft-key to access the Display Settings menu.

• Select the “Daytime Colors” soft-key to switch to manual daytime mode and to adjust the brightness of the display using daytime colors.

• Select the “Nighttime Colors” soft-key to switch to manual nighttime mode and to adjust the brightness of the display using nighttime colors.

• Select the “Auto Color Mode” soft-key to switch to automatic daytime/ nighttime mode and to control the brightness of the display using the dimmer switch of the vehicle.

• Touch the “EXIT” soft-key to save your settings.

Page 54

ELECTRONICS

Radio Operation

• To access Radio Mode, touch the “RADIO/MEDIA” hard-key on the left side of the faceplate repeatedly until AM/FM/SAT appears at the top of the screen, then touch the “AM,” “FM” or “SAT” soft-key to select the band.

Seek Up/Seek Down

• Press the “Seek Up” or “Seek Down” hard-keys to seek through radio stations in AM, FM, or SAT bands. Hold either Seek to bypass stations without stopping.

Store Radio Presets

• Select the radio band by touching either the “AM,” “FM,” or “SAT” soft-key.

• Find the station to store by either pressing the “Seek Up” or “Seek Down” hard-keys, touching the “SCAN” soft-key, or by using the “DIRECT TUNE” soft-key.

• Once the station is found, touch and hold one of the PRESET soft-keys in the list to the right, until you hear a confirmation beep.

NOTE:

If the Presets are not visible on the right side of the screen, press the “Presets” soft-key.

Page 55

CD/DVD Disc Operation

ELECTRONICS

• Press the “RADIO/MEDIA” hard-key until the media source tabs are displayed at the top of the screen. Select the source by touching the “HDD,” “DISC,” or “AUX” media source soft-key tab.

NOTE:

Your Touch-Screen Radio will usually automatically switch to the appropriate mode when something is first connected or inserted into the system.

Insert a CD/DVD Disc

• To insert a disc, press the “OPEN/CLOSE” hard-key.

Seek Up/Seek Down

• Press the “Seek Up” or “Seek Down” hard-keys to seek through tracks in Disc Mode. Hold either Seek to bypass tracks without stopping.

Page 56

ELECTRONICS

Audio Jack Operation

• Press the “RADIO/MEDIA” hard-key, then the “AUX” soft-key to change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers.

• The functions of the portable device are controlled using the device itself, not the buttons on the radio. The volume may be controlled using the radio or portable device.

Hard Disk Drive (HDD) Operation

• It is also possible to import display pictures to the internal hard disk drive. The pictures can be displayed on the right half of the radio screen.

NOTE:

• HDD supports only .jpg/JPEG formats for photos.

• WMA/MP3 Files and Selective Songs from a CD can also be added to the HDD. See the Uconnect® 730N User's Manual for more information.

Copying Music From CD

• Press the “OPEN/CLOSE” hard-key.

• Insert a disc, then press the “MENU” hard-key.

• Touch the “MY FILES” soft-key, then select “MY MUSIC.”

• Touch the “Add Music Files to HDD” softkey, then touch the “From Disc” soft-key in the next screen to start the process.

NOTE:

• You might need to select the folder or title depending on the CD, then press “Done” to start the copy process.

• The copy progress is shown in the lower left corner of the screen.

Copying Music From USB

• The USB port on the radio face plate allows you to copy files to your hard drive. To access, lift up on the cover.

• Insert a USB device (e.g. thumb drive or memory stick), then select “MY FILES”.

Page 57

ELECTRONICS

• Touch the “MY MUSIC” soft-key, then touch the “Add Music Files” to HDD soft-key.

• Touch the “From USB” soft-key, then select the folders or titles you would like to copy, and then touch the “SAVE” soft-key to start the copy process.

NOTE:

The copy progress is shown in the lower left corner of the screen.

Copying Pictures To The HDD

• Insert either a CD or a USB device containing your pictures in JPEG format.

• Press the “MENU” hard-key to access the Settings Menu, then touch the “My Files” soft-key.

• Touch the “My Pictures” soft-key to get an overview of the currently stored images, then touch the “Add” soft-key.

• Touch the “From Disc” or “From USB” soft-key, then select the folders or pictures you wish to copy to the HDD. Use the “PAGE” soft-keys to page through the list of pictures.

Touch the desired pictures or press the “All”

• soft-key for all pictures. Confirm your selections by touching the “SAVE” soft-key.

NOTE:

The copy progress is shown in the lower left corner of the screen.

Display A Pict ure On The Radio Screen

• Once the import is complete, the pictures will then be available in the “MY PICTURES” screen.

• Press the “MENU” hard-key to access the Settings Menu, then touch the “My Files” soft-key and then touch the “My Pictures” soft-key. Touch the desired picture, then touch the “Set as Picture View” soft-key and then touch the “Exit” soft-key. Lastly press the “MENU” hard-key and then touch the “Picture View” soft-key to display the chosen picture on the radio screen.

NOTE:

• A check mark in the My Pictures screen indicates the currently used picture.

• You can also delete pictures by touching the “Delete” soft-key.

Page 58

ELECTRONICS

Playing Music From The HDD

• Press the “RADIO/MEDIA” hard-key until the media source tabs are displayed at the top of the screen. Touch the “HDD” soft-key tab. Touch the desired track soft-key to play or touch the “SEARCH/BROWSE” soft-key to search by artist, by album, by song, by genre, from a folder, or from Favorites.

Cleaning Your Touch-Screen Radio

• Do not spray any liquid or caustic chemicals directly on the screen. Use a clean and dry micro fiber lens cleaning cloth to clean the touch-screen.

NAVIGATION

• Your navigation system receives GPS signals from up to 16 satellites to display the position of your vehicle. Map and database information is supplied through a hard disk drive.

• Touch the “NAV” hard-key on the radio face plate to access the Navigation system and the NAV – Main Menu.

Changing the Navigation Guidance Prompt Volume

1. From the Navigation Map screen, touch the Menu hard-key and then touch the Guidance Prompts soft-key.

Select and adjust the navigation guidance prompt volume using the left and right arrows.

3. Touch the “SAMPLE VOL” soft-key to lis-

ten to the current volume setting.

4. Once satisfied with the volume, touch the

“SAVE” soft-key to save the settings. Touch the “CANCEL” soft-key to exit the menu without saving the settings.

NOTE:

For your own safety and the safety of others, it is not possible to use the certain features while the vehicle is in motion.

Page 59

Main Navigation Menu

ELECTRONICS

Finding Points Of Interest

• From the NAV main menu, touch the “Points of Interest” soft-key.

• Select a Category and then a subcategory, if necessary.

• Select your destination and touch “GO.”

Finding A Place By Entering The Street Address

• From the NAV main menu, touch “New Destination,” then touch “Street Address.”

NOTE:

If the State and/or Country displayed are incorrect, touch the corresponding soft-key to make the correction.

• Once the Country and State are set and the Street Address screen is displayed, begin spelling the street name in the speller. In the upper right corner the number of possible roads decreases.

• Touch the “LIST” soft-key to display a list of possible street names. Select the correct street name.

• Next input the number.

• In the Confirm Route screen the navigation radio displays the complete address, a map of the destination area, and the current routing method for you to verify.

• Touch the “GO” soft-key to activate the route guidance.

Page 60

ELECTRONICS

Entering Your Home Location

• Press the “NAV” hard-key on the right side of the radio.

• From the Nav – Main Menu, touch “Guide Me Home” to enter your home address. If no home address has been set, touch “YES” to access the Enter Home Address menu.

• Touch “Street Address” to enter your address. Touch the soft-key with your state’s name and enter your street name into the speller.

• Once the street name has been input, touch “CONTINUE” to confirm. Enter the house number into the next screen. If more than one city has this address, you will then need to select your city from a list.

• Once the address is entered completely, the system shows a map of your home address area. Touch “SAVE” to confirm the address. The system will then ask if you want to go there. Touch the “Yes” or “No” soft-key.

Change Home Address

• This procedure will allow you to change your Home Address if one has already been entered.

• Press the “MENU” hard-key, touch “My Files” and then touch “My Address Book.”

• Touch “Home,” then touch “Edit Contacts” and then “Change Address.”

• Touch the soft-key with your state’s name and enter your street name into the speller.

• Once the street name has been input, touch “CONTINUE” to confirm.

• Enter the house number into the next screen. If more than one city has this address, you will then need to select your city from a list.

• Touch the “SAVE” soft-key to confirm the address.

Go Home

• From the NAV main menu, touch “Guide Me Home” when you want to route to your home destination.

Where Am I Now?

• From the NAV main menu, touch “Where Am I Now?”. The Where Am I Now? menu displays location information for the current vehicle position.

• Touch the “NEARBY POI” soft-key to search for a local Point of Interest.

• Touch the “SAVE LOCATION”soft-key to save the current location in the Saved Locations memory.

Page 61

Route Guidance

ELECTRONICS

• After starting route guidance, the system calculates the route and announces: “Follow the arrows on the display.” You will receive navigation recommendations by voice messages and screen displays.

Route Options

• After pressing the “OPTIONS” soft-key in the Route Guidance Menu, the following information is displayed:

• In the left half of the screen, the current position and the current routing method are

displayed.

• “Take Detour” will allow you to calculate a different route.

• “Find Nearby POI” to search for a local POI.

• “Destination Info” displays destination information.

• “View Turn List” lists streets utilized for the current route.

• “Save Destination” to save the destination address.

• “Change Method” will allow you to change the routing method.

Page 62

ELECTRONICS

SiriusXM SATELLITE RADIO/TRAVEL LINK

• SiriusXM Travel Link requires a subscription, sold separately after the 1 year trial subscription included with your vehicle purchase.

• SiriusXM Travel Link is only available in the United States. The following describes features that are available when in SiriusXM Satellite Radio mode.

•

• To access SiriusXM Satellite Radio, press the “RADIO/MEDIA” or “RADIO” and then touch the “SAT” soft-key tab.

Info

• Touch the “i” soft-key to view detailed information about the current Sirius XM Satellite channel.

SiriusXM Parental Controls

• SiriusXM offers the option to permanently block selected channels. Call 1-888-539-7474 and request the Family Package.

• Uconnect® 430/430N and 730N: Press the “MENU” hard-key while in SiriusXM Satellite Radio Mode, then touch the “Channel Lock” to enable and/or disable desired channels. The SEEK and SCAN function will then only display channels without Channel lock.

Search/Browse

• Touch the “magnifying glass” soft-key to search/browse the SiriusXM channel listing by Favorites and Categories such as Song, Artist and Channel Name. The Search/Browse also allows you manage your Favorites.

SiriusXM Satellite Radio Favorites (SAT Favorites)

• You can save 50 favorite songs and 50 favorite artists.

• Touch the “Add Favorite” soft-key to add either the song or the artist of the currently playing program to the SAT Favorites list. The favorite star will appear in the upper right corner, below the “SAT” softkey .

Page 63

ELECTRONICS

• You will see a favorite star indicator in the upper right side of the screen below the “SAT” soft-keyand a pop up will alert you that a favorite song or artist is currently playing on one of the SiriusXM satellite radio channels.

NOTE:

Refer to your Uconnect® 730N or 430/430N User's Manual for more information.

Display SAT Favorites List

• Touch the “Search/Browse” soft-key and select “Favorites” from the SAT Browse screen.

• Touch the desired favorites soft-key to switch the SAT tuner to the corresponding channel.

• You may use the “LIST” soft-key to toggle between:

• Favorite Songs

• Favorite Artists

• Currently playing favorites

Replay

• While you are in SAT mode, you can replay 44 minutes of the current SiriusXM channel (when the channel is changed, this audio buffer is erased). Press the REPLAY button to listen to the stored audio.

• You can touch the on-screen controls to pause and rewind audio playback, touch the SCAN button to preview each of the tracks stored in the buffer, or select a track from the list.

• The time displayed below the bar indicates how much time is present between the current buffer play position and the live broadcast.

Replay Option Option Description

Play/Pause Touch to pause content playback. Touch Pause/Play again to resume

playback.

Rewind/RW Rewinds the channel content in steps of five seconds. Touch and hold to

rewind continuously, then release to begin playing content at that point.

Fast Forward/FW Forwards the content, and works similarly to Rewind/RW. However, Fast

Forward/FW can only be used when content has been previously rewound.

Page 64

ELECTRONICS

Replay Option Option Description

Replay Time Displays the amount of time in the upper center of the screen by which your

content lags the live channel.

Live Resumes playback of live content at any time while replaying rewound

content.

SiriusXM Travel Link (Uconnect® 730N & Uconnect® 430N Only)

NOTE:

• SiriusXM Travel Link requires a subscription, sold separately after the 1 year trial subscription included with your vehicle purchase.

• SiriusXM Travel Link is only available in the United States.

• SiriusXM Travel Link brings a wealth of useful information into your vehicle and right to your fingertips.

• To access Travel Link, press the MENU hard-key, then the Travel Link soft-key.

1 – Favorites

2 – Forecast

3 – Ski Info 4 – Fuel Prices 5 – Movies 6 – Sports

View and store your favorite location, theater and sport teams for quick access.

View detailed weather conditions, forecasts and ski/snowboarding conditions at resorts.

View ski and snowboarding conditions at ski resorts. View detailed price information for fuel stations. View information on movies that are playing at theaters. View sports scores and upcoming events for all major sports.

Page 65

ELECTRONICS

STEERING WHEEL AUDIO CONTROLS

• The steering wheel audio controls are located on the rear surface of the steering wheel.

Right Switch

• Press the switch up or down to increase or decrease the volume.

• Press the button in the center to change modes AM/FM/CD/SAT.

Left Switch

• Press the switch up or down to search for the next listenable station or select the next or previous CD track.

• Press the button in the center to select the next preset station (radio) or to change CDs if equipped with a CD Changer.

iPod®/USB/MP3 CONTROL

•

There are many ways to play music from iPod®/MP3 players or USB devices through your vehicle's sound system.

• The remote USB port, located within the upper glove box, allows you to plug an iPod® into the vehicle's sound system.

NOTE:

If equipped with the Uconnect® 730N, the USB port on the faceplate allows the same functions as the remote USB port.

• Non-Touch-Screen Radios: To hear audio from devices connected to the USB port, press the “AUX” button on the radio faceplate.

• Touch-Screen Radios: To hear audio from devices connected to the USB port, press the “MEDIA” hard-key, then touch the “AUX” or “iPod®” soft-key.

• When connected to this feature:

• The iPod® can be controlled using the radio buttons to Play, Browse, and List the iPod® or external devices contents.

•

The iPod® battery charges when plugged into the USB port (if supported by the specific audio device).

• Compatible iPod® devices may also be controllable using voice commands. Refer to the Owner's Manual on the DVD for details.

Page 66

ELECTRONICS

NOTE:

The USB port supports certain Mini, Classic, Nano, Touch, and iPhone® devices. The USB port also supports playing music from compatible external USB Mass Storage Class memory devices. For supported audio file formats, refer to the USB Port section in the Owner's Manual on the DVD. Refer to www.UconnectPhone.com for a list of tested iPod®s. Some iPod® software versions may not fully support the USB port features. Please visit Apple’s website for iPod® software updates.

WARNING!

Do not plug in or remove the iPod® or external device while driving. Failure to follow this warning could result in a collision.

Uconnect® Phone

• To determine if your vehicle is equipped with Uconnect® Phone, press the “Uconnect® Phone” button will hear a voice prompt. If not, you will see a message on the radio “Uconnect phone not available”.

located on the radio faceplate. If your vehicle has this feature, you

• The Uconnect® Phone is a voice-activated, hands-free, in-vehicle communications system with Voice Command Capability (see Voice Command section).

NOTE:

To access the tutorial, press the “Uconnect® Phone” button “tutorial.” Press any hard-key/button or touch the display (Touch-Screen radio) to cancel the “tutorial”.

• The Uconnect® Phone allows you to dial a phone number with your mobile phone using simple voice commands.

• Refer to your vehicle Owner's Manual on the DVD for further details.

NOTE:

The Uconnect® Phone requires a mobile phone equipped with the Bluetooth® Hands-Free Profile, Version 1.0 or higher. For Uconnect® Customer Support: U.S. residents - visit www.UconnectPhone.com or call 1–877–855–8400. Canadian Residents - call, 1-800-465– 2001 (English) or 1-800-387-9983 (French). This site will provide specific instructions based on the type of mobile phone being paired.

Phone Pairing

NOTE:

• Pairing is a one - time initial setup before using the phone.

. After the BEEP, say

• Prior to starting the pairing procedure ensure all additional phones within the vehicle have their Bluetooth® disabled.

• Press the “Phone”

button to begin.

Page 67

ELECTRONICS

• Wait for the “ready” prompt and BEEP.

• After the BEEP, say ”setup” or “Uconnect device setup”.

• After the BEEP, say “device pairing”.

• After the BEEP, say “pair a device”.

• Follow the audible prompts.

• You will be asked to say a four-digit Personal Identification Number (PIN), which you will later need to enter into your mobile phone. You can say any four-digit PIN. You will not need to remember this PIN after the initial pairing process.

• You will then be prompted to give the phone pairing a name (each phone paired should have a unique name).

• Next you will be asked to give this new pairing a priority of 1 through 7 (up to seven phones may be paired); 1 is the highest and 7 is the lowest priority. The system will only connect to the highest priority phone that exists within the proximity of the vehicle.

• You will then need to start the pairing procedure on your cell phone. Follow the Bluetooth® instructions in your cell phone Owner's Manual to complete the phone pairing setup.

Phonebook

Phonebook Download – Automatic Phonebook Transfer From Mobile Phone

• If equipped and specifically supported by your phone, Uconnect® Phone automatically downloads names (text names) and number entries from your mobile phone’s phonebook. Specific Bluetooth® Phones with Phone Book Access Profile may support this feature.AutomaticTransferis indicated by a green arrowat the bottom of the screen. See www.UconnectPhone.com for supported phones.

• Automatic download and update, if supported, begins as soon as the Bluetooth® wireless phone connection is made to the Uconnect® Phone. For example, after you start the vehicle.

NOTE:

The mobile phone may require authorization prior to download.

• A maximum of 1000 entries per phone will be downloaded and updated every time a phone is connected to the Uconnect® Phone.

• Depending on the maximum number of entries downloaded, there may be a short delay before the latest downloaded names can be used. Until then, if available, the previously downloaded phonebook is available for use.

• Only the phonebook of the currently connected mobile phone is accessible.

Page 68

ELECTRONICS

• Only the mobile phone’s phonebook is downloaded. The SIM card phonebook is not part of the Mobile phonebook.

• This downloaded phonebook cannot be edited or deleted on the Uconnect® Phone. These can only be edited on the mobile phone. The changes are transferred and updated to Uconnect® Phone on the next phone connection.

Making A Phone Call

• Press the “Phone” button

• After the BEEP, say “dial” (or “call” a name).

• After the BEEP, say number (or name).

Receiving A Call – Accept (And End)

• When an incoming call rings/is announced on Uconnect®, press the Phone button

• To end a call, press the Phone button

Mute (Or Unmute) Microphone During Call

• During a call, press the “Voice Command” button

• After the BEEP, say “mute” (or “mute off”).

Transfer Ongoing Call Between Handset And Vehicle

• During a call, press the “Voice Command” button

• After the BEEP, say “transfer call”.

Changing The Volume

• Start a dialogue by pressing the “Phone” button normal call.

, then adjust the volume during a

• Use the radio ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Uconnect® system is speaking. Please note the volume setting for Uconnect® is different than the audio system.

• Any voice commanded system should be used only in safe driving conditions following applicable laws regarding phone use. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing you and others to be severely injured or killed.

• In an emergency, to use Uconnect® Phone, your mobile phone must be:

• turned on,

• paired to Uconnect® Phone,

• and have network coverage.

WARNING!

Page 69

ELECTRONICS

Uconnect® VOICE COMMAND

Voice Command Operation

• The Uconnect® VoiceCommand system allows you to control your AM, FM radio, satellite radio, disc player, HDD, Uconnect® Phone, a memo recorder, and supported portable media devices.

• When you press the “Voice Command” button steering wheel, you will hear a beep. The beep is your signal to give a command. If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the “Voice Command” button

NOTE:

Visit http://www.driveuconnect.com/features/voiceCommand/ for more info on which voice command features apply to your vehicle.

• Start a dialogue by pressing the “Voice Command” button The beep is your signal to give a command. Below are a list of voice commands for each of the different modes.

Common Voice Commands (Examples)

, listen for the BEEP, and say your command.

located on the radio faceplate or

, you will hear a beep.

While In: Voice Command Example:

Main Menu

Radio Mode

“Radio AM” (to switch to the AM radio mode)

“Radio FM” (to switch to the FM radio mode)

“Satellite Radio” (to switch to the Satellite radio mode)

“Disc” (to switch to the disc mode) “USB” (to switch to the USB mode)

“Bluetooth Streaming” (to switch to the Bluetooth Streaming mode)

“Memo” (to switch to the memo recorder)

“System Setup” (to switch to system setup)

“Frequency” (to change the frequency)

“Next Station” (to select the next station)

“Previous Station” (to select the previous station)

“Radio Menu” (to switch to the radio menu)

“Main Menu” (to switch to the main menu)

Page 70

ELECTRONICS

“Channel Number” (to change the channel by its spoken number)

“Previous Channel” (to select the previous channel)

SiriusXM Satellite

Radio Mode

Disc Mode

Memo Mode

To switch to the voice recorder mode, say “Memo”. The following are

common voice commands for this mode: “New Memo” (to record a new

button

— “Play Memos” (to play previously recorded memos) — During the play-

back you may press the Voice Command button to stop playing

“List Channel” (to hear a list of available channels)

"Channel Name" (to change the channel by its spoken name)

memo) — During the recording, you may press the Voice Command

memos. You proceed by saying one of the following commands:

“Next Channel” (to select the next channel)

“Select Name” (to say the name of a channel)

“Radio Menu” (to switch to the radio menu)

“Main Menu” (to switch to the main menu)

“Track” (#) (to change the track)

“Next Track” (to play the next track)

“Previous Track” (to play the previous track)

“Main Menu” (to switch to the main menu)

to stop recording. You proceed by saying one of the

following commands:

— “Save” (to save the memo)

— “Continue” (to continue recording)

— “Delete” (to delete the recording)

— “Repeat” (to repeat a memo)

— “Next” (to play the next memo)

— “Previous” (to play the previous memo)

— “Delete” (to delete a memo)

— “Delete All” (to delete all memos)

Voice Text Reply

• If equipped with Uconnect® Voice Command, your Uconnect® 430N, 730N & 731N radios may be able to play incoming Short Message Service (SMS) messages (text messages) through the vehicle's sound system.

• It also allows you to respond by selecting from various pre - defined phrases.

• Not all phones are compatible with this feature. Refer to the phone compatibility list at www.UconnectPhone.com. Connected mobile phones must be bluetooth-compatible and paired with your radio.

• Press the “Voice Command” button

NOTE:

To access the tutorial, press the “Voice Command” button “tutorial”. Press any hard-key/button or touch the display (Touch-Screen radio) to cancel the tutorial.

and after the BEEP, say “SMS”to get started.

. After the BEEP, say

Page 71

ELECTRONICS

WARNING!

Any voice commanded system should be used only in safe driving conditions following applicable laws regarding phone use. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing you and others to be severely injured or killed.

Bluetooth® STREAMING AUDIO

• If equipped with Uconnect® Voice Command, your Bluetooth-equipped iPod® devices, cell phones or other media players, may also be able to stream music to your vehicles speakers. Your connected device must be Bluetooth-compatible, and paired with your radio (see Uconnect® Phone for pairing instructions).

Non-Touch-Screen Radios: Press the “AUX”

• button on the radio faceplate until "BT" or “Audio Streaming” is displayed on the radio screen.

• Touch-Screen-Radios: Press the “RADIO/MEDIA”or“MEDIA” hard-key and then touch the “AUX” soft-key tab.

VIDEO ENTERTAINMENT SYSTEM (VES™)

System Operation

The screen is located in the overhead com-

• partment console. To lower the screen, press the release button located in the center of the console rear of the screen.

• The system may be controlled by the front seat occupants using either the radio or DVD player controls, or by the rear seat occupants using the remote control.

• The video screen displays information in a split screen format. The left side of the screen is referredto as Channel 1 and the right side of the screen is referredto as Channel

2. All modes except video modes are displayed in a split screen format.

• To use the headphones, press the power button located on the right ear cup. Select the channel on the headphones (1 or 2) which corresponds to the channel selected on the desired video screen.

• To receive VES™ audio through the vehicle's sound system, press the VES™ soft-key on the radio's touch-screen.

Page 72

ELECTRONICS

Operation Of The Touch-Screen Radio/DVD Player/Blu-Ray Player

• To view a DVD press the OPEN/CLOSE or LOAD hard-key on the touch-screen radio and insert the disc or insert the disc into the optional DVD player. Playback will begin automatically after the DVD is recognized by the disc drive. If playback does not begin automatically when the disc is inserted into the DVD player press the PLAY button. If playback does not begin automatically after the disc is inserted into the touch-screen radio follow these steps:

• Press the MENU hard-key, then touch the Rear VES™ soft-key. If a chapter list appears on the right side of the screen, touch the HIDE LIST soft-key to display the Rear VES™ control screen.

• Touch the 1 soft key to select an audio channel, then touch the DISC soft-key in the MEDIA column.

Operation Of The Remote Control

• The remote control operates similarly to any DVD remote you may have used before and allows the rear seat passengers to change stations, tracks, discs and audio/video modes.

• The remote control is designed to control either channel by using the selector switch located on the right side of the remote.

• Connect the video game or other external media devices to the AUX jacks following the color coding for the VES™ jacks.

• Pressing the power button will turn the VES™ system ON/OFF.

• Pressing the mode button causes the MODE SELECTION menu to appear on the VES™ screen. Use the remote control arrow buttons to scroll through the available modes, and then press ENTER to select the desired mode.

Auxiliary Audio/Video Input Jacks

• The AUX jacks are located on the drivers side rear trim panel behind the sliding door.

• Connect the video game or other external media devices to the AUX jacks following the color coding for the VES™ jacks.

• Using either the touch-screen radio or remote control, select AUX from the REAR VES™ CONTROL or the MODE SELECTION screen.

• Refer to the Uconnect® Multimedia – Video Entertainment System (VES™) section in the vehicle Owner's Manual on the DVD for further details.

Page 73

ELECTRONICS

ELECTRONIC VEHICLE INFORMATION CENTER (EVIC)

• The EVIC features a driver interactive display that is located in the instrument cluster. Pressing the controls on the left side of the steering wheel allows the driver to select vehicle information and Personal Settings. For additional information, refer to “Programmable Features” located in this guide.

• Press and release the UP scroll upward through the main menus (Fuel Economy, Vehicle Info, Tire PSI, Cruise, Messages, Units, System Setup) and sub menus.

• Press and release the DOWN sub menus.

• Press and release the SELECT select a personal setting in the setup menu.

• Press the BACK button to scroll back to a previous menu or sub menu.

Compass Calibration

• This compass is self-calibrating, which eliminates the need to set the compass manually. When the vehicle is new, the compass may appear erratic and the EVIC will display “CAL” until the compass is calibrated.

• You may also calibrate the compass by completing one or more 360 degree turns (in an area free from large metal or metallic objects) until the “CAL” message displayed in the EVIC turns off. The compass will now function normally.

button to

button to scroll downward through the main menus and

button for access to main menus, sub menus or to

Page 74

ELECTRONICS

PROGRAMMABLE FEATURES

Electronic Vehicle Information Center (EVIC) – If Equipped

• The EVIC can be used to program the following Personal Settings. Press and release the MENU button until Personal Settings displays, then press the DOWN button scroll through the settings. Press the SELECT button

• Language • Intermittent Wiper Option

• Nav-Turn By Turn • Rain Sensing Wipers

•

Enable/Disable the Rear Park Assist System

• Auto Unlock Doors • Illuminated Approach

• Remote Unlock Sequence • Flashers with Sliding Door

• RKE Linked To Memory • Hill Start Assist (HSA)

• Remote Start Comfort Sys. • Keyless Enter-N-Go™ (Passive Entry)

• Horn With Remote Lock • Easy Exit Seat

• Horn With Remote Start • Tilt Mirror In Reverse

• Flash Lamps With Lock • Blind Spot Alert

• Automatic High Beams • Calibrate Compass

• Headlamp Off Delay • Compass Variance

• Headlamps with Wipers (Available with Auto Headlights Only)

• Key-Off Power Delay

• Turn Menu Off

to change the setting.

Key Fob Programmable Features

• The following features may also be programmed by using the Key Fob transmitter or the ignition switch and driver's door lock switch.

NOTE:

Pressing the LOCK button while you are inside the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Vehicle Security Alarm.

Unlock On First Press

• To unlock either the driver's side, or all doors, on the first press of the UNLOCK button:

Press and hold the LOCK button for at least four seconds, but no longer than 10 seconds.

• Then, press and hold the UNLOCK button while still holding the LOCK button.

• Release both buttons at the same time.

Auto Unlock Doors On Exit

• To have all of the vehicle doors unlock when any door is opened:

• Enter your vehicle and close all the doors, and fasten your seat belt.

• Cycle the ignition switch between the LOCK and ON position four times, ending in the LOCK position (do not start the engine).

• Press the power door UNLOCK switch to unlock the doors. A single chime will indicate that programming is complete.

Page 75

ELECTRONICS

Sound Horn With Lock

• To turn the horn chirp on or off when the doors are locked:

• Press the LOCK button for at least four seconds, but no longer than 10 seconds. Then, press the PANIC button while still holding the LOCK button.

• Release both buttons at the same time.

Flashing Lights With Lock

• The turn signal lights flashing, when the doors are locked or unlocked, feature can be turned on or off. To turn this feature on or off:

Press and hold the UNLOCK button for at least four seconds, but no longer than 10 sec-

• onds. Then, press and hold the LOCK button while still holding the UNLOCK button.

• Release both buttons at the same time.

UNIVERSAL GARAGE DOOR OPENER (HomeLink®)

•

HomeLink® replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink® unit is powered by your vehicles 12 Volt battery.

• The HomeLink® buttons that are located in the overhead console or sunvisor designate the three different HomeLink® channels.

• The HomeLink® indicator is located above the center button.

Before You Begin Programming HomeLink®

• Ensure that your vehicle is parked outside of the garage before you begin programming.

• For efficient programming and accurate transmission of the radio-frequency signal, it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system.

• Erase all channels before you begin programming. To erase the channels, place the ignition switch into the ON/RUN position, then press and hold the two outside HomeLink® buttons (I and III) for up to 20 seconds or until the red indicator flashes.

NOTE:

Erasing all channels should only be performed when programming HomeLink® for the first time. Do not erase channels when programming additional buttons.

• If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance.

Page 76

ELECTRONICS

Programming A Rolling Code

• For programming Garage Door Openers that were manufactured after 1995. These Garage Door Openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the Garage Door Opener. It is NOT the button that is normally used to open and close the door.The name and color of the button may vary by manufacturer.

• Place the ignition switch into the ON/RUN position.

• Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view.

• Simultaneously press and hold both the HomeLink® button you want to program and the hand-held transmitter button.

• Continue to hold both buttons and obser ve the indicator light. The HomeLink® indicator will flash slowly and then rapidly after HomeLink® has received the frequency signal from the hand-held transmitter. Release both buttons after the indicator light changes from slow to rapid.

• At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor. Firmly press and release the “LEARN” or “TRAINING” button.

NOTE:

You have 30 seconds in which to initiate the next step after the LEARN button has been pressed.

• Return to the vehicle and press the programmed HomeLink® button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete.

NOTE:

If the device does not activate, press the button a third time (for two seconds) to complete the training.

• To program the remaining two HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels.

Programming A Non-Rolling Code

• For programming Garage Door Openers manufactured before 1995.

• Turn the ignition switch to the ON/RUN position.

• Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view.

• Simultaneously press and hold both the HomeLink® button you want to program and the hand-held transmitter button.

Page 77

ELECTRONICS

• Press and hold the programmed HomeLink® button and observe the indicator light.

NOTE:

• If the indicator light stays on constantly, programming is complete and the garage door (or device) should activate when the HomeLink® button is pressed.

• To program the two remaining HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels.

Using HomeLink®

• To operate, press and release the programmed HomeLink® button. Activation will now occur for the programmed device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The hand-held transmitter of the device may also be used at any time.

WARNING!

• Your motorized door or gate will open and close while you are programming the universal transceiver. Do not program the transceiver if people or pets are in the path of the door or gate.

• Do not run your vehicle in a closed garage or confined area while programming the transceiver. Exhaust gas from your vehicle contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous when inhaled and can cause you and others to be severely injured or killed.

POWER INVERTER

• There is a 115 Volt,150 Watt power inverter outlet located on the left rear trim panel immediately behind the second row left passenger seat. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts.

• Press the switch located in the center of the instrument panel to turn the power to the outlet on.

• Press the switch again to turn the power off.

• The status indicator of the AC power inverter indicates whether the inverter is producing AC power.

Page 78

ELECTRONICS

NOTE:

The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet, the inverter should automatically reset. If the power rating exceeds approximately 170 Watts, the power inverter may have to be reset manually. To reset the inverter manually, unplug the device and plug it in again. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter.

WARNING!

• To Avoid Serious Injury or Death DO NOT:

• insert any objects into the receptacles

• touch with wet hands

• Close the lid when not in use. If this outlet is mishandled, it may cause an electric shock and failure.

POWER OUTLETS

• Two 12 Volt (13 Amp) power outlets are located on the lower instrument panel, below the open storage bin. The driverside power outlet is controlled by the ignition switch and the passenger-side power outlet is connected directly to the battery. The driver-side power outlet will also operate a conventional cigar lighter unit (if equipped with an optional Smoker's Package).

• One outlet in the removable floor console (if equipped) shares a fuse with the lower outlet in the instrument panel and is also connected to the battery. Do not exceed a maximum power of 160 Watts (13 Amps) shared between the lower panel outlet and the removable floor console outlet.

• On vehicles equipped with the Super Console the power outlets are located under the retractable cover.To access the power outlets push down on the cover and slide it toward the instrument panel.

• The outlet in the rear quarter panel near the liftgate and the upper outlet in the instrument panel are both controlled by the ignition switch. Each of these outlets can support 160 Watts (13 Amps). Do not exceed 160 Watts (13 Amps) for each of these outlets.

Page 79

ELECTRONICS

NOTE:

• Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded, the fuse protecting the system will need to be replaced.

• Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your new vehicle warranty.

Page 80

UTILITY

IN-FLOOR STORAGE – STOW'N GO®

Second Row Seat Storage Bins

• Storage bins are located in the floor in front of the second row seats that can be used when the second row seat is in the upright position. Pull up on the storage bin latch to open the cover. Slide the storage bin locking mechanism to the "Lock" position to allow greater access to the storage bin.

Cargo Area Storage

• The liftgate sill plate has a raised line with the statement “Load To This Line”. This line indicates how far rearward cargo can be placed without interfering with liftgate closing.

WARNING!

In a collision, serious injury could result if the seat storage bin covers are not properly latched. Do not drive the vehicle with the storage bin covers open. Keep the storage bin covers closed and latched while the vehicle is in motion. Do not use a storage bin latch as a tie down.

ROOF LUGGAGE RACK

•

The crossbars on your vehicle are delivered stowed within the roof rack side rails. When installed, the roof rack can hold a maximum of 150 lbs (68 kg) of evenly distributed weight.

Installing The Crossbars

To install the crossbars, completely loosen

• the thumb screws at both ends and lift the crossbar from its stowed position.

• Bend the pivot points at each end of the crossbar and slide the thumb screw down.

• Set the crossbars into position and tighten the thumb screws.

NOTE:

Make sure the directional arrow on the crossbar aligns with the directional arrow on the side rail.

• Refer to the Owner's Manual on the DVD for further details.

Page 81

UTILITY

TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS)

Engine/

Transmission

3.6L/Automatic

* For vehicles equipped with Fold-in-Floor seating, the Gross Trailer Weight must be reduced

by 100 lbs (45 kg). Refer to local laws for maximum trailer towing speeds.

NOTE: The trailer tongue weight must be considered as part of the combined weight of

occupants and cargo, and should never exceed the weight referenced on the Tire and

GCWR (Gross

Combined

Wt. Rating)

8,750 lbs

(3,969 kg)

8,750 lbs

(3,969 kg)

8,750 lbs

(3,969 kg)

Loading Information placard.

Frontal Area

40 sq ft

(3.72 sq m)

40 sq ft

(3.72 sq m)

40 sq ft

(3.72 sq m)

Max. GTW

(Gross Trailer Wt.)

Up to 2 persons &

Luggage 3,600 lbs

(1,633 kg) *

3 to 5 persons &

Luggage 3,350 lbs

(1,519 kg) *

6 to 7 persons &

Luggage 3,000 lbs

(1,360 kg) *

Max.

Tongue Wt.

360 lbs (163 kg)

335 lbs (152 kg)

300 lbs (136 kg)

RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.)

Towing Condition Wheels OFF the Ground All Models

Flat Tow NONE

Dolly Tow

On Trailer ALL OK

Front OK

Rear

NOT ALLOWED

Page 82

WHAT TO DO IN EMERGENCIES

ROADSIDE ASSISTANCE

•

Dial toll-free 1-800-521-2779 for U.S. Residents or 1-800-363-4869 for Canadian Residents.

•

Provide your name, vehicle identification number, license plate number, and your location, including the telephone number from which you are calling.

• Briefly describe the nature of the problem and answer a few simple questions. You will be given the name of the service provider and an estimated time of arrival. If you feel

• you are in an “unsafe situation”, please let us know. With your consent, we will contact local police or safety authorities.

INSTRUMENT CLUSTER WARNING LIGHTS

- Electronic Stability Control (ESC) Indicator Light

• If this indicator light flashes during acceleration, apply as little throttle as possible. While driving, ease up on the accelerator. Adapt your speed and driving to the prevailing road conditions. To improve the vehicle's traction when starting off in deep snow, sand or gravel, it may be desirable to switch the ESC system off.

- Tire Pressure Monitoring System ( TPMS) Light

• Each tire, including the spare (if provided), should be checked monthly, when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.)

• As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.

• IF THE LIGHT STARTS FLASHING INDICATING A LOW TIRE PRESSURE, ADJUST THE

AIR PRESSURE IN THE LOW TIRE TO THE AIR PRESSURE SHOWN ON THE VEHICLE PLACARD OR TIRE INFLATION PRESSURE LABEL LOCATED ON THE DRIVER'S DOOR.

NOTE:

AFTER INFLATION, THE VEHICLE MAY NEED TO BE DRIVEN FOR 20 MINUTES BEFORE THE FLASHING LIGHT WILL TURN OFF.

• Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.

Page 83

WHAT TO DO IN EMERGENCIES

•

Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue each time the vehicle is restarted as long as the malfunction exists.

•

When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.

NOTE:

Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the Winter. Example: If garage temperature is 68°F (20°C) and the outside temperature is 32°F (0°C), then the cold tire inflation pressure should be increased by 3 psi (21kPa),which equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition.

CAUTION!

The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can, or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.

- Engine Temperature Warning Light

• This light warns of an overheated engine condition.

• If the light turns on or flashes continuously while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRALand idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service.

• Werecommendthat you do not operate the vehicle or engine damage will occur.Havethe vehicle serviced immediately.

WARNING!

A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats.

Page 84

WHAT TO DO IN EMERGENCIES

BRAKE

• The Brake Warning light illuminates when there is either a system malfunction or the parking brake is applied. If the light is on and the parking brake is not applied, it indicates a possible brake hydraulic malfunction, brake booster problem or an Anti-Lock Brake System problem.

• Please have your vehicle serviced immediately.

- Brake Warning Light

WARNING!

Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately.

- Malfunction Indicator Light (MIL)

• Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the MIL after engine start. The vehicle should be serviced if the light stays on through several t ypical driving cycles. In most situations, the vehicle will drive normally and not require towing.

• If the MIL flashes when the engine is running, serious conditions may exist that could lead to immediate loss of power or severe catalytic converter damage. We recommend you do not operate the vehicle. Have the vehicle serviced immediately.

- Electronic Stability Control (ESC) OFF Indicator Light

• This light indicates the Electronic Stability Control (ESC) is off.

- Charging System Light

•

This light shows the status of the electrical charging system. If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system.

• We recommend you do not continue driving if the charging system light is on. Have the vehicle serviced immediately.

- Oil Pressure Warning Light

•

This light indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on.

• We recommend you do not operate the vehicle or engine damage will occur. Have the vehicle serviced immediately.

- Anti-Lock Brake (ABS) Light

• This light monitors the Anti-Lock Brake System (ABS).

• If the light is not on during starting, stays on, or turns on while driving, we recommend you drive to the nearest authorized dealer immediately and have the vehicle serviced immediately.

Page 85

WHAT TO DO IN EMERGENCIES

- Electronic Throttle Control (ETC) Indicator Light

• This light informs you of a problem with the system.

• If a problem is detected, the light will come on while the engine is running. Cycle the ignition when the vehicle has completely stopped and the shift lever is placed in the PARK position; the light should turn off.

• If the light remains lit with the engine running, your vehicle will usually be drivable; however, see an authorized dealer immediately. If the light is flashing when the engine is running, immediate service is required and you may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing.

- Air Bag Warning Light

• If the light is not on during starting, stays on, or turns on while driving, have the vehicle serviced by an authorized dealer immediately.

Fuel Cap/Loose Gas Cap Message

• If a “gas cap” message (shown as gASCAP) appears, tighten the gas cap until a “clicking” sound is heard.

• Press the odometer reset button, located below the tachometer, to turn the message off.

• If the message continues to appear for more than three days after tightening the gas cap, see your authorized service center.

“CHANGE OIL” MESSAGE

• If a “Change Oil” message appears and a single chime sounds, it is time for your next required oil change.

Resetting The Light After Servicing

Vehicles Equipped With Keyless Enter-N-Go™

• Without pressing the brake pedal, push the ENGINE START/STOP button and cycle the ignition to the ON/RUN position (Do not start the engine.)

• Fully depress the accelerator pedal, slowly, three times within 10 seconds.

• Without pressing the brake pedal, push the ENGINE START/STOP button once to return the ignition to the OFF/LOCK position.

Vehicles Not Equipped With Keyless Enter-N-Go™

• Turn the ignition switch to the ON/RUN position (Do not start the engine.)

• Fully depress the accelerator pedal, slowly, three times within 10 seconds.

• Turn the ignition switch to the OFF/LOCK position.

NOTE:

If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure.

Page 86

WHAT TO DO IN EMERGENCIES

IF YOUR ENGINE OVERHEATS

• In any of the following situations, you can reduce the potential for overheating by taking the appropriate action.

• On the highways — slow down.

• In city traffic — while stopped, place the transmission in NEUTRAL, but do not increase engine idle speed.

NOTE:

There are steps that you can take to slow down an impending overheat condition:

• If your air conditioner (A/C) is on, turn it off. The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.

• You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.

CAUTION!

Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT (H), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on HOT (H), and you hear continuous chimes, turn the engine off immediately, and call for service.

WARNING!

You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.

Page 87

WHAT TO DO IN EMERGENCIES

JACKING AND TIRE CHANGING

Jack Location

• The jack, jack handle and winch handle tools are stowed behind the rear left side trim panel in the rear cargo area. Turn the two cover latches to release the cover.

• Remove the pouch containing the scissors jack, jack handle, and tools.

Spare Tire Removal

• The spare tire is stowed inside a protective cover located under the center of the vehicle between the front doors by means of a cable winch mechanism. The “spare tire drive” nut is located on the floor,under a plastic cap at the front of the floor console or under front super console forward bin liner.

To Access Spare Tire Winch Drive Nut

• To access the spare tire winch drive nut and lower the spare tire, you will need to refer to one of the following center console configurations.

Super Console

• For vehicles equipped with the Super Console, the spare tire winch assembly drive nut is located beneath the console.

1. Pull the lower drawer out from the rear of the floor console.

Page 88

WHAT TO DO IN EMERGENCIES

2. Open the front drawer to expose the storage compartment.

3. Remove the liner from the console's storage compartment to access the spare tire winch drive nut.

Premium/Base/Cargo Center Console

• Pull the Winch Cover assembly plug (if equipped) to access the winch drive nut.

Page 89

WHAT TO DO IN EMERGENCIES

Spare Tire Tools

• The tool pouch contains three pieces and can be assembled into a spare tire hook; to remove the compact spare tire/cover assembly from under the vehicle, or a Winch T-handle; to raise/lower the compact spare tire/cover assembly.

Assembled T-handle

A - Spare Tire Hook/T-handle B - Extension 1 C - Extension 2

Assembling The Spare Tire Hook

A - Spare Tire Hook/T-handle B - Extension 1 C - Extension 2

Page 90

WHAT TO DO IN EMERGENCIES

Spare Tire Removal Instructions

• The spare tire is located under the vehicle beneath the center console area.

1. Assemble the spare tire tools into a T-handle and place the square end over the spare tire winch drive nut.

2. Rotate the nut to the left until the winch

mechanism stops turning freely. This will allow enough slack in the cable to allow you to pull the spare tire out from underneath the vehicle.

3. Assemble the winch handle extensions

to form the spare tire hook, and pull the spare tire from under the vehicle.

NOTE:

If either front tire is flat it may be necessary to jack up the vehicle to removethe compact spare tire/cover assembly from under the vehicle.

4. Stand the tire/cover assembly upright

and remove the wheel spacer by squeezing the winch retaining tabs together. Push the retainer through the spare tire to release it from the wheel.

Page 91

WHAT TO DO IN EMERGENCIES

Preparations For Jacking

1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas.

2. Turn on the Hazard Warning flasher.

3. Set the parking brake.

4. Place the shift lever into PARK.

5. Turn OFF the ignition.

NOTE:

Passengers should not remain in the vehicle when the vehicle is being jacked.

• Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel.

Jacking Instructions

1. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground.

Page 92

WHAT TO DO IN EMERGENCIES

2. There are two jack engagement locations on each side of the vehicle body. These locations are on the sill flange of the vehicle body.

Rear jack locations are between a pair of down-facing tabs on the sill flange of the vehicle side body.

Front jack location is on the sill flange of the vehicle body and is located 6 in (150 mm) from door edge.

NOTE:

In some situations the jack may need to be placed on its side in order to be pushed under the vehicle. Return the jack to its correct orientation once it is under the vehicle.

Page 93

WHAT TO DO IN EMERGENCIES

3. Place the wrench on the jack screw and turn to the right until the jack head is properly engaged in the described location. Do not raise the vehicle until you are sure the jack

is securely engaged.

4. Raise the vehicle by turning the jack screw to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability.

5. Remove the wheel lug nuts, for vehicles with wheel covers, remove the cover from the wheel by hand. Do not pry the wheel cover off. Then pull the wheel off the hub.

6. Install the compact spare tire. Lightly tighten the lug nuts.

NOTE:

• Do not install the wheel cover on the compact spare.

• Do not use a hammer or force to install the wheel covers.

7. Lower the vehicle by turning the jack screw to the left.

8. Finish tightening the lug nuts. Push down

on the wrench while at the end of the handle for increased leverage. Tighten the lug nuts in a star pattern until each nut has been tightened twice. The correct wheel nut tightness is 102 ft lbs (138 N·m). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station.

9. Lower the jack to its fully-closed position.

10. Place the deflated (flat) tire and compact spare tire cover assembly in the rear cargo

area. Do not stow the deflated tire in the spare tire location. Have the full-sized tire repaired or replaced, as soon as possible.

11. Stow the cable and wheel spacer before driving the vehicle. Reassemble the winch

handle extensions to form a “T” and fit the winch T-handle over the drive nut. Rotate the nut to the right until the winch mechanism clicks at least three times.

NOTE:

Refer to the “Spare Tire Tools” section for instructions on assembling the T-handle.

12. Stow the jack, jack handle and winch handle tools back in the stowage compartment.

13. Check the compact spare tire pressure as soon as possible. Correct the tire pressure, as

required.

Page 94

WHAT TO DO IN EMERGENCIES

Securing The Spare Tire

1. Assemble the winch handle extensions to form a T-handle and fit the winch T-handleover the drive nut. Rotate the nut to the left until the winch mechanism stops turning freely. This will allow enough slack in the cable to allow you to pull the wheel spacer out from under the vehicle.

2. Assemble the winch handle extensions to form the spare tire hook, and pull the wheel

spacer from under the vehicle.

3. Turn the compact spare tire so that the valve stem is down, and place the tire into the

spare tire/cover assembly. Slide the wheel spacer through the center of the wheel and spare tire/cover assembly, so that the two retainer tabs snap out and engage the spare tire cover on the opposite side.

4. Using the winch T-handle, rotate the drive nut to the right until the compact spare

tire/cover assembly is drawn into place against the underside of the vehicle.

5. Continue to rotate the nut to the right until you hear the winch mechanism click three

times. It cannot be overtightened. Check under the vehicle to ensure the compact spare tire/cover assembly is positioned correctly against the underside of the vehicle.

Road Tire Installation

Vehicles Equipped With Wheel Covers

1. Mount the road tire on the axle.

2. To ease the installation process for steel wheels with wheel covers, install two lug nuts

on the mounting studs which are on each side of the valve stem. Install the lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts.

3. Align the valve notch in the wheel cover

with the valve stem on the wheel. Install the cover by hand, snapping the cover over the two lug nuts. Do not use a hammer or excessive force to install the cover.

4. Install the remaining lug nuts with the

cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts.

5. Lower the vehicle to the ground by turn-

ing the jack handle counterclockwise.

1 — Valve Stem 4 — Wheel Cover 2 — Valve Notch 5 — Mounting Stud 3 — Wheel Lug Nut

Page 95

WHAT TO DO IN EMERGENCIES

6. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the lug nuts in a star pattern until each nut has been tightened twice. The correct tightness of each lug nut is 102 ft/lbs (138 N·m). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or service station.

7. After 25 miles (40 km) check the lug nut torque with a torque wrench to ensure that all lug

nuts are properly seated against the wheel.

Vehicles Without Wheel Covers

1. Mount the road tire on the axle.

2. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts.

3. Lower the vehicle to the ground by turning the jack handle counterclockwise.

4. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the lug nuts in a star pattern until each nut has been tightened twice. The correct tightness of each lug nut is 102 ft/lbs (138 N·m). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or service station.

5. After 25 miles (40 km) check the lug nut torque with a torque wrench to ensure that all lug nuts are properly seated against the wheel.

CAUTION!

• The winch mechanism is designed for use with the winch T-handle only. Use of air wrench or other power tools is not recommended and can damage the winch.

• Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle.

• Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the spare tire is mounted incorrectly.

• The compact spare tire/cover assembly must be used when the compact spare tire is stored. Failure to use this cover could drastically reduce the life of the compact spare tire.

• The winch mechanism is designed specifically to stow a compact spare tire only. Do not attempt to use the winch to stow the full size flat tire, or any other full-size tire. Vehicle damage may result.

Page 96

WHAT TO DO IN EMERGENCIES

WARNING!

• Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.

• Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you.You could be crushed. Never put any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.

• Never start or run the engine while the vehicle is on a jack.

• The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for servicepurposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas.

• Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle:

• Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.

• Turn on the Hazard Warning flasher.

• Block the wheel diagonally opposite the wheel to be raised.

• Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE.

• Do not let anyone sit in the vehicle when it is on a jack.

• Do not get under the vehicle when it is on a jack.

• Only use the jack in the positions indicated and for lifting this vehicle during a tire change.

• If working on or near a roadway, be extremely careful of motor traffic.

• To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground.

• Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire.

• Toavoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury.

• A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately.

• Verify that both retainer tabs of the wheel spacer have been properly extended through the center of the wheel and spare tire/cover assembly. Failure to properly engage both retainer tabs could result in loss of the spare tire and cover assembly, which will cause vehicle damage and may cause loss of vehicle control.

Page 97

WHAT TO DO IN EMERGENCIES

JUMP-STARTING

• If your vehicle has a discharged battery it can be jump-started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack.

• Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully.

NOTE:

When using a portable battery booster pack follow the manufacturer’s operating instructions and precautions.

Preparations for Jump-Start

• The battery in your vehicle is located on the left side of the engine compartment.

• Set the parking brake, shift the automatic transmission into PARK and turn the ignition to LOCK.

• Turn off the heater, radio, and all unnecessary electrical accessories.

• If using another vehicle to jump- start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF.

Jump-Starting Procedure

• Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged

vehicle.

• Connect the opposite end of the positive (+) jumper cable to the positive (+) post of the

booster battery.

• Connect the negative end (-) of the jumper cable to the negative (-) post of the booster

battery.

• Connect the opposite end of the negative (-) jumper cable to a good engine ground

(exposed metal part of the discharged vehicle's engine) away from the battery and fuel injection system.

• Start the engine in the vehicle that has the booster battery, let the engine idle a few

minutes, and then start the engine in the vehicle with the discharged battery.

Once the engine is started, remove the jumper cables in the reverse sequence:

• Disconnect the negative (-) jumper cable from the negative (-) post of the vehicle with the discharged battery.

• Disconnect the negative end (-) of the jumper cable from the negative (-) post of the booster battery.

Page 98

WHAT TO DO IN EMERGENCIES

• Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery.

• Disconnect the positive (+) end of the jumper cable from the positive (+) post of the discharged vehicle.

• If frequent jump-starting is required to start your vehicle you should have the battery and charging system inspected at your authorized dealer.

CAUTION!

• Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur.

• Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle.

• Accessories that can be plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.

WARNING!

• When temperatures are below the freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode and cause personal injury. Battery temperature must be brought above freezing point before attempting a jump-start.

• Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades.

• Remove any metal jewelry, such as watch bands or bracelets, that might make an inadvertent electrical contact. You could be severely injured.

• Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive. Keep open flames or sparks away from the battery.

• Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.

• Failure to follow this procedure could result in personal injury or property damage due to battery explosion.

• Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury.

Page 99

WHAT TO DO IN EMERGENCIES

SHIFT LEVER OVERRIDE

• If a malfunction occurs and the shift lever cannot be moved out of the PARK position, you can use the following procedure to temporarily move the shift lever:

To access the shift lever override, remove

• the cover located to the top right of the shift lever in the instrument panel.

• Firmly set the parking brake.

• Turn the ignition switch to the ACC or ON position without startingthe engine.

• Press and maintain firm pressure on the brake pedal.

• The override can be activated by pressing the white-colored tab, which can be accessed through the hole in the instrument panel.

• Move the shift lever into the NEUTRAL position.

• The vehicle may then be started in NEUTRAL.

• Reinstall the override cover.

TOWING A DISABLED VEHICLE

Towing Condition Wheels OFF the Ground ALL MODELS

Flat Tow NONE

Wheel lift

Flatbed

Rear

Front OK

ALL BEST METHOD

If transmission is operable:

• Transmission in NEUTRAL

•

25 mph (40 km/h) max speed

•

15 miles (24 km) max distance

Page 100

WHAT TO DO IN EMERGENCIES

FREEING A STUCK VEHICLE

• If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between DRIVE and REVERSE while gently pressing the accelerator. Use the least amount of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels or racing the engine.

NOTE:

Press the "ESC Off" switch, to place the Electronic Stability Control (ESC) system in "Partial Off" mode before rocking the vehicle. Once the vehicle has been freed, press the "ESC Off" switch again to restore "ESC On" mode.

CAUTION!

• When “rocking” a stuck vehicle by moving between REVERSE and DRIVE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.

• Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring).

WARNING!

Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle's wheels faster than 30 mph (48 km/h) when you are stuck. Do not let anyone near a spinning wheel, no matter what the speed.

Dodge 2013 Grand Caravan User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual