£j:i'-; , ,,"
SO-O216A-xxx SERIES 118127X
DODGEDURANGO
OVERHEAD CONSOLE for use with FLIPDOWN VIDEO SYSTEM
~
~
i
j
~
f I
~ I
;
OPTIONAL ACCESSORIES MA y BE ADED:
ESCORT PASSPORT 4600 RADAR DETECTOR
1
MINI- TRIP COMPUTER FROM O.E.M. OVERHEAD
2
These instructions are intended for use only by experienced professionals in the automotive
customizing business. Special tools and equipment, as well as specialized handling and care
of product during installation, may be required. Before beginning this installation, carefully
read through the following instructions. Use extreme care when cutting headliner material.
Check for wiring or other componentry above headliner material. Cut only where indicated.
Materials/ Tools required for this installation:
I. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter
3. 1/8" drill bit 4. ~" hex socket bit
5; Razor knife or similar 6. A wl or similar tool
7. Audiovox Series 640/641 Video Module
,
FOR USE IN VEHICLES EQUIPPED WITH FACTORY INSTALLED
REAR AIR CONDITIONING ONL Y.
~
INSTALLATION I;,\,STRUCTION # 44-0021A
Apr.13,1998
Printed in the U.S.A
MA TERIALS PROVIDED FOR INST ALLA TION
..;!~",;;c..c;, ..
1
2
3
4
5
6
7
8
9
10
11
SCREW, # 6 X Y2 PPH 13
SCREW,#8X* HWH 6
SCREW, # 8 X 11/4 PWH 2
FRONT MOUNTING BRACKET 1
COMPUTER MOUNTING BRACKET I
REAR MOUNTING BRACKET I
RADAR DETECTOR HOUSING I
BLOCK OFF I
CONSOLE I
FRONT LIGHT I
FRONT LIGHT TRIM I
,gTYlrEMi~,pe~cription
[
~
~
.
.
i
{
I
.
,~;.:~~':~,;;
" ,,-';;;c.:,;
1
~.
~!
t
2
3
"
8
5
~
4
D
9
c
~
;.
s
I!:
l
i.
i
~
INSTALLATION INSTRUCTION # 44-0021A
11
10
7
Apr. 13, 1998
Printed in the U.S.A.
2
.""4.'
I. PREPARATION OF VEHICLE INTERIOR
,;;::.:!~emoveand discard fr.on(dOln~ light and
proceed to step 7.
2. Remove front mounting screw from overhead
console and slide forward to release tabs at rear
of console. See figure 1.
..
~
({
~
$
"'
~
*
;t
~
,;
,J:
if.
,
0
I
/
/
FIGURE 1
3. Disconnect wiring harness from console. See fig. 2
4. Individually cut and remove the green, white,
and black wires that control the map lights
from the connector on the mini-trip computer.
5. Remove and discard (4) four screws which
secure the mini-trip computer to console.
Retain computer and bezel for use later.
6. Remove and discard (4) four screws which
secure brace to roof of vehicle. Discard brace.
See figure 2.
.
.
~
-
-\:
FIGLTRE 2
,
~
~
2
.
.
t
I
~
~
f
f
i
I
[
I
!
7. Carefully trim headliner as shown and install front
mounting bracket (item 4 pg 2). Secure using (2)
two #8 x ~" screws (item 2 pg 2) in dimples in
roof brace. See figure 3. Caution: Before cutting
v
~
headliner material, check for wiring or other
componentry above headliner. Cut only where
indicated.
FIGURE 3
3
~
7"
T
~"
-~~:i"
~ ~5rf:;~tC .","
~",,~' ,~~
8. Carefully trim headliner and drill (2) two Y2"
holes in return air grille to allow for screws to
pass through when mounting bracket. See fig. 4.
FIGURE 4
9. Install rear mounting bracket (item 6 pg 2) and
secure using (4) four # 8 x 3,{" screws (item 2
pg 2). Make sure that holes in bracket align
with dimples in roof brace. See figure 5.
II. PREPARATION OF CONSOLE FOR INSTALLATION
T 1
t~
'--"-
FIGURE 5
.f
~
~
f
ii
;:
L
W
~ ~
10. Install the video system in console and secure
~.
,\
using hardware supplied with video system.
Start all screws before tightening. Be~n with
the rear center screw, then alternately tighten
screws around the perimeter of pod. See figure
6. Refer to owner's manual supplied with
video system. Caution: Do not overtighten
screws.
FIGURE 6
~
, I
4
11. Install fro~,tjig4t(item 10 pg 2) and secure
,-,,"= , "'"
-using (3) three::~~6;;kV2" screws {item 1 pg'2)..
Install front light trim (item II pg 2) around
light. See figure 7.
\
I
i
t
';;
,.
i{
:'i
~;
bI;:
;,
".
:!
i
;}
~
.
FIGURE 8
.
12. There are 3 options available for the front of the
console. For no accessory see step A. For radar
detector housing see step B. For O.E.M. minitrip computer see step C.
A. Install block off (item 8 pg 2) and secure
using (4) four # 6 x ,Y2" screws. See fig. 8.
.,
Install Escort Passport 4600 radar detector
B.
housing (item 7 pg 2) and secure using (4) four
# 6x Y2" screws (item 1 pg 2). See figure 9.
FIGLRE 9
c. Install O.E.M. mini-trip computer bezel from
the backside of opening in console.
Install computer mounting bracket (item 5 pg 2)
and secure using (2) two # 6 x Y2" screws (item
1 pg 2). See figure 10.
if
~~
~
.;
~
'I'
ii
"
~
ii
.if
9
fj
ij
~
.
.n
FIGURE 10
Install O.E.M. mini-trip computer and secure
using (4) four #6 x 1f2" screws (item I pg 2).
See figure 11. Do not overtighten screws.
6
FIGURE 11
III. INST ALLA TION OF CONSOLE
" " " .
NOTE: Additional a"ssistance in mounting the overhead console in vehicle is
advised to prevent damage to console or components.
13. Install and route all accessory wiring, video
and audio cables, and any other added
component requirements to their respective
places in the vehicle. Refer to component
installation instructions for wiring diagrams.
The suggested routing of the video system
cable is as follows: Above the headliner from
video system to B-pillar. Down the B-pillar
to the floor. Route the power lead to an
accessory controlled source. Connect the
ground lead to the vehicle chassis. Route the
remaining wiring (RCA plugs, Remote
Sensor extension, etc.) to the VCP location.
See figure 12. Connect per instructions
included with the video system. Ifvideo
system if to be used as a television, install an
appropriate antenna per instructions included
with the antenna.
c
Figure 12
f
~
:;:
...
~
'.
~
~
rf
~-
J
;t
~
r.
t
f
14. Raise console into approximate position and
connect all wiring to components. Connect
wiring aI)d cabling to video system per
instructions included with \'ideo system.
15. Check function of all components and lights.
See operating instructions for video system
operations check. For further assistance, refer
to the video system manual for the technical
support phone number listed for your area.
16. Carefully position console against headliner.
Release video screen from locked position.
Lower video screen to viewing position for
access to mounting locations in top of video
system housing and align holes in housing
with holes in rear mounting bracket. Secure
using (4) four # 6 x Y2" screws (item 1 pg 2).
Figure 13
Caution: Do not overtighten screws. Use extra support for the console until secured to the
vehicle. Failure to do so may cause damage to console or installed components.
See figure 13.
0;
ii
.
"'
#. .
.
17. Using an awl or similar tool, align the front
mounting holes in console with holes in bracket.
Secure using (2) two # 8 x 1 ~" screws (item 3
pg 2). See figure 14.
Caution: Do not overtighten screws.
"'
.r
I.
~
~
j
~
~
'f
:f
~
o
:.:
~,
Figure 14
.
}
.
.
,
il
);
8
Loading...