Docomo Style P-06A Instruction Manual

Download

P-06A

ISSUE DATE:

NAME:

PHONE NUMBER:

MAIL ADDRESS:

INSTRUCTION MANUAL

‘09.3

Easy Search/Contents/Precautions

Before Using the Handset

Voice/Videophone Calls

Phonebook

Sound/Screen/Light Settings

Security Settings

Camera

i-mode/i-motion/i-Channel

Mail

i-αppli

Osaifu-Keitai/ToruCa

1Seg

Full Browser

Data Management

Music

Convenient Functions

Character Entry

Network Services

PC Connection

Overseas Use

Appendix/Troubleshooting

Index/Quick Manual

DOCOMO W-CDMA System

Thank you for selecting the “docomo STYLE series P-06A”.

Before or during use of the P-06A, make sure that you read this manual and the separate manuals for other optional devices thoroughly so that you can use the P-06A correctly. If you feel any inconvenience in reading the manual, contact the docomo Information Center listed on the back page of this manual. The P-06A is designed to be your close partner. Treat it carefully at all times to ensure long-term performance.

●Because the FOMA phones use radio waves, they cannot be used in places

where radio waves do not reach, such as inside tunnels, underground, or in buildings; or the outside where radio waves are weak or out of the FOMA service area. They may not be used in the high-rise buildings even when the antennas are unobstructed. You may also experience interruption of calls even when using without moving while the radio waves are strong enough for the three antennas to appear on the display.

●Use the FOMA phone carefully to avoid disturbing other people when in

public, or in crowded or quiet places.

●Since the FOMA phones use radio waves as the medium of

telecommunication, calls may be tapped by the third party. However, the W-CDMA system automatically supports tapping prevention, so your conversation will be incomprehensible to the third party.

●The FOMA phones change your voice into digital signals and send them to

the other party. In places where the radio waves are weak, the digital signals may not be converted correctly, and in such a case, the voice may sound different from the actual original voice. The user hereby agrees that the user shall be solely responsible for the result

●

of the use of SSL. Neither DOCOMO nor the certifiers as listed herein make any representation and warranty as for the security in the use of SSL. In the event that the user shall sustain damage or loss due to the use of SSL, neither DOCOMO nor the certifiers shall be responsible for any such damage or loss. Certifiers: VeriSign Japan K.K., Cybertrust Japan Co., Ltd., GlobalSign K.K.,

●This FOMA phone supports FOMA Plus-Area and FOMA High-Speed Area.

●The FOMA terminal can be used only via the FOMA network provided by

DOCOMO and in DOCOMO’s roaming area.

Before using your FOMA phone

RSA Security Japan Ltd., SECOM Trust Systems Co., Ltd., and Comodo CA Ltd.

●It is recommended that you make separate notes of the information (such as

Phonebook entries, schedule events, text memos, record messages, voice memos, movie memos) stored in the FOMA phone and keep them in a safe place. Note that we cannot be held responsible for the unlikely event of loss of the stored contents due to a malfunction, repair, change of your model, or other mishandling of the FOMA phone.

●You are advised to save your important data files to the microSD card. If you

have a personal computer, you can transfer and save the information such as Phonebook entries, mail messages, schedule events, and others to the personal computer by using DOCOMO keitai datalink.

For Using This Manual

This FOMA phone supports Kisekae Tool (page 104). If you use Kisekae Tool to change the design of the Menu display, some menu configurations change according to the usage frequency depending on the type of the menu. Further, some menu numbers that are assigned to the menu items do not apply.

You can download the latest information about this manual from the following DOCOMO website:

・User’s Manual (PDF file) Download

(http://www.nttdocomo.co.jp/english/support/manual/index.html)

※The URL and the content of the website might be modified

without notice.

Easy Search/Contents/Precautions

How to Read/Refer to This Manual

In this manual, illustrations and symbols are used in the explanations so that you can correctly and easily use the FOMA phone.

pThe operating procedures and displays in this manual are described with the default

settings of the “White” handset mainly. However, the following settings are changed.

・“Display setting” → “Stand-by display”: OFF ・“Display setting” → “Clock” → “Position”: Pattern 2 ・“Character size” → “Set at one time”: Extra large ・“Menu icon setting”: Sign menu

pDisplays and illustrations described in this manual are for reference. The actual ones

might differ.

pIn this manual, “Osaifu-Keitai compatible i-αppli which supports the IC card function” is

described as “Osaifu-Keitai compatible i-αppli”.

pNote that “P-06A” is referred to as “FOMA phone” in this manual. pIn the operating procedures of this manual, key operations are described with

simplified key icons.

pThe icons such as “ ”, “ ”, and“ ” which appear by the default setting are

described as “ ”, “ ”, and “ ” in the text.

pThe functions which use a microSD card are described in this manual; however, you

need to obtain a microSD card separately to make these functions available. See page 314 for the microSD card.

How to Refer to This Manual

By the following search methods, you can find pages where your desired functions and services are described:

From the Index

Search from the index when you know the names of functions or services.

From Easy Search

Search from keywords for the functions you frequently use or the functions that are convenient if you can know any.

From the Tabs on the Cover

Search from the tabs printed on the cover.

From the Contents 

Search from the contents that categorize functions.

From the Main Functions

Search from here to use the main functions.

From the Function List 

Search from the function list.

From Quick Manual 

Quick Manual gives you a clear, brief description about basic functions. You can take it when you go out. Further, Quick Manual “For Overseas Use” is attached, so refer to it when you use the FOMA phone overseas.



P.6

P.8

P.426

P.502

See the next page for details.

Easy Search/Contents/Precautions

It is prohibited to copy all or part of this manual without permission. The instructions contained in this manual may be changed without notice.

How to search for “Alarm” is explained here as an example of search method.

From the Index

P.494

Search for a function or a service name as shown on the right.

From Easy Search

P.4

Easy Search/Contents/Precautions

Search for the function you frequently use or that is convenient if you know any as shown on the right.

From the Tabs on the Cover

Cover page

Search for the function you want to set in the order of “Cover”

→ “First page of Chapter” → “Description page” as shown

on the right.

i-αppli

Osaifu-Keitai/ToruCa

Full Browser

Data Management

Music

Convenient Functions

Character Entry

Network Services

PC Connection

Overseas Use

Appendix/Troubleshooting

Index/Quick Manual

Additional service . . . . . . . . . . . . . .406

Additional guidance. . . . . . . . . . .407

Address link function . . . . . . . . . . .169

Alarm . . . . . . . . . . . . . . . . . . . . . . .360

Alarm setting. . . . . . . . . . . . . . . . . . 368

Answer setting . . . . . . . . . . . . . . . . .64

Other things you can do

To reduce the battery consumption.............................. <Power Saver Mode> 101

To scan QR codes or bar codes...................................... <Bar Code Reader> 146

To use the microSD card...................................................... <microSD Card> 314

To exchange information using infrared rays.........<Infrared Data Exchange> 326

To listen to music.................................................................. <MUSIC Player> 344

To use the FOMA phone as an alarm clock .......................................<Alarm> 360

To use the FOMA phone as a calculator..................................... <Calculator> 373

To use the FOMA phone overseas...........................<International Roaming> 416

To update software programs........................................... <Software Update> 474

To update security......................................................... <Scanning Function> 479

1Seg

Multitask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Multitask> 357

Informing You of an Incoming Call/Mail Message by Voice

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Reading Aloud> 358

Turning Power On/Off Automatically at a Specified Time

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Auto Power ON/OFF> 360

Using Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Alarm> 360

Using Calendar to Manage Schedule . . . . . . . . . . .<Schedule> 363

Using ToDo to Manage Schedule . . . . . . . . . . . . . . . . . <ToDo> 367

Setting Operating Conditions of Alarm . . . . . <Alarm Setting> 368

Go to page 360 where “Alarm” is explained.

Function name You can find this in Index.

<Alarm>

Using Alarm

You can set Alarm to alert you at the specified time with an alarm tone,

Operating procedure (See page 32)

Reference display (Characters and settings are for reference.)

Chapter title

You can search by chapter.

Options and their explanations

animation and illumination. You can store up to 12 alarms.

Alarm You can set whether to validate or invalidate the alarm.

Time Enter the time for sounding the alarm.

Tone Select a type of alarm toneSelect a folder

Volume Use Bo to adjust the volume.

Convenient Functions

Prefer manner

mode

360

mStationeryAlarmHighlight an alarm and press l()

Do the following operations.

Item Operation/Explanation

ON or OFF

pYou cannot set the same time as the time set for the stored

alarm.

Select an alarm tone.

pIf you set “Step”, the alarm tone is silent for about three

seconds, and then the volume steps up every about three seconds, from Level 1 through Level 6.

You can set the alarm tone which sounds at the specified time during Manner Mode.

ON or OFF

ON. . . . . Soundsat the same volume as set for “Alarm volume”.

OFF. . . . Sounds at the volume set for this function.

Press l().

Menu number (See page 34)

+m-4-4

Function Menu while Alarm is Displayed

Function menu Operation/Explanation

Edit Go to step 1 of “Using Alarm” on page 360.

Detail You can display the stored alarm contents.

Set this You can validate the stored alarm.

Set all You can validate all the stored alarm.

Delete (Delete this)

Delete (Delete all)

Information

pDuring a call, the alarm tone sounds at the level set for “Volume” (earpiece volume). pWhen you set the power to automatically turn on and an alarm to sound, the default

alarm tone sounds if the alarm with the UIM security is selected.

pTurn off the FOMA phone after setting “Auto power ON” to “OFF” when youare near

electronic devices using high-precision control or weak signals, or where the use is prohibited such as in airplanes and hospitals.

When you set an alarm for “Alarm”, “Schedule”, and “ToDo”

The icon appears on the desktop.

“” . . . Displayed when an alarm is set for today (except the setting for past time).

“” . . . Displayed when an alarm isset for tomorrow or onward only.

pIf you set “Alarm” of a schedule event/ToDo item to “OFF”, the icon is not displayed.

Note: The page above is a sample.

YES

pYou can validate also by pressing Oo().

YES

Delete thisYES

Delete allEnter you Terminal Security CodeYES

Items shown on the display (Some items cannot be executed.)

Operation and supplementary explanation for each item

Lower sub-menu item of the Function menu

Cautions or references for using each function

Operations related to the function and explanations for supplementary operations

Easy Search/Contents/Precautions

Easy Search

To retrieve a desired function with simple words, refer to the following:

To know convenient functions for making calls

To/Not to notify your phone number to the other party

....................................................................................<Caller ID Notification> 46

To switch to a videophone call during a voice call

...........................................................................<Switch to Videophone Call> 51

To change a volume level of the other party’s voice....................... <Volume> 65

To put a call on hold during a call.................................................... <Holding> 66

To do the following when you cannot answer calls

Easy Search/Contents/Precautions

To put an incoming call on hold before answering......................... <On Hold> 66

To convey the message that you need to refrain from talking on the phone

...........................................................................<Public Mode (Drive Mode)> 67

............................................................................. <Public Mode (Power Off)> 67

To record voice/video messages..........................<Record Message Setting> 69

To change melody or illumination

To adjust the ring volume........................................................<Ring Volume> 65

To change ring tones according to callers......................<Add to Phonebook> 78

To change ring tones........................................................<Select Ring Tone> 92

To know incoming calls by vibrator .................................................<Vibrator> 93

To silence the keypad sound................................................<Keypad Sound> 94

To activate Manner Mode...................................................... <Manner Mode> 96

To change colors/lighting patterns of Call indicator for incoming calls

.................................................................................................. <Illumination> 105

To change/know display settings

To know the meaning of marks (icons) on the display .....................<Display> 29

To change the menu display .................................................. <Simple Menu> 36

To change the Stand-by display (Wallpaper) ...................... <Display Setting> 98

To display a calendar on the Stand-by display..............................<Calendar> 98

To change the character size ...............................................<Character Size> 111

To make full use of mail

To send Deco-mail ...................................................................... <Deco-mail> 184

To send images ....................................................................... <Attachments> 191

To sort and save mail automatically ..............................................<Auto-sort> 212

To make full use of camera

To change the shooting size...................................................... <Image Size> 142

To save to the microSD card ...............................<Storage Setting (Store In)> 143

To display shot images......................................................... <Picture Viewer> 290

Easy Search/Contents/Precautions

To use the FOMA phone with a sense of security

To lock the FOMA phone from away when it gets lost .... <Omakase Lock>※1119

To keep Phonebook entries from prying eyes......................... <Secret Mode> 122

To reject calls without a caller ID.............................. <Call Setting without ID> 125

To reject calls from the phone numbers that are not

in the Phonebook ............................................................<Reject Unknown> 126

To separately store Phonebook and other data

files in preparation for their erasure.................... <Data Security Service>※2126

※1 This is a pay service. ※2 This is a pay service which is available on a subscription basis.

To make full use of 1Seg

To watch 1Seg programs ...................................................... <Activate 1Seg> 263

To record 1Seg programs.................. <Record Video> <Record Still Images> 270

To book/To set timer recording for 1Seg programs

...............................................................<Book Program> <Timer Recording> 271

To change settings of video and audio...................................<User Settings> 276

Other things you can do

To reduce the battery consumption .............................. <Power Saver Mode> 101

To scan QR codes or bar codes ......................................<Bar Code Reader> 146

To use the microSD card ...................................................... <microSD Card> 314

To exchange information using infrared rays.........<Infrared Data Exchange> 326

To listen to music.................................................................. <MUSIC Player> 344

To use the FOMA phone as an alarm clock .......................................<Alarm> 360

To use the FOMA phone as a calculator .....................................<Calculator> 373

To use the FOMA phone overseas........................... <International Roaming> 416

To update software programs........................................... <Software Update> 474

To update security ......................................................... <Scanning Function> 479

pThe operating procedures for frequently used functions are summarized in Quick

Manual. (See page 502)

How to Read/Refer to This Manual ... 1

Easy Search........................................4

Contents .............................................6

Main Functions of P-06A...................8

Making Full Use of P-06A!...............10

Before Using the

Handset

Voice/Videophone

Calls

Easy Search/Contents/Precautions

Phonebook

Sound/Screen/

Light Settings

Security Settings

115

Phone Parts and Functions, Display, Method for Selecting Menu, Simple Menu, Guide, UIM (FOMA Card), Battery, Charging, Power ON/OFF, Initial Setting, Set Time, Select Language, Caller ID Notification, Own Number, etc.

Making a Call/Videophone Call, Call Records, Chaku-moji, WORLD CALL, Hands-free, Receiving a Call/Videophone Call, Volume, Ring Volume, Public Mode (Drive Mode), Public Mode (Power Off), Record Message Setting, Chara-den, etc.

Available Phonebooks, Add to Phonebook (FOMA phone/UIM), Group Setting, Search Phonebook, No. of Phonebook, 2-touch Dial, Voice Dial, Data Security Service, etc.

Select Ring Tone, Vibrator, Manner Mode, Display Setting, Backlight, Menu Icon Setting, Kisekae Tool, Feel＊Mail, Illumination, Desktop Icon, Font, etc.

Passwords, Change Security Code, Releasing PIN Lock, Lock All, Omakase Lock, Self Mode, Personal Data Lock, Keypad Dial Lock, Secret Mode, Mail Security, Call Setting without ID, Reject Unknown, etc.

Safety Precautions .......................... 12

Notes on Handling........................... 18

Intellectual Property Rights............ 21

Accessories and Main Options ...... 23

Camera

129

i-mode/i-motion/

i-Channel

153

Mail

179

i-αppli

229

Osaifu-Keitai/

ToruCa

247

1Seg

259

Before Using Cameras, Still Image Shoot, Moving Image Shoot, Settings for Shooting Images, Setting Image Size/Image Quality, Bar Code Reader, Text Reader

What is i-mode?, iMenu, My Menu, Change i-mode Password, Enter URL, Bookmark, Screen Memo, Download, Upload, SSL Certificate, Client Certificate, What is i-motion?, What is i-Channel?, etc.

i-mode Mail, Deco-mail, Decome-Anime, Template, Attachments, Mail Auto-receive, Receive Option, Check New Message, Message R/F, What is Early Warning “Area Mail”?, Chat Mail, SMS, Web Mail, etc.

What is i-αppli?, i-αppli Download, i-αppli Run, iαppli Settings, Starting i-αppli Automatically, i-αppli Stand-by Display, iαppli Data

What is Osaifu-Keitai?, What is iC Transfer Service?, IC Card Content, IC Card Lock, Check IC Owner, What is ToruCa?, Obtain ToruCa Files, ToruCa Viewer, ToruCa File List/Detailed ToruCa File Display, ToruCa Settings

What is 1Seg?, Before Using 1Seg, Channel Setting, Activate 1Seg, Program Guide i-αppli, Data Broadcasting, TVlink, Recording 1Seg, Book Program/Timer Recording, User Settings

Full Browser

279

Data Management

287

Music

335

Convenient

Functions

355

Character Entry

379

Network Services

389

Full Browser, Full Browser Settings

Data Box, Picture Viewer, i-motion Player, Video Player, Chara-den, Melody Player, Kisekae Tool, microSD Card, Voice Recorder, etc.

What is Music&Video Channel?, Set Program, Playing Back/Operating Programs, Playing Back Music, Saving Music Files, MUSIC Player, Playlist

Multiaccess, Multitask, Reading Aloud, Alarm, Schedule, ToDo, Own Number, Voice Memo, Movie Memo, Call Data, Calculator, Text Memo, UIM Operation, Reset Settings, Initialize, etc.

Character Entry, Mode 1 (5-touch), Common Phrases, Cut/Copy/Paste, Own Dictionary, Learned Words, Download Dictionary, Mode 2 (2-touch), Mode 3 (NIKO-touch)

Check New Messages, Voice Mail, Call Waiting, Call Forwarding, Nuisance Call Blocking, Caller ID Request, Dual Network, Service Numbers, Remote Control, Multi Number, 2in1, OFFICEED, etc.

PC Connection

409

Overseas Use

415

Appendix/

Troubleshooting

425

Index/

Quick Manual

493

Available Data Communication, Before Using Data Communication, Preparation Flow for Data Transfer (OBEX™ Communication), Preparation Flow for Data Communication, AT Command, CD-ROM, DOCOMO Keitai Datalink

Outline of International Roaming (WORLD WING), Available Services, Confirmation for Using, Making a Call at the Country You Stay, Receiving a Call, Set Roaming Guidance, Network Services, etc.

Function List, Options and Related Equipment, Troubleshooting, Error Messages, Warranty and Maintenance Services, i-mode Trouble Diagnosis Site, Software Update, Scanning Function, Specifications, SAR, Export Administration Regulations, etc.

Index, Quick Manual, Quick Manual “For Overseas Use”

Easy Search/Contents/Precautions

Main Functions of P-06A

FOMA (Freedom Of Mobile multimedia Access) is the name of the DOCOMO service based on the W-CDMA format, authorized as one of the world’s standards for third-generation mobile telecommunication systems (IMT-2000).

◆Remarkable i-mode!

i-mode is an online service that enables you to get useful information from i-mode menu sites or i-mode web pages. This service also enables you to send or receive mail messages with ease.

◆

i-mode mail/Deco-mail/Deco-mail pictogram

Besides mail text, you can attach photos or movie files, etc. The FOMA phone supports Deco-mail/Deco-mail pictograms, so you can change the character color, character size, and background color of mail text, and insert images and moving pictographs. Further, Decome-Anime enables you to compose joyful mail messages with animations, just by inserting messages into the Decome-Anime template.

◆International Roaming P.416

Easy Search/Contents/Precautions

You can use your FOMA phone, phone number, and mail address overseas as they are. (Supported in 3G area) Voice calls, videophone calls, i-mode, i-mode mail, SMS, and network services are available.

◆High-Speed Area Supported P.410

FOMA High-Speed Area is supported so that high speed communication is available with download speed of up to 3.6 Mbps and upload speed of up to 384 kbps. ※The maximum speeds of 3.6 Mbps and 384 kbps denote the maximum speeds

specified by the technical standards. The actual speeds differ depending on the extent how networks are congested or communication environment. Your communication is enabled at the maximum 384 kbps of both upload and download speeds when you are out of the FOMA High-Speed Area, or are connecting to an access point that does not support HIGH-SPEED.

P.154

P.180, P.184, P.288

◆Mega i-αppli P.230

You can enjoy playing games or update stock price information or weather forecasts automatically.

◆Chaku-uta Full®/Uta-hodai/Music&Video Channel※

P.336, P.342, P.344

This FOMA phone supports Chaku-uta Full® that enables you to download a whole music file and Uta-hodai that enables you to enjoy listening music as much as you like at a flat rate. This FOMA phone also supports Music&Video Channel that, just by setting up beforehand, automatically downloads music programs and programs containing moving images in the night. p“Chaku-uta Full” is a registered trademark of Sony Music Entertainment Inc.

※This is a pay service which is available on a subscription basis.

◆Osaifu-Keitai/ToruCa P.248, P.250

By downloading Osaifu-Keitai compatible i-αppli, you can replenish electronic money from a site into the IC card in the FOMA phone and check your account for the balance and usage details. In addition, the “DCMX” i-αppli program that provides the DOCOMO credit service is pre-installed. Further, “iC transfer service” is supported so that you can easily move data from the existing IC card to a new one when you replace your FOMA phone such as at the time of phone model change. ToruCa is an electronic card that you can obtain from scanning devices or sites and can easily exchange using mail or infrared data exchange.

◆Kisekae Tool P.104, P.313

You can change the Stand-by display or Menu display to your favorite one at a time. You can change the order of displayed menus on P-06A according to the frequency of use to customize the Menu display as you like.

◆Feel＊Mail P.105

Animation of 45 characters and illumination reproduce the atmosphere of mail messages. Pleasant animation appears or illumination lights according to the contents of mail message.

◆One-push Open P.42

■One-push Answer P.64

When a call comes in, just press the one-push open button, and you can open the FOMA phone to answer the call.

■Recv. Mail/Call at Open P.101

When a missed call or new mail message is found, just press the one-push open button, and you can open the FOMA phone to display the detailed Missed Call display or the Inbox list.

◆View Blind P.103

You can make the display hard to see from an angle. You can use the FOMA phone without being gazed at by others.

◆Shikkari Talk P.61

You can make the other party’s voice clear according to surrounding noise.

◆Yuttari Talk P.61

You can slow down the other party’s speaking speed during a call.

◆Voice Recorder P.332

You can record your voice as a substitute for taking notes. You can repeatedly play it back, so it is convenient to record the proceedings at a meeting, etc.

◆Security Settings P.115

Various settings such as the lock functions and security settings for “safety” are available.

■Omakase Lock P.119

When you have lost the FOMA phone , you can lock the FOMA phone and release it by contacting DOCOMO. For inquiries, see the back page of this manual. pIf you are a member of the DOCOMO Premium Club, you can use this service as

often as you need without handling charge. If you are not, the service is available on chargeable basis. (You are not charged if you apply for this service at the same time as applying for the suspension of the use or during the suspension.)

pNote that Omakase Lock might be activated by an offer from the contractor of the

FOMA phone when the contractor and the user of the FOMA phone differ.

■Data Security Service P.126

This service enables you to save Phonebook entries, images, and mail messages from your FOMA phone to the Data Storage Center, and restore the saved data, when you lost your FOMA phone or in other cases, to your FOMA phone from the Data Storage Center. Further, you can edit or manage data held at the Data Storage Center using your personal computer and can reflect the edited data to your FOMA phone. For details on Data Security Service, refer to “Mobile Phone User’s Guide [i-mode] FOMA version”. For inquiries, see the back page of this manual. Data Security Service is a pay service that is available on a subscription basis.

◆Network Services P.389

pVoice Mail Service (Charged) pCall Waiting Service (Charged) pCall Forwarding Service (Free) pNuisance Call Blocking Service (Free) pDual Network Service (Charged) pMulti Number (Charged) p2in1 (Charged)

※These services are available on a subscription basis except for Nuisance Call

Blocking Service.

Easy Search/Contents/Precautions

Making Full Use of P-06A!

◆Videophone P.48

You can talk with a person who is away from you, seeing each other’s images. By the default setting, the voice of the other party is set to be output from the speakers, so you can start talking readily. You can switch, without disconnecting, from an ordinary voice call to a videophone call.

◆1Seg P.260

You can watch 1Seg (terrestrial digital TV broadcasting service for mobile objects) programs in smooth picture by the function of Mobile W-Speed. You can display captions and data broadcasting, and record a program while watching it. Use Book Program or Timer Recording not to miss an opportunity to watch or record programs.

Easy Search/Contents/Precautions

When an i-mode mail message comes in while you are watching a program, you can check the mail message in the multiwindow or by tickers. You can use the multiwindow to compose i-mode mail messages as well while watching a 1Seg program.

◆i-Channel P.176

i-Channel distributes graphical information such as news and weather forecast. By selecting your favorite channel from the Channel list, you can obtain detailed expressive information with Flash movies (see page 156).

pThis is a pay service which is available on a subscription basis. pThe service is provided only in Japanese.

Before contract

After contract

Connected

◆Chaku-moji P.54

While calling up the other party, you can have your message displayed on his/her Call Receiving display. The receiving end can know your subject/feeling by reading the message before answering the call.

◆2in1 P.400

This service enables you to have two numbers/two mail addresses on your single FOMA phone and to use your FOMA phone as if you were using two sets, by using the dedicated mode function. You can sort Phonebook entrie s, mail boxes, dialed/received call records, and Stand-by displays into “A mode” and “B mode” to manage them separately. You can also use “Dual mode” to simultaneously manage both A and B modes. pThis is a pay service which is available on a subscription basis.

A Mode

Phone number: 090-AAAA-AAAA

Mail address: XXA@docomo.ne.jp

Phonebook: For A Mode

Mode

Call/Mail in A Mode

Phonebook A Inbox A Dialed/Received Calls A Voice Mail A

・・

Phonebooks A, B Inboxes A, B Dialed/Received Calls A, B Voice Mail A, B

・・

◆MUSIC Player P.344

On a single player, you can play back and enjoy Chaku-uta Full music files, Windows Media® Audio (WMA) files, and SD-Audio files. You can download Chaku-uta Full® music files from sites and may be able to display their images and lyrics while playing them back. In the case of SD-Audio or WMA files, you can obtain your favorite music files from music CDs or Internet web pages and save them on the microSD card by using your personal computer. You can save music files also by using the Napster® application program.

B Mode

Phone number: 090-BBBB-BBBB

Mail address: XXB@docomo.ne.jp

Phonebook: For B Mode

Dual

Mode

Phonebook B Inbox B Dialed/Received Calls B Voice Mail B

・・

Mode

Call/Mail in B Mode

◆Kisekae Tool/Direct Menu P.104, P.313

This FOMA phone comes with “Direct Menu” that enables you to easily access the functions and services you frequently use. The menus are categorized into four that are arrange d at top, bottom, left, and right. The “LAST 10” button is located at the center, which automatically displays 10 items of the functions and services you used most recently. Five categorized arrangements link with the command navigation keys, so it is easy to remember the arrangements and operate the menus.

Co: SERVICES [メール (Mail), ｉモード (i -mode), ｉアプリ (i -αppli), MUSIC,

ワンセグ (1Seg), おサイフケータイ (Osaifu-Keitai), etc.]

Vo: TOOLS [アラーム (Alarm), 電卓 (Calculator), テキストメモ (Text memo),

スケジュール (Schedule), 赤外線受信 (Receive Ir data), etc.]

Xo: SETTINGS [設定 (Settings), サービス (Services), 自局番号表示 (Own number)] Zo: DATABOX [マイピクチャ (My picture), etc.] Oo: LAST10 (automatically displays 10 items of the menus you used most recently.)

※Functions are pre-installed by default.

◆Character Size P.111

You can easily change character sizes by pressing and holding x for at least one second during standby.

◆Pre-installed i-αppli P.235

■ケータイTOOL7 EX (KEITAI TOOL7 EX)

Seven useful tools are bundled into this practical i-αppli program.

Easy Search/Contents/Precautions

Safety Precautions

disassemble

■Before using the FOMA phone, read these safety precautions carefully so that

you can use it correctly. After reading the precautions, keep them in a safe place.

■Be sure to observe these safety precautions because they are designed to

protect you or those around you from causing injury and to avoid unnecessary damage to the property.

■The symbols below indicate the levels of danger or damage that can be caused

if the particular precautions are not observed.

Danger

Warning

Easy Search/Contents/Precautions

Caution

Always follow the safety precautions.

This symbol indicates that incorrect handling will almost certainly cause death or serious injury.

This symbol indicates that incorrect handling poses a risk of causing death or serious injury.

This symbol indicates that incorrect handling poses a risk of causing injury or damage to the product or property.

■The following symbols show specific directions:

Denotes things not to do. (Prohibition)

Don’t

Denotes not to disassemble.

Do not

Not wet

hands

Avoid

Water

Denotes not to touch with wet hands.

Denotes not to use where it could get wet or not to wet it.

Denotes mandatory instructions (matters that must be complied with).

Pull the

power plug

■“Safety Precautions” are divided into the following six sections:

General precautions for FOMA phone, batteries, adapters/chargers, and

UIM ............................................................................................................. P.13

Precautions for FOMA phone .................................................................... P.14

Precautions for batteries ............................................................................ P.16

Precautions for adapters/chargers............................................................. P.16

Precautions for UIM.................................................................................... P.17

Notes on using near electronic medical equipment .................................. P.18

Denotes to pull the power plug out of the outlet.

out

General precautions for FOMA

Don’t

Do not

disassemble

Avoid

Water

Don’t

phone, batteries, adapters/chargers, and UIM

Danger

Do not use, store, or leave the mobile phone or its accessories in places with a high temperature (such as near fire, near heating appliances, inside a kotatsu or near other furniture with heating elements, in places exposed to direct sunlight, or in cars heated by the sun).

The devices could be deformed or malfunction, or the battery may leak, overheat, burst, or catch fire, thus resulting in the deterioration of performance and shortening of the life of devices. Also, part of the case could get heated, causing bare skin burns.

Do not disassemble, modify or solder the FOMA phone or accessories.

Accidents such as fire, injury, or electric shock, or malfunction may result. The battery may leak, overheat, burst or catch fire.

Do not wet the FOMA phone or accessories.

If liquids such as water or pet urine get onto them, overheating, electric shock, fire, malfunction, injury or others may result. Pay attention to the place of use and the way of handling.

With your FOMA phone, use the batteries and adapters/chargers specified by NTT DOCOMO, INC.

If you use any type of battery, adapter or

charger other than the specified one, your FOMA phone, battery or other accessories may leak, overheat, burst, catch fire or malfunction. Battery Pack P16 FOMA AC Adapter 01/02 FOMA AC Adapter 01 for Global use FOMA DC Adapter 01/02 Desktop Holder P25 FOMA Dry Battery Adapter 01 FOMA Portable Charging Adapter 01 FOMA USB Cable with Charge Function 01/02 ※For other compatible products,

contact a handling counter such as a docomo shop.

Warning

Do not place the batteries, the FOMA phone, adapters/chargers, or UIM in cooking appliances such as microwave ovens or high-pressure containers.

The battery may leak, overheat, burst, or catch fire. The FOMA phone or the adapter/charger may overheat, smoke, or catch fire, or its circuit parts may become damaged.

Do not throw the FOMA phone or accessories, or subject them to severe shocks.

Don’t

The battery may leak, overheat, burst, or catch fire. Also, malfunction or fire may result.

Be careful not to let electroconductive materials (metal pieces, pencil leads etc.) contact with the charging terminal or connector terminal. Also, make sure that those are not entered into the inside of the FOMA phone.

Short-circuit could cause fire or malfunction of the FOMA phone.

When you are in a place such as a gas station where flammable gas is generated, turn off the FOMA phone, and never do charging. Otherwise, catching fire may result.

Ensure that you use Osaifu-Keitai with the FOMA phone turned off when you are in the vicinity of the gas station. (When IC Card Lock is set, turn off the power with the lock released.)

If odor, overheat, discoloration, or deformation is detected during use, battery charge, or storage, immediately observe the following:

1. Pull the power plug out of the outlet or cigarette lighter socket.

2. Turn off the power to the FOMA phone.

3. Remove the battery pack from the FOMA phone.

If you use the FOMA phone and its accessories as they are, overheat, burst, or catching fire could result or the battery could leak.

Easy Search/Contents/Precautions

Caution

Do not place the FOMA phone or accessories on unstable locations such as wobbly tables

Don’t

or slanted locations.

The FOMA phone or accessories may fall, resulting in injury or malfunction.

Do not store in humid or dusty places, or in high temperature environments.

Malfunction may result.

If children use the FOMA phone or accessories, a guardian should explain the safety precautions and correct operations. The guardian

should also make sure that the instructions are followed during use.

Otherwise, injury may result.

Keep out of the reach of babies and infants.

Accidental swallowing or injury may result.

Be especially careful when you use the FOMA phone for a long time with the adapter/charger connected.

If you use i-αppli programs, talk on the videophone, watch 1Seg programs and so on for a long time during charging, the temperature of the FOMA phone, battery pack, or adapter/charger might rise. If you directly touch the part of high temperature continuously, redness, itching, rash, or low-temperature bare skin burns may result depending on your physical conditions or predisposition.

Precautions for FOMA phone

Warning

Do not directly point the infrared data port at someone’s eyes during transmission.

Don’t

His/her eyes may possibly be affected. Other infrared devices may operate erroneously if the infrared data port is pointed at them during transmission.

Do not put the FOMA phone in the place where it could be affected by an expanded airbag, e.g., on the dashboard.

If the airbag expands, the FOMA phone could hit you and others, causing accidents such as injury and the FOMA phone could malfunction and become damaged.

If you have any implanted electronic medical equipment, do not place your FOMA phone in a chest pocket or inner pocket.

If the FOMA phone is positioned close to electronic medical equipment, it may cause that equipment to malfunction.

Do not allow liquids such as water, or foreign materials such as metal pieces or flammable materials to get into the UIM or microSD card slot of the FOMA phone.

Fire, electric shock or malfunction may result.

Turn off the FOMA phone in places where use is prohibited such as in airplanes and hospitals.

Otherwise, electronic devices and electronic medical appliances may be adversely affected. If the Auto Power ON function is set, deactivate the setting, then turn the power off. For use inside medical facilities, make sure that you comply with their regulations. You may be punished for using the FOMA phone in airplanes, which is prohibited by law.

When talking with the FOMA phone set to Hands-free, be sure to keep the FOMA phone away from your ear.

Further, when you play games or play back music with the earphone/microphone connected, adjust the sound volume to moderate volume.

The excessive sound volume impairs your hearing. Further, accidents may result due to the hardness of hearing of surrounding sound.

For those with weak heart conditions, the vibrator and ring volume must be adjusted carefully.

Those functions may cause an effect on

the heart.

If thunder starts to rumble while you are using the FOMA phone outdoors, turn off the power and move to a safe place.

Otherwise, you could be struck by lightning or suffer an electric shock.

Turn off the FOMA phone when

near electronic devices using high-precision control or weak signals.

The FOMA phone may possibly cause these devices to malfunction.

※

Electronic devices that may be affected: Hearing aids, implanted cardiac pacemakers, implanted defibrillators, other medical electronic devices, fire alarms, automatic doors and other automatically controlled devices. If you use an implanted cardiac pacemaker, implanted defibrillator or any other electronic medical device, consult the manufacturer or retailer of the device for advice regarding possible effects from the radio waves.

If the display part or camera lens is broken, be careful about broken glasses or the exposed interior of the FOMA phone.

Plastic panels are used for the surfaces of the display part and camera lens so that glasses do not easily get scattered, however, pay attention not to erroneously touch the broken part or interior. Otherwise, injury may result.

Caution

Do not swing the FOMA phone by its strap.

The FOMA phone may hit you or

Don’t

persons around you, and accidents such as injury or malfunction and damage may result.

Don’t

Do not place magnetic cards or similar objects near the FOMA phone or between phone parts.

Magnetic data on cash cards, credit cards, telephone cards and floppy disks, etc. may be deleted.

Do not bring magnetic substances close to your FOMA phone.

Strong magnetic items might cause in erroneous operation.

If you erroneously break the display part and then crystal liquid gets leaked, never take or suck the liquid to or into your mouth, or apply to skin. If the crystal liquid gets into the eyes or mouth, immediately rinse it out with clean water and then seek medical attention. When it adheres to your skin or clothes, immediately wipe it away with alcohol etc., and then rinse it out with water and soap.

Otherwise, the loss of eyesight or injury to your skin may result.

Do not bring your ears close to the speakers while a ring tone sounds or a melody is played back from the FOMA phone.

Otherwise, your hearing could be impaired.

Do not open the FOMA phone by pressing the one-push open button near persons around you or your face.

The FOMA phone may hit you or persons around you, causing accidents and injuries.

Electronic devices in some types of cars can be affected by use of the FOMA phone.

For safety’s sake, make sure not to use

the FOMA phone inside such cars.

Itching, rash or eczema may be caused depending on your physical conditions or predisposition. If an abnormality

occurs, stop using the FOMA phone immediately, and then

Metals are used for the following parts:

Where it is used Material Finishing

Charging terminal Phosphor

Panel of the Private window

seek medical attention.

bronze

Acrylic Evaporated tin,

Gold-plated finish with nickel-plated ground

hard coating

Be careful not to get your finger or a strap caught in the parts when you close or open the FOMA phone.

Accidents such as injury or damage may result.

When you watch a 1Seg program, watch in a place bright enough taking a certain distance from the display.

Otherwise, your visual acuity could be reduced.

Easy Search/Contents/Precautions

Precautions for batteries

■Check the description on the label of the

battery pack for the type of battery.

Description Type

Li-ion Lithium-ion battery

Danger

Do not let any metal object such as a wire come in contact the battery terminals. Also do not

Don’t

Easy Search/Contents/Precautions

Don’t

carry or store the battery together with any metal objects like a necklace.

The battery may leak, overheat, burst or catch fire.

Do not use excessive force to attach the battery to the FOMA phone even when you cannot attach it successfully. Also, check that the battery is the right way round when you attach it.

The battery may leak, overheat, burst or catch fire.

Do not throw the battery into fire.

The battery may leak, overheat, burst or catch fire.

Do not pierce it with nails, hit it with a hammer, or step on it.

The battery may leak, overheat, burst or catch fire.

If the battery fluid gets into your eyes, do not rub them. Flush your eyes with clean water and seek medical attention immediately.

Otherwise, the loss of eyesight may result.

Warning

When any abnormality due to external shock such as the deformation or scratches by

Don’t

dropping is found on the battery pack, immediately stop using it.

The battery may leak, overheat, burst, or catch fire. Also, malfunction or fire may result.

If charging is not completed at the end of the specified charging time, stop charging.

Otherwise, the battery may leak,

overheat, become damaged or catch fire.

Immediately stop using the FOMA phone and keep it away from fire if the battery leaks or emits an odor

The leaked battery fluid may ignite, causing fire or burst.

Be careful that your pets do not bite into the battery pack.

The battery may leak, overheat, burst, or catch fire. Also, malfunction or fire may

result.

Caution

An exhausted battery should not be disposed of with other waste.

The battery may catch fire or damage

Don’t

the environment. After insulating the battery terminals with tape, take the unneeded battery to a handling counter such as a docomo shop or dispose of it in accordance with local waste disposal regulations.

Do not charge the wet battery.

The battery pack may overheat, catch fire, or burst.

Don’t

If the battery fluid comes in contact with skin or clothes, immediately stop using, then rinse it out thoroughly with clean

water.

Skin injury may result.

Precautions for adapters/chargers

Warning

Don’t

Do not use a damaged adapter/ charger cord or power cord.

Electric shock, overheating or fire may result.

Do not use the AC adapter and desktop holder in steamy places such as a bathroom.

Electric shock may occur.

Don’t

Not wet

hands

The DC adapter is for use only in a negative (-) grounded vehicle. Do not use it in a positive (+) grounded vehicle.

Fire may result.

If it starts to thunder, do not touch the FOMA phone and adapter/charger.

You might be struck by lighting or suffer an electric shock.

Never short-circuit the charging terminal when the adapter is plugged into the power outlet or cigarette lighter socket. Also, never touch the charging terminal with fingers or other bare skin.

Fire, malfunction, electric shock or injury may result.

Place the charger and desktop holder on a stable location during charging. Do not cover or wrap the charger and desktop holder in cloth or bedding.

The FOMA phone may drop off, or the charger and desktop holder may overheat, causing fire or malfunction.

Do not place something heavy on the adapter/charger cord and power cord.

Electric shock or fire may result.

Do not touch the power cord of the adapter/charger, or power outlet with wet hands.

Electric shock may result.

Use the adapter/charger at the specified V AC.

If you use it at a wrong voltage, fire or malfunction may result. When using the

FOMA phone overseas, use FOMA AC adapter available overseas. AC adapter: 100 V AC DC adapter: 12/24 V DC [For negative (-) grounded vehicles only] AC adapter available overseas: 100 V to 240 V AC [Connect only to household AC outlet]

If a fuse of the DC adapter has blown, replace it with a specified fuse.

If you use an unspecified fuse, fire or

malfunction may result. For the specified fuse, refer to each instruction manual.

Keep the power plugs dust-free.

Otherwise, fire may result.

When pulling the AC adapter into the power outlet, firmly plug it in, taking care not to contact with metal straps or the like.

Otherwise, electric shock, short-circuit or fire may result.

When removing the adapter/ charger out of the outlet or cigarette lighter socket, do not forcibly pull the adapter/charger

cord or power cord, instead take hold of the power plug and then pull.

If you pull the plug out by the cord, the cord may be damaged, which could result in electric shock or fire.

When the adapter/charger is not to be used for a long period of time, unplug the power cord from

Pull the

power plug

the outlet.

Otherwise, electric shock, fire, or malfunction may result.

If liquids such as water get in the charger, unplug the power cord immediately from the outlet or

Pull the

power plug

cigarette lighter socket.

Otherwise, electric shock, smoke or fire may result.

out

Before cleaning, pull the power plug out of the outlet or cigarette lighter socket.

Pull the

power plug

Otherwise, electric shock may result.

out

Precautions for UIM

Caution

Be careful not to touch the cut surface of the UIM (IC portion) when removing it.

You may hurt your hand or fingers.

Easy Search/Contents/Precautions

Notes on using near electronic

medical equipment

■The description below meets “Guidelines on

the Use of Radio-communication Equipment such as Cellular Telephones – Safeguards for Electronic Medical Equipment” by the Electromagnetic Compatibility Conference Japan.

Warning

Comply with the following in hospitals or health care facilities:

•Do not carry the FOMA phone into operating rooms, intensive care units

(ICU) or coronary care units (CCU).

•Turn off the FOMA phone in hospital wards.

Easy Search/Contents/Precautions

•If there is any electronic medical equipment near you, turn off the FOMA phone even when in a location such as a lobby.

•Comply with any regulations of hospital and health care facilities instructing you not to use or carry in a mobile phone.

•If the Auto Power ON function is set, deactivate the setting, then turn the power off.

Turn off the FOMA phone in crowded areas such as inside trains during rush hour, as someone with an implanted

cardiac pacemaker or implanted defibrillator may be near you.

Operation of an implanted cardiac pacemaker or implanted defibrillator can be affected by radio waves.

If you use an implanted cardiac pacemaker or implanted defibrillator, use the mobile phone 22 cm or more away from

an implanted cardiac pacemaker or implanted defibrillator.

Operation of an implanted cardiac pacemaker or implanted defibrillator can be affected by radio waves.

Patients using electronic medical equipment other than implanted cardiac pacemakers or implanted defibrillators (outside medical

establishments for treatment at home, etc.) should check the influence of radio waves upon the equipment by consulting its manufacturer.

Operation of electronic medical equipment can be affected by radio waves.

Notes on Handling

General notes

■Do not wet the equipment.

The FOMA phone, battery, adapter/charger, and UIM are not waterproofed. Do not use them in environments, which are high in humidity such as in bathrooms, and do not allow them to get wet from rain. Furthermore, if carrying them against your body, they become moist due to perspiration and the internal parts may become corroded, causing malfunction. If the parts are found to have been damaged due to exposure to the liquids, any repairs will not be covered by warranty, or repairs may not be possible. This may be repaired at a cost if repairs are possible.

■Use a dry soft cloth such as the one for

cleaning glasses to clean the equipment.

pThe screen of the FOMA phone sometimes has a

special coating so that they are easier to see. If you rub it roughly with a dry cloth, it might be scratched. Take care of the way of handling, and use only a dry, soft cloth such as the one for cleaning glasses. If the screen is left with water drop or stain adhered, smear may be generated or the coating might peel off.

pDo not use alcohol, thinner, benzene, detergent or

other solvents for cleaning, otherwise the printing may be removed or discoloration may result.

■Occasionally clean the terminals of the

equipment using a dry cotton swab.

If the terminals become soiled, the connection might deteriorate so that the power turns off or the battery does not charge fully. Wipe the terminals with a dry cloth or cotton swab.

■Do not place the FOMA phone near an air

conditioner outlets.

Condensation may form due to rapid changes in temperature, and this may corrode internal parts and cause malfunction.

■Do not apply excessive force onto the FOMA

phone and battery pack.

If you put the FOMA phone in a bag along with many other articles or sit with the FOMA phone in a clothes pocket, the display, internal circuitry and the battery pack could be damaged or malfunction. Also, if an external device is left connected to the connector terminal, the connector could be damaged, or malfunction.

■Carefully read each instruction manual

attached to the FOMA phone, adapter/ charger, or desktop holder.

■Do not rub or scratch the display part with

metals.

Doing so might cause damage to the part, resulting in trouble or malfunction.

Notes on handling the FOMA phone

■Avoid using in extremely high or low

temperatures.

The FOMA phone should be used within a temperature range of 5°C to 35°C and a humidity range of 45% to 85%.

■The FOMA phone, if operated near landline

phones, television sets, radios or other devices that are in use, may affect them. You should operate your FOMA phone as far away from such equipment as possible.

■It is recommended that you make separate

notes of the information stored in the FOMA phone and keep such notes in a safe place.

We take no responsibility for any loss of the stored data items.

■Do not drop the FOMA phone or subject it to

strong impacts.

Malfunction or damage may result.

■Do not insert an external device to the

connector terminal (Earphone-Microphone terminal) at a slant when connecting, and do not pull it out when it is inserted.

Malfunction or damage may result.

■Make sure that nothing, such as a strap, gets

caught between the parts of the FOMA phone when you close it.

Otherwise, malfunction or damage may result.

■The FOMA phone becomes warm during use

or charging but this is not an abnormality. Use the FOMA phone as it is.

■Do not leave the camera in places exposed to

direct sunlight.

Pixels may be discolored or burns may result.

■Usually, put the cover of the connector

terminal and microSD card slot to use the FOMA phone.

Dust or water might enter into the FOMA phone, causing malfunction.

■Do not use the FOMA phone with the back

cover left removed.

The battery pack might come out, or malfunction or damage may result.

■Do not apply an excessively thick sticker onto

the surfaces of the display, keys, or buttons.

Malfunction may result.

■While you are using the microSD card, never

take it off or turn off the power to the FOMA phone.

Data may be erased or malfunction may result.

Notes on handling batteries

■Batteries have a limited life.

Though it varies depending on the usage state, you are advised to replace the battery if its usable time is extr emely short even when you fully char ge it. Make sure that you buy the specified battery.

■Charge the battery in a place with an appropriate

ambient temperature of 5°C to 35°C.

■Make sure that the battery is charged when you

use the FOMA phone for the first time or have not used it for a long period of time.

■The usable time of the battery differs depending

on the usage environment or its remaining life.

■Depending on how the battery pack is used, it

might swell as its operating life becomes short, but this is not a problem.

■Note the following points when you store a

battery pack over a long period:

•Storage in a fully charged state (the state immediately after charging is completed)

•Storage with no battery power left (the state you cannot turn on the power of the handset due to battery dr ain)

These may lower the battery pack’s performance and shorten its operating life. You are advised to store the battery pack in the state of two bars of battery icon indication as a guide for when you store it for a long period.

Notes on handling chargers/adapters

■Charge the battery in a place with an

appropriate ambient temperature of 5°C to 35°C.

■Charge the battery where:

•There is very little humidity, vibration, and dust.

•There are no landline phones, television sets or radios

nearby.

■During charging, the adapter/charger may

become warm. This is not an abnormality, so continue charging.

Easy Search/Contents/Precautions

■Do not use the DC adapter for charging the

battery when the car engine is not running.

The car battery could go flat.

■When using the power outlet having the

disengaging prevention mechanism, observe the instructions given in that instruction manual.

■Do not give a strong shock. Also, do not

deform the charging terminal.

Malfunction may result.

■Be careful not to get your finger or the adapter/

charger cord caught in the parts when you house the stand of the desktop holder.

Accidents such as injury or damage may result.

Notes on handling the UIM

■Never use more force than necessary when

inserting/removing the UIM.

■The UIM may become warm during use, but

this is not a sign of a malfunction. Continue

Easy Search/Contents/Precautions

using it as it is.

■The warranty does not cover damage caused

by inserting the UIM into some other types of IC card reader/writer.

■Always keep the IC portion clean.

■Use a dry soft cloth such as the one for

cleaning glasses to clean the equipment.

■It is recommended that you make separate

notes of the information stored on the UIM and keep such notes in a safe place.

We take no responsibility for any loss of the stored data items.

■For the environmental protection, bring any

unneeded UIMs to a handling counter such as a docomo shop.

■Avoid using in extremely high or low

temperatures.

■Do not damage, carelessly touch, or

short-circuit the IC.

Data might be lost or malfunction may result.

■Do not drop the UIM or subject it to strong

impacts.

Malfunction may result.

■Do not bend the UIM or place something

heavy on it.

Malfunction may result.

■Into the FOMA phone, do not insert the UIM

with a label or sticker pasted.

Malfunction may result.

Notes on handling the FeliCa reader/ writer

■The FeliCa reader/writer function on the

FOMA phone uses very weak radio waves which do not require to be licensed as radio stations.

■The FeliCa reader/writer is operated on the

13.56 MHz frequencies. When you use another reader/writer nearby, take enough distance between your FOMA phone and the reader/writer. Further, ensure that there are no radio stations that use the same frequencies.

Caution

■Do not use the modified FOMA phone. Using

a modified FOMA phone infringes the Radio Law.

The FOMA phones are granted technical regulations conformity certification as the specified radio equipment under the Radio Law and bear a “technical conformity mark ” on the nameplate as evidence of conformity. Unscrewing the FOMA phone and modifying internal components void the technical regulations conformity certification. Do not use the FOMA phone in this state, which infringes the Radio Law.

■Be especially careful not to operate the FOMA

phone while driving.

You will be imposed punishment if you use the mobile phone in your hand while driving. If you answer a call out of necessity, tell the caller with Hands-free that you will call him/her back, park your car to somewhere safe, and then dial.

■Use the FeliCa reader/writer functions in

Japan only.

The FeliCa reader/writer functions on the FOMA phone have been authorized in compliance with the radio transmission standards in Japan. You might be imposed punishment if you use them overseas.

Intellectual Property Rights

Copyrights and Portrait Rights

You have no right to copy, modify, or distribute the contents such as text, images, music, or software programs downloaded from web pages on the Internet, or images shot by the cameras of this product without permission from the copyright holder except for when the copy or quote is for personal use that is allowed by the copyright law. Note that it may be prohibited to shoot or record live performances or exhibitions even for personal use. Make sure that you refrain from shooting portraits of other persons and distributing such portraits over the Internet without consent, as this violates portrait rights.

Trademarks

p“FOMA”, “mova”, “i-mode”, “i-αppli”, “i-αppliDX”, “i-motion”, “Deco-mail”,

“Chaku-motion”, “Chara-den”, “ToruCa”, “mopera”, “mopera U”, “WORLD CALL”, “Dual Network”, “FirstPass”, “visualnet”, “V-live”, “i-Channel”, “DCMX”, “iD”, “Security Scan”, “i-motion mail”, “i-area”, “Short Mail ”, “WORLD WING”, “Public mode”, “DoPa”, “sigmarion”, “musea”, “IMCS”, “OFFICEED”, “2in1”, “docomo STYLE series”, and the logos of “FOMA”, “i-mode”, “i-αppli”, “DCMX”, “iC”, “iD”, “Music&Video Channel”, and “HIGH-SPEED” are trademarks or registered trademarks of NTT DOCOMO, INC.

p“Catch Phone (Call waiting service)” is a registered trademark of Nippon Telegraph and

Telephone Corporation.

pFree Dial logo mark is a registered trademark of NTT Communications Corporation. pMcAfee® is registered trademarks or trademarks of McAfee, Inc. and/or its affiliates in

the US and/or other countries.

pG-GUIDE, G-GUIDE MOBILE and their logos are registered trademarks in

Japan of U.S. Gemstar-TV Guide International, Inc. and/or its affiliates.

pQuickTime is a registered trademark of Apple Inc., in the US and other

countries.

pNAVIDIAL and NAVIDIAL logo mark are trademarks of NTT Communications

Corporation.

pMicrosoft

pWindows Media® is either a registered trademark or trademark of Microsoft

, Windows®, and Windows Vista® are trademarks or registered trademarks

of Microsoft Corporation in the United States and other countries.

Corporation in the United States and/or other countries.

Powered by JBlend™ Copyright 2002-2008 Aplix Corporation. All rights reserved. JBlend and JBlend-related trademarks are trademarks or registered trademarks of Aplix Corporation in Japan and other countries.

p is a registered trademark of FeliCa Networks, Inc. pmicroSDHC logo is a trademark.

p“Multitask” is a registered trademark of NEC Corporation.

pQR code is a registered trademark of Denso Wave Inc. p使いかたナビ® is a registered trademark of CANNAC, Inc. p“One-push Open™” is a trademark of Panasonic Corporation. pJava and all Java based trademarks and logos are trademarks or registered

trademarks of Sun Microsystems, Inc. in the U.S. and other countries.

pPowered by Mascot Capsule®/Micro3D Edition™

Mascot Capsule®is a trademark of HI CORPORATION.

pNapster is a registered trademark of Napster, LLC. and/or its affiliates in the US and/or

other countries.

pOther company names and product names described in the text are trademarks or

registered trademarks of those companies.

Others

pThis product contains NetFront Browser and NetFront Sync Client of

pIrFront is a trademark or registered trademark of ACCESS CO., LTD. in Japan and

other countries. The IrDA Feature Trademark is owned by the Infrared Data Association and used under license therefrom.

Contains Adobe® Flash®Lite™ technology by Adobe Systems Incorporated. Adobe Flash Lite Copyright rights reserved. Adobe, Flash and Flash Lite are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.

pAdobe and Adobe Reader are either registered trademarks or trademarks of Adobe

Systems Incorporated in the United States and/or other countries.

pFeliCa is a contactless IC card technology developed by Sony Corporation. pFeliCa is a registered trademark of Sony Corporation.

2003-2007 Adobe System Incorporated. All

Easy Search/Contents/Precautions

pLicensed by QUALCOMM Incorporated under one or more of the following United

States Patents and/or their counterparts in other nations: 4,901,307 5,504,773 5,109,390 5,535,239 5,267,262 5,600,754 5,416,797 5,490,165 5,101,501 5,511,073 5,267,261 5,568,483 5,414,796 5,659,569 5,056,109 5,506,865 5,228,054 5,544,196 5,337,338 5,657,420 5,710,784 5,778,338

pThis product contains software licensed complying with GNU General Public License

(GPL), GNU Lesser General Public License (LGPL), etc. For more details, see “readme.txt” in the “GPL・LGPL等について” folder on the bundled CD-ROM. (“readme.txt” is only available in Japanese version.)

pThis product is licensed under the MPEG-4 patent portfolio license and AVC patent

portfolio license for the personal and non-commercial use of a consumer to

(i) encode video in compliance with the MPEG-4 Visual Standard and AVC Standard

(“MPEG-4/AVC Video”) and/or

(ii) decode MPEG-4/AVC Video that was encoded by a consumer engaged in a

personal and non-commercial activity and/or was obtained from a licensed video

provider licensed to provide MPEG-4/AVC Video. No license is granted or implied for any other use. Additional information may be obtained from MPEG LA, L.L.C. See http://www.mpegla.com.

Easy Search/Contents/Precautions

pThis product is manufactured or sold under license from InterDigital

Technology Corporation.

pThe abbreviations used for respective operating systems (Japanese version) in this

manual are as shown below: Windows Vista is the abbreviation of Windows Vista® (Home Basic, Home Premium, Business, Enterprise, and Ultimate). Windows XP is the abbreviation of Microsoft® Windows® XP Professional operating system or Microsoft® Windows® XP Home Edition operating system. Windows 2000 is the abbreviation of Microsoft operating system.

pThis product is protected by certain intellectual property rights of Microsoft Corporation

and third parties. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary and third parties.

pThis product is protected by certain intellectual property rights of Microsoft Corporation.

Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary.

Windows® 2000 Professional

pContent providers are using the digital rights management technology for Windows

Media contained in this device (“WM-DRM”) to protect the integrity of their content (“Secure Content”) so that their intellectual property, including copyright, in such content is not misappropriated. This device uses WM-DRM Software to play Secure Content (“WM-DRM Software”). If the security of the WM-DRM Software in this device has been compromised, owners of Secure Content (“Secure Content Owners”) may request that Microsoft revoke the WM-DRM Software’s right to acquire new licenses to copy, display and/or play Secure Content. Revocation does not alter the WM-DRM Software’s ability to play unprotected content. A list of Revoked WM-DRM Software is sent to your device whenever you download a license for Secure Content from the Internet or from a PC. Microsoft may, in conjunction with such license, also download revocation lists onto your device on behalf of Secure Content Owners.

Accessories and Main Options

pP-06A Handset

(With Warranty and Back Cover P34)

p P-06A CD-ROM

The PDF versions of “Manual for PC Connection” and “Kuten Code List” are included.

pFOMA AC Adapter 01/02

(With Warranty and Instruction Manual)

Easy Search/Contents/Precautions

pInstruction Manual

Quick Manual included (See page 502)

pBattery Pack P16 pDesktop Holder P25

NTTドコモ

(With Instruction Manual)

Other Options → See page 458

Before Using the Handset

Phone Parts and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Navigation Displays and Key Operations . . . . . . . . . . . . . . . . . 28

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Displaying Description of Icons . . . . . . . . . . . . . . . . . . <Icons> 31

Private Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Method for Selecting Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Using Simple Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

When You do not Remember Key Operation . . . . . . . <Guide> 37

Using UIM (FOMA Card) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Attaching/Removing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Opening FOMA Phone by Using a Button

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <One-push Open> 42

Checking Battery Level . . . . . . . . . . . . . . . . . . .<Battery Level> 43

Turning Power On/Off . . . . . . . . . . . . . . . . . . <Power ON/OFF> 43

Switching to English . . . . . . . . . . . . . . . . . .<Select Language> 44

Executing Initial Settings . . . . . . . . . . . . . . . . .<Initial Setting> 44

Setting Date and Time . . . . . . . . . . . . . . . . . . . . . . . <Set Time> 45

Displaying World Time . . . . . . . . . . . . . . <World Time Watch> 46

Notifying the Other Party of Your Phone Number

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Caller ID Notification> 46

Checking Your Own Number . . . . . . . . . . . . . . <Own Number> 46

Phone Parts and Functions







Before Using the Handset



  



■ For using earphone

Connect an optional connector-terminal-compatible earphone. When using a connector-terminal-non-compatible earphone, use an optional plug adapter for connection. pWhen inserting or pulling the plug adapter, take hold of the plug for the

handset side and insert or pull it straight. Be careful not to take hold of the cover of the connector terminal and plug for the handset side together when you pull it out.









 







 







Flat plug of the Flat-plug Earphone/ Microphone with Switch

Earphone

Example for connecting the Flat-plug Earphone/Microphon e with Switch (option)

terminal (Flat-plug)



Plug for handset side

Light sensor









･For sensing brightness (See page 102)

pDo not cover the light sensor with your hands or do no t

put a sticker on it. Doing so might disable you to detect the brightness.

Display

(See page 29)

l Mail key

･For showing the Mail menu (See page 201) ･For operating the function corresponding to the

navigation displays (See page 28)

･For checking new messages (See page 196)

m Menu key/IC Card Lock key

･For showing Main Menu (See page 32) ･For operating the function corresponding to the

navigation displays (See page 28)

･For locking the IC card (See page 250)

r Clear key

･For returning to the previous operation ･For clearing entered text or a phone number

･For resetting Main Menu (See page 104)

d Send/Answer key, Hands-free key

･For making/receiving calls (See page 48 and page 62) ･For talking with Hands-free (See page 61)

･For accessing a voice dial entry (See page 89)

Microphone

･For speaking to the other party

Infrared data port

･Used for infrared data exchange and the infrared

remote-controller. (See page 326 and page 330)

Earpiece

･For listening to the other party’s voice

o Command navigation key

･For operating functions and menus (See page 28)

i i-mode key/i-αppli key

･For showing the i-mode menu (See page 154) ･For operating the function corresponding to the

navigation displays (See page 28)

･For showing the i-αppli Software list (See page 231)

c Camera key/1Seg key

･For activating the camera in “Photo mode”

(See page 137)

･For switching the camera mode while the camera is

activated (See page 131)

･For operating the function corresponding to the

navigation displays (See page 28)

･For starting 1Seg (See page 263)

h Power/End key

･For ending calls ・For ending respective functions ･For turning on the power (for at least one second)/

For turning off the power (for at least two seconds) (See page 43)

Numeric keys

･For entering phone numbers and text

ps(for at least one second)

For activating Manner Mode (See page 96)

pa(for at least one second)

For activating Public Mode (Drive Mode) (See page 67)

p5(for at least one second)

For switching the backlight on/off (See page 102)

p8(for at least one second)

For switching View Blind on/off (See page 103)

x Multi key

･For showing the Multitask Menu (See page 358)

･For switching character sizes (See page 111) ･For switching functions when multiple functions are

running (See page 358)

Connector terminal

･For connecting the AC adapter (option), DC adapter

(option), FOMA USB Cable with Charge Function 01/ 02 (option), Stereo Earphone Set 01 (option), etc.

Call/Charging indicator

･Flickers for incoming calls/mail and during a call.

(See page 105)

･Lights in red during charging. ･Lights/Flickers when you shoot with the camera.

Private window

(See page 31)

Camera

･For shooting portraits and/or landscapes

(See page 130)

･For catching sight of persons and/or landscapes

during a videophone call

Speakers

･For sounding ring tones ･For listening to the other party’s voice when

Hands-free is activated (See page 61)

fmark

･The IC card is mounted.

pUse the IC card function placing this mark over the

scanning device. You cannot dismount the IC card. (See page 249)

FOMA antenna/1Seg antenna

pThe antenna is embedded in the FOMA phone. Do

not cover the antenna with your hand for better communication/receiving.

microSD card slot

･For inserting microSD card (See page 314)

Back cover

･Remove this when attaching/removing the battery

pack and UIM. (See page 37 and page 39)

pDo not peel off the silver sticker on the back of the

back cover. If you peel it off, you might not be able to read and write the IC card.

Charging terminal

Strap hole <Side ▲ key

･For scrolling up page by page

<Press and hold for at least one second with the

FOMA phone opened>

･For activating 2in1 (See page 400)

!>Side ▼ key

･For scrolling down page by page ･For using Record Message (See page 70) ･For checking for missed calls and new mail

(See page 107)

<Press and hold for at least one second with the

FOMA phone opened>

･For playing back a videophone record message or

movie memo. (See page 71)

<Press and hold for at least one second with the

FOMA phone closed>

･For activating Manner Mode (See page 96)

"One-push open button

(See page 42)

Before Using the Handset

Navigation Displays and Key Operations

When you want to execute the operation shown on the display, press the corresponding key as below.

■Basic display examples and key assignments

Before Using the Handset

Indicates the operation you can perform with the



l key.

Indicates the operation you can perform with the



m key.

Indicates the operation you can perform with the

Oo key.



Indicates the direction in which you can scroll and select items with the Mo key.

Indicates the operation you can perform with the



c key.

Indicates the operation you can perform with the



i key.

■Operating command navigation key

Up Zo

・Moves the cursor or highlighted

display up. (Press and hold to scr oll continuously.)

・Scrolls the display while a site or mail

text is displayed.

・

Press from the Stand-by display to bring up the Channel list. (See page 176)

・Converts entered characters to

katakana, kanji or other char acters. (See page 381)

Left/Received Calls Co

・Moves the cursor to the left. ・Press from the Stand-by display to

bring up the Received Call list. Press and hold for at least one second to bring up the Received Address list. (See page 53 and page 210)

・Scrolls back page by page. (Press

and hold to scroll continuously.)

・Returns to the previous page while

displaying a site.

OK key Oo

・Fixes the operation.

Right/Redial Vo

・Moves the cursor to the right. ・Press from the Stand-by display to

bring up the Redial list. Press an d hold for at least one second t o bring up the Sent Address list. (See page 52 and page 210)

・Scrolls forward page by page. (Press

and hold to scroll continuously.)

・Moves to the next page while

displaying a site.

Down Xo

・Moves the cursor or highlighted

display down. (Press and hold to scroll continuously.)

・Scrolls the display while a site or

mail text is displayed.

・Press from the Stand-by display to

bring up the Search Phonebook display. Press and hold for at least one second to store a Phoneboo k entry. (See page 78 and page 83)

・Converts entered characters to kanji,

katakana or other characters. (See page 381)

・Adjusts the camera focus for

shooting. (See page 142)

Display













(dark blue)



(dark blue)

Battery level (estimate) (See page 43)

Radio waves reception level (est imate)

Strong Weak

You are out of the FOMA service area or radio waves do not reach.

During Self Mode (See page 11 9)

During i-mode (See page 154 )

During i-mode communication (S ee page 154)

During packet communication (The icon differs depending on the communication status.)

You get out of the service area while Network Search Mode is set to “Manual”. (See page 421)

During SSL communication (See page 155)

Unread i-mode mail or an SMS message

(pink)

exists. (See page 194 and page 226)

The area for i-mode mail and SMS messages in the FOMA phone is full. (See page 195 and page 226)

The area for SMS messages on the UIM (FOMA card) is full.

Unread mail exists, and the area for SMS

(pink)

messages on the UIM (FOMA card) is full.

Both the FOMA phone and UIM (FOMA card) are full.

Area Mail exists. (See page 219)





(yellow)



(dark blue)



(yellow)

(dark blue)











(pink)

! 

Unread Messages R/F exist. (See page 216)

The area for Messages R/F in the FOMA phone is full. (See page 217)

i-mode mail is held at the i-mode Center. (See page 196)

The box for i-mode mail at the i-mode Center is full. (See page 195)

Messages R/F are held at the i-mode Center. (See page 217)

The box for Messages R/F at the i-mode Center is full. (See page 217)

i-mode mail is held at the i-mode Center while Receive Option Setting is se t to “ON”. (See page 195)

During a voice call

During a videophone call

During 64K data communication











A microSD card is inserted. (See page 315)

Data is being read to/written f rom the microSD card.

A write-protected microSD card is inserted. (See page 315)

The inserted microSD card cann ot be used. (See page 315)

A microSD card is inserted, and the FOMA USB Cable with Charge Function 01/02 (option) is connected in micro SD Mode. (See page 322)

A microSD card is inserted, and the FOMA USB Cable with Charge Function 01/02 (option) is connected in MTP M ode. (See page 322)

During Lock All (See page 118)

During Personal Data Lock (See page 120)

During Keypad Dial Lock (See page 1 21)

During Secret Mode or Secret Data Only (See page 122)

Before Using the Handset











During IC Card Lock (See page 250)

Both Keypad Dial Lock and Personal Data Lock are set.

Both Keypad Dial Lock and Secret Mode/ Secret Data Only are set.

Both IC Card Lock and Lock All ar e set.

Both IC Card Lock and Personal Data Lock are set.

Both IC Card Lock and Keypad D ial Lock are set.

Both IC Card Lock and Secret M ode/Secret Data Only are set.

IC Card Lock, Keypad Dial Lock, and Personal Data Lock are simultaneously set.

IC Card Lock, Keypad Dial Lock, and Secret Mode/Secret Data Only are simultaneously set.

Type of in-use network (See page 417)

You are in the OFFICEED area. (See page 406)

Timer Lock ON At Close is set. (See page 121)

During Multitask (See page 357)

Multiple functions are activated. (See page 357)

While watching a 1Seg program (See page 263)

During recording of a 1Seg pr ogram (See page 270)

During recording of a 1Seg pr ogram by Timer Recording (See page 274)

During pause of 1Seg program recording (See page 270)

During music playback (Se e page 345)

During music pause (See page 345)

During infrared data exchang e (See page 326 and page 330)

The FOMA USB Cable with Charge Function 01/02 (option) is connected in Communication Mode.

The FOMA USB Cable with Charge Function 01/02 (option) is connected in microSD Mode. (See page 322)























During talk or communication through a USB Hands-free compatible device (See page 61)

A USB Hands-free compatible device is connected. (See page 61)

A USB Hands-free compatible device is connected in microSD Mode. (See page 61)

Vibrator is set. (See page 93)

Ring Volume is set to “Silent” or Mail/Msg. Ring Time is set to “OFF”. (See page 65 and page 95)

During Manner Mode (See page 96)

During Public Mode (Drive Mode) (See page 67)

The call cost has exceeded the specified limit. (See page 372)

An alarm is set. (See page 274 and page 361)

A Music&Video Channel program is booked. (See page 336)

Backlight is set to “OFF”. (See page 102)

Side Keys Guard is set to “ON”. (See page 122)

USB Mode Setting is set to “microSD mode”. (See page 322)

USB Mode Setting is set to “MTP mode”. (See page 322)



pThe clock at the upper right of the display does not

appear when the icon  or  is displayed.

pWhen the Stand-by display is shown, the notification

icon or desktop icon appears. (See page 107)

Information

pSome characters and symbols on the display and

Private window might be modified or abbreviated. In addition, the Private window is displayed in monochrome.

pThe color liquid crystal display uses high-precision

production technology. The slightest change in the environment or other factors may result in unlit or permanently lit pixels, but this is not a manufacturing defect.

Voice mail messages for Number B are held

〜・

at the Voice Mail Center in Dual M ode of 2in1. (See page 405)

Voice mail messages are held at the Voice

〜・

Mail Center. (See page 390)

The number of record m essages

〜

(See page 69)

The number of videophone record

〜

messages (See page 69)

<Icons>

+m-3-6

Displaying Description of Icons

The symbols on the display (such as , , and ) are called icons. You can check the meanings of them on the display.

mSettingsDisplayIcons

Use Mo to highlight an icon.

Private Window

Various information is displayed on the Private window like the following examples: Information is displayed for about 15 seconds in cases such as when you press </> with the FOMA phone closed.

Clock Receiving a call

When a missed call is found

When the FOMA phone is closed, “Missed call” appears. Press < to display the missed call record. The name is displayed for the missed call coming from the party stored in the Phonebook. When there are multiple missed calls, up to three missed call records are displayed each time you press <. pIf you have received 30 or more incoming calls after a missed

call, the missed call record disappears.

pMissed call records might not be displayed while another

function is activated.

pAfter you display a missed call record, “Missed call” disappears.

Dialing

During a voice call

When a new mail message or Message R/F is received

When the FOMA phone is closed, a Feel＊Mail image is played back, and then “New mail” appears. When you press <, the latest Feel＊Mail image is played back. (For Messages R/F, the Feel＊Mail image is not played back.) When “Mail” on page 101 is set to “ON”, the received date/time, sender’s address (name), and subject of the mail or the received date/time and subject of the Message R/F are displayed. The sender’s name is displayed for the mail coming from the party stored in the Phonebook. When multiple mail messages or Messages R/F are received, up to three mail messages or Messages R/F appear each time you press < with “New mail” displayed. pPress < to end the playback of the Feel＊Mail image or to clear

the received date/time, and others.

pFor the mail messages and Messages R/F sorted to the box or folder with security set,

the Feel＊Mail images, received date/time, and others are not played back/displayed.

pWhen a mail message or Message R/F comes in while “Receiving display” is set to

“Operation preferred” and a display other than the Stand-by display is shown, “New

mail” appears without showing any information.

pDepending on the setting of “Auto-display”, “New mail” appears without showing any

information when a Message R/F comes in.

pAfter you display the received date/time and others of the received mail or Message

R/F, “New mail” disappears.

pWhen a mail message or Message R/F comes in during a voice call or a videophone

call, information is not displayed even when “Receiving display” is set to “Alarm

preferred”.

pWhen you set “Secret mail display” to “OFF” and you receive a secret mail message in

Normal Mode, a Feel＊Mail image is not played back.

When i-Channel is received

When “i-Channel ticker” on page 101 is set to “ON” and the FOMA phone is closed, tickers flow on the Private window. pPress </> to end the tickers’ flow.

Change Clock Display

You can change displayed contents by pressing < while clock is shown.

Before Using the Handset

Time only Icons and Date/time

Method for Selecting Menu

Press m of the FOMA phone to bring up Main Menu so that you can execute, set, or check respective functions.

pThis manual explains the operations mainly by the method for selecting functions from

Main Menu. Menus are classified by functions. (Seepage 426)

pSome functions can be selected also by the operation other than pressing m. In this

manual, the operation by the easier way is described.

pYou can also switch to Simple Menu (see page 36) focusing on only basic functions for

easy operation. Menus are classified by functions. (See page 444)

This FOMA phone supports Kisekae Tool (see page 104). If you use Kisekae Tool to change the design of the Menu display, some menu configurations change according to the usage frequency depending on the type of the menu. Further, some menu numbers that are assigned to the menu items do not apply.

■Scroll Selection

Main Menu is composed of 12 main menu icons indicating each function. pIf you select a main menu icon, the Sub-menu Item Selection display appears. If you

further select a sub-menu item, the Lower Sub-menu Item Selection display appears.

Before Using the Handset

pBy repeating selecting, you can set and check the function.

■Menu Number Selection

You can display some functions by pressing m + menu number (see page 426).

■Multitask is Supported

pYou can simultaneously use some functions in Main Menu. (See page 357)

Scroll Selection

In this manual, the description of the command navigation key operation (selection of top/bottom/left/right, and press of Oo after selecting/ entering a function item) is omitted. Scroll selection is explained below using the example of selecting the function “Quality alarm”:

Description Example of Steps

Main menu icon

m

No tone . . . . . . . . .

High tone Low tone

Sub-menu item

SettingsTalkQuality alarmSelect an alarm.

Does not sound.

. . . . . . . .

High alarm sounds.

. . . . . . . .

Low alarm sounds.

Items which appear on the display

Function name of lower sub-menu item

Select a main menu icon from the menu function

Select “Settings” from Main Menu.

Main Menu

pPress +Mo to highlight the icon. Press and hold +Mo to scroll

the icons continuously.

pIf you have not touched any key for 15 seconds, the

Stand-by display returns.

+Mo

+Oo

Select a sub-menu item from the menu function

Select “Talk” from “Settings”.

Select a desired lower sub-menu item (function)

Select “Quality alarm” from “Talk”.

Before Using the Handset

+Oo+Bo

pThe highlighted item is the currently selected one. pPress +Xo to highlight the item below, and +Zo to highlight the item above. pPress and hold +Bo to scroll the items continuously. pPress +No to scroll page by page.

+Oo+Bo

pPress +Xo to highlight the item below, and +Zo to highlight the item above. pPress and hold +Bo to scroll the items continuously. pWhen the items are listed over multiple pages, the total number of pages and the

current page number are shown at the upper right of the display.

Set or check the function

Some menu items have even more detailed menus. The example below shows how to set “Low tone” for “Quality alarm”.

Bring up the function using the menu number

From the Stand-by display, press m75.

+Oo+Bo

Before Using the Handset

pThe highlighted item is the currently selected one. pPress +Xo to highlight the item below, and +Zo to highlight the item above. pPress and hold +Bo to scroll the items continuously.

Menu Number Selection

Menu Number Selection is explained below using the following example:

Description Example of Menu Number

Menu number



+m-7-5

Sounding Alarm when a Line is Likely to be Disconnedted

-7-5

Function Menu

If you press i when “ ” is shown at the lower right of the display, the Function menu including selectable items such as “Save”, “Edit”, and “Delete” appears in each operation. The contents of the Function menu depend on the display from which you bring up the Function menu.

pWhen the items are listed

over multiple pages, the total number of pages and the current page number are shown at the upper right of the Function Menu display.

Description Example for Function Menu

In this manual, the operation of the Function menu is described as follows:

Item displayed in the Function menu

Operating procedures after selecting an item in the Function menu

Function menu

Delete all You can delete all files.

Operation/Explanation



Enter your Terminal Security CodeYES

An actual operation is done as follows:

Press +i().

Use +Mo to highlight “Delete all” and press

+Oo().

Enter your Terminal Security Code and press

+Oo().

Use +Bo to highlight “YES” and press

+Oo().

To select an item quickly <Direct selection>

Press the numeric key corresponding to the displayed item number.

Item number

Item scroll

When menu items are listed over multiple pages, you can show the previous/next page by pressing Bo with the uppermost/lowermost item highlighted. You can press No to scroll through page by page. When / is displayed on the display, you can scroll through page by page also by pressing m()/c(). pDepending on the display being shown, such as lower sub-menu items, you might be

able to scroll through page by page also by pressing </> instead of No.

Check box

With the functions you can select multiple items, put a check mark for check boxes to select them. Each time you press

Oo( ), you can switch

With some functions, you can put or clear check marks at a time by pressingi()and selecting “Select all/Release all”or by pressing m(/).

“”

is placed to the selected item depending on the function.

“”

and

“”

After finishing the operation

The Lower Sub-menu Item Selection display is shown. When you press h, the Stand-by display returns (except during Multitask). The Stand-by display or the former display automatically returns depending on the function.

To cancel the operation midway

Press h. The contents of the setting are abandoned and the Stand-by display or the former display returns. The confirmation display appears asking whether to abandon the setting contents depending on the function. You can press r to return to the previous operation.

When the “YES/NO” selection display appears

Press Bo to highlight “YES” or “NO”, then press Oo().

Before Using the Handset

For Reset Settings

Using Simple Menu

Simple Menu is a menu focusing on only basic functions for easy operation.

pThis manual describes the operating procedures in Normal Main Menu only. For how

to operate in Simple Menu, see the respective pages of each function.

pSee the Function List for the contents of Simple Menu. (See page 444) pYou cannot use the Multitask function. (See page 357)

Switch to Simple Menu

You can switch between Normal Main Menu and Simple Menu.

From the Stand-by display, press m.

Configuration of Simple Menu

Phone Mail i-mode Camera

1Seg Tools Settings

Before Using the Handset

Normal Main Menu

When the confirmation display appears asking whether to change to large fonts,select “YES” to set “Set at one time” on page 111 to “Extra large”. Even when you release Simple Menu, the setting does not return. When “Extra large” has already been set, the confirmation display does not appear.

Simple Menu

<Guide>

When You do not Remember Key Operation

You can search for the functions you want to know and use, and then check the operating methods. You can execute some functions from “

使いかたナビ

2 3

(Guide)”. This function is available in Japanese Mode only.

mステーショナリー



使いかたナビ

おすすめ機能 (Recommendable functions)

. . . Displays the recommendable functions. Go to step 3.

キーワード検索 (From keywords)

. . . Enter keywords and retrieve. Go to step 2

機能一覧検索 (From Function list)

. . . Retrieves from the function list. Go to step 3.

検索履歴 (Search history)

. . . Displays up to 30 search histories. Go to step 3. pHighlight each item and press l( ); then the

detailed operating methods are displayed. If you highlight “キーワード検索 (From keywords)” and press l( ), select “キーワード検索 (From keywords)” or “文字入力のしかた (How to input words)”.

pThe 使いかたナビ(Guide) display appears also by selecting the 使いかたナビ

(Guide) icon “ ” pasted on the desktop at purchase.

(Guide)Select an item.

(Stationery)

Enter a keyword.

Up to 50 search results are displayed. pYou can enter up to 24 full-pitch/48 half-pitch characters.

Select a functionSelect an item.

機能の説明 (Description) . . . . . . . .Displays explanations for the function.

操作のしかた (How to operate) . . . Displays the operating method. この機能を使う (Operate function)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Executes the function. Operate each function.

関連機能 (Relevant function) . . . . .Displays up to 10 relevant functions. Repeat

pFor some functions, press Oo( ) several times for selection. pYou can display explanations about the function also by pressing l()

while highlighting the function.

pTo delete search history, press i( ) and select “1件削除 (Delete this)” or

“全削除 (Delete all)”, then select “YES”.

step 3.

Using UIM (FOMA Card)

The UIM is an IC card that holds your information such as phone numbers. It can hold data such as Phonebook entries and SMS messages as well. By sharing a UIM, you can operate multiple FOMA phones for multiple purposes. You cannot use the FOMA phone for communication such as voice and videophone calls, i-mode, sending/receiving mail, or packet communication unless the UIM is inserted. For details on how to use the UIM, refer to the UIM instruction manual. When inserting or removing the UIM, take care not to accidentally touch or scratch the IC.

Insert/Remove

You need to turn off the power and then remove the battery before you insert the UIM. (See page 39)

■Inserting

With the golden IC surface

downward, push the UIM slowly to the end while pressing the surface of it.

■Removing

While sliding the UIM, pull it out

slowly.

Cut

Before Using the Handset

Information

pMake sure that you insert/remove the UIM with the FOMA phone closed and held in

your hand.

pTake care not to force the UIM into place because this can break it. pTake care not to lose the UIM once you remove it. pWhen you replace your UIM (except during Omakase Lock), you need to enter the

four- to eight-digit Terminal Security Code after turning on the power. When you enter the correct Terminal Security Code, the Stand-by display appears. If you enter the incorrect Terminal Security Code five times in succession, the power turns off. (However, you can turn on the power again.)

Password

You can set two passwords, PIN1 and PIN2, for a UIM. (See page 116)

Security Function of UIM

The FOMA phone has the UIM security function (UIM restriction function)

Before Using the Handset

as a security function to protect your data files. If you obtain data files by the method below with the UIM inserted, UIM security function is automatically set to them.

・When downloading images or melodies and so on, from sites or

Internet web pages

・When receiving i-mode mail with file attachments

The data files with the UIM security can be browsed, played back, started, edited, attached to mail, or transferred via infrared rays only when the UIM used for obtaining is inserted. When the UIM used for obtaining the data or files is not inserted, or when another UIM is inserted, these functions are not operable.

pIn the explanation hereafter, the UIM used to obtain data and files is referred to

as “your UIM” and other UIMs as “another person’s UIM”.

♪

If the UIM used for obtaining data files or mail messages is inserted, you can browse/play back the data files with the UIM security.

pWhen the UIM is not inserted or when another person’s UIM is inserted, the following

types of data and files are displayed with the restrictions symbol, “ ”:

・Videophone record messages ・Movie memos ・Screen memos ・Templates ・i-αppli programs ・Images ・i-motion movies ・Chara-den images ・Melodies ・Kisekae Tool files ・Chaku-uta®/Chaku-uta Full® music files ・Downloaded dictionaries ・Files attached or pasted to i-mode mail in the Inbox ・Files attached to i-mode mail in the Outbox/Draft (except the data shot or edited

with the FOMA phone)

・Messages R/F with files (melodies or images) attached or pasted ・Images inserted into Deco-mail text

※This function applies to the pre-installed i-αppli programs, Chara-den images,

Deco-mail pictograms, etc. if they are reinstalled (upgraded) from a site.

※“Chaku-uta” is a registered trademark of Sony Music Entertainment Inc.

pThe preview image for the data file with the UIM security appears as

shown on the right.

Replacing UIMs

Your UIM

Another

person’s UIM

♪

Unless the UIM used for obtaining data files or mail messages is inserted, you cannot browse/play back the data files with the UIM security.

♪

Information

pWhen the UIM security is set for data files, you cannot set them for the functions such

as “Display setting” and “Select ring tone” when another person’s UIM is inserted.

pWhen the data files with the UIM security is set for “Display setting” or “Select ring

tone”, the FOMA phone works with their default settings if you replace your UIM with another person’s UIM. If you insert your UIM again, your settings are enabled again.

pThe UIM security function is not set for the data files received using the infrared data

exchange function or data transmission (OBEX™ communication) function and the still images/moving images shot or edited with the FOMA phone.

pEven when another person’s UIM is inserted, you can move/delete data files with the

UIM security.

pThe settings of the following functions are stored on the UIM:

・SMS validity period ・SMS center selection ・Select language ・PLMN setting ・PIN1 code, PIN2 code ・PIN1 code entry set ・Validating/Invalidating DoCoMo Certificate 1 and user certificate

Types of UIM (FOMA Card)

If you use the blue UIM with your FOMA phone, note that following specifications differ from those of the green/white UIM:

Functions

Number of digits of the phone number that can be stored in the UIM Phonebook

Operation of user certificate to use FirstPass

Use of WORLD WING Cannot be used Can be used 416

Use of Service Numbers for “DOCOMO repair counter” and “General inquiries <docomo Information Center>”

Cannot be used Can be used 172

Cannot be used Can be used 397

UIM

(blue)

20 max. 26 max. 79

(green/white)

Reference

■WORLD WING

WORLD WING is the DOCOMO FOMA international roaming service that enables you to use the current phone number overseas for making and receiving calls using the UIM (green/white) and service compatible mobile phone. You can use P-06A only in the DOCOMO 3G roaming service area. For using in a GSM service area, insert the UIM into a GSM service compatible mobile phone. pYou do not need to subscribe to WORLD WING if you have subscribed to the FOMA

service after September 1, 2005. If you offered that you did not need WORLD WING at the time you signed up for the FOMA service, or when you have midway canceled WORLD WING, you are required to take the procedures to newly subscribe to WORLD WING.

pIf you have signed up for the FOMA service before August 31, 2005, and have not

yet subscribed to WORLD WING, you are required to subscribe to it.

pThis service is not available with some billing plans. pIf you lose your UIM (green/white) or have it stolen overseas, immediately contact

DOCOMO to take the steps necessary for suspending the use of the UIM. For inquiries, see “docomo Information Center” on the back page of this manual. Note that you are still charged the call and communication fees incurred after you lose it or have it stolen.

Attaching/Removing Batteries

Use the FOMA phone’s dedicated Battery Pack P16.

■Attaching

While pressing the “ ” part of

the back cover in the direction A, slide the back cover (2 mm or more) in the direction B to unlock.

Before Using the Handset

With the arrow mark facing up, fit

the tab side of the battery pack to the FOMA phone securely, and then push the battery pack into the direction B while pressing it against the direction A.

Arrow mark

Slide the back cover in the

direction of the arrow and attach it in place.

■Removing

Before Using the Handset

While pressing the “ ” part of

the back cover in the direction of A, slide the back cover (2 mm or more) in the direction of B to unlock.

Take hold of the projection of the

battery pack to lift it up.

Projection

Information

pMake sure that you attach/remove the battery with the FOMA phone closed and held

in your hand after you turn off the power. Also, make sure not to press the one-push open button when you attach/remove the battery.

pIf you try to force the battery into place, you could damage the UIM or the charging

terminal of the FOMA phone.

Charging

Use the FOMA phone’s dedicated Battery Pack P16. Life of battery pack

pBattery packs are consumables. The usable time shortens slightly each time they are

charged.

pWhen the usable time of the battery pack becomes half the time it was purchased,

replacing is recommended because the battery pack is nearing the end of its life. Depending on the use conditions, the battery pack may swell as it nears the end of its life, but this is not a problem.

pThe life of the battery pack may shorten if you use i-αppli programs, talk on the

videophone, watch 1Seg programs and so on for a long time during charging.

For environmental protection, bring the unneeded battery pack to an NTT docomo shop, dealer, or recycle shop.

Charging

pFor details, refer to the instruction manuals for the FOMA AC Adapter 01/02 (option),

FOMA AC Adapter 01 for Global use (option), and FOMA DC Adapter 01/02 (option).

pThe FOMA AC Adapter 01 supports 100 V AC only. The FOMA AC Adapter 02 and

FOMA AC Adapter 01 for Global use support from 100 V AC through 240 V AC.

pThe shape of the plug for the AC adapter is for 100 V AC (for domestic use). To use the

AC adapter that supports from 100 V AC through 240 V AC overseas, you need to have a conversion plug adapter that is compatible with the voltage of the country you stay. Do not use a transformer for overseas travel to charge the battery pack.

pEven during charging, you can still answer calls if the FOMA phone is turned on. This

will consume the charged amount so that charging will take longer. Also, the standby time or talk time might be shorter if you charge the battery pack with your FOMA phone open.

pIf you have a long time videophone call during charging, the temperature in the FOMA

phone may rise and charging may be suspended. In such a case, wait for a while and try charging again.

pRemove and insert the connector slowly and carefully, without using unnecessary

force.

pDo not remove the battery pack during charging.

Li-ion 00

Do not charge for long periods of time (several days) with the FOMA phone turned on.

pIf you leave the FOMA phone powered on for long periods of time during charging, you

may not be able to use the FOMA phone for long duration as expected and the low battery alarm may sound soon, because the FOMA phone receives the power from the battery pack after charging is completed. If this happens, charge the battery pack correctly. When charging the battery pack again, first remove the FOMA phone from the AC adapter (or desktop holder) or DC adapter and then set it again.

Estimated usable time for battery pack (The usable time for the battery pack

varies with the charging time and the remaining life of the battery pack.)

Continuous standby time (FOMA/3G) Continuous talk time (FOMA/3G) 1Seg watching time Approx. 290 minutes

※The continuous talk time is the estimated time that the FOMA phone can be used for

calls when radio waves can be sent and received normally.

※The 1Seg watching time is the estimated time for when radio waves can be received

normally with the Stereo Earphone Set 01 (option) connected.

※The continuous standby time is the estimated time for when radio waves can be

received normally. The talk/communication time and standby time could be about half of this estimate and 1Seg watching time could be shorter depending on the charge level of the battery pack, function settings, other ambient conditions such as temperature, and the status of radio waves in the area (weak or no radio waves, for instance). When you use i-mode communication, the talk/communication time and standby time will be shorter. Further, even if you do not make calls or not execute i-mode communication, the talk/communication time and standby time will be shorter if you watch 1Seg programs, compose i-mode mail, start up a downloaded i-αppli program or the i-αppli Stand-by display, execute data communication or Multiaccess, use the camera, or play back music.

※The continuous talk time and the continuous standby time may be shortened

depending on the network environment in the country you stay.

※The continuous standby time for standstill is the average number of hours you can use

the FOMA phone in standstill status when it is closed and can receive radio waves normally.

※The continuous standby time for in motion is the average number of hours you can

use the FOMA phone in the combined status of “standstill” “moving” and “out of the service area” when it is closed, in an area where it can receive radio waves normally.

Estimated time for charging battery pack

AC adapter Approx.

※The charging time is an estimate of time for when empty battery pack is charged with

the FOMA phone turned off. The charging time will be longer if you charge the battery pack with the power of the FOMA phone turned on.

Standstill: Approx. 570 hours In motion: Approx. 400 hours Voice call: Approx. 190 minutes Videophone call: Approx. 130 minutes

(When Mobile W-Speed is ON: Approx. 220 minutes)

(In ECO Mode: Approx. 330 minutes)

130

minutes DC adapter Approx.

130

minutes

Charge with AC Adapter and Desktop Holder

Connect the AC adapter

Call/Charging indicator

(option) to the desktop holder (option).

Insert the AC adapter’s

plug into a power socket.

Put the head of the FOMA

phone into the stopper of the desktop holder (A) to fit the bottom to the lock claw, and then depress the FOMA phone until it clicks (B).

Check that the Call/Charging indicator lights in red. When the Call/Charging indicator flickers, dismount the AC adapter and battery pack from the FOMA phone and then re-mount them for charging. If the symptom persists, troubles with the AC adapter, desktop holder or battery pack may be involved, so consult a handling counter such as a docomo shop. pThe charging confirmation tone (see page 95) sounds when charging starts and

ends. However, it does not sound when the power is off or during Manner Mode or Public Mode (Drive Mode).

pBe sure to set the FOMA phone firmly onto the desktop holder. Also, be careful

that the connector cover or a commercial strap is not caught between the FOMA phone and desktop holder.

pCharging can be done even when the FOMA phone is open.

Desktop Holder P25

Lock claw

Power socket

100 V AC

Plug in horizontally with engraved side facing down

FOMA AC Adapter 01/02

AC Adapter’s plug

When charging is completed, hold the desktop holder

with fingers and lift up the bottom of the FOMA phone to remove.

pUnplug the AC adapter from the power socket when you are not going to use it for

a long time.

Before Using the Handset

Stopper

Connector

■Indicator and display during charging and when charging is completed

Call/Charging indicator “ ” display

Charging Lights in red Blinks

Charging completed Off Lights

pWhen the FOMA phone is turned off, “ ” does not appear.

If you start charging with the battery flat, the Call/Charging indicator might not light immediately; however, charging itself has started.

■Stand of Desktop Holder

To enable you to easily watch 1Seg programs, place the desktop holder upright and then incline with your FOMA phone mounted. When operating the FOMA phone, ensure that you take securely hold of the desktop holder so that it does not fall down or the FOMA phone does not drop off the desktop holder. ※Be careful that the stand of desktop holder might be damaged if you apply an

excessive force onto it such as by depressing from above.

Before Using the Handset

Raise the stand as far as it goes.

■DC adapter (option) With the DC adapter, you can use a cigarette lighter socket (12 V/24 V) of cars to charge the FOMA phone with the battery pack attached. For details, refer to the instruction manual for the FOMA DC Adapter 01/02.

Information

pIf the fuse blows off when charging with the DC adapter, be sure to use a 2A fuse. The

2A fuse is consumables, so purchase at auto parts stores in your neighborhood.

<One-push Open>

Opening FOMA Phone by Using a Button

You can open the FOMA phone easily by one-push key operation. (One-push Open)

p You can open it also manually without using the button. p You need to close the FOMA phone manually. If it does not close, open it fully and

then close it.

Connector terminal

Stand

When charging only with the AC adapter

Insert the connector with the engraved surface facing up until it clicks. Pull straight the connector out while pressing the release buttons. ※Check the facing direction (front or rear)

of the AC adapter plug and then insert or pull it horizontally into or out of the FOMA phone. Malfunction could result if you try to pull it forcibly.

Release buttons

Engraved surface

One-push open button

Information

p When you open the FOMA phone by pressing the one-push open button, it might

not open fully depending on its direction.

p When you open the FOMA phone by pressing the one-push open button, be

careful not to drop it by its rebound.

Checking Battery Level

When the FOMA phone is turned on, an estimate of the battery level is indicated by the icon.

・Almost full. . . . . . . . . . . . . . . . . . .

・Getting low . . . . . . . . . . . . . . . . . .

・Almost empty . . . . . . . . . . . . . . . .

pCharge the battery when it is almost empty.

Check by Display and Tone

You can check an estimate of the battery level by the display and sound.

mSettingsOther settingsBatteryBattery level

Almost full Getting low Almost empty

Three beeps Two beeps One beep

※Almost empty.

pThe pictograph disappears in about three seconds.

When the battery is running out

The display on the right appears and the low battery alarm sounds for about 10 seconds. To stop this alarm, press any key other than < and >. About one minute later, the FOMA phone will be turned off. pDuring a call, a beeping tone from the earpiece notifies you of

the low battery. About 20 seconds later your call will be cut and then one minute later the FOMA phone will be turned off.

Charge the battery.

Turning Power On/Off

Turn Power On

Press and hold h for at least one

second.

After the Wake-up display (see page 99) is displayed, the Stand-by display appears. pIf you have stored many Phonebook entries or mail

messages, it may take a while for the display to appear.

pIf Set Time is set, the current date and time are shown. pWhen “ ” is displayed, the FOMA phone is out of the

service area or in the place where the radio waves do not reach. Move to a location where “ ” disappears.

pIf “Starting system Wait a minute” is displayed when

you turn on the power, wait for a while and then proceed.

When your UIM is replaced (except during Omakase Lock)

Enter the four- to eight-digit Terminal Security Code after turning on the power. When you enter the correct Terminal Security Code, the Stand-by display appears. If you enter the incorrect Terminal Security Code five times in succession, the power turns off. (However, you can turn on the power again.)

When “PIN1 code entry set” of “UIM setting” is set to “ON”

Enter the four- to eight-digit PIN1 code after you turn on the power. When you enter the correct PIN1 code, the Stand-by display appears. See page 116 for PIN1 code.

When “Auto reset setting” of “Notice call cost” is set to “ON” (except during Omakase Lock)

Enter the four- to eight-digit PIN2 code after you turn on the power. When you enter the correct PIN2 code, the Stand-by display appears. If you press r or h without entering the correct PIN2 code, “Auto reset setting” is set to “OFF” and the Stand-by display appears. See page 116 for PIN2 code.

Stand-by display

Before Using the Handset

Recharge Battery

display

Check Welcome Mail

The mail message “Welcome デコメアニメ (Welcome Decome-Anime )” has been saved by default. Press +Oo twice or perform the operation of “Display Mail from Inbox” on page 199 to show the mail message.

Information

pEach entry display appears in the order of “PIN1 code” → “Terminal Security Code”

→ “PIN2 code”.

Turn Power Off

Press and hold h for at least two seconds.

The exit display appears and the power turns off. pYou cannot turn on the power immediately after turning off the power. Wait a few

seconds.

Before Using the Handset

+m-1-5

Switching to English

m設定 (Settings)ディスプレイ (Display)

バイリンガル (Select language) Japanese (日本語) or English (英語)

pThe following functions are different between Japanese display and English

display:

Functions Japanese English

Info Notice Setting 電子音 (Electrical tone)

“Clock” of Display Setting

→ “Day of week”

使いかたナビ (Guide) Available Not available

Voice Guidance Available Not available

Information

pWhen you insert the UIM, the “バイリンガル (Select language)” setting is stored on

the UIM.

ボイス (Voice)

OFF

Available Not available

Not available

OFF

Executing Initial Settings

If the date and time, Terminal Security Code, Keypad Sound, or Character Size is not set, the Initial Setting display appears when you turn on the power. You can set the initial settings also from each menu function separately.

Turn on the powerYES

pWhen the display for entering your Terminal Security

Code, PIN1 code, or PIN2 code appears, follow the operation on page 43.

Set the date and time.

You can select “Auto time adjust ON” or “Auto time adjust OFF” for setting the time. (See page 45)

Set your Terminal Security Code.

You can set your Terminal Security Code required for setting functions. (See page 116)

1. Enter “0000”Enter your new Terminal Security Code (four to eight digits)

YES

Set Keypad Sound.

You can set whether to make a keypad sound. (See page 94)

Set the size of characters.

You can set the size of characters on the display at a time. (See page 111)

Information

pWhen an unset function is found, the Initial Setting display for the unset function

appears each time you turn on the power.

pThe completed settings are valid even when total setting is interrupted by an incoming

call or canceled by pressing -h or -r midway.

Information

pWhen the power is automatically turned on by alarm notification, the Initial Setting

display does not appear even if there is any unset function.

pWhen you finish the initial settings, the confirmation display appears telling that

updating software is executed automatically. This display appears only at the first time, and after that, does not appear until you execute Reset Settings or Initialize.

+m-3-1

Setting Date and Time

You can select whether to correct the time automatically or set it manually. The time is set/displayed on the 24-hour basis.

mSettingsClockSet time

Auto time adjust ON or Auto time adjust OFF

Auto time adjust ON

. . . .Corrects the date/time automatically. The setting is completed.

When the time cannot be corrected automatically such as when “ ” is displayed and the date/time has not been set, the Manual Time Setting display appears. Follow step 2 to set the date/time.

Auto time adjust OFF

. . . .Sets the date/time manually.

pWhen “Notice call cost” is set to “ON”, you need to enter your Terminal Security

Code.

Enter year, month, date and time.

Use Mo to move the cursor and enter numbers by the numeric keys. pTo enter one-digit numeral for the date and time, enter

two digits beginning with “0” as in “01” through “09”.

pHighlight “time zone” and press l( ) to set the

time zone. Use Mo to select a region and press

Oo().

About date/time correction function

This function corrects the time of the FOMA phone according to the clock information obtained from the network when you turn on the power. The time is corrected when you show the Stand-by display with “Auto time adjust ON” set. If the time is not corrected for a while after you turn on the power, turn it off and then on again.

Some few second errors might occur. You might not be able to correct the time depending

on the radio wave conditions, or the i-αppli program set for the i-αppli Stand-by display.

pWhen you receive the clock information overseas and the time difference correction

information differs from the previously received one, “Time is adjusted” is displayed and

the time difference is corrected automatically. Press “OK” to update the time and show

Redial, Dialed Calls, Received Calls, sent/received mail messages and others in local

time.

pDepending on the network overseas, the time difference might not be correctly

adjusted. In such a case, set a time zone manually.

Information

pUnless Set Time is set, the functions which use the clock such as Schedule do not

work correctly. Further, the date/time for redial items and received call records are not stored.

pThe set time is retained even when the battery pack is replaced, however, it might be

reset if the battery pack is left removed for a long time. In that case, charge the FOMA phone and then perform the clock setting.

pWhen “time zone” is set to other than “GMT +9” or the time difference is corrected

overseas, the sub clock (Japanese date/time, etc.) is displayed under the Stand-by display clock. However, the sub clock is displayed over the Stand-by display clock when “Clock display” is set to “Largest”.

pThis function supports clock settings from 00:00 on January 1, 2008 through 23:59 on

December 31, 2037.

Before Using the Handset

Displaying World Time

You can display the time of the specified area under the Stand-by display clock.

mSettingsClockWorld time watchON or OFF

Use Mo to select an area and press Oo().

Information

pWorld Time Watch is not displayed when “Display setting” → “Clock” → “Clock

display” is set to “OFF”, or when you use the FOMA phone overseas.

pWorld Time Watch is displayed on the upper side of the Stand-by display clock when

“Clock display” is set to “Largest”.

Summer Time

Before Using the Handset

You can advance the time displayed for the overseas country you stay and for a region of World Time Watch by one hour.

mSettingsClockSummer timeON or OFF

Notifying the Other Party of Your Phone Number

You can set the FOMA phone to send your phone number to the called party’s phone when dialing. Your phone number is important information, so take utmost care when notifying your phone number. This function is available only when the other party’s phone supports Caller ID.

Set Caller ID Notification to Network

You can set whether to notify your caller ID on the network.

+m-1-7

mServiceCaller ID notification

Do the following operations.

Item Operation/Explanation

Activate ON or OFF

Check setting You can check the setting contents of “Activate”.

+m-0

Checking Your Own Number

pYour phone number (own number) is stored on the UIM.

mPhonebookOwn number

You can press No to switch the tabs. pSee page 369 for storing/displaying personal data.

List tab

Phone number tab

Information

pIn Dual Mode of 2in1, you can switch between Number A and Number B by pressing

+Oo( ) from the Own Number display. “ ” appears for Number A, and “ ”

appears for Number B.

pWhen you replace a UIM with another one (2in1 contractor → 2in1 contractor) while

using 2in1, perform “2in1 function OFF” (see page 401) and then set “2in1 setting” to “YES”, or perform “Auto acquire No. B” (see page 370), to acquire the correct Number B. When you replace a UIM with another one ( perform “2in1 function OFF” as well to update the owner’s information to the correct one.

2in1 contractor → 2in1 non-contractor

Own Number display

Voice/Videophone Calls

Making Calls/Videophone Calls

About Videophone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Making a Call/Videophone Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Switching between a Voice Call and a Videophone Call. . . . . . . . . . 51

Using Call Records. . . . <Redial> <Dialed Calls> <Received Calls> 52

Using Chaku-moji . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Chaku-moji> 54

Notifying/Not notifying Your Phone Number by Call. . . . <186/184> 56

Sending Touch-tone Signals . . . . . . . . . . . . . . . . . . . . .<Pause Dial> 57

International Calls. . . . . . . . . . . . . . . . . . . . . . . . . . . <WORLD CALL> 58

Setting for International Calls . . . . . . . . <International Dial Assist> 59

Storing Numbers to be Added to the Beginning of a Phone Number

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Prefix Setting> 60

Making a Call with Specified Sub-address

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Sub-address Setting> 60

Setting Alarm for Reconnecting . . . . . . . . . . . .<Reconnect Signal> 60

Making Voice Clear According to Surrounding Noise

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .<Shikkari Talk> 61

Reducing Surrounding Noise to Make Voice Clear

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .<Noise Reduction> 61

Slowing Down the Other Party’s Speaking Speed . . . <Yuttari Talk> 61

Switching to Hands-free. . . . . . . . . . . . . . . . . . . . . . . . <Hands-free> 61

Using Hands-free Compatible Devices. . . . . . . <In-Car Hands-free> 61

Receiving Calls/Videophone Calls

Receiving a Call/Videophone Call. . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Switched between a Voice Call and a Videophone Call by the Other Party

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Setting Response of Key Operation for Answering Incoming Calls

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .<Answer Setting> 64

Setting Response for when Opening FOMA Phone during Ringing

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Setting when Opened> 64

Setting Response for when Closing FOMA Phone during a Call

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Setting when Closed> 64

Adjusting Earpiece Volume . . . . . . . . . . . . . . . . . . . . . . . . <Volume> 65

Adjusting Ring Volume . . . . . . . . . . . . . . . . . . . . . . . <Ring Volume> 65

When You Cannot or Could not Answer the Call

Putting an Incoming Call on Hold when You cannot Answer at Once

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <On Hold> 66

Putting a Call on Hold during a Call. . . . . . . . . . . . . . . . . .<Holding> 66

Setting Hold Tone . . . . . . . . . . . . . . . . . . . . . . . . . . <Set Hold Tone> 66

Using Public Mode (Drive Mode) . . . . <Public Mode (Drive Mode)> 67

Using Public Mode (Power Off) . . . . . . .<Public Mode (Power Off)> 67

If You could not Answer an Incoming Call . . . . . . . <Missed Calls> 68

Recording Voice/Video Messages when You cannot Answer the Call

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Record Message Setting> 69

Recording Voice/Video Messages when You cannot Answer the Call

during Ringing. . . . . . . . . . . . . . . . . . . . . . <Quick Record Message> 70

Playing Back/Erasing Record Messages/a Voice Memo/Videophone Record Messages/Movie Memos

. . . . .<Play/Erase Messages> <Play/Erase Videophone Messages> 70

Making Full Use of Videophone Calls

Using Chara-den . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Useful Functions for Videophone Calls. . . . . . . . . . . . . . . . . . . . . . . 72

Setting Videophone Hands-free . . . <Hands-free with Videophone> 74 Setting Image Quality for Videophone Calls . . <Visual Preference> 74 Changing Image Displays for Videophone Calls . . <Select Image> 75 Redialing as a Voice Call when a Videophone Call cannot be

Connected . . . . . . . . . . . . . . . . . . . . . . . <Voice Call Auto Redial> 75

Setting for Switching between a Voice Call and a Videophone Call

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Notify Switchable Mode> 76

Selecting Response to Incoming Videophone Calls during i-mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Videophone while Packet> 76

Connecting FOMA Phone to External Devices to Use Videophone

Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

About Videophone

Between the DOCOMO phones which support videophone calls, you can talk while viewing sent/received images. By default, the substitute image is displayed at the position of the sent image.

This FOMA phone has no inward-facing camera. Therefore, the image sent to the other party is a Chara-den image, still image, or image being shot by the outward-facing camera.

DOCOMO videophones conform to 3G-324M, standardized by the international standard 3GPP. You cannot connect to the videophone that uses a different format.

p3GPP (3rd Generation Partnership Project):

This is the regional standards organization for developing common technical specifications for third-generation mobile telecommunication systems (IMT-2000).

p3G-324M:

This is the international standard for the third generation of mobile videophones.

pP-06A supports only 64 kbps communication speed of the videophone.

You cannot talk on the videophone at 32 kbps communication speed.

Voice/Videophone Calls

■Display during videophone calls

…Received image (The other party’s image through the

camera or substitute image)

…Sent image (Substitute image or image through your

camera)

…Call duration …Status

: Voice sending/receiving (gray): Voice sending/

receiving failed : Image sending/receiving (gray): Image sending/

receiving failed

: Camera image sending :

Still image sending

: Chara-den talking

※1 When voice sending fails, the other party cannot hear your voice.

When voice receiving fails, you cannot hear the other party’s voice.

※2 When image sending fails, the sent image is not displayed at the other end.

When image receiving fails, the received image is not displayed.

When voice or image sending/receiving fails, it does not recover automatically. You need to make a videophone call again.

: Hands-free activated : Close-up

※1

: Landscape : Night Mode

: Chara-den Whole

※2

Action Mode

: Chara-den Parts Action

Mode

: DTMF Transmission

Mode







Making a Call/Videophone Call

Enter the other party’s phone number,

starting with the city code.

pWhen 27 or more digits are entered, the lower 26 digits

only are displayed.

pTo store an entered phone number in the Phonebook,

press m( ). Go to step 2 on page 82.

pEven when you are dialing within the same area, you

need to enter the city code before the phone number.

When Making a Voice Call

Press d or Oo().

p“ ” blinks during dialing, and lights during a call.



When Making a Videophone Call

Press l().

p“ ” blinks during dialing and lights during the call. pDuring a videophone call, you can press m() to

display the image through your camera at the other

party. To resume the substitute image, press

m( ) again.

The digital communication charging starts from this display.

Press h to end the call after talking.

Information

pIf you hear the guidance requesting your caller ID (see page 396), follow the steps of

“To notify your caller ID” on page 56 to enter “186” and redial.

pWhen an earphone/microphone (option) is connected, you can hear the other party’s

voice from the earphone. (See page 375)

pIf you close the FOMA phone during a call, the FOMA phone works in accordance

with the setting of “Setting when closed”. (See page 64)

pYou can press numeric keys to send touch-tone signals during a call. During a

Chara-den call, you need to switch to DTMF Transmission Mode. (See page 73)

pIn Dual Mode of 2in1, you can make a call after selecting Number A or Number B.

(See page 402)

Information

pYou can make a voice call also by pressing -d and then entering the party’s phone

number. If you enter a wrong number, press -h to clear the display and then redial.

pJust after purchase, Hands-free is automatically activated by “Hands-free

w/ V. phone” (see page 74). However, Hands-free is deactivated during Manner Mode regardless of “Hands-free w/ V. phone”.

pWhen you make a videophone call with substitute image, note that you will still be

charged for the digital communication, not the voice calls.

pIf you make a videophone call at 110/119/118 from the FOMA phone, it is

automatically dialed out as a voice call.

pThe international videophone call is available using the DOCOMO international call

service “WORLD CALL”. (See page 58)

Display during dialing

The other party’s name and icon are displayed if the party’s phone number and name are stored in the Phonebook. However, the image is not displayed even if it is stored in the Phonebook. pIf the same phone number is stored with multiple names in the Phonebook, the name

that comes first in the search order (see page 84) is displayed.

pThe phone number instead of the name is displayed when you make a call during

Personal Data Lock or to the party stored as secret data in the Phonebook.

If you entered a wrong phone number

Each time you press r, the digit on the far right is cleared. If you press and hold r for at least one second, all the digits are cleared and the Stand-by display returns.

pPress No to move the cursor to the digit you want to clear, and then press r to

clear it. To clear all the digits on and to the right of the cursor, press and hold r for at least one second.

Voice/Videophone Calls

If a videophone call could not be connected

The reason why it could not be connected is displayed. (The displayed reason might not be the same as the actual reason depending on the type of the other party’s phone and contract for network services.)

Messages Reasons

Check number, then redial Busy The other party is busy. (Depending on the receiver’s

Busy with packet transmission Out of service area/power off Set caller ID to ON Your caller ID is not notified. (when dialing “visualnet”, etc.) Your call is being forwarded

Voice/Videophone Calls

Redial using voice call The other party activates Call Forwarding Service but the

Upper limit has been exceeded Connection failed Please make your call from the i-mode web page

Connection failed Redial after setting “Activate” of “Caller ID notification” to

You have dialed a non-existent phone number.

phone, this message might be displayed during packet communication as well.) The packet communication is progress at the other end.

The other party’s phone is out of the service area or turned off.

During forwarding

forwarding destination phone does not support videophone calls. The upper limit for the plan with the limit function (Type Limit, Family Wide Limit) is exceeded.

You did not make a videophone call from the IP (Information Provider) site among i-mode official sites (at dialing to V-live).

“ON”. pThis may appear in the case other than above.

Auto-redialing

If “Voice call auto redial” is set to “ON”, and a videophone call is not connected, a voice call is automatically made. pVideophone calls cannot be connected to the phones that do not support the

videophone function, or to the phones that are out of the service area or turned off even if they are videophones. If you have set “Voice call auto redial” to “ON” and attempt to dial a phone that does not have the videophone function, the number will be redialed as a voice call. However, this operation might not work if you call the phone connected with ISDN-synchronous 64K or the ISDN videophone that does not support 3G-324M (as of February 2009), or if you dial the wrong number. Note that you could be charged for the communication.

Function Menu while Entering Phone Number

Function menu Operation/Explanation

Notify caller ID See page 56.

Prefix numbers See page 60.

Int’l dial assist See page 59.

Select image See page 75.

Multi number You can select a phone number to be notified to the other party.

Add to phonebook See page 82.

Compose message You can compose a mail message to send to the phone number

Chaku-moji See page 54.

(See page 400.)

set as the destination address. Go to step 3 on page 180.

Switching between a Voice Call and a Videophone Call

You (caller) can switch between a voice call and a videophone call. This function is available for the mobile phones that can switch between a voice call and a videophone call.

Switch from a Voice Call to a Videophone Call

When the other party’s phone has a function to switch between the calls, “ ” is displayed on your phone and you can switch from the voice call to videophone call.

During a voice callc()Change

pWhen you select an image

to be sent to the other

party, select “Select

image”. Go to step 2 of “Set

by Call” on page 75.

pWhen “Cancel” is selected,

the FOMA phone cancels

switching and returns to the

voice call.

pWhile switching, the voice

guidance is played back.

Switch from a Videophone Call to a Voice Call

When the other party’s phone has a function to switch between calls, you can switch from a videophone call to a voice call by selecting “CHG to voice call” from the Function menu.

During a videophone calli()

CHG to voice callYES

pSelect “NO” on the

confirmation display to stop switching and to resume the videophone call.

pWhile switching, the voice

guidance is played back.

Information

pYou can switch between a voice call and a videophone call repeatedly. pWhen i-mode or packet communication is in progress, the communication is

disconnected and then the voice call is switched to the videophone call.

pWhen packet communication is in progress at the other end, the message to the

effect that the communication cannot be switched is displayed and the voice call continues without switching to the videophone call.

pYou cannot switch from a voice call to a videophone call while “Multi calling” is

displayed during a call if you have signed up for Call Waiting Service.

pIt takes about five seconds to switch. Switching may take a longer time depending on

the radio wave conditions.

Depending on how the caller’s phone is working or on the radio wave conditions, switching between a voice call and a videophone call may fail and the connection may be cut off.

pIf you switch between a voice call and a videophone call during a call, the call duration

and call cost are counted respectively for each call. You are not charged while “Changing” is displayed.

pYou cannot switch between a videophone call and a voice call unless “Notify

switchable mode” on page 76 is set to “Indication ON” at the other end.

pWhen you switch from a videophone call to a voice call, Hands-free is deactivated.

Voice/Videophone Calls

Using Call Records

The FOMA phone can store the other party’s phone number and date/ time you have dialed or received. You can call back to the other party.

■Redial

Up to 30 records of dialed voice calls and videophone calls are stored in total, and the older record of dialing to the same phone number is deleted.

■Dialed Calls

Up to 30 records of dialed voice calls and videophone calls are stored in total, and up to 30 records of 64K data and packet com munications are stored in total as well. The older records of dialing to the same phone number are also retained.

■Received Calls

Up to 30 records of incoming voice calls and videophone calls are stored in total, and up to 30 records of 64K data and packet communications are stored in total as well. The older records coming from the same phone number are also retained. pWhen a call is switched between a voice call and a videophone call, the call that is

Voice/Videophone Calls

dialed/received first is stored.

pWhen more than 30 calls are dialed, the older records are automatically deleted. Even

if you turn off the FOMA phone, call records are not deleted.

pIn Dual Mode of 2in1, up to 60 redial items, 120 dialed call records, and 120 received

call records for Number A and Number B are stored in total.

■Icons for Redial, Dialed Calls, and Received Calls

※

Dialed and received calls/missed calls of voice call

※

Dialed and received calls/missed calls of videophone call

Voice/Video messages are recorded on Record Message

※

Dialed and received calls/missed calls of international call

Dialed and received calls/missed calls of international videophone

※

call

Dialed calls of 64K data communication

※

Received calls/missed calls of 64K data communication

Dialed calls of packet communication

※

Received calls/missed calls of packet communication

Received calls of 64K data communication and packet communication when no external device is connected

Received Chaku-moji message

Records with time difference corrected

Records for Number B (only in Dual Mode of 2in1)

※ The unchecked missed call icons are highlighted.

Use Redial/Dialed Calls

When Using Redial

Press Vo.

When Using Dialed Calls

mPhonebookDialed/recv. calls

Dialed calls

The list for call records is displayed. pPress m( ) to display the Sent Address list.

Select a call record.

The detailed display for the call record is displayed. pWhen the other party is stored in the Phonebook, the

phone number, name, and icon are displayed. If the same phone number is stored with multiple names in the Phonebook, the name and icon that come first in the search order (see page 84) are displayed.

For Redial

Use Received Calls

+m-2-4

Press Co.

pYou can display the Received Call list also by

mPhonebookDialed/recv. callsReceived calls

All calls or Missed calls.

All calls . . . . . . All the records including missed calls

Missed calls. . . The records of missed calls only

In Dual Mode of 2in1, the number of missed calls for

Number A and Number B is displayed respectively.

(If unchecked missed calls are found, the number of

them is displayed.)

pPress m( ) to display the Received Address list.

Received Call list

Select a received call record.

pThe other party’s phone number is displayed if it is

provided.

If this caller is stored in the Phonebook, the phone

number, name, and icon are displayed. If the same

phone number is stored with multiple names in the

Phonebook, the name and icon that come first in search

order (see page 84) are displayed.

If there is a call for packet communication, the sender’s

access point name (APN) is displayed.

When the other party’s phone number is not notified, the reason for no caller ID is

displayed.

pFor missed calls, the ring time is displayed on the right of the received date/time. pWhen a Chaku-moji message is received, it is displayed.

To make a call to a displayed redial item, dialed call record, or received call record

Press d to make a voice call. You can make a voice call also by pressing

Oo( ) from the detailed display. Press l( ) to make a videophone call.

Information

pYou can make a voice call to the most recently dialed or received number by pressing

-d from the Stand-by display and then +No.

Detailed Received

Call display

Information

pWhen you make/receive a call with an additional number of Multi Number, the stored

name for the additional number is displayed below the phone number on the detailed display. If you store a phone number for “Number setting” of “Multi number”, the phone number is displayed as well.

pEven if you make a voice call (or videophone call) to the phone number in a received

call record with a Chaku-moji message displayed, the received message is not sent.

pWhen a call comes in from a party who uses a dial-in phone number, a different

phone number might be displayed.

Function Menu while Redial/Dialed Calls/Received Calls is Displayed

Function menu Operation/Explanation

Notify caller ID See page 56.

Prefix numbers See page 60.

Int’l dial assist See page 59.

2in1 dial You can select a phone number to be notified to the other party in

Multi number You can select a phone number to notify the other party. (See

Chaku-moji See page 54.

Character size You can switch character sizes for the lists/detailed displays.

Add to phonebook See page 82.

Ring time

[Received Call list only]

Add desktop icon See page 109.

Compose message You can compose a mail message to send to the phone number

Dual Mode of 2in1. (See page 402)

page 400)

(See “Dialed/recv. calls” on page 112)

pYou can store the phone number in the Phonebook also by

pressing m( ) from the detailed display. Go to step 2 on page 82.

You can display the ring time for missed calls. Even if you have set “Missed calls display” of “Ring time” to “Not display”, the missed calls which stopped ringing within the ring start time and their ring times are displayed.

set as the destination address. Go to step 3 on page 180.

Voice/Videophone Calls

Function menu Operation/Explanation

Compose SMS You can compose an SMS message to send to the phone

Sent address

[Redial/Dialed Calls only]

Received address

[Received Calls only]

Delete this YES

Delete selected Put a check mark for redial items, dialed call records, or

Delete all Enter your Terminal Security CodeYES

Select image See page 75.

Voice/Videophone Calls

Information

pIf you execute “Delete all” from the Function menu of Redial/Dialed Calls, all records

in both Redial and Dialed Calls are deleted. Even if you execute “Delete this” or “Delete selected” of Redial, the records are not deleted from Dialed Calls and they are retained. To delete the dialed call records, delete them from the Function menu while “Dialed calls” is displayed.

number set as the destination address. Go to step 3 on page 225.

See page 210.

received call records to be deletedl()YES

<Chaku-moji>

Using Chaku-moji

When making a voice call or videophone call, you can send your text message to tell the subject during calling.

pFor details on Chaku-moji or compatible models, refer to DOCOMO web page or

“Mobile Phone User’s Guide [Network Services]”.

pThe sending end is charged, but the receiving end is not charged.

When a message is received

A Chaku-moji message is displayed below a caller. The Chaku-moji message is stored in Received Calls as well. pThe Chaku-moji message is displayed only during ringing. It

is not displayed during a call.

pEven when a Chaku-moji message comes in within the ring

start time set by “Ring time”, it is received and recorded in Received Calls.

pThe Chaku-moji message is displayed on the Private window when “Chaku-moji” of

“Called” on page 101 is set to “ON”.

pThe Chaku-moji message is not displayed during Lock All, Omakase Lock, or Personal

Data Lock. However, you can check the Chaku-moji message from Received Calls after the lock is released.

Store Messages

You can store up to 10 Chaku-moji messages in the Message list.

mServiceChaku-mojiCreate message

Highlight <Not stored> and press l() Enter a message.

pTo edit a stored message, highlight it and press l(). pYou can enter up to 10 characters regardless of whether they are pictographs,

symbols, or full-pitch/half-pitch characters.

Make a Call with a Message

Enter a phone number

bring up the detailed display of a Phonebook entry, redial item, dialed call record, or received call record.

i()Chaku-mojiDo the following operations.

Function menu Operation/Explanation

Create message You can create a Chaku-moji message just before dialing.

Select message From the Message list, you can select a stored message.

Sent messages From the Sent Message list, you can select a Chaku-moji

Press d or Oo().

pPress l( ) to make a videophone call. pThe Chaku-moji message being sent is displayed during dialing.

Information

pWhen a Chaku-moji message has arrived at the other party’s phone, “Transmission

completed” is displayed, and you are charged a transmission fee.

pWhen a Chaku-moji message does not arrive at the other party’s phone such as when

the other party’s phone is not a Chaku-moji compatible mobile phone or the call is not allowed by “Message disp. settings” at the receiving end, “Transmission failed” is displayed. In this case, you are not charged a transmission fee.

pDepending on the radio wave conditions, the transmission result may not be

displayed at the sending end even if a Chaku-moji message has arrived at the other party’s phone. In this case, you are charged a transmission fee.

pEven if you make a call sending a Chaku-moji message, the Chaku-moji message is

not displayed and you are not charged a transmission fee (the call is not recorded in Received Calls at the receiving end) when the other party’s phone is out of the service area, turned off, during Public Mode (Drive Mode), or the ring time for Record Message Setting is set to zero seconds. Also, the transmission result is not displayed at the sending end.

Enter a message.

pYou can enter up to 10 characters regardless of whether they

are pictographs, symbols, or full-pitch/half-pitch characters.

pThe Chaku-moji message created using this function is not

stored in the Message list.

Select a message.

message to be sent. Up to 10 sent Chaku-moji messages only are stored in the Sent Message list. If you send the same Chaku-moji message, the older one is deleted. When the number of sent Chaku-moji messages exceeds 10, the messages are deleted from the oldest one.

Select a sent message.

Information

pWhen a videophone call is not connected and automatically dialed as a voice call, the

Chaku-moji message is resent as well.

pYou cannot send/receive Chaku-moji messages overseas.

Detailed Sent Message

Up to 10 sent Chaku-moji messages are stored in Sent Messages, and you can check for the other party’s phone number and the date/time the Chaku-moji messages were sent. Older messages sent to the same phone number are also retained.

pIn Dual Mode of 2in1, up to 10 records for Number A and Number B can be displayed

in total.

mServiceChaku-moji

Sent messages

. . . . Chaku-moji message successfully sent

. . . . Chaku-moji message unsuccessfully sent

. . . . . . . Chaku-moji message for Number B (only in

pWhen the transmission result is not displayed, “ ” or “ ” is not

pDepending on the radio wave conditions, the transmission result might not be

Dual Mode of 2in1)

displayed.

displayed correctly.

Select a sent message.

pWhen the other party’s phone number is stored in the

Phonebook, the phone number, name, and icon are displayed.

Voice/Videophone Calls

Function Menu while Detailed Sent Message is Displayed

Function menu Operation/Explanation

Store You can store a sent Chaku-moji message in the Message list.

Delete this YES

Delete all Enter your Terminal Security CodeYES

Message Display Settings

You can set how incoming Chaku-moji messages are displayed.

mServiceChaku-mojiMessage disp. settings

Select an item.

Display all messages . . . . Displays Chaku-moji messages from all callers.

Numbers stored in PB . . .Displays Chaku-moji messages only from the callers

Voice/Videophone Calls

Calls with callerID. . . . . . .Displays Chaku-moji messages only from the caller

Hide all messages. . . . . . .Does not display Chaku-moji messages.

Information

pWhen you set to “Numbers stored in PB”, you cannot receive Chaku-moji messages

from the callers stored in the Phonebook B in A Mode of 2in1 (and vice versa).

Prefer Chaku-moji

You can set how your FOMA phone works for incoming Chaku-moji messages for when “Setting when opened” is set to “Answer”.

mServiceChaku-mojiPrefer Chaku-moji

ON or OFF

ON . . . . Does not answer by opening the FOMA phone during ringing, so you can

OFF . . . Answers by opening the FOMA phone during ringing.

<Not stored>

pYou can store also by pressing l().

stored in the Phonebook.

notifying his/her phone number.

check a Chaku-moji message.

<186/184>

Notifying/Not notifying Your Phone Number by Call

Set Caller ID Notification when Making a Call

Each time you dial out, you can set whether to notify your caller ID.

Enter a phone number

bring up the detailed display of a Phonebook entry, redial item, dialed call record, or received call record.

i()Notify caller ID

Don’t notify or Notify caller (OFF or ON)

pTo release “Notify caller ID”, select “Cancel prefix”. Whether to notify or not

follows the setting for “Activate” of “Caller ID notification”.

Set “Notify/Not Notify” by Entering “186/184”

You can select whether to notify the other party of your phone number also by entering “186”/“184” before the other party’s phone number.

To notify your caller ID

186→Destination phone numberd or Oo()

pPress l( ) to make a videophone call.

Not to notify your caller ID

184→Destination phone numberd or Oo()

pPress l( ) to make a videophone call.

Information

pWhen you make a call and hear the guidance requesting your caller ID (see

page 396), follow the steps of “To notify your caller ID” to enter “186” and redial.

pYou cannot set “Caller ID notification” while “ ” is displayed.

+m-8-4

Sending Touch-tone Signals

You can send touch-tone signals from your FOMA phone to use services such as reserving tickets, checking bank balance, etc.

Store Pause Dial

You need to store a number string to be sent as a touch-tone signal in the Pause Dial list. If you have inserted a pause (p), you can send a number string breaking at the point where the pause is inserted.

m

pWhen a number string is already stored, it is displayed. pTo delete a stored pause dial, press i( ) and select “Delete”, then select

“YES”.

Enter a number string.

pEnter the pause (p) by pressing and holding a for at least one second. pYou can use only 0 through 9, s, a to enter a number string and

the pause (p).

pYou can enter up to 128 digits. pYou cannot enter a pause (p) at the beginning and end of a number string, or

enter it consecutively.

SettingsOther settingsPause dial

l

()

Send Pause Dial

m

SettingsOther settingsPause dial



Enter a phone number

A voice call is made. Once the line is connected, a number string stored in Pause Dial is displayed up to the first pause (p). pWhen the other party’s phone number is stored in the Phonebook, you can

retrieve it selecting from the Search Phonebook display by pressing Bo.

pYou can search for the phone number also from Received Calls by pressing Co

or from Redial by pressing Vo.

d

or Oo()

Oo

()

Check that the line is connectedd or Oo()

A number string up to the first pause (p) is sent, and a number string up to the next pause (p) is displayed. A number string up to the pause (p) is sent each time you press d or

Oo().

When you have finished sending the last number, the “Talking” display appears. pTo send multiple pieces of a number string at a time, press and hold Vo for at

least one second, and select “Send at one time”.

Information

pDuring a call, you can send a number string also by displaying the Function menu of

the Pause Dial display.

pSome devices on the receiving end cannot receive signals. pYou cannot send a number string with pauses during a videophone call.

Voice/Videophone Calls

International Calls

WORLD CALL is the international call service available from DOCOMO mobile phones. When you have signed up for FOMA service, you have contracted to use “WORLD CALL” (except those who have applied not to use it).

pYou can call about 240 countries and regions. pThe WORLD CALL charges are added to your monthly FOMA bill. pThe application/monthly fee is free of charge. pThe service is not available with some billing plans. pContact “docomo Information Center” on the back page of this manual for inquiries

about WORLD CALL.

pWhen using international carriers other than DOCOMO, contact them. pThe caller ID might not be notified, or might not be displayed correctly depending on

the carrier. In this case, you cannot make a call by using Received Calls.

About international videophone calls

Voice/Videophone Calls

You can make international videophone calls to the other party who uses a FOMA phone or videophone-compatible terminal of specific 3G carriers overseas. Press l() instead of d or Oo( ) in the steps of “Enter a Phone Number to Make an International Call”. (See page 58) pFor the information about connectable countries and telecommunications carriers, refer

to the DOCOMO Global Service web page.

pImages sent from the other party may blur on your FOMA phone or you may not be

able to connect, depending on the other party’s phone used for the international videophone call.

Enter a Phone Number to Make an International Call

Enter numbers in order of 010→country/area code

→area code (city code)→destination phone number

d or Oo()

pYou can make an international call also by entering 009130→010→country/area

code→area code (city code)→destination phone number.

When the area code (city code) begins with “0”, enter it except for the “0”. However, include “0” when making a call to some countries or regions such as Italy.

pPress l( ) to make an international videophone call.

Use “+” to Make an International Call

When you enter a phone number for dialing or storing it in the Phonebook, press and hold 0 for at least one second to enter “+”. You can use “+” to make international calls without entering an international call access code.

pIf you set “Auto assist setting” of “Int’l dial assist” to “ON”, an international call access

code of “IDD prefix setting” is automatically entered.

0(for at least one second)

Enter numbers in order of country/area code

→area code (city code)→destination phone number

d or Oo()Dial

When the area code (city code) begins with “0”, enter it except for the “0”. However, include “0” when making a call to some countries or regions such as Italy.

pPress l( ) to make an international videophone call. pWhen you select “Dial with orig. No.”, you can make a call without adding an

international call access code.

International Dial Assist

You can make a call adding a country/area code or international call access code to a phone number. (Except for some countries and regions, if the phone number starts with “0”, the “0” at the beginning is automatically deleted.)

Enter a phone number

bring up the detailed display of a Phonebook entry, redial item, dialed call record, or received call record.

i()Int’l dial assist

Select a country/area nameSelect a name d or Oo()

pPress l( ) to make an international videophone call. pWhen the beginning of the phone number is “+”, you can select only an

international call access code.

pWhen “Japan” is selected as a country/area name, the display for selecting a

name is not displayed.

Setting for International Calls

Auto Assist Setting

You can set whether to replace “+” at the beginning of a phone number with an international call access code for when you make an international call from Japan.

mSettingsNetwork settingInt’l dial assist

Auto assist settingON or OFF Select a country/area nameSelect a name.

pWhen no country/area code or international call access code is stored, the

confirmation display appears asking whether to store it. Select “YES” and go to

step 2 of “Country/Area Code” on page 59 for a country/area code, and go to

step 2 of “IDD Prefix Setting” on page 59 for an international call access code.

Country/Area Code

You can store up to 27 country/area codes to be added for making international calls from overseas.

mSettingsNetwork settingInt’l dial assist

Country/Area Code Highlight <Not recorded> and press l().

pIf you select a stored country/area name, you can check the stored contents.

Enter a country/area name Enter a country/area code.

pYou can enter a country/area name of up to 8 full-pitch/16 half-pitch characters. pYou can enter a country/area code of up to 5 digits. But you cannot use #, :, and

IDD Prefix Setting

You can store up to three international call access codes to be added to the beginning of a phone number for making an international call.

mSettingsNetwork settingInt’l dial assist

IDD prefix setting Highlight <Not recorded> and press l().

pIf you select the stored item, you can check the stored contents.

Enter a nameEnter an international call access code.

pYou can enter a name of up to 8 full-pitch/16 half-pitch characters. pYou can enter an international call access code of up to 16 digits.

Function Menu while Country/Area Code /IDD Prefix Setting is Displayed

Function menu Operation/Explanation

Edit Go to step 2 of “Country/Area Code” on page 59 for Country/Area

Code, and go to step 2 of “IDD Prefix Setting” on page 59 for IDD Prefix Setting. pYou can edit the item also by pressing l().

Voice/Videophone Calls

Function menu Operation/Explanation

Delete this YES

Delete all Enter your Terminal Security CodeYES

Information

pYou cannot delete the country/area code or international call access code set by

“Auto assist setting”.

Storing Numbers to be Added to the Beginning of a Phone Number

You can store prefix numbers such as international call access codes or “186”/“184” and add them to the phone number for dialing. You can store up to seven prefix numbers.

Voice/Videophone Calls

mSettingsNetwork settingPrefix setting

Highlight <Not recorded> and press l().

pIf you select a stored prefix, you can check the stored contents. pTo delete a stored prefix, press i( ) and select “Delete this” or “Delete all”

then select “YES”. If you select “Delete all”, you need to enter your Terminal Security Code.

Enter a nameEnter a prefix number.

pYou can enter a name of up to 8 full-pitch/16 half-pitch characters. pYou can enter a prefix number of up to 16 digits. The keys for entry are limited to

0 through 9, s and a.

Prefix Numbers

You can add a prefix number to the beginning of phone number when you make a call.

Enter a phone number

bring up the detailed display of a Phonebook entry, redial item, dialed call record, or received call record.

i()Prefix numbersSelect a name

d or Oo()

pPress l( ) to make a videophone call.

<Sub-address Setting>

Making a Call with Specified Sub-address

You can set whether to regard the numbers after “:” of a phone number as a sub-address to access the specified phones or data terminals.

pThe sub-address is a number assigned to identify each ISDN terminal connected to an

ISDN line. It is also used for selecting contents on “V-live”.

mSettingsOther settingsSub-address setting

ON or OFF

Information

pEven if you set “Sub-address setting” to “ON”, “:” at the top of phone numbers and

“:” immediately after the prefix number or “186”/“184” are not regarded as sub-address mark-off symbols.

+m-7-7

Setting Alarm for Reconnecting

You can set an alarm that sounds until a voice call or videophone call is reconnected after disconnected owing to bad radio wave conditions.

mSettingsTalkReconnect signal

Select an alarm.

Information

The reconnectable time differs depe nding on the usage status and radio wave conditions. An estimate is about 10 seconds and the call charge is applied also for that duration.

pWhile you are disconnected, no sound is transmitted to the other party.

Making Voice Clear According to Surrounding Noise

The volume of the other party’s voice is turned up according to the surrounding noise during a call. This setting is effective only when the other party's voice is output from the earpiece.

mSettingsTalkShikkari TalkON or OFF

Reducing Surrounding Noise to Make Voice Clear

The noise sent to the other party is reduced according to the surrounding noise during a call.

mSettingsTalkNoise reductionON or OFF

+m-7-6

Slowing Down the Other Party’s Speaking Speed

During a voice callm()

When Yuttari Talk is activated, “ ” is displayed. pPress m( ) again to return to the normal speed.

Information

pYuttari Talk is effective only for during a voice call. The speaking speed returns to

normal one when you end the call, switch calling parties during Multi calling, or switch from the voice call to a videophone call.

pYou cannot set Yuttari Talk while Omakase Lock or Lock All is activated.

<Hands-free>

Switching to Hands-free

When you switch to Hands-free, sound such as the other party’s voice is audible over the speaker.

During a call, dialing, or connectingd

When Hands-free is activated, “ ” is displayed.

pPress d again to deactivate Hands-free. pThe sound volume during a Hands-free call follows the setting specified by

“Volume” (earpiece volume).

pYou can switch to Hands-free even during Manner Mode. Also, you will still hear

voice through the speaker even when you activate Manner Mode during a Hands-free call.

Information

pWhile an earphone/microphone (option) is connected, you cannot hear voice through

the speaker even if you switch to Hands-free.

pKeep the FOMA phone well away from your ear during a Hands-free call. Otherwise

you could affect or damage your hearing.

pTalk into the FOMA phone within a distance of about 50 cm.

<In-Car Hands-free>

Using Hands-free Compatible Devices

You can make or receive voice calls from a Hands-free compatible device such as In-Car Hands-Free Kit 01 (option) or a car navigation system by connecting with your FOMA phone.

pConnect using a cable (USB connection):

To use/charge via the In-Car Hands-Free Kit 01 (option), you need to have the FOMA In-Car Hands-Free Cable 01 (option).

※For how to operate Hands-free compatible devices, refer to the respective instruction

manuals.

Voice/Videophone Calls

Information

pTo connect using a cable (USB connection), set “USB mode setting” to

“Communication mode”.

p“ ” appears while you are talking or communicating using a USB Hands-free

compatible device.

p“ ” might appear while the FOMA phone is connected to a USB Hands-free

compatible device, and “ ” while “USB mode setting” is set to “microSD mode”, depending on the Hands-free device connected.

pThe display or ring tone for incoming calls follows the settings of the FOMA phone. pWhen the sound is set to output from a Hands-free compatible device, the ring tone

sounds from that device even when Manner Mode is activated or “Ring volume” of the FOMA phone is set to “Silent”.

pThe receiving operation in Public Mode (Drive Mode) works in accordance with the

“Public (Drive) mode” setting.

pThe receiving operation while Record Message is activated follows the setting of

“Record message setting”.

pWhen the sound is set to output from the FOMA phone, the FOMA phone works in

Voice/Videophone Calls

accordance with “Setting when closed” if it is closed during a call. When the sound is set to output from a Hands-free device, the communication state does not change regardless of “Setting when closed” even if you close the FOMA phone.

Receiving a Call/Videophone Call

When you receive a call, the ring tone

sounds and the Call/Charging indicator flickers.

pTo vibrate the FOMA phone for incoming calls, set

“Phone” or “Videophone” of “Vibrator” to other than “OFF”.

pWhen receiving a videophone call, “Incoming V.phone”

is displayed.

p“ ” is displayed at the upper left of the phone

number for incoming international calls.

Chaku-moji message

(See page 54)

For Answering a Voice Call

Press d or Oo( ) to answer the call.

For Answering a Videophone Call

Press d

or Oo()

to answer

the videophone call.

The substitute image is sent to the other party. pPress m during a call to switch between the substitute

image and image through your camera for sending to the other party.

Press h to end the call after talking.

Information

pIf you close the FOMA phone during a call, the FOMA phone works in accordance

with the setting of “Setting when closed”. (See page 64)

Information

pYou might hear beeps (in-call ring tone) during a call.

If you have signed up for any of Voice Mail Service, Call Waiting Service, or Call Forwarding Service and set “Arrival call act” to “Answer”, the beeps (in-call ring tone) will sound for another incoming call, enabling you to do the following operations: Voice Mail Service

. . . . Transfer the call to the Voice Mail Service Center. (See page 391)

Call Waiting Service

. . . . Put your current call on hold and answer the incoming call. (See page 392)

Call Forwarding Service

. . . . Transfer the call to the registered forwarding destination. (See page 395)

pYou can set “Reject unknown” not to accept calls from the phone numbers that are not

stored in the Phonebook.

pWhen “Answer setting” is set to “Any key answer”, the call is placed on hold if you

answer the call by pressing .< with the FOMA phone closed. If you have set “Setting when closed” to “No tone” or “End the call”, the other party hears nothing, and if you have set “Setting when closed” to “Tone on”, the call hold tone is played back. You can start talking by opening the FOMA phone.

pJust after purchase, Hands-free is automatically activated during a videophone call as

“Hands-free w/ V. phone” has been set to “ON”. (See page 74) However, Hands-free is deactivated during Manner Mode regardless of “Hands-free w/ V. phone”.

pEven if Call Forwarding Service is set to “Activate”, the call is not forwarded unless the

forwarding destination is a phone compatible with the videophone conforming to 3G-324M (see page 48). Check the phone you are forwarding the call to and then activate the service. The videophone caller does not hear the guidance to the effect that the call is forwarded. (The message to the effect that the call is to be forwarded appears, depending on the receiver’s FOMA phone.)

pIf a videophone call comes in from the phone number to be rejected by Nuisance Call

Blocking Service, the video guidance for Call Rejection is played back and the call is disconnected.

Display for incoming calls

When a caller’s phone number is provided

If you store the caller’s name, phone number, and image in the Phonebook, the name, phone number, and icon (or image) are displayed. pIf the same phone number is stored with multiple names in the Phonebook, the name

that comes first in the search order (see page 84) is displayed.

pThe phone number but not the name is displayed during Personal Data Lock. pFor a forwarded call, the forwarder’s phone number is displayed below the caller. (It

might not be displayed in the case of some forwarders.)

pWhen you receive a call to an additional number of Multi Number, the stored name for

the additional number is displayed below the caller. (With a forwarded call, you can press c( ) to switch to display of the forwarder.)

When a caller’s phone number is not provided

The reason for no caller ID is displayed. (See page 125)

Function Menu while a Call is Ringing

Function menu Operation/Explanation

Call rejection You can disconnect the call without answering.

Call forwarding See page 395.

Voice mail See page 391.

Switched between a Voice Call and a Videophone Call by the Other Party

When you have set “Notify switchable mode” to “Indication ON”, a caller (the other party) can switch between a voice call and a videophone call. When the caller (the other party) switches between a voice call and a videophone call, the message telling that the call is being switched is displayed, the voice guidance is played back, and then the call is switched.

pYou (receiving end) cannot switch between a voice call and a videophone call.

Voice/Videophone Calls

+m-5-8

Setting Response of Key Operation for Answering Incoming Calls

You can set to start talking (Any key answer) or to stop the ring tone (Quick silent) by pressing a key besides d, Oo, m (for videophone call) for when a call comes in.

mSettingsIncoming callAnswer setting

Select a key operation.

Any key answer

You can start talking by pressing any key shown below:

d, Oo, 0 through 9, a, s, r, m, c※2,

※1

Voice call

pWhen receiving a videophone call, you can start talking by pressing d, Oo or

Voice/Videophone Calls

Quick silent

The following are the keys you can press to stop the ring tone, vibrator or voice guidance: When “Setting when opened” is set to “Keep ringing”, you can open the FOMA phone to stop the ring tone, vibrator or voice guidance. Even if you stop it, the other party still hears a calling tone.

Voice call※10 through 9, a, s, r, m, c※2, No, <

Videophone call

pAfter you stop the ring tone, vibrator or voice guidance, you can start talking by

pressing d, Oo, m (for videophone call).

OFF

You can start talking by pressing a key shown below:

Voice call Videophone call

※1 You can activate Any Key Answer or Quick Silent also by pressing l when

※2 While “ ” is displayed, you cannot start talking or stop the ring tone,

No, <

0 through 9, a, s, r, c※2, No, <

d, Oo

five record messages have already been recorded.

vibrator or voice guidance.

Information

pWhile an earphone/microphone (option) is connected, you can press the switch to

start talking, regardless of “Answer setting”. (See page 376)

Setting Response for when Opening FOMA Phone during Ringing

mSettingsIncoming callSetting when opened

Select an incoming typeKeep ringing or Answer

Information

pIf you receive a videophone call with “Answer” set, the still image set for “Substitute

image” of “Select image” is sent to the other party.

+m-1-8

Setting Response for when Closing FOMA Phone during a Call

mSettingsTalkSetting when closed

Select an item.

No tone . . . . . . . The voice is muted. The hold tone does not sound. The setting is

Tone on. . . . . . . The other party hears the hold tone set for “Holding tone” of “Set

End the call . . . The call is finished. This is the same operation as pressing h

Speaker ON or Speaker OFF

Speaker ON . . . . The hold tone sounds from the speaker.

Speaker OFF . . . The hold tone does not sound from the speaker.

completed.

hold tone” while the FOMA phone is closed.

during a call. The setting is completed.

Information

pThis function is disabled when you set “Headset mic. setting” to “Headset

microphone” and an earphone/microphone (option) is connected. The communication state does not change even if you close the FOMA phone during a voice call. If you close the FOMA phone during a videophone call, the substitute image is sent to the other party with the line connected.

pIf you close the FOMA phone during a videophone call with “No tone” set, the

substitute image is sent to the other party. When “Tone on” is set, the still image set for “Holding” of “Select image” is sent.

pIf you set to “No tone” or “Tone on”, “Holding” is displayed on the Private window

when the FOMA phone is closed.

Adjusting Earpiece Volume

mSettingsTalkVolumeUse Bo or </> to

adjust the earpiece volume.

Adjust the earpiece volume to Level 1 (minimum) through Level 6 (maximum). pDuring a call or calling, you can press Bo or </> to adjust the volume, and

while entering phone number, you can press and hold Bo(for at least one

second) to adjust it. Press Bo or </> within two seconds to adjust it.

Information

pThe earpiece volume adjusted during a call is retained even after the call ends. pWhen you adjust the earpiece volume, the sound volume during a Hands-free call is

also adjusted.

+m-5-0

Adjusting Ring Volume

You can adjust the ring volume for incoming calls and mail.

mSettingsSoundRing volume

Select an incoming type Use Bo to adjust the volume.

pFollowing icons are displayed on the Stand-by display while the ring volume is set

to “Silent”:

: The ring volume for voice calls or videophone calls is “Silent”.

: The ring volume for mail, chat mail or Messages R/F is “Silent”.

: The ring volume for voice calls or videophone calls is “Silent” and the ring

volume for mail, chat mail, or Messages R/F is “Silent”.

pIf you have set “Step”, the ring tone is silent for about three seconds, and then the

volume steps up every three seconds, from Level 1 through Level 6.

pDuring ringing of a voice call or videophone call, you can adjust the ring volume

also by pressing Bo or by pressing and holding </> for at least one second. However, you cannot adjust the ring volume in the following cases:

・When Ring Volume is set to “Step” ・When “Answer setting” is set to “Quick silent” and you stop the ring tone or

voice guidance

・During Manner Mode ・When a call is cut off within the ring start time specified by “Ring time”

Voice/Videophone Calls

Putting an Incoming Call on Hold when You cannot Answer at Once

During ringingh

The FOMA phone makes three rapid beeps for confirmation and the call is put on answer-hold (On Hold). pThe confirmation tone does not sound during Manner Mode or when “Ring

volume” is “Silent”.

pThe other party hears the hold tone set for “On hold tone” of “Set hold tone”. For

videophone calls, the still image set for “On hold” of “Select image” is displayed.

Press d or Oo( ) to release hold and answer

the call.

pIf “Answer setting” is set to “Any key answer”, you can release hold of voice calls

by pressing any key of 0 through 9, a, s, r, m, c, Mo,

Voice/Videophone Calls

<, >, l, or i.

pIf a videophone call is on hold and you press d or Oo( ) to release

hold, the substitute image is sent.

Information

pThe caller is charged for the call even during answer-hold (On Hold). pIf you press -h during answer-hold (On Hold), the call will be disconnected.

Putting a Call on Hold during a Call

During a callOo ()

pThe other party hears the hold tone set for “Holding tone” of “Set hold tone”. For

videophone calls, the still image set for “Holding” of “Select image” is displayed.

pYou can put the call on hold by closing the FOMA phone during the call if you

have set “Setting when closed” to “Tone on”.

Press d or Oo( ) to release hold and answer

the call.

pIf a videophone call is on hold and you press d or Oo( ) to release

hold, the substitute image is sent.

pIf you have set “Setting when closed” to “Tone on” and put the call on hold by

closing the FOMA phone, open the FOMA phone or connect an earphone/ microphone (option) to answer the call. If you connect an earphone/microphone to answer the videophone call, the substitute image is sent to the other party.

Information

pThe caller is charged for the call even while the call is on hold. pIf a new call comes in while the current call is put on hold, the hold (Holding) is

released.

Setting Hold Tone

You can set the guidance the other party hears during on hold.

mSettingsTalkSet hold tone

On hold tone or Holding toneSelect a hold tone.

Tone 1/2. . .The caller hears the pre-installed guidance in Japanese. JESU JOY OF MAN’S

. . . . . . . . . . .The caller hears the melody. You can set this for “Holding tone” only.

Voice announce

. . . . . . . . . . .The caller hears the sound recorded by “Voice announce”. If it has

pPress l( ) to play back a hold tone. Press r to end the demo

not been recorded, this is not displayed.

playback.

Using Public Mode (Drive Mode)

Public Mode is an auto-answer service that puts importance on manners in public spaces. Once you activate Public Mode, the guidance is played back telling that you cannot answer the call as you are currently driving or in a place (a train, bus, movie theater, etc.) where you should refrain from answering the call. Then the call is disconnected.

Press and hold a for at least one second.

Public Mode is activated and “ ” is displayed. When a call comes in, the guidance “The person you are calling is currently driving or in an area where cell phone should not be used. Please try again later.” is played back for incoming calls. pTo deactivate Public Mode, perform the same operation. Then, Public Mode is

deactivated and “ ” disappears.

Information

pYou can activate/deactivate Public Mode only from the Stand-by display. You can

activate/deactivate Public Mode even when “ ” is displayed.

pYou can make calls as usual even during Public Mode. pIf you make an emergency call at 110/119/118, Public Mode is released. pWhen Public Mode and Manner Mode are activated simultaneously, Public Mode has

priority.

pIf a “User unset” call comes in while “Caller ID request” is set to “Activate”, the Caller

ID Request guidance is played back. (The Public Mode guidance is not played back.)

pYou cannot use this function during data communication.

When Public Mode (Drive Mode) is activated

・Even when a call comes in, the ring tone does not sound. The “Missed call” icon

appears on the display and the call is stored in “Received calls”. The guidance is played back to the caller to the effect that you are currently driving or in an area where mobile phones should not be used. Then the call is disconnected. However, when the power is off or “ ” is displayed, the caller hears the out-of-service area guidance instead of the Public Mode guidance.

・The ring tone does not sound and the Call/Charging indicator does not flicker even

when mail or a message comes in. In addition, the set vibrator does not work.

・The ring tone for 64K data communication, alarm tone, and charging confirmation tone

do not sound, and a melody while an i-αppli program is running is not played back.

・The tickers of i-Channel are not displayed. ・See page 68 for how Public Mode (Drive Mode) and each network service work for

incoming calls when they are simultaneously activated.

Using Public Mode (Power Off)

Public Mode (Power Off) is an auto-answer service that puts importance on manners in public spaces. Once you activate Public Mode (Power Off), the guidance is played back telling that you cannot answer the call as you are currently in a place (hospital, airplane, around priority seat in a train, etc.) where use is prohibited. Then the call is disconnected.

Enter “:25251”d

Public Mode (Power Off) is set. (Nothing is changed on the Stand-by display.) After setting Public Mode (Power Off) and turning off the power, the guidance “The person you are calling is currently in an area where use is prohibited. Please try again later.” is played back for incoming calls.

pTo release Public Mode (Power Off), dial “:25250”. pTo check the setting for Public Mode (Power Off), dial “:25259”.

Voice/Videophone Calls

When Public Mode (Power Off) is activated

The setting stays activated until you dial “:25250” to deactivate Public Mode (Power Off). You cannot deactivate the setting just by turning on the power. The guidance is played back to the caller telling that you are currently in a place where you should turn off the power. Then the call is disconnected. The Public Mode (Power Off) guidance is played back even when you are out of the service area or out of reach of radio waves.

・See page 68 for how Public Mode (Power Off) and each network service work for

incoming calls when they are simultaneously activated.

■The receiving operation during Public Mode (Drive Mode/Power Off)

Service Responses to Incoming Voice Calls

Voice Mail Service

Call

Voice/Videophone Calls

Forwarding Service

Nuisance Call Blocking Service

Plays back the Public Mode guidance,

※

and then the call is connected to the Voice Mail Service Center.

Plays back the Public Mode guidance, and then the call is forwarded to the

※

forwarding destination. Whether the guidance is played back or not depends on the guidance setting of Call Forwarding Service. If “Plays guidance” is set, plays back the Public Mode guidance. If “Does not play guidance” is set, does not play back the guidance. For the call from the phone number registered to be rejected, plays back the Call Rejection guidance, and then the call is disconnected.

Responses to Incoming

Videophone Calls

Does not play back the video guidance for Public Mode, and the call is connected to the Voice Mail Service Center. Does not play back the video guidance for Public Mode, and the call is forwarded to the forwarding destination. If the destination does not support videophone calls, the call is disconnected.

For the call from the phone number registered to be rejected, plays back the video guidance for Call Rejection, and then the call is disconnected.

Service Responses to Incoming Voice Calls

Caller ID Display Request Service

※When the ring time is set to 0 seconds, the FOMA phone is out of the service area, or

For the caller without a caller ID, plays back the Caller ID Request guidance, and then the call is disconnected. For the caller with a caller ID, plays back the Public Mode guidance, and then the call is disconnected.

the power is off, the Public Mode guidance is not played back, but Voice Mail Service or Call Forwarding Service works. Note that in this case the call is not notified by the “Missed call” icon and not stored in “Received calls”.

Responses to Incoming

Videophone Calls

For the caller without a caller ID, plays back the video guidance for Caller ID Request, and then the call is disconnected. For the caller with a caller ID, plays back the video guidance for Public Mode, and then the call is disconnected.

If You could not Answer an Incoming Call

When you could not answer calls (Missed calls), the “Notification icon” appears on the Stand-by display. You can check Received Calls by selecting the icon.

OoOo()

pPress h or r to

return to the former display.

pWhen multiple icons are

found, use Mo to highlight an icon and press

Oo().

pSee page 31 for when the FOMA phone is closed.

Notification icon

+m-5-5

Recording Voice/Video Messages when You cannot Answer the Call

By activating Record Message, you can play back an answer message to incoming calls and record callers’ voice/video messages when you cannot answer them even if you have not signed up for Voice Mail Service. You can record up to five messages for voice calls and up to two messages for videophone calls. Each message can be recorded for up to 20 seconds.

Activate Record Message

mLifeKitRec. msg/voice memo

Record message settingON or OFF Select an answer message.

pPress l( ) to play back the answer message. Press r to end the

demo playback.

pWhen “Japanese 1”, “Japanese 2”, or “English” is set, a beep sounds after

playing back the answer message to the other party. If “Voice announce” is set,

the beep does not sound.

Enter a ring time (seconds).

pEnter from “000” through “120” in three digits. pYou cannot set the same ring time for Auto Answer Setting and Record Message

Setting. Set a different time for each.

pWhile Record Message is activated, “ ”〜“ ” (the number of recorded

messages for voice calls) and “ ”〜“ ” (the number of recorded messages

for videophone calls) are displayed.

Incoming calls when Record Message Setting is set to “ON”

The ring time

elapses

Incoming Call Playing back the

For videophone calls, the still image set for “Preparing” of “Select image” is displayed on the other party’s display while playing back the answer message, and the still image set for “Record message” of “Select image” is displayed while recording. pTo answer a call while the answer message is being played

back or a voice/video message is being recorded, press d or Oo(). For videophone calls, press d or Oo( ) to send the substitute image. You can answer a call also by pressing the switch on an earphone/microphone (option). For videophone calls, the substitute image is sent to the other party.

Information

pRecord Message does not work when “ ” is displayed. pWhen Public Mode (Drive Mode) and Record Message are simultaneously activated,

the former has priority and the latter does not work.

pThe priority order of answer messages is as follows: “Setting for Phonebook entry” →

“Group setting” → “Record message setting”.

pIf “Voice announce” selected as an answer message is deleted, the answer message

will be set to “Japanese 1”.

answer message

Recording a voice/

video message

Displaying an icon on the

desktop (See page 107)

Voice/Videophone Calls

Information

pWhen Voice Mail Service or Call Forwarding Service is set at the same time as

Record Message, the priority depends on the ring time set for Voice Mail Service or Call Forwarding Service. To give Record Message priority, set the ring time for Record Message Setting shorter than that for Voice Mail Service or Call Forwarding Service. Even when you do this, Voice Mail Service or Call Forwarding Service works if there are already five record messages for voice calls and two record messages for videophone calls.

pYou cannot receive a call from a third party while a voice/video message is being

recorded. The third party will hear the busy tone.

Recording Voice/Video Messages when You cannot Answer the Call during Ringing

Even if a call comes in while Record Message is not activated, you can record the caller’s voice/video message just for that incoming call.

Voice/Videophone Calls

During ringingl() or >

Manner Mode is also activated. The caller will hear the answer message and then can leave you a voice/video message. pRecord Message does not work when five messages for voice calls and two

messages for videophone calls have already been recorded. Only Manner Mode is set when you operate by pressing >.

pWhen “Side keys guard” is set to “ON”, you cannot activate Record Message or

Manner Mode by pressing > with the FOMA phone closed.

+m-5-5

Playing Back/Erasing Record Messages/a Voice Memo/Videophone Record Messages/Movie Memos

Play Back/Erase Record Messages/a Voice Memo

mLifeKitRec. msg/voice memo

Play/Erase msg. Select a record message or voice

memo.

A beep sounds and playback starts. pOn the Record Message list, recorded items are

indicated by “★”.

pIt is played back at the volume set for “Volume”

(earpiece volume).

pWhen playback ends, a double-beep sounds and the message “Playing” is

cleared from the display.

pThe date and time the message/memo was recorded are displayed during

playback. When a caller’s phone number is provided, it is displayed. If the caller is stored in the Phonebook, his/her name is also displayed. However, the name is not displayed and the phone number only is displayed in the following cases:

・When you play back a record message from the caller stored as secret data in

Normal Mode

・When you play back a record message for Number A in B Mode (or vice versa)

while using 2in1

pIf the caller’s phone number is displayed during playback, you can make a voice

call to that phone number by pressing d. Press l( ) to make a videophone call.

To play back using .>

From the Stand-by display, press > to play back the latest record message. When record messages are not recorded, a voice memo is played back.

Record Message list

To skip to next message

Each time you press > during playback, messages are played back in the following order: the next new record message → the oldest record message → a voice memo.

To cancel playback midway

Press Oo() or r.

Play Back/Erase Videophone Record Messages/Movie Memos

mLifeKitRec. msg/voice memo

Play/Erase VP msg. Select a videophone record message

or movie memo.

pOn the Videophone Record Message list, recorded

items are indicated by “★”.

pIt is played back at the same volume of the playback

sound of i-motion movies.

pThe date and time the message/memo was recorded

are displayed during playback.

Videophone Record

Message list

To play back using .>

From the Stand-by display, press and hold > for at least one second to play back the latest videophone record message. When videophone record messages are not recorded, the latest movie memo is played back.

To cancel playback midway

Press Oo() or r.

Function Menu of the Record Message List/Videophone Record Message List

Function menu Operation/Explanation

Play You can play back the message.

Erase this YES

pYou can erase the message/memo also by pressing

i( ) during playback.

Function menu Operation/Explanation

Erase rec. msg. You can erase all record messages from the Record Message

Erase movie memo

[Videophone Record Message list only]

Erase all You can erase all record messages and a voice memo from the

list, and can erase all videophone record messages from the Videophone Record Message list.

YES

You can erase all movie memos.

YES

Record Message list, and can erase all videophone record messages and movie memos from the Videophone Record Message list.

YES

Using Chara-den

You can set up for sending a Chara-den image to the other party.

pSee page 307 for Chara-den images.

Set by Call

You can set a Chara-den image to be sent to the other party for making a videophone call.

Chara-den display/Chara-den listl()

Enter the destination phone number and press l( ) to make a videophone call. pWhen the other party’s phone number is stored in the Phonebook, you can

retrieve it selecting from the Search Phonebook display by pressing Bo.

pYou can search for the phone number also from Received Calls by pressing Co

or from Redial by pressing Vo.

Information

pThe priority order of substitute images to be sent to the other party is as follows:

“Setting by call” → “Setting for Phonebook entry” →“Group setting” → “Select image”.

Voice/Videophone Calls

Substitute Image

You can set a Chara-den image for “Substitute image” of “Select image”.

Chara-den display/Chara-den list/Chara-den Recording

displayi()Substitute image

pFrom the Chara-den list, you can set it also by pressing m().

Chara-den Setup

You can perform settings for a Chara-den call. These settings are effective only for during a videophone call.

During a Chara-den calli()

Chara-den setupDo the following operations.

Item Operation/Explanation

Switch Chara-den Select a Chara-den image.

Voice/Videophone Calls

Action list You can display the list for actions that you can operate.

Change action You can switch the action mode between Whole Action Mode

At videophone

start-up

Whole Action

Mode

SW substitute img. You can switch a substitute image to be sent to the other party to

SW org. subst. img. You can switch a substitute image to be sent to the other party to

pIf you switch Chara-den images, the action mode switches to

Whole Action Mode.

pHighlight an action and press Oo( ) to execute the action.

Press l( ) to check the details of the action.

pYou can display the Action list also by pressing a.

( ) and Parts Action Mode ( ). pYou can switch modes also by pressing l.

the still image set for “Pre-installed” of “Select image”.

the still image set for “Original” of “Select image”.

Useful Functions for Videophone Calls

Switch Images to be Sent

You can switch images to be sent to the other party from the substitute image to the image through your camera. See page 307 for Chara-den.

During a videophone callm()

The image through your camera is sent to the other party. “ ” is displayed while it is being sent. pPress m( ) again to switch from the image through your camera to the

substitute image.

Information

pThe priority order of substitute images to be sent to the other party is as follows:

“Setting by call” → “Setting for Phonebook entry” → “Group setting” → “Select image”. Note that “Setting for Phonebook entry” and “Group setting” are disabled when a videophone call comes in without notifying the caller ID.

pEven when you make a videophone call sending a substitute image, you are charged

for the digital communication.

Switch Image Display Positions

You can switch the display locations of the received image and the sent image.

During a videophone call, press c().

pEach time you press

c( ), the displays

switch.

+cc

Zoom

At videophone start-up Wide

You can adjust the magnification for the camera image to be sent to the other party. During a videophone call, the maximum magnification of the camera is about 6.8 times.

During a videophone call

Use No to adjust the magnification.

pThe former zoom setting returns when the videophone call ends.

Function Menu during Videophone Call

Function menu Operation/Explanation

CHG to voice call See page 51.

Send DTMF tone/ DTMF tone OFF

V.phone settings (Visual preference)

V.phone settings (Brightness)

At videophone

start-up

During a Chara-den call, you can switch to the DTMF Transmission Mode that enables you to enter the data from the numeric keys and to send DTMF (touch-tone signals). You can operate it only during a Chara-den call. p“Send DTMF tone” is displayed when the mode is not DTMF

Transmission Mode and “DTMF tone OFF” is displayed in DTMF Transmission Mode.

pIn DTMF Transmission Mode, you cannot operate the action of

Chara-den images.

pThe DTMF tone may not be received depending on the device

of a receiving end.

See page 74.

You can adjust the brightness of the camera image to be sent to other party to -3 (dark) through +3 (bright).

BrightnessSelect a brightness level.

Voice/Videophone Calls

Function menu Operation/Explanation

V.phone settings (White balance)

At videophone

start-up

Automatic

V.phone settings (Color mode set)

At videophone

start-up Normal

V.phone settings (Night mode)

At videophone

Voice/Videophone Calls

start-up

OFF

V.phone settings (Focus)

At videophone

start-up

Landscape

Chara-den setup See page 72.

Backlight You can select whether to light the display constantly or light for

LCD AI See page 102.

Own number You can display your phone number.

Key guide You can display the guide of key operation during a videophone

You can adjust the colors of the camera image to be sent to the other party, to make the colors look more natural.

White balanceSelect an item.

Fine weather . . . . . For talking outdoors in fine weather

Cloudy weather. . . For talking in cloudy weather or in the shade

Automatic . . . . . . . For adjusting white balance automatically

Light bulb. . . . . . . . For talking under incandescent light

You can switch the color tone of the camera image to be sent to the other party.

Color mode setSelect a color tone.

You can lengthen the camera’s exposure time to make the camera image to be sent clear in a dark place.

Night modeON or OFF

You can set the focus for during a videophone call.

FocusClose-up or Landscape

about 15 seconds after an operation.

Constant light or 15 seconds light

call.

<Hands-free with Videophone>

Setting Videophone Hands-free

You can set whether to switch to Hands-free automatically for when a videophone call starts.

mSettingsVideophoneHands-free w/ V. phone

ON or OFF

pSee page 61 for the operation while Hands-free is activated and how to switch to

Hands-free.

Setting Image Quality for Videophone Calls

You can set the quality of the received image on the display.

mSettingsVideophoneVisual preference

Select an image quality.

p“Prefer motion spd” is effective for moving images. When there is little motion, the

quality becomes better if you set to “Prefer img qual”.

pIf you operate from the Function menu during a videophone call, the setting is

effective only for the current videophone call.

Information

pIf the radio wave conditions weaken during a videophone call, the image may appear

like a mosaic.

Changing Image Displays for Videophone Calls

You can set an image to be sent to the other party.

mSettingsVideophoneSelect image

Select an item.

On hold . . . . . Sets an image for during answer-hold (On hold).

Holding . . . . . Sets an image for while a call is on hold (Holding).

Substitute image

. . . . . . . . . . . . Sets a substitute image (still image or Chara-den) for when the

Record message

. . . . . . . . . . . . Sets an image while recording a record message.

Preparing . . . Sets an image for while playing back an answer message. Movie memo

. . . . . . . . . . . . Sets an image for while recording a movie memo.

Select an image.

Pre-installed . . . For sending a pre-installed still image to the other party.

Original . . . . . . . For sending an appropriate message with a still image stored

Chara-den. . . . . For sending a Chara-den image selected by “Substitute image”

pPress l( ) to play back a demo to check the still image or Chara-den

image.

pTo change the setting of “Original” or “Chara-den”, press i( ), select

“Change setting”, then select a still image or Chara-den image. If you have

selected “Original”, select a still image after selecting a folder. See “Set display”

for settable still images.

Information

pEven if you delete the still image selected from “Original”, that still image is displayed

to the other party. To change, set by “Change setting” or “Set display”.

camera is off.

using “Set display”.

from the Function menu while a Chara-den image is displayed. (See page 72) (Displayed only when “Substitute image” has been selected in step 1.)

Set by Call

You can set an image to be sent to the other party for making a videophone call.

Enter a phone number

bring up the detailed display of a Phonebook entry, redial item, dialed call record, or received call record.

i()Select imageChara-den

pTo cancel the setting by call, select “Release”. The setting is completed.

Select a Chara-den image.

Redialing as a Voice Call when a Videophone Call cannot be Connected

If a videophone call cannot be connected, it will be automatically redialed as a voice call.

mSettingsVideophoneVoice call auto redial

ON or OFF

Information

pThe charges for calls once switched to voice calls are billed at the rates for the voice

calls.

pVoice Call Auto Redial does not work when a videophone call cannot be connected

such as when the line is busy or the other party’s phone is in Public Mode (Drive Mode). However, Voice Call Auto Redial works when you make a videophone call to a phone that does not support the videophone function.

Voice/Videophone Calls

Setting for Switching between a Voice Call and a Videophone Call

You can let the other party know that your FOMA phone can switch between a voice call and a videophone call. This function is set to “Indication ON” at the time of contract. When “Notify switchable mode” is set to “Indication ON”, the caller can switch between the videophone call and voice call.

pYou cannot operate “Notify switchable mode” when you are out of the service area or

radio waves do not reach, or during a call.

mSettingsVideophoneNotify switchable mode

Do the following operations.

Item Operation/Explanation

Indication ON YESOK

Voice/Videophone Calls

Indication OFF YESOK

Check indication You can check the setting of the function.

Selecting Response to Incoming Videophone Calls during i-mode

mSettingsIncoming callV-phone while packet

Select an item.

V-phone priority

. . . .Shows the Videophone Call Receiving display. When you answer the

videophone call, packet communication is disconnected.

Packet downld priority

. . . .Rejects the videophone call and continues the communication.

V-phone answerphone

. . . .Connects the incoming videophone call to the Voice Mail Service Center.

Call forwarding

. . . .Forwards the incoming videophone call to the forwarding destination.

Information

pIf you have not signed up for Voice Mail Service or Call Forwarding Service, “Packet

downld priority” works even if you set to “V-phone answerphone” or “Call forwarding”.

Connecting FOMA Phone to External Devices to Use Videophone Function

You can operate your FOMA phone from an external device such as your personal computer for making or receiving videophone calls by connecting them using the FOMA USB Cable with Charge Function 01/02 (option). To use this function, you need to install a videophone application program on a dedicated external device or personal computer, and further, you need to prepare equipment (commercial item) such as an earphone/microphone or USB compatible web camera.

pFor operating environments for a videophone application program and how to set or

operate it, refer to the instruction manual or other literature for an external device.

pYou can use “ドコモテレビ電話ソフト (DOCOMO Videophone Software)” for the

application program that supports this function. Download it from the DOCOMO Videophone Software website. (For details such as operating environment for the personal computers, refer to the support web page.)

http://videophonesoft.nttdocomo.co.jp/ (In Japanese only)

FOMA videophone communication speed 64 kbps

Base station

FOMA

network

Information

pYou cannot make a videophone call from the external device during a voice call. pWhen you have signed up for Call Waiting Service, an incoming videophone call from

an external device during a voice call is recorded as a missed call in Received Calls. The same applies for an incoming voice call, videophone call, and 64K data communication during a videophone call from an external device.

Phonebook

Phonebooks Available for FOMA Phone . . . . . . . . . . . . . . . . . . . 78

Storing Phonebook Entries . . . . . . . . . . . .<Add to Phonebook> 78

Storing Displayed Phone Number/Mail Address in Phonebook

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Setting Groups . . . . . . . . . . . . . . . . . . . . . . . . . .<Group Setting> 83

Dialing from Phonebooks . . . . . . . . . . . . <Search Phonebook> 83

Editing Phonebook Entries . . . . . . . . . . . . . . <Edit Phonebook> 85

Deleting Phonebook Entries . . . . . . . . . . . . . . . . .<Delete Data> 85

Checking Number of Phonebook Entries

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <No. of Phonebook> 86

Making Full Use of Phonebooks . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Making a Call with a Few Touches . . . . . . . . . . . <2-touch Dial> 88

Accessing Phonebook Entries by Voice . . . . . . . . <Voice Dial> 88

Saving (Restoring/Updating) Phonebook to Data Storage Center

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Data Security Service> 90

Phonebooks Available for FOMA Phone

You can use two types of Phonebook, namely the Phonebook in the FOMA phone itself, and the Phonebook on the UIM.

Number of entries 1,000 entries 50 entries

Name (Reading) Group 19 groups 10 groups Phone number 4 phone numbers 1 phone number Phone number icon Mail address 3 mail addresses 1 mail address Mail address icon

Phonebook

Address

Basic item

Birthday Memo Image 100 images — Memory No. From 000 to 999 — Ring tone Vibrator Illumination Picture Chara-den 100 Chara-den

Mail ring tone

Setting item

Contents of Phonebook

Mail vibrator Mail illumination Answer message Restrict dialing Call rejection Call acceptance Call forwarding

Restrictions

Voice mail Secret code Storage in Secret Mode or Secret Data Only

FOMA phone UIM

○○

○

○ ○ ○ ○

images

○ ○ ○ ○

○

○ ○

Name Ring tone Vibrator Illumination Picture Chara-den Mail ring tone Mail vibrator

Contents of Group

—

— — — —

Mail illumination Answer message

○: Can be stored. —: Cannot be stored. pYou can set your UIM into another FOMA phone and use the UIM Phonebook entries.

FOMA phone UIM

○○

○

—

Storing Phonebook Entries

You can store Phonebook entries in the FOMA phone (Phone) or on the UIM.

Xo(for at least one second)Phone or UIM

—

The Edit Name display appears. Go to step 2 and enter a name.

Do the following

operations.

pYou can press No to switch

between the “Basic item” tab and “Settings” tab for the FOMA phone’s Phonebook.

For the FOMA phone For the UIM

Item Operation/Explanation

Name You can enter the name of the person or company in kanji,

Reading You can enter the reading in half-pitch katakana, alphabetic

Group In the FOMA phone, 19 groups are available.

hiragana, katakana, alphabetic characters, or numerals.

Enter a name.

For the FOMA phone, you can enter up to 16 full-pitch/32 half-pit ch characters. You can enter pictographs and symbols as well.

For the UIM, you can enter up to 10 full-pitch characters/21 half-pitch alphanumeric characters. (Half-pitch katakana characters cannot be entered.) When the entry contains both full-pitch and half-pitch characters, you can store up to 10 characters from the beginning regardless of full-pitch or half-pitch characters.

characters, or numerals.

Enter a reading.

pFor the FOMA phone, you can enter up to 32 half-pitch

characters. You can enter half-pitch symbols as well.

For the UIM, you can enter up to 12 full-pitch characters/25 half-pitch alphanumeric characters. (Half-pitch katakana characters cannot be entered.) When the entry contains both full-pitch and half-pitch characters, you can store up to 12 characters from the beginning regardless of full-pitch or half-pitch characters.

pIf the displayed reading is acceptable, you do not need to edit it.

However, depending on the characters entered for names or entering method, they are not reflected in the reading.

If you enter “ゎ (reduced size)” or “ヮ(reduced size)” for a name, “ワ (half-pitch, regular size)” (for the FOMA phone) and “ (regular size)” (for the UIM) are displayed in the reading field.

On the UIM, 10 groups are available.

Select a group.

pWhen the storage is completed with no group selected, the

Phonebook entry is stored in “No setting”.

ワ

Item Operation/Explanation

Phone number You can store up to four phone numbers per Phonebook entry in

the FOMA phone. You can set an icon for each phone number to categorize mobile phone numbers, office phone numbers, and so on. You can store only one phone number per Phonebook entry on the UIM.

Enter a phone number.

pEnter from the city code for the phone numbers. pYou can enter up to 26 digits. However, you can enter up to 20

digits for blue UIMs.

pPress and hold a for at least one second to insert a pause

(p) into the phone number you store. However, you cannot insert the pause (p) to the beginning of phone number or insert it consecutively. The pause (p) inserted to the end of phone number is not stored.

pIf you insert “:” in the middle of a phone number, you cannot

make a call. However, the phone number is recorded in Redial or Dialed Calls.

pYou can store the phone number which includes “#” such as

that for information service as well.

Select an icon.

pIf you have stored a phone number in the FOMA phone,

another “ <Phone number>” will appear in the Add-to-Phonebook display. To store another phone number, select “ <Phone number>”.

Phonebook

Item Operation/Explanation

Mail address You can store up to three mail addresses per Phonebook entry in

Phonebook

Address Enter a ZIP codeEnter a postal address.

Birthday Enter a birthdayON or OFF

Memo Enter a memo.

the FOMA phone. You can set an icon for each mail address to categorize mobile phone addresses, home addresses, and so on. You can store only one mail address per Phonebook entry on the UIM.

Enter a mail address.

pThe mail address can consist of up to 50 half-pitch alphabets,

numerals or symbol characters.

pWhen the mail address is “phone number@docomo.ne.jp”,

store the phone number only.

pFor the FOMA phone, you can set a secret code as well. (See

page 87)

Select an icon.

pIf you have stored a mail address in the FOMA phone, another

“ <Mail address>” will appear in the Add-to-Phonebook display. To store another mail address, select “ <Mail address>”.

pYou can enter up to 7 digits for the zip code. pYou can enter up to 50 full-pitch/100 half-pitch characters for the

postal address. Further, you can enter pictographs as well.

pYou cannot enter “〒” or “-” (hyphen) in the zip code.

pYou can enter the birthday from January 1, 1800 through

December 31, 2099.

pWhen you set to “ON”, the birthday is stored as an anniversary

in the schedule of every year. “誕生日 (Birthday) (name)” is stored as the anniversary content.

pEven if you delete the Phonebook entry, the anniversary stored

in Schedule is not deleted.

pYou can enter up to 100 full-pitch/200 half-pitch characters.

Further, you can enter pictographs as well.

Item Operation/Explanation

Image The stored still image is displayed when you call up the

Memory No. Enter a memory number.

Ring tone You can set a ring tone for when a voice call or videophone call

Phonebook entry.

Select an item.

Select image . . . You can store a still image in Data Box. Shoot image . . . You can store the shot still image. Perform

pTo release the stored still image, select “Release image”. pThe size of a still image you can store is Stand-by (240 x 427) or

smaller and up to 300 Kbytes in JPEG format or GIF format.

pIf you store a still image larger than 72 x 54 dots, it is displayed

shrunk on the detailed Phonebook display.

pIf you store a still image larger than 240 x 180 dots, it is

displayed shrunk on the Call Receiving display.

pWhen “Disp. PH-book image” is set to “ON”, the stored still

image is displayed for an incoming call. However, when another image is stored in the “Picture” field, that image is preferentially displayed for the incoming call.

pEnter a three-digit number of “000” through “999”. pThe lowest empty memory number “010” through “999” is

entered in advance. If “010” through “999” are all occupied, the lowest empty memory number from “000” through “009” is entered.

comes in from the person stored in the Phonebook.

SEL ring tone

Go to step 2 on page 92. pTo release the stored ring tone, select “RLS ring tone”.

step 2 through step 3 on page 137.

Item Operation/Explanation

Vibrator You can set a vibration pattern for when a voice call or

Illumination You can set an illumination pattern for when a voice call or

Picture You can set an image to be displayed for when a call comes in

Chara-den The stored Chara-den image is displayed as a substitute image

Mail ring tone You can set a ring tone for when a mail message comes in from

Mail vib. You can set a vibration pattern for when a mail message comes

videophone call comes in from the person stored in the Phonebook.

SEL vibratorSelect a vibration pattern.

pTo release the stored vibrator, select “RLS vibrator”.

videophone call comes in from the person stored in the Phonebook.

SEL illum.Select a color pattern.

pTo release the stored illumination, select “RLS illum.”.

from the person stored in the Phonebook.

SEL pictureSelect a type of imageSelect a folder Select an image.

pTo release the stored image, select “RLS picture”.

for videophone calls with the person stored in the Phonebook.

SEL Chara-denSelect a Chara-den image.

pTo release the stored Chara-den image, select “RLS

Chara-den”.

the person stored in the Phonebook.

SEL ring tone

Go to step 2 on page 92. pTo release the stored mail ring tone, select “RLS ring tone”.

in from the person stored in the Phonebook.

SEL vibratorSelect a vibration pattern.

pTo release the stored mail vibrator, select “RLS vibrator”.

Item Operation/Explanation

Mail illum. You can set an illumination pattern for when a mail message

Answer msg. You can set an answer message for Record Message by

comes in from the person stored in the Phonebook.

SEL illum.Select a color pattern.

pTo release the stored mail illumination, select “RLS illum.”.

Phonebook entry.

SEL answer msgSelect an answer message.

pTo release the stored answer message, select “RLS answer

msg”.

Press l().

pIf you have not entered any name, “ ” is not displayed and you cannot store

the entry.

Phonebook entries while editing

When the low battery alarm sounds

The Phonebook entry you are editing is saved automatically. The confirmation display appears asking whether to resume editing when you continue editing after charging the battery or when you operate step 1 on page 78 and select the storage location for the interrupted Phonebook entry after changing to a charged battery.

Recall. . . . You can resume editing the Phonebook entry.

New . . . . . You can edit a new Phonebook entry. In this case, the interrupted data is

retained. If you execute “Add to phonebook” after storing the new Phonebook entry, the confirmation display appears again.

pOnly the most recently interrupted entry is retained. pIf you resume editing the data but then cancel editing without storing it, that data will be

abandoned. Once you recall the data, be sure to store it.

If you receive a call or mail

You can respond it leaving the edited data as it is, thanks to the Multitask function. To return to the Phonebook Edit display, press and hold x for at least one second to switch the menu. You can return to the Phonebook Edit display also by ending the call or mail function.

Phonebook

Storing Displayed Phone Number/Mail Address in Phonebook

You can store the displayed or selected phone number, mail address, and still image in the FOMA phone’s or UIM’s Phonebook.

While a phone number is entered Phone number While a redial item, dialed call record, or received call record is displayed While Sent Address or Received Address is displayed Phone number/Mail address While a site or screen memo is displayed Phone number/Mail address While the text of Message R/F or mail is displayed Phone number/Mail address

Phonebook

While the data scanned by Bar Code Reader or Text Reader is displayed While a ToruCa file is displayed Phone number/Mail address While the Still Image list or a still image is displayed Still image

Bring up/Select an item to be storedi()

Add to phonebook

pTo store the address of the sender (or of another recipient of simultaneous mail)

of the received mail or the destination address of the sent mail into the Phonebook, select “Store address”. When the addresses of the sender and anothe r recipient of simultaneous mail are found or the multiple destination addresses are found, the display for selecting an address appears. Use Bo to select the mail address or phone number you want to store.

pTo store the results scanned by Text Reader in a Phonebook entry, select “Store

phone No.” or “Store mail add.”.

pTo store a still image in the Phonebook, select “Phonebook” from “Set display”. pWhen “Add to phonebook” is displayed on the Scanned Code Result display for

Bar Code Reader, select “Add to phonebook”; then other information in the scanned code besides the phone number or mail address is entered into each field.

Operation Storable items

Phone number

Phone number/Mail address

Phone or UIMSelect a storing method.

New . . . Go to step 2 on page 78. Add . . . Adds data to the existing Phonebook entry. When storing data on the

UIM, “Overwrite” is displayed.

Select a search methodSearch the Phonebook

Select a Phonebook entry to be storedOo()

The phone number or mail address is entered automatically.

pSee step 2 on page 78 to edit other items in the Phonebook entry. pWhen you store into the FOMA phone’s Phonebook, you can remain the original

entry and store a new entry into a different location by changing the memory number.

l()YES

pIf you store the entry in the UIM Phonebook, select “Overwrite” to overwrite the

original entry, or select “Add” to store it as a new entry.

Information

pThe Phonebook entry does not store the information of “Notify caller ID” included in

Redial/Dialed Calls. To set Caller ID Notification, add “186”/“184” to the phone number and store it.

pCharacters that cannot be stored may be replaced by spaces or deleted, and then

stored.

pYou may not be able to store the information from some sites into the Phonebook.

Setting Groups

You can utilize the Phonebook by sorting the entries by group such as “Company” or “Friend”, or by your interest such as “Baseball” or “Ceramic art”. You can set a ring tone, vibration pattern, or illumination by group.

mPhonebookGroup setting

pThe groups on the UIM are indicated by “ ”.

pTo reset the group names and respective settings by group, which have already

been stored, press i( ), select “Reset group”, and then select “YES”.

Highlight a group and press l()

Select an item to be setSet the contents.

pWhen you select “ Group name”, enter a group name. You can store up to 10

full-pitch/21 half-pitch characters. However, you can store only up to 10 characters (regardless of full-pitch or half-pitch characters) when you enter both full-pitch and half-pitch characters for a UIM group name.

pSee step 2 on page 78 for the operations of the other items. However, you cannot

set for groups on the UIM.

pSelect a stored group, or press i( ) and select “Check setting” to check

its settings. However, you cannot check the settings of the groups on the UIM.

Press l().

Dialing from Phonebooks

You can retrieve stored Phonebook entries by eight search methods.

XoDo the following operations.

pThe display for the same search method as the

previous one appears once you have carried out a search. Press r to show the Search Phonebook display.

Search Phonebook

display

Item Operation/Explanation

All? You can bring up all Phonebook entries.

Reading? You can enter the reading of the other party’s name from the first

Group? You can bring up Phonebook entries stored in the specified

Memory No.?

[FOMA phone only]

The tabs appear on the top of the Phonebook list. (See page 84)

character and search. You do not need to enter the full reading.

Enter a part of the readingBo

The tabs appear on the top of the Phonebook list. (See page 84)

group.

Select a group.

The tabs appear on the top of the Phonebook list. (See page 84)

pIf you press i( ) on the Group list, the Function menu

for “Group setting” is displayed.

You can search for the entry by the memory number assigned when it was stored in the Phonebook.

Enter the memory number.

pEnter from “000” through “999” in three digits. p

The tabs appear on the top of the Phonebook list. (See page 84)

pFrom the Stand-by display, you can press d and then press

Bo to display the Memory No. Dial display. From there you can

make a voice call by entering the memory number of the phone number.

Phonebook

Item Operation/Explanation

Name? You can enter the other party’s name from the first character and

Phone number? You can enter a part of the other party’s phone number and

Mail address?

Phonebook

2-touch dial?

[FOMA phone only]

search. You do not need to enter the full name.

Enter a part of the nameBo

search. You can search for the entry even from the middle of phone number.

Enter a part of the phone numberBo

pYou can display the Phonebook list also by entering a part of

the phone number from the Stand-by display or the “Talking” display, and pressing Bo.

You can enter a part of the other party’s mail address and search. You can search for the entry even from the middle of mail address.

Enter a part of the mail addressBo

You can bring up the list of Phonebook entries in memory number 000 through 009. pPhonebook entries not yet stored or being set with secret are

displayed as ＜−−−＞.

Select an entryd or Oo()

pWhen the entry contains multiple phone numbers, or when you searched by “Mail

address?”, press Mo from the detailed display to select a phone number.

pYou can make a videophone call by pressing l().

Information

pIn a search method other than “Group?” and “2-touch dial?”, enter nothing and press

+Bo; then you can search all through the Phonebook.

When no Phonebook entry is found that matches the condition you entered by “Reading?” or “Memory No.?”, the entry that is the closest to the condition is displayed.

Search order

The Phonebook entries are searched in the order of readings you entered for storing, as follows: “Space at the beginning of the reading” → “Japanese syllabary (

→

“Alphabet (A, a, B, b, ...Z, z)” → “Numerals (0 through 9)” → “Symbols” → “No reading”. For “All?” and “Reading?”, searching is done in the following order: “Japanese syllabary ( at the beginning of the reading” → “Numerals (0 through 9)” → “Symbols” → “No reading”.

※The Memory No. Search searches in the order of the memory numbers.

ア、イ、ウ、エ、オ、...ン)”→

“Alphabet (A, a, B, b, ...Z, z)” → “Space

ア、イ、ウ、エ、オ、...ン

About Phonebook List

When you search from “All?”, “Reading?”, “Group?”, or “Memory No.?”, the tabs appear on the top of the Phonebook list. With “All?” and “Reading?”, the entries are sorted by every column of reading, with “Memory No.?” by every 100 of the memory number, and with “Group?” by every group. Press No to display the Phonebook entries in the tab at left or right. However, when there are seven or more Phonebook entries in a tab, pressing m(), c(), or <> brings up the previous or next page. pAfter you search by “Reading?”, you can move the cursor to the “ア” through “ワ”, “英”,

and “他” tab by pressing each numeric key from the list. When you successively press the same numeric key, you can move the cursor within the same column. <Example>Press 5 to display the “ナ” tab. Each time you press 5, the cursor

pAfter you search by “Group?”, you can move the cursor to the top of each column in the

tab by pressing each numeric key from the list. When you successively press the same numeric key, you can move the cursor within the same column. <Example>Press 5 to move the cursor to the top of the “ナ” column. Each time you

pAfter you search by “Memory No.?”, you can move the cursor to the “000~” to “900~”

tab by pressing each numeric key from the list. <Example>Press 5 to move the cursor to the “500~” tab.

moves to the top of “ニ” “ヌ” and so on.

press 5, the cursor moves to the top of “ニ” “ヌ” and so on.

Phonebook list

)”

You can make a voice call to the phone number stored for the name highlighted on the Phonebook list, by pressing d. Also, press l( ) to make a videophone call. When multiple phone numbers are stored for the name, the one stored first will be dialed.

p“ ” appears for the Phonebook entries set to A by Phonebook 2in1 Setting, “ ”

appears for the Phonebook entries set to B, and “ ” appears for the Phonebook entries set to common data. (Only in Dual Mode)

About the detailed display

Use No to highlight a tab, then the detailed contents are displayed. pFor the Phonebook entry stored

on the UIM, “ ” is displayed on the memory number field.

pWhen Notify Caller ID is set to

“Notify caller”, “ ” appears, and when set to “Don’t notify”, “ ” appears.

pUnder the still image, “ ”

appears for the Phonebook entries set to A by Phonebook 2in1 Setting, “ ” appears for the Phonebook entries set to B, and “ ” appears for the Phonebook entries set to common data. (Only in Dual Mode)

pWhen a Phonebook entry contains the setting for Multi Number or Chaku-moji, the set

contents are displayed in the Item list/Phone Number display.

Item list

The first stored phone number, mail address, postal address, birthday, and memo are displayed.

Phone number

Mail address

pWhen you select the item, you can compose an i-mode mail message with that mail

address entered into the address field.

Personal information

pWhen you select a postal address, memo, or still image, the full display appears. Press

Oo() or r to return to the former display.

Settings

pWhen you select each item, a demo is played back.

Press Oo() or r to end the demo.

Group Name

Detailed Phonebook

display (Item list)

Memory No.

Still image

Notify caller ID

Editing Phonebook Entries

Detailed Phonebook displaym()

Select an item to be editedEdit the contents.

pSee step 2 on page 78 for how to edit the Phonebook entry. pEven if you edit the Phonebook entry in the FOMA phone (Phone), you can

remain the original contents in the original location and store the edited contents in the different location by changing the memory number.

l()YES

pIf you edited the UIM Phonebook entry, select “Overwrite” to overwrite the original

contents, or “Add” to save the contents as a new entry.

Deleting Phonebook Entries

Delete from the Detailed Phonebook Display

Detailed Phonebook displayi()Delete data

Select an itemYES

pYou can delete an item highlighted by pressing Mo from the detailed display or

delete the Phonebook entry.

Delete from the Phonebook List

Phonebook listi()Delete data

Do the following operations.

Item Operation/Explanation

Delete this YES

Phonebook

Item Operation/Explanation

Delete selected Put a check mark for Phonebook entries to be deleted

Delete all in tab You can delete all the Phonebook entries for the displayed tab.

Delete all You can delete all Phonebook entries including secret entries.

Phonebook

l()YES

pYou can check or uncheck entries all at once by pressing

i( ) and selecting “Select all in tab/Select all/Release all in tab/Release all”.

pPerform the same operation as that of “Delete all” when you

have selected all Phonebook entries including secret ones.

YES

Enter your Terminal Security CodeYESYES

<No. of Phonebook>

Checking Number of Phonebook Entries

mPhonebookNo. of phonebook

Phone Phonebook . . . The number of Phonebook entries stored in the FOMA phone

Secret . . . . . . . The number of Phonebook entries stored as secret data

Image . . . . . . .The number of Phonebook entries in which still images are stored

Chara-den . . . .The number of Phonebook entries in which Chara-den images are

Voice dial. . . . .The number of Phonebook entries set as voice dial entries

Rest . . . . . . . . . : The number of phone numbers that can still be stored

UIM Phonebook . . . The number of Phonebook entries stored on the UIM

Information

pWhile you are using 2in1, the number of displayable Phonebook entries for each

mode is displayed. (See page 403)

(Phone)

(Displayed in Secret Mode or Secret Data Only)

stored

: The number of mail addresses that can still be stored

Making Full Use of Phonebooks

Function Menu of the Phonebook List

Function menu Operation/Explanation

New You can store a new Phonebook entry.

Sort You can change the display order.

Attach to mail You can send an i-mode mail message with the Phonebook entry

Send Ir data (Send phonebook)

Send Ir data (

Send all phonebook

transmission

(Send phonebook)

transmission

(

Send all phonebook

Copy to microSD See page 316.

Connect to Center See page 90.

Delete data See page 85.

Character size You can switch character sizes for the Phonebook.

Set secret/Release secret

Go to step 1 on page 78.

Select a type of order.

pYou can sort Phonebook entries in reverse order by selecting

“Ascending” or “Descending”.

pYou cannot sort on the Phonebook list with tabs displayed.

attached. Go to step 2 on page 180.

See page 329.

)

See page 331.

)

(See “Phonebook” on page 112)

You can activate/deactivate Secret for the Phonebook entry. pIf you select “Set secret” in ordinary mode (not in “Secret mode”

or “Secret data only”), enter your Terminal Security Code.

Function Menu of the Detailed Phonebook Display

Function menu Operation/Explanation

Notify caller ID See page 56.

Prefix numbers See page 60.

Int’l dial assist See page 59.

2in1 dial You can select a phone number to notify the other party in Dual

Multi number You can select a phone number to be notified to the other party.

Chaku-moji See page 54.

Restrictions See page 123.

Edit data Go to step 1 of “Editing Phonebook Entries” on page 85.

Delete data See page 85.

Add desktop icon See page 109.

Compose message You can compose an i-mode mail message to send to the mail

Compose SMS You can compose an SMS message to send to the phone

Attach to mail You can send an i-mode mail message with the Phonebook entry

Send Ir data (Send phonebook)

Send Ir data (Send all phonebook)

transmission

(Send phonebook)

transmission

(Send all phonebook)

Mode of 2in1. (See page 402)

(See page 400)

address. Go to step 3 on page 180.

number set as the destination address. Go to step 3 on page 225.

attached. Go to step 2 on page 180.

See page 329.

See page 331.

Function menu Operation/Explanation

Copy to microSD See page 316.

Connect to Center See page 90.

Copy name pYou can paste the copied text to a mail message and others.

Copy phone number/ Copy mail add./ Copy address/ Copy birthday/ Copy memo

Secret code You need to add the recipient’s secret code when sending i-mode

Character size You can switch the character size for the Phonebook and on the

Set secret/Release secret

Copy to UIM/ Copy from UIM

pFrom the detailed display, press Mo to highlight an item to be

copied. The items in the Function menu differ depending on the highlighted item.

pYou can paste the copied text to a mail message and others.

mail to anyone who has registered a secret code. Once you set the secret code for the mail address in the Phonebook entry, it will be added automatically whenever you send mail to that address.

Enter your Terminal Security CodeSet code

pFrom the detailed display, press Mo to highlight a phone

number or mail address to be set with a secret code.

pTo check the secret code, select “Check code”. pTo release the secret code, select “Release code”.

Enter a four-digit secret codeYES

pIn the Function menu, “Secret code” is indicated by “★”, after it

is set.

pEnter a four-digit number for secret code. You cannot set

“0000”.

displays within “Phonebook settings”, etc. (See “Phonebook” on page 112)

See page 86.

See page 374.

Phonebook

Function menu Operation/Explanation

Select image See page 75.

Sort phone number/ Sort mail address

Information

Phonebook

pYou cannot set secret codes for UIM Phonebook entries. pThe secret code can be added only when the recipient’s mail address is in the form of

“phone number” or “phone number@docomo.ne.jp”. It cannot be added to any other form of mail address.

pIf you have stored the mail address as “phone number＋secret code@docomo.ne.jp”,

you cannot reply to mail messages from the party of that mail address. After changing the mail address to “phone number@docomo.ne.jp”, set the secret code.

<2-touch Dial>

Select a phone number or mail address Use Bo to change the orderOo()

p From the detailed display, press No to highlight an item to

be sorted. The items in the Function menu differ depending on the highlighted item.

pTo change the order in succession, repeat the above steps.

l()

Making a Call with a Few Touches

When the entry is stored in memory number “000” through “009” in the FOMA phone’s Phonebook, you can dial the phone number just by pressing the lowest one digit of memory number and d.

Numeric key (0 to 9)d or Oo()

pYou can make a videophone call by pressing l().

Information

pWhen the Phonebook entry contains multiple phone numbers, the first phone number

will be dialed.

Information

pWhen you set “Restrict dialing” to a Phonebook entry of memory number 000 through

009, set it to the first phone number in the Phonebook entry.

pWhen you store a Phonebook entry of memory number from 000 through 009 as

secret data, make a call to that entry in Secret Mode or Secret Data Only.

Accessing Phonebook Entries by Voice

Just vocalize the other party’s voice dial name and then the Phonebook entry is accessed for making a call.

Voice Dial Setting

You can store up to 100 voice dial entries selecting from among the Phonebook entries stored in the FOMA phone (Phone).

mPhonebookPhonebook settings

Voice dial setting<New>

pYou can edit the stored voice dial name by pressing l( ). Go to step 3. pTo delete the stored voice dial entry, press i( ) and select “Delete” or

“Delete all” and then select “YES”.

Search the PhonebookSelect a Phonebook entry.

The display for search method you used last time appears. pThe “★” mark is added to the Phonebook entry stored in the Voice Dial list.

Enter a voice dial name.

pYou can enter up to 22 half-pitch katakana characters. pThe reading (katakana only) of the Phonebook entry is displayed as the voice dial

name. Correct the name to the easy-to-identify words.

Information

pThe voice dial name set by this function is effective only for calling up a voice dial

entry. For the voice guidance function, the reading (name) stored in the Phonebook is

read aloud.

+m-2-6

Information

pWhen multiple similar voice dial names are stored or when the voice dial name is

short, the recognition rate lowers and a wrong voice dial entry (Phonebook entry) might be accessed. In this case, rename the existing voice dial name and store it.

pYou cannot store “ボイスセッテイ (Boisusettei)” as a voice dial name.

Dial from Phonebook by Voice

By your voice, you can access the Phonebook entry you set in the Voice Dial list. When “Read aloud settings” is set to “ON” and “Voice dial” is checked, the operation is guided by the voice guidance.

d(for at least one second)

As soon as the voice recognition start tone sounds,

vocalize the voice dial name.

Start vocalizing within four seconds after the voice recognition start tone sounds. Once the voice is recognized as a voice dial entry, the detected result is displayed. pYou cannot change the volume of the voice recognition start tone. The voice

recognition start tone does not sound during Manner Mode.

pIf you say the word “ボイス設定 (Boisusettei)”, the display of “Voice settings”

appears. (See page 89)

pWhen “Auto voice dial” is set to “ON”, the display for Auto Voice Dial appears

after the voice is recognized as a voice dial entry. Then about two seconds later, the FOMA phone automatically dials out.

Highlight a detected result and press

The first phone number in the selected Phonebook entry is dialed. pYou can bring up the detailed Phonebook display by pressing l().

Highlight a phone number and press d or Oo( ) to make a voice call. Also, you can make a videophone call by pressing l().

Information

pWhen you vocalize, keep your mouth away from the microphone about 10 cm. If your

voice is too distant, it may be difficult to recognize your voice.

pPronounce the voice dial name as clearly as possible. pBefore and after voice production, avoid making the sounds unrelated to the voice dial

name such as clearing your throat, clicking your tongue, noisy breathing or other noise.

pVocalize in quiet, noise-free locations.

d

or Oo().

Information

pWhile vocalizing, do not put your fingers over the microphone, or press or brush the

keys.

To access a voice dial entry using an earphone/microphone

You need to set “Voice earphone dial” to “ON” and open the FOMA phone in advance.

Press and hold the switch of the earphone/microphone

(option) for at least one second.

Perform the operations of “Dial from Phonebook by

Voice” on page 89.

pYou can make a call also by pressing the switch of the earphone/microphone

instead of pressing d or Oo.

Voice Settings

mSettingsOther settingsVoice settings

Do the following operations.

Item Operation/Explanation

Auto voice dial You can automatically make a call to the phone number

Voice earphone dial You can access the voice dial entries by using an earphone/

Read aloud settings See page 358.

Read aloud volume See page 359.

Read aloud speed See page 359.

Read aloud output See page 359.

accessed by voice.

ON or OFF

microphone (option).

ON or OFF

Phonebook

Item Operation/Explanation

Read aloud valid set.

See page 359.

Saving (Restoring/Updating) Phonebook to Data Storage Center

You can save the Phonebook stored in your FOMA phone to the Data Storage Center. You can use the “電話帳お預かり (Data Security Service)” site of i-mode (iMenu→English→My Menu→電話帳お預かり) for restoration of the saved Phonebook and automatic update setting.

Phonebook

Data Security Service is a pay service that is available on a subscription basis.

pYou cannot use Data Security Service when you are out of the i-mode service area or

when the power is off.

pFor details on Data Security Service, refer to “Mobile Phone User’s Guide [i-mode]

FOMA version”.

mLifeKitData Security Service

Do the following operations.

Item Operation/Explanation

Connect to Center Enter your Terminal Security CodeYES

Sent/recv. PB data list

PB image sending You can set whether to save images set for the Phonebook

You can display the records of communication such as saving the Phonebook, mail messages, or images to the Data Storage Center.

Select a record.

pSelect a communication completion time in the list to switch to

the detailed display.

entries to the Data Storage Center.

ON or OFF

Downloading the Phonebook from the Data Storage Center to your FOMA phone

Note that if you delete Phonebook entries from your FOMA phone and save the Phonebook to the Data Storage Center, the Phonebook entries on the Data Storage Center are also deleted. When you download the Phonebook from the Data Storage Center to your FOMA phone, do the following operations to restore it.

ii

MenuEnglishMy Menu

お預かりセンター

2. Select “ケータイへダウンロード (Download to mobile phone)” from the Phonebook

on the Data Storage CenterOK pAbout 15 seconds later, download starts. Wait for a while with the Stand-by display

shown.

(Data Storage Center)Enter your i-mode password.

電話帳お預かり

(Data Security Service)

Information

pYou cannot save the UIM Phonebook. pWhen the Phonebook entries saved to the Data Storage Center exceeds the number

of Phonebook entries storable in the FOMA phone’s Phonebook, the excess entries

cannot be updated.

pUp to 30 records are saved. When more than 30 records are saved, the older records

are overwritten.

pYou cannot save the images whose output from FOMA phone is prohibited.

Auto-update

On the site of the Data Storage Center, you can set so as to periodically update and save the Phonebook entries in your FOMA phone to the Data Storage Center.

pFor details, refer to “Mobile Phone User’s Guide [i-mode] FOMA version”.

Information

pThe Phonebook is not automatically updated while another function is working at the

time of Auto-update.

pIf the Phonebook cannot be updated, the notification icon of “ ” (PB in Center

updated) appears on the Stand-by display. Select “ ”, and the update display

appears if Auto-update is set. If Auto-update is not set, the update display appears

after you enter your Terminal Security Code.

Sound/Screen/Light Settings

Sound Settings

Changing Ring Tone. . . . . . . . . . . . . . . . . . <Select Ring Tone> 92

Setting Play Start Position of Melody Set for Ring Tone or Alarm

Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Position to Play> 93

Informing You of an Incoming Call by Vibration . . .<Vibrator> 93 Using Recorded Sound as Ring Tone . . . <Voice Announce> 94

Changing Calling Tone. . . . . . . . . . . . . . <Melody Call Setting> 94

Setting Keypad Sound . . . . . . . . . . . . . . . . . . <Keypad Sound> 94

Setting Charging-start/end Tones . . . . . . . . . <Charge Sound> 95

Sounding Alarm when a Line is Likely to be Disconnected

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Quality Alarm> 95

Setting Ring Time for Mail and Messages R/F

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Mail/Message Ring Time> 95

Sounding Ring Tone from Earphone Only

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Headset Usage Setting> 95

Silencing Tones from FOMA Phone . . . . . . . . <Manner Mode> 96

Selecting Manner Mode Type . . . . . . . . . .<Manner Mode Set> 97

Screen/Light Settings

Changing Displays . . . . . . . . . . . . . . . . . . . . . .<Display Setting> 98

Displaying an Image Stored in Phonebook during Ringing

. . . . . . . . . . . . . . . . . . . . . . . . . . . . <Display Phonebook Image> 100

Setting Displays for Private Window . . . . . . <Private Window> 101

Displaying Arrival Information by Opening FOMA Phone

. . . . . . . . . . . . . . . . . . . . . . . . . . . .<Received Mail/Call at Open> 101

Setting Lights for Display and Keypad . . . . . . . . . . <Backlight> 101

Adjusting Quality of Display Automatically . . . . . . . . .<LCD AI> 102

Making Display Hard to See from People Around

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <View Blind> 103

Setting Quality of Display . . . . . . . . . . . . . . . . .<Image Quality> 103

Setting Color Combination for Display

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Color Theme Setting> 103

Setting Display of Main Menu . . . . . . . . . . <Menu Icon Setting> 103

Using Kisekae Tool. . . . . . . . . . . . . . . . . . . . . . . <Kisekae Tool> 104

Using Feel Setting Color of Call/Charging Indicator and Others

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <Illumination> 105

Checking Missed Calls and New Mail by Tone and Call/Charging

Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . .<Info Notice Setting> 107

Using Icons on Desktop . . . . . . . . . . . . . . . . . . . <Desktop Icon> 107

Changing Character Font. . . . . . . . . . . . . . . . . . . . . . . . . .<Font> 111

Changing Character Size . . . . . . . . . . . . . . . . . <Character Size> 111

Setting Clock Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

＊

Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . .<Feel＊Mail> 105

+m-1-3

Changing Ring Tone

You can set a ring tone for each incoming type. If you select an i-motion movie, the i-motion movie and sound are played back for incoming calls/messages. (Chaku-motion)

pThe ring tone is the PCM sound source, chord of 128 tones, and ADPCM compliant. pSee “Add to Phonebook” for setting a ring tone by Phonebook entry, and see “Group

Setting” for setting it by group.

■Ring Tone List (pre-installed)

Display Title Name of Lyricist/Composer Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 TRITSCH TRATSCH POLK

EL COLIBRI EL COLIBRI

LA FILLE AUX CHEVEUX JAZZ JAZZ

Sound/Screen/Light Settings

APPRENTI SORCIER APPRENTI SORCIER

SOMEDAY MY PRINCE WI

POLET SHMAJA POLET SHMAJA

SUMMERTIME SUMMERTIME

RHAPSODY ON A THEME

PEER GYNT SUITE NR 1

Computer

ーーーーーーーーーー

TRITSCH TRATSCH POLKA OP 214

LA FILLE AUX CHEVEUX DE LIN

SOMEDAY MY PRINCE WILL COME

RHAPSODY ON A THEME OF PAGANINI OP 43 PEER GYNT SUITE NR 1 OP 46/ MORGENSTEMNING

ーー

Composer: STRAUSS JUN JOHANN Composer: SAGRERAS JULIO S Composer: DEBUSSY CLAUDE ACHILLE

Composer: DUKAS PAUL ABRAHAM Composer: CHURCHILL FRANK E Composer: RIMSKIJ KORSAKOVICH NICOLAS ANDR Composer: GERSHWIN GEORGE

Composer: RACHMANINOFF SERGEI

Composer: GRIEG EDVARD HAGERUP

ー

Display Title Name of Lyricist/Composer Twinkle Garden Terrace Propeller Elegance Waterdrop Bubble Spy Magical Stick Scratch Smart Beep Ring Ring Ring Sound of Water

美ら海ｶｸﾚｸﾏﾉﾐ

※ i-motion movie

(Note) The names of lyricists and composers are described conforming to the JASRAC

※

web page. Whole part of long titles may not be displayed due to restriction of the display size.

ーーーーーーーーーーーーーーーーーーーーーーーー

美ら海ｶｸﾚｸﾏﾉﾐ

(CHURAUMI KAKUREKUMANOMI)

ー

mSettingsSoundSelect ring tone

Select an incoming type.

pSelect an item and pr ess l( ) to check the contents actually played back

or displayed.

Select ring toneSelect a type of ring tone.

Melody . . . . . . . . . . . Sets a melody as a ring tone.

MUSIC. . . . . . . . . . . . Sets a Chaku-uta Full®music file as a ring tone.

imotion . . . . . . . . . Sets an i-motion movie as a ring tone. (Chaku-motion/

Voice announce . . . Sets the sound recorded by “Voice announce” as a ring

OFF . . . . . . . . . . . . . . Sets a ring tone off. The setting is completed.

Chaku-uta

tone. The setting is completed.

)

Select a folderSelect a ring tone.

pIf you select “MUSIC” in step 2, select “Fullsong ring tone” or “Point ring tone”.

(See page 350)

pSee page 167 when you select “i-mode srch”.

Information

pYou can set the Call Receiving display by selecting “Phone” or “Videophone”, and

then by selecting “Select calling disp.”. Go to step 2 on page 100.

pYou can set the Mail Receiving display by selecting “Mail”, “Chat mail”, “MessageR” or

“MessageF”, and then by selecting “Select receiving disp.”. Go to step 2 of “Set Stand-by Display” on page 98.

pThe priority order of ring tones is as follows: “Read aloud settings” → “Setting for

Phonebook entry” → “Group setting” → “Select ring tone”. If a call comes into Number B while using 2in1, the priority order of the ring tones is as follows: “Read aloud settings” → “Setting for Phonebook entry” → “Group setting” → “Ringtone set. for No. B” (see page 401).

pThe ring tone or images set at purchase might be played back or displayed for

incoming calls or messages, depending on the combination of this function and “Display setting”.

pSee “imotion info” to check whether the i-motion movie can be set for a ring tone. pWhen you set an i-motion movie containing video and sound for a mail ring tone, you

can press -r or others to stop the ring tone.

pWhen you set an i-motion movie containing video and sound for a ring tone

(Chaku-motion), it is played back taking priority over “Display setting”. However, if you set a voice-only i-motion movie for the ring tone, the image set by “Display setting” is displayed.

pWhen you set an i-motion movie containing video and sound for “Select calling disp.”,

the i-motion movie is played back taking priority over this function for incoming calls. However, if you set an i-motion movie containing only video for “Select calling disp.”, the ring tone selected for this function is played back for incoming calls.

pWhen different types of mail — i-mode mail, SMS messages, chat mail, or Messages

R/F — are received at the same time, the priority order of ring tone as follows: “Chat mail” → “i-mode mail/SMS” → “MessageR” → “MessageF”. If you receive the same type of mail simultaneously, the ring tone corresponding to the mail you have received last works.

pFor the melody downloaded from a site or attached to mail, or the melody prohibited

to attach to mail or output from the FOMA phone, a playing part may be specified in advance. When the play-part-specified melody is set for the ring tone, only the specified part is played back.

+m-6-4

Setting Play Start Position of Melody Set for Ring Tone or Alarm Tone

mSettingsSoundPosition to play

Select a play start position.

Play all. . . . . . . . Plays back from the beginning of the melody.

Play portion . . . Plays back from the start position set for the melody.

+m-5-4

Informing You of an Incoming Call by Vibration

You can set the vibrator to notify you of incoming calls and mail.

mSettingsIncoming callVibrator

Select an incoming typeSelect a vibration pattern.

Pattern 1 . . . . . . . . Alternates between vibration on (about 0.5 second) and off

Pattern 2 . . . . . . . . Alternates between vibration on (about 1 second) and off

Pattern 3 . . . . . . . . Alternates between vibration on (about 3 seconds) and off

Melody linkage . . . Vibrates in time with the vibration pattern stored in the melody.

OFF . . . . . . . . . . . . Does not vibrate.

pWhile you are selecting a pattern, the FOMA phone vibrates by the selected

pattern for confirmation. However, it does not vibrate if you select “Melody linkage”.

pThe following icons are displayed on the Stand-by display while the vibrator is set:

: Vibrates for incoming voice calls or videophone calls.

: Vibrates for incoming mail, chat mail or Messages R/F.

: Vibrates for incoming voice calls or videophone calls, and vibrates for

incoming mail, chat mail or Messages R/F.

(about 0.5 second).

(about 1 second).

Sound/Screen/Light Settings

Information

pThe priority order of vibrators is as follows: “Setting for Phonebook entry” → “Group

setting” → “Vibrator”.

pEven when “Melody linkage” is set, the FOMA phone vibrates with “Pattern 2” if an

i-motion movie or melody with no vibration pattern is set for the ring tone.

pBe careful not to leave the FOMA phone on a desk or similar places with the vibrator

activated; when a call comes in, the FOMA phone might move and fall by vibration.

+m-5-5

Using Recorded Sound as Ring Tone

You can set the sound you recorded with the FOMA phone for a ring tone (including a ring tone for Number B of 2in1), On hold tone/Holding tone, alarm for “Alarm”, “Schedule”, “ToDo”, and “Book program”, and an answer message for Record Message. You can record only one item for about 15 seconds.

mLifeKitRec.msg/voice memoVoice announce

Record

pTo suspend recording midway, press Oo(), h, or r. The contents

recorded to that point are saved.

pThe tone beeps about 5 seconds before the recording time (for about 15

seconds) ends. When recording ends, the tone beeps twice, and the former

Sound/Screen/Light Settings

display returns.

pThe recording is suspended when a call comes in, when an alarm for “Alarm”,

“Schedule”, “ToDo”, “Book program”, or “Timer recording” sounds, or when you switch displays using Multitask during recording. (The contents recorded to that point are saved.)

pTo play back the recorded sound, select “Play”. To suspend playback midway,

press Oo(), h, or r.

pTo erase the recorded sound, select “Erase”, then select “YES”.

Changing Calling Tone

Melody Call is a service that changes the ringing tone phone callers hear, to a melody you like. For details, refer to “Mobile Phone User’s Guide [Network Services]”.

pMelody call is a pay service which is available on a subscription basis.

mSettingsMelody Call settingYES

Operate following the instructions on the display.

Information

pMelody Call is not available for incoming videophone calls. pWhen you select “YES” from the confirmation display asking whether to connect to the

site, the line is connected to the i-mode site. You are not charged a packet communication fee for connecting to the site for settings, however, you are charged for connecting to the IP site, i-mode menu site, and free melody corner.

+m-3-0

Setting Keypad Sound

mSettingsSoundKeypad soundON or OFF

Information

pYou cannot change the volume for keypad sound. pIf you set this function to “OFF”, the battery level tone (see page 43) and respective

warning tones do not sound.

pThe keypad does not make a sound when you press .<, during ringing, or during

playback of a moving image or i-motion movie.

pWhen you press .> with the FOMA phone closed, the FOMA phone works following

“Info notice setting” on page 107.

Setting Charging-start/end Tones

The confirmation tone sounds twice when charging starts/ends.

mSettingsOther settingsBatteryCharge sound

ON or OFF

Information

pYou cannot change the volume for charge sound. pThe charging confirmation tone does not sound when a display other than the

Stand-by display is shown or during Manner Mode or Public Mode (Drive Mode).

+m-7-5

Sounding Alarm when a Line is Likely to be Disconnected

When a call is likely to be disconnected midway due to bad radio wave conditions, an alarm sounds to inform you right before disconnection.

mSettingsTalkQuality alarmSelect an alarm.

No tone . . . . . Does not sound.

High tone . . . High alarm sounds.

Low tone . . . . Low alarm sounds.

Information

pYou might be disconnected without hearing an alarm if radio wave conditions

deteriorate suddenly.

pAn alarm for “Quality alarm” sounds only from the earpiece during a videophone call.

+m-6-8

Setting Ring Time for Mail and Messages R/F

You can set the duration of the ring tone which sounds for incoming i-mode mail, SMS messages, Chat mail and Messages R/F.

mSettingsSoundMail/Msg. ring time

Select a type of mail or messageON or OFF Enter a ring time (seconds).

pEnter in two digits from “01” through “30”.

+m-5-1

Sounding Ring Tone from Earphone Only

You can set where you make the ring tone and alarm sound from for when you connect an earphone/microphone (option).

mSettingsSoundHeadset usage setting

Headset and speaker or Headset only

Information

pEven when you set “Headset only”, the ring tone sounds from both the earphone and

speaker about 20 seconds after ring ing starts. However, the tone does not sound from the speaker but sounds from the earphone only even after 20 seconds have elapsed if the tone sounds for the operations other than incoming calls, incoming mail, and alarm notification.

pEven when you set “Headset only”, the tone sounds from the speaker when you do

not connect any earphone/microphone or when you start shooting still or moving images.

Sound/Screen/Light Settings

Information

pIn the following cases, the tone sounds from the earphone when an earphone/

microphone is connected, and from the speakers when it is not connected, regardless of this setting:

・While watching a 1Seg program ・During playback of a video file ・During playback of an i-motion movie ・During playback of a melody ・While an i-αppli program is running ・During playback of a music file by MUSIC Player ・During playback of a Music&Video Channel program

pDo not wind the cord of the earphone/microphone around the FOMA phone. pThe FOMA phone may pick up noise if you take the cord of the earphone/microphone

close to the FOMA phone during a call.

Silencing Tones from FOMA Phone

Just by pressing a key, you can set to silence tones such as a ring tone and keypad sound from the FOMA phone. You can use “Manner mode set” to select Manner Mode functions from three types; “Manner mode”, “Super silent”, or “Original”. While “Manner mode” or “Super silent” is activated, or while “Mic sensitiv.” is set to “Up” in “Original”, you can talk softly on the phone but your voice can still be heard clearly at the other end.

Sound/Screen/Light Settings

During standby/During a call

s(for at least one second)

Manner mode selected in “Manner mode set” is set. pWhen the FOMA phone is closed, press and hold > for at least one second to

activate Manner Mode.

pDuring Manner Mode, “ ” is displayed. The settings you selected for “Manner

mode set” are also displayed.

: Indicates that “Vibrator” will work to notify events.

/ / : Indicate that “Ring volume” has been set to “Silent”.

Information

pIf you activate Manner Mode during a call or calling, the message to that effect

appears.

pThe recording start tone sounds even in Manner Mode when you shoot still images or

moving images.

Information

pIn Manner Mode, if you try to play back a melody, the confirmation display appears

asking whether to play it back. Select “YES” to play back the melody at the volume set for “Phone” of “Ring volume”. If the setting is “Silent” or “Step”, the volume is Level 2.

pIn Manner Mode, if you do the following operations, the confirmation display appears

asking whether to play back voice or music.

・Watching a 1Seg program ・Playing back an i-motion movie ・Playing back a video file ・Playing back a music file by MUSIC Player ・Playing back a Music&Video Channel program

Select “YES” to play it back at the volume set for each player. When you change the volume level, it is played back at the set volume for the next time.

pWhen an earphone/microphone (option) is connected, the sound comes out of the

earphone. The confirmation display asking whether to play back sound or music files during Manner Mode does not appear. Further, the playback tone does not sound from the speakers even if you unplug the earphone/microphone during playing back sound or music files by each player.

To release Manner Mode

Press and hold s for at least one second. During a call or calling, two beeps sound and the message that is released appears. pWhen the FOMA phone is closed, press and hold > for at least one second to release

Manner Mode.

To activate Manner Mode during ringing

Press l() or >. Manner Mode is activated and Record Message is simultaneously activated so that the caller can leave a voice/video message. Even when “Record message setting” has not been set to “ON”, the Record Message function works. Press d or Oo( ) to answer a voice call, and press d or +Oo( ) to answer a videophone call. pWhen five messages for voice calls and two messages for videophone calls have

already been recorded, Record Message does not work. Manner Mode specified by ”Manner mode set” works.

pAfter you finish a call, Manner Mode is still activated.

+m-2-0

Selecting Manner Mode Type

You can select one of three types of operations for Manner Mode.

■Operations during Manner Mode

Record message

※1

Vibrator Phone volume Silent Silent through Level 6 and step① Mail volume Silent Silent through Level 6 and step② Alarm volume VM tone ON OFF ON or OFF③ Keypad sound OFF ON or OFF④ Microphone sensitivity Up Normal or Up

Low voltage alarm tone (Low battery alarm)

Confirmation tone for selecting ring tone On hold tone Silent Holding tone Silent ToruCa obtained tone and ToruCa failed-to-obtain tone Confirmation tone for recording voice announce Battery level tone Silent Silent Voice recognition start tone Silent Silent Confirmation tone for checking missed calls and new mail Playback tones of attached melody Effect tones of Decome-Anime Warning tones Silent Works with the same set value as ④. Schedule alarm Silent Works with the same set value as ①.

※2

Manner

Super

Mode

Silent

Set value of

Record message

ON ON or OFF

Silent Silent through Level 6 and step

OFF

Silent

Silent Works with the same set value as ①.

ON OFF Works with the same set value as ③.

Silent

Silent Silent

When “LVA tone” is set to “ON”, it

works with the same set value as ①.

Works with the same set value as ①・

Works with the same set value as ①. Works with the same set value as ①.

Works with the same set value as ①.

Original

ON or OFF

②.

Manner

Super

Mode

ToDo alarm Silent Works with the same set value as ①. Alarm for Book program Silent Alarm for Timer recording Silent Start tones for shooting still and moving images Confirmation tone for selecting shutter sound Switching to Hands-free by “Hands-free w/ V. phone”

Read aloud volume Silent

Effect tones of Flash movies

※1 Vibrator works for the following tones:

Ring tones and alarm tones for “Alarm”, “Schedule”, “ToDo”, “Book program” and “Timer recording”

The vibration pattern is the same as the setting you set on page 93. However, if

※3

※4 ※5

※6

the setting you set on page 93 is “OFF”, “Pattern 2” applies.

Confirmation tone for checking missed calls and new mail

The FOMA phone vibrates for about 1 second when you have missed calls or new mail messages and vibrates for about 0.2 second when you have no missed calls and new mail messages.

※2 When “Prefer manner mode” on page 361 is set to “OFF”, the tone sounds at the

volume set for Alarm.

※3 The tone sounds at Level 1 when ①is “Silent”. ※4 The tone sounds at Level 2 when ①is “Step”. ※5 The tone sounds at Level 1 when①is not “Silent”. ※6 The tone sounds at Level 6 when①is not “Silent”. ※7 When “Prefer manner mode” on page 272 is set to “OFF”, the tone sounds at the

volume set for Book Program.

※8 The tone does not sound when①is “Step”.

Silent

Works with the same set value as ①. Works with the same set value as ①.

Level 4 Level 4

OFF

OFF OFF

Silent Silent

Works with the same set value as ①.

Works with the same set value as

“Read aloud volume” on page 359.

Original

※7 ※8

※4

Sound/Screen/Light Settings

You can select from among standard “Manner mode” to inform you of incoming calls or mail by the vibrator, “Super silent” to erase sounds including confirmation tones from the earpiece, or “Original” to customize operations.

mSettingsIncoming callManner mode set

Manner mode, Super silent or Original Do the following operations.

Item Operation/Explanation

Record msg. ON or OFF

Vibrator You can set the FOMA phone to vibrate for incoming calls and

Phone vol. You can adjust the ring volume for incoming voice calls and

Sound/Screen/Light Settings

Mail vol. You can adjust the ring volume for i-mode mail, SMS messages,

Alarm vol.

VM tone You can set the FOMA phone to sound a confirmation tone when

Keypad sound ON or OFF

Mic sensitiv. Normal or Up

pEven if you select “ON”, the ring time is fixed to about 13

seconds and cannot be changed when “Record message setting” on page 69 is set to “OFF”.

pSee page 69 for Record Message Setting.

mail.

ON or OFF

pSee page 93 for Vibrator.

videophone calls.

Use Bo to adjust the volume.

pSee page 65 for Ri ng Volume.

and Messages R/F.

Use Bo to adjust the volume.

pSee page 65 for Ri ng Volume.

Use Bo to adjust the volume.

pSee page 360 for Alarm.

a record message is played back, a voice memo is recorded or played back, and a movie memo is recorded.

ON or OFF

pSee page 94 for Keypad Sound.

Item Operation/Explanation

LVA tone ON or OFF

pSee page 43 for LVA Tone (low battery alarm).

Press l().

Changing Displays

Set Stand-by Display

You can set an image for the Stand-by display. You can set also i-motion movies shot by the FOMA phone or downloaded from sites for the Stand-by display.

mSettingsDisplayDisplay setting

Stand-by displaySelect a type of image.

pIf you select “Calendar/schedule”, select a display format, and then select “BG

image ON” or “BG image OFF”. If you select “BG image OFF”, the setting is completed.

pIf you select “iαppli display”, select an i-αppli program. The setting is completed.

Select a folderSelect an image.

pOn the Stand-by display, the image smaller than the display is shown in

equivalent dimensions or enlarged to fit to the display size, depending on the image size.

pSee page 167 when you select “i-mode srch”.

+m-5-6

Docomo Style P-06A Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Before using your FOMA phone

Easy Search/Contents/Precautions

How to Read/Refer to This Manual

Easy Search

Contents

Main Functions of P-06A

Making Full Use of P-06A!

Safety Precautions

Notes on Handling

Intellectual Property Rights

Accessories and Main Options

Before Using the Handset

Phone Parts and Functions

Navigation Displays and Key Operations

Display

Displaying Description of Icons

Private Window

Method for Selecting Menu

Using Simple Menu

When You do not Remember Key Operation

Using UIM (FOMA Card)

Attaching/Removing Batteries

Charging

Opening FOMA Phone by Using a Button

Checking Battery Level

Turning Power On/Off

Switching to English

Executing Initial Settings

Setting Date and Time

Displaying World Time

Notifying the Other Party of Your Phone Number

Checking Your Own Number

Voice/Videophone Calls

About Videophone

Making a Call/Videophone Call

Switching between a Voice Call and a Videophone Call

Using Call Records

Using Chaku-moji

Notifying/Not notifying Your Phone Number by Call

Sending Touch-tone Signals

International Calls

Setting for International Calls

Storing Numbers to be Added to the Beginning of a Phone Number

Making a Call with Specified Sub-address

Setting Alarm for Reconnecting

Making Voice Clear According to Surrounding Noise

Reducing Surrounding Noise to Make Voice Clear

Slowing Down the Other Party’s Speaking Speed

Switching to Hands-free

Using Hands-free Compatible Devices

Receiving a Call/Videophone Call

Switched between a Voice Call and a Videophone Call by the Other Party

Setting Response of Key Operation for Answering Incoming Calls

Setting Response for when Opening FOMA Phone during Ringing

Setting Response for when Closing FOMA Phone during a Call

Adjusting Earpiece Volume

Adjusting Ring Volume

Putting an Incoming Call on Hold when You cannot Answer at Once

Putting a Call on Hold during a Call

Setting Hold Tone

Using Public Mode (Drive Mode)

Using Public Mode (Power Off)

If You could not Answer an Incoming Call

Recording Voice/Video Messages when You cannot Answer the Call

Recording Voice/Video Messages when You cannot Answer the Call during Ringing

Playing Back/Erasing Record Messages/a Voice Memo/Videophone Record Messages/Movie Memos

Using Chara-den

Useful Functions for Videophone Calls

Setting Videophone Hands-free

Setting Image Quality for Videophone Calls

Changing Image Displays for Videophone Calls

Redialing as a Voice Call when a Videophone Call cannot be Connected

Setting for Switching between a Voice Call and a Videophone Call

Selecting Response to Incoming Videophone Calls during i-mode

Connecting FOMA Phone to External Devices to Use Videophone Function

Phonebook