F-01D
INSTRUCTION MANUAL
’11.9
Thank you for purchasing "F-01D" mobile terminal.
Introduction
Before using your terminal, or when necessary, read
this manual to ensure safe use and handling.
･
･
･
･
･
Before using the terminal
F-01D supports LTE, W-CDMA, GSM/GPRS, Wireless
LAN System.
Because your terminal uses wireless transmission, it
may not function in locations where it is difficult for
radio waves to penetrate, such as tunnels, underground
passages and some buildings, in areas where radio
waves are weak, or out of Xi and FOMA service area.
Even when you are high up in a tall building or
condominium and nothing blocks your view outside,
your terminal may not be able to receive or transmit
signals. Also, communication may be interrupted even
when the signal status icon on your terminal indicates
there are strong radio waves and you are not moving
(traveling).
Your terminal makes wireless communication. When
you are operating your terminal while moving to a
location subject to weaker radio wave conditions, the
transmitted digital data may not be correctly decoded
and as a result the received contents may differ
somewhat from the actual contents.
Maintain a separate record of the data (Contacts,
Schedule, Memo, etc.) you saved in the terminal. Note
that DOCOMO assumes no responsibility for any loss of
saved contents of data resulting from malfunction,
repair, changing of the model or other handling of the
terminal.
In the terminal, as it is for a PC, some applications that
you install may give instability of the operation, or may
send your location information or personal information
registered to the terminal to outside via the Internet and
the information may be used improperly. Please
thoroughly check a provider and operation status of the
application etc. which you want to use beforehand and
then use it.
･
You are recommended to save important data to
microSD card.
･
This terminal supports Xi Area, FOMA Plus-Area and
FOMA HIGH-SPEED Area.
SIM unlock
This terminal supports SIM unlock. If you release SIM lock,
you can use SIM by a carrier other than NTT DOCOMO.
･
The SIM unlock service is provided at a docomo Shop.
･
A SIM unlock charge is separately required.
･
If you use a SIM other than by DOCOMO, you cannot use
LTE system. Available services and functions will be
limited. DOCOMO is not liable to any failures or
malfunctions.
･
For details of SIM unlock, refer to NTT DOCOMO
website.
About manuals for F-01D
"Quick start guide" (in Japanese only)
This manual provides information about screens and
operations of basic functions.
"Instruction Manual” (installed in the terminal)
This manual provides information and operations of all
the functions. (In Japanese only)
In the Applications menu, [Instruction Manual]→Select a
search method
This manual provides information and operations of all
the functions.
〈
manual/download/index.html
*You can download the latest information.
"Instruction manual" (PDF file)
From PC〉 http://www.nttdocomo.co.jp/support/trouble/
Accessories and main options
<F-01D and included accessories>
F-01D (including warranty)
<Main options>
FOMA charging microUSB adapter T01
(with manual)
FOMA AC adapter 01/02
(with warranty and manual)
Quick start guide
(Japanese)
AC Adapter F05 (with warranty)
Desktop Holder F35 USB Cable
電子辞書データDVD
(E-dictionary data DVD)
(Sample)
for PC connection T01
Other options→P101
･
In this manual, "F-01D" mobile terminal is usually
referred to as "the terminal".
･
The images or illustration used in this manual are
examples. They may differ from the actual displays.
･
In this manual, "authenticate" indicates the
operating procedure for entering the terminal
security code in 4-8 digits (→P42).
･
Unauthorized copying of parts of or this entire
manual is prohibited.
･
The contents in this manual, URL and contents are
subject to change without prior notice.
1
Contents/Precautions
Contents
■
Accessories and main options .........................1
■
Important precautions on using F-01D ............4
■
Precautions (Always follow these directions)
.............................................................................5
■
Handling precautions ......................................11
■
Waterproofness ...............................................15
Before using the terminal ....... 19
Part names and functions........................................ 19
docomo mini UIM card............................................ 20
microSD card............................................................ 21
Charging ................................................................... 21
Power ON/OFF.......................................................... 24
Basic operation (Using touch panel) ...................... 24
Hand gesture control ............................................... 25
Initial setting ............................................................. 27
Screen/Icon ............................................................... 27
Home screen............................................................. 29
Applications screen.................................................. 30
Character Entry......................................................... 33
Lock/Security ............................................................ 42
Contacts.................................. 47
Using Contacts ......................................................... 47
PhoneBookCopy....................................................... 49
Editing owner info.................................................... 49
Settings................................... 50
Setting menu.............................................................50
Wireless & networks.................................................50
Sound settings ..........................................................56
Screen settings..........................................................58
Applications...............................................................59
Accounts & sync .......................................................60
Privacy .......................................................................61
Storage ......................................................................62
Searching the terminal or sites................................62
High-performance unified search............................63
Language & input .....................................................63
Accessibility...............................................................65
Date & time................................................................65
About phone..............................................................66
Mail/Internet............................ 67
sp-mode mail ............................................................67
SMS............................................................................67
Email ..........................................................................69
Gmail..........................................................................71
Early warning "Area Mail"........................................72
Google Talk ...............................................................73
Browser......................................................................73
2
Contents/Precautions
File management..................... 76
Bluetooth communication .................................... 76
Connecting an external device................................ 78
Applications............................ 79
Camera...................................................................... 79
Gallery....................................................................... 81
Music player ............................................................. 81
Stereo earphones..................................................... 83
YouTube.................................................................... 83
Android Market ........................................................ 84
docomo market ........................................................ 86
GPS/Navigation ........................................................ 86
1Seg .......................................................................... 89
Link with DLNA compatible device......................... 93
Clock.......................................................................... 95
Calendar.................................................................... 95
Calculator.................................................................. 96
Electronic dictionary ................................................ 96
Document Viewer..................................................... 97
International roaming ............. 98
Outline of international roaming (WORLD WING)
....................................................................................98
Available service overseas.......................................98
Before using the terminal overseas ........................99
Settings for international roaming........................100
After returning to Japan.........................................100
Appendix/Index ..................... 101
Options and related devices ..................................101
Troubleshooting (FAQ)...........................................101
Warranty and After-Sales Service .........................104
Software update......................................................106
Main specifications.................................................109
Authentication and compliance.............................111
Declaration of Conformity......................................111
Federal Communications Commission (FCC) Notice
..................................................................................111
FCC RF Exposure Information................................112
Important Safety Information ................................113
About Wi-Fi..............................................................113
Export Administration Regulations....................... 114
Intellectual Property Right......................................114
Index ........................................................................118
3
Contents/Precautions
Important precautions on using F-01D
･
The terminal does not support i-mode sites (programs)
or i-αppli.
･
Google applications and service contents are subject to
change without prior notice.
･
The terminal automatically performs communication for
some functions, for example, to synchronize data, check
the latest software, maintain connection with the server.
If you transmit a large amount of data such as
downloading applications or watching video, a packet
communication charge becomes high. Subscription of
packet flat-rate service is highly recommended.
･
Setting the terminal to manner mode does not mute
sounds (playback of video or music, alarm, etc.) other
than the ringtone, operation sound, and notification
sounds.
･
You can check your phone number (own number) in the
following steps.
From the Applications menu, [Settings]→[About phone]
→
[Profile]
･
The software on the terminal can be updated with the
latest information.→P106
･
Improving the terminal's quality or upgrading operation
system may be included in the software update. And
some applications used in the previous version may not
be available or some unintended bugs may occur after
software update.
･
When the memory space of the microSD card or the
terminal is almost full, running application may not
operate normally. In this case, delete saved data.
･
Set the screen lock password to ensure the security of
your terminal for its loss.→P44
･
For the information on the services provided by Google,
refer to the terms of use for Google Inc. And for the
details on other web services, read terms of use for each
service.
･
A docomo mini UIM card is only available for the
terminal. If you have a UIM or FOMA card, bring it to
docomo Shop to replace.
･
If your terminal is lost, change your each account
password using a PC to prevent other persons from
using Google services such as Google Talk, Gmail,
Android Market, etc., or Twitter, Facebook, etc.
･
The terminal supports only sp-mode, mopera U and
Business mopera Internet (VPN setting is limited only to
PPTP). Other providers are not supported.
･
The battery is built-in the terminal and cannot be
changed by yourself.
･
The terminal does not support voice call and digital
communications (videophone, 64K data
communication).
･
To use tethering, a subscription to sp-mode is required.
･
When using tethering, packet communication charges
may become high. Subscription of packet flat-rate
service is highly recommended.
･
If you use packet flat-rate service, when tethering is
enabled, all packet communications including browser
and mail, etc. become "communications by connecting
to an external device such as a PC", even when any
external device is not connected. Be sure to disable
tethering after use.
･
For details on usage fee, refer to http://
www.nttdocomo.co.jp/english/.
4
Contents/Precautions
Precautions (Always follow these directions)
・
Before using your terminal, or when necessary, read the
precautions below to ensure safe use and handling.
After reading this manual, keep it carefully.
・
These precautions are intended to protect you and
others around you. Read and follow them carefully to
avoid injury, damage to the product or damage to
property.
・
The signs below differentiate between the levels of
danger that can occur if the product is not used within
the specified guidelines.
This sign denotes that death
or serious injury may directly
DANGER
WARNING
CAUTION
・
The symbols below show specific directions.
This symbol denotes that the action is
prohibited.
Don’t
This symbol denotes that disassembling the
phone or its components is not allowed.
No disassembl y
result from improper use.
This sign denotes that death
or serious injury may result
from improper use.
This sign denotes that minor
injury or damage to property
may result from improper use.
This symbol denotes that using the phone
or its components with wet hands is not
No wet hands
allowed.
This symbol denotes that using the phone
or its components in a bathroom or other
No liquids
highly humid area is not allowed.
This symbol denotes that an instruction
must be obeyed at all times.
Do
This symbol denotes that the equipment
should be unplugged.
Unplug
■
Precautions contain the description below.
Handling the terminal, adapter, desktop holder and
docomo mini UIM card (common).................................. 5
Handling the terminal ..........................................................7
Handling adapter and desktop holder ................................ 9
Handling docomo mini UIM card...................................... 10
Handling mobile phones near electronic medical
equipment ....................................................................... 10
Material list .........................................................................11
◆
Handling the terminal, adapter,
desktop holder and docomo mini UIM
card (common)
DANGER
Do not use, store, or leave the equipment in
hot areas such as near flames or in areas
under strong direct sunlight such as inside a
Don’t
vehicle.
May cause fire, burns or injuries.
5
Contents/Precautions
Do not put the terminal into heating cooking
device such as microwave oven or highpressure container.
Don’t
May cause fire, burns, injuries, electric shock.
Do not disassemble or remodel the
equipment.
May cause fire, burns, injuries, electric shock.
No disassembl y
Do not let the terminal get wet with water,
drinking water, urine of pet animals, etc.
May cause fire, burns, injuries, electric shock.
No liquids
For waterproofness, refer to the page.
Use the adapter specified by NTT DOCOMO
for your terminal.
May cause fire, burns, injuries, electric shock.
Do
WARNING
Do not throw the equipment or give hard
shock to it.
May cause fire, burns, injuries, electric shock.
Don’t
Keep conductive materials (metal pieces,
pencil lead, etc.) from coming in contact with
the charging jack or external connection jack.
Don’t
Do not put those materials inside the
terminal.
May cause fire, burns, injuries, electric shock.
Do not cover or wrap the terminal with a
blanket, etc. while using or charging.
May cause fire or burns.
Don’t
Turn the terminal OFF and stop charging
before entering a place such as a gas station
Do
where flammable gases are generated.
The gas may catch fire.
If the equipment starts giving off a strange
smell, overheats, becomes discolored or
Do
deformed during use, charging or in storage,
immediately perform the following
operations.
･
Remove the power plug from the wall outlet or
cigarette lighter socket.
･
Turn the terminal OFF.
May cause fire, burns, injuries, electric shock.
→
P15
Do not leave the equipment on unstable or
sloping surfaces.
May cause injuries.
Don’t
Do not store the equipment in extremely
humid, dusty or hot areas.
May cause fire, burns, electric shock.
Don’t
Children using the equipment should be
instructed in proper operation by an adult. Do
Do
not allow them to use the equipment without
adult supervision.
May cause injuries.
Store the equipment out of reach of small
children.
May be accidentally swallowed or cause injuries.
Do
Be careful especially when using the terminal
connected to the adapter continuously for a
Do
long time.
If you use applications, watch 1Seg, etc. while
charging for a long time, the terminal and adapter
may be heated.
Directly touching a hot part for a long time, you may
have redness, itching or rash on your skin, or it may
result in low-temperature burns depending on your
constitution and/or health condition.
CAUTION
6
Contents/Precautions
◆
Handling the terminal
■
The internal battery for the terminal is as follows.
Display Type of battery
Li-ion 00 Lithium polymer battery
DANGER
Do not throw the battery pack into the fire.
May cause internal battery to ignite, burst, heat or
leak.
Don’t
Do not nail the battery pack, hit with a
hammer or step on it.
May cause internal battery to ignite, burst, heat or
Don’t
leak.
If the internal battery's fluid etc. contacts
eyes, immediately flush the eyes with clean
Do
water and see a doctor right away. Do not rub
the eyes.
May cause loss of sight.
WARNING
Do not put foreign objects such as liquid like
water, metal pieces or burnable things into
docomo mini UIM card or microSD card slot.
Don’t
May cause fire, burns, injuries, electric shock.
Turn the terminal OFF in areas where use is
prohibited, such as in airplanes and hospitals.
May cause electronic equipment or electronic medical
Do
equipment to fail or malfunction.
When using the phone in a medical facility, be sure to
observe the regulations of the facility.
If you do prohibited act such as using the phon e in an
airplane, you will be punished according to law.
If usage of mobile phones in an aircraft is admitted by
setting airplane mode, etc., use the terminal under the
direction of the airline.
When ringtone is sounding, etc. keep the
terminal away from your ear. And, when
Do
connecting the earphone/microphone etc. to
the terminal and play a game or music, adjust
the volume moderately.
Too loud volume may cause a hearing loss.
And, if you cannot hear the sound around you clearly,
it may cause an accident.
If you have weak heart, be careful when
setting the Vibrate alert (vibration) or alert
Do
volume setting.
May cause harmful effect on heart.
When you use electronic medical equipment,
check with the equipment manufacturer to
Do
determine how the device is affected by radio
waves before using.
May cause harmful effect on electronic medical
equipment etc.
Turn the terminal OFF near high-precision
electronic control equipment or electronic
Do
equipment using low-power signals.
May cause the equipment to fail or malfunction.
Examples of electronic equipment t o avoid.
*
Hearing aids, implanted pacemakers or defibrillators, other
electronic medical equipment, fire alarms, automatic doors
and other automatic control e quipment.
Users wearing implanted pacemakers or defibrillators or
other electronic medical e quipment should check with the
manufacturer or sales outlet about t he effect of radio
frequencies on the equipment.
When the display or camera lens is
accidentally broken, be careful of broken
Do
glass or exposed internal parts of the
terminal.
Surface of display is made of ABS resin, and surface
of camera lens is made of high strength acrylate resin
parts and they are structured for the glass not to
scatter, however, if you mistakenly touch broken or
exposed parts, you may be injured.
7
Contents/Precautions
If the internal battery leaks or gives off a
strange smell, immediately remove it from
Do
the vicinity of open flames.
The vapors from leaking battery pack fluid may ignite
or explode.
CAUTION
Do not use damaged terminal.
May cause fire, burns, injuries, electric shock.
Don’t
When using the motion sensor, check the
safety around you, hold the terminal firmly,
and do not shake it unnecessarily.
Don’t
May cause accident such as injuries.
If the display part is accidentally broken and
the liquid crystal leaks out, do not make the
substance contact with your skin of face or
Don’t
hands.
May cause loss of sight or skin problems.
If the liquid crystal gets into your eyes or mouth, rinse
it with clean water and see a doctor immediately.
And, if the liquid adheres to skin or clothing, use
alcohol etc. to wipe it off, then wash with soap.
Do not discard old battery packs together
with other garbage.
May cause igniting or environmental destruction.
Don’t
Bring the old terminal into a sales outlet such as
docomo Shop. If your local municipality has a
recycling program, dispose of terminal as provided
for.
To use the terminal in car, check with
automobile manufacturer or dealer to
Do
determine how the device is affected by radio
waves before using.
In rare cases, using the phone in some vehicle models
can cause the vehicle's electronic equipment to
malfunction. In that case, stop using the terminal
immediately.
The use of the terminal may cause itching,
rashes, eczema, or other symptoms
Do
depending on the user's physical condition. If
you develop skin problems, stop using the
phone immediately, and see a doctor.
"Material list (P11)"
When watching the display, take a certain
distance from the display in a fully bright
Do
place.
May reduce visual acuity.
If fluid etc. leaks out from the internal battery,
do not make the fluid contact with your skin
Do
of face or hands.
May cause loss of sight or skin problems.
If the fluid etc. put into your eyes or mouth, or contacts
skin or clothes, immediately flush the contacted area
with clean water.
If the fluid etc. put into the eyes or mouth,
immediately see a doctor after flushing.
→
8
Contents/Precautions
◆
Handling adapter and desktop holder
WARNING
Do not use the adapter cord if it gets
damaged.
May cause fire, burns, electric shock.
Don’t
Do not use the AC adapter or desktop holder
in a bathroom or other highly humid area.
May cause fire, burns, electric shock.
Don’t
Always use the DC adapter with a negativeground vehicle. Do not plug it into a positiveground vehicle.
Don’t
May cause fire, burns, electric shock.
When it starts to thunder, do not touch
adapter.
May cause electric shock.
Don’t
Do not short the charging jack while it is
connected to the outlet or cigarette lighter
socket. Do not touch the charging jack with a
Don’t
part of your body such as your hand or finger.
May cause fire, burns, electric shock.
Do not place heavy objects on the adapter
cord.
May cause fire, burns, electric shock.
Don’t
When you insert and remove the AC adapter
from power outlet, do not contact a metal
strap or other metal objects with the jack.
Don’t
May cause fire, burns, electric shock.
Do not touch the adapter cord, desktop
holder or outlet with wet hands.
May cause fire, burns, electric shock.
No wet hands
Only use with the specified power source and
voltage. When charging the terminal
Do
overseas, use AC Adapter for global use.
If incorrect voltage is used, this may cause fire, burns
or electric shock.
AC adapter : AC100 V
DC adapter : 12 or 24V DC (specific for negative
ground vehicle)
AC adapter for global use : Between 100V and 240V AC
(Connect to the AC outlet for internal household
use)
If the DC adapter's fuse blows, replace it only
with the specified fuse.
May cause fire, burns, electric shock. For the specified
Do
fuse, see the instructions that come with the DC
adapter.
Wipe off any dust that accumulates on the
power plug.
May cause fire, burns, electric shock.
Do
When you connect the AC adapter to an
outlet, firmly connect to the outlet.
May cause fire, burns, electric shock.
Do
When you disconnect the power plug from
the outlet or cigarette lighter socket, do not
Do
pull the adapter cord with excessive force.
Instead, hold the adapter to disconnect.
May cause fire, burns, electric shock.
Always remove the power plug from the
outlet or cigarette lighter when not using the
Unplug
adapter for an extended period.
May cause fire, burns, electric shock.
Immediately remove the power plug from the
outlet or cigarette lighter socket if water or
Unplug
other fluids get into the adapter.
May cause fire, burns, electric shock.
Always remove the power plug from the
cigarette lighter socket when cleaning the
Unplug
equipment.
May cause fire, burns, electric shock.
9
Contents/Precautions
◆
Handling docomo mini UIM card
CAUTION
Be careful of the cut surface when removing
docomo mini UIM card.
May cause inju ries.
Do
◆
Handling mobile phones near
electronic medical equipment
■
These precautions are based on the guidelines
produced at the Electromagnetic Compatibility
Conference Japan, regarding the protection of
electronic medical equipment from radio waves
emitted by mobile phone units.
WARNING
Obey the following rules inside medical
facilities.
･
Do not bring the terminal into operating rooms
Do
(ORs), intensive care units (ICUs) or coronary ca re
units (CCUs).
･
Turn the terminal OFF in hospital wards.
･
Turn the terminal OFF in hospital lobbies and
corridors if electronic medical equipment could be
nearby.
･
If the medical facility has specified zones where use
or possession of mobile devices is prohibited, obey
those instructions.
Turn the terminal OFF in crowded trains or
other public places where pacemaker or
Do
defibrillator wearers could be nearby.
The terminal's signals may affect the operation of
implanted pacemakers or defibrillators, and other
devices.
Wearers of implanted pacemakers or
defibrillators must carry and use the terminal
Do
at least 22 cm away from the implanted
device.
The terminal's signals may affect the operation of
implanted pacemakers or defibrillators, and other
devices.
When electronic medical equipment other
than implanted pacemakers or defibrillators
Do
are in use outside of medical facilities (such
as in home care settings), check with the
device manufacturer to determine how the
device is affected by electrical signals.
The terminal's signals may affect the performance of
electronic medical equipment.
10
Contents/Precautions
◆
Material list
Part Material
Exterior
case
Touch panel Hardened
Camera panel High-
Power key ABS resin Tin plating
Volume button ABS resin Tin plating
Stereo earphone jack PA resin None
Jack cap/
Slot cap
External connection jack Stainless
Charging
jack
Front case ABS resin UV hard coating
Back case PC+ABS
Body PC resin UV hard coating
Flexure Elastomer
Water stop Silicon
Contacts Stainless
Attaching
holder
section
resin
glass
strength
acrylate
resin
resin (PE)
rubber
steel
steel
LCP resin None
Surface
treatment
UV hard coating
AF coating
UV hard coating
None
None
Tin plating
Gold plating
Handling precautions
◆
General
・
F-01D is waterproof, however, do not allow water to
seep into the terminal and do not allow accessories or
optional devices to get wet.
- Adapter, desktop holder, docomo mini UIM card are
not waterproof. Do not use in a bathroom or other
highly humid area or do not let rain attached. Or
putting the terminal on your body, humidity of sweat
may cause internal corrosion and malfunction. Note
that malfunctions, which are determined to be caused
by water as result of inspections, are not covered by
the warranty. Since these conditions are outside the
scope of the warranty, a repair, if at all possible, is
charged.
・
Clean the terminal with a dry soft cloth (such as a cloth
for eyeglasses).
- Rubbing it roughly with a dry cloth may scratch the
display.
- Drops of water or dirt left on the display may cause
stains.
- If the terminal is wiped with alcohol, paint thinner,
benzine or detergent, the printing may disappear or
color may fade.
・
Clean the jack occasionally with a dry cotton swab etc.
- If the jack is soiled, connection gets worse and it may
cause power to be turned off or insufficient battery
charge, so clean the jack with a dry cotton swab etc.
Also, be careful never to damage the jack when
cleaning it.
・
Do not place the terminal near an air-conditioner outlet.
- The rapid change in temperature may cause
condensation, causing internal corrosion and
malfunction.
11
Contents/Precautions
・
When using, be careful not to subject excessive force to
the terminal, etc.
- If the terminal is crammed into a brimming bag,
display or internal PCBs may be damaged or
malfunction. And, if external devices are plugged into
the external connection jack (earphone/microphone
jack), the breakage of the connector or malfunction
may result.
・
Do not rub or scrape the display with a metal piece etc.
- May scratch the display, causing malfunction or
damage.
・
Carefully read the separate instructions that come with
the adapter.
◆
Terminal
・
Do not press the surface of the touch panel strongly or
operate it with sharp objects such as a nail, a ballpoint
pen and a pin.
- It may damage the touch panel.
・
Avoid extreme temperature.
- Use the terminal where the temperature ranges
between 5 and 35℃ and humidity ranges between 45
and 85%. For information when using in a bathroom,
see "What you can do with waterproofness of F-01D".
→
P15
・
The terminal may affect land-line phones, TVs or radios
in use nearby, so use it as far as possible from these
appliances.
・
Maintain a separate record of the data you saved in the
terminal.
- If the data is deleted, DOCOMO assumes no
responsibility for the loss of any data.
・
Do not drop the terminal or subject it to shocks.
- May cause malfunction or damage.
・
Do not plug external devices into the external
connection jack (earphone/microphone jack) at a slant,
or do not pull it forcibly while it is plugged.
- May cause malfunction or damage.
・
It is normal for the terminal to become warm during use
or charging. Continue to use it.
・
Do not leave the terminal with the camera in areas
under strong direct sunlight.
- May cause discoloring or burn-in of elements.
・
Use the terminal with the external connection jack cap
and slot cap closed.
- Dust and/or water brought into the terminal cause
troubles.
・
While microSD card is being used, do not take the card
out and do not turn off the terminal.
- May cause data loss or malfunction.
・
Do not bring magnetic cards etc. close to the terminal.
- Magnetic data in cash cards, credit cards, telephone
cards, floppy disks, etc. may be erased.
・
Do not bring magnetized objects close to the terminal.
- Bringing strong magnetism close may cause a
malfunction.
・
The internal battery is a consumable part.
- Replace the internal battery if the terminal has
extremely short operation time on a full charge,
though it may vary by operating conditions. For
replacement of the internal battery, contact "Repairs"
on the last page of the instruction manual (in Japanese
only) or a DOCOMO-specified repair office.
・
Charge the battery in an area within the proper ambient
temperature range (5-35℃).
・
The operation time provided by the internal battery
varies by the operating environment and internal
battery's deterioration.
・
Be careful especially about the following points when
preserving the internal battery.
- Keeping under the state of the full charge (right after
charging ends)
- Keeping under the state of the empty charge (too
exhausted to turn on the terminal)
They may cause the internal battery performance to be
degraded or its lifetime to be shortened.
A recommended battery level to keep the battery pack is
approximately 40 % of remaining battery level as a
guide.
12
Contents/Precautions
◆
Adapter
・
Charge the battery in an area within the proper ambient
temperature range (5-35℃).
・
Do not charge the battery in the areas below.
- In areas of excessive humidity, dust or vibrations
- Near land-line phones or TVs/radios
・
It is normal for the adapter to become hot while
charging. Continue to use it.
・
When using the DC adapter for charging, keep the
vehicle engine running.
- The vehicle's battery could become flat.
・
When using an outlet with a mechanism preventing
unplugging, follow the handling instructions for that
outlet.
・
Do not give strong shock. Do not deform the charging
jack.
- May cause malfunction.
◆
docomo mini UIM card
・
Do not use excessive force to install/remove docomo
mini UIM card.
・
Note that DOCOMO assumes no responsibility for
malfunctions occurring as the result of inserting and
using docomo mini UIM card with another IC card
reader/writer.
・
Always keep docomo mini UIM card ICs clean.
・
Clean docomo mini UIM card with a soft, dry cloth (such
as a cloth for eyeglasses).
・
Maintain a separate record of the data you saved in
docomo mini UIM card.
- If the data is deleted, DOCOMO assumes no
responsibility for the loss of any data.
・
To preserve the environment, bring the old docomo
mini UIM card to a sales outlet such as docomo Shop.
・
Take care not to scratch, touch accidentally or short IC.
- May cause data loss or malfunction.
・
Do not drop docomo mini UIM card or subject it to
shocks.
- May cause malfunction.
・
Do not bend docomo mini UIM card or place heavy
objects on it.
- May cause malfunction.
・
Do not install docomo mini UIM card into the terminal
with a label or sticker put on.
- May cause malfunction.
◆
Bluetooth devices
・
This terminal is equipped with the security features,
that are compliant with Bluetooth standards for
communication via Bluetooth. However, depending on
the settings, there may not be enough security. Be
aware of the communication using the Bluetooth
function.
・
DOCOMO assumes no responsibility for any
information which may be leaked during
communication via Bluetooth.
・
You can use headset, audio, keyboard, data transfer,
serial port, image transfer or health devices with the
terminal. An audio/video remote control may be
available with an audio device (only compatible
Bluetooth devices).
・
Frequency bands
Frequency bands used by the terminal Bluetooth
function are as below.
Frequency bands : 2400 MHz band
Modulation : FH-SS method
Expected interference distance : 10 m or shorter
Frequency changing possibility : All bandwidths
between 2400 MHz and 2483.5 MHz are used, and the
bandwidth used by mobile object identification devices
cannot be avoided.
13
Contents/Precautions
Cautions on using Bluetooth devices
In the bandwidth used by this terminal, in addition to home
electric appliances such as a microwave oven and industrial/
scientific/medical devices, in-plant radio stations used to
identify mobile objects used in production lines of a factory
that require a license, specified low power radio stations, or
amateur radio stations that do not require a license
(hereafter "other radio stations") can be in operation.
1.
Before using this terminal, check whether other radio
stations are in operation in your neighborhood.
2. If radio wave interference occurs between the
terminal and "other radio stations", use the
terminal in a different location or "Turn the power
OFF" to avoid the radio wave interference.
3. For details, contact "General Inquiries" on the last
page of this manual.
◆
Wireless LAN (WLAN)
・
Wireless LAN (WLAN) exchanges information using
radio waves, and allows you to freely establish LAN
connection if you are within an area where radio wave
reaches. On the other side, if you communicate without
appropriate security settings, communications may be
intercepted or hacked by malicious parties. It is
recommended to make necessary security settings on
your judgement and responsibility.
・
Wireless LAN
Do not use Wireless LAN in a place where magnetized b y
electric products, AV, OA equipment, etc. or where
electromagnetic wave is generated.
- If magnetism or electrostatic noise affects the terminal,
noise may be increased or communication may not be
available (especially when using microwave oven, it
may affect the terminal).
- Using near TV or radio may cause poor reception or TV
screen may be blurred.
- When multiple wireless LAN access points exist near
the terminal and they use the same channel, search
may not be performed correctly.
・
Frequency bands
Frequency bands used by WLAN devices are as below.
Frequency bands : 2400 MHz band
Modulation : DS-SS method, OFDM method
Expected interference distance : 40 m or shorter
Frequency changing possibility : All bandwidths
between 2400 MHz and 2483.5 MHz are used, and the
bandwidth used by mobile object identification devices
can be avoided.
Available channel varies by countries. To use WLAN
overseas, check the conditions such as available
frequency, regulation, etc. for the country.
To use in airplane, confirm with airline company in
advance.
Cautions on using 2.4 GHz devices
In the bandwidth used by WLAN devices, in addition
to home electric appliances such as a microwave oven
and industrial/scientific/medical devices, in-plant
radio stations for identification of mobile objects used
in production lines of a factory (a license is required),
specified low power radio stations (a license is not
required), or amateur radio stations (a license is
required) can be in operation.
1.
Before using this device, confirm that in-plant radio
stations for identification of mobile objects, specified
low power radio stations or amateur radio stations are
not in operation in your neighborhood.
2. If this device generates harmful radio wave
interference against in-plant radio stations for
identification of mobile objects, change the using
frequency promptly or stop using wireless LAN
function, and contact "General Inquiries" on the last
page of this manual, then consult about treatment
for prevention of the interference (for example,
installation of partitions etc.).
3. If this device generates harmful radio wave
interference against in-plant radio stations for
identification of mobile objects or amateur radio
stations, or if any trouble, contact "General
Inquiries" on the last page of this manual.
14
Contents/Precautions
◆
CAUTION
・
Do not use a remodeled terminal. Using a remodeled
terminal violates the Radio Law.
The terminal is certified according to technical standard
conformance of specified wireless equipment based on
the Radio Law,
If you remodel the terminal by removing its screws, your
certification of technical standard conformance
becomes invalid.
Do not use the terminal with its certification of technical
standard conformance invalid as it violates the Radio
Law.
・
Be careful when you use the terminal while driving a car
etc.
Using a mobile phone while driving is subject to penal
regulations.
However, absolutely necessary cases such as rescue of a
sick person or maintaining public's safety are exempted.
・
Use the Bluetooth function only in Japan.
The Bluetooth function of the terminal is compliant with
wireless standards and is authorized for use only in
Japan.
If you use this function overseas, you may be punished.
・
Use the terminal 15 mm or more away from your body
during communication.
Waterproofness
F-01D provides waterproofness of IPX5*1, IPX7*2 with
firmly closing the external connection jack cap and slot
cap.
*1
IPX5 means that a terminal keeps functioning after applying a
jet flow of 12.5 L/min. from every direction from a distance of
approximately 3 m for at least 3 minutes using water nozzle in
6.3 mm inner diameter.
*2
For F-01D, IPX7 means that a terminal keeps functioning
after F-01D is slowly su bmerged to depth of 1.0 m in static tap
water at room temperature, left there for 30 minutes and then
taken out.
❖
What you can do with waterproofness
of F-01D
・
You can communicate without using an umbrella in the
rain (for rainfall of 20 mm or less per hour).
- When your hands or the terminal is wet, avoid
opening/closing the external connection jack cap or
slot cap.
・
The terminal can be submerged into a pool which has a
depth of 1.0 m.
- Do not operate under water.
- If you put the terminal in water of swimming pool, be
sure to have it within 30 minutes.
- If the terminal gets wet with water from the swimming
pool, wash it in following procedure and drain water in
specified procedure (→P17).
・
You can use the terminal in a bathroom.
- Do not put the terminal in the bathtub. Do not use the
terminal in hot water. May cause malfunction. If you
should drop the terminal into a bath tub, pick it up
immediately and drain water in specified procedure.(
→
P17)
- Never put the terminal in hot spring water or water
containing soap, detergent or bath powder. If the
terminal gets wet with other than tap water, wash it in
following procedure and drain water in specified
procedure (→P17).
- If you use the terminal in a bathroom, use where the
temperature ranges between 5 and 45℃, humidity
ranges between 45 and 99% with limit of not more
than 2 hours.
- A rapid temperature change may cause condensation.
When bringing the terminal from a cold place to a
warm place such as a bat hroom, wait until the terminal
becomes normal temperature.
- Do not apply water flow from a faucet or shower.
・
You can eliminate the dirt by shaking several times in
static water of wash-basin.
- With pr essing and holding the external connection jack
cap and slot cap not to open, wash the terminal
without using a brush or sponge.
15
Contents/Precautions
◆
To ensure waterproofness
To avoid water ingress, be sure to observe the following
points.
・
Do not throw any liquid other than room-temperature
tap water on the terminal, or soak it in such liquid.
・
When attaching/removing docomo mini UIM card or
microSD card, or using the external connection jack, pull
the cap up with your finger by the groove as shown in
the illustration.
Groove
After attaching/removing docomo mini UIM card or
microSD card, using the external connection jack, close
the cap as the direction shown in the illustration, and
make sure that the cap is completely closed without
slack by pushing the tab in.
Tab
Tab
・
Close the connection jack cap and slot cap firmly. Even a
fine obstacle (one hair, one grain of sand, tiny fiber, etc.)
put between contact surfaces may allow water to enter.
・
Do not poke the microphone or speaker with a swab or
sharp object.
・
Do not let the terminal fall. It may become scratched
causing the waterproof performance to degrade.
・
The rubber packings of the connection jack cap and the
slot cap play important roles for keeping waterproof
performance. Do not peel off or damage the rubber
packings. Also, prevent dust from adhering to it.
To keep the terminal waterproofness, replacement of
parts is required every 2 years regardless of whether
the terminal appears normal or abnormal. DOCOMO
replaces the parts as a chargeable service. Bring the
terminal to a sales outlet such as a DOCOMOspecified repair office.
◆
Important precautions
Do not perform actions shown in the illustrations below.
<Example>
Using Soap/Detergent/
Observe the following precautions to use the terminal
properly.
・
Accessories and optional devices are not waterproof.
When playing a moving picture etc. with the terminal
installed in the included desktop holder, do not use it in
a bathroom, shower room, kitchen or lavatory even if it
is not connected to the AC adapter.
・
Do not apply water flow stronger than allowed (→P15)
(e.g., such water flow that gives you pain when applied
to your skin directly from a faucet or shower). F-01D
provides IPX5 waterproof performances. However, it
causes malfunction.
Bath powder
Soaking in
ocean water
Washing with brush/
sponge
Using in hot spring
Machine-washing
16
Applying strong
water flow
Attaching sand/mud
Contents/Precautions
・
Do not put the terminal in hot water, use it in a sauna or
apply hot airflow (from a hair dryer etc.) to it.
・
Do not move the terminal in water or slam the terminal
against the surface of water.
・
If you put the terminal in tap water or in water of
swimming pool, be sure to have it within 30 minutes.
・
When you use the terminal in swimming pool, obey
rules of the facility.
・
The terminal does not float on water.
・
Do not leave water on the terminal. May short-circuit the
power jacks, or in a cold region, water may freeze
causing malfunction.
・
Do not leave water on the microphone or speaker. Such
water may cause failure.
・
If the terminal gets wet with water or other liquids with
the external connection jack cap or slot cover open, the
liquid may get inside the terminal causing electric
shocks or malfunction. Stop using the terminal, turn the
power OFF and contact a DOCOMO-specified repair
office.
・
If the rubber gaskets of the connection jack cap or slot
cap is damaged or deformed, replace it at DOCOMOspecified repair office.
DOCOMO does not guarantee actual operations under
all states. Malfunctions deemed to be caused by
inappropriate operation by the customer are not
covered by the warranty.
◆
Draining water from the terminal
When the terminal is wet, water may flow out after
wiping it off; drain the water in the following steps.
a
Hold the terminal firmly and wipe off moisture on the
terminal surface and back side with dry, clean cloth etc.
b
Shake the terminal approximately 10 times, firmly
holding its longer edge with your both hands with the
display side down, until there is no more water
splattering. Rotate 180 degrees around and shake the
terminal approximately 10 times, until there is no more
water splattering.
17
Contents/Precautions
c
Swing each corner of the terminal in about 10 times
each against dry, clean cloth etc. to wipe off water
remaining in the gaps of outer surface.
d
Swing the terminal in about 10 times against dry, clean
cloth etc. to wipe off water remaining in the
microphone, speaker, keypad, or charging jack, etc.
e
Wipe off water drained from the terminal with dry,
clean cloth etc., and dry naturally.
･
Water, if any, remaining in the terminal may ooze up
after wiping off.
･
Do not wipe off water remaining in gaps directly with
a cotton swab etc.
◆
Charging
Check the following before and after charging.
・
Check if the terminal is not wet when charging. Never try
to charge the battery when the terminal is wet.
・
Accessories and optional devices are not waterproof.
・
When charging the battery when or after the terminal is
wet, adequately drain it and wipe off water with a dry,
clean cloth etc., before connecting the accessory
desktop holder or opening the connection jack cap.
・
When the connection jack cap is opened for charging,
close the cap firmly after charging. It is recommended to
use the desktop holder for charging to prevent water
from seeping inside from the external connection jack.
・
Do not use the AC adapter or desktop holder in a
bathroom, shower room, kitchen, lavatory or other
highly humid area. May cause fire or electric shock.
・
Do not touch the AC adapter or desktop holder with wet
hands. May cause electric shock.
18
Contents/Precautions
Before using the terminal
Part names and functions
a
b
c
d
e
f
a
b
j
k
l
<Functions>
a
Indicator light
Light in red : Charging
*
Lighting color depends on application.
b
Microphone
c
In-camera
g
h
i
f
d
Light sensor
Sense ambient brightness and automatically adjust
brightness of the display backlight (may not be
adjusted correctly, if covered).
e
Display (Touch panel)
f
Speaker
g
1Seg antenna
*
The antenna is built in the terminal. Covering around the
antenna by the hand may affect the quality.
h
Bluetooth/Wi-Fi antenna
*
The antenna is built in the terminal. Covering around the
antenna by the hand may affect the quality.
i
GPS antenna
*
The antenna is built in the terminal. Covering around the
antenna by the hand may affect the quality.
j
Out-camera
k
Xi antenna
*
The antenna is built in the terminal. Covering around the
antenna by the hand may affect the quality.
l
Charging jack
m
Earphone/Microphone jack (waterproof)
n
External connection jack
Connect the included USB Cable for PC connection T01
or FOMA charging microUSB adapter T01 (optional).
m
*
n
o
p
Insert the microUSB plug with facing printed side up into the
external connection jack horizontally.
o
microSD card slot→P21
p
docomo mini UIM card slot→P20
<Key functions>
Key functions are as follows.
a
Volume button
Press : Adjust volume.
b
Power key
Press : Activate/Deactivate the sleep mode.
Press and hold : Turn the terminal ON/OFF.
ty
X
19
Before using the terminal
docomo mini UIM card
The docomo mini UIM card is an IC card that stores user
information.
･
A docomo mini UIM card is only available for the
compatible terminal. If you replace your UIM with a
docomo mini UIM card, part of websites or data used
previously may not be available.
･
A docomo mini UIM card is only available for the
terminal. If you have a UIM or FOMA card, bring it to
docomo Shop to replace.
･
If the docomo mini UIM card is not attached, you cannot
use some functions of the terminal.
･
For details on docomo mini UIM card, refer to the
docomo mini UIM card manual.
◆
Attaching/Removing docomo mini
UIM card
･
Attach/Remove the docomo mini UIM card after turning
OFF the power.
■
Attaching
Open the slot cap of the terminal (a), align the docomo
mini UIM card with the UIM card mark on the back side of
the terminal, then insert the docomo mini UIM card with
the IC side up in the direction of b all the way until it clicks.
･
Check the orientation of UIM corner cut.
a
Corner cut
b
IC
docomo mini UIM card
■
Removing
Open the slot cap of the terminal (a), press the docomo
mini UIM card lightly toward b, pull out straight the
popped out docomo mini UIM card in the direction of c.
a
b
✔
INFORMATION
･
When handling docomo mini UIM card, take care not to
touch or scratch the IC part. Note that attaching or
removing docomo mini UIM card forcibly into the
terminal may damage docomo mini UIM card.
･
Note that the docomo mini UIM card may pop out of the
terminal when removing it.
◆
Security codes of docomo mini UIM
c
card
A docomo mini UIM card has a security code named PIN
code. The PIN code is set to "0000" by default, which you
can change by yourself.→P43
20
Before using the terminal
microSD card
◆
microSD card
Attach microSD card or microSDHC card in the terminal
before use.
･
The terminal supports microSD card of up to 2 Gbytes,
and microSDHC card of up to 32 Gbytes (as of October,
2011). Note that DOCOMO does not guarantee actual
operations of all microSD cards and microSDHC cards.
･
Do not turn the power OFF or give shock while accessing
data on the microSD card. The data may corrupt.
◆
Attaching/Removing microSD card
･
Unmount or turn the power off before attaching/
removing a microSD card.
■
Attaching
Open the slot cap of the terminal (a), align the microSD
card with the microSD card mark on the back side of the
terminal, then insert the microSD card with the IC side up
in the direction of b all the way until it clicks.
a
bb
■
Removing
Open the slot cap of the terminal (a), press the microSD
card lightly toward b, pull out straight the popped out
microSD card in the direction of c.
a
bb
✔
INFORMATION
･
Note that the microSD card may pop out of the terminal
when removing it.
c
Charging
❖
Precautions on charging
･
If you use the terminal while charging, it may take time
to complete charging or charging may not complete.
･
It is normal for the terminal or AC adapter to become
warm while charging. When the terminal becomes
warm, charging may stop temporarily for the safety.
When the terminal becomes extremely hot, stop using
immediately.
･
The following conditions will lead to a charging error. In
the case of charging error, running functions are
stopped, the power is turned off, and the indicator light
turns off. Remove the charger.
- Charging voltage is high
- The internal battery is over-charged/over-discharged
- Charging is not complete after 10 hours or more
- The battery temperature becomes out of guaranteed
operating range.
21
Before using the terminal
❖
Charging times (approximate)
The following is the time for charging an empty internal
battery with F-01D's power switched OFF. Charging with
the terminal ON or under low temperature requires longer
time.
AC adapter
DC adapter
❖
Operation time on full charge
AC Adapter F05 : Approx. 400 min.
AC Adapter 01/02 : Approx. 950 min.
Approx. 860 min.
(approximate)
The following time varies by the charging method and
operating environment.→P109
Continuous
stand-by
time
❖
･
･
❖
For details, refer to the operation manual of AC adapter or
DC adapter.
AC Adapter F05 (Accessory)*1 :
FOMA AC Adapter 01 (optional)*2 :
FOMA AC Adapter 02/FOMA AC Adapter 01 for Global use
FOMA/3GStationary (Auto) : Approx. 1,600 H
GSM
Stationary (Auto) : Approx. 1,200 H
LTE
Stationary (Auto) : Approx. 900 H
Internal battery life
The internal battery is a consumable part. Each time it is
charged, time available with each charging reduces.
When a time available with each charging is reduced to
about a half from that of a new battery, replacement of
the internal battery is recommended because it is near
the end of life. For replacement of the internal battery,
contact "Repairs" on the last page of the instruction
manual (in Japanese only) or a DOCOMO-specified
repair office.
Available charging adapter
Applicable to 100-240V AC.
100V AC only
*1, 2
(optional)
:
Applicable to 100-240V AC.
FOMA DC Adapter 01/02 (optional)*2 :
a car.
*1
The shape of the AC adapter plug is for 100V AC (national
specification). When using the AC adapter applicable 100240V AC overseas, use the adapter plug that is suitable for use
in your travel destination. Do not charge the battery using a
transformer for overseas travel.
*2
Can be used in combination with FOMA charging microUSB
adapter T01.
❖
Checking battery level
A battery icon is displayed on the status bar to show
estimated battery level.→P27
You can check estimated battery level in percent figures in
the following steps.
･
Tap the battery level icon area from the clock on the
status bar
･
From the Applications menu, [Settings]→[About phone]
→
[Status]
✔
INFORMATION
･
When charging starts with the battery empty, the
terminal may not be immediately activated after turning
the power ON. In this case, charge the terminal while
keeping it turned OFF, and turn it on after a while.
◆
Setting for desktop holder charging
When charging with the included desktop holder F35,
make sure the setting before charging.
･
For charging without the desktop holder, changing the
setting is not needed.
From the Applications menu, [Settings]
1
[Initial setting]→[Charge DeskTop Holder
Setting]
→
Quick charge :
Regular charge :
Select charging method
AC adapter F05.
the included AC adapter F05.
Select when charging with the included
Select when charging with other than
Use for charging in
→
22
Before using the terminal
◆
Charging with Desktop holder
Use the included AC adapter F05 and Desktop Holder F35
to charge.
a
Connect the power cable side of the AC adapter and
USB cable
b
Insert the microUSB plug of the AC adapter with facing
the "B" printed side up into the jack on the back side of
the desktop holder
c
Insert the AC adapter power plug into a 100V AC outlet
d
Insert the terminal into the desktop holder
･
Make sure that the indicator light lights in red. The
indicator light turns off when charging ends.
e
When charging is complete, remove the terminal from
the desktop holder
f
Remove the AC adapter power plug from the wall outlet
and microUSB plug of the AC adapter from the desktop
holder
Light
To AC 100V
outlet
AC Adapter F05
Power plug
◆
Charging with AC adapter
You can charge with included AC adapter F05.
a
Connect the power cable side of the AC adapter and
USB cable
b
Open the jack cap (a) of the terminal, insert the
microUSB plug of the AC adapter with facing the "B"
printed side up into the external connection jack (b)
c
Insert the AC adapter power plug into an outlet
･
Make sure that the indicator light lights in red. The
indicator light turns off when charging ends.
d
Remove the AC adapter power plug from the wall outlet
and microUSB plug of the AC adapter from the external
connection jack
Jack cap
External connection
jack
Light
microUSB
plug
To AC 100V
outlet
USB cable
Desktop
holder
USB cable
Power cable
Jack on the back side
of desktop holder
microUSB plug
AC Adapter F05
23
Power plug
Power cable
Before using the terminal
◆
Charging with USB Cable for PC
connection
Connect the terminal to a PC inserting the included USB
Cable for PC connection T01 into the external connection
jack of the terminal to charge the terminal via the PC.
･
When "
新しいハードウェアの検索ウィザードの開始
hardware detection wizard)" appears on the PC, select "
キャンセル
･
(Cancel)".
If charging via the external connection jack and charging
with the desktop holder are attempted at the same time,
charging with the desktop holder is given priority.
(New
Power ON/OFF
◆
Turning power ON
X
1
■
･
･
･
◆
1
(2 sec. or more)
The terminal activates with the screen locked. [None]
is set by default.
･
Setting/Canceling screen lock→P44
Turning power ON for the first time
Follow the onscreen instructions to set up. The setting
can be changed later.
- Setting language→P63
- Setting location information service→P87
- Setting a Google account→P27
When a confirmation screen for software update
function appear, tap [OK].
If the terminal is initialized, the terminal operates in the
same way as the first activation.
Turning power OFF
Press down
confirmation screen appears
･
Press and hold X for 10 seconds or more to
turn off the power forcibly.
X
until the shutdown
→
[Shut Down]
Basic operation (Using touch panel)
The display of the terminal is a touch panel which you can
operate by directly touching with your finger. A motion
sensor detects the orientation and movement of the
terminal so that the screen switches depending on if the
terminal is held vertically or horizontally.
◆
Notes for using the touch panel
The touch panel is designed for being touched lightly with
fingers. Do not push it forcibly with a finger or press it with
sharp objects (nail, ballpoint pen, pin, etc.).
･
Touching the touch panel may not work in the following
cases. Note that it may cause malfunction.
- Operation with gloved hands
- Operation with tip of fingernail
- Operation with a foreign object on the display
- Operation with protective sheet or seal on the display
- Operation on the wet touch panel
- Operation with finger wet with perspiration or water
◆
Main operations
❖
Tap/Double-tap
Tap :
Touch the screen lightly and release. The operation
becomes effective when you release your finger from
the screen.
Double-tap :
Tap twice quickly.
Examp le : Tap
24
Before using the terminal
❖
Touch and hold for 1 second or more
Touch and hold the screen for 1 second or more and
release. You may need to perform the subsequent action
with your finger kept touching the screen.
*
In this manual, the operation may be described as "(1 sec. or
more)".
❖
Drag/Slide/Pan
Drag :
Touch an item or icon on the screen and move it to
the desired position.
Slide :
Touch the screen and crisscross.
Pan :
Drag the screen in any direction to view the desired
part.
❖
Flick
Touch the screen and flick away.
◆
Switching between landscape and
portrait view
You can switch between landscape and portrait view by
turning the terminal sideways/upright (auto-rotation).
･
Mark [Auto-rotate screen] to activate.→P58
･
Even when you change the orientation of the terminal,
the screen may not change depending on the screen
displayed.
Examp le : Dra g
❖
Pinch
Touch the screen with two fingers and widen (pinch-out)
or narrow (pinch-in) the fingers' distance.
Hand gesture control
Hand gesture control is a function with which you can
operate the terminal just by shaking your hand in front of
the in-camera, instead of touching the touch panel. From
the position a little away from the terminal or with a wet
hand, you can operate the touch panel.
･
While the function is active, since the display is kept
lighting to maintain a state in which the in-camera
detects hand motion, the battery consumption becomes
faster.
25
Before using the terminal
❖
Notes for using the hand gesture
control
･
When using the hand gesture control, put the terminal in
the desktop holder for example to keep it immobile.
･
To help detect hand motion correctly, note the followings.
- Place your hand approximately 40 - 60 cm away from
the in-camera and at approximately 15 degrees up or
down, approximately 20 degrees left or right from the
center of the in-camera.
- Wave your hand from right to left or up and down at
the in-camera.
In-camera
Example : Shaking hand left and right
In-camera
Example : Shaking hand up and down
- When a hand gesture control is performed, the
direction in which the hand gesture control is received
is indicated with a mark. While a mark is indicated,
hand gesture control made from directions other than
the marked direction is invalid. Operate after the mark
disappears.
- Either the left or right hand can be used, but if the both
hands are used at the same time, the terminal cannot
be detected.
- Operating with a gloved hand may not be detected
correctly.
- Depending on the circumstances (brightness of the
room, cloths, background, light source, etc.), hand
motions may not be correctly detected.
･
Depending on the way to wave the hand, hand gesture
may not be detected correctly.
･
Big actions near the camera may detect by mistake.
･
Activating the function disables [Auto-rotate screen](
P58) setting and auto-rotation does not work. Place the
terminal in the orientation with the in-camera at the top
of the display. After finishing the function, auto-rotation
remains disable. Mark [Auto-rotate screen] to use autorotation
･
The function cannot be used while camera/video
shooting. The function ends when the camera activates.
･
To use data interchange with DLNA compatible devices,
connect the player to the server.
❖
Available main functions and
operations
Shaking your hand performs the following operations.
･
Some other functions may be operated in the same way.
■
Browser
Up/Down/Left/Right : Scroll through the display up/down/
left/right
■
1Seg
Up/Down : Adjust volume
Left/Right : Switch channels
■
DLNA
Up/Down : Adjust volume
Left/Right : Skip a moving picture
■
Gallery
Left/Right : While displaying image, switch to the next/
previous image
26
Before using the terminal
→
◆
Using hand gesture control
You need to activate the hand gesture control and an
application at the same time.
･
Either before or after the application is activated, the
hand gesture control can be activated.
Tap the clock on the status bar
1
ON/OFF the hand gesture control
Turning ON the hand gesture control displays on
the status bar.
Using the hand gesture control in an
2
application
･
Turning the screen off turns the hand gesture
control off.
→→
Turn
❖
About other initial settings
Set the following items as required in addition to the initial
setting items.
･
Email account settings→P69
･
Wi-Fi functions settings→P51
･
Access point (APN) settings→P50
･
Switching to English display→P63
Screen/Icon
◆
Icons on the status bar
Various conditions can be checked with notification icons
and status icons appearing on the status bar.
Initial setting
You can set necessary items collectively for the first time
to use the terminal.
･
Each setting can be changed anytime.
From the Applications menu, [Settings]
1
[Initial setting]
Set each item
2
Lock screen :
HOME wallpaper :
Photo Screen :
Phonebook copy :
Google Accounts :
Charge DeskTop Holder Setting:
Set screen lock.→P44
→
P30
charging with the desktop holder.→P22
Set wallpaper on the Home screen.
Set an image for lock screen.
Copy phonebook.→P49
Set Google Account.
Set the manner of
→
Notification icon
■
Main notification icons
: New Gmail message
: New Email message
: New SMS message
: Area Mail
: Sending SMS is failed
: New instant message
: High-performance unified search update
: Notifying calendar
：
During alarm snooze
*1
: Music player is activated
: Wi-Fi is on, and Wi-Fi network is available.
: Wi-Fi tethering is enabled.
: USB is connected.
: USB tethering is enabled.
: Wi-Fi tethering and USB tethering are enabled.
: File received via Bluetooth
: Uploading data is completed.
: Downloading dada is completed.
27
Before using the terminal
Status icon
: Installing applications from Android Market etc. is
completed.
: Earphone is connected (using terminal microphone).
: Earphone is connected (using earphone microphone).
: Receiving 1Seg radio wave
: Recording 1Seg program
： Notification icon (software update available)
： Notification icon (software update completed)
: Positioning with GPS
: VPN is connected
: VPN is not connected
■
Main status icons
*2
: Signal strength
*2
: During International roaming
: Out of service area
: GPRS is connected.
: Connecting 3G (packet)
: LTE is connected.
: Airplane mode
*2
: Wi-Fi is connected.
: Bluetooth function is ON.
: Charging is needed.
: Battery level is low.
: Battery level is enough.
: Charging
: Manner mode
: Manner (silent)
: Manner mode (alarm)
: Personalized manner mode
: Hand gesture control ON
*1
Displays when it is active in background.
*2
Displays in blue when logging in with a Google account.
◆
Notification panel
Tap the clock on the status bar to display the notification
panel. On the notification panel, you can check the
terminal status by icons and check notifications of
messages or schedules.
Tap the clock on the status bar
1
Status of the terminal
Setting panel display
button
Notification panel
･
Tap each notification to check the detailed or make
necessary settings.
･
If [×] is displayed on the notification, tap [×] to delete
the notification.
･
Setting panel →P28
･
Tap an area other than the notification panel to close the
notification panel.
◆
Setting panel
On the setting panel, you can make settings for Wi-Fi/
Bluetooth/GPS function, etc. or view the setting menu.
Tap the clock on the status bar
1
28
→
Notification panel
display button
Setting panel
Before using the terminal
Make settings or tap [Settings] to display
2
the setting menu
･
Setting menu→P50
･
Tap an area other than the setting panel to close the
setting panel.
◆
When the screen display is turned
off
When no operation is performed in certain period of time,
the display is automatically turned off according to the
screen time out setting and the terminal goes into sleep
mode.
X
1
The sleep mode is canceled.
･
When screen lock is activated, screen lock is
deactivated.→P45
✔
INFORMATION
･
When activating sleep mode manually, press X
while in display mode.
Home screen
Home screen is a start screen to use applications. You can
return to the Home screen anytime by pressing .
You can customize the home screen by locating
applications or widgets. Up to 5 home screens can be set.
You can switch the screens by sliding left and right.
◆
Viewing home screen
a
d
e
fgh
a
Google Search/Voice Search→P62
b
Display the Applications menu→P30
c
Display the customizing screen for the Home screen
P30
d
Customize area
e
Number of the home screens lying on the left and right
f
Return to the previous screen
g
Display the Home screen
h
Display the recently used application window→P33
i
Status bar→P27
b
c
e
i
→
29
Before using the terminal
◆
Customizing the Home screen
You can locate desired application shortcuts or widgets on
the Home screen or change wallpaper. You can also
change color theme or style of the screen.
❖
Adding shortcuts or widgets
From the Home screen,
1
[Widgets]/[Apps]/[More]→Drag an item to
2
the screen you want to add to
You can paste a selected item on the Home screen.
･
You can drag pasted items to change their
positions.
✔
INFORMATION
･
Even though 2 or more widgets for speed addresses are
pasted, up to 4 items can be registered. All widgets for
speed addresses are linked and their contents become
the same.
❖
Deleting shortcuts or widgets
From the Home screen, slide left and right
1
to display the Home screen that you want to
customize
Select a shortcut or widget you want to
2
delete (1 sec. or mode)
drag it to
icon turns red
❖
Changing Home screen wallpaper
From the Home screen,
1
[Wallpapers]→[Gallery]/[Live Wallpapers]/
2
[Wallpapers]
･
When you select an image by tapping [Gallery],
drag the inside of the trimming frame to specify the
→
→
Keep touching to
→
Lift your finger when the
Select an image
position, and drag the corner of the trimming frame
to zoom in/out, and tap [OK] before setting is
complete.
･
When you select an image by tapping [Live
wallpapers], tap [Set wallpaper] to set the image as
a wallpaper. For some images, tap [Settings] to
make advanced settings.
❖
Customizing color theme or style
From the Home screen,
1
[Style]→[Change color theme]/[Change
2
style]
→
Select an item
･
When [Change style] is tapped, you can tap [＋
Create] to create, set a style.
･
To delete a style, touch and hold a style for 1 second
or more on the style selection screen, keep touching
to drag it to and lift your finger when the
icon turns red, then tap [Yes].
Applications screen
Display the application menu so that you can activate
registered applications or change the terminal settings.
･
For some applications, "Compatibility zoom"
confirmation screen may appear when activating. Tap
[OK] to fit the application to the display size of the
terminal and the confirmation screen does not appear
from the next activation. Tap on the status bar to
change the display size.
◆
Displaying Applications menu
From the Home screen,
1
The applications menu appears.
Sort and display : [Sort]→[By name]/[By download
date]/[By frequency of use]/[By organize]
Switch pages : Slide from side to side
30
Before using the terminal
◆
Main applications
･
Some applications require subscriptions (charged
service).
BeeTV :
BeeTV is a broadcasting station dedicated for
mobile phones. You can watch programs such as
original dramas, music or varieties.
BOOK☆WALKER :
application with full of books such as light novels,
comics, literary works, library books issued from
KADOKAWA group. You can also enjoy electronic
version limited works or free samples.
BOOK
ストア
Store 2DFacto is an e-book store where you can view
and buy e-books in many categories such as serious
novels, popular comics, hot business books, etc.
eco
モード
consumption. It can be automatically enabled according
to the battery level. You can easily change the setting
from the widget.
Evernote :
various information such as website contents, shot
images, idea memos to the server to search/view at any
time you want it. Saving or viewing information can be
available not only from the terminal but also PC or other
devices.
*
To use the application, create an Evernote account is required.
Fanplus :
contents of entertainment group such as Takarazuka, DBOYS, animation, gravia idols, sports group such as
football, tennis, female professional golf or culture
group such as trains, history, Japanese sit-down
comedy.
Gmail :
Google Search :
website.
G
ガイド番組表
based broadcasting, BS digital broadcasting. Program
search by keywords or categories and remote recording
from outside are available.
Hulu :
Enjoy popular Hollywood movies or foreign
dramas at a fixed rate.
It is a store/viewer all-in-one e-book
2Dfacto (BOOK Store 2DFacto) :
(eco mode) :
Evernote is a service that allows you to save
"Fanplus" is a fan site with different kind
Send/Receive Google account mails.→P71
eco mode reduces battery
Search functions in the terminal or
(G-GUIDE program table) :
BOOK
View ground-
JOOKEY :
You can watch information variety programs
featuring famous people from Yoshimoto showmen and
specialists.
Latitude :
You and your friends can check where you
are on the map.→P88
Mobage :
Enjoy Mobage contents with this application.
My docomo
information such as your usage charge or docomo point
with this application.
Pulse :
RSS or news website information in thumbnail. You can
view any information shortly with intuitive operations.
Qik Video :
communication such as social video sharing/video chat/
video mail/video archives simply with one application.
sp
using DOCOMO's mail address (@docomo.ne.jp).
Pictograms and deco-mail can be used, and automatic
reception is also supported.→P67
Twitter :
You can communicate with someone by posting a short
message on a website.
Twonky Special :
in the smartphone or published on the website can be
played back wirelessly on the DLNA compatible TV or
audio device.
*
To use contents on the website, an access point connectable to the
Internet is required.
VirusScan (docomo Anshin Scan) :
from virus damage. The application detects virus hidden
in installed applications or microSD card.
YouTube :
Area Mail :
and viewed with this application.→P72
Camera :
Calendar :
Gallery :
with the camera or downloaded from website and saved
in a microSD card.→P81
31
アプリ
(My docomo app) :
This news reader application can display each
You can enjoy integrated video
モードメール
(sp-mode mail) :
This is an official client application of Twitter.
Videos, still images or music stored
You can watch YouTube video.→P83
Early warning "Area Mail" can be received
Shoot pictures or videos.→P79
View calendar and register schedule.→P95
View still images or moving pictures taken
Check
Send/Receive emails
Protect the terminal
Before using the terminal
ジークラウド
environment provided NHN Japan.
Downloads :
website.
Talk :
docomo market :
can search applications and videos.→P86
ドコモ海外利用
application supports packet communication usage
overseas. You can set data roaming settings or network
operators for overseas Pake-hodai simply.
Navigation :
Google Maps Navigation.
Browser :
Places :
information around where you are.→P89
Market :
Maps :
and calculate routes.
Email :
Messaging :
Music :
Sound recorder :
Voice Search :
sound.
terminal. You can activate desired functions from
instructions.
*
See "About manuals for F-01D" in "Introduction".
書籍・コミック E★エブリスタ
EVERYSTAR) :
electronic comics ranged from original works by
professional authors/famous people to general user
posted popular works.
Settings :
地図アプリ
with functions such as 地図 (map),
facilities search), ナビ (navigation), 乗換 (transfer) or
た街
Calculator :
subtraction, multiplication, and division.→P96
(GCLOUD) :
Manage images, etc. downloaded from
Chat via Google Talk.→P73
Search routes toward destinations using
View web pages like a PC.→P73
Use Google places to search detailed
Use Android Market.→P84
View your current location, find other locations
Send/receive emails to/from users of PC.→P69
Send/receive SMS.→P67
Play music files.→P81
Clock :
Display a clock or set alarm.→P95
Instruction Manual :
Make the terminal settings.
(Map Application) :
(visited town).
Perform calculations such as addition,
Enjoy games in cloud
Access docomo market where you
(International roaming) :
Record voice.
Search information in website by voice
The instruction manual for the
View high-profile electronic books and
(Books, comics E
Support your outing
お店や施設検索
The
★
(shop/
訪れ
PhoneBookCopy :
external recording medium with this application.
楽天オークション
Rakuten auction.
Contacts :
so that you can address someone from contacts by
simple operation.→P47
◆
Other applications
＠F
ケータイ応援団
Connect to ＠F
Adobe Reader :
Backup :
bookmarks, images, moving pictures, music, system
settings to or from a microSD card or the cloud.
BooksV :
FUJITSU to use the website where you can buy books,
magazines, contents including static or reports useful
for business scenes.
DiXiM Player :
terminal.→P93
DiXiM Server :
card on the terminal to a DLNA device.→P93
Document Viewer :
etc.→P97
F media2U :
music or moving pictures.
F-LINK :
or receive still image files or moving picture files to or
from F-LINK compatible devices.
GREE :
which over 25 million users enjoy communications or
games.
HOT PEPPER HD :
service with full of latest search technology so that you
can easily search store information. You can also search
beneficial coupons.
32
Move or copy phonebook data using
(Rakuten auction)：Auction or bid at
Register phone numbers or email addresses
(@ F mobile phone supporters) :
ケータイ応援団
View a PDF file.
Back up/Restore phonebook entries, SMS,
BooksV is an application provided by
Play contents in a DLNA device on the
Deliver images stored in the microSD
An media player application for playing
Using the Wi-Fi function, you can easily send
This is an official application of GREE, with
site.
You can view Microsoft office files,
This is a search application for food
Before using the terminal
KSfilemanager :
application
Nissen_downloader :
focusing on women's fashion, including underclothing,
shoes, bags, furniture, beauty products, etc. by a finger.
TSUTAYA TV :
various genres of images such as movies, animations,
etc. at any time.
High-performance unified search:
search directly in a specified search engine such as
shopping or foodie.→P63
サロン検索
Internet reservation sites in Japan, full of beauty
information and aesthetic information such as hair
salons, relaxation, manipulative treatment, chiropractic,
nail salons, healing salons (hot bath, oxygen treatment,
etc.), eye makeup, etc.
じゃらん
information site "
CO., LTD. with which you can search more than 20
thousand hotels or "
Schedule St. HD:
TODO, text, photo, voice memo functions, to which you
can easily add features or designs.
Change style :
すまふぉ
you to view the lineup of multi-channel broadcasting
service provided by Hikari TV easily.
Task manager :
TV :
Password manager :
information such as ID and password, quote the
registered information.→P41
Homescreen selector :
application.
ポンパレ
今日何つくる？楽天レシピ
recipe for tablets) :
the official application of Rakuten recipe.
e-Dictionaries+ :
renowned dictionaries in Japan to respond to every
scene in daily study/business.→P96
A high-functional file managing
You can buy various items
A service with which you can enjoy
(HOTPEPPER beauty) :
(Jaran) :
This is an application for the travel
じゃらん
net" produced by RECRUIT
宿泊プラン
A schedule application containing
Change style of display.
DL (Hikari TV) :
Watch 1Seg.→P89
(Pomparade) :
An application which allows
Display running applications to quit.
Register authentication
Switch Home screen
Use Group Buy tickets.
for
A recipe site produced by Rakuten,
Dictionary software unifying most-
Enter a keyword and
One of the largest
(stay plan)".
タブレット
(Rakuten
◆
Opening the recently used
application window
→
Select an application you want to
1
activate
Character Entry
Enter characters using the software keyboard displayed
on the screen.
･
Character entry using NX!input powered by ATOK is
mainly explained here.
◆
Using the keyboard
You can enter characters using numeric keyboard,
QWERTY keyboard, handwritten keyboard or Japanese
syllabary keyboard.
･
You can activate voice input from each keyboard.→P37
■
Numeric keyboard
4 types of input methods can be used : Numeric keypad
input, Gesture input, Gesture input pro, Flick input.→P36
a
b
g
d
e f
33
Before using the terminal
c
■
QWERTY keyboard
Enter characters using Romaji input.
a
c
b
d
e f
■
Handwriting keyboard
Enter characters in handwriting.
a
g
d
e f
■
Japanese syllabary keyboard
Enter Japanese syllabary or alphabetical order.
a
b
d
e f
b
d
e f
Alphanumeric input mode
a
Word suggestions display area : Show to select word
suggestions when entering characters
･
Slide display area of word suggestions to show
hidden suggestions. On some keyboards, text before
c
b
c
c
c
c
fixed is displayed under suggestions.
･
Word suggestions may not be displayed depending
on the text input field.
b
: Restore the latest fixed text to the original
: For the numeric keyboard input, display characters
assigned to the key in the reverse order
: Move the cursor to the left
/ : Move the cursor up/down
/ / : Switch input mode (kana, alphabet,
numeric)/(kana, alphabet)/(kana, alphanumeric)
･
Touch and hold for 1 second or more to make ATOK
setting or register words from the NX!input menu.
/ : Switch hiragana/katakana
: Switch between uppercase and lowercase
characters in the alphabet input mode
･
On the Japanese syllabary keyboard, each time you
tap, entry mode changes to uppercase character
uppercase mode→lowercase character.
･
Alternatively, flicking up each key to enter uppercase
character.
: Set/Cancel uppercase mode
: Switch to number and symbol input mode
･
Alternatively, flicking down each key to enter number
or symbol allocated to the key.
: Switch between input of pictograms, smileys,
symbols, common phrases, character codes and
quote input using Password manager or Contacts.
･
With the key, you can show/hide the keyboard.
: Select from "
kana/two-byte katakana/one-byte katakana, alphabet
: Convert into katakana/numeric/alphanumeric/date
(two-byte/one-byte)
後変換
(Post-convert)" suggestions for
→
34
Before using the terminal
c
/ : Delete a character immediately to the left of the
cursor.
: Move the cursor to the right
/ : Switch between lowercase, voiced sound
mark, semi-voiced sound mark and uppercase
characters in the alphabet input mode
･
The current settings are indicated in light blue.
/ : Switch between two-byte character and on-
byte character
･
The current settings are indicated in light blue.
/ : Convert character/Enter a space
/ : Move the cursor to the next entry item/Fix or
insert line feeds
･
Besides, depending on the situation, some keys such
as , , may have other functional roles.
/ : Move to the left or right display frame on
the handwriting keyboard.
d
e
f
g
/ / / : Switch the
keyboard
/ / / : Enter
smileys/symbols/common phrases (except for when
entering sp-mode mail)/pictograms (When entering
sp-mode mail)
: Activate voice input
: Touch and hold for 1 second or more to
switch display position of the numeric keyboard.
･
Alternatively, dragging with two fingers in the
direction you want to move on the numeric keyboard
switches the position.
: Touch and hold for 1 second or more to
switch between divided display and normal display
of the QWERTY keyboard.
･
Alternatively, pinching in/out on the QWERTY
keyboard switches the keyboard display.
: Touch and hold for 1 second or more to
switch number of input boxes on the handwriting
keyboard.
: Hide the keyboard
: Make settings for the keyboard
Handwriting area : Enter characters writing with your
finger
･
Tap unfixed characters to display word suggestions.
Tap the character to change the character.
･
If you write character in a rightmost input box, the
input box automatically scrolls to move to the
extreme left.
･
When the QWERTY keyboard is divided, the
handwriting area is displayed in the center.
･
Slide to show more space.
❖
Displaying/Hiding the keyboard
■
Displaying the keyboard
Select the text input field
1
■
Hiding the keyboard
While displaying the keyboard,
1
･
Alternatively, you can tap to display the guide. To
hide the keyboard, slide the guide to the direction
you like and after is switched to , slide to
again and release your finger.
35
Before using the terminal
❖
Numeric keyboard input mode
You can use following 4 modes on the numeric keyboard.
･
Select input mode from the setting menu of Software
keyboard.→P38
■
Numeric keypad input
Tap continuously a key assigned the character you want to
enter until the desired character is displayed.
■
Gesture input
If you tap and keep your finger on the key assigned the
character you want to enter, characters (gesture guide) will
be displayed around that key. Slide your finger to the
desired character without removing your finger from the
screen.
･
To enter voiced/semi-voiced sound or small characters,
slide once or twice downwards without releasing your
finger from the key. A gesture guide for voiced/semivoiced sound or small characters will be displayed
around that key. Slide your finger to the desired
character without releasing your finger from the screen.
Slide
downward
twice
･
In the alphanumeric input mode, you can switch
between uppercase and lowercase characters by sliding
downwards without releasing your finger from the
screen.
■
Gesture input pro
You can make settings for displaying/hiding the gesture
guide or how long it takes until the gesture guide appears.
･
For setting procedure, see [Software keyboard setting].
→
P38
Example: Entering ぱ
■
Flick input
If you touch and keep on the key assigned the character
you want to enter, characters (flick guide) will be displayed
on that key. Flick towards the desired character without
releasing your finger from the screen.
･
To enter voiced/semi-voiced sound or small characters,
tap once or twice after flicking.
◆
Convenient input functions
You can enter pictograms, symbols or common phrases,
or quote contacts data.
❖
Entering by the pictogram/smiley/
symbol palette
･
Pictograms can be entered when creating an sp-mode
mail.
→
1
2
(pictogram)/ (smiley)/
(symbol)
･
When / / is displayed
on the keyboard, tap to operate in the same way.
Select the category →Select a pictogram/
smiley/symbol you want to enter from the
item list
･
You can display categories not on screen by
scrolling the category field at the top of the palette
to the left and right.
･
You can display items not on screen by scrolling the
list to the left and right.
･
You can display the history list beginning with the
newest entered item by tapping [履歴 (History)] at
the top left of the palette. You can also enter items
from this history list.
36
Before using the terminal
❖
Entering common phrases
→
1
･
When is displayed on the keyboard, tap it
to operate in the same way.
Category
Select a category→Select a common phrase
2
you want to enter from the list
❖
Entering from the character code
table
→
1
Select a category→Select a character you
2
want to enter from the list
❖
Entering quoting from contacts
→
1
[
電話帳／
2
direct input)]
contacts list
Category
ATOK
ダイレクト
→
Select a name in the
→
Mark item to quote→[OK]
(Contacts/ATOK
❖
Entering by voice input
You can enter characters by converting your voice.
･
When the terminal is not connected to the network, you
cannot use the voice input.
When entering characters,
1
the word you want to enter
Select a character from the search
2
suggestion list
･
If the spoken word is not recognized properly, tap [Redo]
to speak again.
･
You can display candidates not on screen by scrolling
the recognition candidate list up and down.
◆
Switching to the Android keyboard
You can enter characters switching to the Android
keyboard.
･
The Android keyboard does not support the Japanese
input mode.
From the Applications menu, [Settings]
1
[Language & input]→[Current input
method]
Select a type of the Android keyboard
2
✔
INFORMATION
･
To return to the ATOK keyboard, select [NX!input] in Step
2.
→
Speak
→
37
Before using the terminal
◆
Setting ATOK
❖
Software keyboard setting
From the Applications menu, [Settings]
1
[Language & input]→[Configure input
methods]
→
[Settings] under "NX!input"
[Software keyboard]
Set each item
2
Keypad sound :
operation tone sounds each time you tap a key.
Keypad vibration :
terminal vibrates each time you tap a key.
Input mode*1 :
keyboard.
Multi-tap input*1 :
excluding numeric keypad input] is marked, Multi-
tap input is available when using gesture input or
flick input. When the "Enable auto cursor moving" is
marked and if you take a certain amount of time
before tapping the same key again, the cursor
automatically moves to the right and stands by for
the next character entry. You can also set the time
(tap interval) before the cursor moves.
Character delete key*1 :
character immediately to the left of the cursor is
deleted when is tapped. When [CLR] is selected,
the character immediately to the right of the cursor
is deleted when is tapped.
Gesture guide*1 :
and if "Show the gesture guide" is unmarked and
[OK] is tapped, the gesture guide is no longer
displayed. When this checkbox is marked, you can
set the time before the gesture guide is displayed
after a key is tapped.
Flick guide *1 :
the flick guide.
When this checkbox is marked, the
When this checkbox is marked, the
Set the input mode for the numeric
When the [Enable multi-tap input
When [BS] is selected, the
When setting to gesture input Pro
In the flick input mode, mark to display
Flick Sensitivity*1 :
adjust the sensitivity of flick input.
Auto alphanumeric select*2 :
marked, input mode is one-byte alphanumerics
→
→
when switched from the numeric keyboard to the
QWERTY keyboard.
Direct alphanumeric input *2 :
marked, entered alphanumerics are fixed one by
one.
Auto space insert*2 :
automatically after a word is applied in the
alphanumeric input mode.
Show numeric keys (vertical screen)*2 :
checkbox is marked, the numeric key is displayed
when the QWERTY keyboard is displayed vertical.
Show numeric keys (horizontal screen)*2 :
checkbox is marked, the numeric key is displayed
when the QWERTY keyboard is displayed
horizontal.
Overwrite handwritten input*3 :
enable handwriting input when the QWERTY
keyboard or Japanese syllabary keyboard is
displayed.
Number of input boxes (Vertical display)*3 :
number of input boxes for handwriting input in the
portrait display mode.
Number of input boxes (Horizontal display)*3 :
number of input boxes for handwriting input in the
landscape display mode.
Recognition speed*3 :
handwritten input.
Handwriting gesture*3 :
to delete a character or enter a space.
*1 Setting for numeric keyboard.
*2 Setting for QWERTY keyboard.
*3 Setting for handwritten input.
In the flick input mode, you can
When this checkbox is
When this checkbox is
Mark to insert a space
When this
When this
Set whether to
Set the
Set the
Set recognition speed for
Show gesture for operation
38
Before using the terminal
❖
Entry/Conversion settings
From the Applications menu, [Settings]
1
[Language & input]→[Configure input
methods]
→
[Entering / Converting]
Set each item
2
Input prediction :
predictive conversion candidates are displayed.
Showing prediction candidates before next input :
When this checkbox is marked with predictive
conversion enabled, input predictive candidates are
displayed before the next character is entered.
Use half-width space ：
entering Japanese characters.
❖
Initializing learning data
Once a phrase or expression is entered, it is automatically
stored in memory, and is displayed as a predictive
conversion candidate. All learned data can be deleted and
the terminal can be reset to its default state by initializing
learned data.
From the Applications menu, [Settings]
1
[Language & input]→[Configure input
methods]
[Entering / Converting]
[Initializing learning data]→[OK]
2
[Settings] under "NX!input"
When this checkbox is marked,
Enter a one-byte space when
→
[Settings] under "NX!input"
→
→
→
→
❖
Changing the keyboard design
From the Applications menu, [Settings]
1
[Language & input]→[Configure input
methods]
→
[Design]
Set each item
2
Theme :
keyboard.
Simple design :
Key size (vertical screen) :
portrait view.
Key size (horizontal screen) :
landscape view.
Font size :
number of lines to display (vertical screen) :
number of lines to display conversion candidates in
the portrait view.
number of lines to display (horizontal screen) :
number of lines to display conversion candidates in
the landscape view.
❖
User dictionary
You can register frequently used words to a user
dictionary in advance. When you enter characters with the
same reading, words in the user dictionary will be given
priority over other conversion candidates and displayed
first.
■
Registering words to a user dictionary
From the Applications menu, [Settings]
1
[Language & input]→[Configure input
methods]
[Tools]→[Dictionary utility]
2
Enter the word to register in "単語 (Word)"
3
[Settings] under "NX!input"
Set the design theme of the ATOK software
Make keyboard design simple.
Set the keypad size in the
Set the keypad size in the
Set the text size of conversion candidates.
→
[Settings] under "NX!input"
→[新規登録
(New)]
→
→
Set the
Set the
→
→
39
Before using the terminal
Enter the reading in "読み (Reading)"
4
Select the part of speech→[登録 (Register)]
5
■
Editing registered words
In the dictionary utility screen, select the
1
word you want to edit
Modify the registered content,→[修正 (Edit)]
2
■
Deleting registered words
In the dictionary utility screen, select a word
1
you want to delete (1 sec. or more)
(Delete)]
→[はい
Deleting all words : In the dictionary utility screen,
→[全削除
■
Saving registered words to microSD card
In the dictionary utility screen, →[
1
力
(Output list)]
On the "場所 (Output to)" field, select
2
[sdcard]
registered words in
Enter a file name→[OK]→[実行 (Execute)]→[
3
閉じる
✔
INFORMATION
･
To read word data saved on the microSD card, in the
dictionary utility screen,
→
In the "場所 (Output to)" field, [sdcard]→Select a folder
→
Select a file→[OK]→[登録 (Register)]→Tap [
(Close)]. To register words learned automatically by
confirmation of character entry, unmark [
含めない
(Not include auto registered words)].
(Yes)]
(Delete all)]→[はい (Yes)]
→
Select a folder to save the
(Close)]
→[一括登録
(Batch register)]
自動登録単語は
→[削除
一覧出
閉じる
❖
Adding common phrases
From the Applications menu, [Settings]
1
[Language & input]→[Configure input
methods]
→
[Tools]→[Common phrase utility]
The common phrase list screen is displayed.
･
(New)] to add a new category.
2
Enter a common phrase→Select a category
3
in the "
(Register)]
❖
Editing common phrases
■
Editing the body text of common phrases
Select a common phrase you want to edit in
1
the common phrase list screen
Enter the changes→[登録 (Register)]
2
･
When the body text of a newly created common
phrase is edited, changes will also be made to its
title. To disable the link between a title and body
text, changing the title of a common phrase.
■
Changing the title of a common phrase
Select a common phrase whose title you
1
want to change in the common phrase list
screen (1 sec. or more)
[
タイトル変更
2
changes
[Settings] under "NX!input"
→[カテゴリー
→[新規作成
(Category)]
(New)]
カテゴリー
(Change title)]→Enter the
→
[OK]
→
→
→→
Tap [
新規作成
(Category)" field→[登録
40
Before using the terminal
■
Changing the category of a common phrase
Select a common phrase whose category
1
you want to change in the common phrase
list screen (1 sec. or more)
[
カテゴリー移動
2
category in the destination
■
Deleting a common phrase
Select a common phrase you want to delete
1
in the common phrase list screen (1 sec. or
more)
[削除 (Delete)]→[はい (Yes)]
2
✔
INFORMATION
･
To return common phrase data to its default state, on the
common phrase list screen,
Tap [はい (Yes)].
❖
Initializing ATOK settings
Initialization returns ATOK settings to their default state.
From the Applications menu, [Settings]
1
[Language & input]→[Configure input
methods]
[Initializing settings]→[OK]
✔
INFORMATION
･
Learned data, words in the user dictionary and additional
common phrases are not deleted even if ATOK settings
are initialized.
(Move category)]→Select a
→[初期化
(Initialize)]
→
[Settings] under "NX!input"
→
→
→
◆
Editing text
You can copy texts in the character entry field, web page,
document or received mail and cut and paste texts in the
character entry field.
･
Operations may differ depending on the application
type.
❖
Copying/Cutting texts
Touch and hold a text for 1 second or more
1
Selected text is highlighted in yellow green.
･
You can also select by tapping [Select all].
･
Slide knobs on the both end of text range to adjust
selected range.
･
To deselect, tap out of selected range or tap [Done].
[Copy]/[Cut]
2
❖
Pasting a text
Move the cursor to the destination to paste
1
→
Touch and hold text for 1 second or more
→
[Paste]
The text on the clipboard is pasted to the cursor
position.
･
Tap [Paste] after selecting range to overwrite the
selected range with pasted text.
◆
Password manager
Register authenticate information such as ID (account) or
password and quote the stored data to enter.
･
Up to 50 passwords can be stored.
❖
Store/Edit password
From the Applications menu, [Password
1
manager]
41
Before using the terminal
Enter master password→[OK]
2
Store master password : Enter a new password
Enter the same password→[OK]
Change master password : →[Change master
password]→Enter the master password→[OK]
Enter a new master password→Enter the same
password→[OK]
→
Set required items→[OK]
3
Change password : Select a title from the password
title list
→→
Delete password : Select a title from the password
title list
Delete all passwords : →[Delete all]→[OK]
✔
INFORMATION
･
If you enter a wrong master password 3 times, Password
Manager ends.
❖
Quoting stored password
While entering characters,
1
keyboard.
PasswordManager activates.
Enter master password→[OK]→Select a
2
title
→
Change required items→[OK]
→→
[OK]
→
in the "ID (account)" or
on the
"Password" field
Stored "ID (account)" or "Password" is entered in the
character entry field.
･
Touch and hold characters in the "ID (account)" or
"Password" field for 1 second or more to copy the
characters on the clipboard.
Lock/Security
→
◆
Security codes for the terminal
→
Some functions provided for convenient use of the
terminal require the security code to use them. Besides the
security code for locking the terminal, the network security
code necessary for the network services etc. are available.
Make use of the terminal using an appropriate security
code according to your purpose.
Notes on the security codes
･
To set a security code, avoid imaginable numbers
such as "birth date", "a part of phone number",
"street address or room number", "1111" or "1234".
Maintain a separate record not to forget the
numbers.
･
Be careful never to reveal your security code to
others. If a security code is misused by others,
DOCOMO assumes no responsibility for damages
resulted from it.
･
If you forget your security codes, you need to bring
a document (a drivers license etc.) to identify your
subscription, the terminal and the docomo mini
UIM card to a docomo Shop. For details, contact
"General Inquiries" on the last page of this manual.
･
The PUK code is written on a subscription form
(copy for user) handed at subscription in a docomo
Shop. For users subscribed in other than docomo
Shop, bring a document (a drivers license etc.) to
identify your subscription and the docomo mini
UIM card to a docomo Shop, or contact "General
Inquiries" on the last page of this manual.
42
Before using the terminal
❖
Network security code
The network security code is a 4-digit number necessary
for identification or using the docomo Network Services at
reception of your request in docomo Shop or at a docomo
Shop or docomo Information Center. It can be set any
number at the subscription and also changed later by
yourself.
You can change your network security code to the new one
using the PC if you have the "docomoID/Password" for the
"My docomo"* General support site for PC.
*
For "My docomo", see the previous page of the last page of this
manual (for Instruction Manual, "
ましょう
(Using mobile phone with your manners!)" in "
(Appendix)").
❖
PIN code
A security code named PIN code can be set to docomo
mini UIM card. The PIN code is set to "0000" by default,
which you can change by yourself.→P43
PIN is a 4- to 8-digit number (code) that must be entered for
user confirmation to prevent unauthorized use by a third
party every time you insert the docomo mini UIM card into
the terminal or when the terminal is powered ON. Entering
the PIN code enables terminal operation.
･
For using the docomo mini UIM card that you have used
on another terminal by inserting to this terminal, use the
set PIN code on the former terminal. If you did not
change the setting, the code is "0000".
･
If you enter a wrong PIN code 3 times consecutively, the
PIN code is locked and cannot be used anymore. In this
case, unlock with "PUK".
❖
PUK code
The PUK code is an 8-digit number for canceling the locked
PIN code. The PUK code cannot be changed by yourself.
･
If you enter a wrong PUK code 10 times consecutively,
the docomo mini UIM card is locked. Please contact a
docomo Shop.
マナーもいっしょに携帯し
付録
◆
Setting the PIN code
❖
Setting up SIM card lock
Set PIN code to be entered when the terminal is turned ON.
From the Applications menu, [Settings]
1
[Location & security]→[Set up SIM card
lock]
[Lock SIM card]→Enter the PIN code→[OK]
2
[Lock SIM card] is marked.
･
To cancel the setting, [Lock SIM card]→Enter PIN
code→[OK] to unmark.
✔
INFORMATION
･
When entering the PIN code for the first time, enter
"0000".
❖
Changing the PIN code
To change the PIN code, set the PIN code (mark [Lock SIM
card]) in advance.
From the Applications menu, [Settings]
1
[Location & security]→[Set up SIM card
lock]
[Change SIM PIN]
2
Enter the current PIN code→[OK]
3
Enter the new PIN code→[OK]
4
Re-enter the new PIN code→[OK]
5
❖
Entering the PIN code
Turn power ON→Enter the PIN code in the
1
PIN entry screen
→
[OK]
→
→
43
Before using the terminal
❖
Disabling the PIN lock
When the PIN code is locked, [Unlock PIN
1
lock]
Enter [**05* [PUK] * [new PIN code] * [new
2
PIN code] #]
･
For example, to change the PIN code to 7777 when
the PUK is 88888888, enter
"**05*88888888*7777*7777#".
◆
Screen lock
If the screen lock is set, authentication is required when
resuming from the sleep mode or turning the power on,
which prevents others from misusing the terminal.
･
For the screen lock you can select unlock method from 3
types: pattern, security code and password.
❖
Setting screen lock
Set unlock method to activate screen lock.
･
When you change pattern, security code or password,
set again.
From the Applications menu, [Settings]
1
[Location & security]→[Configure lock
→
screen]
･
When the screen lock is activated, unlocking is
required after tapping [Configure lock screen].
[Off]/[None]/[Pattern]/[Security code]/
2
[Password]
Disable screen lock : [Off]
Do not protect with security : [None]
･
Unlock screen appears but the terminal is not
protected with security.
Entering pattern to unlock : [Pattern]→Slide like
jointing at least four points vertically, horizontally
and diagonally to enter a pattern→[Continue]
Enter the same pattern→[Confirm]
→
･
When you set for the first time, example pattern
appears.
Entering security code to unlock : [Security code]
Enter the 4- to 16-digit security code→[OK]
Reenter the security code→[OK]
Entering password to unlock : [Password]→Enter the
4- to 16-digit password including alphabets
[Continue]→Reenter the password→[OK]
✔
INFORMATION
･
To set time for locking the screen after going into the
sleep mode, from the Applications menu, tap [Settings]
[Location & security]→[Timeout]→Tap a time you want
to set.
･
If you do not want to display the pattern when unlocking
the screen, from the Applications menu, tap [Settings]
[Location & security]→[Use visible pattern] to unmark.
･
To enable vibration when entering the pattern, from the
Applications menu, tap [Settings]
→
[Use tactile feedback] to mark.
❖
Manual screen lock
X
1
The terminal goes into sleep mode and the screen lock
is activated.
→
[Location & security]
→
→
→
→
→
44
Before using the terminal
❖
Unlocking the screen
During sleep mode,
1
･
When turning the pow er on, the lock screen appears
following the startup screen.
Deactivate the screen lock according to the
2
screen lock type.
When [None] is set : Slide on the lock screen to the
outside of the circle.
When [Pattern] is set : Enter the pattern
When [Security code] is set : Enter the security code
→
[OK]
When [Password] is set : Tap the password entry field
→
Enter password→[OK]
❖
If you forget the unlock method
When you forget the unlock screen method, set a new
pattern/security code/password in the following procedure
to unlock the screen.
･
If you fail entering unlock pattern, security code or
password 5 times, retry 30 seconds later.
･
Perform the following steps while signing in with the
Google account.
On the unlock screen, [Forgot pattern?]/
1
[Forgot security code?]/[Forgot password?]
→
Sign in with the Google account→Follow
X
the onscreen instructions to set a new
pattern/security code/password
❖
Displaying the owner info
You can display the owner's information on the lock
screen.
From the Applications menu, [Settings]
1
[Location & security]→[Owner info]→Mark
[Show owner info on lock screen]
Enter the owner's information
2
◆
Displaying passwords
You can set to display entered characters when entering a
password.
From the Applications menu, [Settings]
1
[Location & security]→Mark [Visible
passwords]
→
→
45
Before using the terminal
◆
Managing authentication
information
You can install authentication information for accessing
security-protected Wi-Fi networks or VPNs or other
certificates from the microSD card. You can also set a
password to authentication information storage for saving
authentication information and certificates.
❖
Setting password for authentication
information storage
From the Applications menu, [Settings]
1
[Location & security]→[Set password]
Enter a password→Enter the password
2
again
→
[OK]
❖
Enabling authentication information
and certificates
You can enable authentication information and certificates
by allowing applications on the terminal to access
authentication information storage set with a password.
･
Set a password to certification information storage in
advance.
From the Applications menu, [Settings]
1
[Location & security]
Mark [Use secure credentials]
2
Enter the password for the authentication
3
information storage
→
[OK]
→
→
❖
Clearing authentication information
storage
You can clear all authentication information or certificates
from the authentication information storage to reset the
storage password.
From the Applications menu, [Settings]
1
[Location & security]→[Clear credentials]
[OK]
❖
Installing authentication information
or certificates from the microSD card
From the Applications menu, [Settings]
1
[Location & security]→[Install from SD card]
Select the authentication information/
2
certificate you want to install
If necessary, enter the password→[OK]
3
Enter the name of the authentication
4
information/certificate
･
If a password is not set to the authentication
information storage, follow the onscreen
instructions to set the password.
◆
Encrypting data on the terminal
Encrypting data prevents the others from viewing the data
on the terminal via a PC, when the terminal is misplace or
stolen.
･
If encrypted, the data will be decrypted after turning the
power on and entering the PIN code.
･
Before encrypting, make sure to check the onscreen
explanation.
From the Applications menu, [Settings]
1
[Location & security]→[Encrypt phone]
[Encrypt phone]
2
46
→
[OK]
Before using the terminal
→
→
→
→
Contacts
Using Contacts
You can enter phone numbers and email addresses to
Contacts. You can contact registered parties through
simple operation from Contacts.
From the Applications menu, [Contacts]
1
a b c d e f
g
i
h
a
Select groups to be displayed.
b
Tap to enter a keyword to search contact.
c
Tap to save to the group of the Contacts "Starred".
d
Store a new contact.
e
Edit a contact.
f
Display the Contacts submenu.
g
Contacts list
Select contacts. Tap on the contacts list, the index
is displayed.
h
Name
Tap to display information on the personal
information screen.
i
Index bar
j
Personal information screen
Display personal information of the selected party.
Tap an item to send an SMS or email.
k
Index
Select a character or name to search contact. Tap
the contacts list→Select a character on the index
Slide to the next layered character→Slide to a
name of saved contact. Selected contact is
displayed at the top of the contacts list. However, if
there are a few saved items, it may not be
displayed at the top of the list.
❖
Setting the contacts to be displayed
in the Contacts list
You can change groups to be displayed or set to show or
hide contacts that are included in specified accounts or
groups of Google accounts.
j
k
In the contact screen,
1
[Customize...]→Set contacts to be
displayed
❖
Contacts sub-menus
In the contact screen, tap to display the profile, set an
account, import/export contacts, add groups, send a
contact, delete contacts.
47
→
→
Contacts
◆
Displaying contacts by group
You can display contacts data by group specified in
registration.
In the contact screen,
1
group
❖
Creating a new group
From the Contacts submenu, you can create a group,
rename group name or delete a group.
In the contact screen, →[Add Group]
1
Select an account as required→Enter a
group name
･
Creating groups is available only for docomo
account or Google account.
Renaming group name : In the contact screen,
group name]→Rename the group name→[OK]
Deleting a group : In the contact screen,
Select a group
✔
INFORMATION
･
You cannot rename/delete in "No groups" and Google's
default groups.
◆
Registering a contact
In the contact screen,
1
account as required
→
[OK]
→
Select a group
→→
[Delete group]→[OK]
→
Set each item
→
→→
[Rename
→
Select an
Select a
→
[Done]
◆
Editing contacts
In the contact screen, select a contact you
1
want to edit
→→
Enter items to edit
[Done]
◆
Deleting a contact
In the contact screen, select a contact you
1
want to delete
→→
[OK]
･
In the contact screen, →Tap [Delete Selected
Contacts] to select and delete a contact you want to
delete. Tap [Select all] to delete all the contacts.
◆
Importing/Exporting contacts
→
→
In the contact screen, →[Import/Export]
1
→
Select an item→Perform each operation
Import from SIM card :
to add from contacts saved on the docomo mini
UIM card to import them.
Export to SIM card :
docomo mini UIM card. Only names/first registered
→
phone numbers/first mail addresses are exported. Up
to 50 contacts can be saved. But the properties of the
phone numbers and mail addresses are not exported.
When you export on overwriting, note that all contacts
saved in the docomo mini UIM card are deleted first,
and then new contacts are exported.
Import from SD card :
(vCard file) saved in microSD card to specified
account. When there are multiple files, select a file
to register.
Export to SD card :
except "Profile" to microSD card.
Share visible contacts :
Bluetooth or mail attachment.
✔
INFORMATION
･
If you want to exchange all contacts data with another
terminal, use PhoneBookCopy (
･
For sending all items to a terminal other than
smartphone, use PhoneBookCopy. Data cannot be
transferred correctly by sending all items via Bluetooth
communication.
Specify the contacts you want
Export specified contacts to the
Register the contacts data
Save all contacts data (vCard file)
Send all contacts data via
48
[Delete contact]
→
P49).
→
Contacts
PhoneBookCopy
You can copy phonebook data to/from another terminal
by using a microSD card. You can also copy phonebook
data registered to a Google account to the docomo
account.
From the Applications menu,
1
[PhoneBookCopy]
･
When you activate PhoneBookCopy for the first
time, agree to "
Agreement)".
◆
Exporting phonebook data to a
microSD card
Attach a microSD card to the terminal
1
In the "
2
(Start)"
The phonebook data saved in the docomo account is
saved to the microSD card.
◆
Importing phonebook data from a
microSD card
Attach the microSD card on which the
1
phonebook data is saved into the terminal
In the "
2
you want to import
追加
(Add)]
The imported phonebook data is saved to the docomo
account.
使用許諾契約書
エクスポート
インポート
(License
(Export)" tab, tap "開始
(Import)" tab, tap a file
→[上書き
(Overwrite)]/[
◆
Copying contacts in a Google
account to the docomo account
In the "docomo
1
docomo account)" tab, tap a Google
account you want to copy
(Overwrite)]/[
The copied phonebook data is saved to the docomo
account.
･
It is possible to copy phonebook data registered in
the "本体 (Phone contacts)" to the docomo account
in the same way as a Google account.
✔
INFORMATION
･
If the item name (e.g. Phone number, etc.) of another
terminal is different from those in the terminal, the item
name may be changed or deleted. Also, some text may
be deleted in copied destination, because savable
characters in a contact vary by the terminal.
･
When exporting phonebook to microSD card, data
without name cannot be copied.
･
When importing phonebook data from a microSD card,
files created using [
cannot be read.
アカウントへコピー
追加
一括バックアップ
→[上書き
(Add)]
(Backup all at once)]
(Copy to
Editing owner info
You can check your own phone number. You can also
enter and edit your own information.
From the Applications menu, [Contacts]
1
[Profile]
→→
→
Set each item→[Save]
→
49
Contacts
Settings
Setting menu
You can make various settings in the menu displayed by
selecting [Settings] from the Applications menu.
Initial setting :
time to use.
Wireless & networks :
function or Tethering.
Sound :
operation sound, Dolby Mobile setting, etc.
Screen :
Animation, font, etc.
Location & security :
password, etc.
Applications :
Accounts & sync :
synchronization.
Privacy :
Storage :
external storage, etc.
Language & input :
recognizer settings, Text-to-speech settings or
Keyboard settings.
Accessibility :
before touch and hold is recognized when tapping.
Date & time :
About phone :
✔
INFORMATION
･
See "Initial setting" (→P27) for default settings and see
"Setting the location information service" (
information about current location, "Lock/Security" (
P42) for security.
Display items you need to set for the first
Set Airplane mode, Wi-Fi, Bluetooth
Set vibration, Manner mode, Notifications,
Set Photo Screen, Brightness, Auto-rotate screen,
Set My Location, screen lock,
Make settings about applications.
Make settings about accounts or
Backup, restore or reset data.
Display amount of space, erase data in the
Set language to be used, Voice
Enable/Disable accessibility or set the time
Make settings about date and time.
Display various information of the terminal.
→
P87) for
→
Wireless & networks
･
For Bluetooth function, see "Bluetooth communication"
(→P76).
◆
Setting access point (APN)
Access points for connecting to the Internet (sp-mode,
mopera U) are already registered. You can add or change
it if necessary.
･
By default, sp-mode is set for the usual access point.
･
When Wi-Fi tethering is set to ON, you cannot set an
access point. Turn Wi-Fi tethering OFF→P54
❖
Checking the access point in use
From the Applications menu, [Settings]
1
[Wireless & networks]→[Mobile networks]
→
[Access Point Names]
❖
Adding new access point (New APN)
･
Do not change the MCC/MNC to other than 440/10. The
settings disappears from the screen.
From the Applications menu, [Settings]
1
[Wireless & networks]→[Mobile networks]
→
[Access Point Names]
→
[New APN]
2
[Name]→Enter a network profile→[OK]
3
[APN]→Enter the access point name→[OK]
4
Enter other items required by network
5
✔
INFORMATION
･
If you have changed MCC/MNC settings and they do not
appear on the APN name screen, reset to default or make
APN settings on [New APN].
50
operator
→
→
→
Settings
❖
Initializing an access point
By initializing an access point, the default state is restored.
From the Applications menu, [Settings]
1
[Wireless & networks]→[Mobile networks]
→
[Access Point Names]
→
[Reset to default]
2
❖
sp-mode
sp-mode is ISP for NTT DOCOMO smartphone. In addition
to accessing Internet, you can use the mail service using
the same address as i-mode mail (@docomo.ne.jp), etc.
･
sp-mode is a service requiring subscription. For details
on sp-mode, refer to NTT DOCOMO website.
❖
Setting mopera U
mopera U is ISP of NTT DOCOMO. If you have subscribed
to mopera U, you can use Internet after making the simple
settings.
･
mopera U is a service requiring subscription.
From the Applications menu, [Settings]
1
[Wireless & networks]→[Mobile networks]
→
[Access Point Names]
Mark [mopera U]/[mopera U設定 (mopera U
2
settings)]
✔
INFORMATION
･
[mopera U設定 (mopera U settings)] is an access point for
setting mopera U. When you use the access point for
setting mopera U, packet communication charges for
setting do not apply. Note that you can set only the initial
setting screen or the change setting screen. For details on
mopera U settings, refer to mopera U website.
･
To use [mopera U], subscription to flat-rate data plan is
required. For details on mopera U, refer to NTT DOCOMO
website.
→
→
◆
Setting Airplane mode
When Airplane mode is set, wireless functions of the
terminal (packet communication, Wi-Fi, tethering,
Bluetooth functions) are disabled.
From the Applications menu, [Settings]
1
[Wireless & networks]
Mark [Airplane mode]
2
◆
Wi-Fi
With Wi-Fi function of the terminal, you can use mail or
access Internet by connecting to home or company
network or wireless LAN access point of public wireless
LAN service.
To connect to a LAN access point, you need to set
connection information.
■
Reception interference caused by Bluetooth
Wireless LAN (IEEE 802.11b/g/n) and Bluetooth function
use the same frequency band (2.4 GHz). If you use the
wireless LAN function and Bluetooth function of the
terminal at the same time, reception interference may
occur or the communications speed may lower. Also, you
may hear noise or have a connection problem.
Even when you use only wireless LAN function of the
terminal, the same problem may occur when someone
uses a Bluetooth device near you. In these cases, do the
following.
･
Keep the terminal over 10 meters away from a Bluetooth
device.
･
Within 10 meters, turn off the Bluetooth device.
■
Available channels
1 - 13 channel frequency bands can be used in Japan, and
1 - 11 channel frequency bands overseas.
→
51
Settings
❖
Connecting to network with Wi-Fi ON
From the Applications menu, [Settings]
1
[Wireless & networks]
Mark [Wi-Fi]
2
Wi-Fi is ON and available Wi-Fi networks are scanned.
[Wi-Fi settings]
3
Detected Wi-Fi network names and the security
settings (open network or protected network) are
displayed in Wi-Fi network list.
Select a Wi-Fi network→[Connect]
4
･
When you select a Wi-Fi network protected by
security, enter a password (security key) and tap
[Connect].
✔
INFORMATION
･
Even when Wi-Fi is ON, packet communication is
available. However, while you connect Wi-Fi network, WiFi comes first. When the Wi-Fi network is disconnected, it
switches to LTE/3G/GPRS network connection
automatically. Note that packet communication fee
applies for using 3G/GPRS network.
❖
Notification of open network
Set to notify you when Wi-Fi open network is detected.
･
Set Wi-Fi to ON in advance.
From the Applications menu, [Settings]
1
[Wireless & networks]→[Wi-Fi settings]
Mark [Network notification]
2
❖
Scanning Wi-Fi network
･
Set Wi-Fi to ON in advance.
→
→
From the Applications menu, [Settings]
1
[Wireless & networks]→[Wi-Fi settings]
→
[Scan]
2
Scanning for Wi-Fi networks starts. Detected Wi-Fi
networks displayed in the Wi-Fi network list.
❖
Simple registration of Wi-Fi network
You can connect through simple operations if connecting
via a Wireless access point supporting AOSS or WPS.
･
Set Wi-Fi to ON in advance.
From the Applications menu, [Settings]
1
[Wireless & networks]→[Wi-Fi settings]
[Easy Wi-Fi registration]
Select a registration method
2
AOSS system : [AOSS system]→[Yes]→Press
AOSS button on the Access point→[OK]
WPS system : [WPS system]→[Push button system]/
[PIN entry system]→[Yes]→On the access point,
perform operations
･
In case of push button method, press a dedicated
button on an access point. In case of PIN entry
method, enter PIN code displayed on the terminal to
an access point and tap [OK].
✔
INFORMATION
･
AOSS connection may not be available depending on
the LAN access point. If connection is failed, connect by
WPS system or manually.
→
→
→
52
Settings
❖
Adding Wi-Fi network
Enter network SSID or security to add Wi-Fi network
manually.
･
Set Wi-Fi to ON in advance.
From the Applications menu, [Settings]
1
[Wireless & networks]→[Wi-Fi settings]
[Add Wi-Fi network]
2
Enter a network SSID of Wi-Fi network to
3
→
Select security
add
･
Security can be set to [None], [WEP], [WPA/WPA2
PSK] or [802.1x EAP].
Enter additional security information as
4
required
→
[Save]
❖
Using static IP address for connection
You can set to connect to a Wi-Fi network using a static IP
address.
From the Applications menu, [Settings]
1
[Wireless & networks]→[Wi-Fi settings]
Select a Wi-Fi network to connect
2
[IP settings]→[Static]
3
Select [IP address] and the other items
4
Enter necessary information
･
Enter [IP address], [Gateway], [Network prefix
length] and [DNS 1] to enable a static IP address.
→
→
→
❖
Disconnecting Wi-Fi network
From the Applications menu, [Settings]
1
[Wireless & networks]→[Wi-Fi settings]
Select a connected Wi-Fi network→[Forget]
2
✔
INFORMATION
･
When you disconnect Wi-Fi network turning Wi-Fi OFF,
connection is automatically made if available Wi-Fi
network exists when Wi-Fi is turned ON next time.
❖
Wi-Fi auto disconnect settings
Set operations of Wi-Fi function when the terminal screen
is OFF or during charge.
From the Applications menu, [Settings]
1
[Wireless & networks]→[Wi-Fi settings]
[Wi-Fi disconnect policy]
2
[When screen turns off (uses more mobile
3
data)]/[Never when plugged in]/[Never
(uses more battery power)]
❖
Checking MAC address/IP address
From the Applications menu, [Settings]
1
[Wireless & networks]→[Wi-Fi settings]
→
[Advanced]
2
→
→
→
53
Settings
◆
Tethering
Tethering is a feature to allow the mobile device such as
smartphone to function as a modem so that the external
device connected by USB cable or Wi-Fi can access
Internet.
･
When tethering is enabled, sp-mode functions other
than Internet connection and mail service are not
available.
･
When you connect to Internet using tethering, Wi-Fi
device applications such as web browser or game may
not work properly depending on the use conditions.
✔
INFORMATION
･
To see the information about tethering, from the
Applications menu, [Settings]
[Tethering]→[Help].
◆
USB tethering
You can access Internet by connecting the terminal to a PC
with the included PC connection USB cable T01 and using
the terminal as a modem.
Connect the terminal and a PC with the USB
1
cable
From the Applications menu, [Settings]
2
[Wireless & networks]→[Tethering]
Mark [USB tethering]
3
Check the precautions and [OK]
4
✔
INFORMATION
･
System requirements for USB tethering are as follows.
Operations on upgraded OS or added/modified
environment are not guaranteed.
- Windows XP (Service Pack 3 or later), Windows Vista,
Windows 7
→
[Wireless & networks]
→
･
To use USB tethering for Windows XP, install dedicated
driver to a PC. For information on how to download the
driver, refer to the following website.
http://www.fmworld.net/product/phone/usb/
･
To disable USB tethering on a Windows XP PC, remove
the USB cable from the PC without setting "USB
tethering" to "OFF".
◆
Wi-Fi tethering
You can allow Wi-Fi devices to access Internet by using the
terminal as Wi-Fi hotspot.
･
You can connect up to 8 Wi-Fi devices.
･
1 - 13 channel frequency bands can be used in Japan,
and 1 - 11 channel frequency bands overseas.
→
❖
Setting Wi-Fi tethering
Set Wi-Fi tethering to ON for connection setting
From the Applications menu, [Settings]
1
[Wireless & networks]→[Tethering]
Mark [Wi-Fi tethering]
2
･
Unmark to turn off Wi-Fi tethering.
Check the precautions and [OK]
3
[Network SSID]→Enter a network SSID
4
･
By default, "F-01D_AP" is set.
･
To change the registered settings, select [Configure
Wi-Fi tethering] to display the setting screen.
[Security]→Select a security
5
･
Security can be set to [Open], [WEP64], [WEP128],
[WPA PSK TKIP], [WPA PSK AES], [WPA2 PSK
TKIP], [WPA2 PSK AES] or [WPA/WPA2 PSK].
[Password]→Enter a password→[Save]
6
→
54
Settings
❖
Easy registration of Wi-Fi device
Register Wi-Fi devices supporting AOSS.
･
Set Wi-Fi tethering to ON in advance.
From the Applications menu, [Settings]
1
[Wireless & networks]→[Tethering]→[Easy
Wi-Fi registration]
Select a registration method
2
AOSS system : [AOSS system]→[Yes]→Press
AOSS button on the Wi-Fi device→[OK]
WPS system : [WPS system]→[Push button system]/
[PIN entry system]→Perform operations→On the
registration screen, [OK]
･
In case of push button method, tap [OK] and press a
dedicated button on the Wi-Fi device. In case of PIN
entry method, enter PIN code displayed on the WiFi device and tap [OK].
✔
INFORMATION
･
When number of AOSS registration devices exceeds
24, a confirmation screen for deleting old registration
appears. To use AOSS
[Yes].
･
To cancel the AOSS setting, tap [AOSS OFF] in the
[Configure Wi-Fi tethering] screen.
･
AOSS connection may not be available depending on
the Wi-Fi device. If connection is failed, connect by WPS
system or manually.
connection with new device, tap
◆
Connecting VPN (Virtual Private
Network)
VPN (Virtual Private Network) is a technology to connect to
the information in a protected local network such as
→
enterprises or universities from another network. To set up
a VPN connection from the terminal, you need to retrieve
the information related to security from your network
administrator.
･
When ISP is set to sp-mode, PPTP is not available.
❖
Adding a VPN
From the Applications menu, [Settings]
1
[Wireless & networks]→[VPN settings]
[Add VPN]→Select a VPN type to add
2
Set required items for VPN settings
3
･
For setting details, follow the instruction of the
network administrator.
→
[Save]
4
A new VPN is added in the list on VPN settings screen.
❖
Connecting to VPN
From the Applications menu, [Settings]
1
[Wireless & networks]→[VPN settings]
Added VPNs are displayed in the list on the VPN
setting screen.
Select a VPN to connect to
2
Enter necessary authentication information
3
→
[Connect]
When you are connected, a notification icon appears
on the status bar.
→
→
55
Settings
❖
Disconnecting VPN
Open the Notification panel
1
Select a notification of VPN connecting
2
･
When VPN is disconnected, the notification icon on
the status bar turns to gray. To reconnect, open the
Notification panel and select the notification.
◆
Stopping packet connection
･
Some applications automatically perform packet
communications. Packet communication is kept active
unless you disconnect it or the time-out is occurred.
From the Applications menu, [Settings]
1
[Wireless & networks]→[Mobile networks]
Unmark [Data enabled]
2
✔
INFORMATION
･
To switch ON/OFF for packet communications, paste
[Data communiation] of widgets on the Home screen.
P30
Sound settings
◆
Setting Silent mode
Mute sounds such as mail ringtone, alarm, media play
sound, etc. that are emitted from the terminal.
From the Applications menu, [Settings]
1
[Sound]→[Manner mode]
Mark [Enable manner mode]
2
Icons appear on the status bar. Icon varies by the
manner mode type. For each icon, see "Icons on the
status bar".→P27
✔
INFORMATION
･
Even in Manner mode, shutter sound are emitted.
❖
Changing manner mode type
From the Applications menu, [Settings]
1
[Sound]→[Manner mode]→[Select manner
mode]
Selecting an item
2
Manner mode :
terminal.
Manner mode (Silent) :
→
→
→
turn off the vibration.
Manner mode (Alarm) :
terminal only. Vibrate turns to off except for being
set to "Always" in each application.
Original manner :
for each sound type. Settings in Original manner
take precedence of sound volume/vibrate setting in
each application.
❖
Setting original manner
From the Applications menu, [Settings]
1
[Sound]→[Manner mode]→[Original
manner settings]
[Volume]
2
[Media volume]/[Alarm volume]/
3
[Notification volume]
Slide the slider to adjust sound volume
4
[OK]
[Vibration]
5
Mark/Unmark [Alarm]/[Notification]
6
Mute sounds emitted from the
Set sound volume and the vibration
→
→
In addition to mute sounds,
Sound alarm sound from the
→
→
56
Settings
◆
Volume
You can adjust volume of media playing sound, alarm
sound and notification sound.
From the Applications menu, [Settings]
1
[Sound]→[Volume]
Slide the slider to adjust sound volume
2
[OK]
◆
Setting input microphone
Set sound input microphone when the commercially
available stereo earphone set is connected to the stereo
earphone jack of the terminal.
･
This setting can be made even while stereo earphone set
is connected→P83
From the Applications menu, [Settings]
1
[Sound]→[MIC Input]
[Phone MIC]/[Headset MIC]
2
･
When you connect a stereo earphones without
microphone, select [Phone MIC].
→
→
→
◆
Setting Notification ringtone/
Audible touch tones/Vibrate
From the Applications menu, [Settings]
1
[Sound]
Set each item
2
Notification ringtone :
notification ringtone.
Audible selection :
for selecting menu.
Screen lock sounds :
setting and canceling screen lock to ON/OFF.
Haptic feedback :
keyboard operation to ON/OFF.
◆
Dolby Mobile settings
Set Dolby function when playing moving pictures or
music.
From the Applications menu, [Settings]
1
[Sound]→[Dolby Mobile setting]
[Use with video genre setting]/[Use with
2
music genre setting]
Set genre for [Video genre setting]/[Music
3
genre setting]
appears on the status bar. Icon varies by genre.
✔
INFORMATION
･
By default, only [Music] operates for [Auto effect setting].
Set ringtone to be used as
Switch operation sound to ON/OFF
Switch notification sound for
Switch vibration for software
→
→
57
Settings
Screen settings
◆
Setting background image for lock
screen
From the Applications menu, [Settings]
1
[Screen]→[Photo Screen]
[Picture settings]→Set each item
2
None :
Display the wallpaper of Home screen.
Folder :
Display images in selected folder in
slideshow.
Flickr :
Obtain images matching a keyword from Flickr
automatically and display them in slideshow.
Picasa :
Obtain images matching a keyword from
Picasa and display them in slideshow.
･
When you select [Flickr]/[Picasa], enter a search tag
and set [Update interval] and [Network to be used].
･
When you select [Specified time] in [Update
interval], tap [Update time] to specify time.
✔
INFORMATION
･
Time specified in [Update time] is time to start to obtain
images automatically. It is not time to display obtained
images.
◆
Changing screen display
❖
Backlight settings
Make setting for screen brightness.
From the Applications menu, [Settings]
1
[Screen]→[Brightness]
･
To set auto-adjust brightness according to ambient
condition, mark [Automatic brightness], tap [OK].
Slide the slider to adjust brightness→[OK]
2
❖
Auto-rotate screen
From the Applications menu, [Settings]
1
[Screen]
Mark/Unmark [Auto-rotate screen]
2
→
✔
INFORMATION
･
Some applications such as camera or video record are
not according to this setting.
❖
Setting animation display
Set whether to display in animation for screen or items.
From the Applications menu, [Settings]
1
[Screen]→[Animation]
[No animations]/[Some animations]/[All
2
animations]
❖
Setting font
Change displayed font on the screen.
From the Applications menu, [Settings]
1
[Screen]→[Font settings]
Select a font→[OK]
2
❖
Timeout
Set time before turning to sleep mode.
From the Applications menu, [Settings]
1
→
[Screen]→[Timeout]→Select a time
→
→
→
→
58
Settings
Applications
◆
Permitting to install unknown
sources applications
Permit to install applications obtained from sites, mails,
etc. other than Android market.
･
To protect the terminal and personal data, only
download applications from trusted sources such as
Android Market.
From the Applications menu, [Settings]
1
[Applications]→Mark [Unknown sources]
Confirm precautions and [OK]
❖
Displaying downloaded files
Display a list of downloaded files (applications, images,
document, etc.).
In the Applications menu, [Browser]
1
[Downloads]
✔
INFORMATION
･
Applications downloaded from Android Market are not
displayed.
◆
Viewing permitted operation of the
applications in the terminal
From the Applications menu, [Settings]
1
[Applications]→[Manage applications]
･
Tap [Sort by size]/[Sort by name] to sort
applications.
Select an application
2
･
If all permitted operations do not appear, tap [All].
→
→→
→
◆
Deleting application data or cache
From the Applications menu, [Settings]
1
[Applications]→[Manage applications]
･
Tap [Sort by size]/[Sort by name] to sort
applications.
Select an application→[Clear data]/[Clear
2
cache]
･
For [Clear data], tap [OK].
◆
Uninstalling applications
･
It is recommended to uninstall the applications that are
→
obtained from Android Market from the Android Market
screen.→P85
･
You cannot uninstall some pre-installed applications by
default. And if pre-installed applications are unistalled,
you can reset the terminal to restore.
From the Applications menu, [Settings]
1
[Applications]→[Manage applications]
･
Tap [Sort by size]/[Sort by name] to sort
applications.
Select an application→[Uninstall]→[OK]
2
[OK]
◆
Displaying running services
From the Applications menu, [Settings]
1
[Applications]→[Running services]→Select
a service name
→
Perform operations
→
→
→
→
59
Settings
◆
Checking storage use
From the Applications menu, [Settings]
1
[Applications]→[Storage use]
･
Tap [Sort by size]/[Sort by name] to sort
applications.
◆
Using application development
function
From the Applications menu, [Settings]
1
[Applications]→[Development]
･
To use USB debug function, install USB driver to a
PC. For details, refer to the information about this
product in the following site.
http://www.fmworld.net/product/phone/sp/android/
develop/
･
For functions for software developer such as USB
debug or mock location, refer to the following
website.
http://developer.android.com/
❖
Setting not to turn off the screen
during charge
From the Applications menu, [Settings]
1
[Applications]→[Development]→Mark
[Stay awake]
Accounts & sync
→
◆
Adding accounts
From the Applications menu, [Settings]
1
[Accounts & sync]
[Add account]→Select a type of account
2
→
→
Set required items
Setting account : Select an account→Set required
items
✔
INFORMATION
･
Multiple Google accounts can be added on the terminal.
･
Register the Google account set for logging into Picasa
web album as the Google account for the terminal. After
you have registered a Google account for the terminal
and then entered that Google account to acquire a new
Picasa account web album, Picasa will not be displayed
as the synchronization item of the Google account for the
terminal.
◆
Removing accounts
From the Applications menu, [Settings]
1
[Accounts & sync]→Select an account
[Remove account]→[Remove account]
✔
INFORMATION
･
The Google account you set first cannot be removed in
this operation. To remove the first set Google account,
reset the terminal.
･
docomo account cannot be removed.
→
P61
→
→
→
→
60
Settings
◆
Setting automatically synchronized
Google applications
You can set automatic synchronization for the terminal
and Google online service contacts, calendar, Gmail, etc.
From the Applications menu, [Settings]
1
[Accounts & sync]→Mark [Background
→
Mark [Auto-sync]→Select an
data]
account in Manage accounts list
item
✔
INFORMATION
･
When [Background data] is marked, automatic data
communications by all applications installed to the
terminal will be allowed. Furthermore, if the [Auto-sync]
is marked, automatic synchronization of data by
applications will be allowed.
◆
Starting synchronization manually
From the Applications menu, [Settings]
1
[Accounts & sync]→Select an account
❖
Canceling synchronization
During synchronization,
1
→
Set each
→
→
→
Privacy
◆
Back up my data & Automatic
restore
Using Google server, you can back up/restore data.
From the Applications menu, [Settings]
1
[Privacy]
[Back up my data]/[Automatic restore]
2
Back up my data :
･
Images, music, etc. cannot be saved.
Automatic restore :
reinstalling application.
◆
Resetting the terminal
All data (except electronic dictionary) is erased from the
internal storage. All installed applications and saved data
to the terminal are deleted.
From the Applications menu, [Settings]
1
[Privacy]→[Factory data reset]→Mark
[Erase built-in storage]
･
When the screen lock is set, enter the screen unlock
pattern or security code/password.
[Erase everything]
2
A short while after the reset is completed, the terminal
will be restarted.
✔
INFORMATION
･
When the touch panel does not work properly, turn the
power off and on.
Save application data and settings.
Restore backed up data when
→
[Reset phone]
→
→
61
Settings
Storage Searching the terminal or
sites
◆
Checking the memory space
You can check memory space of the terminal, microSD
card and mass-storage device connected with USB.
From the Applications menu, [Settings]
1
[Storage]
◆
Erasing data in microSD card
･
Note that this operation erases all data in the microSD
card.
From the Applications menu, [Settings]
1
[Storage]→[Unmount SD card]
･
When precautions about unmount SD card appear,
Tap [OK].
[Erase SD card]→[Erase SD card]
2
･
When the screen lock is set, enter the screen unlock
pattern/security code/password.
[Erase everything]
3
You can search function in the terminal or web pages.
Voice search is also available.
<Example> Entering a keyword to search
→
→
From the Home screen,
1
Enter a keyword
2
Search suggestions appear according to the character
entry.
Voice search : →Speak a keyword to microphone.
･
You can use voice search from the Home screen (
P29) and applications (→P30).
Select a search suggestion
3
◆
Search settings
Make search settings.
From the Home screen,
1
[Search settings]→Set each item
Searchable items :
to be searched.
Google search :
Google.
Specify the function in the terminal
Delete shortcuts or set sharing with
→
→→
62
Settings
High-performance unified search
Enter a keyword to search directly web search engines for
shopping, gourmet, etc.
From the Applications menu, [High-
1
performance unified search]
･
For first activation, a confirmation screen of "Terms
of use" appears. After confirmation, tap [I agree].
Enter a keyword →Select a search site
2
✔
INFORMATION
･
When High-performance unified search information is
refreshed, appears on the status bar.
◆
Managing search sites
From the Applications menu, [High-
1
performance unified search]
Perform target operations
2
Setting the default search site : Select a search site (1
sec. or more)→Drag the site to the top of the
search sites list
Adding search sites : [＋]→Mark a search site→[OK]
Language & input
･
For ATOK, see "Setting ATOK".→P38
◆
Switching to English display
Change the language to be used to English.
From the Applications menu, [設定
1
(Settings)]
input)]
✔
INFORMATION
･
Some applications are not displayed in English.
･
To change to the Japanese display, operate as follows.
From the Applications menu, [Settings]
input]
◆
Registering to the user dictionary
From the Applications menu, [Settings]
1
[Language & input]→[User dictionary]
2
→[言語と入力
→
[Select locale]→[English]
→[言語を選択]→[日本語
→
Enter a word→[OK]
(Language &
→
[Language &
]
→
63
Settings
◆
Voice input & output
❖
Setting voice recognizer
Setting Google voice search
From the Applications menu, [Settings]
1
[Language & input]→[Voice recognizer
→
settings]
Language :
SafeSeach :
Block offensive words :
❖
Text-to-speech
You can set the read out speed and language.
From the Applications menu, [Settings]
1
[Language & input]→[Text-to-speech
settings]
Set each item
2
Speach rate :
Language :
･
･
Set each item
Set language for Google voice search.
Set adult filter for images and text.
improper search results
Set the voice unique to the language used
for reading out text.
To play back a sample voice, tap [Listen to an
example].
To enable the settings of application or functions
supporting text-to-s peech at all times, mark [Always
use my settings].
Set whether to display
Set the text read out speed.
◆
Setting the keyboard
❖
Input method option
Set whether to display input method option when
entering characters.
→
→
From the Applications menu, [Settings]
1
[Language & input]→[Input method
selector]
Selecting an item
2
Automatic :
(keyboard) can be selected
Always show :
input methods (keyboard)
Always hide :
methods (keyboard)
❖
Setting the Android keyboard
Set key operation tone of the Android keyboard, text edit
suggestion display, etc.
From the Applications menu, [Settings]
1
[Language & input]→[Configure input
methods]
[Settings]
Show when multiple input methods
Show regardless of the number of
Hide regardless of the number of input
→
In the [Android keyboard] field,
→
Set each item
→
→
64
Settings
Accessibility Date & time
Enable the accessibility which respond to user operations
with sound and vibration or read out text.
･
By default, accessibility application are not registered.
You can obtain accessibility application (SoundBack,
KickBack, TalkBack, etc.) and install to the terminal to
set.
From the Applications menu, [Settings]
1
[Accessibility]→Set each item
Accessibility :
accessibility in [Accessibility] to be valid/invalid.
Accessibility services :
downloaded application (TalkBack etc.) to collect all
text entered on the terminal.
Accessibility scripts :
application to download accessibility scripts from
Google in [Download accessibility scripts].
Touchscreen gestures :
interpretered as touch and hold in [Touch & hold
delay].
Set application supporting the
Set to permit/not to permit
Set to permit/not to permit
Set delay time until a touch is
→
Make settings about date and time or their display.
From the Applications menu, [Settings]
1
[Date & time]→Set each item
･
Unmark [Automatic date & time] and [Automatic
time zone], to set date, time, and time zone
manually.
→
65
Settings
About phone
Display various information about the terminal.
From the Applications menu, [Settings]
1
[About phone]→Check each item
Software Update :
P106
Profile :
Status :
name and address, IMEI (individual serial number),
etc.
Battery use :
Legal information :
authentication logo.
Model number/Android version/Baseband version/
Kernel version/Build number :
or number.
Update software to latest one.
Set and check profile
Check battery level, phone number, network
Check battery usage.
Check Terms of use or
Check each version
→
→
66
Settings
Mail/Internet
sp-mode mail
You can send and receive mail using i-mode mail address
(@docomo.ne.jp).
Pictograms and deco-mail can be used, and automatic
reception also is supported.
･
For details on sp-mode mail, refer to “
ク
(sp
モード編
(in Japanese only).
1
) Mobile Phone User's Guide [sp-mode]”
From the Applications menu, [sp
ル
(sp-mode mail)]
From here on, follow the onscreen instructions.
SMS
You can send and receive text messages up to 70 twobyte characters long (up to 160 one-byte characters for
only alphanumerics) addressed to a mobile phone
number.
◆
Composing and sending SMS
From the Applications menu, [Messaging]
1
[New message]
[To]→Enter a mobile phone number
2
[Type to compose]→Enter a message
3
[Send]
ご利用ガイドブッ
モードメー
→
→
✔
INFORMATION
･
SMS can be also sent to or received from the parties
using overseas network operators. For countries and
overseas network operators available, refer to "Mobile
Phone User's Guide [International Services]" or
DOCOMO International Services website.
･
To send to users of overseas network operators, enter
"+", "Country code" and then "the recipient mobile phone
number". You can also enter "010", "Country code" and
"the recipient mobile phone number" to send messages.
(To reply to the received SMS overseas, enter "010" .)
Enter the phone number without a leading "0", if any.
･
To set SMS reception report, from the Applications
menu, [Messaging]
reports].
◆
When SMS is received
When SMS is received, the notification icon appears on the
status bar. Open the Notification panel to check new SMS.
✔
INFORMATION
･
You cannot check for any SMS in the SMS center from
the terminal.
･
If the terminal is initialized and an SMS is received right
after rebooting, ringtone and vibrator may not work
regardless of notification settings for new SMS.
･
SMS cannot be received when the terminal is low on
memory. Delete unnecessary applications to obtain
memory space.
◆
Displaying received SMS
From the Applications menu, [Messaging]
1
Select a message thread
2
→→
[Settings]→Mark [Delivery
→
P59, 85
67
Mail/Internet
◆
Replying to SMS
From the Applications menu, [Messaging]
1
Select a message thread→[Type to
2
compose]
◆
Forwarding SMS
From the Applications menu, [Messaging]
1
Select a message thread→Select an SMS (1
2
sec. or more)
[To]→Enter a mobile phone number
3
[Send]
◆
Deleting SMS
<Example> Deleting an SMS
From the Applications menu, [Messaging]
1
Select a message thread→Select an SMS (1
2
sec. or more)
Deleting message thread : Select a message thread (1
Deleting all message threads : →[Delete all
[Delete]
3
◆
Setting SMS auto delete
From the Applications menu, [Messaging]
1
Mark [Delete old messages]→[Text
2
message limit]
Enter a message limit→[Set]
3
→
Enter a message→[Send]
→
[Forward]
→
[Delete message]
sec. or more)→[Delete thread]
threads]
→
[Settings]
✔
INFORMATION
･
You can protect SMS from being deleted by the following
operation.
From the Applications menu, [Messaging]
message thread
message]
◆
Copying SMS from docomo mini
→
Select an SMS (1 sec. or more)→[Lock
→
Select a
UIM card
You can copy SMS saved on docomo mini UIM card of
another terminal to the terminal.
･
SMS in the terminal cannot be copied to the docomo
→
mini UIM card.
From the Applications menu, [Messaging]
1
→
[Settings]→[Manage SIM card
messages]
Select SMS (1 sec. or more)→[Copy to
2
device memory]
･
To delete SMS, select SMS (1 sec. or more)→Tap
[Delete]→[OK].
✔
INFORMATION
･
To reply or forward from SMS on docomo mini UIM card,
copy it to the terminal in advance.
◆
Setting new SMS notification
From the Applications menu, [Messaging]
1
[Settings]
→
→
Set each item
2
Notifications
Select ringtone
Vibrate
: Set whether to notify you that there is
new SMS by notification icon on the status bar.
new SMS.
vibration.
: Set the ringtone for notifying you of
: Set whether to notify you of new SMS by
→
→
68
Mail/Internet
Set mail accounts provided by mopera U or general
providers to use Email.
◆
Setting mopera U mail account
Set mopera U account to use mopera U mail.
･
The mailbox capacity of mopera U mail is approximately
50 Mbytes. Each mail can be sent or received with an
attachment of up to about 5 Mbytes.
■
Using a POP server
From the Applications menu, [Email]
1
[Email address]→Enter the mopera U mail
2
address
→
password
[Username]→Enter mopera U user ID
3
[Password]→Enter mopera U password
[POP3 server]→Enter "mail.mopera.net"
[Security type]→Select a security
4
Check entered settings→[Next]
5
[SMTP server]→Enter "mail.mopera.net"
6
Check the entered mopera U user name and
password
In the option settings screen, set the email
7
check [Inbox check frequency], etc.
On the mail account registration screen,
8
[Your name]
[Password]→Enter mopera U
→
[Manual setup]→[POP3]
→
[Next]
→
→
Enter your name→[Next]
[Next]
◆
Setting up a general provider mail
account
･
Obtain the information required for setting up the mail
account from your service provider in advance.
From the Applications menu, [Email]
1
[Email address]→Enter a mail address
2
[Password]→Enter a password→[Next]
From here on, follow the onscreen instructions.
✔
INFORMATION
･
If automatic setting of the mail account does not
complete, tap [Manual setup] in Step 2, and manually
enter the account settings.
･
With some service providers, settings for "OP25B
(Outbound Port 25 Blocking): spam mail transmission
blocking" are needed. For details, contact the service
provider you are subscribed to.
･
→
If you have already set a mail account and want to add on
another mail account, on the mail list, tap
→
settings]
→
[Add account]
→
→
[Account
→
69
Mail/Internet
◆
Setting reception for each mail
account
❖
Setting automatic checking of new
email
From the Applications menu, [Email]
1
･
If you have several mail accounts, tap a mail
account at the top left of the screen to switch.
→
[Account settings]→[Inbox check
2
frequency]
✔
INFORMATION
･
When you set to connect to the mail server at regular
intervals and if you use the pay-as-you-go plan data
communication, charges will be incurred each time new
mail is checked.
❖
Setting new mail notification
From the Applications menu, [Email]
1
･
2
Set each item
3
Email notifications :
Select ringtone :
Vibrate :
→
Select check frequency
If you have several mail accounts, tap a mail
account at the top left of the screen to switch.
→
[Account settings]
there is new email by notification icon on the status
bar.
new email.
vibration.
Set whether to notify you that
Set the ringtone for notifying you of
Set whether to notify you of new email by
◆
Composing and sending email
From the Applications menu, [Email]
1
･
If you have several mail accounts, tap a mail
account at the top left of the screen to switch.
2
[To]→Enter an address
3
･
To add a Cc or Bcc, Tap [Add Cc/Bcc].
[Subject]→Enter a subject
4
[Compose Mail]→Enter a message
5
･
To attach a file, →Select a file.
[Send]
6
✔
INFORMATION
･
Email is handled as email from a PC. If the r eceiver sets
rejection of emails from PCs, the email cannot be sent.
◆
Receiving/Displaying emails
From the Applications menu, [Email]
1
･
If you have several mail accounts, tap a mail
account at the top left of the screen to switch.
･
If you tap an account and [Combined inbox], an
inbox containing a mixture of emails for all mail
accounts is displayed. Each of the mail accounts is
distinguished by a color bar to the right of emails.
To refresh the inbox,
2
Select an email
3
✔
INFORMATION
･
If Inbox check frequency (→P70) and Email notifications
in Account settings (
appears on the status bar. Open the Notification panel
and tap the notification to display the inbox.
→
P70) are set, notification icon
70
Mail/Internet
◆
Replying to an email
Display an email→ / →[Compose
1
→
Enter a message→[Send]
Mail]
◆
Forwarding emails
Display an email
1
address
◆
Deleting emails
Display an email list→Check emails
1
→
[Send]
→→
[To]→Enter a mail
Gmail
Gmail is a Google online email service. You can send and
receive emails using Gmail on the terminal.
･
To use Gmail, you need to set up a Google account on
the terminal. If a Google account is not yet set, follow the
onscreen instructions that are displayed when Gmail is
activated for the first time.
◆
Opening Gmail
→
From the Applications menu, [Gmail]
1
A list of message threads is displayed in the inbox.
❖
Refreshing Gmail
In the inbox,
1
The inbox is refreshed with Gmail on the terminal and
Gmail on the website synchronized with each other.
･
For details on Gmail, perform the following
operation and refer to the mobile help.
In the Gmail inbox, →[Help]
71
Mail/Internet
Early warning "Area Mail"
This is a service with which you can receive emergency
earthquake flash report delivered by the Meteorological
Agency etc.
･
Area Mail is a free service and subscription is not
required.
･
Up to 50 Area Mails can be saved.
･
Area Mail cannot be received when the power off, in
Airplane mode, during international roaming, while
displaying PIN unlock screen, etc. When the terminal is
low on memory, Area Mail may not be received.
･
Area Mail that could not be received cannot be received
later.
◆
When early warning "Area Mail" is
received
When Area Mail is received, the buzzer alarm or the Area
Mail ringtone sounds and the notification icon appears on
the status bar.
･
The buzzer alarm or the Area Mail ringtone sounds in
maximum volume. The setting cannot be changed.
･
By default, the sound is emitted even in manner mode.
You can set to disable the sound.→P72
◆
Displaying received Area Mail
In the Applications menu, [Area Mail]
1
Select an Area Mail
→
◆
Early warning "Area Mail" setting
From the Applications menu, [Area Mail]
1
[Settings]
→
Set required items
2
Receive setting :
Beep tone :
whether it sounds in manner mode.
Check screen image and beep tone :
for receiving Area Mail
Other settings:
Mails other than Early Warning.
Set whether to receive Area Mails.
Set how long Area Mail sounds and
Check operations
Set to receive, store or delete Area
→
72
Mail/Internet
Google Talk Browser
Google Talk is an online instant message service provided
by Google. You can enjoy chat with Google members by
using Google Talk on the terminal.
･
To use Google Talk, you need to set up a Google account
on the terminal. If a Google account is not yet set, follow
the onscreen instructions that are displayed when
Google Talk is activated for the first time.
◆
Online chat
❖
Activating Google Talk
From the Applications menu, [Talk]→[Sign
1
in]
The Friends list is displayed.
･
For details on Google, perform the following
operation and refer to the mobile help.
In the Google Talk friends list, →[Help]
You can view web pages like on a PC using Browser.
On the terminal, Browser can be used over a packet
transmission or Wi-Fi connection.
◆
Operation while viewing website
■
Switching web page in portrait/landscape view
Hold the terminal vertically or horizontally to switch the
portrait/landscape view.
■
Zooming in/out on web page
You can zoom in/out on pages by the following operations.
Pinch-out/Pinch-in :
Double-tap :
･
To return to the view before it is zoomed in, double-tap
again.
■
Scroll/Pan
Scroll the screen up/down or left/right or pan in all
directions to display the desired part of the screen.
◆
Activating Browser to display a
Zoom in.
Zoom in/out.
website
From the Applications menu, [Browser]
1
Enter the URL/keyword in the address bar
2
Select /website
3
73
Mail/Internet
◆
Opening a new tab
･
You can open up to 16 tabs.
Display website
1
･
Website display mode→P73
→
[New tab]/[New incognito tab]
2
Switching : Select a tab
Closing : Select a tab
✔
INFORMATION
･
Alternatively, when a website is displayed, tap to
open a new tab.
◆
Displaying web pages from history
When a web page is displayed,
1
[History]
Select a history type
2
･
To display the history of frequently viewed web
pages, tap [Most visited].
Select a history of the web page
3
→
→
◆
Registering a bookmark to quickly
display a web page
❖
Registering a bookmark
When a web page is displayed,
1
A list of Bookmarks is displayed.
･
→
Tap [List]/[Thumbnails] to switch between list
view and thumbnail view.
[Add bookmark
2
[OK]
3
❖
Displaying web pages from
bookmarks
When a web page is displayed,
1
Select a bookmark
2
Editing : Select a bookmark (1 sec. or more)→[Edit
bookmark]→Set required items→[OK]
Deleting : Select a bookmark (1 sec. or more)
[Delete bookmark]→[OK]
◆
Changing web page display mode
❖
Changing text size
When a web page is displayed,
1
[Settings]→[Advanced]→[Text size]
Select a text size
❖
Changing the default zoom
You can set the magnification ratio for displaying a web
page.
When a web page is displayed,
1
[Settings]→[Advanced]→[Default zoom]
Select magnification ratio
・・・
]
→
→
→
→
→
74
Mail/Internet
◆
Web page link operations
The following operations are possible when a link
displayed on a web page is tapped.
URL
･
Tap :
Open web page.
･
Touch and hold for 1 second or more :
Email address
･
Tap :
Compose email.
･
Touch and hold for 1 sec. or more :
Phone number
･
Touch and hold for 1 second or more :
phone number to Contacts.
File
･
Tap :
View/Save a file.
･
Touch and hold for 1 second or more :
✔
INFORMATION
･
Saved files can be checked in Document Viewer or the list
of downloaded files.
◆
Saving images displayed on a web
Copy URL.
Copy email address.
Add/Copy a
Save a file.
page
When a web page is displayed, select an
1
image (1 sec. or more)
･
Saved images can be checked in Gallery (→P81) or
the list of downloaded files.
◆
Setting a home page
You can set the home page that is displayed when Browser
is activated or a new tab is opened.
When a web page is displayed,
1
[Settings]→[General]→[Set homepage]
Enter a URL→[OK]
→
[Save image]
→
→
◆
Clearing history or cache
When a web page is displayed,
1
[Settings]→[Privacy & security]→[Clear
→
cache]/[Clear history]/[Clear all cookie
data]/[Clear form data]/[Clear location
access]/[Clear passwords]
◆
Setting security
When a web page is displayed,
1
[Settings]→[Privacy & security]/[Advanced]
→
Set required items
Show security warnings :
is detected when this item is marked, a warning is
displayed. To protect security, we recommend not
unmarking this item.
Accept cookies :
saving and reading of cookies can increase security
level.
Remember passwords :
disable saving of user names and passwords for
sites that were entered during browsing of web
pages can increase security level.
Enable JavaScript :
security level.
Enable plug-ins :
prohibits use of Browser's extended functions and
can increase security level.
✔
INFORMATION
･
Some web services might no longer be available if
cookies are prohibited.
Unmarking this item to prohibit
Unmarking this item can increase
Setting [On demand] or [Off]
→
[OK]
→
If a problem in site security
Unmarking this item to
75
Mail/Internet
File management
Bluetooth communication
You can connect the terminal and a Bluetooth device to
perform wireless communication or play back a voice
sound or music.
･
Note that using Bluetooth connection makes battery
consumption faster.
･
Wireless communication is not guaranteed for all
Bluetooth devices.
✔
INFORMATION
･
For information on compatible Bluetooth version,
profiles, etc., see "Main specifications".
･
1Seg sound can be only played back with A2DP
compatible Bluetooth device that supports SCMS-T
content protection method.
･
For operations of the Bluetooth device, refer to the
operation manual of your Bluetooth device.
❖
Handling precautions when using
Bluetooth function
･
Connect with another Bluetooth device keeping the lineof-sight distance to 10 m or shorter. Distance available
for connection may be shorter if obstacles exist between
the terminal and the Bluetooth device or depending on
surrounding (wall, furniture, etc.).
･
Place a Bluetooth device as far as possible from other
electric appliances, audio visual devices and office
appliances. A microwave oven strongly affects the
connection when it is operated. Connection may not be
established correctly when other devices are powered
on, or the connection may cause noises on TV or radio
or reception difficulty.
･
Under strong ambient signals, connection may not be
established.
→
P109
･
Radio waves emitted by a Bluetooth device may affect
electronic medical equipment. Turn off the terminal and
other Bluetooth devices in a train, aircraft or hospital,
near an automatic door or fire alarm, and at a place
where flammable gases are generated such as a gas
station. Otherwise, under certain circumstances, an
accident may result.
❖
Radio wave interference with wireless
LAN
Because a Bluetooth device and wireless LAN
(IEEE802.11b/g/n) use the same frequency band (2.4 GHz),
if the device is used near a device with wireless LAN
capability, radio wave interference may occur, and
communication speed may be reduced, noise may occur,
or connection may not be established. In this case, turn the
wireless LAN device power off, or move the terminal and
the Bluetooth device away at least 10 m from the wireless
LAN device.
◆
Bluetooth function ON/OFF
Set Bluetooth to ON to use Bluetooth function. When you
do not use Bluetooth, set it to OFF in order to cut the
battery power consumption.
･
Turning the power OFF does not change Bluetooth ON/
OFF setting.
From the Applications menu, [Settings]
1
[Wireless & networks]
Mark [Bluetooth]
2
When activated, appears on the status bar.
Bluetooth function OFF : Unmark [Bluetooth]
･
You can also set Bluetooth to ON/OFF by the setting
panel.→P28
76
File management
→
◆
Connecting with registered
Bluetooth devices
Connect Bluetooth device. You can listen to the music
using a Bluetooth device, or exchange data to or from a
Bluetooth device.
･
Set a Bluetooth device to connection stand-by mode in
advance.
From the Applications menu, [Settings]
1
[Wireless & networks]
Mark [Bluetooth]→[Bluetooth settings]
2
[Find nearby devices]
･
To search the device again, tap [Scan for devices].
Tap a Bluetooth detected→Enter a passkey
3
(PIN) if necessary, [OK]/[Pair]
■
When connection is requested from another
Bluetooth device
If a Bluetooth pair setting request screen appears, enter a
passkey (PIN) if necessary and tap [OK], or tap [Pair].
✔
INFORMATION
･
Tapping at the right of a Bluetooth device paired
from Bluetooth settings allows you to change device
name, unpair, and select connection type.
･
If the terminal is not detected from the Bluetooth device,
mark [Discoverable] in Bluetooth settings. Unmark to
cancel detectable status.
◆
Sending or receiving data to or from
→
→
Bluetooth device
You can send data such as Gallery (→P81) and contacts or
receive the data via Bluetooth communication.
<Example> Sending files in Gallery
Open Gallery to select an image (1 sec. or
1
more)
→
[Bluetooth]
2
･
When Bluetooth function is OFF, tap [Turn on] on
the confirmation screen.
Tap a Bluetooth device
3
Open the Notification panel to check if transmission is
completed.
<Example> Receiving files from a Blutooth device
Send files from a Bluetooth device
1
･
If the terminal is not detected from the Bluetooth
device, mark [Discoverable] in Bluetooth settings.
After file arrival is notified, open the
2
Notification panel
Incoming file]
A received file can be checked from the notification
panel or [Show received files] in Bluetooth settings.
◆
Canceling connection with a
→
[Bluetooth share:
→
[Accept]
Bluetooth device
From the Applications menu, [Settings]
1
[Wireless & networks]→[Bluetooth
settings]
Tap a Bluetooth device→[OK]
2
◆
Changing terminal name for
Bluetooth communication
From the Applications menu, [Settings]
1
[Wireless & networks]→Mark [Bluetooth]
[Bluetooth settings]
[Device name]→Enter the terminal name
2
[OK]
→
→
→
→
77
File management
Connecting an external device
◆
Operating data on microSD card
from a PC
When the terminal and a PC are connected by the included
PC connection USB cable T01, the microSD card in the
terminal is recognized as a removable disk by the PC, and
data on the microSD card can be operated from the PC.
･
Supported PC operating systems (OS) are "Microsoft
Windows XP", "Microsoft Windows Vista" and
"Microsoft Windows 7".
･
When an application that uses the microSD card is
running on the terminal, close the application before
mounting the microSD card on the PC.
Connect the terminal and a PC with the USB
1
cable
→
[USB connected]→[Turn on USB
2
storage]
･
When the precaution [Turn on USB storage]
appears, tap [OK].
Display the removal disk on a PC
3
Drag-and-drop files between the microSD
4
card and the PC
✔
INFORMATION
･
When the microSD card is mounted on the PC,
applications such as Camera that use the microSD card
cannot be used.
❖
Safely disconnecting the USB cable
･
Do not disconnect the USB cable during data transfer.
Doing so may damage or destroy the data.
Perform safely disconnecting the hardware
1
operation on the PC
[Turn off USB storage]→Disconnect the
2
USB cable
◆
Exchanging data to or from USB
mass storage
You can exchange data between the terminal and a USB
memory or an external hard disk drive connected via USB
with USB cable for external device connection T01
(optional).
Connect the terminal and a USB mass
1
storage with the USB cable
･
The USB mass storage is automatically mounted
(only 1 device when two or more are connected).
Perform required operations
2
✔
INFORMATION
･
For a USB mass storage with AC adapter, connect the AC
adapter. Otherwise, the storage is not recognized.
❖
Removing USB mass storage
･
Do not disconnect the USB cable during data transfer.
Doing so may damage or destroy the data.
From the Applications menu, [Settings]
1
[Storage]→[Unmount USB storage]
Disconnect the USB cable
→
→
78
File management
Applications
Camera
◆
Cautions on shooting
･
Although the camera is manufactured using extremely
high-precision technology, it may contain dots or lines
that are always lit or that do not light. When shooting
under low light conditions, in particular, white lines or
random color dots are likely to appear as noises. This is
not a malfunction.
･
When activating the camera, white stripes may appear
on the screen. This is not a malfunction.
･
The captured images may be different from actual
objects for color and brightness.
･
If you try to shoot an intense light source directly like the
sun etc., the images may be dark or noisy.
･
Fingerprints or body oil on the lens can affect images.
Wipe with a soft cloth before shooting.
･
The battery consumption is faster when using the
camera.
･
Shutter sound is emitted regardless of setting of Manner
mode.
Copyrights and portrait rights
Avoid reproducing, altering, or editing taken or
recorded pictures or sounds using the terminal
without the copyright holders authorization, because,
except for personal use etc., they are prohibited by the
Copyright law. Avoid using or altering pictures of
others without their consent, because they may
infringe on portrait rights.
Note that taking photos or recordings at some
demonstrations, performances or exhibitions may be
prohibited even when only for personal use.
Take care not to infringe on privacy when
shooting or sending images with the mobile
phone equipped with camera.
If you cause the public any trouble using the terminal,
you may be punished under law or regulations (for
example, nuisance prevention ordinance).
79
Applications
◆
Viewing shooting screen
a
Camera (still image) shooting screen
a
Video camera (recording) shooting screen
a
View/Play last saved still image/video
b
Setting icon
c
Shutter button
d
Switch between in-camera and out-camera
e
Switch between camera (photo) and video (recording)
f
Start recording/End recording buttons
◆
Shooting photo (camera)
From the Applications menu, [Camera]
1
Display an object on the shooting screen
Shutter sound is heard and a photo is shot.
◆
Recording video
From the Applications menu, [Camera]
1
b
c
d
e
b
f
d
e
→
Slide toward →Display an
object on the shooting screen
Sooting start sound is heard and a shooting is started.
･
When the shooting is started, a recording time is
displayed at the upper right of the shooting screen.
2
Sooting end sound is heard and a shooting is finished.
◆
Changing the shooting settings
･
Some items cannot be selected depending on the
combinations.
❖
Changing the settings for Camera
shooting (still image)
■
White balance (out-camera only)
Adjust coloring to match the surrounding light source.
■
Switch data save destination
Select a data save location.
■
Camera settings
Store location:
information.
Focus mode (out-camera only) :
according to the object.
･
The object can be focused from approximately 8 cm to
infinity.
･
When [Auto]/[Macro] is set, touch the shutter button for
1 second or more to lock the focus. When the camera
→
comes into focus, the focus frame turns to green and the
confirmation sound is emitted.
Picture size :
images.
Picture quality:
shooting (still image).
Restore defaults:
Switch On/Off of recording location
Change focus mode
Specify the picture size for shooting still
Specify the picture quality for Camera
Initialize camera settings to the default.
80
→
→
Applications
❖
Changing the settings for Video
shooting (recording)
■
White balance (out-camera only)
Adjust coloring to match the surrounding light source.
■
Video quality
Specify the image size for Video shooting (recording).
■
Time lapse interval
Select time interval for time-lapse picture
■
Switch data save destination
Select a data save location.
Gallery
Display/play pictures (still images or moving pictures)
that were saved shooting with the camera or
downloading.
･
The following file types of data can be displayed/played.
Still image : JPEG, BMP, GIF, PNG
Moving picture : H.263, H.264, H.264 AVC, MPEG-4, VC-
1, VP8, WMV9
◆
View/Play pictures
From the Applications menu, [Gallery]
1
Select an album→Select an image
･
appears for moving pictures in the image list
screen. Select an application to play.
･
Flick the screen left and right to switch between the
previous and next screen.
■
Operation while viewing a still image
･
Pinch-in/pinch-out to zoom out/in.
■
Operation while playing moving pictures
･
ty
･
Tap the screen to display keys or progress bar. You can
play/pause/rewind/fast forward with them.
adjusts volume.
→
■
Operation in the image list screen
･
Touch and hold an image for 1 second or more to
change the color of the image frame. The image is
selected. Tap the image to cancel selection.
･
When you select an image/images, tap [XX item(s)
selected]→[Select All]/[Deselect All] at the top of the
screen to select/cancel all images.
✔
INFORMATION
･
Tap [By album]/[Images and videos] at the top of the
screen to change the classification of the picture.
･
Tap the icon displayed in the upper screen to perform the
following operations.
: Activate the camera
: Display detail information
: Slideshow
: Select a sending method to send or share image
: Delete an image
：
Use an image (In the album list, it is used with off-
line)
Music player
You can play back music saved on the microSD card using
a music player.
･
For details on how to forward music files to the microSD
card from a PC, see "Operating data on a microSD card
from a PC".→P78
･
File format/codec that can be played back are as follows.
However, some files may not be played back.
WMA9, AAC, MP3, MIDI
81
Applications
◆
Playing music
From the Applications menu, [Music]
1
[New and recent]→Select an item
･
When you tap [Songs], go to Step 3.
Select an item
2
Select a song
3
❖
Operations in the playback screen
a
b
c
d h
a
Jacket image
b
[Songs]/[Artists]/[Albums]
･
Tap a song to add to playlist
･
Touch and hold for 1 second or more to search
related content
c
Slide to specify the playback position
d
Shuffle ON/OFF
e
Tap within 2 seconds in play time to jump to the
previous song/Tap after a lapse of 2 seconds in play
time to jump to the beginning of the song/Touch and
hold for 1 second or more to rewind
f
Pause/Playback
g
Jump to the next song/Touch and hold 1 second or
more to fast forward
h
Repeating all songs/Repeating current song/
Repeating off
ty
: Adjust volume
e-g
→
◆
Creating playlists
In the songs list screen, →[Add to
1
❖
1
❖
1
❖
1
◆
1
2
→
playlist]
name
[New playlist ...]→Enter a playlist
→
[OK]
Adding songs to a playlist
In the songs list screen, →[Add to
playlist]
→
Select a playlist
Sorting songs in playlist
In the playlists screen in the playback list,
select a playlist
to a destination
→
Drag of a song to move
Removing songs from a playlist
In the playlists screen in the playback list,
select the playlist
from playlist]
→
of a song→[Remove
Searching related content
In the songs list screen, →[Search]
[F media2U]/[YouTube]/[Browser]/[Music]
The content is searched in the media you specified.
82
Applications
Stereo earphones
YouTube
Attach the stereo earphones to the terminal so that you
can listen to the playback sound of videos and music on
earphones.
･
Setting MIC input→P57
Insert the plug of the stereo earphones
1
(optional) into the stereo earphone jack on
the terminal
Stereo earphone jack
Stereo earphone plug
YouTube is a Google online video streaming service. You
can play, search and upload videos to this service.
From the Applications menu, [YouTube]
1
The video list screen appears.
･
→
Tap [Sign in] to upload videos, create
favorites, playlists, etc.
･
To sign in YouTube, you need to set up a Google
account on the terminal. If a Google account is not
yet set, follow the onscreen instructions that are
displayed when signing in for the first time.
Select a video
2
･
Tap the playback screen to switch between pause
and playback.
･
Use
ty
･
Double-tap the playback screen to enlarge to full
screen in the landscape view.
✔
INFORMATION
･
Moving picture files of several hundred MB or more
should be uploaded from the PC. Uploading may not be
possible from the terminal depending on the network
environment.
to adjust volume.
83
Applications
Android Market
With Android Market, you can directly access to useful
applications or fun games which you can download and
install on the terminal. You can also send feedback or
opinions about applications.
･
To use Android Market, you need to set up a Google
account on the terminal. If a Google account is not yet
set, follow the onscreen instructions that are displayed
when Android Market is activated for the first time.
From the Applications menu, [Market]
1
Android Market screen appears.
･
When Android Market is activated for the first time,
read the Android Market terms of service and tap
"Accept".
✔
INFORMATION
･
Be sure to check the security of application, then install it
at your own risk. The terminal may be infected with a
virus and the data may be damaged.
･
NTT DOCOMO is not liable for malfunctions, if any,
caused by the application you installed. In such case, the
repair is charged even during the warranty period.
･
NTT DOCOMO is not liable for any disadvantage brought
to you or any third party due to an application you
installed.
･
Some applications automatically connect to the internet
and perform communications. Note that packet
communications charged may be higher.
◆
Android Market Help
On the Android Market screen, →[Help]
1
◆
Searching and installing
applications
In the Android Market screen, search the
1
application
Select an application→Check price, general
2
assessment, user opinions, etc. in the
details screen
[DOWNLOAD] (for free applications)/[BUY]
3
(for paid applications)
･
For buying paid applications→P85
･
If the application needs to access the data or
functions of the terminal, functions to be used by
that application are indicated on the screen.
Be careful about installing applications that access
lot of functions or a significant amount of data.
Once you select "OK" in this screen, you are
responsible for the consequences of using this
application on the terminal. To agree to the terms of
use of this application, tap [OK].
Tap on the status bar→Tap a bar during
4
installation
Select the application being installed in the
5
list screen
･
✔
INFORMATION
･
The icon of the installed application appears in the
application menu.
･
Installed accessibility plug-ins can be enabled in the
accessibility service list screen.
→
To cancel the download, tap [Cancel].
When installation is completed, appears on the
status bar.
Check download progress
→
P65
84
Applications
◆
Buying applications
Buy charged applications before downloading them.
These applications can be used on a trial basis for
specified period of time. If you do not request a refund
within the specified period of time, your credit card will be
charged.
･
Payments for applications are once only. Charges are
not incurred for uninstalling or redownloading an
application once it has been downloaded.
In the Android Market screen, search for the
1
application
[BUY]
2
･
[Select payment method]→Select a
3
payment method
･
･
･
[Refund Policy], [Google Billing and Privacy
4
Policy]
→
Select an application
If the application needs to access the data or
functions of the terminal, functions to be used by
that application are indicated on the screen.
Be careful about installing applications that access
lot of functions or a significant amount of data.
Once you select [OK] in this screen, you are
responsible for the consequences of using this
application on the terminal. To agree to the terms of
use of this application, tap [OK].
→
When you buy applications for the first time, log
into the Google Checkout payment and billing
service. Google Checkout is a service provided by
Google, a fast, secure and useful way to buy
applications from the terminal. For details, in the
Android Market screen, →[Help]→Refer to
"Buying apps".
If you do not have a Google Checkout account,
follow the onscreen instructions to fill in the form.
Set screen lock to ensure the security of the
terminal since the Google Checkout PIN is stored on
the terminal.→P44
→
Read document
[OK]
Agree with the Google Checkout service
5
conditions, [Buy now]
When installation is completed, appears on the
status bar.
■
Requesting a refund
You can request a refund within specified period of the
purchase of the application if you are not satisfied with it.
The application is deleted, and you are not charged. Note
that you can request a refund only once for each
application. If you requested a refund for a purchased
application in the past and purchase the sample
application again, a second refund request will not be
available.
◆
Deleting applications downloaded
from Android Market
On the Android Market screen, select [My
1
apps]
Select an application
2
[Uninstall]
3
･
When [Uninstall & refund] is not displayed for
charged applications, this means that the free trial
period has ended.
85
Applications
docomo market
In the docomo market, you can quickly access DOCOMO
recommended sites and useful applications.
From the Applications menu, [docomo
1
market]
The browser is activated and docomo market is
displayed.
✔
INFORMATION
･
To use docomo market, Internet connection by packet
communication (LTE/3G/GPRS) or Wi-Fi is required.
･
For accessing docomo market or downloading
applications introduced in docomo market, a packet
communication charge is separately applied. Some
downloaded applications automatically perform packet
communications.
･
The introduced applications on docomo market include
charged ones.
･
NTT DOCOMO is not liable for any disadvantage caused
by introduced websites on docomo market or the
acquired information from the website.
･
And NTT DOCOMO is not liable for contents,
adequateness to purpose of use, reliability, etc. of
applications introduced on the docomo market.
･
Some applications that you perform installation may give
the terminal instability of the operation, or may send your
location information or personal information registered
to the terminal to outside via the Internet and the
information may be used improperly. Please thoroughly
check a provider and operation status of the application
etc. which you want to use beforehand and then use it.
･
The copyrights of materials (documents, photographs,
illustrations, animations, sounds, software, etc.) on this
Site are the possession of DOCOMO or other third parties
and are protected by the Copyright Act as well as other
laws and agreements. Excluding the extent of quotation
and reproduction for private use that is approved in the
Copyright Act, without the consent of the party owing the
copyright, the reproduction, adapting or public
transmission of copyrighted material is prohibited.
GPS/Navigation
You can use the GPS function on the terminal and a
compatible application to check your current location or
search for routes to your destination.
◆
Using the GPS function
･
Note that DOCOMO is not liable for any damages that
may occur as a result of irregularities in the GPS system.
･
Note that DOCOMO is not liable for pure economic loss
if you cannot confirm the positioning (communication)
result with the terminal because of failure, malfunction,
error or external factors such as power failure (including
battery exhaustion).
･
You cannot use the terminal as a navigation system for
aircraft, vehicles, persons, etc. For this reason, note that
DOCOMO is not liable for losses incurred by navigation
performed by using location information.
･
You cannot use the terminal as a high-accuracy
measurement GPS. Note that DOCOMO shall have no
liabilities whatsoever even if you suffer damage or loss
due to a deviation of the location information.
･
GPS is a service operated by the USA Department of
Defense, so the GPS radio wave condition may be
controlled (accuracy degraded, radio wave suspended,
etc.) for reasons of US national security.
･
Wireless communications products (mobile telephones,
data detectors, etc.) might interfere with satellite signals
and cause signal reception to become unstable.
･
The displayed map based on the acquired location
information (latitude and longitude information) may be
inaccurate because of the legal system in each country
and area.
86
Applications
■
Where radio waves are difficult to receive
Note that since GPS is using radio waves for satellites,
under the following conditions, radio waves might not be
able to be received or might be difficult to receive. Also, do
not cover the upper right of the terminal (GPS antenna is
equipped) with your hand during use.
･
Inside or immediately under a building
･
Inside a basement or tunnel, and below the ground or
water
･
Inside a bag or box
･
In buildings-clustered or residential area
･
Inside or under a thick covering of trees
･
Near a high-voltage cable
･
In a car, inside a train compartment
･
Bad weather such as heavy rain or snow
･
When there are obstructions (people or objects) near the
terminal
◆
Enabling the location information
service
❖
Using GPS function
From the Applications menu, [Settings]
1
[Location & security]→Mark [Use GPS
satellites]
✔
INFORMATION
･
To measure highly accurate location information, use
GPS in a good field of view.
･
Note that this function increases power consumption.
･
We recommend joint use with a current location search
via a wireless network.
❖
Turning on location position search
→
[Agree]
→
via a wireless network
Your current location can be found based on information
from a Wi-Fi connection or a mobile network base station.
From the Applications menu, [Settings]
1
[Location & security]→Mark [Use wireless
networks]
･
◆
Google Map
The Google Maps application lets you view your current
location, find other locations and calculate routes.
･
To use Google Map, a network connection via LTE/3G/
GPRS or Wi-Fi is required.
･
To measure your current location, enable the location
information service in advance.
･
Google Maps do not cover all countries and cities.
❖
Displaying the current location
From the Applications menu, [Maps]
1
･
･
❖
Street View
･
Street View does not cover some areas.
In the map screen, select a position (1 sec.
1
or more)
･
→
If [Use wireless networks] is marked, this is
regarded as your having agreed to the anonymous
collection of position data by Google's location
information service. Data collection is carried out
regardless of whether or not the application is
activated.
Scroll or pan the map to display a part you want to
view.
To zoom in or out the map, perform the following
operation.
Pinch out/Pinch in :
Double tap :
Tap with two fingers :
When Street view is operating, →Tap [Compass
mode] to activate Compass mode. The compass in
Street view shows the same direction as the
terminal's electronic compass.
[Agree]
Zooms in/out.
Zooms in.
Zooms out.
→
Tap a balloon→[Street view]
→
→
87
Applications
❖
Searching for a place
In the map screen, [Search Maps]→Enter a
1
keyword in the Search box
･
You can enter addresses, city names, business
types and institution names (for example, London
and art museum).
/Select a search option→Tap a balloon
2
on the map
･
If multiple results are found, select a red circle on
the map to display a balloon. You can tap [Result] to
display the list, and select desired location to view a
detailed information and options.
･
The options you can use vary depending on the
location.
❖
Displaying layers
You can add traffic information to the map or switch to
aerial photomap display.
In the map screen, →Select an item
1
･
Traffic information and routes are not available in
all locations.
❖
Directions
In the map screen,
1
[My Location]→Enter the place of departure
2
→
[End point: ]→Enter the destination
･
If you want to view the route from the current
location, blank the [My Location] field.
･
You can tap on the right of the entry field to
specify the current location, address in Contacts, or
location on the map.
Select means of transportation (Car/Public
3
transportation/Walk)
: Car : Public transportation : Walk
→
[Done]
･
When you select Car, tap to start to search
routes.
･
If several destinations or routes are found when you
search, select any of them.
✔
INFORMATION
･
From the Applications menu, tapping [Navigation] also
activates navigation application.
◆
Checking the friend's location by
Google Latitude
You and your friends can check where you are on the map.
･
To use Google Latitude, you need to set up a Google
account on the terminal. If a Google account is not yet
set, follow the onscreen instructions that are displayed
when Latitude is activated for the first time.
･
Location information cannot be automatically shared.
You need to join Latitude and invite a friend who gives
his or her location information, or to receive an
invitation from him or her.
❖
Joining Latitude
In the map screen, →[Join Latitude]
1
･
For details on Latitude, perform the following
operation and refer to the mobile help.
In the map screen, →[Help]→[Google Latitude]
✔
INFORMATION
･
Alternatively, you can activate Google Latitude by
tapping [Latitude] from the Applications menu.
88
Applications
◆
Places
You can quickly search for facilities, stores, etc. in the
vicinity of your current location.
From the Applications menu, [Places]
1
Select a facility or store you want to search
2
･
You can add facilities or stores (museums,
bookstores, etc.) not in the list by tapping "Add".
Select the target location
3
･
The options you can use vary depending on the location.
1Seg
1Seg is a terrestrial digital TV broadcasting service that
allows mobile devices to receive broadcasted data along
with images and sounds.
You can also acquire detailed program information,
participate in quiz programs, enjoy TV shopping, etc.
For details on “1Seg” service, refer to the following website.
The Association for Promotion of Digital Broadcasting
http://www.dpa.or.jp/
◆
Using 1Seg
･
1Seg is a service provided by TV broadcasting
enterprises (stations), etc. A communication fee for
receiving video picture and sound is not required.
Contact NHK for details on your NHK viewing fees.
･
There are 2 types of information displayed in the data
broadcasting area: "Data broadcasting" and "Data
broadcasting site".
"Data broadcasting" is displayed using airwave along
with images and sounds; while "Data broadcasting site"
is displayed by connecting to a site provided by TV
broadcasting enterprises (stations), etc., using
information of data broadcasting.
For viewing "Data broadcasting site", etc., packet
communication fees are charged.
Some sites require information fees.
◆
Airwaves
1Seg is one of the broadcast services and a different type
of radio waves (airwaves) from that of Xi service or FOMA
service is received. Therefore, regardless of whether you
are in or out of Xi service or FOMA service area, it cannot
be received where airwaves do not reach or during
broadcasting interruptions.
Also, even in a terrestrial digital TV broadcasting service
area, reception condition may be poor or reception may be
unavailable in the following places.
･
A place far from the tower that the airwaves are sent from
･
Mountain-ringed regions or a place between buildings
where airwaves are interrupted by geography or buildings
･
Tunnel, underground or far back from a building where
airwaves are weak or do not reach
･
Moving may improve the reception condition.
✔
INFORMATION
･
If you watch 1Seg for a long time while charging, the
battery life may be reduced.
◆
Activating 1Seg
From the Applications menu, [TV]
1
1Seg watching screen appears.
･
When you activate 1Seg for the first time, read the
terms of use, tap [
channel list corresponding to the watching area.
P92
✔
INFORMATION
･
The minimum battery power to start is 5 percent, the
minimum battery power to continue operating is 2
percent.
･
It may take a time to acquire image data or broadcasted
data when you activate 1Seg or change channels due to
characteristic of digital broadcasting.
･
Depending on the airwave condition, video images or
sounds may be interrupted or stopped.
89
同意する
(Accept)] and create a
Applications
→
❖
1Seg watching screen
a
b
c
a
TV image area
･
Tap in the full screen to display channel selection
buttons
･
Double-tap to switch full screen/watching screens
･
Touch and hold for 1 second or more to fix the screen
･
Slide left and right to switch channels.
b
Subtitle area
c
Channel, broadcast station name, program name
･
Tap to display program contents
d
Data broadcasting area
e
Operation buttons for data broadcasting
f
Tuning button
g
Channel switching button
･
Touch and hold for 1 second or more to perform the
channel search
When an unregistered broadcasting station is found,
tap →[設定 (Settings)]→[
チャンネル設定
(Add channel)]→[はい (Yes)]→[はい (Yes)] to add the
channel list.
h
Slide left to start recording/Slide right to end recording
ty
: Display a program guide
(Channel setting)]→[
: Adjust volume
hg
チャンネル
チャンネル追加
(Channel)]→[
◆
TVlink
For some data broadcasting programs, link information to
related websites (TVlink) is displayed. Save TVlinks to
d
display related websites.
e
❖
Saving TVlinks
f
Select an item that can be registered as a
1
TVlink in the data broadcast area.
･
Procedure to save TVlink varies by the program.
･
If TVlink connection destination is HTM contents
(Browser etc.), the TVlink contents cannot be
registered.
❖
Displaying TVlinks
On the 1Seg screen, →[TV
1
→
Select TVlink
Connect to the saved website.
❖
Deleting TVlinks
On the 1Seg screen, →[TV
1
Select a TVlink (1 sec. or more)→[削除
2
(Delete)]
→[はい
Deleting all TVlinks : →[
い
(Yes)]
(Yes)]
全件削除
リンク
(TVlink)]
リンク
(TVlink)]
(Delete all)]→[
は
90
Applications
◆
Recording 1Seg programs
You can record image, sound, subtitle and data
broadcasting you are watching and save on a microSD
card.
On the 1Seg screen, slide left to start
1
recording
･
On the 1Seg screen →P90
Slide right to end recording
2
✔
INFORMATION
･
Use a microSD card formatted on the F-01D in advance.
･
If the following occurs while recording, recording
automatically stops.
- The remaining memory of the microSD card i s 2 MB or
less.
- Remaining battery is 10 percent or less
- 6 hours elapses after the recording starts
･
Recorded TV programs are saved as copyrighted data. It
cannot be attached to mail.
･
Recording extremely short programs (within 10 seconds)
cannot be stopped.
･
Record programs in a place where airwave condition is
stable. A program may not be recorded in a place where
the reception condition is unstable.
･
Recording operations are not available in full screen
mode. Switch to the watching screen.
･
While recording, you cannot change channel.
･
If another application is started while recording,
recording may not performed normally.
･
Camera shooting (still image) or Video shooting
(recording) cannot be performed while recording a
program.
･
If you use data communication services while recording,
recording may not performed normally.
･
If you unmount microSD card or make a USB connection
to mount microSD card on a PC while recording,
recording may fail.
･
If you record a paid broadcast, copy-controlled program
or when you move to a different broadcast area,
recording may end halfway.
❖
Playing recorded video
On the 1Seg screen,
1
Select data
2
･
Tap the playback screen to display the playback
controller. Double-tap the playback screen to turn to
the full screen.
･
If playback ended halfway in the previous session,
playback resumes from where it left off.
ty
✔
INFORMATION
･
In the recorded list screen, tap data for 1 second or more
to play, change the title, protect/unprotect the data.
❖
Deleting data from the recorded list
On the 1Seg screen,
1
Select data (1 sec. or more)
2
[削除 (Delete)]→[はい (Yes)]
3
･
: Adjust volume
To delete all items, in the recorded list screen,
[
全件削除
(Delete all)]→[はい (Yes)]
→
91
Applications
◆
1Seg settings
On the 1Seg screen, →[設定 (Settings)]
1
[
全般設定
2
◆
Setting the channel
❖
Creating a channel list
1
(General settings)]/[
→
(Channel)]
字幕表示
subtitle.
字幕言語切替
subtitles are to be displayed in programs with
multiple subtitles.
主・副音声切替
between main audio and sub audio in programs
broadcast with sub audio.
音声切替
listened to in programs broadcast with multiple
sound.
左右音声切替
side is to be listened.
なめらかモード
use the function for smoothing images. Marking [
めらかモード
battery consumption and shortens the available
watching time.
チャンネル設定
channel"→P92
放送用メモリ初期化
Erase information, TV links, etc. recorded by data
broadcasts.
Set each item
(Display subtitle) :
(Switch subtitle language) :
(Switch Main/sub sound) :
(Switch sound) :
(Switch left/right sound) :
(Smooth mode) :
(Smooth mode)] checkbox increases
(Channel setting) :
(Initialize broadcast memory) :
On the 1Seg screen, →[設定 (Settings)]
[
チャンネル
(Channel setting)]
(Edit channel list)]
(Channel)]→[
→[チャンネルリスト編集
→[未設定
チャンネル
Set On/Off for displaying
Set which sound is to be
Set whether or not to
"Setting the
チャンネル設定
(Not set)] (1
sec. or more)
Set which
Switch
Set which
[作成 (Create)]→[
2
自動設定
手動設定
(Manual setting) :
な
to watch from the list of regions to create a channel
list.
自動設定
(Automatic setting) :
can be received in your location are automatically
scanned to create the channel list.
✔
INFORMATION
･
To reset the channel list, operate as follows.
On the 1Seg screen,
(Channel)]
→[チャンネル設定
ネルリスト初期化
❖
Switching channel lists
On the 1Seg screen, →[設定 (Settings)]
1
[
チャンネル
(Channel setting)]
(Switch channel list)]
❖
Deleting broadcasting stations from
手動設定
(Auto set up)]→Set a channel list
→[設定
(Channel setting)]→[
(Initialize channel list)]→[はい (Yes)]
(Channel)]→[
→[チャンネルリスト切替
→
the channel list
On the 1Seg screen, →[設定 (Settings)]
1
[
チャンネル
(Channel setting)]
(Channel)]→[
→[チャンネルリスト編集
(Edit channel list)]
Select a channel list
2
Select a broadcasting station (1 sec. or
3
more)
→
Deleting multiple channels : [
several)]→Mark broadcasting stations→[削除
(Delete)]
[はい (Yes)]
4
(Manual set up)]/[
Select the region you want
Broadcast stations that
(Settings)]→[
チャンネル
チャン
→
チャンネル設定
Select a channel list
→
チャンネル設定
複数削除
(Delete
92
Applications
❖
Changing channel button allocations
On the 1Seg screen, →[設定 (Settings)]
1
[
チャンネル
(Channel setting)]
(Edit channel list)]
Select a channel list→[
2
Drag to sort the list→[完了 (Done)]
3
◆
Playing digital terrestrial
(Channel)]→[
チャンネル設定
→[チャンネルリスト編集
並べ替え
(Sort)]
broadcasting program
You can watch digital terrestrial broadcasting programs
recorded in microSD card in high image quality (VGA
class) (Digital terrestrial broadcasting taking out).
･
The recorded program may not be played depending on
the recording device.
Recording a digital terrestrial broadcasting
1
program to microSD card
Insert a microSD card to the terminal
2
From the Applications menu, [TV]
3
Select a digital terrestrial broadcasting
4
program
✔
INFORMATION
･
To record a digital terrestrial broadcasting program to a
microSD card, use optional SD memory card conversion
adapter etc.
→
Link with DLNA compatible
→
device
Contents such as still images, moving pictures or music
saved in a microSD card in the terminal can be played back
on the DLNA compatible TV or PC. And the contents
stored in the DLNA compatible PC or network-attached
storage (NAS) can be played back on the terminal.
･
Wi-Fi network is required to link the DLNA compatible
device→P51
･
For operations of the DLNA compatible device, refer to
the operation manual of your DLNA compatible device.
･
Link is not guaranteed for all DLNA compatible devices.
◆
Activating DLNA server
Activate the DLNA server to allow access from the DLNA
compatible device.
From the Applications menu, [DiXiM
1
Server]
[DiXiM Server] is marked, and appears on the
status bar.
[
アクセス制御
2
アント機器の一覧
mark the DLNA compatible device to allow
access
Access to the terminal is allowed.
(Access control)]→In [
(List of client devices)],
クライ
93
Applications
◆
Playing back the terminal's
contents on the DLNA compatible
device
･
Activate the DLNA server to allow access from the DLNA
compatible device in advance.
From the Applications menu, [DiXiM Player]
1
→
Select the server name of the terminal in
the server list.
Operate on the DLNA compatible device
2
･
Access the DiXiM server of the terminal to play back
contents
✔
INFORMATION
･
Moving pictures taken with the camera may not be
played back with the DLNA compatible device other than
F-01D.
◆
Distributing contents in the
terminal
Distribute contents on the terminal to the DLNA
compatible device. Playback can be operated via the
terminal.
･
Activate the DLNA server to allow access from the DLNA
compatible device in advance. And, set the DLNA
compatible device to allow control from the terminal.
From the Applications menu, [DiXiM Player]
1
→
Select the server name of the terminal in
the server list.
[設定 (Settings)]→[
2
(Operation when tapping)]
で再生
(Play with remote device)]→[
ト機器を選択
Select the DLNA compatible device for
playback
タップ時の動作
→[リモート機器
(Select remote device)]
リモー
→
･
As device for playback, the DLNA compatible
devices that you performed playback previous time
are memorized.
Select playback type→Select a folder
3
Select a content
Play back the content on the player screen
4
◆
Playing back the DLNA compatible
→
device's contents on the terminal
･
Disclose contents on the DLNA compatible device to
allow access from the terminal in advance.
From the Applications menu, [DiXiM Player]
1
→
Select the server name of the DLNA
compatible device in the server list.
[設定 (Settings)]→[
2
(Operation when tapping)]
生
(Play with this device)]
･
Alternatively, you can play in another DLNA
compatible device by selecting [
(Play with remote device)] in [
(Operation when tapping)] and then selecting the
playback device in [
remote device)].
Select playback type→Select a folder
3
Select a content
Play back the content on the player screen
4
✔
INFORMATION
･
The terminal supports DTCP-IP. Link is not guaranteed for
all DTCP-IP compatible devices.
･
In the content selection screen, touch and hold a content
for 1 second or more, and slide it downward to download
the content. However, contents protected by copyright
cannot be downloaded.
タップ時の動作
→[この端末で再
リモート機器で再生
タップ時の動作
リモート機器を選択
(Select
→
94
Applications
◆
Setting DLNA server function
From the Applications menu, [DiXiM
1
Server]
Set each item
2
DiXiM Server :
サーバー名
displayed on the DLNA compatible device.
アクセス制御
期設定
access will be allowed from the DLNA compatible
device to the terminal. If unmarked, access will be
allowed only from the DLNA compatible device
marked in the [
devices)].
画面ロック中の動作
Set whether to continue server operation even
when screen unlock authentication is needed.
Mark to turn the DLNA function on.
(Server name) :
(Access control) :
(Initial settings of access right)] is marked,
Change the name
If the [
アクセス権の初
クライアント機器の一覧
(Operation during screen lock) :
(List of client
Clock
You can display a clock on the screen or set alarms.
From the Applications menu, [Clock]
1
The clock is displayed.
◆
Setting alarm
From the Applications menu, [Clock]
1
Perform target operations
2
Turning alarm on/off : Mark/Unmark alarm
Adding new alarm : [Add alarm]→Set time→Set
[Repeat]/[Alarm Sound]/[Vibrate]/[Label]→[Done]
Deleting alarm : Tap the time field (1 sec. or more)
[Delete alarm]→[OK]
[Done]
3
→
❖
When the preset alarm time is reached
The alarm operates according to the setting.
Stopping the alarm : [Dismiss] on the notification screen
Setting snooze : [Snooze] on the notification screen
･
The alarm activates after a specified time elapses.
Canceling snooze : Open the Notification panel→Tap a
snooze notification
Calendar
You can synchronize Calendar on the terminal with online
Google Calendar to manage schedules.
･
To use Calendar, you need to set up a Google account on
the terminal.
◆
Displaying the calendar
From the Applications menu, [Calendar]
1
■
Main operations in the Calendar screen
Switching display unit : [Day]/[Week]/[Month]
Switching to the display including today : [Today]
Selecting a calendar to synchronize/display :
[Settings]→Tap an account you want to synchronize/
display→Mark an account in the right list field
･
This item can be selected when you use two or more
calendars in online Google Calendar.
Setting a calendar : →[Settings]→[General
Preferences]→Set required items
→
→
95
Applications
◆
Registering a schedule
In the calendar screen,
1
･
When the calendar is activated for the first time or
not synchronized yet, a screen to add an account
appears. Add an account if required.
･
Alternatively, touch a time field for 1 second or
more to register.
Set required items→[Done]
2
❖
When the notification time is reached
Notification is made according to the setting. You can
cancel notification or set snooze in the following
procedure.
Open the Notification panel to tap
1
notification
Perform required operations
2
Canceling notification : Tap a notification
A detailed information screen appears and the
notification is canceled.
Deleting all notification : [Dismiss all]
Snoozing all notifications : [Snooze all]
Schedule is notified again in 5 minutes.
◆
Checking a schedule
You can view the details of events registered in Calendar.
Tap an event in the calendar screen
1
･
In the month display screen, tap the day then tap the
target event.
■
Operations on the event screen
Editing event : [Details]→[Edit]→Edit the event→[Done]
Deleting event : [Delete]→[OK]
Calculator
From the Applications menu, [Calculator]
1
Calculate
2
Deleting an entered character :
Deleting all mathematical expression : (1 sec. or
more)
Copying : Touch and hold mathematical expression
display field (1 sec. or more)
Electronic dictionary
You can use the electronic dictionary. You can also save
electronic dictionary recorded on the included Electronic
dictionary data DVD (sample) into a microSD card or the
internal memory to use.
From the Applications menu, [e-
1
Dictionaries+]
Enter a keyword→[Search]
2
Search result (list of results) appears.
Voice search : →Speak a keyword
Displaying Help :
You can check how to operate the electronic
dictionary.
Displaying version information :
Setting electronic dictionary : →[Misc Settings]
Set required items
Set font size, number of search results, operations for
playing movies or sound.
Managing dictionaries : →[Dictionary Manager]
Perform required operations
Move the dictionary saved in the internal/external
memory or delete it.
Tap a keyword you want to check
3
Descriptions appear on the right of the search results.
96
Applications
→
→
✔
INFORMATION
･
You can also use search by dictionary with which you can
specify a dictionary, complex search with which you can
specify several conditions or keywords, and batch search
with which you can search a word by several dictionaries.
･
Searched keywords can be saved in a vocabulary list or
use from the search history.
･
From the link for description, you can refer meaning of a
word, display an image, play a movie or sound.
･
When voice search is used or Wikipedia is used for search by
dictionary, a packet communication charge may be applied.
◆
Saving the electronic dictionary on
DVD to microSD card/internal
memory
You can save electronic dictionary recorded on the
included Electronic dictionary data DVD (sample) into a
microSD card/internal memory. Deleting electronic
dictionary saved in a microSD card/internal memory is
also available.
･
Windows XP (128 Mbyte or more of memory is
required.), Windows Vista (512 Mbyte or more of
memory is required.), Windows 7 (1 Gbyte or more of
memory for 32 bit, 2 Gbyte or more of memory for 64 bit
is required.) are supported.
･
To save all electronic dictionary recorded in the included
DVD, using a microSD/microSDHC card with 2 Gbyte or
more of remaining memory is recommended.
･
You can use only dictionary recorded on the included
Electronic dictionary data DVD (sample).
･
To connect the terminal and a PC with USB cable→P78
Set the DVD on a PC.
1
Following the onscreen instructions on the
2
"
辞書の追加・削除
dictionary)" screen, add or delete the
electronic dictionary on the DVD to or from
microSD card/internal memory.
(Adding/Deleting
Document Viewer
You can view Office documents (Word, Excel and
PowerPoint) etc.
From the Applications menu, [Document
1
Viewer]
Select a folder/file
2
･
Tap the screen to display icons. Perform the
following operations.
/ : Display the previous and next page
(sheet)
: Display the zoom control
: Specify a display range
: Return to the file list
･
Press in the viewer screen of each file to move,
search, show page, copy, set, share, set encoding,
show its version, etc. Available operations vary
depending on the file type.
✔
INFORMATION
･
The displayed content of Office documents may be
different from when they are displayed on a PC, or some
parts of the document may not be displayed.
97
Applications
International roaming
Available service overseas
Outline of international roaming (WORLD WING)
With the international roaming (WORLD WING), you can
use the terminal without changing phone number or mail
address in the service area of the overseas network
operator affiliated with DOCOMO. You can use SMS
without changing settings.
･
The terminal works in a 3G network and GSM/GPRS
network service area. Also, it works in countries or
districts where 3G 850 MHz is applied. Check the service
area. Since Xi area does not cover overseas, use 3G or
GPRS networks.
･
Refer to the following documents before using the
terminal overseas.
- "Mobile Phone User's Guide [International Services]"
- DOCOMO International Services website
-"
ドコモ海外利用
help
✔
INFORMATION
･
For Country codes, International call access codes,
Universal number international prefix, available
countries/regions, and network operators, refer to
"Mobile Phone User's Guide [International Services]" or
DOCOMO International Services Website.
(International roaming)" application
Main communication
services
SMS
*1
Mail
*1
Browser
Position location of GPS
*1
To use data communication during roaming, set Data roaming
setting to on.→P100
*2
For GPS positioning (Positioning location), a packet
communication charge is applied.
✔
INFORMATION
･
Some services are not available depending on the
overseas network operator or network.
98
3G
○○○
○○
○○
*2
○○
International roaming
GSM/
GPRS
GSM
×
×
×
Loading...