DNS WX56001 User Manual

说明书
成品80*45mm
120g道林纸单色
折页

封底

封面

Step 5:

Enter your Wi-Fi password to “CONTINUE”.

Tips: Wait until your speaker has been

powered-on for 30 seconds before continuing
to the next step.

Step 6:

Press and hold the Wi-Fi button to connect the
speaker to the Wi-Fi network, click on the
“CONTINUE” button when you hear the Prompt
Tone.
Tips: Prompt Tone goes like – Connecting to
your network, this may take 1~3 minutes.

Step 7:

Be patience, we are on the way…

Tips: Make sure your Wi-Fi network in normal

operation.

CONNECTED!

Great, now you could name for your speaker or
choose one from the list.
Finish Setup by clicking on the “CONTINUE”’
button.

Tips: Feel free to personalize your speaker at
your convenience.
Watch four pictures of speaker

5 6

⑦

①

④ ⑤

②

①

Microphone button: Short press the
microphone button to switch languages,
currently support language is English and
German.

②

Status indicator

③

AUX

④

Micro-USB

⑤

Power button: Long press the Power button
to turn it on/off

⑥

Wi-Fi button: Short press the Wi-Fi button to
switch between Wi-Fi Mode and Bluetooth
Mode. Blue Signal indicates for Bluetooth
Mode, while Green Signal for Wi-Fi Mode.
Long press the Wi-Fi button under Wi-Fi
Mode to connect the network.
Round Button: Adjust the volume by rotating

⑦

the round button, clockwise rotating for
volume up, the opposite site for volume
down.

③

⑥

introduction, then sign in your Amazon
account, you could ask for more from Alexa
with Omars dogo.

Important:

To commute between the WiFi and Bluetooth
connection, simply click the WiFi button (the
5th button on the scheme from page 2);If you
wish to connect via Bluetooth, long press the
WiFi button located at the bottom of the
speaker. The LED will flash blue while
establishing the connection, and when it’s
successful, it will constant light blue.

Warning: Changes or modifications to this

unit not expressly approved by the party
responsible for compliance could void the
user’s authority to operate the equipment.

NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio
communications.

OVERVIEW:

Thank you for purchasing this product!
Omars dogo is a smart speaker. Through the
application of up-to-date technologies, it
creates an experience of brand new music
listening and more.

IMPORTANT:
Before using this product, please carefully read

this manual:

Check the speaker’s power. A full charging is
recommended before use (Until the charging
indicator goes green).

Search for “Omars dogo” on App Store or
Google Play from your smartphone, download
and install it.
The product is equipped with a built-in battery.
Do not put it directly into fire, or it may cause
explosion or other dangers.

The product may radiate heat due to long-time
use or exposure to direct sunlight. This is
normal.

Do not use the device under any environment
with temperature lower than 0℃ (32℉) or
higher than 40℃ (104℉).

However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the follow ing
two conditions:
(1) this device may not cause harmful
interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
FCC RF Radiation Exposure Statement
Caution: To maintain compliance with the
FCC’s RF exposure guidelines, place the
product at least 20cm from nearby persons.

Do not use the speaker in humid place, for the
humidity may damage important parts of the
device.
Do not put the speaker directly into water.

QUICK START GUIDE:
(1). Power-on/off

Press and hold the Power button for about 3
seconds and release. The speaker will notify you
with a sound when it’s ready.

Important:

If power-on fails, charge the device first and
then try again.

(2). Charging

Use data cable included in the product pack for
charging the device. During charging, the
indicator displays in constant red light; when it
is fully charged, the indicator will turn green.

Important:

During the usage, if the level of the battery
drops and needs to be connected to a charger,
the red light above the micro-USB plug will
start flashing to notify you.

(3). Connecting to the app

DOGO ALEXA SPEAKER

USER MANNUAL

Step 1:

Get ready with Omars dogo and your Smart
Devices (phone/tablet) in hand.
Download app: Search for “Omars dogo” on
App Store or Google Play to download and
install.

Step 2:

Click on the “GET STARTED” button to move on.
Tips: Make sure your smart device
(phone/tablet) has been connected to a Wi-Fi
network before using our app “Omars dogo”.

Step 3:

Press and hold the power button for 3 seconds
until you see the green light begins to flash.
Click on the “CONTINUE” button to next step.
Tips: Upside down Omars dogo and you’ll find
the Power button on the bottom.

Step 4:

Connect your smart device to 2.4GHz Wi-Fi.
Click on the “CONTINUE” button to go to next
step.

Tips: Only applicable with 2.4GHz Wi-Fi network.

1 2 3

4