DNF Controls 4040CL-EVS-PBIO User Manual

12843 Foothill Blvd. Suite C
Sylmar, California 91342
V: 818.898.3380
F: 818.898.3360
[e-mail]

Model No. 4040CL-EVS-

PBIO

(& 4040CL-EVS-T-PBIO)

300 CLIP FAST ACCESS SYSTEM

FOR EVS DDRs

U

SER MANUAL

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 1 of 26

TABLE OF CONTENTS

1. REVISION HISTORY 4

GETTING STARTED . . . 5

2. SYSTEM

DESCRIPTION 5

DEFINITIONS 5

3. SYSTEM INSTALLATION 6

A. ST400-S/SM, VTR/DDR CONTROLLER 6
B. PRODUCTION SWITCHER 7

4. VIDEO SERVER SETUP 7

4. VIDEO SERVER SETUP 8

5. LOAD A CLIP 8

6. LEARN A CLIP OR CLIP COMBINATION 9

A. LEARN ON THE PRODUCTION SWITCHER 9
B. LEARN ON THE ST400 9

7. RECALL A CLIP OR CLIP COMBINATION 10

A. RECALL A CLIP FROM THE PRODUCTION SWITCHER 10
B. RECALL A CLIP FROM THE ST400 10

8. RECUE CLIP 10

9. CLEAR CUE POINTS 11

10. PLAY CLIP SEGMENT 11

11. PBIO ENABLE/DISABLE 11

12. PRODUCTION SWITCHER PBIO TRIGGER VALUES 12

ADVANCED FEATURES . . . 13

13. CREATE

ON

THE ST400 13

14. RETURN

CUE POINT LABELS 13

TO LIVE VIDEO 13

REFERENCE . . . 14

REFERENCE . . . 14

15. SETUP

MENU 14

16. FUNCTION TABLE 17

17. SPECIFICATIONS 19

RS422
POWER

SERIAL CONNECTOR 19

CONNECTOR 19

18. TROUBLESHOOTING 20
PBIO

TROUBLESHOOTING 20

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 2 of 26

19. SCREEN SHOTS 21

20. KEY LAYOUT 24

21. DNF CONTROLS LIMITED WARRANTY 25

Manual Version.........……............................................. 1.32 110606

Document ID......…............ 4040CL-EVS-PBIO_User_Manual.doc

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 3 of 26

1. REVISION HISTORY

100903 Rev. 1.1 Company header information revised.

112503 Rev. 1.2 Added DNF Controls Limited Warranty.

073004 Rev. 1.3 Revised GPI IN/OUT CONNECTOR.

052606 Rev. 1.31 Updated dimensions for T-bar and Non T-bar housings.
Added screen shots.

110606 Rev. 1.32 Corrected clip capacity.

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 4 of 26

Getting Started . . .

2. SYSTEM DESCRIPTION

The 4040CL system includes DNF’s most robust controller, the ST400, with the Cliplist software.
The ST400 controls up to 6 video channels individually or ganged. It features full transport
functionality.

The 4040CL provides fast access to fill clip and key clip combinations with the press of one key.

The 4040CL provides fast access to existing video clips stored in the EVS DDRS.

DEFINITIONS

 Throughout this document, DDR, VDR & Video Server will be referred to collectively as

“Video Server.”

 Words surrounded by brackets, for example, [ENTER], are keys on the ST400. [XXX] +

[XXX] means hold the two keys down simultaneously.

 The 6 keys directly below the display are referred to as “Softkey.” Their function changes as

indicated on the last line of the display.

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 5 of 26

3. SYSTEM INSTALLATION

a. ST400-S/SM, VTR/DDR CONTROLLER

1) Plug one end of a 9-conductor, RS422 serial cable into the VTR1 (2, 3, 4, 5 or 6)
connector on the rear of the ST400. Plug the other end of the cable into the 9-pin
REMOTE connector on the Video Server.

2) Connect the supplied POWER SUPPLY, APX#4108, into the POWER connector
on the rear of the ST400. Plug the Power Supply into an outlet, 90 VAC - 240
VAC.

3) Check SETUP MENU prior to using the ST400 to confirm proper Record mode
and other User settable modes.

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 6 of 26

b. PRODUCTION SWITCHER

1) Plug one end of a 9-conductor, RS422 serial cable into the “PBIO” connector on
the rear of the ST400. Connect the other end of the cable to the Peripheral Bus
Connector on the production switcher.

2) Refer to “SETUP MENU,” Section 15 to set VTR1, VTR2, VTR3, VTR4,
VTR5, & VTR6 Pbus Device Addresses, PBIO parity to match the Production
Switcher, and Production Switcher type.

The Pbus baud rate must be set to “38400” on the Production Switcher.

3) Configure the production switcher:

On the production switcher -

Enable the Peripheral Bus.
Enable the Peripheral Device Addresses assigned to the ST400.
Enable the appropriate Learn/Recall levels.
Enable the Timeline or Recall Trigger function.

Installation is complete.

CONNECTION DIAGRAM

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 7 of 26

4. VIDEO SERVER SETUP

a. Select SONY DD35 communications protocol on the EVS Remote.

b. Select “2 Remote” or “3 Remote” option on the EVS Remote.

5. LOAD A CLIP

a. Select a VTR by pressing VTR [1], [2], [3], [4], [5] o r [6].

b. Press [CLIP LIST] to view the list of CLIP IDs that are resident on the Video Server.

The CLIP LIST indicator will turn on.

c. Turn the Wheel to view the existing CLIP IDs on the video server.

Turn the Wheel clockwise to scroll forward, or counter-clockwise to scroll backward,
through the list of available CLIPs. Backward scrolling is limited to the last 10 screens of
CLIP IDs viewed.

Press [LOAD] to load the highlighted CLIP ID. After loading the selected clip, the CLIP
LIST function will terminate. The CLIP LIST indicator will turn off.

OR

Manually enter a Clip ID using the ST400 numeric keypad, or PC keyboard.

d. Press [LOAD] to load the entered CLIP ID for playout.

e. Repeat steps a. and b. to load clips on desired VTRs.

f. Set the Gang Mode, if required. See ‘GANG SETUP” in “FUNCTION TABLE,”

Section 15.

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 8 of 26

6. LEARN A CLIP OR CLIP COMBINATION

a. LEARN ON THE PRODUCTION SWITCHER

1) On ST400, Load a clip(s) on the desired VTR(s). (See “LOAD A CLIP,”
Section 4.

2) Select and enable the Peripheral Device Addresses for the ST400.

3) Do a LEARN to the desired REGISTER.

The ST400 will: LEARN (save) the VTR number, loaded CLIP ID and current
IN & OUT time into the REGISTER number in the ST400.

b. LEARN ON THE ST400

1) Press VTR [1], [2], [3], [4], [5] or [6] to select the channel to learn.

2) Load a clip on the selected channel. See section LOAD A CLIP.

3) Use the transport functions to view the clip.

Press [IN] to mark an IN point. The IN LED will turn on.
On recall, the clip will cue to the IN time, not the beginning of the clip.

Optional- Press [OUT] to mark an OUT point. The OUT LED will turn on.
On recall, the clip will play to the OUT point then stop.

To delete an IN or OUT point, press and hold [DEL], then press [IN] or [OUT].

The IN/OUT LED will turn off.

If no IN point is marked, the current location of the clip will be learned as the IN
point.

4) For GANGs, repeat steps a. and b. for each channel.

Then, press the [GANG] softkey.

Press VTR [1], [2], [3], [4], [5] or [6] to add it to the GANG. The VTR led will
turn on.

Press the VTR key again to remove it from the gang. The VTR led will turn off.

Press [ESC] to exit GANG mode. The LEDs of all GANGed VTRs will turn on.

5) Select the desired Cue Point by pressing [NEXT CUE], [LAST CUE] or by
manually entering the Cue Point using the numeric keypad, followed by
[ENTER].

The selected Cue Point number is shown on the bottom part of the display.

6) Press [SHIFT] + [LEARN] to in itiate the LEARN.

The display will show: “Select VTRs to learn:--------”

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 9 of 26

7) Select the VTRs to learn by pressing VTR keys [1], [2], [3], [4], [5], and or [6].

8) Press [LEARN] to complete the learn process.

NOTE: LEARN will overwrite the previous contents o f the Shotkey.

Press [ESC] at anytime to escape without LEARNing.

7. RECALL A CLIP OR CLIP COMBINATION

a. RECALL A CLIP FROM THE PRODUCTION

SWITCHER

1) On the ST400 in the SETUP MENU, set the desired PB addresses for the
selected ST400 VTR channels that will be controlled by the Production Switcher.

2) On the Production Switcher, select and enable the PB addresses for the ST400
VTR channels that will be controlled.

3) On the Production Switcher, recall the desired REGISTER.

The ST400 will automatically load the Learned clips on the Learned VTRs, set the
Learned IN and OUT points, cue the clips to the Learned IN point, set the Learned GANG
mode.

b. RECALL A CLIP FROM THE ST400

1) Select the desired Cue Point by pressing [NEXT CUE], [LAST CUE] or by
manually entering the Cue Point using the numeric keypad.

The selected Cue Point number is shown on the bottom of the display.

2) Press [LOAD] on the ST400.

The ST400 will automatically load the Learned clips on the Learned VTRs, cue
the clips to the Learned IN time, then set the Learned GANG mode.

8. RECUE CLIP

a. Press [RECUE]. If an IN Point is marked (the IN indicator is on), the clip will RECUE to

the IN Point.

b. Press [CUE OUT] to cue to the marked OUT point.

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 10 of 26

9. CLEAR CUE POINTS

a. Select the cue point to be cleared using [NEXT CUE], [LAST CUE], or manually

entering the cue point number.

b. Press [SHIFT] + [LEARN].
The CLEAR softkey will be displayed on the bottom of the display.

c. Press the [CLEAR] softkey to clear the cue point.
The cue point will be cleared and the d isp lay will return to the normal screen.
OR

Press [ESC] to escape without clearing.

10. PLAY CLIP SEGMENT

a. Set an IN Point and

Jog/Shuttle to the desired IN point. Press [IN].
Jog/Shuttle to the desired OUT point. Press [OUT].

OR

Press [SHIFT] + [IN]. Manually enter the IN time on the numeric keypad. Press
[ENTER].

Press [SHIFT] +[OUT]. Manually enter the OUT time on the numeric keypad. Press
[ENTER].

b. Press [RECUE]. The clip will cue to the IN point.

c. Press [PLAY].
The clip will play from its current time to the OUT point, then stop.

OUT Point.

11. PBIO ENABLE/DISABLE

On the ST400 press the [PBIO] softkey to enable or disable PBIO. When disabled, the ST400 will
ignore all Pbus commands. When enabled, the ST400 will respond to all Pbus commands.

When enabled and Pbus commands are received, the softkey’s LED will flash.

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 11 of 26

12. PRODUCTION SWITCHER PBIO TRIGGER VALUES

The Production Switcher outputs a Peripheral Bus trigger at specific Timeline key frames, as
programmed by the operator. The 2044CL performs a specific function for each trigger value:

GRASS VALLEY GROUP Production Switcher

Trigger Value Mode

0 Play (If OUT point is specified, stop at OUT.)
1 Recue to beginning of clip
2 Slo-mo using ST400 Preset Speed
3 Reverse Play
4 Still Frame
5
6 Record
7 or greater Play

SONY Production Switcher

Trigger Value Mode

0 Recue to beginning of clip Play
1 Play (If OUT point is specified, stop at OUT.)
2 Slo-mo using ST400 Preset Speed
3 Reverse Play
4 Still Frame
5
6 Record
7 or greater Play

To control more than one VTR, enable the Peripheral Device Address for each VTR. The Trigger
value will be sent to the enabled devices.

OR

GANG the required VTRs on the ST400. See “FUNCTION TABLE,” Section 16, for GANG
instructions. Enable the Peripheral Device Address for one of the GANGed VTRs. The Trigger
will be sent to the enabled VTR. The other VTRs in the GANG will perform the same action.

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 12 of 26

Advanced Features . . .

13. CREATE CUE POINT LABELS

Use LABELS mode to assign meaningful names to cue points. LABELS provides a faster and
easier method to select cue points.

ON THE ST400

a. In Setup Menu, turn LABEL MODE on.

b. Select cue point to label.

c. Press the [LABEL] key.

d. Manually enter a label, up to 8 characters in length, using the numeric keypad, or PC

keyboard.

e. Press the [ENTER] to assign the entered label to the selected cue point.

OR

[ENTER] on the PC keyboard.

OR

[NEXT CUE] or [LAST CUE].

NOTE - Labels are saved in non-volatile memory in the ST400. They are not saved in the video
server.

14. RETURN TO LIVE VIDEO

a. Make sure Record set to “Crash” in the menu.

b. Press [REC] key. The corresponding CAM clip will be loaded, the video returns to live.

OR

Press [SHIFT] + [REC] to switch to live video.
Press [SHIFT] + [REC] repeatedly to toggle between camera angles.

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 13 of 26

Reference . . .

15. SETUP MENU

Press [MENU]. The MENU indicator will turn on.
The display will show the following parameters with their current settings.

Turn the wheel to select a menu option.
Press the [CHANGE] softkey to modify the current setting.

Press the [EXIT] softkey to exit the Setup Menu.

PARAMETER DESCRIPTION

WIND MODE

RECORD MODE Press [MENU] to select the desired record mode:

SLOMO Press the [TBAR] (or [WHEEL]) softkey to select the T-bar or wheel for slomo.

SYNC Select the appropriate softkey to enable or disable the Reference Video input. [ON] [OFF]

Press Softkey to select:
HOLD (Fast wind is maintained only while key is depressed.)
OR
LATCH (Fast wind is maintained after key is released.)

Set the fast wind speed (3.9 to 23.7) by pressing the [SPD] softkey.

Lockout, Assemble, Crash (Full) or Insert.

in INSERT mode: Press the associated Softkey, located below the display, to toggle

Only
Video(V), Audio1(A1), Audio2(A2), Audio3(A3) on/off, Audio4 (A4) on/off.

For T-bar:

The T-BAR has a speed range of 0Î2x with a detent at 1x play speed
OR a range of 0Î1x (detent at 1x Play speed).

Press [SPD-RNG] softkey to toggle between SLOMO speed ranges:
0 Æ 1x OR 0 Æ 2x.

Press [BACK] softkey to return to SLOMO MENU.

Press [ESC] to exit OR turn the Wheel to select another item.

For Wheel:

Press the [PRSET] sofkey to toggle between UPDATE and STATIC modes.

UPDATE- When exiting SLOMO mode, the last used speed is saved in the Preset

Speed register.

STATIC- The Preset Speed register is NOT updated when exiting SLOMO mode.

It is only changed by [SHIFT] + [SLOMO] (PRESET SLOMO).

Press [SPD-RNG] softkey to toggle between SLOMO speed ranges:
0 Æ 1x OR 0 Æ 2x.

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 14 of 26

PARAMETER DESCRIPTION

RECORD KEY

RECALL
MODE

PREROLL

RECORD
DELAY

GANG
MODE

STANDARD Press [NTSC] or [PAL] to select the video standard for time calculations.

LABEL
MODE

CLEAR
MEM

Select single button or 2-button record:

RECORD = [REC] Only

OR RECORD = [REC] + [PLAY]

Press [NORMAL] or [REDIR] (redirect).

REDIR­When one and only one clip is learned into a Cue Point, the Clip will be REDIRECTED to load
on the currently selected VTR

NORMAL­The cue point will load on the learned VTR.

Enter Preroll value.

Enter delay value. (Used by CAPTURE function.)

[PERM] Permanent Gang-
The GANG can be created and undone only with the [GANG] softkey.

[TEMP] Temporary Gang­Quickly create a GANG by pressing and holding a VTR key, then pressing other VTR keys.
Quickly undo the GANG by pressing any VTR key.

Press [ON] or [OFF]. (See LABEL section for description.)

ON­Display a user-entered LABEL instead of the actual CLIP ID.

OFF­Display actual CLIP ID.

[DEFAULTS] [CLR – CUES] [CLR – BANK] [BACK]

DEFAULTS
Set ST400 to factory defaults. Follow the prompts on the display.
Press [YES] to continue or press [NO] to exit without changing ST400.

CLR – BANK
Clears all cue points in the selected bank. Follow the prompts on the display.

CLR – CUES
Clears all cue points in all banks. Follow the prompts on the display.

BACK
Return to prior menu item.

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 15 of 26

PROTOCOL Select [DD35] or [SONY].

[DD35]
Select DD35 to allow clip functionality: Load, Recue, View available Clips.

[SONY]
Select SONY to control video server like a VTR. In this mode, the clip must have already been
loaded.

PB ADDRESS Select [VTR1], [VTR2], [VTR3], [VTR4], [VTR5], or [VTR6].

Assign Pbus Device Address to selected VTR by entering an address between 0 and 23 using
numeric keypad.

OR

Press DEL to turn off Pbus control for the VTR.

PB SWITCHER Select [GRASS VALLEY] or [SONY] Production Switcher. For Philips, use Grass Valley.

PBIO PARITY Press [NONE], [ODD] or [EVEN] parity to match the Pbus setting on your Production

Switcher.

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 16 of 26

16. FUNCTION TABLE

Function Key Press Description

CUE TO OUT
POINT

FFWD

GOTO
ENTERED TIME

GANG SETUP

JOG
LAST CUE

NEXT CUE

[CUE OUT]

[FFWD]

[SHIFT] + [RECUE]

[GANG]

[JOG]
[LAST]

[NEXT]

If OUT point is marked, cue to the OUT point.

Press and HOLD to shuttle. Release key to stop. Set WIND
Speed in MENU.

Search the VTR to the manually entered time.

Use the ST400 numeric keypad. Press [ENTER] or [RECUE].

Individually press the VTR keys to be included in the gang. The
LED above the key will turn on. Press the VTR key again to
remove from gang, the LED above the key will turn off.
Press [ESC] to exit.

Upon exiting, all members of the gang will have their VTR LEDs
turn on. The flashing LED shows which VTR is currently
selected.

Select JOG mode and enable Wheel.
Step to the previous Cue Point Location.

Step to the next Cue Point Location.

PREROLL

LIVE ON
CURRENT
CHANNEL

REWIND

SHUTTLE
SLOMO

SLO-MO SPEED
PRESET

[PREROLL]

[REC]

[RWD]

[SHUTTLE]
[SLOMO] Press [SLOMO] to slo-mo the VTR. Turn the Wheel

[SHIFT] + [SLOMO] For WHEEL ONLY: Press [SHIFT] + [SLOMO] to preset the

If an IN point is marked, preroll to the IN point using the
PREROLL VALUE in the Setup Menu.

Places VTR into the Live mode.
Press [RECORD] OR [RECORD] + [PLAY].

Press and HOLD to shuttle. Release key to stop. Set WIND
Speed in MENU.

Select SHUTTLE mode and enable Wheel.

(or move the T-Bar, if available) to change the play speed.
Press [SLOMO] to STILL frame
OR press any transport key to exit SLOMO.

slo-mo speed. Turn the Wheel to select desired speed.
Press [ESC] or any transport key to exit.

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 17 of 26

Function Key Press Description

STOP

PLAY

PLAY- SIMPLE

RECUE

PBIO ENABLE/
DISABLE

LIVE ON
DIFFERENT
CAMERA
ANGLES

[STOP]

[PLAY]

[SHIFT] + [PLAY]

[RECUE]

[PBIO]

[SHIFT] + [REC]

Press once to STILL frame VTR.
Press again to put VTR into STOP mode.

If an OUT point is marked, play to the OUT point and stop. If no
OUT point is marked, play normally.

Play normal.

If the IN point is marked, cue to the IN point.

PBIO LED is ON if PBIO is enabled. Toggle the key to
temporarily disable all PBIO signals. The key blinks when a
valid PBIO command is received from the Production Switcher.

Returns to Live Video on a current channel. Press the key
combination again to toggle between available camera angles.

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 18 of 26

17. SPECIFICATIONS

Power: 90 VAC to 265 VAC adapter supplied with IEC connector
APX Model #AP4108

+5v @ 4A, +12v @ 1.0A, -12V @ 0.6A

Size:

Non-Tbar (H x W x D) 1 3/4 (front) x 3 3/8 (rear) x 11 3/8 x 6 1/2

(8 5/8 high to top of display)

T-bar (H x W x D) 1 3/4 (front) x 3 3/8 (rear) x 13 3/4 x 6 1/2

(8 5/8” high to top of display)

Weight: 10 lbs.

Rear Panel Connectors: VTR1, 2, 3, 4, 5,6 (All DB9F)
GPI (DBF25F)
Power (DB9M)
SHOTBOX (DB9F)
PBIO (DB9F)
Keyboard (6-pin mini DIN)
Ref. Video In (BNC)
Ground Threaded stud.

Display: Easy to read, back-lit LCD display

Jog/Shuttle Wheel: With mechanical detents

RS422 SERIAL CONNECTOR

9-Pin D-Type, Female (DB9F)

Pin # 1 Frame Ground 6 Receive Common
2 Receive A Í 7 Receive B Í
3 Transmit B Î 8 Transmit A Î
4 Transmit Common 9 Frame Ground

5 Spare

POWER CONNECTOR

9-Pin D-Type, Female (DB9M)

Pin # 1 +5v DC 6 +5 VDC
2 +5v DC 7 Ground
3 Ground 8 Ground
4 +12 VDC 9 Ground

5 –12 VDC

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 19 of 26

GPI IN/OUT CONNECTOR
26-Pin D-Type, Female (DB26F)

Pin # Function Pin # Function

1 No Connection 14 GPI #5 Last Cue
2 No Connection 15 GPI #6 Recall
3 No Connection 16 No Connection
4 No Connection 17 No Connection
5 No Connection 18 Ground
6 No Connection 19 +5V
7 No Connection 20 +5V
8 No Connection 21 No Connection
9 Ground 22 No Connection
10 GPI #1 Play 23 No Connection
11 GPI #2 Stop 24 No Connection
12 GPI #3 Recue 25 No Connection
13 GPI #4 Next Cue 26 Ground

18. TROUBLESHOOTING

PBIO TROUBLESHOOTING

Press [SHIFT] + [PBIO]. The display will show PBIO DATA.

All Pbus commands received from the production switcher will be shown on the display.
Communication errors due to parity mismatch or baud rate mismatch will be shown as ‘-‘. If no
command data is shown, then no commands are being received from the production switcher.
Check the Production Switcher’s Pbus set. Also check the cabling between the Production
Switcher and ST400.

Press [SHIFT] + [PBIO] to exit this test mode.

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 20 of 26

19. SCREEN SHOTS

4040CL & 2044CL Main Screen

(Not to scale)

TM 00:00:00:00

PLAY MODE: NORMAL (REC MODE: LOCKOUT)
LOADED:

CLIP:
IN: --:--:--:-- DUR:--:--:--:-­ OUT: --:--:--:-- SPEED: +0.00

Q000
Clip: CLIPNAME

IN: 00:00:00:00 DUR: 00:00:00:00
OUT: 00:00:00:00
VTRS: 1 3 5

VTR1

CUE-OUT GANG

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 21 of 26

4040CL & 2044CL GANG Screen

(Not to scale)

TM 00:00:00:00

PLAY MODE: NORMAL (REC MODE: LOCKOUT)
LOADED:

CLIP:
IN: --:--:--:-- DUR:--:--:--:-­ OUT: --:--:--:-- SPEED: +0.00

Select VTRs to gang: 1 - 3 - 5 -

Q000
Clip: CLIPNAME

IN: 00:00:00:00 DUR: 00:00:00:00
OUT: 00:00:00:00
VTRS: 1 3 5

VTR1

CUE-OUT GANG

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 22 of 26

4040CL & 2044CL Clip List Screen

(Not to scale)

TM 00:00:00:00

PLAY MODE: NORMAL (REC MODE: LOCKOUT)
LOADED:

CLIP:
IN: --:--:--:-- DUR:--:--:--:-­ OUT: --:--:--:-- SPEED: +0.00

►►►CLIP0001
CLIP0002
CLIP0003
CLIP0004
CLIP0005
CLIP0006
CLIP0007
CLIP0008
CLIP0009
CLIP0010

Turn Wheel to view clips, LOAD to Load.
Press [CREATE] to Create a new clip.
Press ENTER to manually enter clip ID.

VTR1

CREATE ESC

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 23 of 26

20. KEY LAYOUT

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 24 of 26

21. DNF CONTROLS LIMITED WARRANTY

DNF Controls warrants its product to be free from defects in material and workmanship for a period of one
(1) year from the date of sale to the original purchaser from DNF Controls.

In order to enforce the rights under this warranty, the customer must first contact DNF’s Customer Support
Department to afford the opportunity of identifying and fixing the problem without sending the unit in for
repair. If DNF’s Customer Support Department cannot fix the problem, the customer will be issued a
Returned Merchandise Authorization number (RMA). The customer will then ship the defective product
prepaid to DNF Controls with the RMA number clearly indicated on the customer’s shipping document.
The merchandise is to be shipped to:

DNF Controls
12843 Foothill Blvd., Suite C
Sylmar, CA 91342
USA

Failure to obtain a proper RMA number prior to returning the product may result in the return not being
accepted, or in a charge for the required repair.

DNF Controls, at its option, will repair or replace the defective unit. DNF Controls will return the unit
prepaid to the customer. The method of shipment is at the discretion of DNF Controls, principally UPS
Ground for shipments within the United States of America. Shipments to international customers will be
sent via air. Should a customer require the product to be returned in a more expeditious manner, the return
shipment will be billed to their freight account.

This warranty will be considered null and void if accident, misuse, abuse, improper line voltage, fire, water,
lightning or other acts of God damaged the product. All repair parts are to be supplied by DNF Controls,
either directly or through its authorized dealer network. Similarly, any repair work not performed by either
DNF Controls or its authorized dealer may void the warranty.

After the warranty period has expired, DNF Controls offers repair services at prices listed in the DNF
Controls Price List. DNF Controls reserves the right to refuse repair of any unit outside the warranty period
that is deemed non-repairable.

DNF Controls shall not be liable for direct, indirect, incidental, consequential or other types of damage
resulting from the use of the product.

# # #

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 25 of 26

4040CL-EVS-PBIO, 300 Clip Fast Access System, EVS DDRs Page 26 of 26