DMtex D9000 SR, D9000 T / A1R, D9000 T / A1S, D9000 MSR Installation And Operation Manual

ISO 9001:2008 Certified Company

№ 34, етаж 5,

Tel./Fax: [phone]
e-mail: [e-mail]
web: www.dm-teh.com
Address: Pleven, Bulgaria 5800

ул.”Ген.л-т Ат. Стефанов”

Installation and operation conventional fire detectors

D9000 series

Nom.№

Type

Characteristics

Sensitivity / Class

1001

D9000 SR

Optical smoke detector

EN 54-7

1002

D9000 T / A1R

Rate of rise heat detector

A1R, EN 54-5

1003

D9000 T / A1S

Fixed temerature heat detector

A1S, EN 54-5

1004

D9000 MSR

Combines optical smoke and heat detector

A1R, EN 54-5 / EN 54-7

Caution : Read this manual before attempting to install the detector.

1. Technical specifications

– Supply voltage 9-30 V DC
– Power consumption in Duty condition ≤ 130 µА
– Consumption in " Fire " condition 20 mА/ 24V DC
– limiting resistor output 2kΩ
– Degree of protection IP 40
– Cross section of the connecting wire 0,4÷2,0 mm2
– Operating temperature range 10ºС ÷ 50ºС
– Humidity (93 ± 3)% при 25ºС
– Dimensions with base f 100mm h ≤ 52mm
– Weight ≤ 100g

– Mounting the detector

– Choose the place (according to the plans of the project) for the installation of the detector ;
– Mount the base with appropriate fixings ;
– Connect the electrical cables according to the attached diagram ( Figure 1) ;);

Fig.1

– Place the detector base and rotate clockwise till matching markers;
– If you want to lock detector ::

 Pre remove the key from the base ( Figure 2).
 Break the plastic at the specified location on the bottom of the sensor ( Figure 3 ).

Instructions for installation and commissioning conventional of fire alarms D9000 series

Fig.2 Fig.3 Fig.4

 Place the detector base and rotate it .

– If the detector is locked to the base, to unlock it , insert first the key to the specified location

(Fig. 4) and rotate the detector counterclockwise;

– Test the detector to check the correct operation of the LED indication;
– During normal operation, the LEDs blink for 16 seconds.

2. Testing and Maintenance

 Testing

– Apply power;
– Wait about a minute or until the detector begins to blink;
– Activate the detector test spray and / or temperature sonda. The two red LEDs must illuminate

permanently.

 Service maintenance

– Visual inspection for mechanical damage and pollution - once a year;
– Verification of performance - once a year;
– Prophylactic cleaning - depending on the environment in which it is located.

Optical detectors D9000 SR/MSR are software tested and when the detector is contaminated, it is signaled
by flashing LEDs for 2 seconds to 2 seconds .

D9000 Series detectors are compatible with all conventional power plants, that have met the requirements
of a standards EN54.

The detectors are available with three types of bases:

– In 9000 - a standard basis;
– In 9000D - standard base with diode for recording damage detector down;
– In 9000R - standard base with relay output 12V for security panels.

3. Warranty obligations

The manufacturer guarantees the conformity of the device with standards EN 54-5 and EN54-7. The
warranty period is 24 months from the date of sale , provided that:

– the conditions of storage and transport have been followed;
– release is performed by authorized persons;
– the requirements for operation stated in this instruction have been abode.
– defects are not caused by natural phenomena and accidents of the plug socket.

When there is the need of warranty repair , please contact us by phone or email to give you guidelines for
the warranty obligations of the company. Repairs are carried out in the company's service company.

Tel./Fax: [phone]

e-mail: [e-mail]

DMTeh wishes you pleasant work!