DMP Electronics Vortex86MX PMX-089T-5A, Vortex86MX PMX-089T-8A, Vortex86MX PMX-089T-5A-512, Vortex86MX PMX-089T-8A-512 User Manual

Page 1
PMX-089T-5A / PMX-089T-8A
PMX-089T-5A-512 / PMX-089T-8A-512
with 8.9” TFT LCD
User’s Manual
Page 2
ii
Copyright
The information in this manual is subject to change without notice for continuous improvement in the product. All rights are reserved. The manufacturer assumes no responsibility for any inaccuracies that may be contained in this document. And makes no commitment to update or to keep current the information contained in this manual.
No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part, in any form or by any means without the prior written permission of the
DMP Electronics Inc.
Trademarks Ac knowledgment
Vortex86MX is the registered trademark of
DMP Electronics Inc. Other brand names or product names appearing in this document are the properties and registered trademarks of their respective owners. All names mentioned herewith are served for identification purpose only.
S afety Information
Read these Safety instructions carefully. Make sure the voltage of the power source is correct before connecting the equipment to
the power outlet.
Do not expose your Panel PC to rain or moisture, in order to prevent shock and fire
hazard.
Keep PMX-089T away from humidity. Do not open the cabinet to avoid electrical shock. Refer to your nearest dealer for
qualified personnel servicing.
Never touch un-insulated terminals or wire unless your power adaptor is disconnected. Locate your Panel PC as close as possible to the socket outline for easy access and to
avoid force caused by entangling of your arms with surrounding cables from the Panel PC.
USB connectors are not supplied with Limited Power Sources. If the equipment is not used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
DO NOT ATTEMPT TO OPEN OR TO DISASSEMBLE THE CHASSIS
(ENCASING) OF THIS PRODUCT. PLEASE CONTACT YOUR DEALER FOR
SERVICING FROM QUALIFIED TECHNICIAN.
Page 3
T a b l e o f C o n t e n t s
T a b l e o f C o n t e n t s ............................................................. iii
C h a p t e r 1 General Information..…………………………………1
1.1 Product Description ................................................ 1
1.2 Product Specifications ............................................ 2
1.3 Inspection standard for TFT-LCD Panel ................. 4
1.4 Product Dimension ................................................. 7
1.5 Ordering Information .............................................. 8
1.6 Packing List ............................................................ 8
C h a p t e r 2 System Installation ................................................. 9
2.1 CPU Board Outline ................................................. 9
2.2 Connector Summary ............................................ 10
2.3 Connector Pin Assignments ..................................11
2.4 External I/O Overview .......................................... 14
2.5 External I/O Pin Assignment ................................. 15
2.6 System Mapping ................................................... 17
2.7 Watchdog Timver ................................................. 20
C h a p t e r 3 Driver Installation…..………………………………..21
3.1 PMX-089T Development Note .............................. 22
3.2 BIOS Defaul Setting ............................................. 23
Warranty ............................................................................................ 24
Page 4
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
1
C h a p t e r 1
General Information
1.1 Product Description
PMX-089T is an ultra compact platform for the present demanding embedded and productive
applications. It has new Vortex86MX SoC CPU which consumes only minimum power
requirement when running at 1GHz, and DDR2 memory provides faster data transfer rate. By
using 8.9” TFT LCD, PMX-089T becomes the perfect choice for a limited budget. In additional,
the integrated 10/100M Ethernet port supplies the communication capability which makes
PDX-089T can be more widely used when running with Linux, Windows CE, and Windows XP
environment to become the perfect solution for system integration.
8.9” WSVGA TFT LCD 4-Wire Resistive Touch Panel DM&P Vortex86DX SoC 1GHz 512MB/1GB DDR2 system memory AMI BIOS 2 watchdog timer Compact Flash Type I/II / Micro SD 10/100Mbps Ethernet 2 USB 2.0 (host)
1 RS-232/485/422 ports Wi-Fi Optional Audio Out Single voltage +5V DC(5A Version) Multi voltage +8~+35V DC(8A Version) Fanless Design Operating temperature range of 0°C to
+50°
Page 5
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
2
1.2 Product Specification
CPU Board Specifications
CPU
DM&P Vortex86MX 1GHz
Cache
L1:16KB I-Cache, 16KB D-Cache
L2: 256KB Cache
BIOS
AMI BIOS
Memory
512MB/1GB DDR2 onboard
Watchdog Timer
Software programmable from 30.5u to 512 seconds x 2 sets
LAN
Integrated 10/100M Ethernet
Audio
HD Audio-Realtek ALC262 CODEC
Internal Drives
Compact Flash Type I/II slot
Micro SD slot
I/O
RS-232/422/485 x 1
USB ports (Ver2.0) x 2
RJ-45 Port x 1
Mechanical & Environment
Power Requirement
Single Voltage +5VDC ( 5A )
Multi Voltage +8~+35VDC ( 8A )
Power Consumption
1.5A@5VDC
Operating Temperature
0 ~ +50 ( 32 ~ +122 ℉)
Storage Temperature
-10 ~ +60 ( 14 ~ +140 ℉)
Operating Humidity
0% ~ 90% relative humidity, non-condensing
Dimensions
236.6 x 146 x 35mm (9.31 x 5.75 x 1.38 inches)
Weight
468g
Front Panel Protection
IP 65
Certification
CE, FCC, VCCI, Vibration
Page 6
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
3
LCD Specifications
Display Type
8.9” TFT LCD
Backlight Unit
LED
Display Resolution
1024(W) x 600(H)
Brightness (cd/m2)
220 nits
Contrast Ratio
500:1
Display Color
262,144
Pixel Pitch (mm)
190.5 (H) x 189 (V)
Viewing Angle
Vertical 110
o
,
Horizontal 140
o
Backlight Lifetime
25,000 hrs
Touchscreen
Type
Analog Resistive
Resolution
Continuous
Transmittance
80%
Controller
PS/2 interface
Software Driver
DOS/Linux/WinCE/WinXP
Durability
1 million
Page 7
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
4
1.3 Inspection standard for TFT-LCD Panel
DEFECT TYPE LIMIT Note
VISUAL
DEFECT
INTERNAL
SPOT
φ<0.15mm
Ignore
Note1
0.15mmφ0.5mm N4
0.5mmφ
N=0
FIBER
0.03mm<W
0.1mm, L5mm N3
Note1
1.0mmW, 1.5mmL
N=0
POLARIZER BUBBLE
φ<0.15mm
Ignore
Note1
0.15mmφ0.5mm N2
0.5mmφ
N=0
Mura It’ OK if mura is slight visible through 6%ND filter
ELECTRICAL
DEFECT
BRIGHT DOT
A Grade B Grade
C Area O Area Total C Area O Area Total
Note3
N0 N2 N2 N2 N3 N5
Note2
DARK DOT
N2
N3 N3 N3 N5 N8
TOTAL DOT
N4 N5 N6 N8
Note2
TWO ADJACENT DOT
N0
N1
pair
N1
pair
N1
pair
N1
pair
N1
pair
Note4
THREE OR MORE
ADJACENT DOT
NOT ALLOWED
LINE DEFECT NOT ALLOWED
(1) One pixel consists of 3 sub-pixels, including R,G, and B dot.(Sub-pixel = Dot)
(2) LITTLE BRIGHT DOT ACCEPTITABLE UNDER 6 % ND-Filter
(3) If require G0 grand (Total dot N
0), please contact region sales.
Page 8
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
5
[Note1] W : Width[mm], L : Length[mm], N : Number, φ: Average Diameter
[Note2] Bright dot is defined through 6% transmission ND Filter as following.
Page 9
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
6
[Note3]
C Area: Center of display area C Area: Outer of display area
[Note4]
Judge defect dot and adjacent dot as following. Allow below (as A, B, C and D status) adjacent
defect dots, including bright and dart adjacent dot. And they will be counted 2 defect dots in total
quantity.
(1) The defects that are not defined above and considered to be problem shall be reviewed and
discussed by both parties.
(2) Defects on the Black Matrix, out of Display area, are not considered as a defect or counted.
Page 10
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
7
1.3 Product Dimension
Page 11
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
8
1.4 Ordering Information
Part Number Description
PMX-089T-5A 8.9” Panel PC w/1GB
DDR2/2USB/Line-Out/LAN/COM/CF/MicroSD/Power Adapter
PMX-089T-8A 8.9” Panel PC w/1GB
DDR2/2USB/Line-Out/LAN/COM/CF/MicroSD/8-35 DC support
PMX-089T-5A-512 8.9” Panel PC w/512MB
DDR2/2USB/Line-Out/LAN/COM/CF/MicroSD/Power Adapter
PMX-089T-8A-512 8.9” Panel PC w/512MB
DDR2/2USB/Line-Out/LAN/COM/CF/MicroSD/8-35 DC support
1.5 Packing List
Part Number Package
PMX-089T-5A
PMX-089T-5A Power-20W-3PIN
PMX-089T-8A
PMX-089T-8A
PMX-089T-5A-512
PMX-089T-5A-512 Power-20W-3PIN
PMX-089T-8A-512
PMX-089T-8A-512
WLAN KIT (Optional)
USB-WLAN-IPEX-KIT WIRELESS-ANTENNA-157 WIRELESS-CABLE-150MM
Page 12
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
9
C h a p t e r 2
System Installation
2.1 CPU Board Outline
Page 13
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
10
2.2 Connector Summary
Summary Table
Nbr Description Type of Connections Pin nbrs.
J1 CF Master/Slave Switch
Slide Switch On/OFF
J3 USB External USB Connector 6-pin J4 USB External USB Connector 6-pin J5 USB (Touchscreen) 2.0mm 5-pin wafer 5-pin J8 PS/2 Keyboard 2.54mm 5-pin box header 5-pin J9 PS/2Keyboard/Mouse External Mini DIN Socket 6-pin
J10 COM2(RS232/422/485)
External D-Sub Male Connector 9-pin
J14 VGA 2.0mm 10-pin box header 10-pin J18 Micro SD Card Socket Micro SD socket J23 Audio Line-Out 1.25mm Phone Jack J24 Audio Mic-In 2.0mm 4-pin wafer 4-pin J25 COM3 (TX, RX) 1.25mm 3-pin wafer 3-pin J26 COM4 (TX, RX 1.25mm 3-pin wafer 3-pin J30 SOM CPU Board Socket
SOM CPU Board Socket 200-pin
J31 4-Wires Touch connector
1.25mm 4-pin wafer 4-pin
J32 USB (Wi-Fi Optional) Internal USB Connector 6-pin RJ45 Ethernet External RJ45 Connector 8-pin PWR Power Connector (5A) External Mini DIN Socket 3-pin PWR Power Connector (8A) External Power Plug 2-pin
CF1 CF Card Socket CF Type I/II Socket
Page 14
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
11
2.3 Connector Pin Assignments
J1: CF Master/Slave Switch
J3: USB
Pin # Signal Name Pin # Signal Name
1 VCC 2 USBD2­3 USBD2+ 4 GND 5 GND 6 GND
J4: USB
Pin # Signal Name Pin # Signal Name
1 VCC 2 USBD3­3 USBD3+ 4 GND 5 GND 6 GND
J5: USB (Option al)
Pin # Signal Name
1 VCC 2 USBD1­3 USBD1+ 4 GND 5 GND
J8: PS/2 Keyboard
Pin # Signal Name Pin # Signal Name
1 KBCLK 2 KBDAT 3 NC 4 GND 5 VCC
J9: PS/2 Keyboard/Mouse
Pin # Signal Name Pin # Signal Name
1 KBCLK 2 MSCLK
Pin # Signal Name
On Master
OFF Slave
Page 15
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
12
3 GND 4 KBDATA 5 MSDATA 6 VCC 7 GND 8 GND 9 GND
J10: COM1 RS232/422/485 (C hange setting by BIOS)
Pin # Signal Name Pin #
Signal Name
1 DCD1/ 422TX- / RS485- 2 RXD1 / 422TX+ / RS485+
3 TXD1 / 422RX+ 4 DTR1 / 422RX-
5 GND 6 DSR1
7 RTS1 8 CTS1
9 RI1
J14: VGA
Pin #
Signal
Name
Pin #
Signal
Name
1 R OUT 2 GND 3 G OUT 4 GND 5 B OUT 6 GND 7 HSYNC 8 GND 9 VSYNCD 10 GND
J24: MIC-IN
Pin # Signal Name
1 MICVREF 2 GND 3 GND 4 MIC-IN
J25: COM3 (TX, RX)
Pin # Signal Name
1 GND 2 TXD3 3 RXD3
Page 16
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
13
J26: COM4 (TX, RX)
Pin # Signal Name
1 GND 2 TXD4 3 RXD4
J31: 4-Wires Touch connector
Pin # Signal Name
1 Y­2 X­3 Y+ 4 X+
J32: USB (WiFi Optional)
Pin # Signal Name Pin # Signal Name
1 VCC 2 USBD2­3 USBD2+ 4 GND 5 GND 6 GND
PWR: Power Connector (5A)
Pin # Signal Name
1 +5V 2 GND 3 NC 4 GND
PWR: Power Connector (8A)
Pin # Signal Name
1 + 8 ~ 35V 2 GND
Page 17
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
14
2.4 External I/O Overview
(Note1: Wireless is optional) (Note2: COM1 RS232/422/485 is selected by BIOS setting)
PMX-089T-8A/ PMX-089T-8A-512
PMX-089T-5A/ PMX-089T-5A-512
Page 18
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
15
2.5 External I/O Pin Assignment
Power Switch
Pin # Status
| ON
O OFF
Power Connector (5A)
Pin #
Signal Name
1 +5V 2 GND 3 NC
Power Connector (8A)
Pin #
Signal Name
1 +8 ~ 35V 2 GND
J10: COM1 RS232/422/485 (C hange setting by BIOS)
Pin # Signal Name Pin # Signal Name
1
DCD1/422TX-/RS485-
2 RXD1/422TX+/RS485+
3
TXD1 / 422RX+ 4 DTR1 / 422RX-
5
GND 6 DSR1
7
RTS1 8 CTS1
9
RI1
Page 19
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
16
Audio Line-Out
Pin #
Signal
Name
1 GND 2 LOUTL 3 Open Touch 4 Open Touch 5 VREFOUT
USB
Pin # Signal Name
1 VCC 2 USB0­3 USB0+ 4 GND 5 GGND 6 GGND
RJ45
Pin # Signal Name Pin # Signal Name
1 FTXD+ 2 FTXD­3 FRXIN+ 4 NC 5 NC 6 FRXIN­7 NC 8 NC
PS/2 Keyboard/Mouse
Pin # Signal Na me
1 KBCLK 2 PMCLK 3 GND 4 KBDAT 5 PMDAT 6 SB5V
Page 20
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
17
2.6 System Mapping
Page 21
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
18
Page 22
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
19
Page 23
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
20
2.7 Watchdog Timer
There are two watchdog timers in PMX-089T, we also provide DOS, Linux and WinCE example
for your reference. For more technical support, please visit:
www.compactpc.com.tw
or download
the PDF file:http://www.compactpc.com.tw
Page 24
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
21
C h a p t e r 3
Driver Installation
VGA
The Vortex86MX processor is integrated RDC Display chip which is an ultra low powered
graphics chipset with total power consumption at around 1-1.5 W.
LAN
The Vortex86MX processor is integrated 10/100Mbps Ethernet controller that supports both 10/100BASE-T and allows direct connection to your 10/100Mbps Ethernet based Local Area Network for full interaction with local servers, wide area networks such as the Internet. I/O and IRQ settings can be done by software with the supplied utility software, or it can be set for Plug and Play compatibility. The controller supports: Half / Full-Duplex Ethernet function to double channel bandwidth, auto media detection.
AUDIO
The ALC262 series are 4-Channel High Definition Audio Codecs with UAA (Universal Audio Architecture) featuring two 24-bit stereo DACs and three 20-bit stereo ADCs, they are designed for high performance multimedia desktop and laptop systems. The ALC262 series incorporates proprietary converter technology to achieve over 100dB Signal-to-Noise ratio playback quality; easily meeting PC2001 requirements and also bringing PC sound quality closer to consumer electronic devices.
Operating system support
The PMX-089T provides the VGA and LAN drivers for Linux, Windows CE, Windows XP
Professional, and Windows Embedded standard (XPE). (Linux can use with Compact Flash
card only.)
Please get the drivers from
DMP official website:
www.compactpc.com.tw
.
PMX-089T also supports most of the popular Linux distributions, for more detail information, please visit DMP official website:
http://www.dmp.com.tw/tech/vortex86dx/
Page 25
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
22
3.1. PMX-089T Development Note
<Primary /Secondary IDE: Master or Slave>
Micro SD: Primary Master
CF Slot: Secondary IDE: Master or Slave (User can use slide switch (in side of CF slot) to adjust Master or Slave
<Window CE6.0 development guide>
Windows Embedded CE 6.0 BSP, trial CE image and development notes, please visit technical website to get more information:
www.compactpc.com.tw
<Linux installation note>
Please forced the IDE setting in BIOS to PIO mode before install Linux on PMX-089T as follows: 1-Go to the advanced BIOS setting and make the “Onboard IDE Operate Mode” is
“Legacy Mode” 2-Go to the PCI/PnP and make the “PCI IDE BusMaster” is “Disable"
< XP professional /Home /Embedded and Windows 2000 installation note >
1-Please visit technical website to get more information:
www.compactpc.com.tw
<Enhance CF to run the UD MA2/4>
1-Please select
DMP “ICF Card” to supporting UDMA 2/4 Mode.
<How to b oot up from the Micro SD card>
1-Get into the BIOS setup Utility
2-Go to the Advanced 3-Choose Primary IDE Pin Select: SD card 4-Press “F10” to save configuration changes and exit setup
Page 26
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
23
3.2. BIOS Default setting
If the system cannot be booted after BIOS changes are made, Please follow below procedures in
order to restore the CMOS as default setting.
Press “End” Key, when the power on
Press <Del> to enter the AMI BIOS setup Press “F9” to Load Optimized Defaults Press “F10” to Save configuration changes and exit setup
Page 27
PMX-089T DM&P Vortex86MX Panel PC with 8.9” WSVGA TFT LCD
24
Warranty
This product is warranted to be in good working order for a period of one year from the date of purchase. Should this product fail to be in good working order at any time during this period, we will, at our option, replace or repair it at no additional charge except as set forth in the following terms. This warranty does not apply to products damaged by misuse, modifications, accident or disaster. Vendor assumes no liability for any damages, lost profits, lost savings or any other incidental or consequential damage resulting from the use, misuse of, originality to use this product. Vendor will not be liable for any claim made by any other related party. Return authorization must be obtained from the vendor before returned merchandise will be accepted. Authorization can be obtained by calling or faxing the vendor and requesting a Return Merchandise Authorization (RMA) number. Returned goods should always be accompanied by a clear
problem description.
Loading...