D-MAX DSC-2000Si, DSC-2000Se User Manual

Download

USER MANUAL

HIGH SPEED DOME CAMERA

1. CAUTION -------------------------------------------------------------------------------- 2

2. INTRODUCTION OF PRODUCT 4

1). DESCRIPTION AND FEATURES --------------------------------------------- 4

2). INSTALLATION AND CONNECTION ---------------------------------------- 5

2-1. NAME AND FUNCTION OF EACH PART ----------------------------- 5

2-2. INSTALLATION -------------------------------------------------------------- 6

2-3. BASIC CONNECTION ----------------------------------------------------- 8

2-4. CONNECTION DIAGRAM ------------------------------------------------ 9

3. DIRECTIONS FOR USE 10

1). DIP SWITCH SETTING ---------------------------------------------------------- 10

2). HOW TO CHANGE PROTOCOL ---------------------------------------------- 11

3). SETTING ADDRESS OF DIP SWITCHES ---------------------------------- 12

4). HOW TO USE OSD MENU ----------------------------------------------------- 13

4-1. HOW TO CONTROL OSD MENU --------------------------------------- 13

4-2. FUNCTIONAL DESCRIPTIONS ON EACH MENU ----------------- 14

4-3. FUNCTIONAL SETTING, OPERATION/DELETION THE

KEYBOARD-------------------------------------------------------------------

4-4. OSD MESSAGE DESCRIPTION ---------------------------------------- 29

4 TROUBLE SHOOTING --------------------------------------------------------------- 31

5 DIMENSION --------------------------------------------------------------------------- 32

6 ASSEMBLY --------------------------------------------------------------------------- 34

7 SPECIFICATION -------------------------------------------------------------------- 42

Table of contents

Thank you for purchasing our product. Please operate the product after being

fully aware of the manual.

Pease contact us if you have any queries.

Precaution

Note the following matters before the installation of the product.

Avoid the following places for the installation.

1.CAUTION

A high/low temperature: Using indoor-cameras

in the places of +50°C~ -10°C can cause

troubles and lower its capacity.

Snow, rain and wet: Humidity or water and

any liquid inside-camera can cause troubles.

Oil, gas: Oil and gas can damage the camera

as they go through the cameras.

Vibration, shock: They bring on problems or

errors of the camera.

Direct light, exposure to the air: In the case of

that sets indoor- cameras outside where the

weather is changeable, it can cause problems.

Closing to High frequency and electric power

lines: Setting the camera up around

electromagnetic units or power supplier can

cause problems.

Caution in Use

Do not disassemble the unit and put alien substances in the unit.

- Disassembling the unit or putting alien substances such as a metal can make the

camera defective.

- Make sure of power switch-off before the installation.

: Ensure power switch-off and check the voltage the camera before the installation.

- Do not give the unit a shock and an operation.

: Giving a strong shock or an excessive power on the button, terminal can cause

problem.

This product has been designed and manufactured in accordance with the harmonized

European standards, following the provisions of the below stated directives.

Electromagnetic Compatibility Directive 89/336/EEC

(EN60065:1998, EN61000-6-3:2001, EN61000-6-1:1997)

This devise complies with part 15 of the FCC rules operation is subject to the

following two conditions: (1) This device may not cause harmful interference and

(2) This device must accept any interference received including interference that

may cause undesired operation

1) DESCRIPTION AND FEATURES

This camera has been designed elegantly for buildings, department stores that

need to be in harmony with the interior as a high speed dome camera, including

various observation functions.

2. INTRODUCTION OF PRODUCT

☺ 30x Zoom lens

30x Optical zoom lens combined with an auto focus

system and digital zoom enable you to get maximum

300x great pictures.

☺ A low light function

Surveillance with optimum picture is possible owing

to digital-slow-shutter function.

Digital-slow-shutter function is improving the CCD

sensitivity by electrically lengthening exposure time

so that it should be under surveillance on the

condition of 0.0007 Lux in B/W.

☺ Various auto-surveillance functions

z PTZ trace

Track the registered manual operation for about 180

seconds.

z Auto swing

Repeat pan and tilt between two preset positions.

z Group sequence

12 Preset positions are chained in one Group.

z Tour sequence

Max 12 Groups are bound.

☺ 250 Preset positions

A maximum of 250 preset positions can be

programmed. The preset function enables to set

where you want on monitor at any time.

☺ Smart pan/tilt function

z It should be rotated pan travel by 360° endless. z Pan and tilt speed compensation function in proportion to

depth of zoom.

☺ Day & Night function with filter

z It allows to make surveillance in the night or low

illumination condition with motorized IR cut filter

system. (0.1 Lux)

z In the darkness, it should be changed to black &

white mode automatically.

z With DSS control, it allows watching on 0.0007

Lux.

☺ 8ch alarm inputs

It can be directly connected to sensor and used with

presets owing to built-in 8-channel sensor input

terminals. It can be also operated together with

other equipment owing to built-in alarm output. (2-

Relay normal output)

☺ Auto flip function

The unit can track the moving object automatically

until 180° in vertical by using controller.

☺ 16 Privacy Masking Zones

For the privacy, it can be programmed for masking

zone up to 16 locations on the OSD menu screen.

☺ OSD (On Screen Display) Menu

Provides character information displayed on the

monitor, such as the camera ID address, camera

name, preset number, sequence status, and sets

various functions of camera easily on the OSD

menu screen.

2) INSTALLATION AND CONNECTION

2-1. Name and function of each part

Connect it

with cover

housing or

bottom cover,

then combine

with bracket.

It protects inside

the camera, and

built-in pan

makes the heat

cool when using

of long time.

It is a part to be

connected with power,

video, data.

It is a part to set

Dip switch.

It combines with cover housing,

and the bubble rubber is useful

for the water proof outdoors

It is a bubble

cover for indoor

camera

INDOOR TYPE OUTDOOR TYPE

2-2. Installation

Open the cover with unscrewing 5 bolts, then

separate the camera body from the cover

housing with turning it as the same direction in

the picture

(the bolt of the bubble cover is not separated

completely)

Unlock the device of the bottom cover, then

separate the camera body cover from the

bottom cover with turning it as the same

direction in the picture.

INDOOR TYPE OUTOOR TYPE

LOCK DEVICE :

Check the direction when it connects

with camera body case,

And lock it with DSC-1000Si

AC24V INPUT

Use AC24V power and

use either terminal

power connect or jack

power connect.

POWER LED :

Power LED is turned

when the power is ON

DATA IN ( RS-485) :

Never connect the power into

here.

It is cause of a breakdown

2-3. Basic Connection

Connect the video line of a

monitor

DC12V 1A adaptor and junction box are

provided on a purchase. Junction box

consists of 2 data ports (each data port

can be connected with maximum up to

128 cameras and sub keyboard terminal.

User can control maximum up to 255

cameras connected by using the

exclusive control keyboard.

User can connect it maximum up to

1.2km when using twist pair shield

cable as a connecting cable.

2-4. Connection diagram

Must use AC24V power source. The current value must be 1.5A

or more and use a double winding transformer.

Alarm output is tangency output of

relay non-load. It can be used up to AC

220V/10A by connecting with the load.

The switch is automatically turned on

when the sensor works and it is

possible to cancel by using the

controller after the regular time

The sensor

Can be connected up to 8 channels and the

camera can be moved automatically to the

point by preset mode, if there is any

problems

DATA

Can be processed by RS 485 and connected in

parallel to use a large quantity of cameras.

1). DIP SWITCH SETTING

Set the camera numbers in the state of

ADDR, set communication speed, protocol

in the state of INIT.

This part is each address of camera.

-Termination Resistor (DIP SW NO1)

-Turn the last camera on the data line as a switch

to turn on/off the terminal resistor on. Turn the

DIP SW of some of the farthest cameras on in the

case of the data lines distributed to

* The first

default is off.

-RS485RS422 SELECT (DIP SW NO2)

-Turn on or off for the suitable data system

between RS485 and RS422.

* The first default is off.

-Address /Initial select (DIP SW NO3)

-Set the DIP SW up in the ADDRESS.

*The first default is ADDRESS.

-Set the communication speed and Protocol

(Demand for the technical

inquiry) up in the

state of the INITAIL.

-Internal/External (DIP SW NO5)

-Use it when selecting Internal and external.

* The first default is INTERNAL

3. DIRECIONS FOR USE

2) HOW TO SET PROTOCOL

Change No.3 at S2 to INIT if user wants to change Protocol.

① Please the power off.

② Switch on the Protocol that you want to change on as above table.

③ The power on, then the set Protocol and Baud rate are appeared.

④ The power off, if every setting is right. Then the change of Protocol is finished.

⑤ Change No.3 at S2 to ADDR before the power on, then the power on after setting the address of

the camera.

⑥ Try it again with the information as above the table, if something is wrong.

Set this part up Do not necessary to set it up

The switch to select baud rate The switch to select protocol

3) SETTING ADDRESS OF DIP SWITCHES.

Use DIP switches No.1 to No.8 for address, it can be set 1 program to 255 program.

DIP SWITCH (HEX) DIP SWITCH (HEX) RX

1 2 3 4 5 6 7

1 ON OFF OFF OFF OFF OFF OFF 33 ON OFF OFF OFF OFF ON OFF

2 OFF ON OFF OFF OFF OFF OFF 34 OFF ON OFF OFF OFF ON OFF

3 ON ON OFF OFF OFF OFF OFF 35 ON ON OFF OFF OFF ON OFF

4 OFF OFF ON OFF OFF OFF OFF 36 OFF OFF ON OFF OFF ON OFF

5 ON OFF ON OFF OFF OFF OFF 37 ON OFF ON OFF OFF ON OFF

6 OFF ON ON OFF OFF OFF OFF 38 OFF ON ON OFF OFF ON OFF

7 ON ON ON OFF OFF OFF OFF 39 ON ON ON OFF OFF ON OFF

8 OFF OFF OFF ON OFF OFF OFF 40 OFF OFF OFF ON OFF ON OFF

9 ON OFF OFF ON OFF OFF OFF 41 ON OFF OFF ON OFF ON OFF

10 OFF ON OFF ON OFF OFF OFF 42 OFF ON OFF ON OFF ON OFF

11 ON ON OFF ON OFF OFF OFF 43 ON ON OFF ON OFF ON OFF

12 OFF OFF ON ON OFF OFF OFF 44 OFF OFF ON ON OFF ON OFF

13 ON OFF ON ON OFF OFF OFF 45 ON OFF ON ON OFF ON OFF

14 OFF ON ON ON OFF OFF OFF 46 OFF ON ON ON OFF ON OFF

15 ON ON ON ON OFF OFF OFF 47 ON ON ON ON OFF ON OFF

16 OFF OFF OFF OFF ON OFF OFF 48 OFF OFF OFF OFF ON ON OFF

17 ON OFF OFF OFF ON OFF OFF 49 ON OFF OFF OFF ON ON OFF

18 OFF ON OFF OFF ON OFF OFF 50 OFF ON OFF OFF ON ON OFF

19 ON ON OFF OFF ON OFF OFF 51 ON ON OFF OFF ON ON OFF

20 OFF OFF ON OFF ON OFF OFF 52 OFF OFF ON OFF ON ON OFF

21 ON OFF ON OFF ON OFF OFF 53 ON OFF ON OFF ON ON OFF

22 OFF ON ON OFF ON OFF OFF 54 OFF ON ON OFF ON ON OFF

23 ON ON ON OFF ON OFF OFF 55 ON ON ON OFF ON ON OFF

24 OFF OFF OFF ON ON OFF OFF 56 OFF OFF OFF ON ON ON OFF

25 ON OFF OFF ON ON OFF OFF 57 ON OFF OFF ON ON ON OFF

26 OFF ON OFF ON ON OFF OFF 58 OFF ON OFF ON ON ON OFF

27 ON ON OFF ON ON OFF OFF 59 ON ON OFF ON ON ON OFF

28 OFF OFF ON ON ON OFF OFF 60 OFF OFF ON ON ON ON OFF

29 ON OFF ON ON ON OFF OFF 61 ON OFF ON ON ON ON OFF

30 OFF ON ON ON ON OFF OFF 62 OFF ON ON ON ON ON OFF

31 ON ON ON ON ON OFF OFF 63 ON ON ON ON ON ON OFF

32 OFF OFF OFF OFF OFF ON OFF 64 OFF OFF OFF OFF OFF OFF ON

-No.1 is changed to No.64 and the last No.64 is changed No.128 when No.7 DIP SW is on.

-No.1 is changed to No.129 when No.7 DIP SW is off and No.8 DIP SW is on.

-No.1 is changed to No.193 and user can set up to maximum 255 ADDRESS when No.7, 8 DIP SW are on.

4) HOW TO USE OSD MENU

4-1. How to control OSD menu

● OSD (ON SCREEN DISPLAY) CONTROL

It is the function to call up the Menu

＊User can not only set Preset, Group, Tour, Swing, Trace functions of the camera up by the menu, but also set

them up by shortening keys. (Refer to 3-3 content)

● Accessing OSD MENU

(1) The menu is displayed on the screen with the key tone when user presses No.1 and menu key.

● OSD Menu Control.

Right and Left

moving of Cursor

Feed letters into system.

Selection of up and

down menu

Change of setting.

● Cancellation of OSD MENU

4-2. Functional Descriptions of each Menu.

1. ID SET.

It is the function to set ID of the camera.

Move to No.1 menu and the screen moves as following when user

presses F/F key.

User can choose letters that they want, if user control a joystick up

/ down / right / left, and user can reselect the previous letters, if

user presses Z/I, Z/O or turn the head of the joystick to right/left.

“•” is not displayed on the screen as a blank letter,

user can input letters in Japanese and in Chinese

If user moves the joystick down continuously.

2. OSD DISPLAY.

Set up whether user sets ID and STATUS to display on the

screen in normal operating.

● ID + Status: ‘ID’ and ‘Status’ displayed on the screen

● ID only: Only ‘ID’ displayed on the screen

● Status only: Only ‘Status’ displayed on the screen

● All off: Nothing displayed on the screen

3. BACK LIGHT

Set up backlight compensation mode.

● On: It compensates a dark subject to a light subject by

BACK LIGHT function.

● Off: Cancellation of BACK LIGHT compensation mode.

4. AGC LEVEL

AGC(Automatic Gain Control)- It adjusts the amount of video

amplification to maintain a full 1-volt peak-to-peak video signal

output automatically.

▶ Range : Auto, 8Db, 10Db, ----- 38dB

5. SHUTTER SPEED

As a setting shutter speed mode, it can be distinguished a fast

moving subject easily by means of shutter speed up.

※Attention-The illumination of the camera decreases if shutter

speed is up.

※The state of first default is ‘AUTO’.

※It can be worked in the state of Flickerless ‘off’

▶ Range : Auto, 1/125, 1/150, 1/200, --- 1/10000

6. SHARPNESS LEVEL

Compensation of the shape of a subject

▶ Range : 0 ~ 14, Default : 10

7. BRIGHTNESS

Control brightness of a screen.

The screen gets dark because an iris is closed as the numerical

value is low, whereas the screen gets bright because an iris

is opened as the numerical value is high.

▶ Range: 0~99, Default: 50

8. FLICKERLESS

Tremble on the screen is removed in the state of FLICKERLESS

‘ON’, the shutter speed, at the same time, is fixed in 1/120sec in

NTSC and in 1/100sec in PAL.

※Move the joystick down then choose “NEXT MENU PAGE” on

the screen to move next page.

9. SSNR level

It can remarkably reduce noise of minimum illumination by super

noise removable technique and also file size becomes smaller

while DVR is being recorded by the effective reduction of noise.

▶ Off, Low, Middle, High

10. WHITE BALANCE

It prevents from that white color is changed as illumination, user

can set it up in 2 ways.

▶ Indoor, Outdoor

11. FOCUS MODE

Change Focus Mode to hand-worked or auto.

▶ OneShot : Auto Focusing mode works during non-working

after zoom is worked.

▶ Auto : It adjusts the focus automatically as it monitors the

screen.

▶ Manual : User can control the focus by hand-worked.

12. ZOOM MAX Limit

It is used when user corrects and limits the extensional range

of the focus as a function to set the maximum value of zoom.

▶ Off, 60X ~ 300X

The camera is reset when user is out of Menu mode after end

the setting, and the changed magnification is registered in

the camera

13. DSS CONTROL

An object becomes clear as the field value gets higher in

illumination, whereas a moving object becomes dim.

▶ Range : Off, 2 ~ 1 128 fields

14. DAY& NIGHT

The function is used to distinguish an object clearly in the dark

condition.

▶ Auto : DAY & NIGHT mode is worked automatically,

if it is dark.

▶ On : Change into DAY & NIGHTY mode by hand-worked

▶ Off : Set DAY & NIGHTY mode ‘off’

15. STABILIZ On/Off

There is some tremble as zoom magnification is high, the function

can compensate the tremble.

▶ On / Off

16. Motion Detection

Set Motion ‘On’ after move the camera where user wants.

It displays the message ‘Motion Detected’ on the screen

when the moving of an object is sensed on the same screen.

17. PRESET SET & RUN PAGE

It is a function to set and operate Preset, Group, Tour.

User can see the screen when moves the joystick to Right/Left

after fixing the cursor on the menu.

<<PRESET SETUP PAGE>>

① Preset set CH :

User can set Preset No. and title on this menu.

- Preset No. set : Set it by moving the joystick to Right/Left

- Preset title set : User can see the menu “SET ID” when

presses F/F key after setting Preset No.

※The setting steps are the same as “ID Set” at page 14

② Preset PTZ set : Set the position of Preset.

Select the main menu with the joystick, then press

F/F key for next page. Select [SAVE] with F/N key

after setting the Preset point by using the joystick

and. In/Out function, then the data is saved if user presses F/F key, then it is

moved to the previous screen automatically from the menu.

※ Repeat the same way after changing the number of Preset, if user set another Preset.

③ Preset Swing SET : Set Preset Swing.

Move next SWING page for the setting, if user

presses F/F key in the state of selection of the menu

※The preset must be set before the setting as Swing

Is a function to repeat an auto observation of 2 Preset

points user fixes in Preset set

•[SAVE]: Previous screen. [DELETE]: Remove. [ESC]: Cancel

④ GROUP SET: User can set maximum 12 groups.

Select a channel then move to next page after

pressing F/F key

※The Preset point in the Group that 12 Preset

points are set is observed repeatedly and order

with regular speed and time.

⑤ Tour SET Group: User can set continual Group

motion that can be put 12 Groups in 1 Tour

Move to the setting page if user presses F/F key

on this menu

■ The Group user wants to set must be set firstly

※Setting is only possible when Preset is set first

in the state of setting of Swing, Group, Tour,

otherwise, it displays the message “Sorry Undefined”.

⑥ Run Function: Operate one of SWING/ ＊Set / Stop order with a control keyboard without menu

GROUP / TOUR / TRACE. (It is operated on the screen. automatically after end of OSD menu)

■ User can look at how to set TRACE at “18. TRACE SET PAGE”

⑦ RETURN MENU PAGE: Move to a higher menu page when control the joystick Right/Left in the

Set the value of “00” part of T01~T12 to Group

channel that User wants, then the setting is saved

when user is out of the menu after pressing F/F key

Selection of this menu.

18. TRACE SET PAGE

Set TRACE.

User can regenerate and save a change of the unrestricted

location of ZOOM In/Out and a position of the camera by

hand-worked control with a joystick.

User can see the screen when moves the joystick to Right/Left

after fixing the cursor on the menu

■ How to set TRACE

Move to [SET] after pressing

Check – Control scenes that user wants by hand-

worked with a joystick after the message.

“Set Trace: OO%” on the middle of the screen. If user finishes

this part, Move to [SAVE] with

It goes a higher menu after being saved data if user presses

with a display of the message “Save TRACE”

19. ALRAM CHANNEL ON/OFF

- CH On/Off : Alarm Input – Each channel can be ON/OFF

- Alarm Relay : It can be set On or not when ALARM OUTOUT

PORT operate wrong.

- Active Alarm : It selects ACTIVE OPEN or ACTIVE CLOSE

by tangency when something is wrong. It is ACTIVE when

ALARM INPUT is OPEN in ACTIVE OPEN, it is ACTIVE

when ALARM INPUT is CLOSE in ACTIVE CLOSE.

- Resume Time Set :

It can select the delay time that the camera move to the place alarming to observe where wrong signal is sensed.

User can set it for 1sec to 180sec and operate GROUP, TOUR, SWING again in a preset time.

SWING, GROUP, TOUR are operated in a preset time when user stops the operating joystick in the case of not

connecting with the ALARM.

Press SWING, GROUP, TOUR keys without stopping of the joystick to stop the operating completely

(*Stopping the operating with the joystick affects the SET function.)

20. ALARM PRESET SET PAGE

■ The camera can move to a preset point automatically when

something is wrong in each ALRAM CHANNEL.

■ Set a preset point firstly to move if anything wrong, then use

that sets the preset number into each ALARM CHANNEL.

■ PRESET is out of connecting in ALARM CHANNEL No.“0”

■ User can select PRESET number 1 to 250 and set it.

■ Home Position Preset

The camera automatically moves to where master user set

when another user controls the camera to observe other area.

(You can set 1~250 points)

■ Home Position Time

It sets the dwell time in Home Position Preset.

It automatically moves to where observes ordinarily in the

regular time that Master user set in observation of other area

,if set Home Position Preset

(You can set 1~180sec. Set control Home Position Preset

and Home Position Time together for using this function.)

※You can set ALARM setting MENU not only in CAMERA

SET MENU MODE, but also a KEYBOARD in direct

21. PRIVARCY ZONE SET

Max

16 privacy zones can be configured for the protection of

privacy.

■ How to set privacy zone

In <<PRIVACY ZONE SET>> menu, select the channel that

you want by a joystick, then move to the next page if you

press the

[F/F] key

①

Select a Channel

④ Fix the black square on the middle of area that you want to

hide by a joystick, then go back to the previous page by [F/F] key after controlling the size of the square by [Z/I], [Z/O] key and saving it.

Set the position BOX Extension / Reduction Check

⑤ The Channel is changed BLANK to ‘OFF’.

The screen displays the black square, if you change the CH ON’ as the left picture.

Move to the Channel Change the CH ‘ON’ Check

⑥ Out of OSD MENU

22. AUTO TILT MOVE

The PAN is turned in a 180° degree arc automatically when the

angle of the camera moves down to the maximum degree,

therefore, it is possible to track objects continuously.

23. SMART PANTILT

It is a function that P/T speed is getting slower as Zoom in.

It is hard to observe objects with the high PANTILT speed in

operating of Zoon In

This function makes the speed less automatically for the

effective observation

24. manual P/T SPEED

User can control the maximum speed in controlling of up and

down.

It can be set Low, Medium, Max and one turn (360°/sec) is

possible in Max.

25. LANGUAGE

English, Portugu-, Polosh

26. FACTORY RESET WARNING

Please be careful of that all setting data of OSD MENU are

reset into the first default when operates FACTORY RESET

WARNING.

The setting data of Preset, Swing, Group, Tour, Trace, also is

deleted all.

4-3. Functional Setting, Operating/Deletion by the Keyboard

1. Preset setting

You can set Preset point up to 250.

Preset Input.①

Preset setting can be set 1 to 250 sequentially after

moves the camera to where you want

② Preset Move

The camera moves to the preset point, if you press

Preset No. that you want and P-SET Key

③ Delete a separate Preset

Go on in order as below when the sound is heard Ex) Delete 5

Preset

in 3 seconds after pressing CLR Key

(Waiting for 3seconds)

④ Delete all Preset

Go on in order as the right picture when the sound is heard

in 3 seconds after pressing CLR KEY (Waiting for 3seconds)

2. Swing setting

① Swing Input

Tilt setting

Pan setting

Starting Preset

Ending Preset No

Set the delay time (1~127sec)

Set the move speed (1~64 steps)

② Operation of Swing ③ End of Swing

(Run Pan) (Run Tilt)

3. Group setting

① Start Group setting mode

- Set Preset No. again if you want to input it continuously.

- Set a GROUP again from the first after ending with SET Key , if you want to finish Preset input in one

Group to input next Group.

② Start a Group ③ Stop the Group

You can stop it when pressing Group key or using a joystick

4. Tour setting

① Tour set mode

Start the Tour set mode Select a Group in 1 ~ 12

Start the Group

setting mode

Select in Preset No.1~250

and input them.

Select the Group in 1~12

Move Speed: The Speed from A to B 64=High, 1=Low

Dwell Time: The dwell time at the point of A or B before the move. (sec)

■ Repeat input in continual input

EX). Register Group No. 1,3,6 as Tour

② Start / End Tour ③ Delete Tour

Start Tour Finish Tour

5. Spiral Function

It is a function to observe objects in the spiral direction.

① Spiral observation ‘ON’ ② End

6. PTZ Trace

It memorizes P/T/Z motions for 200sec, then operates them at the same Trace.

① Start / End Trace

② Set Trace ③ Delete Trace

Tour No.1

Tour No.3

Finish

Tour mode

Start

Tour mode

Tour No.2

4-4. OSD MESSAGE DISCRIPTION

4. TROUBLE SHOOTING

5. DIMENSION

Wall mount bracket

Ceiling mount bracket

In-ceiling mount bracket

Unscrew the 5bolts from the Bubble cover①

and open it, then separate the Camera body

from the Cover housing.

(The bolts from the Bubble cover are not

separated completely.)

②Connect each cables, then screw 4 bolts.

Block up beside the hole with 34mm BLANK RUBBER

③In set of it on the concrete, connect the cables as

above the picture and join TAB/P1/11” flexible

connector(28Ø)

④Connect the Cover housing with Wall bracket as

Above the picture.

6. ASSEMBLY

DSC-30EWP Wall mount bracket

Connect the Hous⑥ ing with the camera body.

Please check the triangular mark on the side

of the body and inside.

⑦Connect the Bubble again.

⑤Connect the Data, Video, Power cables.

(Refer to page 7)

Unscrew the 5bolts from the Bubble cover①

and open it, then separate the Camera body

from the Cover housing.

(The bolts from the Bubble cover are not

separated completely.)

②Fix the Pole box from the ceiling.

⑤Turn the Cover housing tight.

DSC-20ECP Wall mount bracket

Connect the Data, Video, Power⑥

cables. (Reference to Installation

and Connection.)

⑦Connect the Housing with the camera body.

Please check the triangular mark on the side

of the body and inside.

⑧Connect the Bubble again.

Ceiling bracket is used as In/Outdoor type

and you can remove or extend the Ceiling

pole to fix the length. It is manufactured

as a standard size by our-self.

Ceiling Adhesion bracket

Set sub keyboard

Set one main keyboard

MODEL DSC-2000Si (Indoor )

Signal system NTSC PAL

Image sensor 1/4” Sony HAD CCD

Effective pixels 768(H) X 494(V), 752(H) X 582(V),

Horizontal resolution More than 520 TVL, B/W 570 TVL

Lens 30x Optical zoom, f =3.3 –99mm

Digital zoom 10x (Total zoom 300x)

Angle of view Approx 58.17° (Wide), Approx 2.2° (Tele),

Minimum illumination 0.7 Lux , 0.1Lux(D&N), Min 0.0007Lux(DSS),/F1.6

Luminance S/N ratio More than 50dB

Video output 1 Vp-p Composite video output 75Ω

Focus mode Auto / Manual / Oneshot

SSNR Off / Low / Middle / High

Back Light Off / Low / Middle / High

Shutter speed Auto / 1/120 ~ 1/60,000 sec

Sharpness control Level (0 – 10)

Stabilizer On/Off

Alarm in/out 8 Inputs / 2 Relay Output

Pan/Tilt angle

360° Endless / 92°

Pan speed

0.1° ~ 240°/sec (64 Levels)

Preset point 250 Presets

Preset Speed

Max 360°/sec (64 Levels)

Privacy zones masking 16 Zones

Operating temperature

- 10°C ~ 50°C (-14°F ~ 122°F)

Communiction system RS-485 / 422

OSD Built-in

Operating humidity Less than 90%RH

Dimensions 155.6mm(Diameter) x 223.6Height) mm

Weight About 3.1Kg ( Without adaptor )

Construction ABS body , Clear vandal bubble (PC)

Power consumption 18W (Max)

Power supply AC24V, 60/50 Hz

6. SPECIFICATION

※ The content of the manual is changeable to improve the quality.

MODEL DSC-2000Se ( Outdoor )