USER MANUAL
HIGH SPEED DOME CAMERA
600 TVL
2
1. CAUTION -------------------------------------------------------------------------------- 2
2. INTRODUCTION OF PRODUCT 4
1). DESCRIPTION AND FEATURES --------------------------------------------- 4
2). INSTALLATION AND CONNECTION ---------------------------------------- 5
2-1. NAME AND FUNCTION OF EACH PART ----------------------------- 5
2-2. INSTALLATION -------------------------------------------------------------- 6
2-3. BASIC CONNECTION ----------------------------------------------------- 8
2-4. CONNECTION DIAGRAM ------------------------------------------------ 9
3. DIRECTIONS FOR USE 10
1). DIP SWITCH SETTING ---------------------------------------------------------- 10
2). HOW TO CHANGE PROTOCOL ---------------------------------------------- 11
3). SETTING ADDRESS OF DIP SWITCHES ---------------------------------- 12
4). HOW TO USE OSD MENU ----------------------------------------------------- 13
4-1. HOW TO CONTROL OSD MENU --------------------------------------- 13
4-2. FUNCTIONAL DESCRIPTIONS ON EACH MENU ----------------- 14
4-3. FUNCTIONAL SETTING, OPERATION/DELETION THE ---------
KEYBOARD-------------------------------------------------------------------
27
4-4. OSD MESSAGE DESCRIPTION ---------------------------------------- 30
4 TROUBLE SHOOTING --------------------------------------------------------------- 32
5 DIMENSION --------------------------------------------------------------------------- 33
6 ASSEMBLY --------------------------------------------------------------------------- 35
7 SPECIFICATION -------------------------------------------------------------------- 43
Table of contents
2
Thank you for purchasing our product. Please operate the product after being
fully aware of the manual.
Pease contact us if you have any queries.
Precaution
Note the following matters before the installation of the product.
Avoid the following places for the installation.
1.CAUTION
A high/low temperature: Using indoor-cameras
in the places of +50°C~ -10°C can cause
troubles and lower its capacity.
Snow, rain and wet: Humidity or water and
any liquid inside-camera can cause troubles.
Oil, gas: Oil and gas can damage the camera
as they go through the cameras.
Vibration, shock: They bring on problems or
errors of the camera.
Direct light, exposure to the air: In the case of
that sets indoor- cameras outside where the
weather is changeable, it can cause problems.
Closing to High frequency and electric power
lines: Setting the camera up around
electromagnetic units or power supplier can
cause problems.
3
Caution in Use
Do not disassemble the unit and put alien substances in the unit.
- Disassembling the unit or putting alien substances such as a metal can make the
camera defective.
- Make sure of power switch-off before the installation.
: Ensure power switch-off and check the voltage the camera before the installation.
- Do not give the unit a shock and an operation.
: Giving a strong shock or an excessive power on the button, terminal can cause
problem.
This product has been designed and manufactured in accordance with the harmonized
European standards, following the provisions of the below stated directives.
Electromagnetic Compatibility Directive 89/336/EEC
(EN60065:1998, EN61000-6-3:2001, EN61000-6-1:1997)
This devise complies with part 15 of the FCC rules operation is subject to the
following two conditions: (1) This device may not cause harmful interference and
(2) This device must accept any interference received including interference that
may cause undesired operation
4
1) DESCRIPTION AND FEATURES
This camera has been designed elegantly for buildings, department stores that
need to be in harmony with the interior as a high speed dome camera, including
various observation functions.
2. INTRODUCTION OF PRODUCT
☺ High Resolution and Zoom late
High resolution 600 TVL and Built-in High Zoom
( 27X,33X, 37X )Rate Camera with 16x Digital Zoom
☺ A low light function
Surveillance with optimum picture is possible owing
to digital-slow-shutter function.
Digital-slow-shutter function is improving the CCD
sensitivity by electrically lengthening exposure time
so that it should be under surveillance on the
condition of 0.00004 Lux in B/W.
☺ Various auto-surveillance functions
z PTZ trace
Track the registered manual operation for about 180
seconds.
z Auto swing
Repeat pan and tilt between two preset positions.
z Group sequence
12 Preset positions are chained in one Group.
z Tour sequence
Max 12 Groups are bound.
☺ 250 Preset positions
A maximum of 250 preset positions can be
programmed. The preset function enables to set
where you want on monitor at any time.
☺ Smart pan/tilt function
z It should be rotated pan travel by 360° endless.
z Pan and tilt speed compensation function in proportion to
depth of zoom.
☺ Day & Night function with filter
z It allows to make surveillance in the night or low
illumination condition with motorized IR cut filter
system. (0.1 Lux)
z In the darkness, it should be changed to black &
white mode automatically.
z With DSS control, it allows watching on 0.00004
Lux.
☺ 8ch alarm inputs
It can be directly connected to sensor and used with
presets owing to built-in 8-channel sensor input
terminals. It can be also operated together with
other equipment owing to built-in alarm output. (2-
Relay normal output)
☺ Auto flip function
The unit can track the moving object automatically
until 180° in vertical by using controller.
☺ 16 Privacy Masking Zones
For the privacy, it can be programmed for masking
zone up to 16 locations on the OSD menu screen.
☺ OSD (On Screen Display) Menu
Provides character information displayed on the
monitor, such as the camera ID address, camera
name, preset number, sequence status, and sets
various functions of camera easily on the OSD
menu screen.
☺ Wide Dynamic Range
Wide-dynamic-range function is possible to look at
object clearer in back light condition.
5
2) INSTALLATION AND CONNECTION
2-1. Name and function of each part
Connect it
with cover
housing or
bottom cover,
then combine
with bracket.
It protects inside
the camera, and
built-in pan
makes the heat
cool when using
of long time.
It is a part to be
connected with power,
video, data.
It is a part to set
Dip switch.
It combines with cover housing,
and the bubble rubber is useful
for the water proof outdoors
It is a bubble
cover for indoor
camera
INDOOR TYPE OUTDOOR TYPE
6
2-2. Installation
Open the cover with unscrewing 5 bolts, then
separate the camera body from the cover
housing with turning it as the same direction in
the picture
(the bolt of the bubble cover is not separated
completely)
Unlock the device of the bottom cover, then
separate the camera body cover from the
bottom cover with turning it as the same
direction in the picture.
INDOOR TYPE OUTOOR TYPE
7
LOCK DEVICE :
Check the direction when it connects
with camera body case,
And lock it with DSC-1000Si
AC24V INPUT
Use AC24V power and
use either terminal
power connect or jack
power connect.
POWER LED :
Power LED is turned
when the power is ON
DATA IN ( RS-485) :
Never connect the power into
here.
It is cause of a breakdown
8
2-3. Basic Connection
Connect the video line of a
monitor
DC12V 1A adaptor and junction box are
provided on a purchase. Junction box
consists of 2 data ports (each data port
can be connected with maximum up to
128 cameras and sub keyboard terminal.
User can control maximum up to 255
cameras connected by using the
exclusive control keyboard.
User can connect it maximum up to
1.2km when using twist pair shield
cable as a connecting cable.
9
2-4. Connection diagram
Must use AC24V power source. The current value must be 1.5A
or more and use a double winding transformer.
Alarm output is tangency output of
relay non-load. It can be used up to AC
220V/10A by connecting with the load.
The switch is automatically turned on
when the sensor works and it is
possible to cancel by using the
controller after the regular time
The sensor
Can be connected up to 8 channels and the
camera can be moved automatically to the
point by preset mode, if there is any
problems
DATA
Can be processed by RS 485 and connected in
parallel to use a large quantity of cameras.
10
1). DIP SWITCH SETTING
Set the camera numbers in the state of
ADDR, set communication speed, protocol
in the state of INIT.
This part is each address of camera.
-Termination Resistor (DIP SW NO1)
-Turn the last camera on the data line as a switch
to turn on/off the terminal resistor on. Turn the
DIP SW of some of the farthest cameras on in the
case of the data lines distributed to
* The first
default is off.
-RS485RS422 SELECT (DIP SW NO2)
-Turn on or off for the suitable data system
between RS485 and RS422.
* The first default is off.
-Address /Initial select (DIP SW NO3)
-Set the DIP SW up in the ADDRESS.
*The first default is ADDRESS.
-Set the communication speed and Protocol
(Demand for the technical
inquiry) up in the
state of the INITAIL.
-Internal/External (DIP SW NO5)
-Use it when selecting Internal and external.
* The first default is INTERNAL
3. DIRECIONS FOR USE
11
2) HOW TO SET PROTOCOL
Change No.3 at S2 to INIT if user wants to change Protocol.
① Please the power off.
② Switch on the Protocol that you want to change on as above table.
③ The power on, then the set Protocol and Baud rate are appeared.
④ The power off, if every setting is right. Then the change of Protocol is finished.
⑤ Change No.3 at S2 to ADDR before the power on, then the power on after setting the address of
the camera.
⑥ Try it again with the information as above the table, if something is wrong.
Set this part up Do not necessary to set it up
The switch to select baud rate The switch to select protocol
12
3) SETTING ADDRESS OF DIP SWITCHES.
Use DIP switches No.1 to No.8 for address, it can be set 1 program to 255 program.
RX
NO
DIP SWITCH (HEX)
RX
NO
DIP SWITCH (HEX)
1 2 3 4 5 6 7 1 2 3 4 5 6 7
1 ON OFF OFF OFF OFF OFF OFF 33 ON OFF OFF OFF OFF ON OFF
2 OFF ON OFF OFF OFF OFF OFF 34 OFF ON OFF OFF OFF ON OFF
3 ON ON OFF OFF OFF OFF OFF 35 ON ON OFF OFF OFF ON OFF
4 OFF OFF ON OFF OFF OFF OFF 36 OFF OFF ON OFF OFF ON OFF
5 ON OFF ON OFF OFF OFF OFF 37 ON OFF ON OFF OFF ON OFF
6 OFF ON ON OFF OFF OFF OFF 38 OFF ON ON OFF OFF ON OFF
7 ON ON ON OFF OFF OFF OFF 39 ON ON ON OFF OFF ON OFF
8 OFF OFF OFF ON OFF OFF OFF 40 OFF OFF OFF ON OFF ON OFF
9 ON OFF OFF ON OFF OFF OFF 41 ON OFF OFF ON OFF ON OFF
10 OFF ON OFF ON OFF OFF OFF 42 OFF ON OFF ON OFF ON OFF
11 ON ON OFF ON OFF OFF OFF 43 ON ON OFF ON OFF ON OFF
12 OFF OFF ON ON OFF OFF OFF 44 OFF OFF ON ON OFF ON OFF
13 ON OFF ON ON OFF OFF OFF 45 ON OFF ON ON OFF ON OFF
14 OFF ON ON ON OFF OFF OFF 46 OFF ON ON ON OFF ON OFF
15 ON ON ON ON OFF OFF OFF 47 ON ON ON ON OFF ON OFF
16 OFF OFF OFF OFF ON OFF OFF 48 OFF OFF OFF OFF ON ON OFF
17 ON OFF OFF OFF ON OFF OFF 49 ON OFF OFF OFF ON ON OFF
18 OFF ON OFF OFF ON OFF OFF 50 OFF ON OFF OFF ON ON OFF
19 ON ON OFF OFF ON OFF OFF 51 ON ON OFF OFF ON ON OFF
20 OFF OFF ON OFF ON OFF OFF 52 OFF OFF ON OFF ON ON OFF
21 ON OFF ON OFF ON OFF OFF 53 ON OFF ON OFF ON ON OFF
22 OFF ON ON OFF ON OFF OFF 54 OFF ON ON OFF ON ON OFF
23 ON ON ON OFF ON OFF OFF 55 ON ON ON OFF ON ON OFF
24 OFF OFF OFF ON ON OFF OFF 56 OFF OFF OFF ON ON ON OFF
25 ON OFF OFF ON ON OFF OFF 57 ON OFF OFF ON ON ON OFF
26 OFF ON OFF ON ON OFF OFF 58 OFF ON OFF ON ON ON OFF
27 ON ON OFF ON ON OFF OFF 59 ON ON OFF ON ON ON OFF
28 OFF OFF ON ON ON OFF OFF 60 OFF OFF ON ON ON ON OFF
29 ON OFF ON ON ON OFF OFF 61 ON OFF ON ON ON ON OFF
30 OFF ON ON ON ON OFF OFF 62 OFF ON ON ON ON ON OFF
31 ON ON ON ON ON OFF OFF 63 ON ON ON ON ON ON OFF
32 OFF OFF OFF OFF OFF ON OFF 64 OFF OFF OFF OFF OFF OFF ON
-No.1 is changed to No.64 and the last No.64 is changed No.128 when No.7 DIP SW is on.
-No.1 is changed to No.129 when No.7 DIP SW is off and No.8 DIP SW is on.
-No.1 is changed to No.193 and user can set up to maximum 255 ADDRESS when No.7, 8 DIP SW are on.
13
4) HOW TO USE OSD MENU
4-1. How to control OSD menu
● OSD (ON SCREEN DISPLAY) CONTROL
It is the function to call up the Menu
＊User can not only set Preset, Group, Tour, Swing, Trace functions of the camera up by the menu, but also set
them up by shortening keys. (Refer to 3-3 content)
● Accessing OSD MENU
(1) The menu is displayed on the screen with the key tone when user presses No.1 and menu key.
● OSD Menu Control.
● OSD Menu Control Up, Down, Right and Left moving
of Cursor like under pictures
● Cancellation of OSD MENU
◄◄ CAMERA SETUP p1 ►►
1. ID Set : CAM-001
2. OSD Display. : ID + Status
3. H-V Reverse. : Normal
4. AGC Control : Max
5. Shutter speed. : AUTO
6. Sharpness level : 6
7. Brightness : 9
8. Flickerless : OFF
9. DNR Control : Medium
- NEXT MENU PAGE
14
4-2. Functional Descriptions of each Menu.
1. ID SET.
This function is to set
camera ID up to 16
letters on the monitor.
User can choose letters
that they want, if user
control a joystick up /
down / right / left, and
user can reselect the
previous letters, if user
presses Z/I, Z/O or turn the head of the joystick to right/left
2. OSD DISPLAY.
Set up whether user sets ID and STATUS to display on the
screen in normal operating.
● ID + Status: ‘ID’ and ‘Status’ displayed on the screen
● ID only: Only ‘ID’ displayed on the screen
● Status only: Only ‘Status’ displayed on the screen
● All off: Nothing displayed on the screen
3. H-V REVERSE
Set up H-V reverse mode.
● Normal
● H-REV : You can flip the picture horizontally on the screen.
● V-REV : You can flip the picture vertically on the screen.
● HV-REV : You can flip the picture horizontally and vertically on the
screen.
4. AGC CONTROL
AGC(Automatic Gain Control)- It adjusts the amount of video
amplification to maintain a full 1-volt peak-to-peak video signal output
automatically.
▶ Low, Medium, Max
◄◄ CAMERA SETUP p1 ►►
1. ID Set : CAM-001
2. OSD Display. : ID + Status
3. H-V Reverse. : Normal
4. AGC Control : Max
5. Shutter speed. : AUTO
6. Sharpness level : 6
7. Brightness : 9
8. Flickerless : OFF
9. DNR Control : Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1. ID Set : CAM-001
2. OSD Display. : ID + Status
3. H-V Reverse. : Normal
4. AGC Control : Max
5. Shutter speed. : AUTO
6. Sharpness level : 6
7. Brightness : 9
8. Flickerless : OFF
9. DNR Control : Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1. ID Set : CAM-001
2. OSD Display. : ID + Status
3. H-V Reverse. : Normal
4. AGC Control : Max
5. Shutter speed. : AUTO
6. Sharpness level : 6
7. Brightness : 9
8. Flickerless : OFF
9. DNR Control : Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1. ID Set : CAM-001
2. OSD Display. : ID + Status
3. H-V Reverse. : Normal
4. AGC Control : Max
5. Shutter speed. : AUTO
6. Sharpness level : 6
7. Brightness : 9
8. Flickerless : OFF
9. DNR Control : Medium
- NEXT MENU PAGE
15
5. SHUTTER SPEED
As a setting shutter speed mode, it can be distinguished a fast
moving subject easily by means of shutter speed up.
※ Attention-The illumination of the camera decreases if shutter
speed is up.
※The state of first default is ‘AUTO’.
※It can be worked in the state of Flickerless ‘off’
▶ Range : Auto, 1/125, 1/250, 1/500, --- 1/120000
6. SHARPNESS LEVEL
Compensation of the shape of a subject
▶ Range : 0 ~ 10, Default : 6
7. BRIGHTNESS
Control brightness of a screen.
The screen gets dark because an iris is closed as the numerical
value is low, whereas the screen gets bright because an iris
is opened as the numerical value is high.
▶ Range: 0~19, Default: 9
8. FLICKERLESS
Tremble on the screen is removed in the state of FLICKERLESS ‘ON’,
the shutter speed, at the same time, is fixed in 1/120sec in NTSC and
in 1/100sec in PAL.
▶ Off, Manual, On
◄◄ CAMERA SETUP p1 ►►
1. ID Set : CAM-001
2. OSD Display. : ID + Status
3. H-V Reverse. : Normal
4. AGC Control : Max
5. Shutter speed. : AUTO
6. Sharpness level : 6
7. Brightness : 9
8. Flickerless : OFF
9. DNR Control : Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1. ID Set : CAM-001
2. OSD Display. : ID + Status
3. H-V Reverse. : Normal
4. AGC Control : Max
5. Shutter speed. : AUTO
6. Sharpness level : 6
7. Brightness : 9
8. Flickerless : OFF
9. DNR Control : Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1. ID Set : CAM-001
2. OSD Display. : ID + Status
3. H-V Reverse. : Normal
4. AGC Control : Max
5. Shutter speed. : AUTO
6. Sharpness level : 6
7. Brightness : 9
8. Flickerless : OFF
9. DNR Control : Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p1 ►►
1. ID Set : CAM-001
2. OSD Display. : ID + Status
3. H-V Reverse. : Normal
4. AGC Control : Max
5. Shutter speed. : AUTO
6. Sharpness level : 6
7. Brightness : 9
8. Flickerless : OFF
9. DNR Control : Medium
- NEXT MENU PAGE
16
9. DNR Control
It can remarkably reduce noise of minimum illumination by super
noise removable technique and also file size becomes smaller while
DVR is being recorded by the effective reduction of noise.
▶ Off, Low, Medium, Max
10. BACK LIGHT
This camera is designed so that it delivers a distinctive subject and
background at the same time, even when the subject is in backlight,
unlike conventional cameras, by adopting a proprietary DSP chip.
.Please select a suitable mode below them (The Set Back Light Mode
will be automatically changed by the selection)
▶ Off, WDR MODE, HLC MODE, BLC MODE
WDR : When there are both bright and dark areas at the same time,
this mode makes both areas distinctive.
BLC : Enables a user to directly select a desired area from a picture, and to view the area more clearly..
HLC(High Light Compensation) : If there is a high light installed in dark environment such as an apartment
parking garage or gas station entrance, removing the high light makes it possible to view car license plates
efficiently
OFF : Deactivates the BACKLIGHT function.
11. SET BACK LIGHT MODE
▶ WDR MODE
- Limit: Adjust the WDR Sensitivity by selecting Low or Max
- Level: Adjust the WDR Brightness by controlling 0~15.
▶ HLC(High Light Compensation)MODE
- Limit: Adjust the HLC Sensitivity by selecting Low, Medium or Max
- Level: Adjust the WDR Brightness by controlling 0~15.
- This Function only operate in nighttime.
▶ BLC MODE : Select BLC mode or BLC Set area mode by using
the joystick.
- BLC Level: Adjust the BLC Sensitivity by selecting Low, Medium or Max
- BLC Set AREA (Press F/F): Set BLC area location and size
- Select F/F button, and set the BLC area by using the joystick, and set are size by using Z/I, Z/O buttons.
(The monitor shows as Exit BLC set(Press F/N)
After complete all setup, press F/N button, and then move to RETURN MENU PAGE. It is automatically saved.
◄◄ CAMERA SETUP p1 ►►
1. ID Set : CAM-001
2. OSD Display. : ID + Status
3. H-V Reverse. : Normal
4. AGC Control : Max
5. Shutter speed. : AUTO
6. Sharpness level : 6
7. Brightness : 9
8. Flickerless : OFF
9. DNR Control : Medium
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10. Back Light : WDR Mode
11. Set Back Light Mode
12. White Balance : Auto
13. Focus Mode :Oneshot
14. Zoom Max Limit : Off
15. DSS Control : 10 Field
16. Day&Night : Auto+Hi
17. Stabilize On/Off : Off
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10. Back Light : WDR Mode
11. Set Back Light Mode
12. White Balance : Auto
13. Focus Mode :Oneshot
14. Zoom Max Limit : Off
15. DSS Control : 10 Field
16. Day&Night : Auto+Hi
17. Stabilize On/Off : Off
- PREV MENU PAGE
- NEXT MENU PAGE
17
12. WHITE BALANCE
It prevents from that white color is changed as illumination, user can
set it up in 2 ways.
▶ Auto, Indoor, Outdoor
13. FOCUS MODE
Change Focus Mode to hand-worked or auto.
▶ OneShot : Auto Focusing mode works during non-working
after zoom is worked.
▶ Auto: It adjusts the focus automatically as it monitors the
screen.
▶ Manual: User can control the focus by hand-worked.
14. ZOOM MAX Limit
It is used when user corrects and limits the extensional range
of the focus as a function to set the maximum value of zoom.
▶ Off,
▶ 27x zoom : 54X ~ 432X
33x zoom : 66X ~ 528X
37x zoom : 74X ~ 592X
15. DSS CONTROL
An object becomes clear as the field value gets higher in
illumination, whereas a moving object becomes dim.
▶ Range : Off, 2 ~ 512 fields
◄◄ CAMERA SETUP p2 ►►
10. Back Light : WDR Mode
11. Set Back Light Mode
12. White Balance : Auto
13. Focus Mode :Oneshot
14. Zoom Max Limit : Off
15. DSS Control : 10 Field
16. Day&Night : Auto+Hi
17. Stabilize On/Off : Off
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10. Back Light : WDR Mode
11. Set Back Light Mode
12. White Balance : Auto
13. Focus Mode :Oneshot
14. Zoom Max Limit : Off
15. DSS Control : 10 Field
16. Day&Night : Auto+Hi
17. Stabilize On/Off : Off
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10. Back Light : WDR Mode
11. Set Back Light Mode
12. White Balance : Auto
13. Focus Mode :Oneshot
14. Zoom Max Limit : Off
15. DSS Control : 10 Field
16. Day&Night : Auto+Hi
17. Stabilize On/Off : Off
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10. Back Light : WDR Mode
11. Set Back Light Mode
12. White Balance : Auto
13. Focus Mode :Oneshot
14. Zoom Max Limit : Off
15. DSS Control : 10 Field
16. Day&Night : Auto+Hi
17. Stabilize On/Off : Off
- PREV MENU PAGE
- NEXT MENU PAGE
18
16. DAY& NIGHT
The function is used to distinguish an object clearly in the dark
condition.
▶ Auto-Low : This mode is worked automatically according to
sensitivity, if the sensitivity is low
▶ Auto-Hi : This mode is worked automatically according to
sensitivity, if the sensitivity is high.
▶ On : Change into DAY & NIGHTY mode by hand-worked
▶ Off : Set DAY & NIGHTY mode ‘off’
17. STABILIZE On/Off
There is some tremble as zoom magnification is high, the function
can compensate the tremble.
▶ On / Off
18. SELECT ALARM
Tremble on the screen is removed in the state of FLICKERLESS
‘ON’, the shutter speed, at the same time, is fixed in 1/120sec in
NTSC and in 1/100sec in PAL.
Alarm CH On/Off Page
19. Motion Detection
Set Motion ‘On’ after move the camera where user wants.
It displays the message ‘Motion Detected’ on the screen
when the moving of an object is sensed on the same screen.
◄◄ CAMERA SETUP p2 ►►
10. Back Light : WDR Mode
11. Set Back Light Mode
12. White Balance : Auto
13. Focus Mode :Oneshot
14. Zoom Max Limit : Off
15. DSS Control : 10 Field
16. Day&Night : Auto+Hi
17. Stabilize On/Off : Off
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p2 ►►
10. Back Light : WDR Mode
11. Set Back Light Mode
12. White Balance : Auto
13. Focus Mode :Oneshot
14. Zoom Max Limit : Off
15. DSS Control : 10 Field
16. Day&Night : Auto+Hi
17. Stabilize On/Off : Off
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p3 ►►
18. Select Alarm : Sensor
19. Motion Detection : Off
20. Preset Set & Run Page
21.Trace Set Page
22. Alarm CH On/Off Page
23. Alarm Preset Set Page
24. Privacy Zone Set Page
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p3 ►►
18. Select Alarm : Sensor
19. Motion Detection : Off
20. Preset Set & Run Page
21.Trace Set Page
22. Alarm CH On/Off Page
23. Alarm Preset Set Page
24. Privacy Zone Set Page
- PREV MENU PAGE
- NEXT MENU PAGE
19
20. PRESET SET & RUN PAGE
It is a function to set and operate Preset, Group, Tour.
User can see the screen when moves the joystick to Right/Left after
fixing the cursor on the menu.
<<PRESET SETUP PAGE>>
① Preset set CH :
User can set Preset No. and title on this menu.
- Preset No. set : Set it by moving the joystick to Right/Left
- Preset title set : User can see the menu “SET ID” when
press F/F key after setting Preset No
.
•[SAVE]: Previous screen. [DELETE]: Remove. [ESC]: Cancel
◄◄ CAMERA SETUP p3 ►►
18. Select Alarm : Sensor
19. Motion Detection : Off
20. Preset Set & Run Page
21.Trace Set Page
22. Alarm CH On/Off Page
23. Alarm Preset Set Page
24. Privacy Zone Set Page
- PREV MENU PAGE
- NEXT MENU PAGE
② Preset PTZ set : Set the position of Preset
Select the main menu with the joystick, then
press F/F key for next page.
Select [SAVE] with F/N key after setting the
Preset point by using the joystick and. In/Out
function, then the data is saved if user
presses F/F key, then it is moved to the
previous screen automatically from the menu
※ Repeat the same way after changing the
number of Preset, if user set another Preset
20
③ Preset Swing SET : Set Preset Swing
Move next SWING page for the setting, if user
presses F/F key in the state of selection of the menu
※The preset must be set before the setting as Swing
Is a function to repeat an auto observation of 2 Preset points user fixes in Preset set
④ GROUP SET: User can set maximum 12 groups.
Select a channel then move to next page after
pressing F/F key
※The Preset point in the Group that 12 Preset
points are set is observed repeatedly and order
with regular speed and time.
⑤ Tour SET Group: User can set continual Group motion that can be put 12 Groups in 1 Tour Move to the setting
21
page if user presses F/F key on this menu
■ The Group user wants to set must be set firstly
※Setting is only possible when Preset is set first in the state of setting of Swing, Group, Tour, otherwise, it displays
the message “Sorry Undefined”.
⑥ Run Function: Operate one of SWING/ ＊Set / Stop order with a control keyboard without menu GROUP /
TOUR / TRACE. (It is operated on the screen. automatically after end of OSD menu)
■ User can look at how to set TRACE at TRACE SET PAGE”
⑦ RETURN MENU PAGE: Move to a higher menu page when control the joystick Right/Left in the
Selection of this menu.
21. TRACE SET PAGE
Set TRACE.
User can regenerate and save a change of the unrestricted location of
ZOOM In/Out and a position of the camera by hand-worked control
with a joystick.
User can see the screen when moves the joystick to Right/Left after
fixing the cursor on the menu
■ How to set TRACE
Move to [SET] after pressing
Check – Control scenes that user wants by hand-worked with a
joystick after the message.
“Set Trace: OO%” on the middle of the screen. If user finishes
this part, Move to [SAVE] with
It goes a higher menu after being saved data if user presses with a
display of the message “Save TRACE”
◄◄ CAMERA SETUP p3►►
18. Select Alarm : Sensor
19. Motion Detection : Off
20. Preset Set & Run Page
21.Trace Set Page
22. Alarm CH On/Off Page
23. Alarm Preset Set Page
24. Privacy Zone Set Page
- PREV MENU PAGE
- NEXT MENU PAGE
22
22. ALRAM CHANNEL ON/OFF
- CH On/Off : Alarm Input – Each channel can be ON/OFF
- Alarm Relay : It can be set On or not when ALARM OUTOUT
PORT operate wrong.
- Active Alarm : It selects ACTIVE OPEN or ACTIVE CLOSE by
tangency when something is wrong. It is ACTIVE when ALARM INPUT
is OPEN in ACTIVE OPEN, it is ACTIVE when ALARM INPUT is
CLOSE in ACTIVE CLOSE
- Resume Time Set :
It can select the delay time that the camera move to the place
alarming to observe where wrong signal is sensed.
User can set it for 1sec to 180sec and operate GROUP, TOUR,
SWING again in a preset time. SWING, GROUP, TOUR are operated
in a preset time when user stops the operating joystick in the case of not connecting with the ALARM.
Press SWING, GROUP, TOUR keys without stopping of the joystick to stop the operating completely
(*Stopping the operating with the joystick affects the SET function.)
23. ALARM PRESET SET PAGE
■ The camera can move to a preset point automatically when
something is wrong in each ALRAM CHANNEL.
■ Set a preset point firstly to move if anything wrong, then use
that sets the preset number into each ALARM CHANNEL.
■ PRESET is out of connecting in ALARM CHANNEL No.“0”
■ User can select PRESET number 1 to 250 and set it.
■ Home Position Preset
The camera automatically moves to where master user set
when another user controls the camera to observe other area.
(You can set 1~250 points)
■ Home Position Time
It sets the dwell time in Home Position Preset.
It automatically moves to where observes ordinarily in the
regular time that Master user set in observation of other area
,if set Home Position Preset
(You can set 1~180sec. Set control Home Position Preset
and Home Position Time together for using this function.)
※You can set ALARM setting MENU not only in CAMERA SET MENU MODE, but also a KEYBOARD in direct
◄◄ CAMERA SETUP p3 ►►
18. Select Alarm : Sensor
19. Motion Detection : Off
20. Preset Set & Run Page
21.Trace Set Page
22. Alarm CH On/Off Page
23. Alarm Preset Set Page
24. Privacy Zone Set Page
- PREV MENU PAGE
- NEXT MENU PAGE
◄◄ CAMERA SETUP p3 ►►
18. Select Alarm : Sensor
19. Motion Detection : Off
20. Preset Set & Run Page
21.Trace Set Page
22. Alarm CH On/Off Page
23. Alarm Preset Set Page
24. Privacy Zone Set Page
- PREV MENU PAGE
- NEXT MENU PAGE
23
24. PRIVARCY ZONE SET
Max
16 privacy zones can be configured for the protection of privacy.
■ How to set privacy zone
In <<PRIVACY ZONE SET>> menu, select the channel that
you want by a joystick, then move to the next page if you
press the
[F/F] key
①
Select a Channel
④ Fix the black square on the middle of area that you want to
hide by a joystick, then go back to the previous page by [F/F] key
after controlling the size of the square by [Z/I], [Z/O] key and saving it.
Set the position BOX Extension / Reduction Check
⑤ The Channel is changed BLANK to ‘OFF’.
The screen displays the black square, if you change the CH ON’ as the left picture.
⑥ Out of OSD MENU
◄◄ CAMERA SETUP p3►►
18. Select Alarm : Sensor
19. Motion Detection : Off
20. Preset Set & Run Page
21.Trace Set Page
22. Alarm CH On/Off Page
23. Alarm Preset Set Page
24. Privacy Zone Set Page
- PREV MENU PAGE
- NEXT MENU PAGE
24
25. AUTO TILT MOVE
The PAN is turned in a 180° degree arc automatically when the angle
of the camera moves down to the maximum degree, therefore, it is
possible to track objects continuously
26. SMART PANTILT
It is a function that P/T speed is getting slower as Zoom in.
It is hard to observe objects with the high PANTILT speed in
operating of Zoon In
This function makes the speed less automatically for the effective
observation
27. MANUAL P/T SPEED
User can control the maximum speed in controlling of up and down.
It can be set Low, Medium, Max and one turn (360°/sec) is possible
in Max.
28. AUTO REFRESH TIME
Auto refresh can be set from 1 to 7days (each) for good focus
performance
◄◄ CAMERA SETUP p4►►
25. Auto Tilt Mode : Off
26. Smart Pan/tilt : ON
27. Manual P/T Speed : Medium
28. Auto Refresh Time :1day
29. Shortcut Key : On
30. Use Password :Off
31. Language :English
32. Factory Reset Warning
- PREV MENU PAGE
◄◄ CAMERA SETUP p4►►
25. Auto Tilt Mode : Off
26. Smart Pan/tilt : ON
27. Manual P/T Speed : Medium
28. Auto Refresh Time :1day
29. Shortcut Key : On
30. Use Password :Off
31. Language :English
32. Factory Reset Warning
- PREV MENU PAGE
◄◄ CAMERA SETUP p4►►
25. Auto Tilt Mode : Off
26. Smart Pan/tilt : ON
27. Manual P/T Speed : Medium
28. Auto Refresh Time :1day
29. Shortcut Key : On
30. Use Password :Off
31. Language :English
32. Factory Reset Warning
- PREV MENU PAGE
◄◄ CAMERA SETUP p4►►
25. Auto Tilt Mode : Off
26. Smart Pan/tilt : ON
27. Manual P/T Speed : Medium
28. Auto Refresh Time :1day
29. Shortcut Key : On
30. Use Password :Off
31. Language :English
32. Factory Reset Warning
- PREV MENU PAGE
25
29. SHORTCUT KEY
The Shortcut Key can make some of the functions to perform faster
and easily.
★ How to use shortcut key ( All protocols is operated it at the same way )
Function Operation Function Operation
Group 1 51 + Preset Run Trace 66 + Preset
Group 2 52 + Preset Run Spiral 67 + Preset
Group 12 62 + Preset B/W Mode 68 + Preset
Run Tour 63 + Preset Color Mode 69 + Preset
Run Pan Swing 64 + Preset OSD Menu ON/OFF 95 + Preset
Run Tilt Swing 65 + Preset
30. USE PASSWORD
- input the password
- available set On/Off mode; off mode is factory set
- press the F/F button as On mode
- A window will be pop-up for input Old and New
passwords. Old password is set as ‘0000’. To input a
new password, use the joystick as up, down, right, and
left
- Press F/F button to save the new password. The new
password will be needed when access the OSD mode
31. LANGUAGE
English, Portuguese, Polish
◄◄ CAMERA SETUP p4►►
25. Auto Tilt Mode : Off
26. Smart Pan/tilt : ON
27. Manual P/T Speed : Medium
28. Auto Refresh Time :1day
29. Shortcut Key : On
30. Use Password :Off
31. Language :English
32. Factory Reset Warning
- PREV MENU PAGE
◄◄ CAMERA SETUP p4►►
25. Auto Tilt Mode : Off
26. Smart Pan/tilt : ON
27. Manual P/T Speed : Medium
28. Auto Refresh Time :1day
29. Shortcut Key : On
30. Use Password :Off
31. Language :English
32. Factory Reset Warning
- PREV MENU PAGE
◄◄ CAMERA SETUP p4►►
25. Auto Tilt Mode : Off
26. Smart Pan/tilt : ON
27. Manual P/T Speed : Medium
28. Auto Refresh Time :1day
29. Shortcut Key : On
30. Use Password :Off
31. Language :English
32. Factory Reset Warning
- PREV MENU PAGE
26
32. FACTORY RESET WARNING
Please be careful of that all setting data of OSD MENU are reset
into the first default when operates FACTORY RESET WARNING.
The setting data of Preset, Swing, Group, Tour, Trace, also is
deleted all
◄◄ CAMERA SETUP p4►►
25. Auto Tilt Mode : Off
26. Smart Pan/tilt : ON
27. Manual P/T Speed : Medium
28. Auto Refresh Time :1day
29. Shortcut Key : On
30. Use Password :Off
31. Language :English
32. Factory Reset Warning
- PREV MENU PAGE
27
4-3. Functional Setting, Operating/Deletion by the Keyboard
1. Preset setting
You can set Preset point up to 250.
Preset Input.①
Preset setting can be set 1 to 250 sequentially after
moves the camera to where you want
② Preset Move
The camera moves to the preset point, if you press
Preset No. that you want and P-SET Key
③ Delete a separate Preset
Go on in order as below when the sound is heard Ex) Delete 5
th
Preset
in 3 seconds after pressing CLR Key
(Waiting for 3seconds)
④ Delete all Preset
Go on in order as the right picture when the sound is heard
in 3 seconds after pressing CLR KEY (Waiting for 3seconds)
2. Swing setting
① Swing Input
Tilt setting
Pan setting
Starting Preset
Ending Preset No
Set the delay time (1~127sec)
Set the move speed (1~64 steps)
28
② Operation of Swing ③ End of Swing
(Run Pan) (Run Tilt)
3. Group setting
① Start Group setting mode
- Set Preset No. again if you want to input it continuously.
- Set a GROUP again from the first after ending with SET Key , if you want to finish Preset input in one
Group to input next Group.
② Start a Group ③ Stop the Group
.
You can stop it when pressing Group key or using a joystick
4. Tour setting
① Tour set mode
Start the Tour set mode Select a Group in 1 ~ 12
Start the Group
setting mode
Select in Preset No.1~250
and input them.
Select the Group in 1~12
Move Speed:
The Speed from A to B
64=High, 1=Low
Dwell Time:
The dwell time at the point of
A or B before the move. (sec)
29
■ Repeat input in continual input
EX). Register Group No. 1,3,6 as Tour
② Start / End Tour ③ Delete Tour
Start Tour Finish Tour
5. Spiral Function
It is a function to observe objects in the spiral direction.
① Spiral observation ‘ON’ ② End
6. PTZ Trace
It memorizes P/T/Z motions for 200sec, then operates them at the same Trace.
① Start / End Trace
② Set Trace ③ Delete Trace
Register
Tour No.1
Register
Tour No.3
Finish
Tour mode
Start
Tour mode
Register
Tour No.2
30
4-4. OSD MESSAGE DISCRIPTION
31
32
4. TROUBLE SHOOTING
33
5. DIMENSION
Wall mount bracket
Ceiling mount bracket
34
In-ceiling mount bracket
35
Unscrew the 5bolts from the Bubble cover①
and open it, then separate the Camera body
from the Cover housing.
(The bolts from the Bubble cover are not
separated completely.)
②Connect each cables, then screw 4 bolts.
Block up beside the hole with 34mm BLANK RUBBER
③In set of it on the concrete, connect the cables as
above the picture and join TAB/P1/11” flexible
connector(28Ø)
④Connect the Cover housing with Wall bracket as
Above the picture.
6. ASSEMBLY
DSC-30EWP Wall mount bracket
36
Connect the Housin⑥ g with the camera body.
Please check the triangular mark on the side
of the body and inside.
⑦Connect the Bubble again.
⑤Connect the Data, Video, Power cables.
(Refer to page 7)
37
Unscrew the 5bolts from the Bubble cover①
and open it, then separate the Camera body
from the Cover housing.
(The bolts from the Bubble cover are not
separated completely.)
②Fix the Pole box from the ceiling.
⑤Turn the Cover housing tight.
DSC-20ECP Wall mount bracket
38
Connect the Data, Video, Power⑥
cables. (Reference to Installation
and Connection.)
⑦Connect the Housing with the camera body.
Please check the triangular mark on the side
of the body and inside.
⑧Connect the Bubble again.
Ceiling bracket is used as In/Outdoor type
and you can remove or extend the Ceiling
pole to fix the length. It is manufactured
as a standard size by our-self.
39
40
Ceiling Adhesion bracket
41
Set sub keyboard
42
Set one main keyboard
43
※ The content of the manual is changeable to improve the quality.
MODEL
27X Zoom □ 33X Zoom □ 37X Zoom □
Image sensor 1/4” Sony Super HAD CCD
Effective pixels NTSC 768(H) X 494(V), PAL 752(H) X 582(V),
Horizontal resolution Color : 600 TVL, B/W 700 TVL
Lens (Digital Zoom) 27x Optical zoom(16x),
33x Optical zoom(16x),
f =3.5 –115.5mm
37x Optical zoom(16x),
f =3.5 –129.5mm
Angle of view
H : 55.5° ~2.24° ,
V : 42.5°~1.79°
H : 55.5° ~1.77° , V :
42.5°~1.33°
H : 55.5° ~1.59° , V :
42.5°~1.19°
Minimum illumination 0.7 Lux , 0.1Lux(D&N), Min 0.00004Lux(DSS) / F1.6 (50IRE)
Luminance S/N ratio More than 52dB
Video output 1 Vp-p Composite video output 75Ω
Focus mode Auto / Manual / Oneshot
DNR Off / Low / Middle / High
Back Light Control BLC / HLC / WDR
Shutter speed Auto / 1/120 ~ 1/120,000 sec
Sharpness control Level (0 – 10)
Stabilizer On/Off
Alarm in/out 8 Inputs / 2 Relay Output
Pan/Tilt angle 360° Endless / 92°
Preset point 250 Presets
Preset Speed Max 360°/sec (64 Levels)
Privacy zones masking 16 Zones
Operating temperature /
Operating humidity
- 40°C ~ 50°C (-40°F ~ 122°F) (Outdoor Model) / Less than 90%RH
- 10°C ~ 50°C (-14°F ~ 122°F) (Indoor Model) / Less than 90%RH
Communiction system RS-485 / 422
Operating Fan/Heater Over than 45°C / Less than 5°C (Only Outdoor Model)
Dimensions
155.6mm(Diameter) x 223.6(Height) mm (Indoor Model)
215.6mm(Diameter) x 279.6(Height) mm (Outdoor Model)
Weight About 5.2Kg (Outdoor Model), About 3.1Kg (Indoor Model)
Construction
Aluminum body , Clear vandal bubble (PC) (Outdoor Model)
ABS body , Clear vandal bubble (PC) (Indoor Model)
Power consumption 21W (Max) Indoor Model / 18W (Max) Outdoor Model
Power supply AC24V, 60/50 Hz
7. SPECIFICATION
44
45
DISTRIBUTED BY
Loading...