2Megapixel
TVI & AHD
Hybrid
Mini Speed Dome Camera
User manual
Version. 100927
AHD and TVI video output selection
Indoor
Outdoor
Set AHD or TVI video output using dip
switches on the camera body at bottom
cover.
Loosen the four bolts of the Bubble Cover,
Remove the camera housing, and set AHD or TVI
video output using dip switches on the camera
body at connect cover
NOTE) If only CVBS output ie when using only analog CVBS output without using the TVI / AHD
output must TVI / AHD mode should be used, and to TVI mode. AHD mode when the camera is
malfunctioning, and reboot. Be careful.
AHD
TVI
You can set AHD or TVI video output of the right side DIP switch to the third position.
２
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
Content
1. Caution.................................................................................................................................................................................................. 4
2. Product Introduction ........................................................................................................................................................................ 6
2.1. Description and features ............................................................................................................................................ 6
2.2. Product package ........................................................................................................................................................... 7
2.3. Name and function of each part ............................................................................................................................. 8
2.4. Installation ......................................................................................................................................................................10
2.4.1. Installing wall mount bracket-(Outdoor) ...................................................................................................10
2.4.2. Basic Installation for Indoor ..........................................................................................................................11
2.4.3. Wall Bracket Installation for Indoor Type ................................................................................................12
2.4.4. Installing Ceiling Mount Bracket -Outdoor ..............................................................................................13
2.4.5. Using Speed Dome Junction Box ..............................................................................................................14
2.4.6. Installing Corner Mount ..................................................................................................................................16
2.4.7. Installing Pole Mount .......................................................................................................................................16
3. DIP switch setting ...........................................................................................................................................................................17
3.1. DIP Switch setting ......................................................................................................................................................17
3.2. Protocol setting ............................................................................................................................................................18
3.3. Address DIP Switch Setting ...................................................................................................................................19
3.4. OSD Menu setting ......................................................................................................................................................20
3.4.1. OSD Menu control ............................................................................................................................................20
3.4.2. Menu function .....................................................................................................................................................21
3.4.3. Set-up menu, Execute and delete by keyboard ...................................................................................42
3.4.4. OSD Message Description ...........................................................................................................................45
4. TROUBLE SHOOTING ................................................................................................................................................................47
5. Dimension ..........................................................................................................................................................................................48
5.1. Outdoor type .................................................................................................................................................................48
5.2. Indoor type .....................................................................................................................................................................49
6. Configuration diagram ..................................................................................................................................................................50
7. Specification .....................................................................................................................................................................................51
3
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
Note the following matters before the installation of the product.
Avoid the following places for the installation.
A high/low temperature
→ Using indoor-cameras in the places of +50°C~ -10°C can cause troubles and lower its
capacity.
Snow, rain and wet
→ Humidity or water and any liquid inside-camera can cause troubles.
Oil, gas
→ Oil and gas can damage the camera as they go through the cameras.
Vibration, shock
→ They bring on problems or errors of the camera.
Direct light, exposure to the air
→ In the case of that sets indoor- cameras outside where the weather is changeable, it can
cause problems.
Closing to High frequency and electric power lines
→ Setting the camera up around electromagnetic units or power supplier can cause problems.
Do not disassemble the unit and put alien substances in the unit.
Disassembling the unit or putting alien substances such as a metal can
make the camera defective.
Make sure of power switch-off before the installation.
→ Ensure power switch-off and check the voltage the camera before the installation.
Do not give the unit a shock and an operation.
→ Giving a strong shock or an excessive power on the button, terminal can cause problem.
1. Caution
Thank you for purchasing our product. Please operate the product after being fully aware of the
manual. Pease contact us if you have any query.
Precaution
Caution in Use
4
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
This product has been designed and manufactured in accordance with the harmonized European standards,
following the provisions of the below stated directives.
Electromagnetic Compatibility Directive 89/336/EEC(EN61000-3-2:1995, EN61000-3-3:1995, EN50081-
1:1992, EN50082-1:1997)
This devise complies with part 15 of the fcc rules operation is subject to the following two conditions: (1) This
device may not cause harmful interference and (2) This device must accept any interference received
including interference that may cause undesired operation
Caution :
① Must use AC24V power source, current intensity must be less than 2A and must use
a double winding transformer.
② Never extend the power line from adaptor to camera.
③ Please use more thick cable than 18AWG(1.0mm), if you want to extend the power
line.
④ You must use one adaptor per one camera that is being provided.
⑤ Use extra power supplier, If you want to supply many piece of cameras.
5
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
2. Product Introduction
2.1. Description and features
This camera, 2 Megapixel Full HD TVI/AHD Hybrid Mini speed dome camera, has been designed
elegantly for buildings, department stores that need to be in harmony with the interior as a high
speed dome camera, including various observation functions.
- Feature -
Support full 2.2 Megapixel Full HD-SDI (1080p)
Optical x10 zoom rates, Digital x32 zoom rates
Enhance Electronic sensitivity lowest illumination 0.003Lux (DSS Control)
Change to B/W model (0.1Lux) at night by ICR DAY & Night
Digital Noise Reduction (DNR), True WDR
DEFOG Function
Motion detection, Privacy zones.
Various surveillance functions
Preset(250), Group(12), Tour, Trace, Spiral
Remove moisture inside of camera by using fan & heater(In case of indoor type fan only
operate)
Automatic movement detecting area as Alarm receiver unit or Sensor
RS422/485 remote control
Built-in Auto Tilt (Automatic 180° tilt rotation)
6
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
Item
Q`ty
Outdoor type
Indoor type
MEGA Speed Dome
Camera
1 pcs
Wall Mount Bracket
1 pcs n/a
Power Supply
(Power Cable & Linear
AC24V/2.5A adapter)
1 pcs n/a
Bracket Blank Rubber
2 pcs n/a
ceiling guide
1 pcs
n/a
screw
2/4 pcs
(spare)
screw anchor
4 pcs
n/a
User's Manual
1 copy
2.2. Product package
The following items are included in the product package.
7
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
No
Name
Function
①
Dome Clear Bubble
Protect Lens and PTZ dome drive
②
PTZ Camera
PTZ dome drive (Pan/Tilt/Zoom)
③
Camera Housing
Indoor/Outdoor PTZ housing.
④
Cable
POWER (AC24V)
TVI 또는 AHD 영상 출력 단자
CVBS Out
RS-485 terminal
Alarm in
Brown: CH 1
Yellow: CH 2
Blue: CH 3
Purple: CH 4
Gray: GND
Alarm Out
White/Blue: N/O
Pink: N/C
Light Green: COM
⑤
Wall Mount Bracket
Attached wall bracket on the wall
2.3. Name and function of each part
- Exterior -
8
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
No.
Name
Function
①
Power Port
AC 24V / 2A Power input
②
RS-485 Communication Port
RS-485 PTZ control communication port
③
Video Out Port
AHD or TVI video output port(1080P 25/30 FPS)
④
ALARM In / Output port
ALARM In / Output port
⑤
DIP Switch (1~7, 8)
No.1~7: Address Setting switch / No.8: NTSC or PAL
selectable
DIP Switch (1~4)
Set-up Setting switch
⑥
Power LED
Turn on the light when its power on
① ② ⑤
⑥ ④ ③
- Interior -
Connect Cover
9
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
① Loosen the 4 bolts of
Bubble Cover and
disconnect the camera
housing.
② -1. Put cables (Power, Video, data) in the
bracket and fasten bracket on the wall by 4
bolts then close both holes provided 34mm
Blank rubber
② -2. When the camera is installed retaining wall
or Concrete building, put the cables in the
bracket as picture and close hole by TAB/P1/11"
flexible connector(28mm)
③ Connect the power, data, & video cables to the
connection part of Connect Cover and then set
the DIP SWITCH.
④ After completing
the connection,
please recombine
the camera body &
the housing with the
bolts and then
connect to the
bracket.
⑤ The installation of
wall mount bracket
is completed.
2.4. Installation
2.4.1. Installing wall mount bracket-(Outdoor)
10
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
① Make 4 holes after
attaching ceiling guide
where the camera is set.
② Take out the cables from the
ceiling.
③ Take apart 4 bands of camera body cover.
④ Set up DIP switch.
⑤ Connect with cables.
⑥ Tighten 4 screws.
⑦ Attach the camera body cover.
⑧ Completion
2.4.2. Basic Installation for Indoor
11
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
① Connect MOUNT with Wall
bracket.
② Fix 4 screws.
③ Connect Camera body cover.
Completion
2.4.3. Wall Bracket Installation for Indoor Type
It can be connected with bracket by using mount.
(The mount and bracket are optional item for indoor type. )
12
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
① Loosen the 4 bolts of
Bubble Cover and
disconnect the camera
housing.
② Attach Pole box on the ceiling.
③
④ Connect the power, data, & video cables to the
connection part of Connect Cover and then set
the DIP SWITCH.
⑤ When completing the
connection and the DIP switch
installation, please recombine
the camera body and the
housing.
Tighten Ceiling pole to
pole box
Tighten Joint couple
Tighten Cover housing
2.4.4. Installing Ceiling Mount Bracket -Outdoor
13
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
2.4.5. Using Speed Dome Junction Box
- Speed dome junction box installation -
Fasten screw up 4 screws of the junction box in order of Camera housing → Wall mount bracket →
Water-proof cover → Speed dome junction box → Wall
Junction box connection Camera connection
For connecting cables in the junction box, Please refer to wall mount bracket installation part The PTZ
junction box inside part is as below.
14
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
AC 24V Power Supply
AC 24V Input Port
AC 24V Output Port
Power LED
AC OUT
AC IN
Input port
Output port
LAN (Input)
LAN (output)
※ Please refer to the speed dome junction box user manual.
15
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
2.4.6. Installing Corner Mount
When installing the wall mount bracket to
the corner of wall, install it with the corner
mount.
2.4.7. Installing Pole Mount
When installing the wall mount bracket on the cylinder, combine it
with the pole mount and install it.
16
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
<S1>
SET No#1~7 DIP SWITCHES FOR CAMERA
ADDRESS.
SET INIT DIP SWITCHES FOR CAMERA
PROTOCOL & BAUD RATES. (This part is each
address of camera)
SET 8th DIP SIWTCH FOR NTSC/ PAL SIGNAL.
<POWER LED>
It shows the status of Power On/Off.
Green LED is On while power is alive.
In the status of operation, red LED is
off.
<S2>
- Termination Resistor (DIP S2/SW1)
→ Turn the last camera on the data line as a switch to
turn on/off the terminal resistor on.
Turn the DIP SW of some of the farthest cameras on
in the case of the data lines distributed to several
directions.
(* The default is off.)
- Address / Initial Select (DIP S2/SW2)
→ Set ADDRESS DIP SW in the status of ADDRESS
(* Reference to next page *)
(.*** The first default is ADDRESS.**)
Set the communication speed (baud rates) and Protocol
(Demand for the technical inquiry) up in the state of the
INITAIL.
-Select TVI or AHD output (DIP S2/SW 3)
→ TVI : TVI output, AHD : AHD output
- Power On/Off (DIP S2/SW 4)
→ Set DIP SW only in the status of Power off. Then turn
on the power after setting DIP SW.
3. DIP switch setting
3.1. DIP Switch setting
17
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
PROTOCOL
S1
S2
SW1
SW2
SW3
SW6
SW7
SW 'INIT←→ADDR'
D-MAX (9600 bps)
OFF
OFF
OFF
OFF
OFF
INIT
P-P (9600 bps)
ON
OFF
OFF
OFF
OFF
INIT
P-P (4800 bps)
ON
OFF
OFF
OFF
ON
INIT
P-P (2400 bps)
ON
OFF
OFF
ON
OFF
INIT
P-D (9600 bps)
OFF
ON
OFF
OFF
OFF
INIT
P-D (4800 bps)
OFF
ON
OFF
OFF
ON
INIT
P-D (2400 bps)
OFF
ON
OFF
ON
OFF
INIT
S-T (9600 bps)
OFF
OFF
ON
OFF
OFF
INIT
3.2. Protocol setting
Set up the switch. (8th DIP SIWTCH can converted NTSC/ PAL SIGNAL.)
The switch for select protocol The switch for select baud rates
Change S2 to INIT if user wants to change protocol
① Please the power off
② Switch protocol that user wants to change on in the above the table
③ The power on, then the set protocol and baud rates are displayed.
④ The power off, if every setting is right. Then the change of protocol is finished.
⑤ Change No. 2 of S2 to ADDR before the power on, then the power on after setting the address of the
camera.
⑥ Try it again with the information as above the table, if something is wrong
18
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
RX
NO
DIP SWITCH (HEX)
RX
NO
DIP SWITCH (HEX)
1 2 3 4 5 6 7 1 2 3 4 5 6
7
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
33
ON
OFF
OFF
OFF
OFF
ON
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
34
OFF
ON
OFF
OFF
OFF
ON
OFF
3
ON
ON
OFF
OFF
OFF
OFF
OFF
35
ON
ON
OFF
OFF
OFF
ON
OFF
4
OFF
OFF
ON
OFF
OFF
OFF
OFF
36
OFF
OFF
ON
OFF
OFF
ON
OFF 5 ON
OFF
ON
OFF
OFF
OFF
OFF
37
ON
OFF
ON
OFF
OFF
ON
OFF
6
OFF
ON
ON
OFF
OFF
OFF
OFF
38
OFF
ON
ON
OFF
OFF
ON
OFF
7
ON
ON
ON
OFF
OFF
OFF
OFF
39
ON
ON
ON
OFF
OFF
ON
OFF
8
OFF
OFF
OFF
ON
OFF
OFF
OFF
40
OFF
OFF
OFF
ON
OFF
ON
OFF
9
ON
OFF
OFF
ON
OFF
OFF
OFF
41
ON
OFF
OFF
ON
OFF
ON
OFF
10
OFF
ON
OFF
ON
OFF
OFF
OFF
42
OFF
ON
OFF
ON
OFF
ON
OFF
11
ON
ON
OFF
ON
OFF
OFF
OFF
43
ON
ON
OFF
ON
OFF
ON
OFF
12
OFF
OFF
ON
ON
OFF
OFF
OFF
44
OFF
OFF
ON
ON
OFF
ON
OFF
13
ON
OFF
ON
ON
OFF
OFF
OFF
45
ON
OFF
ON
ON
OFF
ON
OFF
14
OFF
ON
ON
ON
OFF
OFF
OFF
46
OFF
ON
ON
ON
OFF
ON
OFF
15
ON
ON
ON
ON
OFF
OFF
OFF
47
ON
ON
ON
ON
OFF
ON
OFF
16
OFF
OFF
OFF
OFF
ON
OFF
OFF
48
OFF
OFF
OFF
OFF
ON
ON
OFF
17
ON
OFF
OFF
OFF
ON
OFF
OFF
49
ON
OFF
OFF
OFF
ON
ON
OFF
18
OFF
ON
OFF
OFF
ON
OFF
OFF
50
OFF
ON
OFF
OFF
ON
ON
OFF
19
ON
ON
OFF
OFF
ON
OFF
OFF
51
ON
ON
OFF
OFF
ON
ON
OFF
20
OFF
OFF
ON
OFF
ON
OFF
OFF
52
OFF
OFF
ON
OFF
ON
ON
OFF
21
ON
OFF
ON
OFF
ON
OFF
OFF
53
ON
OFF
ON
OFF
ON
ON
OFF
22
OFF
ON
ON
OFF
ON
OFF
OFF
54
OFF
ON
ON
OFF
ON
ON
OFF
23
ON
ON
ON
OFF
ON
OFF
OFF
55
ON
ON
ON
OFF
ON
ON
OFF
24
OFF
OFF
OFF
ON
ON
OFF
OFF
56
OFF
OFF
OFF
ON
ON
ON
OFF
25
ON
OFF
OFF
ON
ON
OFF
OFF
57
ON
OFF
OFF
ON
ON
ON
OFF
26
OFF
ON
OFF
ON
ON
OFF
OFF
58
OFF
ON
OFF
ON
ON
ON
OFF
27
ON
ON
OFF
ON
ON
OFF
OFF
59
ON
ON
OFF
ON
ON
ON
OFF
28
OFF
OFF
ON
ON
ON
OFF
OFF
60
OFF
OFF
ON
ON
ON
ON
OFF
29
ON
OFF
ON
ON
ON
OFF
OFF
61
ON
OFF
ON
ON
ON
ON
OFF
30
OFF
ON
ON
ON
ON
OFF
OFF
62
OFF
ON
ON
ON
ON
ON
OFF
31
ON
ON
ON
ON
ON
OFF
OFF
63
ON
ON
ON
ON
ON
ON
OFF
32
OFF
OFF
OFF
OFF
OFF
ON
OFF
64
OFF
OFF
OFF
OFF
OFF
OFF
ON
3.3. Address DIP Switch Setting
ADDRESS is set No 1~128 by DIP switch 1~7.
- ADDRESS Table -
- 7 DIP switched on, it can be set 65 ~ 128 as above.
19
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
<< DOME CAMERA SETUP >>
- DOME DRIVER SET.
- CAMERA SET.
- SPECIAL SET.
- TIME SCHEDULE SET.
- EXIT.
JOYSTICK U/D/L/R TO SELECT.
②
①
3.4. OSD Menu setting
3.4.1. OSD Menu control
■ OSD (ON SCREEN DISPLAY) menu control
It is the function to call up the Menu of the camera.
◈ User can not only set Preset, Group, Tour, Swing, Trace functions of the camera up by the menu,
but also set them up by shortening keys.
■ OSD MENU Enter
The menu is displayed on the screen with the key tone when user presses No.1 and menu key.
■ Cancellation of OSD menu
- Press No. 1 + Menu button.
■ OSD Menu Control
- Move cursor by moving joystick up and down.
- Select Menu or change to setting and move to Joystick left
or right.
20
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
Main menu
Sub menu 1
Sub menu 2
DOME DRIVER SET
SET PTZ FUNCTION
SELECT PRESET
PRESET ID SET
PRESET PTZ SET
SWING SET
GROUP SET CH:01~12
TOUR SET
TRACE SET
PREVIOUS MENU PAGE
RUN PTZ FUNCTION
n/a
SET PRIVACY
MANUAL P/T SPEED
AUTO TILT MOVE
SMART PAN/TILT
RETURN TO MAIN PAGE
CAMERA SET
ID SET
n/a
H-V REVERSE
AGC CONTROL
SHUTTER SPEED
SHARPNESS LEVEL
BRIGHTNESS
COLOR LEVEL
NEXT MENU PAGE
└ DNR LEVEL
└ FOCUS MODE
└ MAX ZOOM LIMIT
└ DSS CONTROL
└ BACK LIGHT MODE
(WDR / HLC / BLC / DEFOG) SET
└ WHITE BALANCE
n/a
└ DAY&NIGHT
└ STABILIZER
└ PREVIOUS PAGE
RETURN TO MAIN PAGE
SPECIAL SET
OSD DISPLAY
n/a
SELECT ALARM
MOTION DETECTION
ALARM CHANNEL ON/OFF
ALARM PRESET SET
AUTO REFRESH TIME
NEXT MENU PAGE
└ USE SHORTCUT KEY
└ RUN DEHUMIDIFICATION
└ LANGUAGE
└ USE PASSWORD
└ CHANGE PASSWORD
└ FACTORY RESET !
└ PREVIOUS PAGE
RETURN TO MAIN PAGE
TIME SCHEDULE SET
SCHEDULE FUNCTION SET
n/a
SCHEDULE BACKLIGHT SET
RESUME TIME SET
HOME POSITION SET
TIME SET
RETURN TO MAIN PAGE
EXIT
n/a
n/a
3.4.2. Menu function
■ OSD Menu tree
21
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
- DOME DRIVER SET.
: Set Pan, Tilt or various surveillance functions.
- CAMERA SET.
: Set Video, screen display functions.
- SPECIAL SET.
: Set motion detection, alarm, multi-language, Password, Factory default
- TIME SCHEDULE SET.
: you can set time schedule for various function in this menu.
- EXIT.
: Out of OSD menu
- DOME DRIVE SET.
1. SET PTZ FUNCTION.
2. RUN PTZ FUNCTION:UNDEF
3. SET PRIVACY.
4. MANUAL P/T SPEED:MIDDLE
5. AUTO TILT MOVE:OFF
6. SMART PAN/TILT:ON
7. RETURN TO MAIN PAGE.
JOYSTICK U/D/L/R TO SELECT.
<< DOME CAMERA SETUP >>
- DOME DRIVER SET.
- CAMERA SET.
- SPECIAL SET.
- TIME SCHEDULE SET.
- EXIT.
JOYSTICK U/D/L/R TO SELECT.
- SET PRESET & RUN.
1. SELECT PRESET CH:001
2. PRESET ID SET
3. PRESET PTZ SET
4. SWING SET
5. GROUP SET CH:01~12
6. TOUR SET
7. TRACE SET
8. PREVIOUS MENU PAGE.
JOYSTICK U/D/L/R TO SELECT.
■ DOME DRIVER SET
1. SET PTZ FUNCTION
Set up or execute Preset, Swing, Group, Tour, Trace.
Select “DOME DRIVER SET" in main menu, then move joystick left / right and display sub menu list.
Select "1. SET PTZ FUNCTION" then move joystick left/right and display various surveillance function
list.
1). SELECT PRESET CH
- Set up preset Number.
- Set up preset No by moving Joystick left / right.
: Number up / : Number down
◈ Set up Max. 250 programmable Preset No.
22
2). PRESET ID SET
- User can set ID of each preset No.
- Select "2. PRESET ID SET" then moves joystick left or
right and displays input of preset ID options.
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
Change letter
After select and
back
After select and
forward
PRESET CH:001[PRESET:001]
! " $ % & ' ( ) * + , - . / 0 1 2 3 4 5 6 7
89 :; <= >? @A BC DE FG HIJ KL MNO
P Q R S TUV W X YZ[ \ ] ^ _ , ab c d e fg
h i j k lm n o p q r s t u v w x yz {ㅣ }~℃
ZOOM(IN/OUT), ID SHIFT.
F/F SAVE, F/N NOT SAVE.
- SET PRESET & RUN.
1. SELECT PRESET CH:001
2. PRESET ID SET
3. PRESET PTZ SET
4. SWING SET
5. GROUP SET CH:01~12
6. TOUR SET
7. TRACE SET
8. PREVIOUS MENU PAGE.
JOYSTICK U/D/L/R TO SELECT.
[SAVE] [DELETE] [RETURN]
F/F SELECT, F/N SHIFT MENU.
PRESET:001
User can select ID letter or icon by using joystick
Up/Down/Right/Left. Shift letter digit by "ZOOM
To save designated ID, Please pressing "F/F" key,
No to save ID, Please press "F/N" key, it doesn’t save
ID and back to previous setting..
3). PRESET PTZ SET
- PRESET setting menu.
"Save “1.SELECT PRESET CH" No and "2. PRESET ID"
Move to menu as desire by moving joystick up/down/left/right.
Press F/N [SAVE] → [DELETE] → [RETURN], Move cursor and select menu by pressing F/F.
• [SAVE] : Save and go to previous screen
• [DELETE] : Delete PRESET
• [RETURN] : Go to previous screen (Cancellation)
4). SWING SET
- The SWING commands the camera to move between 2 selected positions, monitoring the route
.
23
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
: Moves menu
: Changes Setting
1. PAN/TILT SWING
TILT – Move Up and Down.
PAN – Move Left and Right.
2. START PRESET
Set start preset point in Swing.
3. END PRESET
Set end preset point in Swing.
4. SWING TIME
Set duration time between Swing movement .(1~127)
5. SWING SPEED
Set movement speed.(1~64)
[P]
PESET : Enter PRESET No (Save PRESET No)
[S]
SPEED : Set movement speed (1~64) 1<64
[T]
TIME : Set duration time (1~127 sec)
- SWING SET.
1. PAN/TILT SWING
: UNDEF
2. START PRESET
: 000
3. END PRESET
: 000
4. SWING TIME
: 000
5. SWING SPEED
: 000
F/F SAVE, F/N NOT SAVE.
- SET PRESET & RUN.
1. SELECT PRESET CH:001
2. PRESET ID SET
3. PRESET PTZ SET
4. SWING SET
5. GROUP SET CH:01~12
6. TOUR SET
7. TRACE SET
8. PREVIOUS MENU PAGE.
JOYSTICK U/D/L/R TO SELECT.
- SET PRESET & RUN.
1. SELECT PRESET CH:001
2. PRESET ID SET
3. PRESET PTZ SET
4. SWING SET
5. GROUP SET CH:01~12
6. TOUR SET
7. TRACE SET
8. PREVIOUS MENU PAGE.
SELECT (F/F), CHANGE (L/R)
- GROUP SET CH:001
[P]
[S]
[T] [P]
[S]
[T]
000
000
000 000
000
000
000
000
000 000
000
000
000
000
000 000
000
000
000
000
000 000
000
000
000
000
000 000
000
000
000
000
000 000
000
000
F/F SAVE, F/N NOT SAVE.
5). GROUP SET CH: 1~12
User can set up Max. 12 groups and it is included 12 preset points each group.
24
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
Move next menu
Move previous menu
Change setting
- SET PRESET & RUN.
1. SELECT PRESET CH:001
2. PRESET ID SET
3. PRESET PTZ SET
4. SWING SET
5. GROUP SET
6. TOUR SET
7. TRACE SET
8. PREVIOUS MENU PAGE.
JOYSTICK U/D/L/R TO SELECT.
- TOUR SET.
T01:00
T02:00
T03:00
T04:00
T05:00
T06:00
T07:00
T08:00
T09:00
T10:00
T11:00
T12:00
F/F SAVE, F/N NOT SAVE.
- SET PRESET & RUN.
1. SELECT PRESET CH:001
2. PRESET ID SET
3. PRESET PTZ SET
4. SWING SET
5. GROUP SET
6. TOUR SET
7. TRACE SET
8. PREVIOUS MENU PAGE.
JOYSTICK U/D/L/R TO SELECT.
- TRACE SET.
[SET] [SAVE] [DELETE] [RETURN]
F/F SELECT, F/N SHIFT MENU.
6). TOUR SET
Tour is included 12 groups.
7). TRACE SET
Save joystick pattern movement for Max. 180 seconds and execute save joystick movement. .
25
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
: SWING
: GROUP
: TOUR
: TRACE
- PRIVACY ZONE SET.
CH 01:
SET
CH 02:
BLANK
CH 03:
BLANK
CH 04:
BLANK
CH 05:
BLANK
CH 06:
BLANK
CH 07:
BLANK
CH 08:
BLANK
PREVIOUS MENU PAGE.
SELECT (F/F), CHANGE (L/R)
- DOME DRIVE SET.
1. SET PTZ FUNCTION.
2. RUN PTZ FUNCTION:UNDEF
3. SET PRIVACY.
4. MANUAL P/T SPEED:MIDDLE
5. AUTO TILT MOVE:OFF
6. SMART PAN/TILT:ON
7. RETURN TO MAIN PAGE.
JOYSTICK U/D/L/R TO SELECT.
- DOME DRIVE SET.
1. SET PTZ FUNCTION.
2. RUN PTZ FUNCTION:UNDEF
3. SET PRIVACY.
4. MANUAL P/T SPEED:MIDDLE
5. AUTO TILT MOVE:OFF
6. SMART PAN/TILT:ON
7. RETURN TO MAIN PAGE.
↓
■ TRACE Set
① "7. TOUR SET"
② Press F/N button to select “SET” mode → move camera by using joystick toward position you want
up to for 180/sec
③ After finishing all work, move cursor to save mode → press F/N button to save joystick movement
• [SET] : Start TRACE set up
• [SAVE] : Save and previous OSD screen
• [DELETE] : Delete TRACE
• [RETURN] : Go to previous OSD screen (Cancellation)
8). "PREVIOUS MENU PAGE" - It is back to previous menu screen by moving joystick right.
2. RUN PTZ FUNCTION
It is executed various surveillance function by DVR
without keyboard.
"2. RUN PTZ FUNCTION"
Select desired function,
SWING - GROUP - TOUR TRACE by moving joystick
right / left.
Select desired function and out of OSD menu, it is
executed selected function automatically.
Display selected function icon in the screen.
3. SET PRIVACY
Max 8 programmable privacy zones can be configured for the protection of privacy.
26
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
Move screen
Reduce size
Enlarge size
SET
ON
OFF
DEL
Set new
privacy area
Display
privacy area
Hide privacy
area
Remove
privacy area
Caution) Not enable to set under 45 degree for PRIVACY ZONE accuracy
┌
┑
└
┘
SET PRIVACY:01
SAVE(F/F), ESC(F/N), MASK(ZOOM)
- PRIVACY ZONE SET.
CH 01:
OFF
CH 02:
BLANK
CH 03:
BLANK
CH 04:
BLANK
CH 05:
BLANK
CH 06:
BLANK
CH 07:
BLANK
CH 08:
BLANK
■ Setting
- DOME DRIVE SET → SET PRIVACY → Enter PRIVACY ZONE SET Mode
Move Joystick up / down at desired channel then display black box In the middle of
screen by pressing “F/F” key.
- Move camera position where you want to hide
- Select privacy zone size by using zoom IN/OUT.
- Set up Privacy zone – adjust box size – Save Privacy
setting by “F/F” key then back to previous menu
If press “F/N” key, it doesn’t save privacy zone setting and back to previous screen..
- It is changed SET - ON - OFF – DEL in order each
privacy setting channel by moving joystick left / right.
- Select desired mode and execute selected menu by
pressing F/F.
4. MANUAL P/T SPEED
User can control the maximum speed in controlling of up and down; The mode is Low, Medium, Max
5. AUTO TILT MOVE
The PAN is turned in a 180° degree arc automatically when the angle of the camera moves down to the
maximum degree, therefore, it is possible to track objects continuously
6. SMART PAN/TILT
This function makes the Pan/Tilt speed automatically as zoom magnification.
27
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
- CAMERA SET.
1. ID SET(PRESS F/F KEY).
2. H-V REVERSE
: NORMAL
3. AGC CONTROL
: ON
4. SHUTTER SPEED
: AUTO
5. SHARPNESS LEVEL
: 07
6. BRIGHTNESS LEVEL
: 08
7. COLOR LEVEL
: 05
7. NEXT MENU PAGE.
8. RETURN TO MAIN PAGE.
JOYSTICK U/D/L/R TO SELECT.
<< DOME CAMERA SETUP >>
- DOME DRIVER SET.
- CAMERA SET.
- SPECIAL SET.
- TIME SCHEDULE SET.
- EXIT.
JOYSTICK U/D/L/R TO SELECT.
SET ID[_ CAM-000]
! " $ % & ' ( ) * + , - . / 0 1 2 3 4 5 6 7
89 : ; < = > ? @ A B C D E F G HIJ KL MNO
P Q R S TU V W X YZ [\ ] ^ _ , ab c d e f g
h i j k lm n o p q r s tu v w x y z{ ㅣ }~℃
ZOOM(IN/OUT), ID SHIFT.
F/F SAVE, F/N NOT SAVE.
- CAMERA SET.
1. ID SET(PRESS F/F KEY).
2. H-V REVERSE
: NORMAL
3. AGC CONTROL
: ON
4. SHUTTER SPEED
: AUTO
↓
- CAMERA SET.
1. ID SET(PRESS F/F KEY).
2. H-V REVERSE
: NORMAL
3. AGC CONTROL
: ON
4. SHUTTER SPEED
: AUTO
↓
■ CAMERA SET
1. ID SET
It is set camera ID up to 16 English letters it is enable to
select desired letter by joystick zoom and save camera ID
by F/F key and out of menu.
2. H-V REVERSE
Set up H-V reverse mode.
.
● Normal
● H-REV: Flip the picture horizontally on the
screen.
● V-REV: Flip the picture vertically on the screen.
● HV-REV : Flip the picture horizontally and
vertically on the screen.
3. AGC CONTROL
AGC(Automatic Gain Control)- It adjusts the
amount of video amplification to maintain a full 1-volt
peak-to-peak video signal output automatically.
▶ ON, OFF
28
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
- CAMERA SET.
1. ID SET(PRESS F/F KEY).
2. H-V REVERSE
: NORMAL
3. AGC CONTROL
: ON
4. SHUTTER SPEED
: AUTO
↓
1. ID SET(PRESS F/F KEY).
2. H-V REVERSE
: NORMAL
3. AGC CONTROL
: ON
4. SHUTTER SPEED
: AUTO
5. SHARPNESS LEVEL
: 07
↓
↑
2. H-V REVERSE
: NORMAL
3. AGC CONTROL
: ON
4. SHUTTER SPEED
: AUTO
5. SHARPNESS LEVEL
: 07
6. BRIGHTNESS LEVEL
: 08
7. COLOR LEVEL
: 05
8. NEXT MENU PAGE.
↓
↑
2. H-V REVERSE
: NORMAL
3. AGC CONTROL
: ON
4. SHUTTER SPEED
: AUTO
5. SHARPNESS LEVEL
: 07
6. BRIGHTNESS LEVEL
: 08
↓
4. SHUTTER SPEED
Adjust camera electronic Shutter speed.
Factory default: Auto.
▶ Range : A.FLICKER, AUTO, 1/50,60~1/30000
5. SHARPNESS LEVEL
Compensation of the shape of a subject.
▶ Range : 1 ~ 10, Default : 07
6. BRIGHTNESS LEVEL
Control brightness of a screen.
The screen gets dark because an iris is closed as
the numerical value is low, whereas the screen gets
bright because an iris is opened as the numerical
value is high.
.
▶ Range : 0~20, Default: 08
7. COLOR LEVEL
It adjusts the chroma(=colorfulness) of image. As
the number gets lower, the chroma gets lower and
nearer to black. As the number gets higher, the color
gets deeper.
.
▶ Range : 0~20, Default : 05
8. NEXT MENU PAGE.
▶ Go to next menu page.
9. RETURN TO MAIN PAGE.
▶ Go to previous menu.
29
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
- CAMERA SET.
10. DNR LEVEL
: AUTO
11. FOCUS MODE
: AUTO
12. MAX ZOOM LIMIT
: x10
13. DSS CONTROL
: OFF
↓
- CAMERA SET.
10. DNR LEVEL
: AUTO
11. FOCUS MODE
: AUTO
12. MAX ZOOM LIMIT
: x10
13. DSS CONTROL
: OFF
↓
- CAMERA SET.
10. DNR LEVEL
: AUTO
11. FOCUS MODE
: AUTO
12. MAX ZOOM LIMIT
: x10
13. DSS CONTROL
: OFF
14. BACK LIGHT MODE
: OFF
↓
- CAMERA SET.
10. DNR LEVEL
: AUTO
11. FOCUS MODE
: AUTO
12. MAX ZOOM LIMIT
: x10
13. DSS CONTROL
: OFF
14. BACK LIGHT MODE
: OFF
15. WHITE BALANCE
: AUTO
↓
10. DNR LEVEL
Reduce noise of minimum illumination and also file
size becomes smaller while DVR is being recorded by
the effective reduction of noise.
▶ OFF, LOW, MIDDLE, MAX, AUTO
◈ cf. Not available under AGC off
11. FOCUS MODE
Change Focus Mode to hand-worked or auto.
▶ MANUAL : User can set focus manually.
▶ AUTO : Execute Auto focus as subject movement
▶ ONE SHOT : Auto Focusing mode works while
zoom is worked
12. MAX ZOOM LIMIT
It is used when user corrects and limits the
extensional range of the focus as a function to set the
maximum value of zoom. (Available to set DIGITAL
ZOOM range)
▶ x10(Optical zoom): MAX ZOOM LIMIT OFF status
▶ x320(dz) → (Digital zoom)
13. DSS CONTROL
An object becomes clear as the field value gets higher in Illumination, Max. 4 field, whereas a moving
object becomes dim.
▶ Range : Off, 2 ~ 32 fields
14. BACK LIGHT MODE
It provides clear images of object and back ground
against a severe back light.
▶ OFF : Disables the BACKLIGHT
▶ WDR : Activates back light. Compensate
▶ HLC(High Light Compensation) : Activates High
Light back light Compensate
▶ BLC: Activates a Use defined back light
compensation.
▶ DEFOG : Compensates the fog level.
Select desired Back light mode by “F/F" key.
30
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
Move BLC area
Reduce BLC
area
Enlarge BLC area
- WDR SET.
1. WDR LEVEL
: MIDDLE
RETURN TO MENU.
- HLC SET.
1. HLC LEVEL
: MIDDLE
2. HLC COLOR
: BLACK
RETURN TO MENU.
- BLC AREA SET.
F/F SAVE, F/N NOT SAVE.
- DEFOG SET.
1. DEFOG MODE
: AUTO
2. DEFOG LEVEL
: MIDDLE
RETURN TO MENU.
WDR SET
- WDR LEVEL: Set WDR sensitivity, Low or Middle or Max. .
HLC (High Light Compensation) SET
- HLC LEVEL: Set HLC level LOW, MIDDLE, MAX.
- HLC COLOR : Set GRAY, D.GRAY, BLACK.
The highlighted image changes into gray, D. gray and black.
BLC SET
- BLC AREA SET
① 13.BACK LIGHT MODE → Enter BLC area set menu by pressing “F/F” key in BLC MODE.
② It is enables to move BLC area, reduce BLC area and enlarge BLC area by Joystick ZOOM IN/OUT
31
DEFOG SET
When fog, smog, etc cause the degradation of
surveillance function, DEFOG helps restore the clear-cut
image.
- DEFOG MODE: MANUAL / AUTO
- DEFOG LEVEL: LOW / MIDDLE / MAX
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
↑
14. BACK LIGHT MODE
: OFF
15. WHITE BALANCE
: AUTO
16. DAY&NIGHT
: AUTO SLOW
17. STABILIZER
: OFF
18. PREVIOUS MENU PAGE.
JOYSTICK U/D/L/R TO SELECT.
↑
12. MAX ZOOM LIMIT
: x30
13. DSS CONTROL
: OFF
14. BACK LIGHT MODE
: OFF
15. WHITE BALANCE
: AUTO
16. DAY&NIGHT
: AUTO SLOW
17. STABILIZER
: OFF
18. PREVIOUS MENU PAGE.
JOYSTICK U/D/L/R TO SELECT.
15. WHITE BALANCE
The white balance menus adjusts the balance of the screen colors under differnet lighting condition.
▶ AUTO: Compensates the color automatically.
▶ INDOOR: Compensates the color to fit the indoor environment.
▶ OUTDOOR: Compensates the color to fit the outdoor environment.
16. DAY&NIGHT
The Day & Night function allows the camera to
switch between color and B/W mode. it is set optimal
condition by DSS control function.
▶ NIGHT MODE : B/W Mode most times.
▶ AUTO SLOW : Operates in DAY&NIGHT mode
under low illumination.
▶ AUTO FAST : Operates in DAY&NIGHT mode
high illumination.
▶ DAY MODE : COLOR mode most times.
※ Default is AUTO SLOW, It keeps color mode
most times under AUTO SLOW.
17. STABILIZER
There is some tremble as zoom magnification is
high, the function can compensate the tremble.
▶ ON / OFF
Select “ON”, it is fixed x30 optical zoom
magnification in 13.MAX ZOOM LIMIT.
(Not available in Digital zoom).
18. PREVIOUS MENU PAGE
Back to previous screen.
32
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
Caution) Keep icon in the screen in any condition.
- SPECIAL SET.
1. OSD DISPLAY
: ID+STATUS
2. SELECT ALARM
: SENSOR
3. MOTION DETECTION
: OFF
4. ALARM CHANNEL ON/OFF.
5. ALARM PRESET SET
6. AUTO REFRESH TIME
: 3 Day
7. NEXT MENU PAGE.
8. RETURN TO MAIN PAGE.
JOYSTICK U/D/L/R TO SELECT.
<< DOME CAMERA SETUP >>
- DOME DRIVER SET.
- CAMERA SET.
- SPECIAL SET.
- TIME SCHEDULE SET.
- EXIT.
JOYSTICK U/D/L/R TO SELECT.
- SPECIAL SET.
1. OSD DISPLAY
: ID+STATUS
2. SELECT ALARM
: MOTION
3. MOTION DETECTION
: ON
4. ALARM CHANNEL ON/OFF.
5. ALARM PRESET SET
6. AUTO REFRESH TIME
: 3 Day
7. NEXT MENU PAGE.
8. RETURN TO MAIN PAGE.
PRESS F/F, AREA OR LINE SET.
- MOTION DETECTION AREA SET.
F/F SAVE, F/N NOT SAVE.
■ SPECIAL SET
1. OSD DISPLAY
Display ID or Status in the screen
● ID + STATUS: Display ‘ID’ & ‘Status’ only
● ID ONLY: Display only ‘ID’
● STATUS ONLY: Display ‘Status’ only
● ALL OFF: None display
2. SELECT ALARM
Enable to select Alarm sensor type.
▶ Sensor / Motion
3. MOTION DETECTION
Detect if the movement is recognized in designated area, it is display “Motion detected” message in the
screen and beep sound in the keyboard.
PTZ function doesn’t perform when motion detection is “On”, Motion detection is detected specific
area’s movement, if the cameras moves Pan, Tilt and zoom, it doesn’t recognize the motion detection
correctly.
33
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
Move motion
detection area
Reduction
motion
detection area
Enlarge
motion
detection area
- SPECIAL SET.
1. OSD DISPLAY
: ID+STATUS
2. SELECT ALARM
: SENSOR
3. MOTION DETECTION
: OFF
4. ALARM CHANNEL ON/OFF.
5. ALARM PRESET SET
6. AUTO REFRESH TIME
: 3 Day
7. NEXT MENU PAGE.
8. RETURN TO MAIN PAGE.
JOYSTICK U/D/L/R TO SELECT.
- ALARM CHANNEL ON/OFF.
CH 01:
OFF
CH 02:
OFF
CH 03:
OFF
CH 04:
OFF
ALARM RELAY
: OFF
ACTIVE ALARM
: OPEN
PREVIOUS MENU PAGE.
■ Set up motion detection
① "2. SELECT ALARM". Select “motion”.
② "3. MOTION DETECTION" select "ON" Change to screen for motion detection area set mode by
pressing F/F key.
③ Set motion detection area by joystick
and adjust motion detection area size
by joystick Zoom IN/OUT.
④ Save motion detection setting and
back to previous menu by pressing
“F/F".
Select MOTION DETECTION : “On” it is displayed “Motion Detected’ message in the screen if motion
is detected in designated motion detection area.
4. ALARM CHANNEL ON/OFF
- Set Alarm input On/Off each channel.
- ALARM CH On/Off : Alarm Input – Each channel can be ON/OFF.
- According to signal connection, user can select ACTIVE OPEN(N/C) or ACTIVE CLOSE(N/O).
- If the user selects ACTIVE OPEN, it is activated when Alarm input is open, if the user selects ACTIVE
Close, it is activated when Alarm input is Close
5. ALARM PRESET SET
- The camera can move to a preset point automatically when the wrong signal is sensed in each ALRAM
CHANNEL.
- Set a preset point firstly to move, if wrong signal is sensed, then use that sets the preset number into
each ALARM CHANNEL.
- Select ALARM Channel “OFF” and doesn’t move relevant preset point
- User can select PRESET Point number 1 to 250 and set it.
34
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
- SPECIAL SET.
9. USE SHORTCUT KEY
: ON
10. RUN DEHUMIDIFICATION.
11. LANGUAGE
: ENGLISH
12. USE PASSWORD
: OFF
13. CHANGE PASSWORD.
14. FACTORY RESET ! WARNING!
15. PREVIOUS PAGE.
JOYSTICK U/D/L/R TO SELECT.
- SPECIAL SET.
1. OSD DISPLAY
: ID+STATUS
2. SELECT ALARM
: SENSOR
3. MOTION DETECTION
: OFF
4. ALARM CHANNEL ON/OFF.
5. ALARM PRESET SET
6. AUTO REFRESH TIME
: 3 Day
7. NEXT MENU PAGE.
8. RETURN TO MAIN PAGE.
JOYSTICK U/D/L/R TO SELECT.
- ALARM PRESET SET.
CH 01:
001
CH 02:
002
CH 03:
003
CH 04:
004
PREVIOUS MENU PAGE.
- It is checked exist Alarm status in the keyboard, if it is sensed wrong signal, the keyboard makes beep
sound and the security manager can check Alarm position status.
When many cameras’ alarm are checked, it might take time to transmit signal to Control keyboard when
alarm is detected but the camera moves specific preset position automatically.
Please refer to CONTROL KEYBOARD user manual
6. AUTO REFRESH TIME
- Initialize automatically for focus normal movement.
▶ OFF, 6hours~18hours, 1day~7days.
◈ Focus initialize pressing F/F key
7. NEXT MENU PAGE.
▶ Go to the next page.
8. RETURN TO MAIN PAGE.
▶ Go to previous page.
9. USE SHORTCUT KEY
- The Shortcut Key can make some of the functions to
perform faster and easily.
▶ ON : Use shortcut key
▶ OFF : Not use Shortcut key
35
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
Function
Operation
Function
Operation
Group 1
51 + Preset
Run Tilt Swing
65 + Preset
Group 2~11
52 ~61 + Preset
Run Trace
66 + Preset
Group 12
62 + Preset
Run Spiral
67 + Preset
Run Tour
63 + Preset
OSD Menu ON/OFF
95 + Preset
Run Pan Swing
64 + Preset
Caution) it is able to perform the functions in all protocol type
- SPECIAL SET.
9. USE SHORTCUT KEY
: ON
10. RUN DEHUMIDIFICATION.
11. LANGUAGE
: ENGLISH
12. USE PASSWORD
: ON
13. CHANGE PASSWORD.
14. FACTORY RESET ! WARNING!
15. PREVIOUS PAGE.
JOYSTICK U/D/L/R TO SELECT.
- PASSWORD:0000
JOYSTICK U/D/L/R TO SELECT.
PRESS F/F ENTER, F/N EXIT.
It is available to set Dehumidification under D-max
protocol by D-max brand keyboard; it is displayed icon
on the screen.
■ Short cut key menu
10. RUN DEHUMIDIFICATION (In case of indoor type fan only operates)
- When the camera is installed under hush weather condition, it is hard to monitoring the subject due to
moisture condense on the clear glass, to remove Moisture condense, the user can use Dehumidification
which operate fan and heater for 10 min. The function stops after activating it for 10min automatically but
if you want to use Dehumidification again, you could select the function in the OSD. .
▶Turn ON : 1 + AUX1 + ON
OFF : 1 + AUX1 + OFF
11. LANGUAGE
- Multi-language
▶ English
12. USE PASSWORD
36
Designate User password for PTZ operation security.
- "12.Select USE PASSWORD" ON/OFF by
Joystick.
- Select Use password “ON”, display Password
question in the screen before the user enter OSD
menu
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
Caution) Remove exist setting in the menu.
Caution) if user forget password, it would use Hidden password
Hidden password: 7233, Please change to Password for security.
- SPECIAL SET.
9. USE SHORTCUT KEY
: ON
10. RUN DEHUMIDIFICATION.
11. LANGUAGE
: ENGLISH
12. USE PASSWORD
: OFF
13. CHANGE PASSWORD.
14. FACTORY RESET ! WARNING!
15. PREVIOUS PAGE.
JOYSTICK U/D/L/R TO SELECT.
- CHANGE PASSWORD.
OLD PASSWORD : 0000
NEW PASSWORD: 0000
JOYSTICK U/D/L/R TO SELECT.
F/F SAVE, F/N NOT SAVE.
13. CHANGE PASSWORD
- "13. CHANGE PASSWORD" the user can select password by Joystick Left / Right.
- Initial Password is “0000”, New Password is designated by Joystick UP/Down/Left/Right.
- F/F key : it saves the password and back to previous menu.
- F/N key : it doesn’t save Password and back to previous menu.
14. FACTORY RESET
Set factory default same as initialization setting.
37
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
Move Menu:
Change Setting
Value:
※ Either PAN or TILT can be set for SWING.
※ [START~END] indicates the hour/minute and the time is set within 24 hours.
※ PRESET, GROUP, SWING, TOUR, TRACE, DEFOG can be overlapped in [FUNCTION]1~6.
Beware of malfunction when time is overlapped.
- TIME SCHEDULE SET.
1. SCHEDULE FUNCTION SET.
2. SCHEDULE BACKLIGHT SET.
3. RESUME TIME SET
: OFF
4. HOME POSITION SET
: OFF
5. TIME SET.
6. RETURN TO MAIN PAGE.
-TIME: 00:00:00
JOYSTICK U/D/L/R TO SELECT.
<< DOME CAMERA SETUP >>
- DOME DRIVER SET.
- CAMERA SET.
- SPECIAL SET.
- TIME SCHEDULE SET.
- EXIT.
JOYSTICK U/D/L/R TO SELECT.
- SCHEDULE FUNCTION SET.
[FUNCTION]
[NO]
[STSRT~END]
1.PRESET
OFF
00/00~00/00
2.GROUP
OFF
00/00~00/00
3.SWING
OFF
00/00~00/00
4.TOUR
OFF
00/00~00/00
5.TRACE
OFF
00/00~00/00
6.DEFOG
OFF
00/00~00/00
7.DEHUMIDITY
OFF
00/00
8.LENS INIT
OFF
00/00
9.PREVIOUS MENU PAGE.
JOYSTICK U/D/L/R TO SELECT.
■ TIME SCHEDULE SET
1. SCHEDULE FUNCTION SET
Set to operate the functions for various surveillance,
dehumidification, etc., in the designated time.
Select TIME SCHEDULE SET > SCHEDULE FUNCTION SET in order.
1. Setting PRESET, GROUP & SCHEDULE: Select
PRESET or GROUP by moving the Joystick up &
down in [FUNCTION]. Select the saved PRESET No.
or GROUP No. in [NO] and then set the operating
start time and the stop time for PRESET or GROUP
in [START~END].
2. Setting SWING SCHEDULE: Select SWING in [FUNCTION]. Select PAN or TILT in [NO] and then set
the operating start time and the stop time for SWING in [START~END].
3. Setting TOU and TRACE SCHEDULE: Select TOUR or TRACE in [FUNCTION]. Select ON or OFF in
[NO] and then set the operating start time and the stop time for TOUR or TRACE in [START~END].
4. Setting DEFOG SCHEDULE: Select DEFOG in [FUNCTION]. Select MANUAL or AUTO in [NO] and
38
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
※ Beware of malfunction in case the time setting of BACKLIGHT 1,2,3 is overlapped.
※ LENS INIT is for maintaining the lens in the constantly optimized condition when operating the
autofocus function under the optimization of the lens motor.
※ Use this function in the specific time when the dehumidification is needed.
- TIME SCHEDULE SET.
1. SCHEDULE FUNCTION SET.
2. SCHEDULE BACKLIGHT SET.
3. RESUME TIME SET
: 003
4. HOME POSITION SET
: 003
5. TIME SET.
6. RETURN TO MAIN PAGE.
-TIME: 00:00:00
JOYSTICK U/D/L/R TO SELECT.
- SCHEDULE BACKLIGHT SET.
[BACKLIGHT]
[NO]
[STSRT~END]
1.WDR
OFF
00/00~00/00
2.HLC
OFF
00/00~00/00
3.BLC
OFF
00/00~00/00
4.PREVIOUS MENU PAGE.
JOYSTICK U/D/L/R TO SELECT.
then set the operating start time and the stop time for DEFOG in [START~END].
5. Setting DEHUMIDITY(=DEHUMIDIFICATION) SCHEDULE: When the operating start time is set with
DEHUMIDITY function 'ON', the fan & heater will work for 10 minutes on time.
6. Setting LENS INITIAL SCHEDULE: The zoom and the focus of LENS are initialized in the setting time.
- Set LENS INIT to 'ON' and then the operating time.
2. SCHEDULE BACKLIGHT SET
This function makes the set Back Light Compensation worked in the designated time.
- After adjusting to ‘ON’ one function to operate for a fixed time among WDR/HLC/BLC and then set the
operating start time & the stop time. When operating on SCHEDULE function and stopping, it operates
as set in the BACKLIGHT function of CAMERA SET.
39
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
EX). When the PRESET of SCHEDULE FUNCTION SET is set to 00:00~23:59, the camera always
moves back to home position after the setting time in alarming or manual operation.
This Icon is displayed in the screen when it is set Resume Time.
When Resume time is set, it is not enable to set PRESET, GROUP, TOUR or SWING, If
the user want to set the function, Resume time function have to be “OFF” then the user
can set the desired function.
- TIME SCHEDULE SET.
1. SCHEDULE FUNCTION SET.
2. SCHEDULE BACKLIGHT SET.
3. RESUME TIME SET
: 003
4. HOME POSITION SET
: 003
5. TIME SET.
6. RETURN TO MAIN PAGE.
-TIME: 00:00:00
JOYSTICK U/D/L/R TO SELECT.
- TIME SCHEDULE SET.
1. SCHEDULE FUNCTION SET.
2. SCHEDULE BACKLIGHT SET.
3. RESUME TIME SET
: 003
4. HOME POSITION SET
: 003
5. TIME SET.
6. RETURN TO MAIN PAGE.
-TIME: 00:00:00
JOYSTICK U/D/L/R TO SELECT.
3. RESUME TIME SET
It can select the delay time that the camera move to
the place alarming to observe where wrong signal is
sensed.
User can set it for 1sec to 180sec and operate
GROUP, TOUR, SWING again in a preset time.
SWING, GROUP, TOUR are operated in a preset time
when user stops the operating joystick in the case of
not connecting with the ALARM
4. HOME POSITION SET
This function shows that when the abnormal sign
happens in the execution of PRESET in SCHEDULE
FUNCTION SET, the camera can move to and surveil
Alarm position, and select the staying time. In
addition, even after it works manually or the PRESET
is run, the executed SCHEDULE PRESET operates
again after this setting time. The user can designate
the time from 3 to 180 seconds. When the setting time
passes, the PRESET of SCHEDULE FUNCTION is run
again.
40
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
Move Menu
Change Setting Value
※ As it’s not a network product, time can be changed a little when using it for a long time. After the
blackout or one to three-hour power-off, time can be compensated, but when operating again and
using it in the long-time power-off, please be sure to check time.
- After completing the setting, please press F/F key for saving.
- TIME SCHEDULE SET.
1. SCHEDULE FUNCTION SET.
2. SCHEDULE BACKLIGHT SET.
3. RESUME TIME SET
: 003
4. HOME POSITION SET
: 003
5. TIME SET.
6. RETURN TO MAIN PAGE.
-TIME: 00:00:00
JOYSTICK U/D/L/R TO SELECT.
- TIME SET.
1.CHANGE TIME : 00/00/00
2. TIME COMPENSATION : 000S/24H
JOYSTICK U/D/L/R TO SELECT.
F/F SAVE, F/N NOT SAVE.
5. TIME SET
This function can set the operating time and the time compensation.
-When moving the joystick right and left in '5.TIME SET', 'TIME SET' appears on the screen .
1). CHANGE TIME: Set the time in order of hour/minute/second.
2). TIME COMPENSATION: Compensate the time error when operating for a long time. You can set it in
seconds, even in positive numbers and negative numbers. (Based on 24 hours)
ex). 001S/24H → Compensate time one second faster a day(Max. -59 seconds)
-02S/24H → Compensate time two seconds later a day(Max. -60 seconds)
41
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
Ex) Delete No 5 Preset
(Holding 3 seconds)
(holding 3 seconds)
Set up duration time (1~127
sec) after movement
Set up movement
speed (1~64sec)
3.4.3. Set-up menu, Execute and delete by keyboard
1. Preset Setting
Save Max. 250 Preset points
① Preset set up
② Preset movement
Move designated preset position after press Preset No and
P-SET button.
③ Each Preset movement
Press button for 3 sec then beep sound, it follows the steps as below.
④ All Preset Movement
Press button for 3 sec then beep sound,
it follows the steps as below
2. Swing Setting
① Swing set
② Swing execute ③ Swing stop
42
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
3. Group setting
① Start Group setting mode
To set more preset, enter preset No and set same process.
Set a GROUP again from the first after ending with , if user wants to finish Preset input in one Group to input
another Group.
② Group execute ③ Group stop
4. Tour setting
① Tour set mode
43
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
(Holding 3 seconds ~)
② Tour execute/Stop ③ Tour remove
5. Spiral Function
It is a function to observe objects automatically in the spiral direction.
Spiral On ② Spiral Off
* 26. “67+PRESET key” is also available in Shortcut key ‘On’ mode
6. PTZ Trace
It memorizes P/T/Z motions for 200sec then operates them at the same Trace.
① ▪ Trace execute/Stop ▪ Cancellation:
② Trace setting ③ Trace Cancellation
* 26. “66+PRESET key” is also available in Shortcut key ‘On’ mode
44
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
CAM-001
SAVE PRESET:001
CAM-001
PRESET:001
CAM-001
CLEAR PRESET:001
Display SWING execute in
the screen.
CAM-001
SET GP:01 P001,T001,S64, CNT01
As the message in the time of
operation of GROUP SET,
“GP:01” means group No.1,
"P001" means Preset No1,
"T001"means duration time 1 sec
"S64" means movement speed 64,
"CNT01" means set-up preset points
(1 group is consist of 12 preset
points)
CAM-001
SAVE GROUP:01
As the message in the time of
completion of GROUP SET
CAM-001
[SWING] PRESET:001
CAM-001
[GROUP:01] PRESET:001
User can check that Preset
No.1 is saved as an appeared
message in Preset set.
It appears when moving to the
preset No.1.
It appears when user deletes
PRESET No.1. The message
‘All clear PRESET’ is displayed
when user delete PRESER data
It is displayed in the time of
operation of Group and preset
No.
3.4.4. OSD Message Description
1. PRESET Message
2. SWING Message
3. GROUP Message
45
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
CAM-001
Set Tour GP:01
CAM-001
CLEAR TOUR&GROUP.
It shows the data in GROUP and
TOUR saved was deleted.
As the message in the time of
operation of Tour set, “GP:01”
means GROUP No.1 and it shows
that GROUP No.1 was saved.
CAM-001
[TOUR&GP:01] PRESET:001
CAM-001
[RUN SPIRAL]
As the message in the time of
operation of Tour RUN, it will show
that moving to
PRESET No.1 in GRIOUP No.1.
-RUN SPIRAL : It is the Message in the time of operation
of SPIRAL SEQUENCE.
It observe all area of an object in three
dimensions that SPIRAL SEQUENCE
CAMERA moves to upper then down
slowly in a spiral direction.
4. TOUR Message
5. SPIRAL Message
46
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
STATUS
CHECK POINT
TROUBLE SHOOTING
Power is not turned on.
Does the electric power supply into
the product well?
Check the POWER LED is “ON” at the
BOTTOM COVER.
Does not work in Power On.
In operating, does the LED beside
POWER SW light on red?
Check the status of DATA CABLE, if it is not lit.
Check ADDRESS and DIP SW of
communication speed setting, if it is not lit.
Have you selected to RS485 or
RS422 right?
Check the status of OPTION DIP SW No.2
Poor condition of PAN/TILT
Have you turned the ending terminal
register ‘ON’?
Turn ‘ON’ the ending terminal register of the
camera which is set in farthest away.
A image is not clear or black
lines are displayed on the
screen.
Is the power adapter AC24V, 1.5A
over?
Exchange the adapter to for an adapter which
has higher current.
The message ‘P/T POSITION
ERROR’ is displayed
continuously.
Is the camera pressed by something
heavy or put it between others?
Check that a rotation of the camera’s body
works smoothly and remove a object that
hinders the operation of the camera.
The message ‘SORRY NOT
MEMORY’ is displayed
continuously.
Have you set the related functions?
Please refer to the manual book and setting the
function you want.
ALARM RELAY is not
changed to ‘ON’ in the state
of being alarmed.
Have you set the ALARM RELAY ‘ON’
in the SET MODE?
Make sure ALARM RELAY ‘ON’ in the SET
MODE.
In abnormal condition, even if
the sensor is well.
Is it correct ALARM ACTIVE setting
status and the sensor is either opened
or closed?
Fit ALARM ACTIVE MODE setting with the
connection of the SENDOR in the SET
MODE.(It means either sensor is opened or
closed)
PRESET point is different or
out of moving when the
ALARM occurs. The warning
does not work from the
keyboard when the ARLAM
occurs.
Have you set ALARM PRESET in
the SET MODE?
Check the status of the ALARM PRESET
setting in the SET MODE.
Have you used the exclusive control
keyboard?
The warning is only reacted to the
exclusive control keyboard.
YES.
Make sure ALARM “ON” of the camera.
4. TROUBLE SHOOTING
CAUTION IN USE
• Make sure that turn the power switch off before installation.
• Avoid the places where is the high/low temperature and humid.
• Power supply must be min AC24V/2A.
• Please be careful of that you connect respective wires without mismatching in installation.
• Supply to power sources after checking the state of insulation of cables which is connected to the exterior
• Please keep the product from a strong shock or vibration which is the cause of troubles.
Checking in under using
Check the product as following, if something is wrong in installation or using.
47
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
5. Dimension
5.1. Outdoor type
■ Installing wall mount bracket
■ Installing Ceiling Mount Bracket
Unit : mm
48
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
5.2. Indoor type
Unit : mm
49
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
(Control camera OSD by DVR)
6. Configuration diagram
• CAMERA + DVR + MONITOR
• Camera + DVR + Monitor + Controller
50
2Mega TVI & AHD Hybrid Mini Speed Dome Camera User manual
MODEL
TVI & AHD Hybrid Mini Speed Dome Camera
Outdoor
Indoor
Video
Image Sensor
1/3” 2Mega Panasonic CMOS
Scan mode
Progressive Scan
Total number of pixels
1,956(H) x 1,266(V), 2.4M Pixels
Number of active pixels
1,944(H) x 1,213(V), 2.3M Pixels
Resolution
1080P
Minimum illumination
Color : 0.5 lux , BW : 0.1lux
Min. 0.003Lux with DSS(32x)
Video Output
TVI/AHD Selectable
S/N Ratio
More than 52dB
Lens
Lens
5.1~51mm(10x), F1.6 (wide) ~ F1.8 (tele)
Optical(10x), Digital Zoom(32x), Total Zoom (320x)
Focus mode
Auto / Manual / Oneshot
Angle of view
H:54°(Wide)~4.9°(Tele), V:31°(Wide)~4°(Tele)
Pan/ Tilt
Pan/Tilt angle
360° Endless / 92°
Pan Speed
0.1° ~ 240°/sec (64 Levels), Preset: 360°/sec
Preset point
250 Presets
Alarm in/out
4 Inputs / 1 Relay Output
Function
Day & Night
Day / Auto Slow / Auto Fast / Night
Back Light
Off / HLC / BLC / DWDR
White Balance
Auto / Indoor/ Outdoor
AGC
On/Off
DNR
Low / Middle / Max
Privacy / Motion
8Zones / 1Zones
Brightness
Level Setting
Color Level
Level Setting
Stibilize
On/Off
Dehumidification
Available
Defog
Low / Middle / Max
Environment
Operating Humidity
30 % ~ 90 % RH
Operating Temp.
- 40°C to 50°
-10°C to 40°
Electrical
Power Consumption
Max 16W
Max 12W
Power Supply
AC24V, 50/60Hz
Mechanical
Construction
Aluminum body
PC body
Clear vandal bubble (PC)
Dimension
168mm(Diameter) x
175.6(Height) mm
104mm(Diameter) x
138(Height) mm
Weight
About 3.3kg
About 0.74kg
7. Specification
51
DISTRIBUTED BY
Loading...