D-MAX 27X, 33X, 37X User Manual

AUTO FOCUS, DAY&NIGHT

ZOOM COLOR CAMERA

USER MANUAL

사용 설명서

용 서

27X / 33X / 37X

Contents

1. Precautions 3

2. Features 4

3. Products Components 5

4. Name and Functions of Each Parts 6

1) Front

2) Back

5. Connection 9

1) Connecting to Monitor

2) Connecting to Connection

6. Operating Your Camera 11

1) Menu Configuration

2) Menu Setup

7. Trouble Shooting 35

8. Specifications 36

2

1. Precautions

Cautions

This information is provided to ensure your safety and to prevent any loss, financial,

Please read it carefully and use the products accordingly.

- Warning -

Installation of this product by unqualified personnel is strictly prohibited, Please
consult an experienced installer or authorized retailer for proper installation to avoid
possible fire or electric shock.

If the camera overheats or smoke is noticed, turn off immediately. It may cause
fire

Do not install the product in an area of high humidity or near flammable materials
(e.g oil or gas)
Install the product in an incorrect environment may cause fire, electric shock
damage to the product

Do not install correct installation place, to prevent possible fall to product.

Do not handle power plug with wet hand, it might cause electric shock.

Do not insert foreign objects into the product or disassemble the products. It may
cause ire or damage the product.

- Cautions -

Use only under temperature condition (+50°C~-10°C).

Severe light changes or flickering may hinder normal camera operation.

Fall or strong shock, it may cause malfunction.

Do not exposure direct sunshine or strong light the camera.

Avoid touching the camera lens with finger.

3

2. Features

High Magnification Zoom Lens
High 432 x zoom function. (x27 Optical zoom, x16 Digital zoom)
High 528 x zoom function. (x33 Optical zoom, x16 Digital zoom)
High 592 x zoom function. (x37 Optical zoom, x16 Digital zoom)

High resolution 600TVL
Color : more than 600TVL, B/W : more than 700 TVL.

SSNR3 Function
Low illumination noise has been significantly reduced and resulting in a clear and sharp
image display in the dark.

Low illumination, Day Night
The camera automatically determines whether it is night time or day time, selecting
operating mode automatically.
Change B/W mode (0.02Lux) building in ICR DAY & NIGHT in the dark.

DIS Function
Compensate for vibration of camera under the shaking condition.

Motion detection
Once motion is detected, the camera sends an alert signal to the processing unit without
separate sensor (Output MD of External signal)

Miscellaneous Functions
Preset, Privacy Zone Masking, Digital zoom. Image Pause, Mirror Effect, Up Down

reversion etc.

Control via OSD menu and RS-485
The OSD menu and RS-485 pins allow for remote control for the camera, the user can
control the lens using external control connection.

Multi Protocol
Various Protocols available by using Multi Protocol function.

4

3. Products Components

구성물

1. Color zoom camera

2. Instruction Manual

5

4. Name and Functions of Each Part

1) Front

①Tripod Mounting Bracket Screw Hole

Used to fix tripod mounting bracket on top of the

camera.

Tripod mounting is attached on bottom of the

camera but it can install the mounting in the top of

camera when the user need.

* The measurement of suitable screw for the

holes→

②Remote receive

Zoom and focus functions can be controlled by using external controllers

☞ This function is optional

6

2) BACK

① Key Buttons

▪ UP (TELE button): To move the arrow indicator to up

- To close in on a far object. (ZOOM IN)

▪ DOWN (WIDE button): To move the arrow indicator to down

- To widen the view. (ZOOM OUT)

▪ SET: To access the main setup menu.

▪ LEFT (F-NEAR button): To move the arrow indicator to left

- To see a near object clearly

▪ RIGHT (F-FAR button): To move the arrow indicator to right

- To see a far object clearly

▪ AF button: To activate auto focus just once
② Power Input Terminal

- Power supply terminal (DC12V±10%).

7

☞ Notes

• If the Adaptor Power Line is extended improperly, it may cause malfunctions since the

camera is affected by unstable voltage condition.

• Ensure Power Supply Source: DC 12V ± 10%, 500㎃

• The wire is polarized. Match “+” and “-“terminals properly

③ Video Output Jack

- Used to connect an external video monitor in jack.
④ External Control Connector

- Zoom and focus functions can be controlled by using external signal, RS-485

communication.

⑤ Power LED

- Illuminates when power is supplied.
⑥ Tripod Mount Pole

- Used to install the camera on an optional Tripod or Bracket.

8

5. Connection

1) Connecting to Monitor

Connect Video Out Jack to the monitor's Video In jack as shown below.

• Connect cables with the unit powered down.

2) Connecting to connection

▪ External Control Connector

9

Focus and Zoom functions can be controlled by using external signals.

* It can be broken by using Overvoltage.

* MD (Motion Detection) Output Signal Level (less than 10mA)

▪ Communication Control Connector

10

6. Operating Your Camera

1) Menu Configuration

MAIN SETUP MENU

SSNR ▪ OFF ▪ ON

WHITE BALANCE ▪ ATW ▪ MANUAL ▪ AWC → SET

▪ OUTDOOR ▪ INDOOR

BACKLIGHT ▪ OFF ▪ BLC ▪ HLC

MOTION DET ▪ OFF ▪ ON

FOCUS ▪ MODE ▪ ZOOM TRK ▪ ZOOM SPEED ▪ D-ZOOM

▪ ZOOM POS INIT ▪ USER PRESET ▪ LENS INIT ▪ RET

EXPOSURE ▪ BRIGHTNESS ▪ IRIS ▪ SHUTTER ▪ AGC

▪ SSNR3 ▪ SENS-UP ▪ END

SPECIAL ▪ PRIVACY ▪ DAY / NIGHT ▪ DIS ▪ SYNC

▪ COMM ADJ ▪ IMAGE ADJ ▪ MONITOR ▪ DISPLAY ▪ RET

RESET

EXIT

2) Menu Setup

Use the six buttons on back of the camera.

11

1. Press the SET button for 2 seconds to access the main setup mode.

• Main setup menu is displayed on the monitor screen.

MAIN SETUP

SSDR ON ↙

WHITE BAL ATW

BACKLIGHT OFF

MOTION DET OFF

FOCUS ↙

EXPOSURE ↙

SPECIAL ↙

RESET

2. Select the desired feature by using the UP or DOWN button.

Select feature by using

MAIN SETUP

SSDR ON ↙

The UP or DOWN

WHITE BAL ATW

button.

BACKLIGHT OFF

MOTION DET OFF

FOCUS ↙

EXPOSURE ↙

SPECIAL ↙

RESET

EXIT

Change the status

by using the LEFT or

RIGHT button.

3. Change the status of the selected feature by using the LEFT or RIGHT button.

4. When completed, move the arrow indicator to 'EXIT' and press the SET button.

☞ Notes

• Features marked with a ‘↙’ have an accessible submenu.

• Some features marked with a ‘---‘ are not available according to the status of setting

option.

12

SSDR(Super Dynamic Range)

SSDR illuminates darker spots of an image while retaining the same light level for brighter

spots to even out the overall brightness of images with high contrast between bright and

dark spots.

1. When the SETUP menu screen is displayed, select ‘SSDR’ by using the button so that

the arrow indicates ‘SSDR’.

2. Use the button to change the SSDR level according to the contrast between bright and

dark areas.

MAIN SETUP

SSDR ON ↙

WHITE BAL ATW

BACKLIGHT OFF

MOTION DET OFF

FOCUS ↙

EXPOSURE ↙

SPECIAL ↙

RESET

EXIT

WHITE BAL

Your camera provides three 'WHITE BAL' control modes for your choosing in adjusting the

white balance.

1. Press the SET button to access the main setup menu and move the indicator to 'WHITE

BAL' using the UP or DOWN button.

2. Set 'WHITE BAL' using the LEFT or RIGHT button.

MAIN SETUP

SSDR ON ↙

WHITE BAL ATW

BACKLIGHT OFF

MOTION DET OFF

FOCUS ↙

EXPOSURE ↙

SPECIAL ↙

RESET

EXIT

13

※ The five white balance control modes are as follows.
▶ ATW (Auto Tracking White Balance):

Select This when the color temperature is between 1800°K and 10500°K

▶ AWC→SET (Auto White balance Control):

To find the optimal setting for the current luminance environment in this mode, set the

point the camera towards a sheet of white paper and press the SET button. If the

environment changes, readjust it.

▶ OUTDOOR:

Select this when the color temperature is between 1800°K and 10500°K. (sodium light

inclusion)

▶ INDOOR:

Select this when the color temperature is between 4500°K and 8500°K.
▶ Manual:

To fine adjust, select the Manual mode. You can increase or decrease the red or blue

factor while monitoring the difference on the screen. Set to 'MANUAL'mode and press

the SET button. Increase or decrease the value for red(R-Gain) and blue(B-Gain),

watching the color of the picture, and press the SET button when you obtain the best

color.

WHITE BAL MANUAL SETUP

▶ RED 117 |||||||||||||||

BLUE 93 |||||||||||||||

END

Press SET to return

☞ Notes

• Proper White Balance may not be obtained under the following conditions.

① When the scene contains mostly high color temperature object, such as a blue

sky or sunset.

② When the scene is dim.
③ If your camera directly faces a fluorescent lamp or is used in an environment of

varying lighting conditions.

14

BACKLIGHT

When there is a strong backlight behind the object, clear images of the

Background as well as the object can still be obtained by using the

BACKLIGHT function.

MAIN SETUP

SSDR ON ↙

WHITE BAL ATW

BACKLIGHT OFF

MOTION DET OFF

FOCUS ↙

EXPOSURE ↙

SPECIAL ↙

RESET

EXIT

1. Please position the arrow to point to 'BACKLIGHT' on the SETUP menu by using the UP

and DOWN buttons.

2. Please select the mode you wish to operate by pressing the LEFT or RIGHT button.

▶ BLC: Enables a user to directly select a desired area from a picture, and to view the

area more clearly.

▶ HLC (High Light Compensation) : If the scene contains extremely bright light areas

such as, from car headlight, the light can mask out much of the on-screen detail.

▶ OFF: Deactivates the BACKLIGHT function.

3. Select a desired mode using the Left and Right button and press the SET button.

z Select ‘BLC’ to adjust the area to be enhanced and

15

Enhancement level.

z Select ‘HLC’ to adjust the HLC MASK TONE and LEVEL.

☞ Notes

z Since the following symptoms may occur according to the ambient illumination when BLC is

selected, set it to OFF.

1 Color or screen changes unnaturally.

○

2 Noise appears in the bright part of the screen.

○

z Since the performance of the BLC function may be affected by the area of the bright part of the

screen, optimize the installation angle for the best BLC performance.

z If you increase LIMIT, the screen display may be distorted.
z For high performance of BLC func tion, We recommend that you set IRIS to AUTO in the EXPOSURE

setup.

z Activating BLC may cause the camera to repeat the Auto Focus operation depending on lighting

conditions. It is recommended that you use Focus Setup menu in One-Push or manual mode.

z Smart Zoom and BLC cannot be used in conjunction with each other.
z Setting up BLC and then Smart Zoom automatically cancels BLC.
z Setting up Smart Zoom and then BLC automatically cancels Smart Zoom.

MOTION DET.

This product has a feature that allows you to observe movements of objects in 8 different

areas on the screen, and the words ‘MOTION DETECTED’ appear on the screen when

movement is detected; hence a single individual can conduct supervision efficiently. The

camera detects an object’s movement by sensing disparity of outline, and level of

brightness and color. The camera receives detection signal from MD output terminal.

1. Please position the arrow to point to ‘MOTION DET’ on the SETUP menu. Using the UP
and DOWN buttons.

16

2. Please select the mode you wish to operate by pressing the LEFT or RIGHT button.

MAIN SETUP

SSDR ON ↙

WHITE BAL ATW

BACKLIGHT OFF

MOTION DET OFF

FOCUS ↙

EXPOSURE ↙

SPECIAL ↙

RESET

EXIT

① Please press the SETUP button.

- OFF : MOTION DETECTION mode is cancelled.

- ON : Any motion in the selected areas is observed.

▶ AREA SEL : Select the area user wants to observe in the 8 areas
▶ AREA MODE : Select to appear the word “ MOTION DETECTED” on the screen.
▶ SENSITIVITY: You can select up to 8 MD areas.

When SENSITIVITY number is high, motion detection sensitivity is increased to recognize
even small movement.

▶ SMART ZOOM : Smart Zoom is operated in connection with MOTION DETECTION.

When the SMART ZOOM function is ‘ON’ while the MOTION DETECTION mode is ‘ON’,
the zoom goes to the TARGET ZOOM position once motion is detected. Once the zoom
action is finished and ‘DWELL TIME’ has passed the zoom to the ‘START ZOOM’
position.

17

• START ZOOM : Use the left or right button in the ‘START ZOOM’ item to select the zoom

position from 1x to 27x (or 33x) to be returned after the ‘SMART ZOOM’ action is over.

• TARGET ZOOM : Use the left or right button in the ’TARGET ZOOM’ item to select the

zoom position from 1x to 27x (or 33x) to be used during motion detection.

• DWELL TIME : Use the left or right button in the ‘DWELL TIME’ item to select a time

between 5 and 60 seconds for the dwell time before the zoom is returned to the ‘START
ZOOM’ position. (5, 7, 10, 15, 20, 30, 40, 60 sec)

• TOP, BOTTOM, LEFT, RIGHT buttons : You can adjust the size of the area.

☞ Notes

Tips on Using the Motion Detection Feature

• The feature may not function properly under flickering light conditions.

• The camera interprets sudden changes in lighting and subsequent change in brightness
of an object as motion.

• With the feature enabled, other algorithms may require additional time to operatethan
usual.

• This system does not guarantee prevention of fire or theft. The manufacturer shall not be
held responsible for any accident or damage incurred.

• Connect an external alarm device to MD Out on back of the camera.

• Be careful of that MD Out can be appeared according to the moving of zoom.

FOCUS

MAIN SETUP

SSDR ON ↙

WHITE BAL ATW

BACKLIGHT OFF

MOTION DET OFF

FOCUS ↙

EXPOSURE ↙

SPECIAL ↙

RESET

EXIT

1. Press the SET button to access the main setup manu and then position the indicator

over FOCUS using the UP or DOWN button.

2. Press the SET button.

▶ MODE : You can select the most suitable zoom mode. Move the arrow indicator to
‘MODE’ by using UP or DOWN button. Digital zoom is operated after optical zoom (x27,
x33, x37) is finished.

18

• ONE PUSH :

Focus is automatically adjusted just once, after
zoom position is changed. Select 'ONE PUSH'
and press the SET button to confirm. Increase or
decrease optical zoom (ZOOM) or digital zoom
(D-ZOOM) positions by using the directional
buttons while verifying the changes on screen.
Press the SET button once desired image quality
is obtained.

• AUTO :

Select AUTO and press the SET button to
confirm. Increase or decrease optical zoom
(ZOOM) or digital zoom (D-ZOOM) positions by
using the UP or DOWN button while verifying the
changes on screen. Enabling D-ZOOM (ON)
means that digital zoom will activate once optical
zoom ends. Focus is automatically adjusted with
moving zoom.

• MANUAL :
Select 'MANUAL' and press the SET button to
confirm. Increase or decrease optical zoom
(ZOOM) or digital zoom (D-ZOOM) positions by
using the directional buttons while verifying the

changes on screen. Press the SET button once

desired image quality is obtained. Focus can be
manually adjusted, independent of moving zoom.

▶ ZOOM TRACK: Select ‘ON’ for the ‘SMART ZOOM’ item in the motion detection menu
and press SET button to change the settings for the ‘SMART ZOOM’ funtion.
Use the left or right button in the ‘ZOOM’ item to select ‘AUTOTRACK’ or ‘TRACK’ and
press SET button to activate the zoom action focus function.

19

• AUTOTRACK: Zooming in while deciding or adjusting the status of the focus.

• TRACK: Zooming in with no relevance to the focus.

• OFF: Only the zoom lens moves.

▶ ZOOM SPEED : Configure zoom tracing speed by using this feature. Position the

indicator over 'ZOOM SPEED' by using the UP or DOWN button and
then set todesired mode by using the LEFT or RIGHT button.

z FAST : To move zoom fast.
z MEDIUM : To move zoom at medium speed.
z SLOW : To move zoom slowly.

☞ Notes

z The ‘ZOOM SPEED’ mode cannot be used if ‘MODE’ is set to ‘AUTO’ and ‘ZOOM

TRAKck’ is ‘ON’.

▶ D-ZOOM : Configure magnification limit from x2~x16 using this feature. Position the

indicator over 'D-ZOOM' by using the UP or DOWN button. Set 'D­ZOOM' to'ON' and press the SET button to confirm.

z Set ‘ZOOM LIMIT’ to the desired level Using the LEFT or RIGHT button.

20

☞ Notes
When the DIS is enabled, you cannot use the D-ZOOM.

▶ ZOOM POS INIT : Moves to the controlled ZOOM position when the power truned on

and is a function of the initial ZOOM position control.

z AUTO : If you turn the power off and on, the zoom magnification level is set to the

previous level that was set before the power went off.

z MANUAL : The zoom magnification level can be set from 1x to 27x (or 33x, 37x).

☞ Notes

When the DIS is enabled, you cannot use the D-ZOOM and the zoom position is saved
after 5 seconds when you set zoom function.

▶ USER PRESET: Preset user-designated configurations using this feature.

Position the indicator over ‘USER PRESET’ using the UP or DOWN

button and then set to ‘ON’ using the LEFT or RIGHT button.

Press the SET button to confirm.

21

● PRESET NO : Up to 128 preset configurations are supported.

● PRESET SAVE : Save configured preset.

● PRESET CLEAR : Clear configured preset.

● END : Revert to the FOCUS SETUP menu.

LENS INIT :▶ Use the left or right button in the ‘Lens initialization’ item to select

‘Automatic’ or ‘Manual’ and press the SET button to set up the initialization of the lens.

• AUTO : The lens is initialized by setting the date. reset time can be set from 1 day to 7
days and the lens resets every 24 hours from the set time.

• Manual : The Lens will reset when you press the SET button.

▶ END : To revert to the main setup menu.

EXPOSURE

1. Press the SET button to access the main setup menu and then position the indicator

over 'EXPOSURE' by using the UP or DOWN button.

2. Press the SET button to confirm.

22

MAIN SETUP

SSDR ON ↙

WHITE BAL ATW

BACKLIGHT OFF

MOTION DET OFF

FOCUS ↙

EXPOSURE ↙

SPECIAL ↙

RESET

EXIT

▶ BRIGHTNESS : Use this feature to adjust image brightness. Position the indicator over

'BRIGHTNESS' using the UP or DOWN button. Then increase or

decrease brightness level by using the LEFT or RIGHT button while

verifying the changes on screen. Set END once desired level is

obtained.

▶ IRIS : Set 'IRIS' to 'AUTO' or 'MANUAL'. Position the indicator over 'IRIS' by using

the UP or DOWN button and then select the desired iris mode using the LEFT

or RIGHT button.

23

• AUTO: The iris is automatically activated upon illumination.

• MANUAL: Manual iris configuration. Set 'IRIS' to 'MANUAL' by using the LEFT or

RIGHT button and then press the SET button. Increase or decrease iris level by

using the LEFT or RIGHT button while verifying the changes on screen.

▶ SHUTTER : Control image brightness by adjusting shutter speed.

① Position the indicator over 'SHUTTER' by using the UP or DOWN button. Then

select the desired shutter mode (A.FLK, ESC, MANUAL) using the LEFT or RIGHT

button.

24

• A.FLK (NTSC: 1/100, PAL: 1/120): Flicker-free mode.

• ESC : Automatic shutter speed setting (optimal). Auto operation is possible only when

the IRIS is set to MANUAL.

• MANUAL : Manual shutter speed setting.

② If you choose ‘MANUAL’, select the optimal shutter speed.

· In MANUAL mode, the optimal shutter speed needs to be designated.

Select from 1/60 to 1/120,000 (NTSC) or from 1/50 to 1/120,000 (PAL).

* 'Sens-Up' mode can be configured manually (2x to 512x).

· Verify changes made to the shutter speed by referencing to changes in on screen

brightness.

③ Press the SET button to complete.

☞ Notes

• Image may become unstable if the camera is set to 'ESC' mode and faces a strong

fluorescent light.

• Under 'ESC' mode, the brightness can be adjusted using the LEFT or RIGHT button.

• Sens-up is disabled under 'MANUAL' or 'A.FLK' mode.

▶ AGC (Auto Gain Control) : For brighter images.
① Position the indicator over 'AGC' by using the UP or DOWN button.
② Set 'AGC' to the desired mode by using the LEFT or RIGHT button.

• HIGH : Wide range gain value adjustment

25

• MEDIUM : MEDIUM range gain value adjustment

• LOW : Narrow range gain value adjustment

• MANUAL : Selecting gain value range.(5dB~41dB)

• OFF : Disabled

▶ SSNR3 : On screen noise reduction.

① Position the indicator over 'SSNR' by using the UP or DOWN button.
② Set 'SSNR' to the desired mode by using the LEFT or RIGHT button

• OFF : Disabled.

• LOW : Low noise reduction.

• MEDIUM : MEDIUM noise reduction.

• HIGH : High noise reduction.

☞ Notes

• Changing 'AGC' setting from LOW to HIGH results in greater sensitivity, as well as on

screen noise.

26

• SSNR function is disabled in AGC mode ‘OFF’.

▶ Sens-UP: This feature ensures clear images at night or under low lighting conditions.

① Position the indicator over 'SENS-UP' using the UP or DOWN button.
② Set 'SENS-UP' to the desired mode using the LEFT or RIGHT button.
③ Select SET button is AUTO mode then, SENS-UP limit can be adjusted from

x2~ x512.

• AUTO: Select this mode for use in night time or under low lighting conditions.

• OFF: Disabled

☞ Notes

• SENS-UP doesn’t work when AGC mode off.

• SENS-UP doesn’t work when SHUTTER is Manual

• Enabling Zoom magnification increase, the image is brighter but it may result image

ghost of moving subject and Auto focus b properly.

▶ END : Save the exist setting and move the Main Setup Menu.

27

SPECIAL

1. Press the SET button to access the main setup menu and then position the indicator

over 'SPECIAL' using the UP or DOWN button.

2. Press the SET button to confirm.

SPECIAL SETUP

PRIVACY OFF

DAY/NIGHT AUTO↙

DIS OFF

SYNC INT

COMM ADJ ↙

IMAGE ADJ ↙

MONITOR CRT↙

DISPLAY

RETURN

▶ PRIVACY: Mask privacy area by using this feature. The mask area expand/contract

upon the zoom position.

① When the SPECIAL menu screen is displayed, press the Up and Down buttons so

that the arrow indicates ‘PRIVACY’.

② Set up the mode using the 4 direction buttons.

• AREA SEL

Configure eight mask areas.

28

• AREA MODE

Mask area display.

- TOP : To move the mask area up.

- BOTTOM : To move the mask area down.

- LEFT : To move the mask area left.

- RIGHT : To move the mask area right.

• MASK COLOR

Adjust desired mask color level.

• MASK TONE

Adjust desired mask transparency level.

• END

Select this to save the PRIVACY menu settings and return to the SPECIAL menu.

▶ DAY & NIGHT : Select from COLOR, BW or AUTO modes.
① When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Up and

Down buttons so that the arrow indicates ‘DAY/NIGHT’.
② Select a desired mode using the Left and Right buttons according to the picture

display you want.

• COLOR: Color mode.

• B/W: BW mode.

•AUTO: The camera automatically detects lighting conditions and selects the mode

accordingly.

•DWELL TIME : You can select the duration time about

changing the day/night mode.

→ 5,7,10,15,20,30,40, 60(sec)

•DURATION : You can select brightness of illumination

about changing the day/night mode.

• EXT : This mode allows you to apply a desired filter to external signals.

29

☞

Notes

• When “AGC” is set to “OFF”, AUTO MODE cannot be used but, only use “COLOR

MODE” and “B/W MODE”.

• When Use B/W mode under Sunlight or Halogen Lamp, the focus may be smear than

normal light.

DIS : ▶ The DIS mode can compensate for vibration of the camera.

☞ Notes

• When DIS is operating, D-ZOOM does not operate.

SYNC : ▶ Apply INIT mode.

• INIT : Internal synchronization

COMM▶ ADJ : Use this feature to select communication protocol. Position the indicator

over 'COMMUNICATION' by using the UP or DOWN button.

• PROTOCOL : Select the communication PROTOCOL.

(D-max/STW/PELCO-D/PELCO-P)

• CAM ID : Assign an ID number to the camera (1 to 255). Identification number zero is

used for Remote controller setup.

• BAUD RATE : Configure baud rate from

2400/4800/9600/19200/38400/57600/115200

bps.

• UART MODE : Configure parity bit to NON,

EVEN, or ODD. Data bit is set to 8bit, and stop

bit to 1bit. Set the UART MODE to EVEN if using

the Remote Controller.

•TERMINATION : Function that sets the

resistance at the end of RS-485 communications.

• PET PKT : Used to transfer a packet.

☞

Notes

• It can be setup any item in the COMMUNICATION SETUP by RS-485 interface except

for moving, exit of the menu. To be complete setup the items or parameter values, please

use key buttons on the rear panel of this camera or a remocon controller.

30

IMAGE ADJ :▶ Includes image quality or special function factors.

○1 When the SETUP menu screen is displayed, select ‘IMAGE ADJ’ by using the Up and

Down buttons so that the arrow indicates ‘IMAGE ADJ’.

○2 Selected a desired mode using the Up and Down buttons.

• H-REV : Use this feature to horizontally inverse the screen.

• V-REV : Use this feature to vertically inverse

the screen.

• SHARPNESS : Increasing this value

sharpens object edges. Too high of a setting,

however, produces noise and may obscure the

image.

• COLOR : Adjusting this value affects the

chroma level only; the burst level is unaffected.

• END : Return to the USER PRESET menu.

MONITOR▶

Please change the settings value of video appropriate to your monitor.

LCD : Please select this menu item when using an LCD monitor

- CRT : Please select this menu item when using a CRT MONITOR

- USER : Please use this menu item when using a monitor other

than standard ones. You can change the gamma, PED level, and

color gain in the sub menus.

31

DISPLAY:▶ Includes image quality or special function factors.

• CAM TITLE : Use this feature to designate

a name for the camera, which will display on

the monitor screen.
①Press the SET button to display the main

setup menu and move the arrow indicator to

'CAM TITLE' by using the UP or DOWN button.
②Set 'CAM TITLE' to 'ON' by using the LEFT

or RIGHT button.

☞

Notes

• If the CAM TITLE feature is set to 'OFF', the name will not displayed in the monitor.

③Press SET button.
④You can enter up to 20 characters.

a. Move the cursor to the character entry

field by using the LEFT or RIGHT button.

b. Use UP, DOWN, LEFT, and RIGHT

buttons to select a desired character.

c. Press the SET button to confirm selection

of the blinking character. The character is then

saved, and the cursor in the entry field moves

to thenext position.

d. Repeat steps ‘a’ through until the desired

name has been entered.

☞

Notes

• Correcting Mistakes

- Move the cursor to 'CLR' and press the SET button to clear the entire entry. To

modify one character, use ‘←’ or ‘→’to position the cursor above the characterto be

modified and click the SET button after selecting the character to enter.

32

⑤Select on screen position of the CAM TITLE.

a. Move the cursor to 'POS' and press SET button.

b. The CAM TITLE is displayed on the top-left of the monitor screen. (Default position)

c. Select the position by using the 4-directional buttons, then press the SET button to

confirm the position.

⑥When completed, move the cursor to 'END' and press SET button.

• CAM ID : Displays camera ID on top left corner of the screen.

• CAM INFO : Displays camera information on screen.

• MOTION ALARM : You can toggle the use of the camera alarm.

• ZOOM MAG : Use th is feature to display the current zoom magnification level on screen.

Position the indicator over ‘ZOOM MAG’ using the UP or Down button. Then set to ON
using the LEFT or RIGHT button.

33

• LANGUAGE : You ca n select the menu language according to your requirements
(ENGLISH, Chinese, DEUTSCH, ITALIANO, FRANCAIS, ESPANOL, Korean, Japanese,
PORTUGUESE )

• END : Select this to save the DISPLAY menu settings and return to the SPECIAL menu.

RESET

To reset your camera to factory default condition.

☞

Notes

• Some in ‘COMM ADJ’ mode can not be reverted even if it is RESET.

EXIT

To finish setup menu.

34

7. Troubleshooting

Problem Solution

No display • Check the power cable and the wiring between the camera and

the monitor.

• Ensure proper video cable connection (Video Out Jack).

Dim display • The lens could be dirty. Clean with a soft, clean piece of cloth.

• Adjust monitor settings.

• Adjust camera position if exposed to a strong light source.

Dark display • Adjust the monitor's contrast level.

• Set the intermediate device, if in use, to 75Ω/ Hi-z

The camera is not functioning properly

and its surface is hot.

Auto mode of DAY/NIGHT is not

selected or not active.

Motion Detection feature is not active. • Ensure that the feature is set to ON

Improper color • Check the “WHITE BAL” mode, the setting is properly.

Uneven colors Flickering • Adjust and configure WHITE BAL

SENS-UP feature is not active. • Ensure AGC menu is set to ON.

• Check the power source for compliance with specifications

• Ensure DAY/NIGHT mode, the mode set to “AUTO”

• Ensure AGC mode is set to “ ON”

• The camera may be facing the sun or a fluorescent light. Adjust

the position of the camera.

• Ensure SHUTTER MENU is set to MANUAL.

35

8. Specifications

Signal system NTSC PAL
Image Sensor 1/4” Sony super HAD CCD

Total Pixels 811(H)X508(V) 795(H)X596(V)

Effective Pixels 768(H)X494(V) 752(H)X582(V)

Resolution Color : 600TV Lines(Min), B/W : 700TV Lines(Min)

Scanning Frequency 15.734KHz(H), 60(V) 15.625KHz(H), 50(V)

Scanning System 2:1 Interlace

525 Lines/60Fields/30Frames

Shutter Speed 1/60~1/120,000 sec 1/50~1/120,000 sec

Min. Illumination 0.4Lux @F1.6 (Normal Color Mode)

0.02Lux @F1.6 (B/W Mode)

0.00004Lux @F1.6 (Sens-up Mode)

Zoom Rate 27X, f3.5~94.5mm (F1.6~3.9)

33X, f3.5~111.5mm (F1.6~3.9)

37X, f3.5~129.5mm (F1.6~3.9)

Digital Zoom 16x

DIS ON / OFF

Min. Focus Distance 1.5m

Angle Field of view 27X, H: 55.5°(Wide)~2.24°(Tele), V:42.5°(Wide)~1.79°(Tele)

33X, H: 55.5°(Wide)~1.77°(Tele), V:42.5°(Wide)~1.33°(Tele)
37X, H: 55.5°(Wide)~1.59°(Tele), V:42.5°(Wide)~1.19°(Tele)

Back Light BLC / HLC / OFF

SSDR ON / OFF

Day & Night AUTO / COLOR / B/W

Privacy Zone On / Off (8 Areas)

AGC LOW / MEDIUM / HIGH / MANUAL / OFF

Camera ID On ( 255 ID Selectable ) / Off

White Balance ATW / Manual / AWC→SET / OUTDOOR/ INDOOR

SSNR LOW / MEDIUM / HIGH / OFF

OSD Built-in

Flip / Mirror On / Off

Communication RS 485, Multi Protocol (D-max, STW, Pelco)

S/N Ratio 52dB (AGC Off)

Video Output Composite video output 75 ohm terminated

Sync. System Internal

Operating Humidity 30 % ~ 90 % RH

Operating Temp. - 10°C to 50°C

Dimension 60(W) X 64(H) X 119.8(D)mm

Weight About 378g

Power Consumption Max 5.1W

Power Supply DC 12V (±10%) 500㎃

625 Lines/50Fields/25Frames

2:1 Interlace

36

37