Page 1
ULTIMATE SERIES
SUBWOOFERS
WELCOME
Thank you for buying a DLS ULTIMATE subwoofer.
The subwoofer must be installed correctly in order to work well.
This manual will show you how to install it like a pro. Please
read the entire manual before beginning the installation.
Install the subwoofer yourself if you feel confident with our
instructions and if you have the proper tools. However if you
feel unsure, turn over the installation job to someone better suited
to it. The speakers are designed for enclosure mounting.
CONNECTION OF SUBWOOFER
How to connect depends on what type of amplifier you use.
The best is to follow the instructions given in the manual for the
amplifier. Most amplifiers today have built-in lowpass crossover
and possibilities to connect your subwoofer in bridge mode.
Two 4 ohm subwoofers are often connected in stereo mode
since most amplifiers can´t handle bridge mode loads below 4
ohms.
SP12i and 15 have dual, two ohm, voice coils which should be
considered when you connect them.
SP15S has four 2 ohm voice coils that can be connected in
many different ways.
We also recommend the use of a subsonic highpass filter. This
gives a better bass reproduction with less "rumble". In most
DLS amplifiers this feature is already built-in.
For wiring use high class speaker wires, min AWG11 (4 mm
2
).
SP12i, SP15
SP15S, SP18S
SUBWOOFER ENCLOSURES, GENERAL
Build your enclosure in a stable and airtight material. The best
is MDF-board, 19 mm, or particle board, 22 mm. Larger
enclosures must have bracing inside to avoid vibrations. The
enclosure must be completely airtight. Use sealing compound
in all joints, also around the cable terminals. The size of the
enclosure is decided by the speaker data.
SEALED ENCLOSURES
Sealed enclosures are easy to build. The size is not critical, but
it can´t be too small. The speaker data such as Fs, Qts, Vas
and X-max decides the size of the enclosure.
Large speakers need larger boxes. Two speakers need a box
of the double size etc. The enclosure must be completely airtight.
A sealed enclosure should be filled with acoustic wool up to 75
- 100%.
A sealed enclosure has a lower efficiency than vented
enclosures but they can handle high power and are easy to
build.
A subwoofer in a sealed enclosure creates a tight bass suit able
for the audiophiles listening to classical music, jazz and soft
rock.
VENTED ENCLOSURES
A speaker in a vented enclosure has a higher efficiency (3 dB)
and higher power handling capacity than in a sealed enclosure.
In a vented enclosure the sound from the speaker and the port
work together creating a higher sound level. The sound from
the port must come out in the same phase as from the speaker
otherwise the result is bad.
The size of the vented enclosure is decided by the speaker
data just as for the sealed one.
The size of the vehicle often decides the practical size of the
enclosure. A smaller enclosure has a higher resonant frequency
than the larger one. The size of the enclosure should not be so
big that the speaker plays below it´s own free air resonance
(Fs), then it looses in power handling capacity.
The port does not have to be fully inside the enclosure as long
as the area and length are correct. Sometimes you need two or
more ports in an enclosure. You can convert from one to two or
more ports as long as the total port area is the same.
All DLS subwoofers works well in vented enclosures.
BANDP ASS ENCLOSURES
In all bandpass enclosures the speakers are hidden inside the
enclosure, all sound is coming out through the ports. There are
different types of bandpass enclosures and they have in common that they are a bit more difficult to build. Most DLS
subwoofers can be used in bandpass enclosures.
IMPORTANT!
Think of the speaker weight when you mount it. If you don´t
mount it properly it can come loose.
Valid from 2010-01-13
DLS Svenska AB
P.O. Box 13029
SE-40251 Göteborg, Sweden
Tel: +46 31 840060
Fax: +46 31 844021
E-mail: info@dls.se
www.dls.se
Technical Assist ance
For technical assistance ask the shop where the product was
sold or the distributor in your very country.You can always phone
the DLS Helpdesk in Sweden + 46 31 840060 or send an email to info@dls.e
Information can also be found on our WEB-site www.dls.se
We follow a policy of continuous advancement in development.
For this reason all or part of specifications & designs may be
changed without prior notice.
WARRANTY SERVICE
This speaker is covered by warranty, depending on the
conditions in the country where it is sold. If the speaker is returned for service, please include the original dated receipt with
the product.
upper
suspension
voice coil
pole plate
magnet
spider
chassis
dust cap
speaker cone
T-yoke
THE SUBWOOFER
Page 2
TECHNICAL SPECIFICATIONS FOR DLS ULTIMATE SUBWOOFERS
SP12 SP15 SP15S SP18S
Size 30 cm (12") 37,5 cm (15") 37,5 cm (15”) 45 cm (18”)
Impedance 2 x 2 ohm 2 x 2 ohm 4 x 2 ohm 3 x 2 ohm
Nom. power (RMS) 500 W (max 800) 500 W (max 800) 500 W (max 800 ) 500 W (max 800 )
Maxiumum power for SPL use 1200 W 1200 W 2000 W 2000 W
Freq. range 20 Hz- 2 kHz 15 Hz-2 kHz 15 Hz - 1 kHz 13 Hz - 1 kHz
Sensitivity 97,3 dB 99,9 db 88,2 dB 90,5 dB
Voice coil diameter 75 mm (3”) 75 mm (3”) 75 mm (3”) 100 mm (4”)
Voice coil height 32 mm (1,26”) 32 mm (1,26”) 28 mm (1,1”) 32 mm (1,1”)
Re 1,27 ohm* 1,25 ohm* 1,8 ohm** 2,2 ohm**
Voice coil inductance, 1 kHz 0,52 mH 0,57 mH 0,68 mH 1,16 mH
BL product 8,73* 8,49* 11,47** 12,07**
X-max +-12 mm (0,47”) +-12 mm (0,47”) +-12 mm (0,47”) +-12 mm (0,47”)
Suspension compliance CMS 344 240 925 936
SD- Effective piston area 452,3 cm
2
754,8 cm
2
855 cm
2
Resonant freq. (Fs) 30,5 Hz 33,2 Hz 32 Hz 31,9 Hz
Vas (liters) 98,76 191,7 94,4 177
Vas (ft3) 3,48 6,77 3,33 6,25
Qms 4,42* 4,22* 3,97** 5,33**
Qes 0,25* 0,35* 0,74** 0,8**
Qts 0,24* 0,32* 0,62** 0,7**
Cone material Paper Paper Paper Paper
Magnet weight 200 oz (5,67 kg) 200 oz (5,67 kg) 200 oz (5,67 kg) 200 oz (5,67 kg)
Magnet diameter 8,7" (220 mm) 8,7" (220 mm) 8,7" (220 mm) 8,7" (220 mm)
Installation depth 5,71" (145mm) 6,89" (175 mm) 6,89" (175 mm) 8,66” (220 mm)
Mounting hole 11,22" (285 mm) 14,17" (360 mm) 14,17" (360 mm) 16,9” (430 mm)
Outer diameter 12,4" (315 mm) 15,35" (390 mm) 15,35" (390 mm) 18,3” (465 mm)
Weigth 28,66 lb (13 kg) 29,54 lb (13,4 kg) 29,54 lb (13,4 kg) 43,65 lb (19,8 kg)
* Data measured with VC connected in parallel ** Data measured on single voice coil
Single VC Two VC in parallel Four VC in parallel Two VC in series
Impedance 2 ohm 1 ohm 0,5 ohm 4 ohm
Sensitivity 88,2 dB 90,8 db 93,5 dB 90,4 dB
Re 1,8 ohm 0,9 ohm 0,45 ohm 3,8 ohm
Voice coil inductance, 1 kHz 0,68 mH 0,59 mH 0,57 mH
BL product 11,47 10,8 10,55 20,74
Suspension compliance CMS 0,0925 0,0925 0,0925 0,0955
SD- Effective piston area 855 cm
2
855 cm
2
855 cm
2
855 cm
2
Resonant freq. (Fs) 32 Hz 32 Hz 32 Hz 31,9 Hz
Vas (liters) 94,4 94,4 93,4 97,5
Vas (ft3) 3,33 3,33 3,3 3,44
Qms 3,97 4,14 4,45 2,87
Qes 0,74 0,41 0,22 0,46
Qts 0,62 0,37 0,21 0,4
TECHNICAL SPECIFICATIONS / TS PARAMETERS FOR SP15S IN VARIOUS
VOICE COIL CONFIGURATIONS
SEALED ENCLOSURE
SP15S: 40 liters, F3: 56 Hz
1,41 ft
3
(Use only one voice coil)
Single VC Four VC:s in parallel
SP15S: 54 liters, F3: 46 Hz
1 x 4” port, 26 cm long
1,9 ft
3
(Use all four voice coils in parallel)
ENCLOSURES FOR SP15S (for music, not SPL)
SP15S: 54 liters, F3: 46 Hz
1 x 4” port, 26 cm long
1,9 ft
3
(Use two voice coils in parallel)
Two VC:s in parallel or
two VC:s in series
VENTED ENCLOSURE
VENTED ENCLOSURE
Page 3
HINTS & TIPS FOR ”DO IT YOURSELF” ENCLOSURE BUILDERS
ABOUT THE RECOMMENDED
ENCLOSURES
The performance of these recommended enclosures will vay
from vehicle to vehicle. It is more difficult to get a tight and well
defined bass in a SEDAN vehicle because of the tightness
between trunk and interior of the vehicle. In this case a bandpass box could be a better choise.
- All volumes are inside measures.
- Volumes occupied by speaker and ports have already been
added to the given enclosure volumes.
- Use conical bass ports for best result. (DLS BP-75 or BP-
110). If the ports are too long for the box you can use a bend.
Either cut the tube and glue it together in angle, or use factory
made tube bends. It´s easier to use the factory made ones. The
total length must be the same as for a straight tube. Make the
measure in the center of the tube.
The port opening inside the enclosure must not be closer to an
interior wall than 3” (75 mm), otherwise it will have negative
effects on the airflow.
- The enclosure must be very steady and completely air-tight.
Use 22 mm particle board or 19 mm MDF-board. The particle
board has a self resonant frequency of 14 Hz while the MDF
has a resonant frequency of approx. 400 Hz. It´s important to
do some type of bracing inside the enclosure to avoid vibrations.
Volume taken up by bracing should be added to the enclosure
volumes.
ENCLOSURE DAMPING
Most enclosures should be damped inside with syntetic
(acoustic) wool or damping mat (line). Attach the damping material on the wall opposite from the speaker and port. A sealed
enclosure should be filled up to 70-100% with acoustic wool.
In a vented enclosure the speaker and port should be on the
same side, otherwise a fade-out of some frequencies can occour.
In most vehicles, except for SEDAN cars, the speaker and port
should be directed backwards for best result.
ENCLOSURE PLACING IN DIFFERENT
TYPES OF VEHICLES
In small vehicles like VW Golf, Peugeot 306 and similar the
bass box should be installed with both speaker and port directed
backwards. Alternatively booth speaker and port can be directed
upwards. This way of mounting is valid for all types of vehicles
where the trunk is incorporated with the inner compartment.
In sedan vehicles with the passenger compartment separated
from the trunk, the enclosure should be installed with booth
speaker and port directed towards the rear seat. Some cars
have an opening in the middle of the rear seat for loading skis
etc. Y ou can install the enclosure behind this opening and direct
speaker or port through this opening. There must be some free
space in front of the port, (between the rear seat and the port
opening).
In large vehicles like st ation wagons the best sound is achieved
with the enclosure installed behind the rear seat with booth speaker and port directed backwards. Alternatively you can install
the enclosure on one side of the luggage compartment.
CALCULA TE YOUR ENCLOSURE
Box volumes:
When caculating the volume of an enclosure you simply multiply
the width (W) x heigth (H) x depth (D).
Use measures in dm and you will get the answer in liters.
A trapezoid box is calulated as below:
Vol=width (W) x heigth (H) x upper depth (UD) + lower depth (LD)
2
Be sure to measure the
inside dimensions.
W
H
UD
LD
VENTED ENCLOSURES FOR SP121 & SP15
VENTED ENCLOSURE
Subwoofer Volume (liters/ft3) Port Damping F3 Fb
SP12 single VC vol: 41,9 / 1,48 4” x 35 cm/13,8” Line inside 38,1 Hz 38,6 Hz
SP12 par. VC vol: 36,9 / 1,30 3” x 25 cm/9,84” Line inside 30 Hz 32 Hz
SP12 ser. VC vol: 40,4 / 1,43 4” x 17 cm/6,7” Line inside 50 Hz 50 Hz
SP15 single VC vol: 60 / 2,12 2x4” x 35 cm/13,8” Line inside 53 Hz 45,0 Hz
SP15 ser. VC vol: 60,55 / 2,14 2x4” x 37 cm/14,5” Line inside 44,7 Hz 44,0 Hz
F3 = approximative lower frequency for vented
boxes in Hz. Often called F-3 dB point = the point
where the power is 50% lower.
Fb = Box resonant frequency
SEALED ENCLOSURE
SP15: 54,5 liters, F3: 67,5 Hz
1,92 ft
3
(Use only one voice coil)
SEALED ENCLOSURE FOR SP15SPL ENCLOSURES FOR SP12, 15, 15S, 18S
The enclosure examples can be used only for the reproduction
of normal music. If you want to use these subwoofers for SPL
competition, which they are designed for, the design of an
enclosure is more complicated.The vehicle must be modified
in many ways and the enclosure must be individually designed
for each vehicle type and also for the different competition
classes.
On our website www.dls.se you will find some helpful hints
(PDF document) regarding the build of SPL competition
vehicles.
RUNNING-IN PERIOD
Allow the speaker to play for at least 1520 hours. After this time the
performance is correct.
Loading...