Dls GOTHIA 1, NORDICA 1, UP1i INSTALLATION

DLS ULTIMATE

6

TWEETERS

UP1i
Gothia 1
Nordica 1

Welcome

Thank you for buying a DLS Ultimate tweeter.
This manual will show you how to do a correct installation. Please
read the entire manual before beginning the installation. Install
the speakers yourself if you feel confident with our instructions
and if you have the proper tools. The ULTIMATE speakers are
our best speaker line but a poor installation job can destroy the
final result even from these speakers. So if you feel unsure,
turn over the installation job to someone better suited to it.

Installation

The speakers should be installed high up in the door side or
on the dashboard. In competition vehicles they are often
installed in the A-pillar which is a very good installation spot to
achieve a good sound stage. This kind of mounting requires
more job. If you install them in the A-pillar, make sure they are
installed in a strong stable baffle, this will improve the sound
quality.
UP1C comes with mounting accessories for both recessed
and surface mount. Iridium1 and Nobelium 1 are intended for
use only in recessed mounting.

Wiring

Use high quality speaker cables like DLS HQS or similar.
Avoid using the factory pre-installed cabling, they will not give
the sound reproduction that you should expect from these
high class speakers.
Make sure the cables don’t get jammed causing a short circuit
to ground. This can damage the output circuits of your head
unit or amplifier.
Connect the cables with correct polarity to the speakers.

Break-in period

Allow the speakers to play at normal volume for at least 15-20
hours. After this time the performance is correct.

Technical data UP1i

Art.no 10-25301i
Size 28 mm
Nom. power (RMS) 50 Watts (80 Watts max)
Freq. range 1,5 kHz-20 kHz
Sensitivity 93 dB
Fs 1200 Hz
Overall dimensions 60 mm / 2,36"
Magnet 28 mm / 1,1" neodymium
Mounting depth 18 mm / 0,71"
Mounting hole 48 mm / 1,89"
Cone material Hand treated fabric

Technical data Gothia 1

Art.no 10-25201
Size 28 mm with chamber
Nom. power (RMS) 50 Watts (80 Watts max)
Freq. range 1 kHz-25 kHz
Sensitivity 93 dB
Fs 900 Hz
Overall dimensions 62 mm / 2,44"
Magnet 28 mm / 1,1" neodymium
Mounting depth 26 mm / 1"
Mounting hole 46 mm / 1,81"
Cone material Hand treated fabric

Technical data Nordica 1

Art.no 10-25901
Size 28 mm with chamber
Nom. power (RMS) 50 Watts (80 Watts max)
Freq. range 1 kHz-25 kHz
Sensitivity 93 dB
Fs 900 Hz
Overall dimensions 62 mm / 2,44"
Magnet 28 mm / 1,1" neodymium
Mounting depth 26 mm / 1"
Mounting hole 46 mm / 1,81"
Cone material Hand treated fabric

Technical Assistance

For technical assistance ask the shop where the product was
sold or the distributor in your country.
You can also send an e-mail to [e-mail]
Information can also be found on our web-site www.dls.se
We follow a policy of continuous advancement in development.
For this reason all or part of specifications & designs may be
changed without prior notice.

Warranty service

This speaker is covered by warranty, depending on the
conditions in the country where it is sold. If the speaker is retur­ned for service, please include the original dated receipt (or a
copy) with the product.

DLS Svenska AB

P.O. Box 13029

SE-40251 Göteborg, Sweden

Tel: [phone]

Fax: [phone]

E-mail: [e-mail]

www.dls.se

Crossover

The tweeters must be used with either a passive or an active
filter. When the tweeters are a part of a 2- or 3-way speaker
system, the filters are included, but if you buy them as separate
parts, you must use a separate high pass filter that limits the
lower frequency range. If the tweeters are connected without a
filter they will be destroyed.
A pair of cable filters are normally delivered with the tweeters,
but if you don’t have the filters you can build your own filter as
in the drawing below.
If the tweeter level is too high you can connect an extra resistor
in series with the + wire. Use a resistor 3,3 ohms, 5 Watts.

+

2,7 Ω

2345

-

0,4 mH
air coil

6,8 μF

Installation of Ultimate UP1i tweeter:

Surface mounting:

For angled surface mount use the angled cup (5):
The tweeter driver (1) is attached to the cup by fitting the three
wings on the angled cup into the tracks of the tweeter driver and
then turn it clockwise to lock. When removing the driver from the
cup, turn it ccw and lift it up. The cable goes through the hole in the
rear side of the cup. Attach to the surface with screws (6) or the
round adhesive tape cushions (7). A good place for installation is on
the dash board at the A-pillar directed towards a place between the
front seats.

Recessed mounting:

Drill a hole with a diameter of 48 mm / 1,89" in the door side.
The cup (2) is attached to the door side with the metal wing(3)
pressed to the back side of the door. Fasten the metal wing using
the two M3 screws (4).
Put the tweeter driver (1) into the cup with the cable going out
through the bottom hole. Then attach the driver into the cup and
turn it clockwise to lock in the cup. When removing the driver from
the cup, turn it ccw and lift it out.

5

1

2

6

3

7

4

Installation of Nordica 1 / Gothia 1 tweeter:

Recessed mounting 1:

You need a hole with a diameter of 46 mm / 1,88" in the door
side, fasten with four screws. A strong baffle will improve the
sound.

Recessed mounting 2:

Sometimes it´s necessary to install the tweeter at places where
you cant use the round flange. The flange (A) is possible to
remove from the tweeter driver (B) by turning it CCW.
If you prefer to install the tweeter with the flange attached to the
tweeter driver, we recommend you to add a string of strong glue
on the bottom side, between flange and chamber, to secure it.
This gives you the best sound reproduction in this installation.

B

A