Dixon 27 KOH-968999590, GRIZZLY 52, 27 KOH-968999588, 30 KOH-968999627, GRIZZLY 60 User Manual

GRIZZLY

™

ZTR

®

Operator’s Manual

GRIZZLY 52, 27 KOH/968999588
GRIZZLY 60, 27 KOH/968999590
GRIZZLY 60, 30 KOH/968999591
GRIZZLY 72, 30 KOH/968999592
GRIZZLY 60, 27 KOH/968999626
GRIZZLY 60, 30 KOH/968999627
GRIZZLY 72, 30 KOH/968999628

Please read the operator’s manual carefully and make sure you

understand the instructions before using the machine.

English

CONTENTS

Contents ..................................................................3

Introduction ..............................................................5

Congratulations .....................................................5

General ..................................................................5

Driving and Transport on Public Roads .................5

Towing ...................................................................5

Operating ...............................................................5

Good Service .........................................................6

Manufacturing Number ..........................................6

Symbols and Decals................................................7

Safety Instructions ..................................................9

General Operation .................................................9

Personal Safety Equipment .................................11

Slope Operation ..................................................11

Children ...............................................................12

Maintenance ........................................................13

Transport .............................................................16

Customer responsibilities ....................................17

Controls ..................................................................18

Control Locations ................................................18

Steering Controls .............................................19

Hour Meter ......................................................20

Parking Brake ..................................................20

Blade Switch ....................................................20

Ignition Switch .................................................21

Fuses ...............................................................21

Refueling .........................................................22

Fuel Shut Off Valve ..........................................23

Seat Adjustment Knobs ..................................23

Choke Control .................................................23

Throttle Control ................................................24

Lifting Level for Deck .......................................24

Operation ................................................................26

Training ................................................................26

Roll Bar ................................................................26

Before Starting ....................................................26

Starting the Engine ..............................................26

To start an engine with a weak battery ................31

Running ...............................................................32

Operating on hills ................................................33

Mowing Tips ........................................................34

Stopping the Engine ............................................35

Moving by Hand ..................................................36

Maintenance ............................................................37

Maintenance Schedule ........................................37

Battery ................................................................. 39

Ignition System ....................................................40

Checking the Safety System ...............................40

Checking the Engine’s Cooling Air Intake ............ 41

Checking and Adjusting the Throttle Cable..........41

Checking and Adjusting the Choke Cable ........... 41

Replacing the Air Filter ........................................42

Replacing the Fuel Filter ......................................46

Checking the Fuel Pump’s Air Filter.....................46

Checking Tire Pressures .....................................46

Checking the Parking Brake ................................ 47

Checking the V-belts ............................................47

Deck belt ..............................................................47

Checking the Blades ............................................50

Adjusting the Mower Deck ...................................52

Cleaning and Washing .........................................54

Caster Wheels .....................................................54

Hardware .............................................................54

Lubrication ..............................................................55

Lubrication Schedule ...........................................55

General ................................................................ 55

Lubricating the Cables .........................................56

Lubricating with Lubrication Schedule ................. 56

Trouble Shooting Guide .........................................63

Storage ....................................................................66

Winter Storage .....................................................66

Service .................................................................66

Wiring diagram .......................................................67

Technical Data ........................................................68

Accessories ......................................................... 74

Torque Specifi cations ..........................................74

Conformity Certifi cates ..........................................77

USA requirements ............................................... 77

Service Journal .......................................................78

Delivery Service ...................................................78

After the First 5-8 Hours ......................................79

25-Hour Service ...................................................80

50-Hour Service ...................................................81

100-Hour Service .................................................82

300-Hour Service .................................................83

At Least Once Each Year ....................................84

Warranty ..................................................................86

English-3

WARNING!
Failure to follow cautious operating practices can result in serious injury to the

operator or other persons. The owner must understand these instructions, and must
allow only trained persons who understand these instructions to operate the mower.

Each person operating the mower must be of sound mind and body and must not be
under the infl uence of any mind altering substance.

WARNING!
Engine exhaust, some of its constituents, and certain vehicle components contain

or emit chemicals known to the State of California to cause cancer and birth defects
or other reproductive harm.

WARNING!
Battery posts, terminals and related accessories contain lead and lead compounds,

chemicals known to the State of California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.

English-4

INTRODUCTION

Congratulations

Thank you for purchasing a Dixon ride-on mower. This machine is built for superior effi ciency to rapidly mow
primarily large areas. A control panel easily accessible to the operator and a hydrostatic transmission regulated by
steering controls both contribute to the machine’s performance.

This manual is a valuable document. Read the contents carefully before using or servicing the machine. The
following of instructions (use, service, maintenance, etc.) by all who operate this machine is important for the
safety of the operator and others. It can also considerably increase the life span of the machine and increase its
resale value.

If you sell your machine, be sure to give the operator’s manual to the new owner.
The fi nal chapter of this operator’s manual provides a Service Journal. Ensure that service and repair work are

documented. A well-kept service journal reduces service costs for the maintenance and affects the machine’s
resale value. Please contact your dealer for more information. Take the operator’s manual along when the
machine is taken to your dealer for service.

General

In this operator’s manual, left and right, backward and forward are used in relation to the machine’s normal driving
direction.

Continuous dedication to improve our products require that specifi cations and design are subject to change
without notice.

Driving and Transport on Public Roads

Check applicable road traffi c regulations before transporting on public roads. If the machine is transported, you
must always use approved fastening equipment and ensure that the machine is well anchored. DO NOT operate
this machine on public roadways.

Towing

Do not tow this machine, it may cause damage to the drive system.
Do not tow any trailers, etc. with this mower. They may jackknife or overturn causing damage to the mower and

possible serious injury to the operator.

Operating

This machine is constructed only for mowing grass on lawns and even ground without obstacles such as stones,
tree stumps, etc. The machine can also be used for other tasks when equipped with special accessories provided
by the manufacturer. Operating instructions for the accessories are provided with delivery. All other types of uses
are incorrect. The manufacturer’s directions concerning operation, maintenance, and repairs must be carefully
followed.

Lawn mowers and all power equipment, can be potentially dangerous if used improperly. Safety requires good
judgement, careful use in accordance with these instructions and common sense.

The machine must only be operated, maintained, and repaired by persons familiar with the machine’s special
characteristics and who are also knowledgeable about the safety instructions. Use only approved repair parts to
maintain this machine.

Accident prevention regulations, other general safety regulations, occupational safety rules, and traffi c regulations
must be followed without fail.

Unauthorized modifi cations to the design of the machine may absolve the manufacturer from liability for any
resulting personal injury or property damage.

English-5

INTRODUCTION

INTRODUCTION

Good Service

Dixon’s products are sold all over the world and only in specialized retail stores with complete service. This
ensures that you as a customer receive only the best support and service. Before the product is delivered, the
machine has, for example, been inspected and adjusted by your retailer. See the certifi cate in the Service Journal
in this operator’s manual.

When you need spare parts or support in service questions, warranty issues, etc., please consult the following
professional:

This Operator’s Manual belongs to the machine with
the manufacturing number:

Manufacturing Number

The machine’s manufacturing number can be found on the printed plate affi xed to the left in the engine
compartment. Stated on the plate, from the top are:

Engine

Transmission

• The machine’s type designation (I.D.).

• The manufacturer’s type number (Model).

• The machine’s serial number (Serial no.)

Please have the type designation and serial number available when ordering spare parts.

The engine’s manufacturing number is stamped on one of the valve covers.
The plate states:

• The engine’s model.

• The engine’s type.

• Code

Please have these available when ordering spare parts.

The wheel motors and hydrostatic pumps have a barcode decal affi xed at the rear.

English-6

SYMBOLS AND DECALS

These symbols are found on the machine and in the operator’s manual.
Study them carefully so that you know what they mean.

WARNING!
Xxxx xxxxxx xxxxx xxxx

xxxxxxxxx xxxxxx xxxxxxxxx.
xx xxxxxxxx xxxx xxxxxx.

Used in this publication to notify the reader of a risk of personal injury or death, particularly if the reader should
neglect to follow instructions given in the manual.

IMPORTANT INFORMATION
Xxxx xxxxxx xxxxx xxxx xxxxxxxxx

xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx
xxxxxx.

Used in this publication to notify the reader of a risk of material damage, particularly if the reader should neglect
to follow instructions given in the manual. Used also when there is a potential for misuse or misassembly.

RN

Reverse Neutral Fast Slow Choke Fuel

P

Warning! Parking Brake CE conformity Warning! Rotating blades, Do not touch parts
marking. Only for keep away from the
European market discharge deck

Battery acid is corrosive, explosive and fl ammable Do not stand here

Noise emissions to the
surroundings in accordance with
the European Union’s directive.
The machine’s emission is stated
in the chapter TECHNICAL DATA
and on the decals.

Only machines for European

Use protective glasses Use protective gloves

market

English-7

SYMBOLS AND DECALS

Read Shut off engine and Keep a safe Use on slopes No passengers
Operator’s remove key before distance from no greater
Manual performing any the machine than 10°
maintenance or repair work

Whole body Severing of fi ngers Do not open or Careful backing up, Careful going
exposure to and toes remove safety watch for other forward, watch for
thrown objects shields while people other people
engine is running

English-8

Moving sharp blades under cover

SAFETY

Safety Instructions

These instructions are for your safety. Read them carefully.

WARNING!
This symbol means that important safety instructions need to be emphasized.

It concerns your safety.

IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING

OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH.

General Operation

Read, understand, and follow all instructions

•

on the machine and in the manual before
starting.

• Do not put hands or feet near rotating parts

or under the machine. Keep clear of the
discharge opening at all times.

• Only allow responsible adults, who are

familiar with the instructions, to operate the
machine.

• Clear the area of objects such as rocks, toys,

wire, etc., which could be picked up and
thrown by the blades.

• Be sure the area is clear of bystanders

before operating. Stop machine if anyone
enters the area.

• Never carry passengers. The machine is only

intended for use by one person.

• Do not mow in reverse unless absolutely

necessary. Always look down and behind
before and while backing.

• Never direct discharged material toward

anyone. Avoid discharging material against
a wall or obstruction. Material may ricochet
back toward the operator. Stop the blades
when crossing gravel surfaces.

• Do not operate machine without the entire

grass catcher, discharge guard, or other
safety devices in place and working

• Slow down before turning.

• Never leave a running machine unattended.

Always turn off blades, set parking brake,
stop engine, and remove keys before
dismounting.

Read the operator’s manual before starting the machine

Clear the area of objects before mowing

8011-512

8011-513

English-9

SAFETY

• Disengage blades when not mowing. Shut

off engine and wait for all parts to come to a
complete stop before cleaning the machine,
removing the grass catcher, or unclogging
the discharge guard.

• Operate machine only in daylight or good

artifi cial light.

• Do not operate the machine while under the

infl uence of alcohol or drugs.

• Watch for traffi c when operating near or

crossing roadways.

• Use extra care when loading or unloading

the machine into a trailer or truck.

• Always wear eye protection when operating

machine.

• Data indicates that operators, age 60

years and above, are involved in a large
percentage of riding mower-related injuries.
These operators should evaluate their ability
to operate the riding mower safely enough to
protect themselves and others from serious
injury.

• Follow the manufacturer’s recommendation

for wheel weights or counterweights.

• Anyone who operates this machine must fi rst

read and understand this Operation Manual.
Local laws may regulate the age of the user.

• Keep machine free of grass, leaves or other

debris buildup which can touch hot exhaust
/ engine part and burn. Do not allow the
mower deck to plow leaves or other debris
which can cause buildup to occur. Clean any
oil or fuel spillage before operating or storing
the machine. Allow machine to cool before
storage.

Never take passengers

8011-520

WARNING!
Engine exhaust and certain

vehicle components contain
or emit chemicals considered
to cause cancer, birth defects,
or other reproductive system
damage. The engine exhaust
contains carbon monoxide,
which is a odorless, colorless,
poisonous gas. Do not use the
machine in enclosed spaces.

English-10

Personal Safety Equipment

WARNING!
When using the machine, approved personal protective equipment (shown in

illustrations) shall be used. Personal protective equipment cannot eliminate the
risk of injury but it will reduce the degree of injury if an accident does happen.
Ask your retailer for help in choosing the right equipment.

Make sure that you have fi rst aid equipment

•

close at hand when using the machine.

• Never use the machine when barefoot.

• Always wear protective shoes or boots,

preferably with steel toe caps.

• Always wear approved protective glasses or

a full visor when assembling or driving.

• Always wear gloves when handling the

blades.

• Never wear loose clothing that can get

caught in moving parts.

• Use ear protectors to avoid damage to

hearing.

SAFETY

Slope Operation

Slopes are a major factor related to loss of control and
tip-over accidents, which can result in severe injury or
death. Operation on all slopes requires extra caution. If
you cannot back up the slope or if you feel uneasy on
it, do not mow it.

• Mow up and down slopes (10 degrees
maximum), not across.

• Watch for holes, ruts, bumps, rocks, or
other hidden objects. Uneven terrain could
overturn the machine. Tall grass can hide
obstacles.

• Choose a low ground speed so that you will
not have to stop while on the slope.

• Do not mow on wet grass. Tires may lose
traction.

• Avoid starting, stopping, or turning on a
slope. If the tires lose traction, disengage the
blades and proceed slowly straight down the
slope.

• Keep all movement on the slopes slow and
gradual. Do not make sudden changes in
speed or direction, which could cause the
machine to roll over.

• Use extra care while operating machine with

grass catchers or other attachments; they
can affect the stability of the machine.

• Do not use on steep slopes.

Personal protective equipment

8011-670a

6003-004

Mow up and down, not side to side

WARNING!
Do not drive up or down hills

with slopes greater than 10
degrees. And do not drive across
any slopes.

English-11

SAFETY

• Do not try to stabilize the machine by putting

your foot on the ground.

• Do not mow near drop-offs, ditches, or

embankments. The machine could suddenly
roll over if a wheel is over the edge or if the
edge caves in.

Children

Tragic accidents can occur if the operator is not
alert to the presence of children. Children are often
attracted to the machine and the mowing activity.
Never assume that children will remain where you last
saw them.

• Keep children out of the mowing area and in

the watchful care of a responsible adult other
than the operator.

• Be alert and turn machine off if a child enters

the area.

• Before and while backing, look behind and

down for small children.

• Never carry children, even with the blades

shut off. They may fall off and be seriously
injured or interfere with safe machine
operation. Children who have been given
rides in the past may suddenly appear in
the mowing area for another ride and be run
over or backed over by the machine.

• Never allow children to operate the machine.

• Use extra care when approaching blind

corners, shrubs, trees, or other objects that
may block your view of a child.

8011-509

Be extra cautious when driving on slopes

8011-517

Never allow children to operate the machine

English-12

8011-518

Keep children away from work area

SAFETY

Maintenance

WARNING!
The engine must not be started when the driver’s fl oor plate or any protective

plate for the mower deck’s drive belt is removed.

Safe Handling of Gasoline

To avoid personal injury or property damage, use
extreme care in handling gasoline. Gasoline is
extremely fl ammable and the vapors are explosive.

• Extinguish all cigarettes, cigars, pipes, and
other sources of ignition.

• Use only approved gasoline container.

• Never remove gas cap or add fuel with the
engine running. Allow engine to cool at least
two (2) minutes before refueling.

• Never fuel the machine indoors.

• Never store the machine or fuel container
where there is an open fl ame, spark, or pilot
light such as on a water heater or other
appliances.

• Before you begin refueling, minimize the
risk of static electricity by touching a metal
surface.

• Never fi ll containers inside a vehicle or on a

truck or trailer bed with plastic liner. Always
place containers on the ground away from
your vehicle when fi lling.

• Remove gas-powered equipment from the

truck or trailer and refuel it on the ground.
If this is not possible, then refuel such
equipment with a portable container, rather
than from a gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times until
fueling is complete. Do not use a nozzle lock­open device.

• If fuel is spilled on clothing, change clothing

immediately.

• Never overfi ll fuel tank. Replace gas cap and

tighten securely.

• Do not start the engine near spilled fuel.

• Never use gasoline as a cleaning agent.

8011-516

Never fi ll the fuel tank indoors

WARNING!
The engine and the exhaust

system, become very hot
during operation.

Risk for burns if touched.
Allow engine and exhaust

system to cool at least two (2)
minutes before refueling.

English-13

• If leaks arise in fuel system, engine must not

be started until problem has been resolved.

• Check the fuel level before each use and

leave space for the fuel to expand, because
the heat from the engine and the sun may
otherwise cause the fuel to expand and
overfl ow.

General Maintenance

Never operate machine in a closed area.

•

• Keep all nuts and bolts tight to be sure the

equipment is in safe working condition.

• Never tamper with safety devices. Check

their proper operation regularly.

• Keep machine free of grass, leaves, or other

debris buildup. Clean oil or fuel spillage
and remove any fuel-soaked debris. Allow
machine to cool before storing.

• If you strike a foreign object, stop and

inspect the machine. Repair, if necessary,
before restarting.

• Never make any adjustments or repairs with

the engine running.

• Check grass catcher components and the

discharge guard frequently and replace with
manufacturer’s recommended parts, when
necessary.

• Mower blades are sharp. Wrap the blade or

wear gloves, and use extra caution when
servicing them.

• Check brake operation frequently. Adjust and

service as required.

• Maintain or replace safety and instruction

labels, as necessary.

• Do not modify safety equipment. Check

regularly to be sure it works properly. The
machine must not be driven with defective
or unmounted protective plates, protective
cowlings, safety switches, or other protective
devices.

• Do not change the settings of governors and

avoid running the engine with overly high
engine speeds. If you run the engine too fast,
you risk damaging the machine components.

• Be very careful when handling battery acid.

Acid on skin can cause serious corrosive
burns. If you spill battery acid on your skin,
rinse immediately with water.

• Acid in the eyes can cause blindness,

contact a doctor immediately.

SAFETY

8011-515

Never drive the machine in an enclosed space

Use protective glasses for
maintenance work.

WARNING!
The battery contains lead and

lead compounds, chemicals
that are considered to cause
cancer, birth defects, and other
reproductive system damage.
Wash your hands after handling
the battery.

English-14

SAFETY

• Be careful when servicing the battery.
Explosive gases form in the battery. Never
perform maintenance on the battery when
smoking or near open fl ames or sparks.

• The battery can explode and cause serious
injury/damage.

• Ensure that nuts and bolts, especially the

fastening bolts for the blade attachments,
are properly tightened, torqued and that the
equipment is in good condition.

• Do not modify safety equipment. Check

regularly to be sure it works properly. The
machine must not be driven with defective
or unmounted protective plates, protective
cowlings, safety switches, or other protective
devices.

• Do not change the settings of governors and

avoid running the engine with overly high
engine speeds. If you run the engine too fast,
you risk damaging the machine components.

• Sparking can occur when working with the

battery and the heavy cables of the starter
circuit. This can cause battery explosion,
fi re or eye injury. Sparking in this circuit can
not occur after the chassis cable (normally
negative, black) is removed from the battery.

6003-009

Do not smoke when performing maintenance on the battery.
The battery can explode and cause serious injury/damage.

WARNING!
Avoid electrical sparking and its

consequences by the following
routines:

• Use protective goggles.

• Ensure that the fuel fi ller cap is mounted

tightly and no fl ammable substances is
stored in an open vessel.

• Never work with the starter circuit if there is

spilled fuel.

• Disconnect the chassis cable from the

battery fi rst and reconnect it last.

• Do not make a bridge short circuit across the

starter relay to run the starter.

• Never use the machine indoors or in spaces
lacking proper ventilation. The exhaust
fumes contain carbon monoxide, an
odorless, poisonous, and lethal gas.

• Stop and inspect the equipment if you run

over or into anything. If necessary, make
repairs before starting.

• Never make adjustments with the engine

running.

8009-728

Risk of sparking

English-15

• The machine is tested and approved only

with the equipment originally provided or
recommended by the manufacturer. Only use
approved repair parts for the machine.

• The blades are sharp and can cause

cuts and gashes. Wrap the blades or use
protective gloves when handling them.

• Check the parking brake’s functionality

regularly. Adjust and service as necessary.

• The mulch blades should only be used in

familiar areas when higher quality mowing is
desired.

• Reduce the risk of fi re by removing grass,

leaves, and other debris that may have
accumulated on the machine. Allow the
machine to cool before putting it in storage.

• Regularly clean deck and underside of

deck, avoid spraying engine and electrical
components with water.

Transport

The machine is heavy and can cause serious

•

crushing injuries. Be extra cautious when it
is loaded on or unloaded from a vehicle or
trailer.

• Use an approved trailer to transport the

machine. Activate the parking brake, turn off
the fuel supply, and fasten the machine with
approved fastening devices, such as bands,
chains, or straps, when transporting.

• Do not operate this machine on public

roadways.

• Check and abide by local traffi c regulations

before transporting the machine on any road.

• Do not tow this machine, it may cause

damage to the drive system.

• Do not tow any trailers, etc. with this mower.

They may jackknife or overturn causing
damage to the mower and possibly serious
injury to the operator.

• Load the unit onto truck or trailer by driving

up ramps of suitable strength using a slow
speed. Do not lift! The machine is not
intended to be lifted by hand.

SAFETY

8011-515

Never drive the machine in an enclosed space

WARNING!
Escaping hydraulic oil under

pressure can have suffi cient
force to penetrate the skin,
causing serious injury. If injured
by escaping fl uid, see a doctor
at once. Serious infection or
reaction can develop if proper
medical treatment is not
administered immediately.

IMPORTANT INFORMATION
The parking brake is not suffi cient

to lock the machine in place during
transport. Ensure that the machine is
well fastened to the transport vehicle.
Always reverse the machine onto the
transport vehicle to avoid tipping it over.

English-16

SAFETY

Roll over Protection system ROPS

The ROPS increases the basic weight of the unit by 42 lbs/19 kg. The ROPS on the US units are standard, on the
European units the ROPS is an accessory.

WARNING!
The structures capability may be impaired by structural damage if overturned, or

alteration occurs. If any of these conditions take place, the total structure MUST
be replaced.

Do not use ROPS as a lifting, attaching or anchoring point.
Do not use ROPS for wrecking or towing.
Do not exceed Max GVW: 2822 lbs/1283 kg.
Read machine operator´s manual before each use.
Securely fasten your seat belt if the unit has a ROPS.
Where possible, avoid operating the unit near ditches, embankments and holes.
Reduce speed when turning, crossing slopes and on rough, slick or muddy surfaces.
Stay off slopes too steep for safe operation.
Watch where you are going, especially at row ends, on roads and around trees.
Do not permit others to ride.
Operate the mower smoothly - no jerky turns, starts or stops.
When mower is stopped, set brakes securely and use park brake.
If any part of ROPS is damaged, the entire ROPS must be replaced.
Check all bolts including seat belt for correct torque before each use.
Check ROPS structure for damage before each use.
ROPS bar is NOT intended for use in sub zero temperatures.

Customer responsibilities

Read and observe the safety rules.

•

• Follow a regular schedule in maintaining, caring for and using your mower.

• Follow the instructions under “Maintenance” and “Storage” sections of this

owner’s manual.

WARNING!
This mower is equipped with an internal combustion engine and should not be

used on or near any unimproved forest-covered, bush-covered or grass-covered
land unless the engine’s exhaust system is equipped with a spark arrester
meeting applicable local or state laws (if any). If a spark arrester is used, it
should be maintained in effective working order by the operator.

A spark arrester for the muffl er is available through your authorized Dixon dealer.

English-17

CONTROLS

Controls

This operator’s manual describes the Dixon Zero
Turn Rider. The rider is fi tted with a Kohler four-stroke
overhead valve engine developing 27 - 30 horse
power.

Transmission from the engine is made via two belt­driven hydraulic pumps, which in turn drive a hydraulic
motor for each drive wheel. Using the left and right
steering controls, the fl ow is regulated and thereby the
direction and speed.

Control Locations

Zero Turn Rider

7

6

7

1. Motion control levers

2. Hour meter

3. Parking brake

4. Blade switch

5. Ignition switch

6. Fuses

7. Fuel tank cap

11

8

2

10

3

4

12

5

8. Fuel shut off valve

9. Seat adjustment lever

10. Choke control
1 1. Throttle control

12. Cutting height adjuster

13. Deck lift (foot assist)

13

1

9

English-18

CONTROLS

1. Steering Control Levers

The machine’s speed and direction are continuously
variable using the two steering controls. The steering
controls can be moved forward or backward about a
neutral position. Furthermore, there is a neutral posi­tion, which is locked if the steering controls are moved
outward.

When both controls are in the neutral position (N), the
machine stands still.

By moving both controls an equal amount forward or
backward, the machine moves in a straight line for­ward or backward respectively.

In order, for example, to turn right while moving for­ward, move the right control towards the neutral posi­tion. The rotation of the right wheel is reduced and the
machine turns to the right.

Steering controls

8011-789

Zero turn can be achieved by moving one control
backward (behind the neutral position) and carefully
moving the other steering control forward from its neu­tral position. The rotation direction when zero turning is
determined by which steering control is moved back­ward behind the neutral position. If the left steering
control is pulled backward, the machine turns to the
left. Use extra care when using this maneuver.

If the steering controls are in uneven positions when
standing still or do not fi t in the slots for moving the
controls outward, they can be adjusted.

Tracking

If the mower is not tracking straight, check the air
pressure in both rear tires. Recommended air pressure
is 15 psi. (1 bar) Tracking must be checked on a fl at
and level concrete or blacktop surface. If the unit still
does not track straight contact your Dixon workshop
for adjustments.

WARNING!
The machine can turn very

rapidly if one steering control
is moved much further forward
than the other.

1. Forward

2. Neutral

3. Neutral slot, Neutral lock

4. Reverse

Motion control lever, right side

1

2

3

4

8011-7912

English-19

CONTROLS

2. Hour Meter

The hour meter displays the total operating time.
It will fl ash CHG OIL (Change Oil) at 50 hour intervals.

The fl ash duration is one hour before and one hour
after the interval. The CHG OIL icon will come on
and shut off automatically. The hour meter can not be
manually reset.

3. Parking Brake

IMPORTANT INFORMATION
The machine must stand absolutely still

when applying the parking brake. Always
set the parking brake before dismounting.
Release the parking brake before moving
the mower.

The parking brake is found on the left of the machine.
Pull the lever backward to activate the brake and
forward to release it.

4. Blade switch

In order to engage the mower deck, pull the knob out;
the mower blades are disengaged when the knob is
depressed.

Hour meter

Parking brake not activated

8050-147

8011-711

English-20

Blade Switch

8050-151

CONTROLS

5. Ignition Switch

The ignition key is placed on the control panel and is
used to start and stop the engine.

6. Fuses

8050-147

Ignition Switch

The fuses are located in a holder at the right hand side
of the battery compartment. They are fl at pin fuses of
the same type used in automobiles.

There are three fuses as well as socket for one spare
fuse.

Fuse ratings and functions:

• 20 A, Primary fuse.

• 7.5 A, Mower deck coupling.

• 7.5 A, Accessory outlet.

• Socket for spare fuse.

Fuses

8011-746

English-21

CONTROLS

7. Refueling

Read the safety instructions before refueling. The
machine has two fuel tank, just behind the seat. The
tanks take 5.7 gallons (22 liters) each.

Make sure the fuel caps are properly tightened and the
cap gasket is not damaged.

The engine will run on a minimum of 85-octane
unleaded gasoline (no oil mix). Environmentally
adapted alkylate gasoline can be used. See also
Technical Data concerning ethanol fuel. Methanol fuel
is not allowed. Do not use E85 alcohol based fuel.
Damage to engine and components may occur.

WARNING!
Gasoline is highly fl ammable.

Observe caution and fi ll the
tank outdoors (see the safety
instruction).

8011-524

Fuel tanks

IMPORTANT INFORMATION

WARNING!
The engine and the exhaust

system, become very hot during
operation.

Risk for burns if touched.
Allow engine and exhaust

system to cool at least two (2)
minutes before refueling

WARNING!
Fill to bottom of fi ller neck. Do

not overfi ll. Wipe off any spilled
oil or fuel. Do not store, spill
or use gasoline near an open
fl ame.

Experience indicates that alcohol blended
fuels (called gasohol, ethanol or methanol)
can attract moisture which leads to
separation and formation of acids during
storage. Acidic gas can damage the fuel
system of an engine while in storage. To
avoid engine problems, the fuel system
should be emptied before storage of 30
days or longer. Drain the gas tank, start the
engine and let it run until the fuel lines and
carburetor are empty. Use fresh fuel the
next season. See Storage Instructions for
additional information. Never use engine
or carburetor cleaners in the fuel tank or
permanent damage may occur.

When operating in temperatures below 32° F. (0° C.),
use fresh, clean winter grade gasoline to help insure
good cold weather starting.

English-22

CONTROLS

8. Fuel Shut Off Valve

The fuel shut off valve is located at the right rear of the
seat. The valve has three positions; right tank, left tank
and center is the off position.

9. Seat Adjustment Lever

The seat can be adjusted lengthways. When making
adjustments, the lever under the front edge of the
seat is moved to the left (as seen by the driver in the
seat), after which the seat can be moved backward or
forward.

10. Choke Control

The choke control is used for cold starts in order to
provide the engine with a richer fuel mixture.

For cold starts the control should be pushed to the on
position.

Fuel shut off valve

Lengthways adjustment

8011-506

8011-441

Choke control

8050-148

English-23

CONTROLS

11. Throttle Control

The throttle control regulates the engine speed and
thereby the rate of rotation of the blades, assuming the
blade switch is pulled out, see Engaging the Mower
Deck.

In order to increase or decrease the engine speed, the
control is moved forward or back respectively.

Avoid idling the engine for long periods, as there is a
risk of fouling the spark plugs.

USE FULL THROTTLE WHEN MOWING, for best
mower performance and battery charging.

12. Lifting Lever for the Mower Deck

The lifting lever is used to place the mower deck in
the transport position or one of the 17 different cutting
height positions.

The cutting height is set by placing a peg in the hole
for the desired cutting height and the peg is then
locked on the inside (hidden in the illustration) with the
supplied pin.

Pull the lever backward to the locked position to
engage the transport position. The deck is then raised.

Depress the lock handle, counter hold, and move the
lifting lever forward toward the peg to engage the set
cutting height. The deck is then lowered.

The lifting lever can also be used to temporarily adjust
the cutting height, such as when passing a minor
bump in the lawn.

Throttle control

The mower deck’s lifting lever

8050-150

8011-525-1

IMPORTANT INFORMATION
In order to obtain an even cutting height it

is important that the air pressure in all four
tires is the same 15 psi (1 bar).

IMPORTANT INFORMATION
Always use the high position to transport.

English-24

CONTROLS

6.0

5.5

4.5

Pump release valves

IMPORTANT INFORMATION
Only rotate valve ¼ - ½ turn to release

system.
Tighten the valve moderately.
Do not overtighten the valve when closing.

That can damage the valve seat.

Pump release valves are located at the pumps. They
are used to release the system so the machine may be
moved by hand when not running. Tilt seat forward to
gain access to the pumps. Use a 5/8" wrench to open
both valves.

Tracking

1. Tracking adjustment is done using the
tracking bolts. The tracking bolts act as
limiting devices for the motion control levers
when in the full-forward position.

2. Start by loosening jam nut on right tracking
bolt. Back the tracking bolt out until fl ush with
nut.

3. Loosen left bolt and back out until fl ush with
nut.

4. Move unit to an open, unobstructed area
such as an empty parking lot or open fi eld for
tracking adjustment.

5. Test operation of the unit by driving it at full
throttle and full forward position on both
motion control levers. Gradually turn in the
tracking bolt on the right hand side until the
unit noticeably starts drifting right.

6. Stop the unit and tighten right jam nut in this
position.

7. Restart the unit and drive forward at full
throttle with both motion control levers in full
forward position. Gradually turn in the left bolt
until unit tracks straight. Tighten jam nut.

Pump release valve

1

5.5

5.0

4.5

1. Tracking bolt

Tracking adjustment

8011-507

6.0

Accessories

For mulching, there is a BioClip attachment available.
This is mounted underneath the mower deck and
consists of control plates and BioClip blades.

English-25

OPERATION

Operation

Read “Safety Instructions” section and following pages, if you are unfamiliar with the machine.

Training

Zero turn mowers are far more maneuverable than typical riding mowers due to their unique steering capabilities.
We suggest that this section be reviewed in its entirety prior to attempting to move the mower under its own

power. Additionally, we suggest when fi rst operating the mower, use a reduced throttle speed and reduced ground
speed by NOT moving control levers to the furthest forward or reverse positions during initial operation, or until
operator becomes comfortable with controls. We also suggest fi rst time users, or new users to Zero Turn mowers
to become familiar with the mower’s movement on a hard surface, such as concrete or blacktop PRIOR to
attempting to operate on turf. Until operator becomes comfortable with mower controls and zero turning capability,
they may damage turf due to overly aggressive maneuvers.

To move forward and backward

The direction and speed of the mower’s movements is effected by the movement of the control lever(s) on each
side of mower. The left control lever controls the left wheel. The right control lever controls the right wheel.

IMPORTANT INFORMATION
When control levers are in the reverse

position they return to neutral when
released. This may cause the mower to
suddenly stop.

First time users should push mower (see “Moving by Hand” in the “Operation” section) to an open, fl at area,
without other people or vehicles/obstacles nearby. In order to move unit under its own power, the operator must
be in the seat, start engine (see “Before Starting” in “Operation” section), adjust engine speed to idle, disengage
parking brake, do not engage blades at this time, rotate control levers inward. As long as the control levers
have not been moved forward or backwards, mower will not move. Slowly move both control levers forward
slightly. This will allow mower to start moving forward in a straight line. Pull back on control levers to the neutral
position and mower should stop moving. Pull back slightly on control levers, this will allow mower to start moving
backwards. Push forward on control levers to the neutral position and mower should stop moving.

To turn to the right

While moving in a forward direction, pull the right lever back towards the neutral position while maintaining
the position of the left lever, this will slow the rotation of the right wheel and cause the machine to turn in that
direction.

To turn to the left

While moving in a forward direction pull the left lever back towards the neutral position while maintaining the
position of the right lever, this will slow the rotation of the left wheel and cause the machine to turn in that
direction.

To zero turn

While moving in a forward direction, fi rst pull both control levers back until the mower stops or slows dramatically.
Then by alternating one lever slightly to the forward position and the other in the reverse position.

English-26

OPERATION

Roll bar and safety belt

Operate the unit with the roll bar in the raised and
locked position and use the seat belt. There is no
rollover protection when the roll bar is down. If it is
necessary to lower roll bar, do not wear the seat belt.
Raise the roll bar as soon as clearance permits.

WARNING!
The seat belt must be used when

the roll bar is in upright position.

Before Starting

• Read the sections Safety Instructions and
Controls before starting the machine.

• Perform the daily maintenance before
starting (see Maintenance Schedule in the
Maintenance section).

• Check that there is suffi cient fuel in the fuel
tank.

• Adjust the seat to the desired position.

The following conditions must be fulfi lled before the
engine can be started:

• The driver must be seated on the seat.

• The blade switch for engaging the mower
blades must be depressed.

• The parking brake must be on.

• Both steering controls must be in the locked
(outer) neutral position.

Roll bar in upright position

8011-464-1

Starting the Engine

1. Sit on the seat.

2. Raise the mower deck by pulling the lifting
lever backward to the locked position
(transport position).

3. Activate the parking brake.

Start conditions

Raise the mower deck

8011-527-1

8011-552

English-27

OPERATION

4. Disengage the mower blades by depressing

the blade switch.

5. Move the steering controls outward to the

locked (outer) neutral position.

8050-151

Depress the control for disengaging the mower deck

6. Move the throttle to the middle position.

English-28

8011-526

Steering controls in the outward, locked neutral position

8050-150

Set the throttle

7. If the engine is cold, the choke control
should be pushed to its extents.

8. Open the fuel valve for the selected fuel
tank.

8050-148

Set the choke control

9. Press in and turn the ignition key to the start
position.

8011-506

Open the fuel valve

STOP

8050-780

Turn to the start position

English-29

OPERATION

10. When the engine starts, immediately release

the ignition key back to the run position.

IMPORTANT INFORMATION
Do not run the starter for more than 5

seconds each time. If the engine does
not start, wait about 10 seconds before
retrying.

STOP

11. Gradually pull choke control back when the

engine has started.

12. Set the desired engine speed with the

throttle. Allow the engine to run at a
moderate speed, “half throttle”, for 3-5
minutes before loading it too heavily. USE
FULL THROTTLE WHEN MOWING (no
choke).

Return to run position

8050-781

8050-148

Gradually pull choke control back

English-30

WARNING!
Engine exhaust and certain

vehicle components contain
or emit chemicals considered
to cause cancer, birth defects
or other reproductive system
damage. The engine exhaust
contains carbon monoxide,
which is a odorless, colorless,
poisonous gas. Do not use the
machine in enclosed spaces.

8050-150

Set the engine speed

OPERATION

To start an engine with a weak battery

WARNING!
Lead-acid batteries generate

explosive gases. Keep sparks,
fl ame and smoking materials
away from batteries. Always
wear eye protection when
around batteries.

If your battery is too weak to start the engine, it should
be recharged. (See “Battery” in the Maintenance
Section.)

If “jumper cables” are used for emergency starting,
follow this procedure:

IMPORTANT INFORMATION
Your mower is equipped with a 12-volt

negative grounded system. The other
vehicle must also be a 12-volt negative
grounded system. Do not use your mower
to start other vehicles.

To attach jumper cables

• Connect each end of the RED cable to the
POSITIVE (+) terminal on each battery,
taking care not to short against chassis.

• Connect one end of the BLACK cable to the
NEGATIVE (-) terminal of the fully charged
battery.

• Connect the other end of the BLACK cable
to a good CHASSIS GROUND on the mower
with the discharged battery, away from the
fuel tank and battery.

To remove cables, reverse order

• Remove BLACK cable fi rst from chassis and

then from the fully charged battery.

• Remove RED cable last from both batteries.

8011-642

Jumper cable connection

English-31

OPERATION

Running

1. Release the parking brake by moving the
lever downward.
Your mower is equipped with an operator
presence system. When the engine is
running, any attempt by the operator to leave
the seat without fi rst setting the parking
brake will shut off the engine.

2. Move the steering controls to the neutral
position (N).

IMPORTANT INFORMATION
The mower deck’s anti-scalp rollers should

be evenly adjusted.

3. Select the cutting height by adjusting the
cutting height pin. Release latch and lower
deck to set cutting height.

Released parking brake

8011-711

WARNING!
Ensure that no one is near

mower when engaging blade
switch.

4. Make sure the work area is free from objects
that could be thrown by the rotating blades.

5. Engage the mower deck by pulling out the
blade switch.

6. Move throttle control to full throttle.

7. The machine’s speed and direction are
continuously variable using the two steering
controls. When both controls are in the
neutral position, the machine stands still.
By moving both controls an equal amount
forward or backward, the machine moves
in a straight line forward or backward
respectively.
In order, for example, to turn right while
moving forward, move the right control
towards the neutral position. The rotation of
the right wheel is reduced and the machine
turns to the right.
Turning on the spot (zero turn) can be
achieved by moving one control backward
(behind the neutral position) and carefully
moving the other steering control forward
from its neutral position.

English-32

8011-561-1

Cut height selection

8050-151

Engaging the mower deck

OPERATION

Operating on hills

Read the Safety Instructions “Driving on Slopes” in the
“Safety Instructions”.

WARNING!
Do not drive up or down hills with

slopes greater than 10 degrees.
Do not drive across slopes.

• The slowest speed possible should be used

before starting up or down hills.

• Avoid stopping or changing speed on hills.

• If stopping is absolutely necessary, pull drive

levers into the neutral position and push
to the outside of the unit and engage the
parking brake.

IMPORTANT INFORMATION

8011-640-1

Stopping conditions

Control levers return to neutral when
released. This may cause the mower to
suddenly stop.

• To restart movement, release the parking

brake.

• Pull the control levers back to the center

of the mower and press forward to regain
forward motion.

• Make all turns slowly.

Released parking brake

8011-711

English-33

OPERATION

Mowing Tips

• Observe and fl ag rocks and other fi xed
objects to avoid collisions.

• Begin with a high cutting height and reduce it
until the desired mowing result is attained.
The average lawn should be cut to 2½”

(64 mm) during the cool season and over 3”

(76 mm) during the hot months. For healthier
and better looking lawns, mow often after
moderate growth.
For best cutting performance, grass over 6”
(15 cm) in height should be mowed twice.
Make the fi rst cut relatively high; the second
to the desired height.

• The mowing result will be best with a high
engine speed (the blades rotate rapidly) and
low speed (the rider moves slowly). If the
grass is not too long and dense, the driving
speed can be increased without negatively
affecting the mowing result.

• The fi nest lawns are obtained by mowing
often. The lawn becomes more even and the
grass clippings more evenly distributed over
the mown area. The total time taken is not
increased as a higher operating speed can
be used without poor mowing results.

• Avoid mowing wet lawns. The mowing result
is poorer because the wheels sink into
the soft lawn, clumps build, and the grass
clippings fasten under the cowling.

• Hose the mower deck underside with water
after each use. When cleaning, the mower
deck shall be raised into the transport
position. Make sure the mower is cooled and
the engine is off.

• Use compressed air to clean top surface
of the deck. Avoid fl ooding water on top
surface, engine and electrical components.

• When the mulching kit is used, it is important
that the mowing interval is frequent.

WARNING!
Clear the lawn of stones and

other objects that can be thrown
out by the blades.

8011-603

Mowing pattern

WARNING!
Never drive the rider on terrain

that slopes more than 10 degrees.
Mow slopes up and down, never
side to side. Avoid sudden
directional changes.

English-34

OPERATION

Stopping the Engine

Allow the engine to idle a minute in order to attain
normal operating temperature before stopping it, if
it has been worked hard. Avoid idling the engine for
longer periods, as there is a risk of the spark plugs
fouling.

1. Disengage the mower deck by depressing
the blade switch.

8050-151

Disengage the mower deck

2. Raise the mower deck by depressing the
pedal forward to the transport position.

3. When the machine is standing still, activate
the parking brake by pulling the lever
upward.

4. Move the throttle to the minimum position
(tortoise symbol). Turn the ignition key to the
stop position.

5. Move the steering controls outward.

6. Remove key. Always remove key when
leaving the mower to prevent unauthorized
use.

Moving by Hand

IMPORTANT INFORMATION
Leaving the ignition switch in any other

position than “OFF” will cause the battery
to be discharged and the hour meter to
accumulate hours.

8011-552

Raise the mower deck

English-35

OPERATION

In order for the machine to be moved with the engine
turned off, the vent screws on both hydraulic pumps
must be opened
move mower by hand.

1

/4 -1/2 turn.Open both vent screws to

WARNING!
No adjustments or maintenance

to be carried out unless:

♦ the engine stopped
♦ the ignition key removed
♦ the parking brake activated

8011-507

Vent screw on the hydraulic pump

English-36

MAINTENANCE

Maintenance

Maintenance Schedule

The following is a list of maintenance procedures that must be performed on the machine. For those points not
described in this manual, visit an authorized service workshop. An annual service carried out by an authorized
service workshop is recommended to maintain your machine in the best possible condition and to ensure safe
operation.

Read “Maintenance” in the Safety Instructions section.

1)

First change after 5-8 hours. When operating with a heavy load or at high ambient temperatures, replace every 50 hours.

replacement are required more often.

3)

For daily use, the machine should be lubricated twice weekly.

4)

Performed by authorized service workshop.

z = Described in this manual
 = Not described in this manual

2)

In dusty conditions, cleaning and

Daily Weekly

Maintenance Before After

Check the parking brake
Check the engine’s oil level (every refueling)
Check the safety system
Check for fuel and oil leakages
Check/clean the engine’s cooling air intake
Check the mower deck
Check hardware (screws, nuts, etc.)
Clean under the mower deck
Start the engine and blades, listen for unusual sounds
Check for damage
Thoroughly clean around the engine
Clean around belts, belt pulleys, etc.

z

z

z


z

z
z

z








Check the tire pressures
Check battery
Sharpen/Replace mower blades
Check the fuel pump’s air fi lter
Clean the engine’s cooling air intake

2)

2)

At

Maintenance interval

least

in hours

once
each

year

25 50 100 300

z

z
z

z

z

z

Clean the air cleaner’s pre-fi lter 2) (foam)
Clean the air cleaner’s fi lter cartridge

2)

(paper fi lter)
Check/adjust the parking brake
Inspect muffl er/Spark arrester

z

z

z

z





English-37

MAINTENANCE

Daily Weekly

Maintenance Before After

Check/adjust throttle and choke cables
Check the condition of belts, belt pulleys, etc.
Change the engine oil

1)

Replace the engine oil fi lter
Clean/replace the spark plugs
Replace the fuel fi lter
Replace the air fi lter (paper fi lter)

2)

Check the caster wheels (every 200 hours)
Clean the cooling fi ns

2)

Replace the air cleaner’s pre-fi lter 2) (foam)
Check/adjust the mower deck
Check the engine valve clearance
Perform the 300-hour service

4)

4)

Lubricate according to Lubrication Schedule
Check hydraulic oil at reservoir
Change hydraulic oil & fi lter (200 hours)
Clean fi ns of oil cooler (Kohler)

z

At

Maintenance interval

least

in hours
once
each

year

25 50 100 300

z

z

z
z

z

z

z

z

z

z

z
z

z

z


z

z

z

z





z

zzzz

z

z

z

1)

First change after 5-8 hours. When operating with a heavy load or at high ambient temperatures, replace every 50 hours.

conditions, cleaning and replacement are required more often.
authorized service workshop.

z

= Described in this manual



= Not described in this manual

3)

For daily use, the machine should be lubricated twice weekly.

WARNING!
Before performing any service or adjustment checklist:

• Engage the parking brake.

• Place the Blade-switch in the disengaged position.

• Turn the ignition switch to “OFF” position and remove the key.

• Make sure the blades and all moving parts have completely stopped.

• Disconnect the spark plug wire from all spark plugs and place the wire where it
cannot come in contact with the plug.

English-38

2)

In dusty

4)

Performed by

MAINTENANCE

Battery

Your mower is equipped with a maintenance free
battery and does not need servicing. However,
periodic charging of the battery with an automotive
type battery charger will extend its life.

• Keep battery and terminals clean.

• Keep battery bolts tight.

• Recharge at 6-10 amperes for 1 hour

To clean battery and terminals

Corrosion and dirt on the battery and terminals can
cause the battery to “leak” power.

1. Open the terminal access doors.

2. Disconnect BLACK battery cable fi rst, then the
RED battery cable and remove the battery from the
machine.

3. Rinse the battery with plain water and dry.

4. Clean terminals and battery cable ends with wire
brush until shiny.

5. Coat terminals with grease or petroleum jelly

6. Reinstall battery.

Always use protective glasses
when handling the battery.

IMPORTANT INFORMATION
Do not attempt to open or remove caps

or covers. Adding or checking level of
electrolyte is not necessary.

Always use two wrenches for the terminal
screws

WARNING!
Do not short battery terminals by

allowing a wrench or any other
object to contact both terminals at
the same time. Before connecting
battery, remove metal bracelets,
wristwatch bands, rings, etc.

Replacing battery

1. Lift Seat and rotate forward.

2. Remove the red terminal guard.

3. Using two ½" wrenches disconnect BLACK battery
cable then RED battery cable.

4. Remove the knobs and remove battery hold
downs.

5. Carefully remove the battery from the mower.

6. Install new battery with terminals in the same
position as the old battery.

7. Reinstall battery hold downs.

8. First connect RED battery cable to positive (+)
battery terminal with hex bolt and hex nut.

9. Connect BLACK grounding cable to negative (-)
battery terminal with remaining hex bolt and hex
nut.

10. Fit the terminal guard.

1 1. Lower seat.

Positive terminal must be
connected fi rst to prevent sparks
from accidental grounding.

8011-466

Battery installation

English-39

MAINTENANCE

Ignition System

The engine is equipped with an electronic ignition
system. Only the spark plugs require maintenance.

For recommended spark plugs, see Technical Data.

1. Remove the ignition cable boot and clean around
the spark plug.

2. Remove the spark plug with a spark plug socket
wrench.

3. Check the spark plug. Replace the spark plug
if fouled, the electrodes are burned and if the
insulation is cracked or damaged. Clean the spark
plug with a steel brush if it is to be reused.

4. Measure the electrode gap with a gapping tool.
The gap should be .030” (0.75 mm). Adjust as
necessary by bending the side electrode.

5. Reinsert the spark plug, turning by hand to avoid
damaging the threads.

6. After the spark plug is seated, tighten it using
a spark plug wrench so that the washer is
compressed. A used spark plug should be turned

1

/8 of a turn from the seated position. A new spark
plug should be turned ¼ a turn from the seated
position.

7. Replace the ignition cable.

IMPORTANT INFORMATION
Fitting the wrong spark plug type can

damage the engine.
Inadequately tightened spark plugs can

cause overheating and damage the engine.
Tightening the spark plugs too hard can
damage the threads in the cylinder head.

8011-054

Measure the electrode gap

Checking the Safety System

The machine is equipped with a safety system that
prevents starting or driving under the following
conditions.

The engine can only be started when:

1. The mower deck is disengaged.

2. The steering controls are in the outer, locked
neutral position.

3. The driver is sitting in the driver’s seat.

4. The parking brake is on.

Make daily inspections to ensure that the safety
system works by attempting to start the engine
when one of the conditions is not met. Change the
conditions and try again.

If the machine starts when one of these conditions
is not met, turn the machine off and repair the safety
system before using the machine again.

Make sure the engine stops when the park brake is not
engaged and the operator leaves the seated position.

Check that the engine stops if the mower blades are
engaged and the driver temporarily moves off the
drivers seat.

Conditions for starting

IMPORTANT INFORMATION
In order to be able to drive, the driver

must sit in the seat and release the
parking brake before the steering controls
can be moved into the neutral position,
otherwise the engine will stop.

8011-527-1

English-40

MAINTENANCE

Checking the Engine’s Cooling Air
Intake

Check that the engine’s cooling air intake is free from
leaves, grass, and dirt.

If the cooling air intake is clogged, engine cooling
deteriorates, which can lead to engine damage.

The cooling air intakes rotates when the engine is
running. Mind your fi ngers.

Checking and Adjusting the Throttle
Cable

Check that the engine responds to throttle increases
and that a good engine speed is attained at full
throttle.

If doubts arise, contact the service workshop.
If adjustments are necessary, they can be made as

follows for the lower cable:

1. Loosen the clamping screw for the cable’s outer
casing and move the throttle to the full throttle
position.

2. Check that the throttle cable is mounted in the
correct hole in the lower lever, see illustration.

3. Push the throttle cable’s outer casing as far to the
right as possible and tighten the clamping screw.

8011-719

Check and clean the cooling air intake

2

1

8011-720

1. Throttle cable

Adjusting the throttle cable

Checking and Adjusting the Choke
Cable

If the engine produces black smoke or is diffi cult
to start, this can be because the choke cable is
incorrectly adjusted (upper cable).

If doubts arise, contact the service workshop.
If adjustments are necessary, they can be made as

follows:

1. Loosen the clamping screw for the cable’s outer
casing and push the choke control fully in.

2. Check that the choke cable is mounted in the
upper lever, see illustration. Push the choke cable’s
outer casing as far to the left as possible and
tighten the clamping screw.

2. Choke cable

Adjusting the choke cable

2

1

8011-720

English-41

MAINTENANCE

Checking the Engine’s Cooling Air Intake

Check that the engine’s cooling air intake is free from
leaves, grass, and dirt.

If the cooling air intake is clogged, engine cooling
deteriorates, which can lead to engine damage.

Checking and Adjusting the Throttle Cable

On Kohler engine the cables are mounted under the
air fi lter housing. The throttle cable on Kohler must be
mounted in the middle hole.

Check that the engine responds to throttle increases
and that a good engine speed is attained at full
throttle.

If doubts arise, contact the service workshop.
If adjustments are necessary, they can be made as

follows for the lower cable:

1. Loosen the clamping screw for the cable’s
outer casing and move the throttle to the full
throttle position.

2. Check that the throttle cable is mounted
in the correct hole in the lower lever, see
illustration.

3. Push the throttle cable’s outer casing as
far to the left as possible and tighten the
clamping screw.

Checking and Adjusting the Choke Cable

If the engine produces black smoke or is diffi cult
to start, this can be because the choke cable is
incorrectly adjusted (upper cable).

If doubts arise, contact the service workshop.
If adjustments are necessary, they can be made
as follows:

1. Loosen the clamping screw for the cable’s
outer casing and move the choke lever to the
full choke position.

2. Check that the choke cable is mounted in the
upper lever, see illustration. Push the choke
cable’s outer casing as far to the right as
possible and tighten the clamping screw.

Check and clean the cooling air intake

8011-625

English-42

MAINTENANCE

Replacing the Air Filter - Kohler Engine

These engines are equipped with a replaceable, high
density paper air cleaner element. Some engines are
also equipped with an oiled, foam precleaner which
surrounds the paper element. Two different capacity
air cleaner systems are available.

Check the air cleaner daily or before starting the
engine. Check for a buildup of dirt and debris around
the air cleaner system. Keep this area clean. Also
check for loose or damaged components. Replace all
bent or damaged air cleaner components.

IMPORTANT INFORMATION
Operating the engine with loose or

damaged air cleaner components could
allow unfi ltered air into the engine causing
premature wear and failure.

Servicing Precleaner:

If so equipped, wash and re-oil the precleaner every
25 hours of operation (more often under extremely
dusty or dirty conditions). Replace the precleaner

annually, or every 100 hours.

1. Open the door on the blower housing
to access the air cleaner element and
precleaner.

2. Unhook the latch and remove the precleaner
from the air cleaner element, or remove as
an assembly for servicing. Make sure the
base and the sealing area is clean before
reassembly is performed.

3. Wash the precleaner in warm water with
detergent. Rinse the precleaner thoroughly
until all traces of detergent are eliminated.
Squeeze out excess water (do not wring).
Allow the precleaner to air dry.

4. Saturate the precleaner with new engine oil.
Squeeze out all excess oil.

5. Reinstall the precleaner over the paper
element and secure with the latch.

6. Close and latch the door.

Service Paper Element:

Check the paper element every 50 hours of operation,
(more often under extremely dusty or dirty conditions).
Clean or replace the element as necessary. Replace
the air cleaner element annually, or every 100 hours.

1. Open the door on the blower housing to
access the air cleaner element.

2. Unhook the latch and remove the air cleaner
element and precleaner (if equipped).

3. Remove the precleaner (if so equipped) from
the paper element. Service the precleaner as
described in Precleaner Service.

4. Gently tap the paper element to dislodge
dirt. Do not wash the paper element or
use pressurized air, as this will damage the
element. Replace a dirty, bent, or damaged
element with a new one. Handle the new
element carefully; do not use if the sealing
surfaces are bent or damaged.

5. Clean the air cleaner base as required and
check condition.

6. Reinstall the precleaner (if equipped) over
the paper air cleaner element and install on
the base. Secure with the latch.

7. Close and latch the door.

English-43

MAINTENANCE

Air Filter Maintenance

If the engine seems weak or runs unevenly, the air
fi lter may be clogged. If running with a dirty air fi lter ,
the spark plugs can become fouled.

For this reason, it is important to replace the air fi lter
regularly (see the heading Maintenance Schedule for
the proper service interval).

WARNING!
The engine and the exhaust

system become very hot during
operation. Risk for burns if
touched.

Allow engine and exhaust system
to cool at least two (2) minutes.

IMPORTANT INFORMATION
Do not use compressed air to clean the air

fi lter.
Do not wash the paper fi lter.
Do not oil the paper fi lter.
Do not tap fi lter to clean this could cause

damage to the sealing.

Cleaning/replacing the air fi lter is carried out as
follows:

Dust cap

Check the dust cap every day by pressing the rubber
valve with two fi ngers to let out the dirt.

IMPORTANT INFORMATION
The end cover must be installed with

the rubber valve pointing downwards,
otherwise the rubber valve will not function.

8011-447

Pressing the rubber valve

Clean the dust cap by removing the end cover of the
air cleaner and clean inside.

English-44

Removing the end cover

8011-448

MAINTENANCE

Filter replacement

1. Remove the end cover.

2. Remove the main fi lter (outer fi lter) by pulling
it out by hand.

3. Remove the inner fi lter by pulling it out by
hand.

4. Clean inside of the fi lter housing. Wipe dry
only.

5. Install the inner fi lter with the open end fi rst.
Ensure that it enters its recess at the end of
the housing and push it in to the end.

6. Install the main fi lter with the open end fi rst.
Ensure that it enters its recess at the end of
the housing and push it in to the end.

IMPORTANT INFORMATION
The end cover must be installed with

the rubber valve pointing downwards,
otherwise the rubber valve will not
function.

Removing the main fi lter

8011-449

7. Turn the end cover with the rubber valve
pointing downwards and install it.

Air fi lter indicator (optional)

Change the main fi lter when the yellow piston is
hanging at the top of the cylinder. To reset the
indicator, push on the button (arrow) at the cylinder. A
number of pushes may be required. If it indicates soon
after a main fi lter replacement, change the inner fi lter .

Removing the inner fi lter

Air fi lter indicator

8011-450

8011-467

English-45

MAINTENANCE

Replacing the Fuel Filter

Replace the line-mounted fuel fi lter every 100 hours
(once per season) or more regularly if it is clogged.

Replace the fi lter as follows:

1. Move the hose clamps away from the fi lter. Use
fl at-nosed pliers.

2. Pull the fi lter loose from the hose ends.

3. Push the new fi lter into the hose ends. Position the
fi lter with the “FLOW” arrow pointing up toward the
fuel pump. If necessary, a soap solution can be
applied to the fi lter ends to ease mounting.

4. Move the hose clamps back toward the fi lter.

Checking the Fuel Pump’s Air Filter

Regularly check that the fuel pump’s air fi lter is free
from dirt.

Remove the screws and open the pump, no hoses
need be removed.

The fi lter can be cleaned with a brush if necessary.
Replace the fi lter on the console.

Checking Tire Pressures

All four tires shall have a pressure of 15 psi / 103 kPa
/1 bar.

Fuel fi lter

The fuel pump’s air fi lter

8011-468

8009-147

English-46

8011-564

Tire pressures

MAINTENANCE

Checking the Parking Brake

Visually check that no damage is found on the lever,
links, or switch belonging to the parking brake.
Perform a standstill test and check that there is
suffi cient braking action.

To adjust the parking brake, contact the Dixon service
workshop.

WARNING!
Faulty adjustment result in

reduced braking ability and can
cause an accident.

Checking the V-belts

Check every 100 hours of operation. Check for severe
cracking and large nicks.

NOTE: The belt will show some small cracks in normal
operation.

The belts are not adjustable. Replace belts if they
begin to slip from wear.

Deck belt

To replace deck belt

Deck belt removal.

• Park on a level surface. Apply park brake.

• Lower the deck into the lowest cutting position.

• Using a ratchet with a

idler bolt to relieve the tension on the belt.

9

/16" socket on the spring

• Remove foot plate

Remove screws from both the left and right belt

•

shields, and remove shields.

• Remove any dirt or grass that may have

accumulated around the cutter housings and entire
deck surface.

• Carefully roll the belt over the top of the cutter

housing pulleys.

• Remove the belt from around the electric clutch on

the engine shaft.

• The belt can now be removed.

The parking brake in the disengaged position

IMPORTANT INFORMATION
The machine must be absolutely standing

still when applying the parking brake.

Slackening the belt tensioner

8011-711

8011-622

English-47

MAINTENANCE

Deck belt installation

NOTE: For ease in installing the deck belt, refer to the
routing decal on the front edge of the deck.

• Wrap the deck belt around the electric clutch that

is located on the engine shaft.

• Push the rest of the belt through the IZT

(Integrated Zeroturn Transaxle) support and up
onto the deck.

• Starting on the right hand side of the deck, wrap

the belt around the large right side idler, right cutter
housing pulley, small center idler, center pulley, left
side pulley and then around the large left side idler.

• The belt will be loose at this point.

• Using a ratchet with a

idler bolt to relieve the tension on the belt.
See decal on the top of deck for belt routing
information.

• After installation is complete check the belt for

twists.

9

/16" socket on the spring

7

Belt routing, deck belt

1

2

3

6

5

4

8011-580

Deck belt installation for 60" decks

• Remove fl oor plate to gain access to the deck

Route the belt according to the illustration.
Route belt around clutch and all pulleys according

to diagram except for spindle pulley #4.

Using a ½" breaker bar and short ½” extension,

insert extension into spring-loaded idler at the
square hole in the idler arm #3.

Rotate spring-loaded idler #3 clockwise to relieve

tension and lengthen belt until belt can be slipped
over remaining pulley #4. Belt installation is
complete.

Slackening the belt tensioner

7

1. Clutch pulley

2. Spring

3. Spring-loaded idler pulley

4. Left spindle

5. Center spindle

6. Center fi xed idler pulley

7. Right spindle

6

5

Belt routing, deck belt - 60” decks

8011-622

1

2

4

3

8011-580

English-48

MAINTENANCE

Pump belt

Check belt every 100 hours for excessive wear.
To replace belt. Relieve tension on the deck belt and

remove deck belt from clutch. See “ Deck belt” section.
Loosen bolt on the clutch tie down and rotate out of
the way.

Using a ½" drive ratchet inserted into the square hole
in the pump idler arm relieve the tension on the pump
belt and remove belt.

To reinstall belt: Swing pump idler pulley toward
engine to route belt around it. Then route belt around
the pulley for left pump fi rst (right hand pulley in the
illustration).

Reinstall idler spring and use the ratchet to rotate idler
so the belt may be installed all the way around the last
pulley.

8011-623

Slackening the belt tension

Belt routing, hydraulic pumps

8011-624

English-49

MAINTENANCE

Checking the Blades

In order to attain the best mowing effect, it is important
that the blades are well sharpened and not damaged.

WARNING!
Blades are sharp. Protect your

hands with gloves and/or wrap
blades with a heavy cloth when
handling.

Bent or cracked blades or blades with large nicks
should be replaced.

Damaged blades should be replaced when hitting
obstacles that result in a breakdown. Let the service
workshop decide whether the blade can be repaired/
ground or must be replaced.

Balance the blades after sharpening.
Check the blade mounts.

8011-604

Check the blades

IMPORTANT INFORMATION
The sharpening of blades should be

carried out by an authorized service
workshop.

English-50

MAINTENANCE

Blade replacement

WARNING!
Blades are sharp. Protect your

hands with gloves and/or wrap
blades with a heavy cloth when
handling.

• Remove blade bolt by turning counterclockwise.

IMPORTANT INFORMATION
To ensure proper assembly, center hole

in blade must align with star on cutter
housing.

• Install new or re-sharpened blade with stamped

“GRASS SIDE” facing towards ground/grass
(down) or “THIS SIDE UP” facing deck and cutter
housing.

• Install and tighten blade bolt securely.

• Torque blade bolt to 45-55 ft/lbs (60-75 Nm).

1

3

1. Blade

2. Debris shield

3. Blade bolt (special)

4. Cutter housing

Blade attachment

4

2

IMPORTANT INFORMATION
Special blade bolt is heat treated.
Replace with a Dixon bolt if required.
Do not use lower grade hardware than

specifi ed.

English-51

MAINTENANCE

Adjusting the Mower Deck

WARNING!
Before performing any service or adjustment checklist:

1. Engage the parking brake.

2. Place the Blade switch in the disengaged position.

3. Turn ignition switch to “OFF” position and remove the key.

4. Make sure the blades and all moving parts have completely stopped.

5. Disconnect the spark plug wire from all spark plugs and place the wire where
it cannot come in contact with the plug.

Leveling

1. Position the mower on a level, preferably concrete,
surface.

2. Check the pressure in all four tires. See “Technical
Data”.

3. Rotate blades to align front to back.

4. Set the cutting height to 4".

5. Measure front blade tip, should be 4" from ground,
if not turn locknut on top of front eyebolt till
measurement is achieved. Check blade tip at front
on opposite front blade. Adjust locknut on front
eyebolt as necessary.

6. Check rear blade measurement, should be
4¼" from ground, if not turn locknut on top of
rear eyebolt to achieve measurement. Repeat
procedure on opposite side.

WARNING!
Blades are sharp. Protect your

hands with gloves and/or wrap
blades with a heavy cloth when
handling.

2

3

Adjusting Cutting Height

1. Raise and secure the deck height lever to the
transport position (6”).

2. Position blade tip so it is straight forward.

3. Measure from the cutting edge of the blades to
a fl at level surface. The distance should be 6”
(150 mm).

4. Drop and secure the lever at (for example) the 2”
cutting height. Measure as above. The distance
should be 2” (50 mm).

English-52

4

1

8011-601-1

1. Front eyebolt

2. Front locknut

3. Rear locknut

4. Rear eyebolt

Leveling the mower deck

MAINTENANCE

To adjust anti-scalp rollers

Anti-scalp rollers are properly adjusted when they are
just slightly off of the ground when the deck is at the
desired cutting height in the operating position. Anti­scalp rollers then keep the deck in the proper position
to help prevent scalping in most terrain conditions.

IMPORTANT INFORMATION
Adjust Anti-scalp rollers with the mower

on a fl at level surface.

The anti-scalp rollers can be set in three positions:

• Upper position 1½ to 3" (38 to 76 mm) grass.

• Middle position 3" to 4½" (76 to 114 mm) grass.

• Lower position 4½" to 6" (114 to 152 mm) grass.

The rollers should be approximately ¼" (6.5 mm) from
ground. Do not adjust the rollers to support the deck.

IMPORTANT INFORMATION
The anti-scalp rollers must not be used

for gauge wheels or the roller and deck
may be damaged.

Engine oil cooler

Kohler engine only.

1. Clean the outside of fi ns with a brush.

2. Remove the two screws holding the cooler unit to
the blower housing.

3. Tilt the cooler downward.

4. Clean the inside of the cooler with a brush or with
compressed air.

5. Reinstall the oil cooler to the blower housing.

CZ-9

Anti-scalp roller

8011-472

Engine oil cooler

English-53

MAINTENANCE

Cleaning and Washing

Regular cleaning and washing, especially under the
mower deck, will increase the machine’s life-span.
Make it a habit to clean the machine directly after use
(after it is cooled), before the dirt sticks.

Do not spray water on the top of the mower deck. Use
compressed air to clean the top side of mower deck.
Regularly clean deck and underside of the deck with
normal water pressure. Do not use a high pressure
washer or steam cleaner. Avoid spraying engine and
electrical components with water

Use protective glasses when
cleaning and washing.

Do not rinse hot surfaces with cold water. Let unit cool
before washing.

8050-092

Cleaning

Caster Wheels

Check every 200 hours. Check that wheels rotates
freely. If wheels do not rotate freely take the unit to
your dealer for service.

IMPORTANT INFORMATION
DO NOT add any type of tire liner or foam

fi ll material to the tires. Excessive loads
created by foam fi lled tires will cause
premature failures.

Only use O.E.M. specifi ed tires.

Foam fi lled tires or solid tires will void the warranty.

Removal and installation of caster wheel

Remove nut and caster bolt.
Pull the wheel out of the fork and take care of the

sleeve.
Install in reverse order. Tighten caster bolt.

Caster wheels

8011-619

Hardware

Check daily. Inspect the entire machine for loose or
missing hardware.

English-54

Lubrication

Lubrication Schedule

LUBRICATION

5

6

9

8

8

3

10

3

3

12/12 Every year
1/52 Every Week
1/365 Every day

*Change hydraulic (transmission) fi lters.

Lubricate with grease gun

Oil change

Filter change

Lubricate with oil can
Level check

General

Remove the ignition key to prevent unintentional movements during lubrication.
When lubricating with an oil can, it must be fi lled with engine oil.
When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulphide grease.
For daily use, the machine should be lubricated twice weekly.
Wipe away excess grease after lubrication.

8011-672-2

It is important to avoid getting lubricant on the belts or the drive surfaces on the belt pulleys. Should this happen,
attempt to clean them with spirits. If the belt continues to slip after cleaning, it must be replaced. Gasoline or other

petroleum products must not be used to clean belts.

English-55

LUBRICATION

Lubricating the Cables

If possible, grease both ends of the cables and move the controls to end stop positions when lubricating. Refi t the
rubber covers on the cables after lubrication. Cables with sheaths will bind if they are not lubricated regularly. If a
cable binds, it can disrupt operation.

If a cable binds, remove the cable and hang it vertically. Lubricate it with light engine oil until the oil begins to
escape from the bottom.

Tip: Fill a small plastic bag with oil and tape it so that it seals against the sheath and allow the cable to hang
vertically from the bag overnight. If you do not succeed in lubricating the cable, it must be replaced.

Shaft Bushings and Linkage

Lubricate the bearing of the shafts and linkage for
brake system and steering with oil spray or oil can.

Lubricating in Accordance with the
Lubrication Schedule

1. Hydraulic System, Oil Level

The hydraulic oil and fi lter must be replaced every 300
hours, and at least once a year. Contact an authorized
service workshop.

Check the oil level in the hydraulic tank daily. The level
shall be about ¾"-1" (19 - 25 mm) below the top of the
tank.

Check connections, hoses, and tubes for damage or
leaks. Replace or repair if doubtful.

Changing Oil and Filters

Oil and fi lter changes should be carried out by
an authorized service workshop due to the risk of
impurities enter the system.

2. Driver’s Seat

Tip the seat.
Lubricate the front hinges using an oil can.
Lubricate the lengthways adjustment mechanism with

the oil can.
Lubricate the lengthways adjustment runners with the

oil can.

Checking the hydraulic oil

WARNING!
If a leak is suspected, use a

piece of cardboard or wood, NOT
your hands, to check for leaks.
Escaping hydraulic oil under
pressure can have suffi cient force
to penetrate the skin, causing
serious injury.

If injured by escaping fl uid,
see a doctor at once. Serious
infection or reaction can develop
if proper medical treatment is not
administered immediately.

8011-565

IMPORTANT INFORMATION
Use minimal lubrication and remove

excess lubricant so that is does not come
into contact with belts or belt pulley drive
surfaces.

English-56

8011-571

Lubricating the lengthways adjuster under the seat

LUBRICATION

3. Engine Oil, Kohler Engine

Changing the Engine Oil

Change oil after every 100 hours of operation (more
frequently under severe conditions). Refi ll with service
class SG, SH, SJ or higher oil as specifi ed in the
Viscosity Grades table.

Change the oil while the engine is still warm. The oil
will fl ow more freely and carry away more impurities.
Make sure the engine is level when fi lling, checking or
changing the oil.

Change the oil as follows:

1. To keep dirt, debris, etc., out of the engine,
clean the area around the oil fi ll cap/dipstick
before removing it.

2. Remove the oil drain plug and the oil fi ll cap/
dipstick. Be sure to allow ample time for
complete drainage.

3. Reinstall the drain plug. Make sure it is
tightened to 10 ft. lb. (13.6 Nm) torque.

4. Fill the crankcase, with new oil of the proper
type, to the “FULL” mark on the dipstick. Refer
to the section on Oil Type. Always check the
level with the dipstick before adding more oil.

5. Reinstall the oil fi ll cap/dipstick and tighten
securely.

IMPORTANT INFORMATION
Used engine oil is a health hazard and

must not be disposed of on the ground or
in nature; it should always be disposed
of at a workshop or appropriate disposal
location.

Avoid skin contact; wash with soap and
water in case of spills.

WARNING!
Engine oil can be very hot if it is

drained directly after stopping
the engine. Allow the engine to
cool to a safe temperature fi rst.

IMPORTANT INFORMATION
To prevent extensive engine wear or

damage, always maintain the proper oil
level in the crankcase. Never operate the
engine with the oil level below the “ADD”
mark or over the “FULL” mark on the
dipstick.

6. Start the engine. Run it for a few seconds and
recheck the oil level.

English-57

LUBRICATION

Checking the Oil Level

The importance of checking and maintaining
the proper oil level in the crankcase cannot be
overemphasized.

Check oil before each use as follows:

1. Make sure the engine is stopped, level, and
cool so the oil has had time to drain into the oil
pan.

2. To keep dirt, debris, etc., out of the engine,
clean the area around the dipstick before
removing it.

3. Unthread and remove the dipstick; wipe oil off.
Reinsert the dipstick into the tube and rest the
cap on the tube. Do not thread the cap onto
the tube.

4. Pull the dipstick out and check the oil level.
The oil level should be up to, but not over, the
“FULL” mark on the dipstick.

5. If the level is low, add oil of the proper type, up
to the “FULL” mark on the dipstick. Refer to Oil
Type, page . Always check the level with the
dipstick before adding more oil.

IMPORTANT INFORMATION
To prevent extensive engine wear or

damage, always maintain the proper oil
level in the crankcase. Never operate the
engine with the oil level below the “ADD”
mark or over the “FULL” mark on the
dipstick.

Oil dipstick

Level marking

8011-471

8009-159

English-58

LUBRICATION

Oil Recommendations

Using the proper type and weight of oil in the
crankcase is extremely important. So is checking oil
daily and changing oil regularly. Failure to use the
correct oil, or using dirty oil, causes premature engine
wear and failure.

Oil Type

Use high quality detergent oil of API (American
Petroleum Institute) service class SG, SH, SJ
or higher. Select the viscosity based on the air
temperature at the time of operation.

10W-30

**

5W-20, 5W-30

F

-20

0

*

Kohler Command

20 32 80

40 100

60

IMPORTANT INFORMATION
Using other than service class SG, SH,

SJ or higher oil or extending oil change
intervals longer than recommended can
cause engine damage.

IMPORTANT INFORMATION
Synthetic oils meeting the listed

classifi cations may be used with oil
changes performed at the recommended
intervals. However to allow piston rings
to properly seat, a new or rebuilt engine
should be operated for at least 50 hours
using standard petroleum based oil
before switching to synthetic oil.

C4

Temperature range expected before next oil change

* Use of synthetic oil having 5W-20 or 5W-30 rating is
acceptable, up to 40 oF (+4 oC).

** Synthetic oils will provide better starting in extreme
cold below -10

Viscosity grades table

-20-30

0-10

o

F (-23 oC).

10

3020

0

8011-766

A logo or symbol on oil containers identifi es the API
service class and SAE viscosity grade.

English-59

LUBRICATION

4. Throttle and Choke Cables, Lever Bearings

Lubricate the cable ends by the carburetor with the oil
can. Move the controls to the end points and lubricate
again.

The throttle cable is also lubricated by the control
when the control console is removed.

On Kohler engine the cables are placed under the air
fi lter housing.

5. Front Wheel Mount

Lubricate with a grease gun, one zerk for each wheel
mount, until the grease is forced out.

Use only good quality molybdenum disulphide grease.
Grease from well-known brand names (petrochemical

companies, etc.) usually maintains a good quality.

6. Front Wheel Bearings

Lubricate with a grease gun, one zerk for each set of
wheel bearings, until the grease is forced out.

Use only good quality molybdenum disulphide grease.
Grease from well-known brand names (petrochemical

companies, etc.) usually maintains a good quality.

8011-573-

Lubricating the front wheels

7. Deck belt pulleys

Lubricate with a grease gun two strokes.

8. Mower Deck Height Adjuster

Lubricate using a grease gun, one zerk, until the
grease squeezes out.

Use only good quality molybdenum disulphide grease.
Grease from well-known brand names (petrochemical

companies, etc.) usually maintains a good quality.

8011-461

Deck belt pulley

English-60

8011-574

Lubricating the cutting height adjuster

LUBRICATION

9. Belt Adjuster, Mower Deck

Remove the foot plate (two screws) and lubricate with
a grease gun, one zerk, until grease is forced out.

Use only good quality molybdenum disulphide grease.

Grease from well-known brand names (petrochemical
companies, etc.) usually maintains a good quality.

IMPORTANT INFORMATION
Use minimal lubrication and remove

excess lubricant so that it does not come
into contact with belts or belt pulley drive
surfaces.

8011-573

The belt adjuster grease nipple

10. Steering Control Shafts

Tip the driver’s seat.

Lubricate with a grease gun, one zerk for each
steering control shaft, until the grease is forced out.

Use only good quality molybdenum disulphide grease.

Grease from well-known brand names (petrochemical
companies, etc.) usually maintains a good quality.

11. Mower Deck Struts

Lubricate with a grease gun, one zerk for each strut,
until the grease is forced out.

Use only good quality molybdenum disulphide grease.
Grease from well-known brand names (petrochemical

companies, etc.) usually maintains a good quality.

8011-578

Lubricating the steering control shafts

Lubricating struts

8011-577-1

English-61

LUBRICATION

12. Changing the Oil Filter

1. Drain the engine oil in accordance with the
work description under the heading Engine
Oil/Change Engine Oil.

2. Remove the oil fi lter. If necessary, use a fi lter
remover.

3. Wipe new, clean engine oil onto the seal for
the new fi lter.

4. Mount the fi lter by hand with + ¾ turn.

5. Run the engine warm, then check that there
are no leaks around the oil fi lter seal.

6. Check the oil level in the engine, top up
if necessary. The oil fi lter holds 0.2 qt.
(0.2 liters) of oil.

8011-745

Changing the oil fi lter Kohler

English-62

TROUBLE SHOOTING GUIDE

Trouble Shooting Guide

Problem

Cause

The engine will not start.

The starter does not turn the engine over.

• The blade switch is engaged.

• The steering controls are not locked in the neutral

position.

• The driver is not sitting in the driver’s seat.

• The parking brake is not activated.

• The battery is dead.

• Contamination in the carburetor or fuel line.

• The fuel supply is closed or the shut-off valve for

the fuel tank is in the wrong position.

• Clogged fuel fi lter or fuel line.

• Dead battery.

• Poor contacts on the battery terminal cable

connections.

• Fuse blown.

• Ignition system faulty.

• Fault in the starter safety circuit. See Checking the

Safety System in the “Maintenance Section,”

The engine runs rough.

• Faulty carburetor.

• The choke control is pulled out with warm engine.

• Defective valves.

• Defective piston, cylinder, piston ring, or

cylinder head seal.

• The cylinder head bolts are loose.

• Clogged fuel fi lter or jet.

• Clogged ventilation valve on the fuel cap.

• Fuel tank nearly empty.

• Defective spark plugs.

• The spark plugs are loose.

• Defective ignition cable.

• Defective spark plug electrode.

• Defective spark plug connection.

• Rich fuel mixture or fuel-air mixture.

• Wrong fuel type.

• Water in the fuel.

• Clogged air fi lter.

• Air trapped in hydraulic system.

English-63

TROUBLE SHOOTING GUIDE

The engine seems weak.

The engine overheats.

Battery not charging.

The machine moves slowly, unevenly, or not at all.

• Clogged air fi lter.

• Defective spark plugs.

• Carburetor incorrectly adjusted.

• Air trapped in hydraulic system.

• Clogged air intake or cooling fi ns.

• Engine overloaded.

• Poor ventilation around engine.

• Defective engine speed regulator.

• Soot in the combustion chamber.

• Too little or no oil in the engine.

• Defective spark plugs.

• Pre-ignition incorrect.

• Air trapped in hydraulic system.

• Poor contact with battery terminal cable

connectors.

• Parking brake on.

Mower deck not engaging.

Transaxle leaks oil.

• Bypass valve on pump open.

• Drive belt for the transmission gears slack or has

come off.

• Air trapped in hydraulic system.

• Drive belt for the mower deck has come loose.

• Contact for the electromagnetic coupling has

loosened.

• The blade switch is faulty or has come loose,

from the cable contact.

• The fuse has blown.

• Damaged seals, housing, or gaskets.

• Air trapped in hydraulic system.

English-64

TROUBLE SHOOTING GUIDE

Uneven mowing results.

The machine vibrates.

• Different air pressure in the tires on the left and

right sides.

• Bent blades.

• The suspension for the mower deck is uneven.

• The chain fi xture has come loose.

• The blades are blunt.

• Driving speed too high.

• The grass is too long.

• Grass collected under the mower deck.

• The blades are loose.

• The blades are incorrectly balanced.

• The engine is loose.

English-65

STORAGE

Storage

Winter Storage

At the end of the mowing season, the machine should
be readied for storage (or if it will not be in use for
longer than 30 days). Fuel allowed to stand for long
periods of time (30 days or more) can leave sticky
residues that can plug the carburetor and disrupt
engine function.

Fuel stabilizers are an acceptable option as regards to
the sticky residues that can occur during storage.

Add stabilizer to the fuel in the tank or in the storage
container. Always use the mixing ratios specifi ed by
the manufacturer of the stabilizer. Run the engine for
at least 10 minutes after adding the stabilizer so that it
reaches the carburetor. Do not empty the fuel tank and
the carburetor if you have added stabilizer

WARNING!
Never store an engine with

fuel in the tank indoors or in
poorly ventilated spaces where
fuel vapor can come in contact
with open fl ames, sparks, or a
pilot light such as in a boiler,
hot water tank, clothes drier,
etc. Handle the fuel with care.
It is very fl ammable and can
cause serious personal injury
and property damage. Drain the
fuel into an approved container
outdoors and far away from
open fl ame. Never use gasoline
for cleaning. Use a degreaser
and warm water instead.

To ready the machine for storage, follow these steps:

1. Thoroughly clean the machine, especially under
the mower deck. Touch up damage to the paint
and spray a thin layer of oil on the underside of the
mower deck to avoid corrosion.

2. Inspect the machine for worn or damaged parts
and tighten any nuts or screws that may have
become loose.

3. Change the engine oil; dispose of properly.

4. Empty the fuel tanks or add a fuel stabilizer. Start
the engine and allow it to run until the carburetor
is drained of fuel or the stabilizer has reached the
carburetor.

5. Remove the spark plug and pour about a
tablespoon of engine oil into the cylinder. Turn over
the engine so that the oil is evenly distributed and
then refi t the spark plug.

6. Lubricate all grease zerks, joints, and axles.

7. Remove the battery. Clean, charge, and store the
battery in a cool place, but protect it from direct
cold.

8. Store the machine in a clean, dry place and cover
it for extra protection.

Service

When ordering spare parts, please specify the
purchase year, model, type, and serial number.

Always use genuine Dixon spare parts.
An annual check-up at an authorized service workshop

is a good way to ensure that your machine performs its
best the following season.

English-66

WIRING DIAGRAM

English-67

Technical Data

TECHNICAL DATA

Grizzly / 968999588

Engine

Manufacturer Kohler Kohler
Type CV740S CV740S
Power 27hp 27 hp
Lubrication Pressure with oil fi lter Pressure with oil fi lter
Oil capacity excl fi lter 1.6 qt / 1.5 liters 1.6 qt / 1.5 liters
Oil capacity incl fi lter 2.0 qt / 2.2 liters 2.0 qt / 2.2 liters
Engine oil, Synthetic SAE 5W30, 10W30 SAE 5W30, 10W30

Engine oil, Mineral Class SAE 30, (winter 10W30) SAE 30, (winter 10W30)
API, SF, SJ, SH, SG API, SF, SJ, SH, SG

Fuel Min 87 octane unleaded Min 87 octane unleaded
(Max methanol 5%, max eth- (Max methanol 5%, max

anol 10%, Max MTBE 15%) ethanol 10%, Max MTBE 15%)

Fuel tank capacity 11.4 gallon / 43 liters 11.4 gallon / 43 liters

Grizzly / 968999590

Spark plugs/gap Champion RX12YC Champion RX12YC
.030" / 0.75 mm .030" / 0.75 mm

Cooling Air cooling Air cooling
Air fi lter Standard Standard
Alternator 12V 16A 12V 16A
Starter Electric 12V Electric 12V

Transmission

Transmission Dual pumps, wheel drive motors Dual pumps, wheel drive motors
Speed and direction controls Duel levers, foam gripped Duel levers, foam gripped
Speed forward 0-10 mph / 16.1 km/h 0-10 mph / 16.1 km/h
Speed reverse 0-5 mph / 0-8 km/h 0-5 mph / 0-8 km/h
Brakes Hydrostatic/disk brake Hydrostatic/disk brake
Front caster tires, smooth tread 13x6.5-6 Tubeless 13x6.5-6 Tubeless
Rear tires, Turf pneumatic 24 X 12.00-12 tubeless 24 X 12.00-12 tubeless
Tire pressure, front and rear 15 PSI / 103 kPa / 1 bar 15 PSI / 103 kPa / 1 bar

English-68

TECHNICAL DATA

Grizzly / 968999588

Equipment

Cutting width 52" 60"
Cutting height 1.5" - 4.5" / 38mm - 114mm 1.5" - 4.5" / 38mm - 114mm
Uncut circle 0 0
Number of blades 3 3
Blade length 18" / 457 mm 20" / 508mm
Nose rollers Yes Yes
Seat Standard Standard
Hinged armrests Yes Yes
Hour meter Standard Standard
Blade engagement Electric clutch Electric clutch
Deck construction 11 gauge w/10 gauge skirts 11 gauge w/10 gauge skirts

Productivity

Grizzly / 968999590

Productivity 4.1 acres/h/16605m2h 5.1 acres/h/20655m2h
Overall dimensions
Weight 1140 lbs (517 kg) 1150 (522 kg)
Base machine length 84” (214 cm) 84" (214 cm)
Base machine width 50" (127 cm) 54" (137 cm)
Base machine height 48" (122 cm) 48" (122 cm)
Overall width, chute up 62" (157 cm) 69" (175 cm)
Overall width, chute down 68" (173 cm) 75" (91 cm)

English-69

Technical Data

TECHNICAL DATA

Grizzly / 968999592

Engine

Manufacturer Kohler Kohler
Type CV747S CV740S
Power 30 hp 27 hp
Lubrication Pressure with oil fi lter Pressure with oil fi lter
Oil capacity excl fi lter 1.6 qt / 1.5 liters 1.6 qt / 1.5 liters
Oil capacity incl fi lter 2.0 qt / 2.2 liters 2.0 qt / 2.2 liters
Engine oil, Synthetic SAE 5W30, 10W30 SAE 5W30, 10W30

Engine oil, Mineral Class SAE 30, (winter 10w30) SAE 30, (winter 10W30)
API, SF, SJ, SH, SG API, SF, SJ, SH, SG

Fuel Min 87 octane unleaded Min 87 octane unleaded
(Max methanol 5%, max (Max methanol 5%, max

ethanol 10%, Max MTBE 15%) ethanol 10%, Max MTBE 15%)

Fuel tank capacity 11.4 gallon / 43 liters 11.4 gallon / 43 liters

Grizzly / 968999626

Spark plugs/gap Champion RX12YC Champion RX12YC
.030" / 0.75 mm .030" / 0.75 mm

Cooling Air cooling Air cooling
Air fi lter Standard Standard
Alternator 12V 16A 12V 16A
Starter Electric 12V Electric 12V

Transmission

Transmission Dual pumps, wheel drive motors Dual pumps, wheel drive motors
Speed and direction controls Duel levers, foam gripped Duel levers, foam gripped
Speed forward 0-10 mph / 16.1 km/h 0-10 mph / 16.1 km/h
Speed reverse 0-5 mph / 0-8 km/h 0-5 mph / 0-8 km/h
Brakes Hydrostatic/disk brake Hydrostatic/disk brake
Front caster tires, smooth tread 13x6.5-6 Tubeless 13x6.5-6 Tubeless
Rear tires, Turf pneumatic 24 X 12.00-12 tubeless 24 X 12.00-12 tubeless
Tire pressure, front and rear 15 PSI / 103 kPa / 1 bar 15 PSI / 103 kPa / 1 bar

English-70

TECHNICAL DATA

Grizzly / 968999592

Equipment

Cutting width 72" 60"
Cutting height 1.5" - 4.5" / 38mm - 114mm 1.5" - 4.5" / 38mm - 114mm
Uncut circle 0 0
Number of blades 3 3
Blade length 24.5" / 622mm 20" / 508mm
Nose rollers Yes Yes
Michigan Seat Standard Standard
Hinged armrests Yes Yes
Hour meter Standard Standard
Blade engagement Electric clutch Electric clutch
Deck construction 11 gauge w/10 gauge skirts 11 gauge w/10 gauge skirts

Productivity

Grizzly / 968999626

Productivity 6 acres/h/24300m2h 5.1 acres/h/20655m2h
Overall dimensions
Weight 1200 lbs (544 kg) 1150 (522 kg)
Base machine length 86" (218 cm) 84" (214 cm)
Base machine width 52" (132 cm) 54" (137 cm)
Base machine height 48" (122 cm) 48" (122 cm)
Overall width, chute up 81" (206 cm) 69" (175 cm)
Overall width, chute down 88" (224 cm) 75" (91 cm)

English-71

Technical Data

TECHNICAL DATA

Grizzly / 968999628

Engine

Manufacturer Kohler Kohler
Type CV747S CV747S
Power 30 hp 30 hp
Lubrication Pressure with oil fi lter Pressure with oil fi lter
Oil capacity excl fi lter 1.6 qt / 1.5 liters 1.6 qt / 1.5 liters
Oil capacity incl fi lter 2.0 qt / 2.2 liters 2.0 qt / 2.2 liters
Engine oil, Synthetic SAE 5W30, 10W30 SAE 5W30, 10W30

Engine oil, Mineral Class SAE 30, (winter 10w30) SAE 30, (winter 10w30)
API, SF, SJ, SH, SG API, SF, SJ, SH, SG

Fuel Min 87 octane Min 87 octane
unleaded (Max ethyl unleaded (Max ethyl
alcohol 10%, max MTBE 15%) alcohol 10%, max MTBE 15%)

Fuel tank capacity 11.4 gallon / 43 liters 11.4 gallon / 43 liters

Grizzly / 968999591

Spark plugs/gap Champion RX12YC Champion RX12YC
.030" / 0.75 mm .030" / 0.75 mm

Cooling Air cooling Air cooling
Air fi lter Standard Standard
Alternator 12V 16A 12V 16A
Starter Electric 12V Electric 12V

Transmission

Transmission Dual pumps, wheel drive motors Dual pumps, wheel drive motors
Speed and direction controls Duel levers, foam gripped Duel levers, foam gripped
Speed forward 0-10 mph / 16.1 km/h 0-10 mph / 16.1 km/h
Speed reverse 0-5 mph / 0-8 km/h 0-5 mph / 0-8 km/h
Brakes Hydrostatic/disk brake Hydrostatic/disk brake
Front caster tires, smooth tread 13x6.5-6 Tubeless 13x6.5-6 Tubeless
Rear tires, Turf pneumatic 24 X 12.00-12 tubeless 24 X 12.00-12 tubeless
Tire pressure, front and rear 15 PSI / 103 kPa / 1 bar 15 PSI / 103 kPa / 1 bar

English-72

TECHNICAL DATA

Grizzly / 968999628

Equipment

Cutting width 72" / 1829mm 60" / 1524mm
Cutting height 1.5" - 4.5" / 38mm - 114mm 1.5" - 4.5" / 38mm - 114mm
Uncut circle 0 0
Number of blades 3 3
Blade length 24.5" / 622mm 20" / 508mm
Nose rollers Yes Yes
Michigan Seat Standard Standard
Hinged armrests Yes Yes
Hour meter Standard Standard
Blade engagement Electric clutch Electric clutch
Deck construction 11 gauge w/10 gauge skirts 11 gauge w/10 gauge skirts
Productivity

Grizzly / 968999591

Productivity 6 acres/h/24300m2h 5.1 acres/h/20655m2h
Overall dimensions
Weight 1200 lbs (544 kg) 1150 (522 kg)
Base machine length 86" (218 cm) 84" (214 cm)
Base machine width 52" (132 cm) 54" (137 cm)
Base machine height 48" (122 cm) 48" (122 cm)
Overall width, chute up 81" (206 cm) 69" (175 cm)
Overall width, chute down 88" (224 cm) 75" (91 cm)

English-73

TECHNICAL DATA

Technical Data

Grizzly / 968999627

Engine

Manufacturer Kohler
Type CV747S
Power 30 hp
Lubrication Pressure with oil fi lter
Oil capacity excl fi lter 1.6 qt / 1.5 liters
Oil capacity incl fi lter 2.0 qt / 2.2 liters
Engine oil, Synthetic SAE 5W30, 10W30

Engine oil, Mineral Class SAE 30, (winter 10w30)
API, SF, SJ, SH, SG

Fuel Min 87 octane
unleaded (Max ethyl
alcohol 10%, max MTBE 15%)

Fuel tank capacity 11.4 gallon / 43 liters
Spark plugs/gap Champion RX12YC

.030" / 0.75 mm
Cooling Air cooling
Air fi lter Standard
Alternator 12V 16A
Starter Electric 12V

Transmission

Transmission Dual pumps, wheel drive motors
Speed and direction controls Duel levers, foam gripped
Speed forward 0-10 mph / 16.1 km/h
Speed reverse 0-5 mph / 0-8 km/h
Brakes Hydrostatic/disk brake
Front caster tires, smooth tread 13x6.5-6 Tubeless
Rear tires, Turf pneumatic 24 X 12.00-12 tubeless
Tire pressure, front and rear 15 PSI / 103 kPa / 1 bar

English-74

TECHNICAL DATA

Grizzly / 968999627

Equipment

Cutting width 60" / 1524mm
Cutting height 1.5" - 4.5" / 38mm - 114mm
Uncut circle 0
Number of blades 3
Blade length 20" / 508mm
Nose rollers Yes
Michigan Seat Standard
Hinged armrests Yes
Hour meter Standard
Blade engagement Electric clutch
Deck construction 11 gauge w/10 gauge skirts
Productivity
Productivity 5.1 acres/h/20655m2h
Overall dimensions
Weight 1150 (522 kg)
Base machine length 84" (214 cm)
Base machine width 54" (137 cm)
Base machine height 48" (122 cm)
Overall width, chute up 69" (175 cm)
Overall width, chute down 75" (91 cm)

English-75

TECHNICAL DATA

Accessories

BioClip attachment (Mulch kit)
Collection system

Torque Specifi cations

·Engine crankshaft bolt 50 ft/lb (67 Nm)

·Deck pulley bolts 45 ft/lb (61 Nm)

·Lug nuts 75 ft/lb (100 Nm)

·Blade bolt 45-55 ft/lb (60-75 Nm)

·Standard ¼" fasteners 9 ft/lb (12 Nm)

·Standard 5/16" fasteners 18 ft/lb (25 Nm)

·Standard 3/8" fasteners 33 ft/lb (44 Nm)

·Standard 7/16" fasteners 52 ft/lb (70 Nm)

·Standard ½" fasteners 80 ft/lb (110 Nm)
When this product is worn out and no longer used, it should be returned to the reseller or other party for recycling.

In order to implement improvements, specifi cations and designs can be altered without prior
notifi cation.

Note that no legal demands can be placed based on the information contained in these
instructions.

Use only original parts for repairs. The use of other parts voids the warranty.
Do not modify or install non-standard equipment to the unit without consent from the

manufacturer. Modifi cations to the unit may cause unsafe operations or damage the unit.

English-76

CONFORMITY CERTIFICATES

Conformity Certifi cates

USA requirements

Labels are placed on the engine and/or in the engine compartment stating that the machine will fulfi ll the
requirements. This is also applicable to special requirements for any of the states, (California emission rules etc.).
Do not remove any of these labels. Certifi cates can also be supplied with the machine at delivery or written in the
Engine manual. Take care of them as they are valuable documents.

CE requirements

Vibration data corresponding to Directive 2002/44/EC is given in the Technical Data Section.
The Declaration of Conformity is included in the literature packet.

English-77

SERVICE JOURNAL

Service Journal

Action

Delivery Service

1. Charge the battery.

2. Adjust the tire pressure of all wheels to 15 PSI (1 bar).

3. Mount the steering controls in the normal position.

4. Connect the contact box to the cable for the seat’s
safety switch.

5. Check that the right amount of oil is in the engine.

6. Adjust the position of the steering controls.

7. Fill with fuel and open the fuel shut off valve.

8. Start the engine.

9. Check that there is drive to both wheels.

10. Check the mower deck adjustment.

Date, mtr reading, stamp, sign

11. Check:
The safety switch for the parking brake.
The safety switch for the mower deck.
The safety switch in the seat.
The safety switch in the steering controls.
Parking brake functionality.
Driving forward.
Driving backward.
Engaging the blades.

12. Check the idle speed

13. Check the engine high idle speed

14. Inform the customer about:
The need and advantages of following the service schedule.
The need and advantages of leaving the machine

for service every 300 hours.
The effects of service and maintaining a service journal on

the machine’s resale value.

Delivery service has been carried out.
No remaining notes.
Certifi ed:

Application areas for Mulching.

15. Fill in the sales papers, etc.

English-78

After the First 5-8 Hours

1. Change engine oil.

SERVICE JOURNAL

English-79

SERVICE JOURNAL

Action Date, mtr reading, stamp, sign

25-Hour Service

1. Check the fuel pump’s air fi lter.

2. Sharpen/Replace mower blades if required.

3. Check the tire pressures.

4. Check battery with cables.

5. Lubricate according to lubrication chart.

6. Check/clean the engine’s cooling air intake.

7. Clean the air cleaner’s pre-fi lter (foam).

English-80

SERVICE JOURNAL

Action Date, mtr reading, stamp, sign

50-Hour Service

1. Perform the 25-hour service.

2. Clean/replace the air cleaner’s fi lter cartridge (paper fi lter)
(shorter intervals for dusty operating conditions).

3. Change engine oil.

4. Lubricate according to lubrication chart.

5. Check/adjust the parking brake.

English-81

SERVICE JOURNAL

Action Date, mtr reading, stamp, sign

100-Hour Service

1. Perform the 25-hour service.

2. Perform the 50-hour service.

3. Change the engine oil fi lter.

4. Clean/replace the spark plugs.

5. Replace the fuel fi lter.

6. Clean the cooling fi ns on the engine and transmission.

7. Check V-belts.

8. Check tighten caster wheel axle bolts (every 200 hours).

9. Change the air fi lter’s paper cartridge.

English-82

SERVICE JOURNAL

Action Date, mtr reading, stamp, sign

300-Hour Service

1. Inspect the machine. Come to agreement with the customer
as to which additional work is to be carried out.

2. Perform the 25-hour service.

3. Perform the 50-hour service.

4. Perform the 100-hour service.

5. Check/adjust the mower deck.

6. Clean the combustion chamber and grind the valve seats.

7. Check the engine valve clearance.

8. Replace the air cleaner’s pre-fi lter (foam).

English-83

SERVICE JOURNAL

Action Date, mtr reading, stamp, sign

At Least Once Each Year

1. Clean the engine’s cooling air intake (25 hours).

2. Replace the air cleaner’s pre-fi lter (foam) (300 hours).

3. Replace the air fi lter’s paper cartridge.

4. Change the engine oil (50 hours).

5. Replace the engine oil fi lter (100 hours).

6. Check/adjust the cutting height.

7. Check/adjust the parking brake (50 hours).

8. Clean/Change the spark plugs (100 hours).

9. Change the fuel fi lter (100 hours).

10. Clean the cooling fi ns (100 hours).

11. Check the engine valve clearance.

12. Perform the 300-hour service at an authorized service workshop.

English-84

SERVICE JOURNAL

Action

Date, mtr reading, stamp, sign

English-85

WARRANTY

DIXON® ZTR® PRO SERIES COMMERCIAL / RESIDENTIAL WARRANTY POLICY

Black BearTM, Kodiak® & Grizzly™ Mowers

DIXON® WARRANTS ITS ZTR® MOWERS AGAINST DEFECTS IN MATERIAL AND WORKMANSHIP FOR THE PERIODS SET FORTH BELOW. THE

1. COMMERCIAL WARRANTY (use other than, or in addition to, mowing at owner’s primary place of residence):
a. First two years - 100% parts and labor subject to the conditions and limitations described herein with the exception of non-covered

items specifi ed below.

b. Third year - limited to 100% parts cost as shown in the current Dixon® Parts Price List and subject to the conditions and limitations

as described herein.
c. Attachments marketed through or approved by Dixon are warranted for one year parts and labor in commercial use applications.
d. Pro Series Models are not subject to hour meter restrictions.
e. Warranty applies to new mowers.

2. RESIDENTIAL WARRANTY (used only at owner’s primary place of residence):
a. Three years - 100% parts and labor subject to the conditions and limitations described herein for a period of three years from date of

purchase by the original owner.
b. Attachments marketed through or approved by Dixon are warranted for two years parts and labor in residential use applications.
c. Warranty applies to new mowers.

3. All Dixon® warranty must be accomplished by authorized Dixon® dealers and in accordance with Dixon® warranty policy and allow-

ances.

All warranty claims must be submitted to Dixon for approval.

4. Warranty labor reimbursement to dealers based on published Dixon® fl at rate schedule.

5. Warranty does not apply to damage in transit or incidents of misuse, negligence, accidents, or alteration. The use of parts or compo-

nents other than those supplied by Dixon VOIDS ALL WARRANTY.

SOLE REMEDY UNDER THIS WARRANTY IS REPLACEMENT OR REPAIR OF PARTS INCLUDING LABOR COSTS.

THIS WARRANTY IS SUBJECT TO THE FOLLOWING CONDITIONS AND LIMITATIONS:

6. Battery warranty is limited to 1 year from mower manufacture date.

7. The following items are not covered by this warranty policy:
(a) Routine maintenance or adjustments to include any oils, fi lters or other fl uids used.
(b) Belts, blades, tires and cosmetic appearance (paint, seat fade, etc.)
(c) Pick up and delivery charges for transportation of mower to and from an authorized Dixon® dealer’s place of business.
(d) Engines. These are covered under a separate warranty by each individual engine manufacturer. Consult engine manual for war-

ranty details.

(e) Any costs or expense of providing substitute equipment while repair work is being performed on a warranted mower.

8. THERE IS NO OTHER EXPRESS WARRANTY. TO THE EXTENT PERMITTED BY LAW, ALL IMPLIED WARRANTIES, INCLUDING

THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED; OTHERWISE, ALL SUCH IM­PLIED WARRANTIES ARE LIMITED TO THE SAME DURATION AND REMEDIES AS THE EXPRESS WARRANTY. ALL LIABILITIES
FOR CONSEQUENTIAL DAMAGES UNDER ANY EXPRESS OR IMPLIED WARRANTY ARE EXCLUDED.

English-86

Part No. 539 131266R01 09/25/07