Condensate
Pump
Installation and
Safety Instructions
CP-16
CP-16-230
CP-16
CP-16-230
Rated
Voltage
Rated
Current Draw
Input
Type
Head
Height
Flow Rate
at Zero Head
Temperature
Rating
Product Dimensions
(LxWxH)
Product
Weight
120 Volts / 60 Hz
1.9 Amps
USA 3-prong plug
16 . maximum
1.2 GPM
• Continuous duty 140F°
• Max inlet temperature 160F°
• Not suitable for contact with
steam or gasses that exceed 160F°
4.5” x 10.75“ x 6.5”
3.8 lbs.
220 Volts / 60 Hz (208-230)
1.0 Amps
NEMA 6-15 plug
16 . maximum
1.2 GPM
• Continuous duty 140F°
• Max inlet temperature 160F°
• Not suitable for contact with
steam or gasses that exceed 160F°
4.5” x 10.75“ x 6.5”
3.8 lbs.
Inlet Height
from Base
Included
Accessories
Wiring Color
References
3.5”
• Instruction Sheet
• Hang Tabs
• Plug Protector
• 4’ Remote Shuto Leads
• Inlet Cover
Black - Live/Hot
White - Neutral
Green - Ground
All installations must conform to
NEC requirements
3.5”
• Instruction Sheet
• Hang Tabs
• Plug Protector
• 4’ Remote Shuto Leads with
Insulated Terminals
• Inlet Covers (3)
Brown - Live/Hot
Blue - Neutral
Green/Yellow - Ground
All installations must conform to
NEC requirements
Limited Warranty
All pumps manufactured by or for DiversiTech Corporation (the Company) and sold by the Company under the DiversiTech brand are warranted to be free of defects in workmanship and materials for a period of
24 months from date of sale from the distributor to the contractor. The
Company will credit, repair or replace, at its option, any Pump if
deemed defective within this time period. All products returned to the
Company must include a return authorization issued by the Company.
The returned product should be suitably packaged and shipped
prepaid from the point of shipment to the point designated in the
Company's return authorization.
This warranty is a limited warranty and shall be in lieu of any other
warranties, expressed or implied, including, but not limited to, any
implied warranty of merchantability or tness for a particular purpose.
There are no other warranties that extend beyond the description of
the face hereof. The liability of the Company arising out of it's supply of
said products, or their use shall not in any case exceed the cost of
correcting defects in the products as set forth above. The Company
shall not be liable for any costs or damage incurred by its customers in
the removal or replacement of defective products from units in which
the products have been assembled. In no event shall the company be
liable for loss of prots, indirect, consequential, or incidental damages.
SAFETY WARNING
FOLLOW ALL SAFETY INFORMATION TO REDUCE POTENTIAL ELECTRICAL SHOCK.
DISCONNECT POWER BEFORE SERVICING UNIT. PUMP MUST BE PROPERLY GROUNDED.
NEVER USE THE PUMP TO MOVE FLAMMABLE LIQUIDS.
NEVER USE THE PUMP IN AN EXPLOSIVE GAS ENVIRONMENT,
OR WHERE GAS FUMES OR VAPOR MAY BE PRESENT.
ALWAYS DISCONNECT THE POWER PRIOR TO MOVING,
ADJUSTING OR SERVICING THE PUMP OR ATTACHED SYSTEMS.
WARNING: RISK OF ELECTRIC SHOCK
THIS PUMP MUST BE PROPERLY CONNECTED TO POWER FOLLOWING THE NATIONAL
ELECTRIC CODE NEC. FAILURE TO FOLLOW THESE WARNINGS WILL VOID WARRANTY AN
COULD RESULT IN AFATAL ELECTRIC SHOCK. A GREEN LED WILL INDICATE IF POWER IS
AVAILABLE. THIS PUMP IS SUPPLIED WITH A GROUNDING CONDUCTOR AND GROUND
INGTYPE ATTACHMENT PLUG. TO REDUCE THE RISK OF ELECTRIC SHOCK, BE CERTAIN THAT
IT IS CONNECTED ONLY TO A PROPERLY GROUNDED, GROUNDINGTYPE RECEPTACLE.
DiversiTech Corporation
6650 Sugarloaf Parkway
©2019 DiversiTech Corporation
PRINTED IN VIETNAM
Suite 100
Duluth,GA 30097
800.995.2222
FAX 770.593.8600
General Information
Thank you for the purchase of this DiversiTech condensate pump. This
pump is designed to automatically remove the condensate water that
collects from appliances such as air conditioners and de-humidiers.
The pump has a built-in tank that collects the water from the appliance.
When the water collected reaches sucient level inside the pump tank,
the pump switches on and pumps the water to a remote location for
disposal. When the tank is suciently empty the pump automatically
switches o.
The pump is capable of liing water to its rated height and is equipped
with a check valve that prevents water from owing back into the tank
when the pump shuts o.
The pump is also equipped with a switch that activates when the water in
the tank reaches an overow condition. The overow safety switch may
be connected to turn o the appliance if the high water condition occurs.
Pump should be stored indoors.
The chosen location should be clean and dry.
Unpacking
Carefully open the carton to avoid damage to the pump. Do not use a
knife or other sharp object that may scratch the pump’s cover. Aer
opening the carton, look for damage. If damage is found le a claim with
the freight carrier.
CHECK FOR
SHIPMENT
DAMAGE
Power Source
Connect power cord to a supply voltage and frequency that matches
what is shown on the pump nameplate. Source voltages lower than the
rated supply can reduce performance and cause the pump to overheat.
Pump Installation
The pump must be level and should be placed on a solid surface or oor.
The pump has rubber feet to reduce noise and keep it in place during
operation.
Do not use this pump in the presence of spraying or standing water,
it may cause a shock. This pump is not suitable for use in Class I or Class II
locations (explosive gas or dust).
Do not cover the pump air vents. The pump is air cooled. Do not cover
the vent holes located on the top or sides of the pump housing. The pump
may be operated continuously as long as the air vents are not covered.
Mounting
The condensate pump is equipped with optional mounting tabs which allow
the tank to be screwed to a wall or equipment side panel. The
screw-to-screw distance is 10-1/16”. When mounting into drywall or
concrete walls the screws must have anchors which provide the necessary
support in the wall material.
Inlets
4 inlet holes are located in the top deck of
the pump. Flexible vinyl tubing or PVC may
be connected to any of the pump inlets.
Knock out covers are provided to cover
unused inlets. Be sure to knock out only the
hole used for the inlet pipe to prevent the
pump from collecting debris or insects.
Tubing installed into the inlet holes must be straight. The tubing must not
bend inward where it will interfere with the pump or oat mechanism.
When using rigid tubing such as PVC, be sure to cut the end at an angle.
This will allow the condensate water to drain freely and keep the tubing
end from being blocked by the tank bottom.
It may be desirable to use a “P” or “U” trap between the AC unit and the
condensate pump to provide a liquid barrier to air ow from the air conditioner. These types of “traps” always contain some water which blocks the
ow of air from the AC unit which is wasteful and can cause other problems such as accelerated algae growth.
Outlets and Tubing Connections
The pump is equipped with a combination barb-type tting and check
valve. The tting allows the connection of 3/8” exible vinyl tubing such as
DiversiTech “CVT” clear vinyl. Attach the tubing by pressing it over the
barb tting and secure with a screw type hose clamp.
Route the tubing up and away from the pump; avoid compressing or
kinking the tubing. The tube route should be the shortest possible distance
from the pump to the building exterior or other drain location. For best
results the distance that the water must go UP should be shorter than the
distance that it goes DOWN. With the longer DOWN tubing, the length will
help siphon the condensate from the tank, speeding the pump out time.
Pump Electrical Connections
Connect the pump power to a properly grounded outlet capable of
providing power that exceeds the requirements listed on the pump nameplate. Avoid the use of extension cords wherever possible. The pump must
be operated by a continuous source of power and must not be connected
to switched outlets or other power supplies that may be inadvertently or
automatically turned o.
All aspects of the installation must conform to requirements of the NEC,
and any applicable local codes.
Safety Switch
The pump safety switch should be used
on 24V Class II control circuits only. The
pump safety switch connections are
to be connected in series with the 24 Volt
thermostat circuit to shut o A/C systems
should an overow condition occur. An
optional DiversiTech Universal Alarm may
be connected to indicate system trouble.
Pump Operation
Apply power by plugging in the pump. Test oat and safety switch by
manually lling the tank.
Test Safety Switch operation (if used) to be sure that the A/C system shuts
down when the pump has reached an overow condition.
Leak Check: Operate the pump by lling tank to trigger operation.
Pump Maintenance and Disassembly
Always disconnect power before performing maintenance.
Periodically inspect the Pump tank to assure it is free of accumulated dirt or
sludge. Do not use solvent cleaners. Clean Tank with soap and warm
water only. The check valve may be removed for cleaning or replacement by unscrewing with a 9/16 wrench. (illustration)
Clean inlet and outlet piping. Tubing may be cleared of slime or debris
instantly with a Wagner brand Gallo Gun tool and Swoosh cartridges.
Reassemble system and check for correct operation.
DOC32302
Loading...