Page 1
If you have any questions, comments or need to
reorder this set of cards, please call 1-800-558-2332
MoonBeam
Handling
Always wear personal protective equipment.
© 2020 Diversey, Inc. All RightsReserved.
*The hummingbird and wing shape logo is a trademark of Diversey, Inc.
Page 2
Securing the Cone
Removal from Base
Set the MoonBeamTM3 unit in the
desired location to get the most
coverage.
1
2
3
Lock the wheel caster
using the foot lever.
Twist the cone counter-clockwise and
remove by gently lifting up and clear
of the base – set it aside in a safe
spot.
Always wear personal protective equipment.
© 2020 Diversey, Inc. All RightsReserved.
*The hummingbird and wing shape logo is a trademark of Diversey, Inc.
Page 3
Securing the Cone
Replacing on Base
Confirm that the wheel caster
is locked using the foot lever.
1
2
3
Gently lower the cone on the
MoonBeam base. Make sure
the cone sits squarely on the base.
Gently turn the cone clockwise on
the base. The cone should screw on
smoothly, with little resistance.
If you feel resistance, unscrew
the cone, adjust its position slightly and
try again until it screws on smoothly.
Tighten until just snug. Don’t overtighten.
Unlock wheel caster to move unit.
Always wear personal protective equipment.
© 2020 Diversey, Inc. All RightsReserved.
*The hummingbird and wing shape logo is a trademark of Diversey, Inc.
Page 4
Replacing a Bulb
Confirm that the wheel caster
is locked using the foot lever.
1
2
3
Unplug the MoonBeam unit.
When handling light arm and
replacing/removing bulbs, take
care not to damage the clear
plastic bulb covering.
Always wear personal protective equipment.
© 2020 Diversey, Inc. All RightsReserved.
*The hummingbird and wing shape logo is a trademark of Diversey, Inc.
Page 5
Replacing a Bulb
Don gloves.
Place light where bulb is to
be replace into an upright
position that is comfortable
to reach.
4
5
6
Use your thumb to gently loosen
the black end cap on the arm and
remove using your fingertips.
Tilt the light arm so the end is about
waist high, grasp the bulb at the end,
and gently but firmly pull the bulb from
the light arm. It will release with a “snap.”
Gently jiggle the bulb to clear the
light arm opening. Dispose of used bulb
according to facility protocol.
Always wear personal protective equipment.
© 2020 Diversey, Inc. All RightsReserved.
*The hummingbird and wing shape logo is a trademark of Diversey, Inc.
Page 6
Replacing a Bulb
Return light arm to upright position
and feed new bulb into light arm.
Gently push into socket. bulb will
click into place. Prepare to gently
replace black cap. See step 8 below.
7
8
9
When replacing black cap, note that
the bulbs should nest between two
translucent placement tubes (these
look like bits of soda straws). Be sure
these tubes are in place and bulbs
fit in between when replacing cap.
Check that cap is fully seated on light
arm.
To verify successful bulb installation,
power on the MoonBeam unit.
Page 7
Rubber End Cap
Removal, Replacement, Positioners
Rubber End Caps with Positioners must be intact to
have positive transport and secure end caps.
If the little plastic positioners (white plastic positioner) fall out the
bulbs will be loose and mobile. This seems to be the biggest issue.
The caps will also fall off if the positioners fall off.
If they are all intact, the bulbs will not move and they will transport
better.
If they fall out, the bulbs will no longer be stable and the caps will fall
off. Based upon the fact this is so isolated with few customers, I don't
want to presume, and just want to confirm. The straws do fall out and
most be repositioned back in or we will have 100% failure.
If they are in then there is little need to pull the caps off.
In the second image you can see how they position the bulbs to keep
secure as well as a diagram to the right.
© 2019 Diversey, Inc. All Rights Reserved.
*The hummingbird and wing shape logo is a trademark of Diversey, Inc.
Page 8
Troubleshooting General
Page 9
Troubleshooting Cont’d.
Page 10
If you have any questions, comments or need to reorder
this set of cards, please call 1-800-558-2332
Diversey has been, and always will be, pioneers and facilitators for life.
We constantly deliver revolutionary cleaning and hygiene technologies
that provide total confidence to our customers across all of our global
sectors. Headquartered in Fort Mill, South Carolina, USA, Diversey
employs approximately 9,000 people globally, generating net sales of
approximately $2.6 billion in 2017.
For more information, visit www.diversey.com or follow us on socialmedia.
© 2020D iversey,Inc. All Rights Reserved.
Loading...