Installation Instruction
ALG Series LED Area Light Version: 3.1
IMPORTANT SAFETY INSTRUCTIONS
READ CAREFULLY BEFORE INSTALLING THE FIXTURE. RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/ abrasions,
and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.
Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
Installation and service of luminaires should be performed by a qualified licens ed electric ian.
Maintenance of the luminaires shou ld be perform ed by person(s) familiar with the luminaires’ construction and
operation and any hazards involved. Regular fixture maintenance programs are recommended.
It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on
ambient dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a solution
of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical
assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damag ed gaskets as
necessary.
DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have
been damaged during transit. Thoroughly inspect the fixture for any freight damage; freight damage should be
reported to the delivery carrier.
WARNING: RISK OF ELECTRIC SHOCK
RISK OF ELECTRIC SHOCK. Make sure power supply is OFF before installing or maintaining fixture. No user
serviceable parts inside.
Verify that supply voltage is correct by comparing it with the luminaire label information.
The fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper
grounding is required for safety.
All wiring connections should be capped with UL approved recognized wire connectors.
WARNING: RISK OF BURN
Never perform maintenance or cleaning while fixture is energized. Disconnect power and allow fixture to cool before
maintaining.
Do not exceed maximum wattage marked on luminaire label.
Follow all manufacturer’s warnings, recommendations and restrictions for: driver type, burning position, mounting
locations/methods, replacement and recycling.
CAUTION: RISK OF INJURY
Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing
maintenance.
Avoid direct eye exposure to the light source while it is on.
CAUTION: RISK OF FIRE
Keep combustible and other materials that can burn, away from lamp/lens.
Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying.
CAUTION: RISK OF PRODUCT DAMAGE
Never connect components under load.
Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.
Controls for dimming, auto-sensing, or remote control of a luminaire that are not factory-wired to the luminaire must
be checked for compatibility with the luminaire prior to installation. Never connect an LED product directly to a
dimmer pack that has not been pre-approved. LED fixtures must be powered directly off a switched circuit.
Installation Instruction
ALG Series LED Area Light Version: 3.1
Unless individual product specifications deem otherwise: do not restrict fixture ventilation. Allow for some volume of
airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent
convection or conduction cooling.
Unless individual product specifications deem otherwise: do not exceed fixture maximum ambient temperature.
Only use fixture in its intended location.
LED products are Polarity Sensitive. Ensure proper Polarity before installation.
Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during
all installation or servicing of the unit.
Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
Some components inside the fixture may not be serviceable. In the unlikely event your unit may require service, stop
using the unit immediately and contact your sales representative for assistance.
User should prepare necessary accessories and spare parts (not provided) including junction box, cross bar, junction
box gasket, surface plate and screws.
Always read the fi xtures comple te ins ta l lat io n in s tructions prio r to ins ta ll a t ion for a ny additional fixture specific
warnings.
CAUTION: INTENDED APPLICATION
Input voltage: 120-277VAC (347VAC/480VAC optional), 50/60Hz
MIN. 90°C supply conductors
Operating temperature: -20°C to 40°C standard (-40°C to 50°C optional)
Suitable for wet location
Mounting height: above 4 feet (1.2 meter)
Installation Instruction
ALG Series LED Area Light Version: 3.1
MOUNTING
Mounting Adaptor
Arm
Gasket
Bolster Plate
Fixture
Mounting
Arm
Gasket
Bolster Plate
Fixture
This area light is available in SQUARE/ROUND POLE ARM, ADJUSTABLE SLIP FITTER, ADJUSTABLE
TRUNNION mountings.
A: SQUARE OR ROUND POLE ARM MOUNT______________________________________________
1. Remove ARM COVER from ARM.
2. Locate ARM onto POLE, and insert LONG BOLTS through ARM, GASKET and threaded into BOLSTER
PLATE.
3. Slide MOUNTING ADAPTOR of FIXTURE into ARM.
4. Tighten (4) socket head set screws located on top of MOUNTING ADAPTOR.
5. Route the cord coming from the fixture through ARM and then through pole.
6. Install ARM COVER back to ARM.
`
Adaptor
B: ADJUSTABLE SLIP FITTER MOUNT__________________________________________________
1. Install ADJUSTABLE SLIP FITTER on to TENNON.
2. Slide MOUNTING ADAPTOR of FIXTURE into SLIP FITTER ADAPTOR.
3. Tighten (4) socket head set screws located on top of MOUNTING ADAPTOR.
4. Route the cord coming from the fixture through MOUNTING ADAPTOR, SLIP FITTER ADAPTOR, TENNON
ADAPTOR and then through pole.
Installation Instruction
ALG Series LED Area Light Version: 3.1
Mounting Adaptor
Slip Fitter Adaptor
Tennon Adaptor
U-bracket
Fixture
Trunnion
C: ADJUSTABLE TRUNNION MOUNT_____________________________________________________
1. Check that the surface structure is drilled according to Trunnion Mount Drilling Pattern, drill a minimum of three
(3) holes in the surface where the luminaire is to be mounted.
2. Ensure that the mounting position can safely support the weight of the luminaire
3. Mount the Trunnion Bracket using studs to the surface structure. Make sure that Trunnion Bracket (B) is securely
attached
4. Adjust angle as needed
5. Slide Fixture Head and Mounting Adaptor onto Trunnion Bracket. Tighten 4x screws on top of Mounting Adaptor
6. Make necessary electrical connections. SEE WIRING for Electrical Connection and wiring diagram instructions.
Bracket
Mounting
bracket
Installation Instruction
ALG Series LED Area Light Version: 3.1
WIRING
1. Wire input end of the LED driver to supply wires using
appropriate wire nut according to wiring section. Wire
connections must be insulated and waterproof.
2. Connect the BLACK/BROWN lead to LINE (+) supply lead.
3. Connect the WHITE/BLUE lead to NEUTRAL/COMMON
(-) supply lead.
4. Connect the GREEN lead to GROUND supply lead.
If any, connect PURPLE/BLUE to 0-10V SIGNAL supply
lead and GREY/WHITE to 0-10V NEUTRAL/REFERENCE
supply lead.
Loading...