DITEC VALOR Technical Manual

Ditec VALOR

Sliding doors automation

(Original instructions)

IP1950 EN

Technical manual

www.ditecentrematic.com

2

IP1950EN - 2013-09-13

Index

Subject Page

1. General safety precautions 3

2. Declaration of incorporation of partly completed machinery 4

2.1 Machinery directive 4

3. Technical data 5

3.1 Applications 5

4. Standard installation 6

5. Installation of the automation 7

5.1 VALOR box fastening 7

5.2 VALOR T box fastening 8

5.3 VALOR H box fastening 9

5.4 Preparation of glass door wing 11

5.5 VALOR - VALOR H door wing installation and adjustment 12

5.6 VALOR T door wing installation and adjustment 13

5.7 Floor guide installation 15

5.8 Belt adjustment 16

5.9 Lock installation 16

6. Electrical connections 17

7. Ordinary maintenance program 18
User instructions 19

General safety precautions 19
Manual release instruction 21
Function selector user instructions 22

Key

This symbol indicates useful information for the correct functioning of the product.

This symbol indicates instructions or notes regarding safety, to which special atten­tion must be paid.

i

3

IP1950EN - 2013-09-13

1. General safety precautions

This installation manual is intended for qualified personnel only.
Installation, electrical connections and adjustments must be performed in accordance with
Good Working Methods and in compliance with the present standards.
Read the instructions carefully before installing the product.
Bad installation could be dangerous.

The packaging materials (plastic, polystyrene, etc.) should not be discarded in the environ-

ment or left within reach of children, as these are a potential source of danger.
Before installing the product, make sure it is in perfect condition.
Do not install the product in explosive areas and atmospheres: the presence of inflammable
gas or fumes represents a serious safety hazard.
Before installing the motorisation device, make all the necessary structural modifications in
order to create safety clearance and to guard or isolate all the crushing, shearing, trapping
and general hazardous areas.
Make sure the existing structure is up to standard in terms of strength and stability. The mo­torisation device manufacturer is not responsible for failure to observe Good Working Methods
when building the frames to be motorised or for any deformation during use.

The safety devices (photocells, safety edges, emergency stops, etc.) must be installed

taking into account: applicable laws and directives, Good Working Methods, installation
premises, system operating logic and the forces developed by the motorised door.
The safety devices must protect the crushing, cutting, trapping and general hazardous areas
of the motorised door.
Display the signs required by law to identify hazardous areas.
Each installation must bear a visible indication of the data identifying the motorised door.
When requested, connect the motorised door to an effective earthing system that complies
with current safety standards.
During installation, maintenance and repair operations, cut off the power supply before opening
the cover to access the electrical parts.
The automation protection casing must be removed by qualified personnel only.

The electronic parts must be handled using earthed antistatic conductive arms.

The manufacturer of the motorisation declines all responsibility in the event of component

parts being fitted that are not compatible with the safe and correct operation.
Use original spare parts only for repairs or replacements of products.
The installer must supply all information on automatic, manual and emergency operation of the
motorised door and must provide the user with the operating instructions.

Failure to observe the information in this manual may result

in minor personal injury or damage to equipment.

Save these instructions for future reference.

4

IP1950EN - 2013-09-13

2. Declaration of incorporation of partly com­pleted machinery

2.1 Machinery Directive

(Directive 2006/42/EC, Annex II-B)
The manufacturer Entrematic Group AB with headquarters in Lodjursgatan 10, SE-261 44
Landskrona, Sweden
declares that the automation system for Ditec VALOR sliding doors:

- has been constructed to be installed on a manual door to construct a machine pursu-

ant to the Directive 2006/42/EC. The manufacturer of the motorized door shall declare
conformity pursuant to the Directive 2006/42/EC (annex II-A), prior to the machine being
put into service;

- conforms to applicable essential safety requirements indicated in annex I, chapter 1 of

the Directive 2006/42/EC;

- conforms to the Low Voltage Directive 2006/95/EC;

- conforms to the Electromagnetic Compatibility Directive 2004/108/EC;

- technical documentation conforms to Annex VII-B to the Directive 2006/42/EC;

- technical documentation is managed by Marco Pietro Zini with offices in Via Mons. Banfi,

3 - 21042 Caronno Pertusella (VA) - ITALY;

- a copy of technical documentation will be provided to national competent authorities,

following a suitably justified request.

Landskrona, 15-01-2013 Marco Pietro Zini
(President)

Pursuant to Machinery Directive (2006/42/EC) the installer who motorizes a door or gate has
the same obligations as the manufacturer of machinery and as such must:

- prepare the technical file which must contain the documents indicated in Annex V of the

Machinery Directive;

(The technical file must be kept and placed at the disposal of competent national authori-

ties for at least ten years from the date of manufacture of the motorized door);

- draw up the EC Declaration of Conformity in accordance with Annex II-A of the Machinery

Directive and deliver it to the customer;

- affix the EC marking on the motorized door in accordance with point 1.7.3 of Annex I of

the Machinery Directive.

5

IP1950EN - 2013-09-13

Service class: 5 (minimum 5 years of working life with 600 cycles per day).
Applications: VERY INTENSE (for shared entrances with very intense pedestrian use).

Service class: 6 (minimum 5 years of working life with continuous use).
Applications: CONTINUOUS (for all special situations with continuous use).

- Performance characteristics are to be understood as referring to the recommended weight
(approx. 2/3 of maximum permissible weight). A reduction in performance is to be expected
when the access is made to operate at the maximum permissible weight.

- Service class, running times, and the number of consecutive cycles are to be taken as merely
indicative having been statistically determined under average operating conditions, and are
therefore not necessarily applicable to specific conditions of use. During given time spans
product performance characteristics will be such as not to require any special maintenance.

- The actual performance characteristics of each automatic access may be affected by independ­ent variables such as friction, balancing and environmental factors, all of which may substan­tially alter the performance characteristics of the automatic access or curtail its working life
or parts thereof (including the automatic devices themselves). When setting up, specific local
conditions must be duly borne in mind and the installation adapted accordingly for ensuring
maximum durability and trouble-free operation.

3. Technical data

Ditec VALOR L-H Ditec VALOR P Ditec VALOR N Ditec VALOR T

Power supply 230 V~ 50/60 Hz 230 V~ 50/60 Hz 230 V~ 50/60 Hz 230 V~ 50/60 Hz

Power fuse F1A

F1A
F1,6A with weight
>200 kg

F1A
F1,6A with weight
>200 kg

F1A
F1,6 A with weight
>200 kg

Rated power input 200 W 300 W 300 W 300 W
Max speed 1 wing 0,8 m/s 0,8 m/s 0,8 m/s -
Max speed 2 wings

1,6 m/s

1,6 m/s
1,2 m/s with
weight 180 kg

1,6 m/s
1,2 m/s with
weight 180 kg

0,8 m/s

Max speed 4 wings - - - 1,6 m/s
Service life 5 - HEAVY DUTY 6 - CONTINUOUS 6 - CONTINUOUS 6 - CONTINUOUS
Intermittence S3 =100% S3=10 0% S3=100% S3=100%
Max door weight 1 wing

100 kg

120 kg
100 kg 1 break­out door wing

120 kg 200 kg

Max door weight 2 wings

180 kg

220 kg
180 kg 2 break­out door wings

240 kg 260 kg

Door weight with reinfor­ced wheels 1 wing

- - 150 kg -

Door weight with reinfor­ced wheels 2 wings

- - 300 kg -

Temperature -20 °C - +55 °C -20 °C - +55 °C -20 °C - +55 °C -20 °C - +55 °C
Temperature with

batteries

-10 °C - +50 °C -10 °C - +50 °C -10 °C - +50 °C -10 °C - +50 °C

Degree of protection IP20

(FOR INTERNAL
USE ONLY)

IP20
(FOR INTERNAL
USE ONLY)

IP20
(FOR INTERNAL
USE ONLY)

IP20
(FOR INTERNAL
USE ONLY)

Control panel EL20 EL20 EL20 EL20
Accessories power

supply

24 V

0,5 A 24 V 0,5 A 24 V 0,5 A 24 V 0,5 A

3.1 Operating instructions

6

IP1950EN - 2013-09-13

4. Standard installation

Ref. Code Description

0 VALOR Operator
1 Drive unit
2 EL20 Control panel
3 AL2 Transformer
4 VALABE

VALABC

Emergency batteries (optional)
No-break batteries (optional)

5

PAS024AMW (microwave+infrared), or
PASAA2 (only infrared)

Combined sensor for opening and safety during closing
external side

6A

PAS024AMW (microwave+infrared), or
PASAA2 (infrared only)

Combined sensor for opening and safety during closing
internal side (operator)

or

6B

PASM24W (microwave), or
PASM243 (microwave), or
PASS24 (microwave), or
PASS24W (microwave), or
PASA (infrared)

}

+ PASAT 3I
(infrared)

Opening sensor (a) + Safety during closing sensor (b) inter­nal side (inside the operator’s housing)

7

PASAT3
PASAT3I

Safety during opening sensor (outside or inside the opera­tor’s housing)

8 VALSB

LOKSBM

Integrated release handle
Release handle

9 COME - COMHK Functions selector switch

10 CELPR Photocells (NOT ACCORDING TO STANDARD EN 16005)

11 MD1 Display

12 PFP1 - PFP2 - PDP1 - PDP2 Open push buttons

A Connect the power supply to an approved omnipolar switch with an opening distance of the contacts of at least

3mm (not supplied). The connection to the mains must be made via an independent channel, separated from
the connections to command and safety devices.

A

11

3

1

2

4

6A

6B

7

0

8

9

10

12

7

GND

5

a

b

6B

7

IP1950EN - 2013-09-13

i

The given operating and performance features can only be guaranteed with the use of
DITEC accessories and safety devices.

5. Installation of the automation

5.1 VALOR box fastening

70 max

0KP515AB

+/- 8

+/- 6

175

80

90

38

2728H

10 HM = H + 18

145

Unless otherwise specified, all measurements are expressed in millimetres (mm).
The VALOR automation wall fixing measurements are illustrated in the diagram, considering that
the door wing profiles are not of our production.
If the door wings are made with DITEC profiles of the PAM series: refer to the measurements in
the related manuals.
WARNING: if the door wings are fitted with a break-out device, use the carriages with brackets
with 3 fixing points.
Fix the box with M6 Ø12 steel plugs or 6MA screws. Distribute the fixing points approx. every 800
mm.
Make sure that the box is level and its top surface is perpendicular with the floor and not deformed
lengthwise with the shape of the wall. If the wall is not straight and smooth, the box must be fixed
to metal plates.
WARNING: The fastening of the box to the wall must be suitable in order to sustain the weight of
the door wings.

Wiring passage

8

IP1950EN - 2013-09-13

5.2 VALOR T box fastening

KPAM45

KPAM45

255

160

70 max 70 max

90

38

2728

H

12

145

+/- 8

HM=H+16

+/- 6 +/- 6

Unless otherwise specified, all measurements are expressed in millimetres (mm).
The figure shows the measurements for wall mounting the VALOR H automation considering that
the door wings are made of DITEC PAMH60 series profiles.
If the PAMH60 door wing has lead-shielding (e.g. radiology department) refer to the measure­ments marked [*].
Fix the box with M6 Ø12 steel plugs or 6MA screws. Distribute the fixing points approx. every 800
mm.
Make sure that the box is level and its top surface is perpendicular with the floor and not deformed
lengthwise with the shape of the wall. If the wall is not straight and smooth, the box must be fixed
to metal plates.
WARNING: The fastening of the box to the wall must be suitable in order to sustain the weight of
the door wings.

Wiring passage