Displays2go VWALL3+ VWALLB, VWALL3+ VWALLWH Installation Manual
INSTALLATION MANUAL
Video Wall Stand and Accessories
8
5
2
Note: The displ ays a re in sta lle d by the numer ica l ord er gi ven.
7
4
1 3
9
6
Note: The angle o f dis pla ys ar e adj usted by the n ume ric al or der given.
Maint ena nce
• Check t hat t he br ack et is secure and sa fe to u se at r egu lar intervals (at l eas t eve ry three months ).
• Pleas e con tac t you r distributor i f you h ave a ny qu estions.
VW AL L3 + VW AL LB S
VW AL L3 + VW AL LWH
200x2 00/ 300 x30 0
400x2 00/ 400 x40 0
600x4 00
CA UT ION: DO N OT EXCEED
RATE D LIS TED WE IGH T. SERI OUS
INJ URY OR P ROP ERTY DAMA GE
MAY OCCUR!
55"
MAX
50k gx3
50k gx3
(110 lbsx3 )
(110 lbsx3 )
RATED
RATED
NOTE: Rea d the entire instr uction manual be fore you st art ins tallati on and assembly.
WARNING
VWALLWH
• Do not begin the installation until you have read and understood all the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
Component Checklist
IMPORTANT: En sur e that you ha ve re cei ved a ll parts ac cor din g to th e com ponent ch eck lis t pri or to insta lla tio n.
If an y par ts ar e mis sing or fau lty, t ele phone you r loc al di str ibutor fo r a rep lac eme nt.
middl e bas e (x1 )
H
conne cti ng
piece ( x1)
M
connecting fitting (x3)
S
M8x65 ( x8)
N
column (x1)
left ba se I(x1) right b ase J(x1)
M8x35 ( x4)
universal plate (x3)
V
O
6mm Al len k ey (x 1)
T
P
left co ver K(x1) right c ove r(x 1)
D8 wash er (x 4)
Q
adapter bracketU (x6)
cable c lam p (x1 2)WM8x16 ( x4)
wrenc h (x1 )
R
X
L
VWALLBS
iron ex pan sio n bol t (x6)
D
steel plate (x1)
A
M8x16 ( x6)
E
rubber pad (x4)
B
M8x40 (x4 )
conne cti ng pl ate ( x1)
F
C
5mm Al len k ey (x 1)
G
top cov er (x 1)
Y
Package M (x3)
M5x14
(x4)
M-A
M8x30
(x4) small s pac er (x 8)
M-E
3mm Al len k ey (x 1)
Z
M6x14
M-B
washe r
M-F
4mm Al len k ey (x 1)
Z1
(x4)
(x4)
5mm Al len k ey (x 1)
M8x20
(x4)
M-C
M-G
Z2
6mm Al len k ey (x 1)
Z3
M6x30
(x4)
M-D
big spa cer ( x4)
M-H
21
1a. VWALLBSFor
1a-1. Installing the Rubber Pads
1a-2b. For the Floor Stand Mounting
G/Z2
Remov e the c abl e tie s.
A
B
E
• Lift the steel base by grasping the cabl e ties .
• Peel off the ba ckin g paper from th e rubber pads and stick the ru bber
pads on to the st eel base.
1a-2a. For Concrete Floor Mounting
C
Mark th e exa ct lo cat ion of mounting h ole s and p re- drill these mou nti ng ho les w ith a 12mm drilli ng bi t to
at leas t 62m m in de pth . Remove the dust i n the h ole s.
D
G/Z2
First t igh ten t he ir on expansion bo lts w ith a n Alle n key, and th en lo osen the iro n exp ans ion b olts in order
to sepa rat e the b olt s and the expansi on tu bes .
V
F
G/Z2
60mm
62mm
(2.4")
(2.4")
ø12mm
(ø 1/2 ")
Attach the column to the steel base using the appropriate screws. Tighten all screws with an Allen key.
1b. For VWALLWH
1b-1. Assembling the Base
H
I
J
R
N
Attach the left and right base to the middle base using the appropriate screws. Tighten all screws with an Allen key.
P/Z3
Each castor can be adjusted independently
for fine tuning. Slightly turn the nut to lower
or raise the base.
Note: W ith t he br ake
wheel s fac ing f orw ard.
1b-2. Attaching the Column to the Base
M
Q
O
• Attac h the connecting pl ate to the bott om of the colum n using the
appropriate sc rews. Tighten all sc rews with an Allen key.
• Insert an expans ion tube into e ach of th ese ho les. Using th e bolt s
mount the column to the floor. Tighten all sc rews with an Allen key.
3
G/Z2
D
P/Z3
Attach the column to the assembled base using the connecting piece, secure them with the appropriate screws.
NOTE: Lock the brakes on the casters to avoid any sudden movements during installation.
4
Loading...