Displays2go HVAWM4290L Instructions Manual
HVAWM4290L
INSTRUCTIONS
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE! IF
YOU DO NOT UNDERSTAND THE INSTRUCTIONS, OR DO NOT FEEL THAT YOU CAN FOLLOW
THEM SAFELY, CONTACT A QUALIFIED CONTRACTOR. THE WARRANTY WILL BE HONOURED IF
ACCOMPANIED BY AN ORIGINAL SALES RECEIPT, AND ONLY IF THE INSTRUCTIONS HAVE
BEEN FOLLOWED EXACTLY.
The HVAWM4290L
·
a wood stud is included. For mounting to any other surface, it is recommended you contact a
qualified contractor.
· The wall or mounting surface must be capable of supporting the combined weight of the mount
and the display, otherwise the structure must be reinforced.
· Safety gear and proper tools must be used. A minimum of two people are required for this installati
Failure to use safety gear and/or attempting this installation alone can result in property damage,
serious injury, or death.
· Follow all instructions and recommendations regarding adequate ventilation and suitable locations for
mounting your flat panel. Consult the owner
· This product will hold flat panels up to 90” and weighing up to 200 lbs.
· VESA 800mm x 600mm
is designed to mount a panel onto a vertical wall. Hardware for mounting to
on.
‘s manual for your flat panel for more information.
Tools Required
· Stud finder ("edge to edge" stud finder is recommended)
· Phillips screwdriver
· Pencil
· Hammer Drill (Concrete installation only)
· 1/4" drill bit for wood studs, 3/8” drill bit for concrete
· 7/16" socket wrench or bit driver for wood screws
· Level
· Tape measure
A
M5*15mm
(x4)
I
Wall Plate (x1)
B
M5*25mm
(x4)
C
M6*12mm
(x8)
J
D
M6*25mm
(x4)
Parts List
Adaptor Plate (x1)
E
M8*15mm
(x4)
K
F
M8*15mm
(x4)
L
Adaptor Brackets (x2)
G H
M8*30mm
(x4)
M
Metal Washer
φ6mm (x8)
N
Metal Washer
φ8mm (x4)
1
Spacers (x4)
Slider Plates
(x4)
Allen Key (x1)
Lag Bolt
8*70mm (x4)
Anchor (x4)
Step 1A - Mounting the wall plate to wooden studs (Fig. 1)
The HVAWM4290L can be mounted onto two wooden studs, with center
to center istances between 16" (406mm).
Using an electronic stud finder, locate the center of the two wooden studs at the
desired mounting location. Mark the stud center positions directly on the wall.
Connect the stud marks with a horizontal line and find the center between them
to represent where you wish the center of the scree
measure and mark the center of this horizontal line.
Place the wall plate on the wall. Pin the wall plate to the center mark on the wall.
Using a level (bubble or laser ), level the guide, and
then press the adhesive backi
ng against the wall to
hold the guide in place. Using a 1/4" (6mm) drill bit,
drill 4 pilot holes into the center of the studs (through
the mounting hole cut-out sections of the template),
down to a depth of 3" (76mm).
NOTE: It is not recommended to use a drill driver or impact
wrench to tighten bolts. Tighten lag bolts so that wall plate
is firmly attached to wall, but DO NOT over-tighten. The lag
bolts can be damaged by over-tightening which will strip
their threading. Final tightening of lag bolts
should be done by hand using a ratchet
wrench and socket.
n to be located. Be sure to
6mm (1/4”)
Lag Bolt
8*70mm
Hole
Fig. 1
Wood Stud
CAUTION: Two people recommended
for lifting
Step 1B - Mounting the wall plate to concrete (Fig. 2)
Place the wall plate on the wall. Pin the wall plate to the center mark on the wall. Using a level (bubble or
laser), level the guide, and then press the adhesive backing against the wall to hold the guide in place.
Using a 3/8" (10mm) masonry drill bit, drill 4 mounting holes 3-1/8" (80mm) deep into the concrete/masonry
surface.
NOTE: It is not recommended to use a drill driver or impact wrench to tighten bolts. Tighten lag bolts so that wall plate is
firmly attached to wall, but DO NOT over-tighten. The lag bolts can be damaged by over-tightening which will strip their
threading. Final tightening of lag bolts should be done by hand using a ratchet wrench and socket.
Fig. 2
10mm (3/8”)
Hole
Wall Anchor
Lag Bolt
8*70mm
CAUTION: Two people recommended
2
for lifting
Loading...