Display Devices PL-3000 User Manual

Download

PL3000

PlasmaLift

Installation &

Owners Manual

February 2007

sales@displaydevices.com www.displaydevices.com

(303) 412-0399 fax: (303) 412-9346 5880 N. Sheridan Blvd, Arvada, CO 80003

PL3000 PlasmaLift

Installation Instructions

Ensure the ceiling structure is capable of holding at least four times the combined weight of the lift (300 lbs.) and Plasma Display (74 – 140 lbs). This is a minimum requirement. Follow any local or state codes that apply to your specific area.

1.) If you have not already done so, install structural mounting points above the ceiling. For most installations, P3000 Unistrut® with all-thread works very well.

2.) Raise lift with a Genie® type material lift into position. The bottom of the lower metal frame/door should be level with the bottom of the finished ceiling.

3.) Attach 1/2” (M12) mounting hardware (bolt/thread, 2-washers, lock washer and nuts) to six of the 12 mounting holes on the top of the frame front & rear.

4.) Level the lift frame, front-to-back and side-to-side and tighten hardware. Be sure unit is level for proper mechanical operation.

5.) Attach handheld remote to control box… see Control Interface section below.

6.) Attach the power cord to the unit – LED on control box will flash upon power to the unit. There is no power on/off switch on this lift.

7.) Press show to lower the unit.

8.) Attach the mount to the plasma display with the enclosed hardware.

9.) Raise the PDP to the lower panel and attach with ¼-20 bolts/washers to the lowering panel. The interface mount should be level with the lowering panel.

10.) Press home to raise the PDP into the lift. Be cautious that your display does not contact the lift when raising. Be sure the closure door does not contact the PDP. If it does, then raise up the PDP to the next set of mounting holes. Lower the plasma display.

11.) If possible, it is best to add power and signal cables to the plasma display while the lift is in the closed position. Do not use thick cables that have a large bend radius. Begin your power/signal cable runs from the display so no splices will have to be made inside the lift. Feed cables into the scissors beginning at the PDP and work up. Affix the cable with the enclosed cable ties at each cable tie down along the scissors going over the cables. Leave a loop when at the end of the scissor.

NOTE: Your cables alternate front-to-back on the scissor assembly.

Begin at fixed pivot point

oop under

oop over

End point

Cable Management

12.) Operate the lift up and down a few times to be sure that are no cables

13.) Verify that when the door is shut it is level with the unit frame, if not adjust

binding anywhere on the lift.

the all-thread arms on the left and right sides as needed.

PL3000 PlasmaLift

Programming Show Position

Programming can only be done with three-button control. If other methods of triggering the lift are normally used, first program the lift with the buttons and then configure lift for other trigger method.

1.) Press ‘HOME’ button. Unit raises to the home or stored position.

2.) Press and hold ‘STOP’ button for 10 seconds – unit is now in manual mode.

3.) Press ‘SHOW’ button momentarily – unit will travel down. When unit reaches desired show position press ‘STOP’ button momentarily. THIS MUST BE DONE IN ONE MOTION, DO NOT PRESS HOME, SHOW, OR STOP FOR FINE TUNING OF POSITION.

4.) Press and hold ‘STOP’ button for 10 seconds.

5.) Press ‘HOME’ button momentarily – unit will travel to home position.

6.) Lift is now set – press ‘SHOW’ button to verify – unit should travel down to show position. If you start this procedure and wish to quit after step 2, you must reset power to lift before normal operation (unplug unit or reset electrical breaker.

Control Interface

8 7 6 5

Low Voltage Control Lines:

There are three integrated methods of control and two optional methods. The standard controls are three momentary buttons (contacts) or low-voltage control signal, or single-latching contact. The optional methods are remote IR or RF control; please contact DDI for information on those options.

Three button control:

‘Home’ button (BLACK) Pin 6 ‘Show’ button (RED) Pin 5 ‘Stop’ button (GREEN) Pin 1 Common (WHITE) for all buttons Pin 4

Low voltage (5 vdc < V < 24 vdc) control signal:

Jumper Pin 6 to Pin 4, and jumper Pin 5 to Pin 4 Trigger Voltage to Pin 2 Trigger Voltage ground Pin 4. (applied voltage sends lift up, no voltage sends lift down)

Single latching contact:

Jumper from Pin 6 to Pin 4, and jumper Pin 5 to Pin 4 Contacts between Pin 3 and Pin 2 (contact closed sends lift up, contact open sends lift down)

Control Box

Side View

4 3 2 1

38.000

DRAWING REVISION BLOCK

REV ECO DESCRIPTION DRAWN CHECKED APPROVED DATE

A - INITIAL RELEASE JTW 5/14/2003 BCECO-0310

D ECO-0471

38.00 W AS 36.00 JTW UPDATED BOM JTW REP LACED TI LT MOUNT WITH UNIVERSAL MOUNT BSV

10/17/2003

4/18/2005

11/27/2006

23.500

20.000

EXTENDED

49.000

RETRACTED

THE INFORMATION CONTAINED

IN THIS DRAWING IS THE

PROPERTY OF DISPLAY

DEVICES, INC. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE

WRITTEN PERMISSION OF DISPLAY DEVICES, INC IS

PROHIBITED

DRAWN

CHECKED

MATERIAL

FINISH

JTW

UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES.

TOLERANCES:

.XX = .02 .XXX = .XXXX = ANGLE =

DATE

.010 .0050

0.5

5/13/2003

ISOMETRIC VIEW

DISPLAY DEVICES, INC

5880 SHERI DAN BLVD

ARVADA, CO 80003

TITLE

PL3042

DRAWING NO.

SIZE

SCALE

FILE NAME

NONE

402-001

402-001.SLDDRW

SHEET 1 OF 2

REV

456

7 9 8

11 13 12

ITEM NO QTY PART NO DESCRIPTION

1 1 402-003 FRAME ASSY

2 1 402-004 MOTOR & DRUM ASSY 3 1 404-005 SLIDE ASSY

108

4 4 5900-12600 1/4-20 X 1/2, HHCS, HX, GR5, PL 5 12 5950-12200 1/4, FL WASHER, STL, ZI 6 4 5950-13250 1/4, LK WASHER, STL, PL 7 8 5900-13800 3/8-16 X 2.00, HHCS, HX, GR5, PL 8 16 5950-12650 3/8, FL WASHER, TH, PL 9 8 5950-13300 3/8, LK WASHER, STL, PL

10 8 6000-11400 3/8-16, HX NUT, STL, ZI 11 8 5900-15850 5/16-18 X 3/4, HHCS, HX, GR5, PL 12 8 5950-12300 5/16, FL WASHER, STL, ZI 13 8 5950-10700 5/16, LK WASHER, STL, PL 14 1 115-535 UNIV. MT. & TILT MTING. BK. ASSY. 15 4 5900-20600 1/4-20 X 3/4, HHCS, HX, GR5, PL 16 4 6000-13350 1/4-20,NYLK NUT, STL, ZI