Disney 72-4131-250 User Manual

Dumbo Pylon

Owner’s Manual

72-4131-250

8/03

© Disney

C

ongratulations on your purchase of the Lionel Dumbo Pylon! Watch as Dumbo circles the
tower. Mrs. Jumbo and Timothy Q. Mouse peer out of the illuminated windows at the base

of the pylon.

Congratulations

• Pylon

• Dumbo figure

• Support arm

• Switch

•Two green wires

• Owner’s Manual

• Service Center list

Dumbo Pylon Inventory

Wiring your Dumbo Pylon with a conventional power supply 3-4

Installing your Dumbo Pylon 5

Attaching the figure to your Dumbo Pylon 6

Operating your Dumbo Pylon with a conventional power supply 6

Operating your Dumbo Pylon with TrainMaster Command Control 7-8

Replacing the lamp in your Dumbo Pylon 9-11

Limited Warranty/Lionel Service 12

Table of contents

2

The following Lionel marks may be used throughout this instruction manual and are protected under
law. All rights reserved.

Lionel

®

, TrainMaster®, Odyssey®, RailSounds®, CrewTalk™, TowerCom™, DynaChuff™,

StationSounds

™

, Pullmor®, ElectroCoupler™, Magne-Traction®, CAB-1 Remote Controller®,

PowerMaster

®

, Lionel ZW®, ZW®, PowerHouse®, TMCC®, Lionelville™, Lockon

®

The name FasTrack®is used with permission from Pitsco, Inc.

W

iring your accessory is the first step in preparing for flight. The Dumbo Pylon will

operate best at 12-18 volts (AC), and it can be powered through track power with a
Lionel Lockon (available separately, 6-62900), or a FasTrack Accessory Power Wire (available
separately, 6-12053), OR through an accessory power supply. We recommend that you choose
a power supply that will allow you to increase or decrease the voltage to the accessory.
Changing the voltage allows you to control the speed at which the figure circles the pylon.
Figure 1 on page 4 illustrates the following procedure.

To make proper connections, you need the insulation at the ends of the wires to be stripped

back 1/4” to 3/8”. To strip the wires, use a pair of wire strippers.

Only an adult should perform this task! Always use care when stripping wires.

1. Attach one wire to the #1 terminal of the track Lockon, a FasTrack Accessory Power Wire,

OR the Power/A terminal on the accessory power supply. Connect it to one of the terminals
on the separate switch (included with this accessory).

2. Attach an additional wire to the other terminal on the switch. Connect the other end of this

wire to one of the spring-clip terminals at the bottom of the pylon.

To make the spring-clip terminal connections, press down on the “springy” top of
the terminal clip so that a metal loop is formed. Slide the bare end of the wire into
the exposed loop. Release pressure on the terminal clip, allowing the crimped metal
to pinch the end of the wire in the metal loop. Give a little tug on the wire to check
if the hold is secure.

3. Attach another wire to the #2 terminal of the track Lockon, a FasTrack Accessory Power

Wire, OR the Common/Ground/U terminal on the accessory power supply. Connect it
directly to one of the spring-clip terminals at the bottom of the pylon.

At this point, your accessory is wired for power. The next section explains how to operate this

accessory in a conventional (non-TrainMaster Command Control) environment.

Wiring your Dumbo Pylon with a conventional power supply

3

Caution!

Note!

4

Mounting
holes

Mounting
holes

Figure 1. Wiring for conventional operation

Wiring your Dumbo Pylon with a conventional power supply
(continued)

FasTrack Accessory Power Wire

U

U

A

A

UA

POWER
SUPPLY