Dirty hand 107036, 107079 Operation Manual

25-Ton & 30-Ton

Vertical/Horizontal Log Splitters

MODEL #’s 107036 (25-Ton) & 107079 (30-Ton)

Operation Manual

is safety alert symbol identies important safety messages in this manual. Failure to follow this important safety information

may result in serious injury or death.

Part # 107171 Rev A

For Service or Questions

Call 1-877-487-8275

720-287-5182

www.dirtyhandtools.com

Dirty Hand Tools® is a brand of

1100 W 120th Ave., Suite 600

Westminster, CO 80234 • 720-287-5182

Table of Contents

Important Safety Information .....................................................4

Intended Use ..............................................................................4

Personal Protective Equipment ..................................................4

Safety Decals ..............................................................................5

General Safety ............................................................................6

Preparation of the Log ...............................................................6

Work Area ................................................................................. 6

Operation of the Log Splitter .....................................................7

Repair and Maintenance Safety .. ................................................8

Hydraulic Safety .........................................................................8

Fire Prevention ...........................................................................9

Towing Safety ...........................................................................10

Unpacking & Assembly .............................................................11

Log Catcher Installation ..........................................................12

Operating Instructions ...............................................................13

Engine Oil Recommendations .................................................13

Starting Instructions .................................................................14

Towing ..................................................................................... 16

Maintenance .............................................................................16

Assembly Overview ....................................................................17

Log Catcher Assembly ..............................................................18

Tank & Wheel Assembly ..........................................................19

Tank & Tongue Assembly .........................................................20

Beam Bracket Assembly ............................................................21

Beam & Tank Assembly ............................................................22

Hydraulic Line Assembly ..........................................................23

Tank & Engine Assembly ..........................................................24

Pump & Engine Assembly ........................................................25

Beam Assembly .........................................................................26

Tongue Assembly ......................................................................27

Log Splitter Replacement Parts .................................................28

Hardware Kit .............................................................................29

Log Splitter Accessories .............................................................30

Specications & Warranty .........................................Back Cover

Important Safety Information

WARNING

WARNING: Read and understand the complete Operation Manual before assembling or using this product! Failure to comprehend and comply with warnings, cautions and instructions for assembly and operation could result in serious injury or death.

Do not permit children to operate this equipment at any time. Do not permit others that have not read and understood the complete Operation Manual to operate this equipment. Operation of power equipment can be dangerous. It is the sole responsibility of the operator to understand the assembly and safe operation of this product.

Call our customer service department at 720-287-5182, 1-877-487-8275, or visit www.dirtyhandtools.com if you have any questions or concerns about the safe operation of this equipment.

DANGER

INTENDED USE Do Not Use the log splitter for any purpose other than splitting wood, for which it was designed. Any other use is unauthorized and may result in serious injury or death.

PERSONAL PROTECTIVE EQUIPMENT

When operating this log splitter it is essential that you wear safety gear including goggles or safety glasses, steel toed shoes and tight ﬁtting gloves (no loose cuﬀs or draw strings). Always wear ear plugs or sound deafening headphones to protect against hearing loss when operating this log splitter.

CAUTION

Do Not wear loose clothing or jewelry that can be caught by

moving parts of the log splitter. Keep clothing and hair away from all moving parts when operating this log splitter.

Important Safety Information

OPERATING INSTRUCTIONS

CONTROL VALVE

OPERATION

For repair or service please call 1-877-487-8275

RETRACT

EXTEND

100212

WARNING

READ MANUAL BEFORE OPERATION

TO AVOID SERIOUS INJURY OR DEATH:

WEAR PROTECTIVE HEAD GEAR

WEAR GOGGLES OR PROTECTIVE EYEWEAR

WEAR NOISE DEAFENING HEADPHONES

WEAR PROTECTIVE FOOTWEAR

WEAR GLOVES

DO NOT USE HANDS TO CHECK FOR LEAKS

AVOID PINCH POINTS KEEP AWAY FROM MOVING PARTS

· STAY WITHIN DESIGNATED OPERATION ZONE

· KEEP PETS AND BYSTANDERS AWAY

· NEVER REACH OVER SPLITTER DURING OPERATION

· DO NOT OPERATE IN ENCLOSED SPACE

· KEEP BODY & CLOTHING AWAY FROM MOVING PARTS

· OPERATE ONLY WHEN COMPLETELY ALERT

1. PLACE LOG SPLITTER ON A STABLE, FLAT SURFACE

2. START ENGINE & ADVANCE THROTTLE TO MAXIMUM

3. PLACE LOG ON CRADLE AGAINST FOOT PLATE

4. MOVE VALVE HANDLE TOWARDS FOOT PLATE TO EXTEND THE WEDGE AND SPLIT THE LOG

5. MOVE VALVE HANDLE TOWARDS THE OPERATOR TO RETRACT THE WEDGE FROM THE LOG

NOTE: SPLIT WOOD IN DIRECTION OF THE GRAIN

Tank oil level should always be kept between the “MAX” and “MIN” lines indicated on the dipstick. Never fill the reservoir above the “MAX” line. Consult the Operation Manual for maximum system and operating fluid capacities. Select oil viscosity based on the outside

temperature at the time of operation in the table below

100207C

TO AVOID SERIOUS INJURY OR DEATH

● Read the Operation Manual on how to attach the coupler to the hitch ball and how to tow safely.

● Ensure the correct ball size is being used.

● Do not exceed hitch ball or coupler load limits.

● Attach and secure safety chains prior to towing.

● Do not exceed maximum towing speed of 45 mph.

● Avoid sharp turns and steep angles.

● Check tightness of the coupler before towing.

● Replace the hitch ball or coupler if damaged.

100208

WARNING

100204

DANGER

PINCH POINT

HAZARD

KEEP CLEAR

DURING

OPERATION

106047

HOT

SURFACE

DO NOT TOUCH

CAUTION

SAFETY DECALS

Make sure all safety warning decals are attached and in readable condition. Replace missing or defaced decals. Contact Dirty Hand Tools at 1-877-487-8275 for replacement decals.

Operation Decal Part # 100212

Warning Decal Part # 100208

Operator Zone Decal Part # 100399

Oil Level Decal Part # 100207

Hot Surface Decal Part # 106047

Pinch Point Decal Part # 100204

ATTENTION

START ENGINE,

CYCLE CYLINDER 3 - 4

TIMES, STOP ENGINE

ADD 32 - 64 FLUID OZ.

AW46 HYDRAULIC

FLUID BEFORE

OPERATION.

107163

Hydraulic Fluid Decal

Part # 107163

Important Safety Information

GENERAL SAFETY Failure to follow warnings, cautions, assembly and operation instructions in the Operation Manual may result in serious injury or death.

Read the Operation Manual before operation.

• Do not permit children to operate this equipment at any time.

Do not permit others that have not read and understood the complete Operation Manual to operate this equipment.

• Keep all people and pets a minimum of 10 feet away from the

work area when operating this log splitter. Only the operator is to be near the log splitter during use.

• Do not operate the log splitter when under the inﬂuence of

alcohol, drugs or medication.

• Do not allow a person who is tired or otherwise impaired or not

completely alert to operate the log splitter.

PREPARATION OF THE LOG

Both ends of the log should be cut as square as possible to prevent the log from rotating out of the splitter during operation.

Do not split logs greater than 25 in. in length.

DANGER

WORK AREA

• Do not operate the log splitter on icy, wet, muddy or otherwise

slippery ground. ONLY operate your log splitter on level ground.

Operating on a slope could cause the log splitter to roll over or logs to fall o of the equipment, which could result in injury.

• Do not operate the log splitter in an enclosed area. Exhaust

fumes from the engine contain carbon monoxide which can be harmful or deadly when inhaled.

• Do not move the log splitter over hilly or uneven terrain without

a tow vehicle or adequate help.

• Use a tire chock or block on the wheels to prevent movement of

the log splitter while in operation.

• Operate the log splitter in daylight or under good artiﬁcial light.

• Keep the work area free of clutter. Remove split wood from

around the log splitter immediately after each use to avoid potential tripping.

Important Safety Information

OPERATION OF THE LOG SPLITTER

Operate the log splitter from within the operation zone as shown in the diagrams below. e operator has the safest and most eﬃcient access to the control valve and the beam in these locations.

DANGER

Failure to operate the log splitter in this position can result in serious injury or death.

DANGER

• Make sure the operator knows how to stop and disengage the controls before operating.

• Do not place hands or feet between the log and splitting wedge during forward or reverse stroke. Serious injury or death could result.

• Do not straddle or step over the log splitter during operation.

• Do not reach or bend over the log splitter to pick up a log.

• Do not attempt to split two logs on top of each other.

• Do not attempt to cross split a log.

• Do not attempt to load your log splitter when the ram or wedge

is in motion.

• Use your hand to operate the control lever on the valve. Do not use your foot, a rope or any extension device.

• Do not move the log splitter while the engine is running.

• Never leave the equipment unattended while the engine is running. Shut oﬀ the engine even if you are leaving the log

splitter for a short period of time.

• Avoid contact with the muﬄer and other hot areas of the engine during operation or after running to prevent burns.

Important Safety Information

REPAIR AND MAINTENANCE

WARNING

• Do not operate the log splitter when it is in poor mechanical condition or in need of repair. Frequently check that all nuts,

bolts, screws, hydraulic ﬁttings and hose clamps are tight.

• Do not alter the log splitter in any manner. Any alteration will void the warranty and could cause the log splitter to be unsafe to operate. Perform all recommended maintenance procedures before using the log splitter. Replace all damaged or worn parts immediately.

• Do not tamper with the engine to run it at excessive speeds. e maximum engine speed is preset by the manufacturer and is within safety limits. See Kohler engine manual.

• Remove the spark plug wire before performing any service or repair on the log splitter.

• Always check the level of hydraulic oil and engine oil before operation.

• Replacement parts must meet manufacturer’s speciﬁcations.

HYDRAULIC SAFETY

e hydraulic system of the log splitter requires careful inspection along with the mechanical parts. Be sure to replace frayed, kinked, cracked or otherwise damaged hydraulic hoses or hydraulic components.

• Check for hydraulic uid leaks by passing a piece of paper or cardboard underneath or over the area of the leak. Do not check

for leaks with your hand. Fluid escaping from the smallest hole, under pressure, can have enough force to penetrate the skin causing serious injury or death.

• Seek professional medical attention immediately if injured by escaping hydraulic uid. Serious infection or reaction can

develop if medical treatment is not administered immediately.

• Relieve all pressure by shutting oﬀ the engine and moving the valve control handle back and forth should it become necessary to loosen or remove any hydraulic ﬁtting.

• Do not remove the cap from the hydraulic tank or reservoir while the log splitter is running. e tank could contain hot oil under

pressure which could result in serious injury.

• Do not adjust the hydraulic valve. e pressure relief valve on the log splitter is preset at the factory. Only a qualied service

technician should perform this adjustment.

Important Safety Information

FIRE PREVENTION

CAUTION

• Do not operate the log splitter near an open ﬂame or spark.

Hydraulic oil and gasoline are ammable and can explode.

• Do not ﬁll the gas tank while the engine is hot or running.

Allow the engine to cool before refueling.

• Do not smoke while operating or refueling the log splitter. Gas

fumes can easily explode.

• Refuel the log splitter in a clear area with no gas fumes or spilled

gas. Use an approved fuel container. Replace the gas cap securely. If gasoline has spilled, move the log splitter away from the area of the spill and avoid creating any source of ignition until the spilled gas has evaporated.

• Keep a Class B ﬁre extinguisher on hand when operating this log

splitter in dry areas as a precautionary measure against possible ﬂying sparks.

• Drain the fuel tank prior to storage to avoid the potential ﬁre

hazard. Store gasoline in an approved, tightly sealed container. Store the container in a cool, dry place.

• Turn the fuel shut oﬀ valve on the engine to the “OFF” position

before towing the log splitter. Failure to do so may result in ﬂooding the engine.

CAUTION

IMPORTANT NOTE:

is log splitter is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in eﬀective working order by the operator. In the state of California a spark arrester is required by law. Other states have similar laws.

Federal laws apply on federal lands. A spark arrester muﬄer (optional by manufacturer) is available as an accessory at your nearest engine dealer. Always check the legal requirements in your area.

Important Safety Information

CAUTION

TOWING SAFETY

• Check all local and state regulations regarding towing, licensing,

and lights before towing your log splitter.

• Check before towing to make sure that the log splitter is correctly and securely attached to the towing vehicle and that the safety chains are secured to the hitch or bumper of the vehicle with enough slack to allow turning. Always use a Class I, 2” ball with this log splitter.

• Do not carry any cargo or wood on the log splitter.

• Do not allow anyone to sit or ride on the log splitter.

• Disconnect the log splitter from the towing vehicle before

operating it.

• Use care when backing up with the log splitter in tow to avoid jack-kniﬁng. Allow for added length of the log splitter when turning, parking, crossing intersections and in all driving situations.

• Do not exceed 45 mph when towing your log splitter. Towing the log splitter at speeds higher than 45 mph could result in loss of control, damage to the equipment, serious injury or death. Adjust towing speed for terrain and conditions. Be extra cautious when towing over rough terrain especially railroad crossings.

Unpacking & Assembly

List of tools needed for assembly:

• Needle nose pliers • Scissors • Box Cutter or knife

• (2) 17mm wrenches • (2) 19mm wrenches

IMPORTANT: e hydraulic tank is pre-lled with AW46 hydraulic uid and the engine is pre-lled with 10W30 engine oil at the factory.

WARNING

Two (2) people may be required for assembly

1. Cut and remove the box and additional packaging.

2. Cut and remove banding using scissors.

3. Remove engine guard by removing the lynch pin underneath the engine (see arrow). Recycle engine guard.

4. Cut and remove bag around the tow coupler, cut zip tie and lower tongue . Extend tongue stand .

5. Remove bolts, washers, and nuts from tongue mount bracket on tank.

6. Slide tongue into the mounting bracket , aligning the two holes in the tongue with the two holes in the bracket and secure with hex bolt , washer , lock washer and hex nut , in two places.

7. Lower beam into the horizontal position and secure beam latch . Two people may be required to complete operation.

8. Attach valve handle into operational position and secure with clevis pin and cotter pin .

10 11

9. Remove log splitter from metal pallet and recycle pallet.

Two people may be required to complete operation.

10. Check all ﬁttings and hardware for tightness.

Item Description Qty.

1 Metal Pallet 1 2 Engine Guard 1 3 Tongue & Stand Assembly 1 4 Tongue Stand 1 5 Hex Bolt, M12 x 1.75 x 1.10mm, G8.8 2 6 Flat Washer, M12 4 7 Lock Washer, M12 2 8 Hex Nut, M12 x 1.75, G8.8 2 9 Valve Handle 1 10 Clevis Pin, 1/4 in. x 1/2 in. 1 11 Cotter Pin, 1/16 in. x 1/2 in. 1 12 Detent Valve 1 13 Beam & Cylinder Assembly 1 14 Beam Lock Bracket 1 15 Tongue Mount Bracket 1

153

Log Catcher Installation (30-Ton)

NOTE: e 25-Ton Log Splitter does not come with a log catcher, which is available as an accessory.

1. Rotate Beam & Cylinder Assembly down from upright

position and lock in place with the release pin.

2. Install the Log Catcher Assembly 1 with Hex Bolts, M10 x

1.5 x 30mm Hex Nut, M10 x 1.5

6; in 2 places. Tighten hex nuts securely with a 17mm socket

wrench and tighten button screws with 6mm hex key wrench.

2; Flat Washer, M10 3; Lock Washer, M10 4;

5; and Button Screw, M10 x 1.5 x 30mm

Item # Part # Description Qty.

1 100157 Log Catcher Grate 1

2 100165 Hex Bolt, M10 x 1.5 x 30mm, G8.8 2

3 100161 Flat Washer, M10 6

4 100089 Lock Washer, M10 4

5 100009 Hex Nut, M1 x 1.5, G8.8 4

6 100064 Button Screw, 2 M10 x 1.5 x 30mm, G8.8

Operating Instructions

DANGER

Do not permit children to operate this equipment at any time. Do not permit others that have not read and understood

the complete Operation Manual to operate this equipment. Operation of power equipment can be dangerous. It is the sole responsibility of the operator to understand the assembly and safe operation of this product.

Call our customer service department at 720-287-5182, 1-877-487-8275, or visit www.dirtyhandtools.com if you have any questions or concerns about the safe operation of this equipment.

CAUTION

e hydraulic reservoir should be lled with hydraulic uid

and the engine should be lled with engine oil

before starting or operation.

STEP 1: Add approximately 4 gallons of hydraulic ﬂuid. e

remaining hydraulic ﬂuid will be added after the cylinder is cycled. AW32 or AW46 hydraulic oil is recommended. Automatic transmission ﬂuid can be substituted instead of hydraulic oil when temperatures are below 32°F. Use only clean oil and take care to prevent dirt from entering the hydraulic reservoir.

ENGINE OIL RECOMMENDATIONS

Use 4-stroke automotive detergent oil. SAE 10W-30 is recommended for general use. Refer to the SAE Viscosity Grades chart in your engine owner’s manual for average temperature ranges. e engine manufacturer recommends using API SERVICE Category SE or SF oil. e engine oil capacity is 20 oz. for Kohler SH265 (22-Ton/27-Ton) and 40 oz. for Kohler CH395 (35-Ton). Always check oil level before starting the engine and keep level full.

Operating Instructions

Step 2: After the hydraulic reservoir and the engine crankcase

are ﬁlled with oil, start the engine. e hydraulic pump is self-priming. With the engine running, move the hydraulic valve lever toward the foot plate. is will cause the cylinder to extend and expel air. When the cylinder is fully extended, retract it. Repeat this procedure several times. An erratic movement of the cylinder indicates that there is still air in the system. Add about 1.0 to 1.5 gallons of hydraulic ﬂuid. Five gallons will register just above the top ﬁll line on the dip stick. e total capacity of the entire hydraulic system is 6.5 gallons with 5 gallons of hydraulic ﬂuid the minimum required to operate.

NOTE: If the tank is overlled it will expel oil from the breather cap when the cylinder is retracted. Cycle the cylinder again until it has a constant speed which indicates that all air has been expelled.

STARTING INSTRUCTIONS NOTE: Refer to the Engine Owner’s Manual for complete

information on starting, maintenance and troubleshooting.

1. Move the fuel valve lever to the ON position.

2. To start a cold engine, move the choke lever to the CLOSE

position. To restart a warm engine, leave the choke lever in the OPEN position.

3. Move the throttle lever away from the SLOW position,

about 1/3 of the way toward the FAST position.

4. Turn the engine switch to the ON position.

5. Pull the starter grip until you feel resistance, then pull

briskly. Return the starter grip gently.

6. If the choke lever has been moved to the CLOSE position

to start the engine, gradually move it to the OPEN position as the engine warms up.

7. To stop the engine in an emergency, simply turn the engine

switch to the OFF position. Under normal conditions, move the throttle lever to the SLOW position and then turn the engine switch to the OFF position. en turn the fuel valve lever to the OFF position.

For further information on starting and stopping the engine, refer to your engine owner’s manual.

Operating Instructions

CAUTION

CAUTION: Turn Fuel Shut O Valve to the “O” position before towing to avoid ooding the engine.

NOTE: e engine‘s maximum speed is factory preset at 3600

RPM as the no load speed. e throttle should be set at the maximum speed for wood splitting to reach the horsepower required for the pump.

WARNING

WARNING: Review safety information related to operation of

the log splitter on pages 4-10 of this manual. Make sure that you have the recommended personal protective equipment described on page 4.

1. Set up the log splitter in a clear, level area and block the wheels. Make sure that the suction port on the tank is always on the lower side of the log splitter.

2. For horizontal operation place a log on the beam against the foot plate. Make sure the log is securely on the foot plate and against the beam. To split wood in the vertical position, release the pin on the beam latch located on the front end of the beam. Carefully tilt the beam up until the foot plate is sitting squarely on the ground and the log splitter is stable. Place the log on the foot plate against the beam. When the beam is returned to the horizontal position make sure the beam latch is securely locked down.

3. With the engine running, depress the valve handle so that the cylinder will drive the wedge into the log. Extend the cylinder until the log splits or to the end of its stroke. If the log has not completely split after the cylinder has reached the end of its extension, retract the cylinder.

IMPORTANT: Leaving the valve in the “actuate” position at the end of the stroke may damage the pump. Always use extra care when splitting logs with unsquare ends.

Store manuals in the Manual Cannister attached to the tongue of the log splitter or le in a safe place for future reference.

Operating Instructions

NOTE: For operation in wooded areas, obtain a spark arrestor

for the exhaust system. See the engine operating and maintenance manual and check with your authorized service center. See also Fire Prevention on page 9 of this manual.

IMPORTANT: To extend the life of the hydraulic cylinder avoid bottoming out the wedge plate to the foot piece. To conform with industry safety recommendations the wedge stops 1/2 inches from the end of the stroke.

TOWING

is log splitter is equipped with pneumatic tires, a Class I coupler (2 in. diameter ball required) and safety chains. Before towing, the safety chains must be secured to the hitch or bumper of the vehicle. Local regulations should be checked regarding licensing, lights, towing, etc. Turn fuel shut oﬀ valve on the engine to the “Oﬀ ” position prior to towing. Failure to do so may result in ﬂooding the engine. Do not exceed 45 mph when towing this log splitter. See also Towing Safety on page 10 of this manual.

MAINTENANCE

1. Consult the operating and maintenance instructions of the engine manufacturer for engine care and maintenance.

2. Always check the oil level of the hydraulic reservoir before operation. Operating the log splitter without an adequate oil supply will cause severe damage to the pump.

3. Change the oil ﬁlter after the ﬁrst 25 hours of operation. ere after change the oil ﬁlter every 100 hours or seasonally, whichever comes ﬁrst.

4. To drain the hydraulic oil, loosen the clamp on the hose coming from the ﬁtting on the bottom of the tank. It is located just to the right of the oil ﬁlter.

5. If the wedge becomes dull or nicked, it can be removed and sharpened. Remove the bolt that connects the wedge to the cylinder. e hose from the valve may need to be removed. Carefully lift the cylinder to allow the wedge to slide forward. e wedge can now be lifted oﬀ and sharpened.

6. Clean the breather cap after 25 hours of operation. Clean it more often when operated in dusty conditions. To clean, remove the breather cap from the tank and ﬂush with kerosene or liquid detergent to remove the dirt.

7. See Repair and Maintenance on page 8 of this manual.

8. All replacement parts must meet manufacturer’s speciﬁcations.

Assembly Overview

Item # Part # Description Qty.

1 107164 Tank & Engine Assembly (25-Ton) 1 107165 Tank & Engine Assembly (30-Ton)

2 100065 Tongue & Stand Assembly 1

3 107166 Beam & Cylinder Assembly (25-Ton) 1 107167 Beam & Cylinder Assembly (30-Ton)

4 100062 Wheel/Tire Assembly, 4.80 x 8 in. 2

5 100150 Beam Lock Bracket 1

6 100087 Beam Pivot Bracket 1

7 101391 Log Catcher Assembly (25-Ton)* 1 100173 Log Catcher Assembly (30-Ton)

* Item not included with Model 107036 (25-Ton) **Item not shown

Log Catcher Assembly

101391

Log Catcher Assembly

For 25-Ton

100173

Log Catcher Assembly

For 30-Ton

Item # Part # Description Qty.

1 100929 Log Catcher Grate 1

2 100934 Support Arm, Large Right 1

3 100933 Support, Right 1

4 100930 Support Arm, Left 1

5 100931 Support Arm, Large Left 1

6 100165 Hex Bolt, M10 x 30mm 8

7 100009 Hex Nut, M10 8

8 100089 Lock Washer, M10 8

9 100181 Flat Washer, M12 8

Item # Part # Description Qty.

1 100157 Log Catcher Grate 1

2 100154 Log Catcher Support Plate 2

3 100155 Log Catcher Mount, Lower 2

4 100152 Log Catcher Mount, Upper 2

5 100165 Hex Bolt, M10 x 30mm 8

6 100089 Lock Washer, M10 10

7 100009 Hex Nut, M10 10

8 100161 Flat Washer, M10 12

9 100064 Button Head Screw, M10 x 30mm 2

Tank and Wheel Assembly

Item # Part # Description Qty.

1 107164 Tank & Engine Assembly (25-Ton) 1 107165 Tank & Engine Assembly (30-Ton)

2 100062 Wheel/Tire Assembly, 4.80 x 8 in. 2

3 100142 Flat Washer, 3/4 in. 2

4 100140 Castle Nut, 3/4-16, Clear Zinc 2

5 100143 Cotter Pin, 1/8 in. x 1-1/2 in. 2

6 100063 Hub Cap 2

7 100162 Hub Cap Tool 1

Tank and Tongue Assembly

Item # Part # Description Qty

1 107164 Tank & Engine Assembly (25-Ton) 1 107165 Tank & Engine Assembly (30-Ton)

2 100065 Tongue & Stand Assembly 1

3 100200 Hex Bolt M12 x 1.75 x 1.10mm, G8.8 2

4 100181 Flat Washer, M12 10

5 100023 Lock Washer, M12 8

6 100022 Hex Nut, M12 x 1.75, G8.8 8

Beam Bracket Assembly

Item # Part # Description Qty.

1 107166 Beam & Cylinder Assembly (25-Ton) 1 107167 Beam & Cylinder Assembly (30-Ton)

2 100150 Beam Lock Bracket 1

3 100087 Beam Pivot Bracket 1

4 100021 Hex Bolt, M12 x 1.75 x 35mm, G8.8 7

5 100181 Flat Washer, M12 10

6 100023 Lock Washer, M12 8

7 100022 Hex Nut, M12 x 1.75, G8.8 8

Beam and Tank Assembly

Item # Part # Description Qty.

1 100131 Hitch pin, 5/8 in. x 6 1/4 in. 1

2 100132 R-Clip, 1/8 in., Fits 1/2 in. to 3/4 in. 1

Hydraulic Line Assembly

Item # Part # Description Qty.

1 100136 Hydraulic Hose, 1/2 in. x 56 in. 1

2 100137 Hydraulic Hose, 1/2 in. x 38 in. 1

Tank and Engine Assembly

Item # Part # Description Qty.

1 107168 Tank with Decals (25-Ton) 1 107169 Tank with Decals (30-Ton) 2 107170 Engine/Pump Assembly 1 3 100129 Hex Bolt, M8 x 1.25 x 45MM, G8.8 4 4 100130 Flat Washer, M8 8 5 100128 Hex Nut, Nylock, M8 x 1.25, G8.8 4 6 100105 Suction Filter 1 7 100111 Fitting, 3/4 NPT to 1 in. Tube 1 8 100112 Fitting, M 3/4 NPT, M 3/4 NPT 1 9 100117 Filter Base, 3/4 NPT, 1-12 UNF 1 10 100118 Elbow M 3/4 NPT, F 1/2 NPT 1 11 100116 Hydraulic Oil Filter (DHT logo) 1 100448 Hydraulic Oil Filter (Generic logo) 1 12 100138 Hose Clamp, 15/16 in. to 1-1/4 in. 2 13 100135 Suction Line Tube, Wire Reinforced 1 14 100137 Hydraulic Hose, 1/2 in. x 38 in. 1 15 100136 Hydraulic Hose, 1/2 in. x 56 in. 1 16 100131 Hitch Pin, 5/8 in. x 6 1/4 in. 1 17 100132 R-Clip, 1/8 in., 1/2 in. to 3/4 in. 1

18 100110 Vent Cap Assembly 1

Pump and Engine Assembly

Item # Part # Description Qty.

1 100121 Engine, Kohler SH265 1

2 100159 Bar, Key Stock, SQ 3/16 in. x 1-1/2 in. 1

3 100127 Lock Washer, M8 4

4 100486 Hex Bolt, 5/16 in.-24 x 1.25 in., Z5 4

5 100126 Hex Bolt, M8 x 1.25 x 30mm, G8.8 4

6 100128 Hex Nut, Nylock, M8 x 1.25, G8.8 4

7 107133 Pump, 2 Stage, 15 GPM 1

8 100397 Jaw Coupler Assembly, 1/2 in. Bore, L090 1

9 100016 Pump Mount, 92mm BC 1

10 100124 Jaw Spider Coupler, L090 1

11 100398 Jaw Coupler Assembly, 3/4 in. Bore 1

Beam Assembly

Item # Part # Description Qty.

1 100832 Beam (25-Ton) 1 106804 Beam (30-Ton) 2 104156 Cylinder, 4.33 in., F 1/2 NPT (25-Ton) 1 104134 Cylinder, 4.72 in., F 1/2 NPT (30-Ton) 3 101259 Wedge, 7 in. (25-Ton) 1 100035 Wedge, 8 in. (30-Ton) 4 100030 Nipple, 1/2 NPT, 1/2 NPT 1 5 100034 Valve, Adjustable Detent, 3500 PSI 1 6 100029 Elbow, 1/2 NPT, 1/2 Flare Tube 2 7 100028 Tube, 1/2 OD, Flared, 3/4-16 in. Nuts 1 8 100033 Clevis Pin Assembly, 1 in. OD, w/clips 1 9 100041 Hex Bolt, M12 x 1.75 x 75mm, G8.8 1 10 100021 Hex Bolt, M12 x 1.75 x 35mm, G8.8 4 11 100181 Flat Washer, M12 4 12 100023 Lock Washer, M12 5 13 100022 Hex Nut, M12X1.75, G8.8 5 14 100043 Elbow M 3/4 NPT TO F1/2 NPT 1

15 100042 Fitting, 45 16 100205 Stripper, RT (30-Ton only) 1 17 100206 Stripper, LT (30-Ton only) 1

, M 3/4NPT TO F1/2NPT 1

Tongue Assembly

Item # Part # Description Qty.

1 100050 Tongue 1

2 100061 Ball Coupler Assembly, 2 in. 1

3 100080 Tongue Stand 1

4 100084 Manual Canister 1

5 100085 Hex Bolt, M6 x 1.0 x 20mm, G8.8 3

6 100445 Fender Washer, M6 3

7 100070 Shim, OD 75mm, ID 64mm x 1mm 1

8 100069 Retaining Ring, External, 63mm Shaft 1

9 100066 Hex Bolt, M10 x 1.5 x 100mm, G8.8 1

10 100161 Flat Washer, M10 4

11 100068 Hex Nut, Nylock, M10 x 1.5, G8.8 2

12 100067 Hex Bolt, M10 x 1.5 x 120mm, G8.8 1

13 100077 Flat Washer, 1/2 in. 2

14 100047 Safety Chain 2

25/30 Ton Log Splitter Replacement Parts

Vent Cap

100110

(not shown)

Detent Valve

100034

Tire & Wheel

100062

Hub Cap

100063

Suction Filter

100105

(not shown)

Log Catcher

100179 (30 Ton) 101392 (25 Ton)

Stripper Plate

Left

100206

Stripper Plate

Right

100205

4-Way Wedge

100349

(optional)

Cylinder, 4.33”

104156

(25 Ton)

Cylinder, 4.72”

104134

(30 Ton)

Cylinder Tube

100028

Hose, 56”

100136

(lter to valve)

Manual Cannister

100084

Ball Coupler

100061

Retaining Ring

100069

(not shown)

Jack End Cap

100074

Tongue Stand

100080

Filter Base

Jaw Coupler, 1/2”

100397

100117

Oil Filter

100116

Spider Coupler

100124

Beam (25 Ton) 100832 Beam (30 Ton) 100015

Stripper Plates (set) 101707

Wedge (8” ) 100035 Hydraulic Tank (22/27) 100103

Suction Tube

100135

Jaw Coupler, 3/4”

100398

For other part numbers including hardware and other components, see the Operation

or contact Service at 1-877-487-8275 or info@frictionlessworld.com

Pump 15gpm

107133

45° Hose Fitting

100042

Pump Mount

100016

Elbow Hose

Fitting

100043

Hose, 38”

100137

(pump to valve)

Nipple Fitting

100030

Elbow Fitting

100029

(2 Places)

Manual

Hardware Kit - Part #100163

Item # Part # Description Qty.

1 100166 Hardware Kit 1

2 100150 Beam Lock Assembly 1

3 100087 Beam Pivot Bracket Plate 1

4 100063 Hub Cap 2

5 100162 Hub Cap Tool 1

6 100143 Cotter Pin, 1/8 in. x 1-1/2 in. 2

7 100140 Castle Nut, 3/4 in.16 2

8 100142 Flat Washer, 3/4 in. 2

9 100021 Hex Bolt, M12 x 1.75 x 35mm, G8.8 6

10 100023 Lock Washer, M12 8

11 100022 Hex Nut, M12 x1.75, G8.8 8

12 100164 Manual, 22/27/28/35 Ton 1

13 100200 Hex Bolt, M12 x 1.75 x 110mm, G8.8 2

14 100181 Flat Washer, M12 10

Log Splitter Accessories

4-Way Wedge System

e 4-Way Wedge System replaces the existing wedge on 25 & 30-Ton Log Splitters converting them to a four way splitter for fast quarter splitting of logs. System includes stripper plates, 2-way wedge and all hardware. Fits part #’s 106264 and 106265.

Log Splitter Cover

Weather-proof heavy duty PVC coated polyester cover easily slips over log splitter for year round outdoor protection. Water, UV and mildew resistant with convenient drawstring for fast use. Use with 25 and 30-Ton Log Splitters.

Log Catcher Kit

Quickly attaches to 25 and 30-Ton Log Splitters. Catches the split log as the cylinder and wedge retract for easier operation.

SKU/Part# Description Specication Weight

100349 4-Way Wedge System 8.66” L x 8.86” W x 8.67” H 55 Lbs. 100506 Log Splitter Cover 90” L x 48” W x 40” H 10 Lbs. 101392 Log Catcher Assembly (25-Ton) 20.75”L x 12” W x 6”H (installed) 15 Lbs. 100179 Log Catcher Assembly (30-Ton) 20.75”L x 12” W x 6”H (installed) 15 Lbs.

Part # 101392

(For 25-Ton)

Part # 100179

(For 30-Ton)

Notes

Specications Vertical/Horizontal Log Splitters

SKU/Part No. 107036 (25-Ton) 107079 (30-Ton)

Maximum Splitting Force 25-Tons

30-Tons

Engine2 6.5 HP 196CC3 6.5 HP 196CC Kohler SH265 Kohler SH265

Maximum Log Length 25” 25”

Cycle Time, Down & Back 11.2 Seconds

14.3 Seconds Cylinder 4.33” Dia. x 24” Stroke 4.72” Dia. x 24” Stroke Pump, Two Stage 15 GPM 15 GPM Wedge, Heat-Treated Steel 7” High 8” High Beam 7” Foot Plate 8” Foot Plate

Hydraulic Capacity 6.5 Gallons Max.

6.5 Gallons Max.

Shipping Weight (with Fluids) 510 Lbs. 550 Lbs.

Common Specications

Valve Auto Return with Adjustable Detent Wheels D.O.T. Approved 16” O.D. Road Tires Coupler 2” Ball with Safety Chains Optional Accessories 4-Way Wedge, Fenders, Storage Cover Replacement Filters Part # 100116 Return Filter Part # 100105 Suction Screen Warranty 3 Year / 2 Year / 1 Year, Limited

Tonnage and cycle times may vary dependent upon mechanical and environmental conditions.

EPA/CARB Approved/50 State Legal

As rated by engine manufacturer

Minimum Operational Capacity is 5 Gallons of Hydraulic Fluid

Minimum Operational Capacity is 6.5 Gallons of Hydraulic Fluid

Warranty

IMPORTANT NOTICE

We, the manufacturer, reserve the right to change the product and/or speciﬁcations in this manual without notiﬁcation. e manual is for information usage only and the pictures and drawings depicted herein are for reference only.

Warranty Repair and Service

Do not return this product to the store for warranty issues or repair. Call our customer service department at 720-287-5182, 1-877-487-8275, or visit www.dirtyhandtools.com for the location of the nearest service center.

Record the information below for future reference.

Model No. Serial No. Date of Purchase Place of Purchase

Dirty Hand Tools® is a brand of

1100 W 120th Ave., Suite 600

Westminster, CO 80234 • 720-287-5182

For Service or Questions

Call 1-877-487-8275

720-287-5182

www.dirtyhandtools.com

Dirty hand 107036, 107079 Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual