Dirt Devil M084610, R084600 Owner's Manual

For quick reference, please record your vacuum information below.
Model #: Mfg.
Code:
(Mfg. code located on the lower backside of cleaner)
Español - página E1
©2004 All rights reserved #1-113191-000
• Please read these instructions carefully before using your Lightweight Vacuum.
• Let us help you put your vacuum together or answer any questions, call:
1-800-321-1134 (USA & Canada)
www.dirtdevil.com
WARNING:
Cleaner assembly may include small parts. Small parts can present a choking hazard.
OWNER’S MANUAL
Operating and Servicing
Instructions
Warranty Registration
• Online at: www.dirtdevil.com
• Mail: Royal Appliance Mfg 7005 Cochran Rd. Glenwillow, Ohio 44139
THIS VACUUM CLEANER IS INTENDED FOR HOUSEHOLD USE ONLY.
IMPORTANT SAFETY INSTRUCTIONS
When you use an appliance, basic precautions should always be followed, including the following:
• READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
• ALWAYS FOLLOW THESE SAFETY INSTRUCTIONS.
• BRING VACUUM CLEANER TO UPRIGHT POSITION WHEN USING THE HOSE AND ATTACHMENTS.
• DO NOT LEAVE VACUUM CLEANER UNATTENDED WHEN PLUGGED IN.
• REGULARLY CHECK THE FILTER TO CLEAN OR REPLACE.
• WARNING: FULLY ASSEMBLE CLEANER BEFORE OPERATING.
• WARNING: DO NOT USE SHARP OBJECTS TO CLEAN OUT THE HOSE SINCE THEY COULD CAUSE DAMAGE.
• OCCASIONALLY REMOVE BRUSH AND CLEAN DEBRIS FROM END CAPS TO KEEP BRUSH ROTATING SMOOTHLY.
• WARNING: THE CORDS, WIRES, AND/OR CABLES SUPPLIED WITH THIS PRODUCT CONTAINS CHEMICALS, INCLUDING LEAD OR LEAD COMPOUNDS, KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USING.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:
• Do not leave appliance when plugged in. Unplug from outlet when not in use and before ser
vicing.
• Do not use outdoors or on wet surfaces. Electrical shock could occur.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center for inspection. Call 1-800-321-1134 for the nearest service center.
• Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any objects into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
Do not pick up an
ything tha
t is burning or smoking, such as cigarettes, matches,
or hot ashes.
2
WARNING:
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
Your cleaner contains a thermal protective device to shut off the motor to avoid overheating. If this happens, turn switch off and unplug the cleaner. Inspect the exhaust, inlet,hose, and filters for any blockage. Empty the dirt container and clean filters. After approximately 30 minutes the motor will have cooled and the vacuum will be ready to use.
NOTE: The cleaner
must remain unplugged during the 30 minute cooling period.
3
• Do not use without dirt container and filters in place.
• Turn off all controls before unplugging.
• Look on your vacuum cleaner and follow all label and marking instructions.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
• Keep the vacuum cleaner on the floor. Only the hand-held vacuum cleaners may be set on furniture.
• Vacuum cleaner must be in the upright position to lift the rotating brush off the carpet when doing above floor cleaning.
• Do not use an extension cord with this vacuum cleaner.
• Store the vacuum cleaner indoors. Put the vacuum cleaner away after use to prevent tripping accidents.
• Using improper voltage may result in damage to the motor and possible injury to the user. Proper voltage is listed on the cleaner plate.
SAVE THESE INSTRUCTIONS
CONGRATULATIONS
You are now the proud owner of a Dirt Devil®. We trust your new purchase will bring you many years of satisfaction.
Our company has designed and developed this product with you in mind. We are very proud of our products and hope that you are equally satisfied
with their quality and performance. Thank you for your support of Dirt Devil
®
products.
Visit our website at www.dirtdevil.com
TABLE OF CONTENTS
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2, 3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5
How to Assemble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6
How To Operate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6
Dirt Container & Filter: Removal & Replacement . . . . . . . . . . . . . Page 7
Belt or Brushroll: Removal & Replacement . . . . . . . . . . . . . . . . . Page 8
Troubleshooting Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 9
LIMITED WARRANTY
To the consumer, Royal Appliance Mfg. Co. warrants this vacuum cleaner to be free of defects in material or workmanship commencing upon the date of the original purchase. Refer to your vacuum cleaner carton for the length of warranty and save your original sales receipt to validate start of warranty period.
If the vacuum cleaner should become defective within the warranty period, we will repair or replace any defective parts free of charge. The complete machine must be delivered prepaid to any ROYAL®Authorized Sales & Warranty Service Station. Please include complete description of the problem, day of purchase, copy of orig­inal sales receipt and your name, address and telephone number. If you are not near a Warranty Station, call the factory for assistance at USA & Canada: 1-800-321-1134. Use only genuine Royal®replacement parts.
The warranty does not include unusual wear,damage resulting from accident or unreasonable use of the vacuum cleaner. This warranty does not cover brushes, bags, flat belts, filters and bulbs. This warranty does not cover unauthorized repairs. This warranty gives you specific legal rights and you may also have other rights (Other rights may vary from state to state in the USA).
4
IMPORTANT: USE ONLY GENUINE ROYAL®REPLACEMENT PARTS. NO
TE: RETURN W
ARRANTY C
ARD TO REGISTER Y
OUR CLEANER
BACK VIEWFRONT VIEW
FRONT VIEW
1. Handle grip
2. Cord guide
3. Dirt container release button
4. On/Off switch
5. Carry handle
6. Filter
7. Dirt container
8. Nozzle
BACK VIEW
9. Telescopic handle
10. Telescopic handle release button
11.
Upper cord wrap with quick cord release
12. Long power cord
13. Lower cord wrap with quick cord release
14. Wheels
15. Lower hose/Clog clean-out
5
FEATURES
1
2
3
4
5
6
7
8
9
10
11
12
13
14
14
15
BUTTON
6
HOW TO ASSEMBLE
HOW TO OPERATE
Insert handle into body of cleaner.
Push down firmly until handle locks into place.
1.
2.
For storage, press the telescopic handle release button (Diagram 1) on the back of the cleaner and push handle down (Diagram 1a).
For regular use, push the telescopic handle release button (Diagram 1) and pull handle up (Diagram 1a).
FOR STORAGE FOR REGULAR USE
1.
1a.
HANDLE
DOWN
1.
1a.
BUTTON
Plug cord into electrical outlet. Turn cleaner on by pressing the on/off switch located on the top of unit.
ON/OFF SWITCH
1.
HANDLE RELEASE
1.
Pull back handle to tilt back. Press on the front of nozzle if needed.
CORD RELEASE
Turn the Quick Cord Release for easy cord removal. Store cord in cord guide (see “features”, Diagram 2 for location) to keep out of the way while vacuuming.
1.
FLOOR/CARPET CLEANING
1.
Move the handle and adjust it to the desired position for (a) operating the cleaner, and (b) lowering handle to clean under furniture.
a
b
CARRY HANDLE
1.
Use the carry handle located on the top of the dirt container lid to move the cleaner from room to room.
DIRT CONTAINER & FILTER: REMOVAL & REPLACEMENT
7
WARNING: TO REDUCE THE RISK OF INJURY FROM MOVING PARTS - UNPLUG BEFORE REMOVING OR REPLACING
FILTER.
NOTE: For best performance, replace filter yearly. Please use reminder label located on filter cap to record replacement date.
F2
FILTER TYPE
For F2 filter replacement, please call 1-800-321-1134 or visit our website at www.dirtdevil.com to locate a dealer nearest you.
UNLOCK
Depress button on top of dirt container lid to remove dirt container.
Remove lid by grasping handle on dirt container lid and turn counter clockwise.
2.
Hold the dirt container and grasp the top of the filter. Twist the filter counter clockwise to unlock (Diagram 3a). Pull the filter up and out.
1.
3.
3a.
Return dirt container to base of unit.
Line up arrow on dirt container with lock/ unlock arrows on dirt container lid for proper alignment. Turn clock­wise to lock lid in place.
UNLOCK
LOCK
Clean filter and empty dirt container completely. See “Regular Maintenance” note below for instructions on cleaning the filter.
Return lid to dirt container.
Return filter to dirt container. Twist filter clockwise to lock into position.
5.
7.
4.
*REGULAR MAINTENANCE: Each time the dirt container is emptied, the filter should be cleaned. Tap the filter firmly
against the inside of a trash can until the dirt stops falling from the filter. (Filter will be discolored after use, this will not affect the filter’s performance.) Do not brush the filter. The cleaning instructions may vary depending on the dirt conditions. In some cases, more or less cleaning of the filter may be required.
6.
8.
8
BELT OR BRUSHROLL: REMOVAL & REPLACEMENT
BELT STYLE
15
For Belt Style 15 replacements, please call 1-800-321-1134 or visit our website at www.dirtdevil.com to locate a dealer nearest you.
TOOL REQUIRED: PHILLIPS SCREWDRIVER WARNING:TO REDUCE THE RISK OF INJURY FROM MOVING PARTS - UNPLUG BEFORE CHANGING BELT OR
BRUSHROLL.
Lift and remove brushroll. Dispose of old belt.
Slide belt onto motor shaft. Place new belt in area of
brushroll without bristles.
TO REMOVE BELT
Lay cleaner flat and flip cleaner to
expose nozzle base. Base should lay flat and face up. To remove nozzle guard, use Phillips screwdriver to remove the six (6) screws. Arrows show location of screws.
Slide belt off motor shaft.Tilt rollers up and away from the base of the cleaner as you remove the nozzle guard
4.
5.
TO REPLACE BELT OR BRUSHROLL
6.
With new belt in place, pull and slide brushroll into nozzle making sure tha
t
the brushroll end ca
ps are in the correct orientation (7a inset). Rotate brushroll manually to make sure belt is properly aligned.
Be sure to replace all six (6) screws.
Reattach nozzle guard by carefully sliding back into place. Interlock rollers and nozzle guard by tilting rollers down towards the base while replacing the nozzle guard.
7.
8.
9.
2.
1.
3.
7a.
MOTOR
SHAFT
9
CLOG MAINTENANCE
WARNING: TO REDUCE RISK OF PERSONAL INJURY - UNPLUG CLEANER BEFORE SERVICING
ANY OTHER SERVICING SHOULD BE DONE BY AN AUTHORIZED SERVICE REPRESENTATIVE
CUSTOMER SERVICE (1-800-321-1134)
In the event tha
t further assistance is required,
see your Yellow Pages for an authorized Royal
®
Dealer
.
Costs of any transportation to and
from an
y place of repair are to be paid by the o
wner
.
The ser
vice parts used in this unit are easily replaced and readily available from
an authorized Royal
®
Dealer or retailer. Always identify your cleaner by the model number and manufacturing code when requesting
information or ordering replacement parts. (The model number appears on the bottom of the cleaner.)
PROBLEM POSSIBLE REASON POSSIBLE SOLUTION
Cleaner won’t run
Cleaner won’t pick-up or low suction
Dust escaping from cleaner
1. Power cord not firmly plugged into outlet.
2. Blown fuse or tripped breaker.
3. Needs service.
4. Thermal Protector activated.
1.
Dirt container not installed correctly
.
2. Dirt container full.
3. Brushroll worn.
4. Broken or worn belt.
5. Clogged filter.
6.
Nozzle/brushroll c
logged.
7. Hose clogged.
1. Dirt container full.
2. Dirt container not installed correctly.
3. Hose not installed correctly.
4. Filter not installed completely.
TROUBLESHOOTING GUIDE
1. Plug unit in firmly.
2. Check fuse or breaker in home. Replace fuse/reset breaker.
3. Take to service center or call 1-800-321-1134.
4. Unplug cleaner - allow to cool.
1. Review dirt container removal & replacement ­Pg. 7.
2. Empty dirt container - Pg. 7.
3. Replace brushroll - Pg. 8.
4. Replace belt - Pg. 8.
5. Remove filter and clean - Pg.7.
6. Check nozzle/brushroll; remove obstruction/clog ­Pg. 8.
7.
Remove hose; remove clog - Pg. 9.
1. Empty dirt container - Pg. 7.
2. Review dirt container removal & replacement ­Pg. 7.
3. Review hose installation - Pg. 9.
4. Review filter removal & replacement - Pg. 7.
TOOL REQUIRED: PHILLIPS SCREWDRIVER
WARNING: TO REDUCE THE RISK OF INJURY FROM MOVING PARTS - UNPLUG BEFORE CLEANING CLOG. NOTE: First check brushroll for clog, if clog persists, then check lower hose.
Locate lower hose/clog clean­out (see “FEATURES”, number 15 for location).
Replace lower hose and replace one (1) screw.
2.
1.
Remove one (1) screw and pull lower hose down and away from cleaner.Remove obstruction.
3.
Loading...
+ 10 hidden pages