Remote Control UG-Philips.indd 2Remote Control UG-Philips.indd 27/26/05 11:10:46 AM7/26/05 11:10:46 AM
2
INTRODUCTION
Congratulations! You now have an exclusive DIRECTV®
Universal Remote Control that will control four components, including a DIRECTV Receiver, TV, and two
stereo or video components (for example, a DVD, stereo,
or second TV). Moreover, its sophisticated technology
allows you to consolidate the clutter of your original
remote controls into one easy-to-use unit that’s packed
with features such as:
• Four-position MODE slide switch for easy component
selection
• Code library for popular video and stereo components
• Code search to help program control of older or dis-
continued components
• Memory protection to ensure you will not have to re-
program the remote when the batteries are replaced
Before using your DIRECTV Universal Remote Control,
you may need to program it to operate with your particular component. Please follow the instructions detailed in
this guide to set up your DIRECTV Universal Remote
Control so you can start enjoying its features.
Remote Control UG-Philips.indd 3Remote Control UG-Philips.indd 37/26/05 11:10:46 AM7/26/05 11:10:46 AM
3
FEATURES AND FUNCTIONS
Key Charts
TV
INPUT
FORMAT
PWR
TV
POWER
ON
OFF
AV1 AV2 TV
Slide the MODE switch to
the DIRECTV, AV1, AV2 or
TV positions to select the
component you want to control. A green LED under each
switch position indicates the
component being controlled.
Press TV INPUT to select
the available inputs on your
TV. (Note: Additional setup
is required to activate the
TV INPUT
key. See instruc-
tions on page 10.)
Press FORMAT to cycle
through the resolution and
screen formats. Each press
of the key cycles to the next
available format and /or resolution. (Not available on all
DIRECTV Receivers.)
Press PWR to turn the selected component on or off.
Press TV POWER ON/OFF
to turn the TV and DIRECTV
Receiver on or off. (Note:
These keys are only active after the remote has been setup
for your TV. See page 10.)
Remote Control UG-Philips.indd 4Remote Control UG-Philips.indd 47/26/05 11:10:46 AM7/26/05 11:10:46 AM
continued on next page…
4
FEATURES AND FUNCTIONS
Key Charts (continued)
Use these keys to control
your DVR, VCR, DVD,
or CD/DVD player. To record a program, press the
RECORD key.
REPLAY jumps back 6 sec-
onds and plays video from
that location.
ADVANCE jumps ahead in
a recording.
GUIDE
ACTIVE
LIST
EXIT
SELECT
Use GUIDE to display the
DIRECTV program guide.
Press ACTIVE to access
special features, services,
DIRECTV NEWS™ and
info.
Press LIST to display your
TO DO list of programs. (Not
available on all DIRECTV
Receivers.)
Press EXIT to exit menu
screens and the program
guide and return to live TV.
Press the ARROW keys to
move around in the program
guide and menu screens.
Press SELECT to choose
highlighted items in menu
screens or the program guide.
Remote Control UG-Philips.indd 5Remote Control UG-Philips.indd 57/26/05 11:10:48 AM7/26/05 11:10:48 AM
continued next page…
5
FEATURES AND FUNCTIONS
Key Charts (continued)
BACK
Press BACK to return to the
previously displayed screen.
MENU
INFO
Press MENU to display the
Quick Menu.
Press INFO to display current
channel and program information when watching live
TV or in the Guide.
Press YELLOW in fullscreen TV to cycle through
alternate audio tracks.
Press BLUE in full-screen
TV to display the MiniGuide.
Press RED in the Guide to
jump 1.5 hours back.
Press GREEN in the Guide
to jump 1.5 hours forward.
Other functions vary—look
for onscreen hints or refer to
your DIRECTV Receiver’s
user guide. (Not available on
all DIRECTV Receivers.)
Press VOL to raise or lower
the sound volume. The vol-
VOL
ume key is only active when
the remote is setup for your
TV.
While watching TV, press
CHAN
PAG E
CHANp (or q) to select
the next higher (or lower)
channel.
While in the DIRECTV program guide or menu, press
PAGEp (or q) to page up
(or down) through available
channels in the Guide.
continued next page…
6
Remote Control UG-Philips.indd 6Remote Control UG-Philips.indd 67/26/05 11:10:49 AM7/26/05 11:10:49 AM
FEATURES AND FUNCTIONS
Key Charts (continued)
Press MUTE to turn the
MUTE
PREV
21
ABC
JKL
TUV
5
8
WXYZ
4
GHI
7
PQRD
0
DASHENTER
sound off or back on.
Press PREV to return to the
last channel viewed.
Press the number keys to di-
3
rectly enter a channel number
DEF
(e.g. 207) while watching TV
or in the Guide.
6
MNO
Press DASH to separate main
9
and sub-channel numbers.
Press ENTER to activate
number entries quickly.
Remote Control UG-Philips.indd 7Remote Control UG-Philips.indd 77/26/05 11:10:50 AM7/26/05 11:10:50 AM
7
INSTALLING BATTERIES
–+
–+
1. On the back of the remote control, push down on the
door (as shown), slide the battery cover off, and remove the used batteries.
2. Obtain two (2) new AA alkaline batteries. Match their
+ and - marks to the + and - marks in the battery case,
then insert them.
3. Slide the cover back on until battery door clicks into
place.
8
Remote Control UG-Philips.indd 8Remote Control UG-Philips.indd 87/26/05 11:10:51 AM7/26/05 11:10:51 AM
CONTROLLING YOUR DIRECTV RECEIVER
The DIRECTV Universal Remote Control is designed
to give you access to features and functions found on
your original remote control. To use it with your brand of
DIRECTV Receiver, you will need to setup the remote
control by performing the following steps.
Setting Up Your DIRECTV Remote
1. Locate the DIRECTV Receiver’s brand and model
number (on the back or bottom panel) and write it in
the spaces below.
BRAND: _________________________
MODEL: _________________________
2. Locate the 5-digit code for your DIRECTV Receiver.
(See pages 16-17.)
3. Power on the DIRECTV Receiver.
4. Slide the MODE switch to the DIRECTV position.
5. Press and hold the MUTE and SELECT keys until the
green light under the DIRECTV position fl ashes twice,
then release both keys.
6. Using the number keys, enter the 5-digit code. If per-
formed correctly, the green light under the DIRECTV
position fl ashes twice.
7. Aim the remote at your DIRECTV Receiver and press
the PWR key once. The DIRECTV Receiver should
turn off; if it does not, repeat steps 3 and 4, trying each
code for your brand until you fi nd the correct code.
8. For future reference, write down the working code for
your DIRECTV Receiver in the blocks below:
Onscreen Remote Setup
Once your remote is setup to work with your DIRECTV
Receiver, you can set it up for your other equipment using the steps detailed on the following pages, or you can
set it up it onscreen by pressing MENU, then SELECT
on Settings, Setup in the Quick Menu, then selecting
Remote from the left menu.
Remote Control UG-Philips.indd 9Remote Control UG-Philips.indd 97/26/05 11:10:51 AM7/26/05 11:10:51 AM
9
CONTROLLING YOUR TV
Once you have successfully setup your DIRECTV Remote to operate your DIRECTV Receiver, you can set it
up to control your TV. We recommend you use the on-screen steps described on page 9, but you can also use
the manual method below:
1. Turn on the TV.
NOTE: Please read steps 2-5 completely before proceeding. Highlight or write down the codes and component you wish to setup before moving on to step 2.
2. Locate the 5-digit code for your TV. (See pages 18-
21.)
3. Slide the MODE switch to the TV position.
4. Press and hold the MUTE and SELECT keys at the
same time until the green light under the TV position
fl ashes twice, then release both keys.
5. Using the number keys enter the 5-digit code for your
brand of TV. If performed correctly, the green light
under TV fl ashed twice.
6. Aim the remote at your TV and press the PWR key
once. Your TV should turn off. If it does not turn off,
repeat steps 3 and 4, trying each code for your brand
until you fi nd the correct code.
7. Slide the MODE switch to the DIRECTV position.
Press TV POWER. Your TV should turn on.
8. For future reference, write down the working code for
your TV in the blocks below:
SETTING UP THE TV INPUT KEY
Once you have setup the DIRECTV Remote control for
your TV, you can activate the TV INPUT key so you can
change the “source”— the piece of equipment whose
signal is displayed on your TV:
1. Slide the MODE switch to the TV position.
2. Press and hold the MUTE and SELECT keys until the
3. Using the number keys, enter 9-6-0. (The green light
You can now change the input for your TV.
Remote Control UG-Philips.indd 10Remote Control UG-Philips.indd 107/26/05 11:10:51 AM7/26/05 11:10:51 AM
green light under the TV position fl ashes twice, then
release both keys.
under the TV position fl ashes twice.)
10
Deactive the TV Input Select Key
If you want to deactivate the TV INPUT key, repeat
steps 1 through 3 from the previous section; the green
light will blink 4 times. Pressing the TV INPUT key will
now do nothing.
CONTROLLING OTHER COMPONENTS
The AV1 and AV2 switch positions can be setup to control a VCR, DVD, STEREO, second DIRECTV Receiver
or second TV. We recommend you use the onscreen steps described on page 9, but you can also use the
manual method below:
1. Turn on the component you wish to control (e.g., your
DVD Player).
2. Locate the 5-digit code for your component. (See
pages 16-27.)
3. Slide the MODE switch to the AV1 (or AV2) position.
4. Press and hold the MUTE and SELECT keys at the
same time until the green light under AV1 (or AV2)
fl ashes twice, then release both keys.
5. Using the NUMBER keys, enter the 5-digit code for
the brand of component being setup. If performed
correctly, the green light under the selected position
fl ashes twice.
6. Aim the remote at your component and press the
PWR key once. The component should turn off; if it
does not, repeat steps 3 and 4, trying each code for
your brand until you fi nd the correct code.
7. Repeat steps 1 through 6 to setup a new component
under AV2 (or AV1).
8. For future reference write down the working code for
the component(s) setup under AV1 and AV2 below:
AV1:
COMPONENT: _______________________
AV2:
COMPONENT: _______________________
Remote Control UG-Philips.indd 11Remote Control UG-Philips.indd 117/26/05 11:10:51 AM7/26/05 11:10:51 AM
11
SEARCHING FOR TV, AV1 OR AV2 CODES
If you were unable to fi nd the code for your brand of TV
or component, you can try a code search. This process
may take up to 30 minutes.
1. Turn on the TV or component.
2. Slide the MODE switch to the TV, AV1 or AV2 posi-
tion, as desired.
3. Press and hold the MUTE and SELECT keys at the
same time until the green light under the selected
switch position fl ashes twice, then release both keys.
4. Enter 9-9-1 followed by one of the following 4-digits:
COMPONENT TYPE COMPONENT ID #
Satellite0
TV1
VCR/DVD/PVR2
STEREO3
5. Press PWR, or other functions (e.g. PLAY for VCR)
you want to use.
6. Point the remote at the TV or component and press
CHANp. Repeatedly press CHANp until the TV or
component turns off.
Note: Every time
vances to the next code and power is transmitted to the
component.
7. When the TV or component turns off, stop press-
ing the CHANp key. Then, press and release the
SELECT key.
NOTE: If the light fl ashes 3 times before the TV or
component responds, you’ve cycled through all codes
and the code you need is not available. You must use
the remote that came with your TV or component.
CHAN
p is pressed the remote ad-
Verifying the Codes
Once you have setup the DIRECTV Universal Remote
Control using the above steps, use the following instructions to fi nd out the 5-digit code to which your compo-
nent responded:
1. Slide the MODE switch to the appropriate position.
2. Press and hold the MUTE and SELECT keys at the
3. Enter 9-9-0. (The green light under the selected
Remote Control UG-Philips.indd 12Remote Control UG-Philips.indd 127/26/05 11:10:51 AM7/26/05 11:10:51 AM
same time until the green light under the selected
switch position fl ashes twice, then release both keys.
switch position fl ashes twice.)
12
4. To view the fi rst digit in the code, Press and release
the number 1 key. Wait three seconds, and count the
number of times the green light fl ashes. Write this
number down in the leftmost TV, AV1 or AV2 code
box found on pages 11.
Note: If this part of the code is “0” the light will not
fl ash.
5. Repeat step 4 four more times for the remaining digits;
i.e., press number 2 for the second digit, 3 for the third
digit, 4 for the fourth digit and 5 for the fi nal digit.
CHANGING VOLUME LOCK
Depending on how you set up your remote, the VOL and
MUTE may control the volume only on your TV, regard-
less of the position of the MODE switch. This remote
can be setup so that the VOL and MUTE keys work only
with the component selected by the MODE switch. To
enable this feature, perform the following steps:
1. Press and hold the MUTE and SELECT keys until the
green light under the DIRECTV position fl ashes twice,
then release both keys.
2. Using the number keys, enter 9-9-3. (The green light
fl ashes twice after the 3.)
3. Press and release the VOLp key. (The green light
fl ashes 4 times.)
Now the VOL and MUTE keys will work only for the
component selected by the MODE switch position.
To Lock Volume to AV1, AV2 or TV
1. Slide the MODE switch to the AV1, AV2 or TV posi-
tion to lock the volume.
2. Press and hold the MUTE and SELECT keys until the
green light under the selected switch fl ashes twice and
release both keys.
3. Using the number keys, enter 9-9-3. (The green light
fl ashes twice.)
4. Press and release the SELECT key. (The green light
fl ashes twice.)
13
Remote Control UG-Philips.indd 13Remote Control UG-Philips.indd 137/26/05 11:10:52 AM7/26/05 11:10:52 AM
RESTORE FACTORY DEFAULT SETTINGS
To reset all the functions of the remote control to the
factory defaults (the original, out-of-the-box settings),
follow these steps:
1. Press and hold the MUTE and SELECT keys at the
same time until the green light fl ashes twice, then re-
lease both keys.
2. Using the number keys, enter 9-8-1. (The green light
fl ashes 4 times.)
Remote Control UG-Philips.indd 14Remote Control UG-Philips.indd 147/26/05 11:10:52 AM7/26/05 11:10:52 AM
14
TROUBLESHOOTING
PROBLEM: Light at the top of the remote blinks when you
press a key, but the component does not respond.
SOLUTION 1: Try replacing the batteries (see page 8).
®
SOLUTION 2: Make sure you are aiming the DIRECTV
Universal Remote Control at your home entertainment component and that you are within 15 feet
of the component you are trying to control.
PROBLEM: The DIRECTV Universal Remote Control does
not control component or commands are not
recognized properly.
SOLUTION: Try all listed codes for the device brand being
set up. Make sure all components can be operated with an infrared remote control.
PROBLEM: TV/VCR combo does not respond properly.
SOLUTION: Use the VCR codes for your brand. Some com-
bo units may require both a TV code and a VCR
code for full operation (see page 12).
PROBLEM: CHANp, CHAN q, and PREV do not work
for your RCA TV.
SOLUTION: Due to RCA design for certain models (1983-
1987), only the original remote control will
operate these functions.
PROBLEM: Changing channels does not work properly.
SOLUTION: If original remote control required pressing
ENTER to change channels, press ENTER on
the DIRECTV Universal remote control after
entering a channel number.
PROBLEM: Remote control does not turn on Sony or Sharp
TV/VCR Combo.
SOLUTION: For power on, these products require setting up
TV codes on the remote control. For Sony, use
TV code 0000 and VCR code 0032. For Sharp,
use TV code 0093 and VCR code 0048.
15
Remote Control UG-Philips.indd 15Remote Control UG-Philips.indd 157/26/05 11:10:52 AM7/26/05 11:10:52 AM
DIRECTV SETUP CODES
Setup Codes for DIRECTV Receivers
DIRECTV Model D-1000001, 00002
Hughes Network Systems (most models) 00749
Hughes Network Systems models GAEB0, GAEB0A,
GCEB0, GCEB0A, HBH-SA, and HAH-SA01749
GE models GRD33G2A and GRD33G3A,
GRD122GW 00566
Hitachi model HDS210R 00819
Mitsubishi HD models SRHD400 and SRHD500 00749
Panasonic models TZ-DBS01 and TZ-DRD100 00247
Panasonic models TUIRD10 and TUIRD20 00701
Philips models DSX5150R,DSX525R/I, DSX5350R,
DSX5353R, DSX5353X, and DSX5375R 01076
Remote Control UG-Philips.indd 26Remote Control UG-Philips.indd 267/26/05 11:10:54 AM7/26/05 11:10:54 AM
26
Sharper Image31556
Sherwood31653, 30502, 30491
Soundesign30670
Stereophonics31023
Sunfi re31313
Teac30463, 31528, 31390, 31074
Technics31308, 31518, 30039, 30309
Thorens31189
Venturer31390
Victor30074
Wards30158, 30189, 30080, 30014
Yamaha30176, 30186, 31375, 31331, 31176
Yorx30195
Zenith31293, 30857, 31869
Setup Codes for Stereo Amplifi ers
Aiwa30406
Bose30674
Carver30269
Curtis Mathes30300
Denon30160
Durabrand31561
GE30078
Harman/Kardon30892
JVC30331
Left Coast30892
Lenoxx31561
Linn30269
Luxman30165
Magnavox30269
Marantz30892, 30321, 30269
Nakamichi30321
NEC30264
Optimus30395, 30300
Panasonic30308, 30521
Parasound30246
Philips30892, 30269
Pioneer30300, 30013
Polk Audio30892, 30269
RCA30300
Realistic30395
Sansui30321
Shure30264
Sony30689, 30815, 30220
Soundesign30078, 30211
Technics30521, 30308
Victor30331
Wards30078, 30013, 30211
Yamaha30354, 30143, 30133
Remote Control UG-Philips.indd 27Remote Control UG-Philips.indd 277/26/05 11:10:54 AM7/26/05 11:10:54 AM
27
REPAIR OR REPLACEMENT POLICY
If the DIRECTV Universal Remote Control does not function
properly, DIRECTV will, at our sole discretion, repair or replace
the DIRECTV Universal Remote Control, provided that:
a. You are a customer of DIRECTV and your account is in good
standing; and
b. The problem with the DIRECTV Universal Remote Control
was not caused by abuse, mishandling, alteration, accident,
failure to follow operating, maintenance or environmental
instructions set forth in this User Guide, or service performed
by someone other than DIRECTV.
THE DIRECTV UNIVERSAL REMOTE CONTROL IS PROVIDED ON AN AS IS, AS AVAILABLE BASIS, SOLELY
FOR YOUR NON-COMMERCIAL, RESIDENTIAL USE.
DIRECTV DOES NOT MAKE ANY REPRESENTATIONS OR WARRANTIES OF ANY KIND, WHETHER
STATUTORY, EXPRESS OR IMPLIED, REGARDING THE
DIRECTV UNIVERSAL REMOTE CONTROL, INCLUDING
ANY IMPLIED WARRANTY OF MERCHANTABILITY,
NONINFRINGEMENT OR FITNESS FOR A PARTICULAR
PURPOSE OR IMPLIED WARRANTIES ARISING FROM A
COURSE OF DEALING OR COURSE OF PERFORMANCE.
DIRECTV EXPRESSLY DISCLAIMS ANY REPRESENTATION OR WARRANTY THAT THE DIRECTV UNIVERSAL REMOTE CONTROL WILL BE ERROR FREE. NO
ORAL ADVICE OR WRITTEN INFORMATION GIVEN
BY DIRECTV, ITS EMPLOYEES, AND LICENSORS OR
THE LIKE SHALL CREATE A WARRANTY; NOR SHALL
CUSTOMER RELY ON ANY SUCH INFORMATION OR
ADVICE.
UNDER NO CIRCUMSTANCES, INCLUDING NEGLIGENCE, SHALL DIRECTV OR ANYONE ELSE INVOLVED
IN ADMINISTERING, DISTRIBUTING, OR PROVIDING
THE DIRECTV UNIVERSAL REMOTE CONTROL BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOSS OF REVENUES OR INABILITY TO
USE THE DIRECTV UNIVERSAL REMOTE CONTROL,
MISTAKES, OMISSIONS, INTERRUPTIONS, DEFECTS,
FAILURE OF PERFORMANCE, EVEN IF DIRECTV HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES.
Because some states do not allow the exclusion or limitation of
liability for consequential or incidental damages, in such states,
DIRECTV’s liability is limited to the greatest extent permitted
by law.
Remote Control UG-Philips.indd 28Remote Control UG-Philips.indd 287/26/05 11:10:55 AM7/26/05 11:10:55 AM
28
ADDITIONAL INFORMATION
This product does not have any user-serviceable parts.
Opening the case, except for the battery cover, may
cause permanent damage to your DIRECTV Universal
Remote Control.
For help via the Internet, visit us at: DIRECTV.com
Or ask for technical support at: 1-800-531-5000
Copyright 2005 by DIRECTV, Inc. No part of this publication may be reproduced, transmitted, transcribed,
stored in any retrieval system, or translated to any language, in any form or by any means, electronic, mechanical, magnetic, optical, manual, or otherwise, without
prior written permission of DIRECTV, Inc.
DIRECTV, the Cyclone Design logo and DIRECTV
NEWS are trademarks of DIRECTV, Inc.
M2081B for use with the URC2081/2082, DIRECTV
Universal Remote Control.
06/05
Remote Control UG-Philips.indd 29Remote Control UG-Philips.indd 297/26/05 11:10:55 AM7/26/05 11:10:55 AM
29
COMPLIANCE WITH FCC RULES AND
REGULATIONS
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if
not used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:
• Increase or decrease the separation between the equipment and receiver.
• Consult the dealer or an experienced remote control/
TV technician for help.
This equipment has been verifi ed to comply with the
limits for a Class B computing device, pursuant to FCC
Rules. The user is cautioned that changes and modifi ca-
tions made to the equipment without the approval of
manufacturer could void the user’s authority to operate
this equipment.
FCC Authorization Label
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired operation.
Responsible Party:
DIRECTV, Inc.
2230 E. Imperial Hwy.
El Segundo, CA 90245
1-800-531-5000
30
Remote Control UG-Philips.indd 30Remote Control UG-Philips.indd 307/26/05 11:10:55 AM7/26/05 11:10:55 AM
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.