DirecTV HBH-SA, SD-HBH User Manual

DIRECTV Receiver

Owners Manual

POWER

SELECT

Models HAH-SA

HBH-SA

SD-HBH

HUGHES WARRANTY REGISTRATION You may REGISTER ONLINE at: www.hns-usa.com/warranty

or complete the registration form on the back of this manual.

1034354-0001 Rev. A

rights reserved. This publication and its contents are proprietary to Hughes Network Systems, Inc., a wholly owned subsidiary of Hughes Electronics Corporation

. No part of this publication may be

reproduced in any form or by any means without the written permission of Hughes Network Systems, Inc., 11717 Exploration Lane, Germantown, Maryland 20876.

Hughes Network Systems, Inc. has made every effort to ensure the correctness and completeness of the material in this document. Hughes Network Systems, Inc. shall not be liable for errors contained herein. The information in this document is subject to change without notice. Hughes Network Systems, Inc. makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular pur pose. Covered by one or more of the following U.S. Patents: 6,075,526;5,828,419; 5,751,372; 5,694,176; and 5,635,989. This product is subject to one or more U.S. or foreign patents pending.

Software contained in the HAH-SA, HBH-SA and SD-HBH receivers and referenced in this manual is copyright

1995-2003 by Hughes Network Systems, Inc., a wholly owned subsidiary of Hughes Electronics Corporation. Some features are patent pending. WatchWizard, PreSelect, TurboTune, and OneLine Guide are trademarks of Hughes Network Systems. “NFL,” the NFL Shield, and “NFL SUNDAY TICKET” are registered trademarks of the National Football League and its affiliates. “NHL,’” the NHL Shield, and “NHL CENTER ICE” are registered trademarks of the National Hockey League. “MLB,” “MLB EXTRA INNINGS,” “Major League Baseball,” and the Major League Baseball silhouetted batter logo are service marks of Major League Baseball Properties, Inc. Major League Baseball trademarks and copyright are used with permission of Major League Baseball Properties, Inc. All other trademarks and service marks are the property of their respective owners.

Disclaimer – Every effort has been made to ensure the correctness and completeness of the material in this document. No company shall be liable for errors contained herein. The information in this document is subject to change without notice, No warranty of any kind is made with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular pur pose.

Trademarks – DIRECTV and the Cyclone Design logo, DIRECTV INTERACTIVE, TOTAL CHOICE and DIRECTV HOME SERVICES are trademarks of DIRECTV, Inc., a unit of Hughes Electronics Corp. FREEVIEW is a registered trademark of Hughes Electronics Corporation. All trademarks, marks, names, or product names referenced in this publication are the property of their respective owners, and Hughes Network Systems neither endorses nor otherwise sponsors any such products or services referred to herein.

Dolby Laboratories Information – Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic,” and the double-D symbol are trademarks of Dolby Laboratories.

Macrovision

Information – Macrovision is a registered trademark

of Macrovision Corporation. This device incorporates an anticopy process technology that is protected by U.S. patents 4,631,603; 4,577,216; 4,819,098; and other intellectual property rights. The anticopy process is licensed for noncommercial, home use only. Reverse engineering or disassembly is prohibited.

StarSight

Information – StarSight® features licensed under one or

more of the following patents: 4,706,121; 5,151,789; 5,353,121; 5,353,277; 5,479,266; 5,479,268; and 5,532,754. Use rights reserved.

™

TruSurround™ Information – TruSurround

and the symbol are trademarks of SRS Labs, Inc. TruSurround technology is incorporated under license from SRS Labs, Inc.

Information – WINK® and the symbol are registered

WINK

trademarks of WINK Communications, Inc.

NERGYSTA R

Information – ENERGYSTAR

and the ENERGYSTAR

certification mark are registered US marks.

Note on recording programming – Most television programs and films are copyrighted. This means that someone has legal rights governing the reproduction and distribution of this material. In certain circumstances, copyright law may apply to private in-home taping of copyrighted materials. In most cases, it is permissible to record for your personal use, as long as you do not sell the material. You must act responsibly in this area–check into the matter if you are unsure.

Some pay per view programs may be licensed from producers as “view-only” programs. These are copyrighted programs, and may not be copied or reproduced for any purpose without the express written permission of the copyright owner.

DIRECTV

Programming – ACTIVATION OF PROGRAMMING

MAY BE SUBJECT TO CREDIT CARD APPROVAL AND REQUIRES VALID SERVICE ADDRESS, SOCIAL SECURITY NUMBER, AND/OR MAJOR CREDIT CARD. Deposit or prepayment may be required. Programming subject to change. You must be physically located in the United States (U.S.) to receive DIRECTV service. DIRECTV services are not available outside the United States. DIRECTV programming is sold separately and independently of DIRECTV System hardware. A valid programming subscription is required to operate DIRECTV System hardware. Activate your DIRECTV programming today at 1-800-DIRECTV (1-800-347-3288).

DIRECTV System hardware and installation – To arrange for professional installation of your DIRECTV System, ask questions, or resolve problems related to your DIRECTV System, contact your dealer. If you need more information, please contact our technical support line at 1-800-274-8995.

Spanish language owner’s manual – A Spanish language version of this manual is available upon request. To obtain a copy, contact the Customer Care Center at 1-800-274-8995. You may also download a copy of the manual from www.hns.com on the internet.

Manual del propietario en idioma español – Contamos con una versión de este manual en idioma español, que está a su disposición. Para obtener una copia, llame al Centro de Atención al Cliente al 1-800-274-8995. También puede descargar una copia del manual en Internet en www.hns.com.

Please record the following information for warranty

System Model #: ___ ___ ___ ___ ___

(if applicable)

Receiver Model #: ___________________________

Receiver Serial #: ___________________________

Access Card #: _________ __________ _________

Receiver Serial #: ___________________________

Receiver ID #: ______________________________

Important Safety Instructions

For your safety and protection, read this entire Owner's Manual before you attempt to install or use your satellite system. In particular, read this safety section carefully. Keep this safety information where you can refer to it if necessary.

Heed Cautions–All cautions on the product and in the operating instructions should be adhered to. Follow Instructions–All operating and use instructions should be followed.

THESE CAUTIONS AND SYMBOLS APPEAR ON THE BACK OF THE RECEIVER

WARNING or CAUTION

Double insulated systems are protected by additional board clearances and creepage, so that the unit will not be a safety hazard to the end-user.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

CAUTION

RISK OF ELECTRICAL SHOCK

DO NOT OPEN

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Unplug this apparatus during lightning storms or when unused for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

iii

INSTALLATION

Ground

clamp

Electric

service

equipment

Ground clamps

Power service grounding electrode

Grounding conductor

Coaxial cable

Grounding block

Coaxial cable

Polarization – This DIRECTV® Receiver is equipped with a plug that will fit into the power outlet only one way. Do not modify the plug defeating this feature. If the plug does not fit, contact your electrician to replace your outlet. To prevent electric shock, do not use this plug with an extension cord or outlet unless you can fully insert the blades without blade exposure

Power Sources – Operate this DIRECTV Receiver only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.

Power-Cord Protection – Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electrical shock.

Ventilation – Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

The openings should never be blocked by placing the product on a bed, sofa, rug, or similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s instructions have been adhered to.

For electrical safety, power line operated equipment or accessories connected to this unit should bear the UL listing mark and should not be modified so as to defeat the safety features. This will help avoid any potential hazard from electrical shock or fire. If in doubt, contact qualified service personnel.

Heat–Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

Accessories – To avoid personal injury or damage to the DIRECTV Receiver, do not place the DIRECTV Receiver on any unstable cart, stand, table, or bracket. Any mounting of the product should follow the manufacturer’s instructions.

Attachments – Do not use attachments unless recommended by DIRECTV as they may cause hazards.

Satellite Dish Antenna Grounding – The outdoor satellite dish antenna

used to receive satellite signals and the cable used to connect the satellite dish antenna to the indoor receiving unit are required to comply with local installation codes and the appropriate sections of the National Electric Code (NEC) and in particular Article 810-15, which covers proper installation and grounding of television receiving equipment, as well as to Article 820-33, which specifies that the satellite dish antenna cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. These codes require proper grounding of the metal structure of the outdoor satellite dish antenna and grounding of the connecting cable at a point where it enters the house (or other building). If you are having a professional installer perform the installation, the installer must observe installation codes. This manual contains instructions on how to make the installation in compliance with the NEC. If additional local installation codes apply, contact local inspection authorities.

Example of Antenna Grounding according to the National Electrical Code instructions contained in “Radio and Television Equipment”.

Note: The DIRECTV Receiver must be grounded through the satellite/ local antenna cable before plugging into the telephone jack, and it must remain grounded thereafter.

Water and Moisture – WARNING! To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.

Lightning – For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet, disconnect the antenna and cable system, and disconnect it from the telephone line. This will prevent damage to the product due to lightning and power-line surges.

Television Antenna Information – Installing an outdoor antenna can be hazardous and should be left to a professional antenna installer. Do not locate the outside antenna system in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, take extreme care to keep from touching such power lines or circuits, as contact with them might be fatal. If an outside antenna is connected to the DIRECTV Receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. This DIRECTV Receiver is equipped with a plug that will fit into the power outlet only one way. Do not modify the plug defeating this feature. If the plug does not fit, contact your electrician to replace your outlet. To prevent electric shock, do not use this plug with an extension cord or outlet unless you can fully insert the blades without blade exposure. Section 810 of the NEC, NFPA No. 70 1987, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of the grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Power Lines – Extreme care must be taken when installing and adjusting

or maintaining the outdoor antenna and connecting cable, especially in the vicinity of overhead power lines, electric lights, or power circuits. When installing the outdoor antenna or cable, extreme care should be taken to keep from touching or approaching such power lines or circuits, as contact with them might be fatal.

Cleaning – Unplug this receiver from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use only a damp cloth for cleaning.

Object and Liquid Entry – Never push objects of any kind into this DIRECTV Receiver through openings as they may touch dangerous voltages or “short out” parts that could result in a fire or electric shock. Never spill liquid of any kind on the receiver. No objects filled with liquids, such as vases, shall be placed on the apparatus.

SERVICE

Servicing–Do not attempt to service this DIRECTV® Receiver yourself as

opening or removing covers may expose you to dangerous voltage or other hazards. There are no user serviceable parts inside. Refer all servicing to qualified service personnel.

Conditions Requiring Service–Unplug the DIRECTV Receiver from the wall outlet and refer servicing to qualified personnel under the following conditions:

• When the power supply cord or plug has been damaged.

• If liquid has been spilled on, or objects have fallen into, the DIRECTV Receiver or it has been exposed to water.

• If the DIRECTV Receiver does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions. Other adjustments may result in damage and will often require extensive work by a qualified technician to restore the DIRECTV Receiver to its normal operation.

• If the DIRECTV Receiver has been dropped or the cabinet has been damaged.

• When the DIRECTV Receiver exhibits a distinct change in performance.

Replacement Parts–When replacement parts are required, have the technician verify that the replacements being used have the same safety characteristics as the original parts. Use of replacement parts specified by the manufacturer can prevent fire, electric shock, or other hazards.

Safety Check–Upon completion of any service or repairs to this DIRECTV Receiver, ask the service technician to perform safety checks recommended by the manufacturer to determine that the DIRECTV Receiver is in safe operating condition.

Multi-satellite capability–Multi-satellite capable if used with a DIRECTV Multi-Satellite Dish Antenna, not included.

Automatic upgrades–Your DIRECTV Receiver is able to receive upgrades or modifications to some of its features and functions. These modifications will occur automatically, usually at times when the receiver would likely be turned off. If your receiver is on when an upgrade or modification is sent, you may experience a disruption in reception for a minute or two. Your reception should return to normal after the modification is complete. Your receiver must be plugged in to receive any upgrades. Do not unplug you receiver while an upgrade is in progress. Please consult the Upgrade menu to find a schedule of upgrades or modifications planned by DIRECTV.

Local channel availability–With this receiver (HAH-SA, HBH-SA, SD-HBH) and the proper satellite dish antenna, you may be able to subscribe to local channels from DIRECTV in certain areas. Additional equipment may be required in some markets. Check with your retailer or visit DIRECTV.com for information on availability of local channels from DIRECTV in your area.

Federal Communications Commission (FCC) Regulatory Information

Declaration of Conformity– Standards to which Conformity is declared: FCC Part 15

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

• Responsible Party’s Name: Hughes Network Systems, Inc.

Address: 11717 Exploration Lane, Germantown, MD 20876 Telephone: 1-800-274-8995

• Trade Name: Hughes

• Type of Equipment: Satellite Receiver

• Model Numbers: HAH-SA, HBH-SA, SD-HBH, HRMC-11, HRMC-12, HRMC-13

Federal Communications Commission (FCC)–This equipment complies with both Part 15 and Part 68 of the FCC rules

Part 15 Compliance–This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by removing and applying power to the equipment, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving satellite dish antenna.

• Increase the separation between the equipment and the DIRECTV

• Connect the equipment into an outlet on a circuit different from that to which the DIRECTV Receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify and Resolve Radio and TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, DC.

To meet FCC requirement, only peripherals (computer input/output devices, terminals, printers, etc.) certified to comply with Class B limits may be attached to this device. Operation with noncertified peripherals is likely to result in interference to radio and TV reception.

To meet FCC requirements, shielded cables are required to connect the device to a personal computer, peripheral, or other Class B certified device.

Part 68 Compliance –This equipment complies with Part 68 of the FCC rules and requirements adopted by the ACTA. On the rear panel of this equipment is a label that contains, among other information, a product identifier in the format US:5L4DT00B3003670. If requested, this information must be provided to the Telephone Company.

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.

The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the local Telephone Company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:5L4DT00B3003670. The digits represented by the ## are the REN without the decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.

If the DIRECTV Receiver (Model Numbers: HAH-SA, HBH-SA, SD-HBH) causes harm to the telephone network, the Telephone Company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the Telephone Company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The Telephone Company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the Telephone Company will provide advance notice in order for you to make the necessary modifications to maintain uninterrupted service.

If trouble is experienced with the DIRECTV Receiver (Model Numbers: HAH-SA, HBH-SA, SD-HBH) equipment, for repair or warranty information, please contact

Hughes Customer Care Center Germantown, MD 20876 Telephone Number: 1-800-274-8995 http://www.hns.com

email: hughestv@hns.com If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect the equipment until the problem is resolved.

Hughes Network Systems must make any necessary repairs to the modem portion of this equipment in order to maintain valid FCC registration. Do not attempt to repair or service your modem. Return it to Hughes Network Systems.

No repairs can be made by customers. All repairs must be done by Hughes Network Systems Authorized Service Centers (ASCs). This equipment cannot be used on public coin service provided by the Telephone Company. Connection to Party Line Service is subject to state tariffs. Contact the state public utility commission, public service commission or corporate commission for information.

Receiver.

Contents

Getting Started . . . . . . . . . . . . . . . . . . . . . . . 1

Setup overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Attach the satellite antenna cable . . . . . . . . . . . . 2

Connect your TV. . . . . . . . . . . . . . . . . . . . . . . . .3

Determine antenna angles . . . . . . . . . . . . . . . . . .4

Testing your system . . . . . . . . . . . . . . . . . . . . . .5

To perform the Transponder test: . . . . . . . . . . 5

Adding system components . . . . . . . . . . . . . 7

Connecting additional system components. . . . . . . 7

Connecting a terrestrial antenna/CATV . . . . . . . 7

Connecting a VCR . . . . . . . . . . . . . . . . . . . . . . .7

Connect the VCR Control Cable. . . . . . . . . . .8

Test the VCR (Record/Stop) . . . . . . . . . . . . . .8

Connecting a home entertainment system. . . . . . 9

Using the remote control . . . . . . . . . . . . . . 11

Remote control functions . . . . . . . . . . . . . . . . . . . 13

Programming the remote control. . . . . . . . . . . . . .14

Code Entry. . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Code Scanning. . . . . . . . . . . . . . . . . . . . . . . . . .15

Changing the Remote ID. . . . . . . . . . . . . . . . . . 15

Installing remote control batteries. . . . . . . . . . . 15

Using program guides. . . . . . . . . . . . . . . . . 17

Selecting a program guide style . . . . . . . . . . . . . .17

Grid guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Logo guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Program guide and menu features. . . . . . . . . . . . . 19

Using the OneLine Using TurboTune

Setting TurboTune channels . . . . . . . . . . . . . . . 20

Renaming TurboTune groups . . . . . . . . . . . . . .21

Using DIRECTV INTERACTIVE™

Setting guide preferences . . . . . . . . . . . . . . . . . . .22

™

Guide . . . . . . . . . . . . . . . . . . 20

™

. . . . . . . . . . . . . . . . . . . . . . . .20

. . . . . . . . .21

Using the menus . . . . . . . . . . . . . . . . . . . . . 23

Onscreen menu icons . . . . . . . . . . . . . . . . . . . . . 24

Purchasing pay per view (PPV) events . . . . . . . . .24

Cancelling purchases. . . . . . . . . . . . . . . . . . . . .24

Reviewing past purchases . . . . . . . . . . . . . . . . .24

Listing unviewed purchases . . . . . . . . . . . . . . . 25

Adjusting audio settings . . . . . . . . . . . . . . . . . . . . 25

Setting default and alternate audio . . . . . . . . . . 25

Using TruSurround . . . . . . . . . . . . . . . . . . . . . 26

Using Dolby Digital audio . . . . . . . . . . . . . . . . 26

Adjusting video settings . . . . . . . . . . . . . . . . . . . . 26

Using WatchWizard™ . . . . . . . . . . . . . . . . . . . . . 27

Using the Channels search . . . . . . . . . . . . . . 28

Using the Program Director . . . . . . . . . . . . . . . . . 28

Scheduling or editing an event . . . . . . . . . . . . . 29

Adjusting system settings . . . . . . . . . . . . . . . . . . . 30

Set output channel. . . . . . . . . . . . . . . . . . . . . . . 30

Input key enable/disable . . . . . . . . . . . . . . . . . . 30

Select menu language . . . . . . . . . . . . . . . . . . . . 30

Caller ID enable/disable . . . . . . . . . . . . . . . . . . 30

Restore factory default settings. . . . . . . . . . . . . 30

Viewing Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Using Caller ID. . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Setting favorites and filters . . . . . . . . . . . . .33

Using favorite channel lists. . . . . . . . . . . . . . . . . . 33

Creating a channel list. . . . . . . . . . . . . . . . . . . . 33

Renaming a channel list:. . . . . . . . . . . . . . . . . . 34

Creating an Auto Set list. . . . . . . . . . . . . . . . . . 34

Adding and removing channels . . . . . . . . . . . . 34

Finding new channels . . . . . . . . . . . . . . . . . . . . 35

Filtering the program guide . . . . . . . . . . . . . . . . . 35

Using Theme Filters . . . . . . . . . . . . . . . . . . . . . 35

Selecting guide times . . . . . . . . . . . . . . . . . . . . 36

Using access controls . . . . . . . . . . . . . . . . . .37

Locking & unlocking the system . . . . . . . . . . . . . 37

How to lock the system. . . . . . . . . . . . . . . . . . . 37

Unlocking the system . . . . . . . . . . . . . . . . . . . . 37

Setting ratings limits . . . . . . . . . . . . . . . . . . . . . 37

Setting spending and time limits. . . . . . . . . . . . 38

Questions & Answers . . . . . . . . . . . . . . . . . .39

Manufacturers device control codes . . . . . .41

Contents

vii

viii

Contents

This chapter explains how to:

Getting Started 1

You may connect a second DIRECTV Receiver to the unused LNB output. These instructions also apply to an additional receiver.

• Connect the DIRECTV® Satellite Dish Antenna to your DIRECTV Receiver (this page).

• Connect your DIRECTV Receiver to your TV (see page 3).

• Find antenna azimuth and elevation settings for your location (see page 4).

• Test the DIRECTV System operation (see page 5).

How to use this manual

This manual uses these typographical conventions to help clarify instructions:

Text Example Description

Click Cancel.

Highlight the Messages button.

Press the INFO button. Connect a pair of A/V cables to the

AUDIO IN jack.

Highlight the Options tab.

Display the MAIN MENU.

On-screen command buttons that execute an action.

Selections or other option buttons within a menu pane.

Remote control buttons, or receiver front panel. Names of equipment cable connections on equipment.

Menu tab names.

Menu and pane names, names of pop-up and sub-menu panes.

Setup overview At this point, you should have:

• Mounted the DIRECTV Satellite Antenna and pointed it in the general direction of the satellite.

• Grounded the antenna as described in your antenna installation instructions.

• Attached RG-6 coaxial cable(s) to the antenna LNB connector(s).

• Routed the other end of the antenna cable to the back of your DIRECTV

Receiver.

• Placed the DIRECTV Receiver accessible to a telephone modular jack.

• Inserted the access card into your DIRECTV Receiver.

Ensure that you have completed these procedures, then continue to the next page to begin installing the DIRECTV Receiver.

Getting Started

Attach the satellite

antenna cable

You can configure your system several ways, depending on what additional components (such as a VCR, DVD player, or A/V receiver) you select. For now, however, use the simplest configuration to check your antenna and cabling.

• Ensure that the DIRECTV

• Attach the RG-6 coaxial antenna cable to the

Receiver is not plugged into an electrical outlet.

SATELLITE IN connector on

the back of the DIRECTV Receiver. Refer to the appropriate figure below.

HAH-SA

SATELLITE IN

DATA PORT

1 SATELLITE IN connector 8 Pb component output jack

2 OUT TO TV connector 9 Y component output jack

3 TV ANTENNA/CABLE IN connector 10 VCR CONTROL cable jack

4 AUDIO OUTPUT (R) jacks 11 S-VIDEO jack

5 AUDIO OUTPUT (L) jacks 12 DIGITAL AUDIO OUTPUT optical jack

6 VIDEO OUTPUT jacks 13 TELEPHONE JACK

7 Pr component output jack 14 AC POWER CORD

HBH-SA / SD-HBH

Model No. HAH-SA

Tested to Comply With FCC Standards

FOR HOME OR OFFICE USE

AUDIO/VIDEO APPARATUS

52BN

E212442

TV ANT/CABLE IN (NOT SATELLITE)

OUT TO TV

PR PB

AUDIO

87 9

TruSurround, SRS and symbol are trademarks of SRS Labs, Inc.

S-VIDEO

VIDEO

DIGITAL

AUDIO OUT

CAUTION

RISK OF ELECTRICAL SHOCK

DO NOT OPEN

120V-1A, 60Hz

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Complies with 47 CFR Part 68. US: 5L4DT00B3003670

This product and service are covered by one or more U.S. patents. Other U.S. and foreign patents pending. See Users Manual for details.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

PHONE JACK

Manufactured by Hughes Network Systems

Table 1: Rear panel connections - DIRECTV Receiver model HAH-SA

TruSurround, SRS and symbol

SATELLITE IN

TV ANT/CABLE IN (NOT SATELLITE)

OUT TO TV

AUDIO

are trademarks of SRS Labs, Inc.

VIDEO S-VIDEO

CAUTION

RISK OF ELECTRICAL SHOCK

DO NOT OPEN

120V-1A, 60Hz

Complies with 47 CFR Part 68. US: 5L4DT00B3003670

This product and service are covered by one or more U.S. patents. Other U.S. and foreign patents pending. See Users Manual for details.

PHONE JACK

Manufactured by Hughes Network Systems

Model No.

Tested to Comply With FCC Standards

FOR HOME OR OFFICE USE

Table 2: Rear panel connections - DIRECTV Receiver model HBH-SA/SD-HBH

1 SATELLITE IN connector 6 VIDEO OUTPUT jacks

2 OUT TO TV connector 7 S-VIDEO jack

3 TV ANTENNA/CABLE IN connector 8 TELEPHONE jack

4 AUDIO OUTPUT (R) jack 9 AC POWER CORD

5 AUDIO OUTPUT (L) jack

AUDIO/VIDEO APPARATUS

52BN

E212442

Getting Started

Connect your TV

Depending on your TV, you can connect it to the receiver in one of four ways:

• Component (Y,Pb,Pr,-HAH-SA only) video cable (best picture quality) or

• S-Video cable (excellent picture quality) or

• Video cable (very good picture quality) or

• Coaxial cable (good picture quality)

You will also want to use a pair of audio cables (L/R) to provide stereo sound. If your TV does not have standard A/V jacks, you will hear monophonic audio. This is acceptable for the procedures described in the next section.

To connect your TV to the DIRECTV

Receiver:

1. Select the appropriate connection:

If your TV has component video jacks –

• Use a component video cable (not supplied) or supplied A/V cable to connect the DIRECTV Receiver’s

Y, PB, and PR output to the

corresponding TV input jacks.

• Use supplied A/V cable to connect the DIRECTV Receiver’s (

L/R) jacks to the TV’s AUDIO IN jacks.

AUDIO

If your TV has an S-Video jack –

• Use an S-Video cable (not supplied) to connect the DIRECTV Receiver’s

• Use supplied A/V cable to connect the DIRECTV Receiver’s

S-VIDEO jack to the TV’s S-VIDEO input jack.

AUDIO

(L/R) jacks to the TV’s AUDIO IN jacks.

The data port (HAH-SA only) is used for diagnostic and aftermarket service. Professional installations using the data port must utilize a good quality shielded cable to ensure FCC compliance.

If your TV has RCA-type A/V connectors –

• Use the supplied A/V cable to connect the DIRECTV Receiver’s

AUDIO and VIDEO jacks to the TV’s A/V IN jacks.

• If your TV has only one

jack to the TV AUDIO IN jack.

AUDIO IN jack, connect the receiver’s AUDIO

If your TV only has an RF (coaxial) connector –

• Connect the DIRECTV Receiver’s

VHF/UHF IN or RF IN jack.

OUT TO TV connector to the TV’s

2. Connect one end of the telephone line cord provided into the DIRECTV Receiver’s

PHONE JACK.

3. Connect the other end into a modular telephone outlet.

4. Plug the TV into an electrical outlet.

5. Plug the DIRECTV Receiver power cord into an electrical outlet. If the front panel Power indicator does not illuminate, press the

POWER button.

Getting Started

Determine antenna

SELECT

POWER

angles

This section explains how to determine the proper antenna position, expressed in degrees of azimuth (horizontal) and elevation (vertical). Use the receiver front panel controls shown below to complete this procedure.

Power

On/Standby

1. Press the front panel

Power

Main Menu

Indicator

POWER

MENU button to display the MAIN MENU below.

2. Use the button to highlight the

MAIN MENU Tue, Nov 6 4:20PM

Program Guide Guide Options Audio & Video Caller ID Program Director WatchWizard Interactive Purchases Lock & Limits View Mail System Setup Watch TV

Button

Buttons

SELECT

System Setup tab.

Direction

SELECT

Button

“Tilt angle” also appears if you have selected an Oval Antenna from the Dish Type menu.

3. Press the front panel

SELECT button.

4. The INSTALL menu helps you to determine the correct antenna position using your 5-digit ZIP code. Enter your ZIP code and press OK.

INSTALLATION

Install Signal Info Features

VCR

Prefs Remote Test New Card

Upgrade Watch TV Main Menu

Dish Pointing

Dish Type

Autoconfig

ZIP Code

2 0 9 0 2

Dish Type: Round Dish

Networks: 0, 3

Switch Type: Simple

LNB: Unstacked

ZIP Code Entry

Wed, Oct 2 12:16PM

Alignment Mode

ZIP Code

Lat/Longitude

Cancel

ZIP Code : Latitude : Longitude :

Elevation : 0 Azimuth : 0

The correct azimuth and elevation angles will appear with onscreen instructions for using these values to properly align your dish antenna.

5. Highlight and

SELECT the Autoconfig menu button to automatically set

your receiver to work with these antenna values.

Getting Started

Testing your system

When you have aligned your dish antenna to the azimuth and elevation angles shown on the

Install pane, highlight the Signal tab. Signal quality is indicated

by a scale at the bottom of the pane and with an audible indication. The frequency and tempo of the tone increase with signal strength.

To perform the Transponder

test:

Use this procedure to test the signal strength from the satellite transponder:

1. Select the

System Setup tab from the MAIN MENU

2. Highlight the Signal tab to display the SIGNAL STRENGTH menu pane.

3. Highlight the Tes t menu button as shown in the figure below.

4. Press

5. Press

SIGNAL STRENGTH

Install Signal Info

Features VCR Prefs Remote Test New card Upgrade Watch TV Main Menu

Xponder

Cursor to the right to activate the

Signal Strength

Source

Satellite 101

Status: Signal Locked

Current: 95 Highest: 98

signal monitor.

SELECT to display the Transponder Test menu (see figure below). SELECT to begin the test on the highlighted selection.

Thu, Oct 3 1:14 PM

)

(A)

Xponder

Test

Note: Xponder and Source selections displayed may vary from those shown.

SIGNAL STRENGTH

Install Signal Info Features VCR Prefs Remote

SIGNAL STRENGTH

Test

Install

New Card

Signal

Upgrade

Info

Watch TV

Features

Main Menu

VCR Prefs Remote Test New Card

Upgrade Watch TV Main Menu

Xponder

916 1724 2532

Signal Strength

Source

TransponderTest

Satellite 101

Satellite 101 (A) Satellite 119 (B) Satellite 110 (C)

Status: Signal Locked

Current: 95 Highest: 95

Satellite 101 (A) Signal Strength

18

94 93 94

Cancel

Signal Strength

Source

Satellite 101)(A)

)

(A) : 5317.6 :0.0.0.75 :OK :OK

94 94 93 95

95 94 93 93

Thu, Oct 3 1:14 PM

Xponder

Test

Thu, Oct 3 1:14 PM

Xponder

Stop

Getting Started

An occasional “0” indication may be considered normal.

Results should generally resemble those in the figure, but the actual values will vary somewhat from those shown in the figure depending on your geographic location and specific installation. However, if your results are very different from these examples (i.e, rows of zeros or single-digit numbers) or you receive no signal indication:

• Highlight the

Install tab on the INSTALLATION menu. Verify your settings.

• Re-enter your ZIP code if necessary to verify you have used the correct antenna pointing parameters for your location.

• Check your cable connections.

• Ensure the DIRECTV

Receiver is connected to a modular telephone jack.

Once you have successfully obtained a signal and your test results resemble those shown in the figures, call DIRECTV (or your subscription service provider) to activate service if you have not already done so.

Getting Started

Adding system components 2

You can configure your DIRECTV® Receiver several ways depending on the additional audio/video components you want to use.

This chapter explains how to:

• Connect a terrestrial (broadcast) TV antenna (this page).

• Connect and set-up a VCR (see page 8).

• Integrate a DIRECTV Receiver into your audio or A/V system (see page 9).

Connecting additional system components

Connecting a terrestrial

antenna/CATV

Connecting a VCR

At this point, you should have:

Verified that your system is operating properly.

Connected your DIRECTV Receiver to your TV.

Unplugged all components from electrical outlets.

You can connect a terrestrial (broadcast) TV antenna or CATV to your DIRECTV Receiver by connecting it to the DIRECTV Receiver’s

ANT/CABLE IN jack (see figures on page 2). The remote control INPUT button

allows you to switch between DIRECTV terrestrial antenna or CATV.

Follow these instructions to connect your TV and VCR to the DIRECTV® Receiver. Connect the satellite antenna RG-6 coaxial cable to the DIRECTV Receiver’s

1. Depending on your VCR, select the appropriate connection to the DIRECTV Receiver:

If your VCR has A/V connectors –

SATELLITE IN jack (see figures on page 2).

• Connect the DIRECTV Receiver’s VCR’s

• If your VCR has only one (mono)

A/V IN jacks.

AUDIO L jack to the VCR’s AUDIO IN jack.

programming and input from the

AUDIO and VIDEO jacks to the

AUDIO IN jack, connect the receiver’s lower

If your VCR only has an RF (coaxial) connector–

• Connect the DIRECTV Receiver’s

VHF/UHF IN or RF IN jack.

2. Depending on your TV and VCR, select the appropriate method to the connect the VCR to the TV:

If your TV and VCR have A/V connectors –

• Connect the DIRECTV Receiver’s corresponding

If your TV or VCR only has an RF (coaxial) jack –

• Connect the VCR’s

3. Plug the TV, VCR, and DIRECTV Receiver power cords into an electrical outlet.

A/V IN jacks on your TV.

VHF/UHF OUT jack to the TV’s VHF/UHF IN jack.

OUT TO TV connector to the VCR’s

AUDIO and VIDEO jacks to the

Adding system components

Connect the VCR Control

Cable

(Model HAH-SA only) The DIRECTV® Receiver can control your VCR for unattended recording, using the VCR Control Cable provided.

1. Plug the VCR control cable into the rear panel

VCR CONTROL jack.

2. Temporarily position the other end over the VCR’s remote control sensor (normally a small dark plastic window on the VCR front panel).

The remote control sensor may be labeled or identified in your VCR manual. If it is not identified, scan the front of the VCR with your VCR remote control:

3. Hold the VCR remote control about ½-inch (1.3 cm) from the front left side.

4. Slowly move the remote control to the right as shown in the figure.

5. Repeatedly press the VCR remote control’s power key on and off.

Scanning for the VCR remote control sensor

6. When your VCR responds to your pressing the remote control power, note the position. Temporarily tape the IR emitter to the position you marked until you verify that it works properly.

Test the VCR (Record/Stop)

This Record/Stop test verifies the specified brand and code controls your VCR.

1. Turn the VCR power on.

2. Insert a recordable videotape into the VCR.

3. Using the satellite receiver front panel buttons, (don’t use the remote control)

4. Highlight and

SELECT the VCR tab from the SYSTEM SETUP menu.

SELECT your VCR brand as shown below.

VCR SETUP

Install Signal Info

Features

VCR

Prefs

Remote

Test

New Card

Upgrade

Watch TV Main Menu

Brand TestCode

Aiwa

Akai Audio Dynamics Bell & Howell Broksonic Canon Capehart

Select Code

Wed, Oct 30 11:53AM

Record

1 2 3 4 5

Stop

Clear

Adding system components

SELECT the highlighted Code menu button.

SELECT the Record menu button under the Tes t column.

7. Verify the VCR is recording.

SELECT the Stop menu button.

If either command does not function, try other codes listed for your VCR brand. If you are unsuccessful after trying all available codes, recheck your VCR Control Cable connections and IR emitter placement.

9. Remove the temporary mounting tape. Attach the emitter permanently using the peel-and-stick backing. This will not interfere with normal VCR operation.

Connecting a home

entertainment system

The A/V receiver must be turned on in order to send the video and video signal to your TV.

You can integrate the DIRECTV® Receiver into your entertainment system to take advantage of enhanced audio and video capability. Follow these instructions to connect your DIRECTV Receiver.

• To connect the DIRECTV Receiver to your audio system, use A/V cables to connect the satellite receiver to the audio receiver’s

AUDIO IN jacks.

• Dolby Digital - With the HAH-SA satellite receiver, you can enjoy programs that contain a Dolby Digital sound track. We recommend that you listen in surround sound for maximum enjoyment of these programs. You can connect the stereo outputs of the HAH-SA to a receiver that contains a Dolby Surround Pro Logic decoder. This will provide you with three audio channels in the front and a mono surround channel.

• To take full advantage of Dolby Digital programming, connect the HAH-SA digital audio output to an external 5.1-channel Dolby Digital decoder or receiver. This provides you with three front channels, two independent surround channels, and an LFE (or subwoofer) channel.

1. Connect the satellite antenna RG-6 coaxial cable to the DIRECTV Receiver’s

2. Connect the DIRECTV Receiver’s

A/V jacks.

SATELLITE IN jack.

A/V jacks to the VCR and A/V receiver’s

3. AUX, optical connection, and digital output connections – If your audio receiver has optical digital connectors, connect the appropriate type of cable to the DIRECTV Receiver’s

DIGITAL AUDIO OUT for two-channel digital

stereo. If your A/V receiver is also capable of decoding Dolby Digital, use this connection in order to listen in full 5.1-channel surround sound. Refer to page 25 for additional audio information.

4. Connect the VCR’s

A/V OUT jacks to a pair of the A/V receiver’s A/V IN

jacks.

5. Connect the A/V receiver’s

MONITOR OUT jack to the TV’s VIDEO IN

jack.

6. Plug the components into an electrical outlet.

Note: If you have connected a VCR to your entertainment system in a way that routes the satellite receiver’s signal to your VCR before it reaches the TV, you may see a distorted picture if you try to record (or view in some instances) a copy-protected program. A banner identifies these programs.

Can’t Tape

Adding system components

symbol in the screen

+ 39 hidden pages