Direct IP IDIS DR-1304P, IDIS DR-1308P, IDIS DR-1304PC Operation Manual
Network
Video
Recorder
Operation Manual
DR-1304P
DR-1308P
DR-1304PC
Powered by
Before reading this manual
This operation manual contains basic instructions on installing and using DirectIP™ Network Video Recorder, an
IDIS product. Users who are using this product for the rst time, as well as users with experience using comparable
products, must read this operation manual carefully before use and heed to the warnings and precautions contained
herein while using the product. Safety warnings and precautions contained in this operation manual are intended to
promote proper use of the product and thereby prevent accidents and property damage and must be followed at all
times. Once you have read this operation manual, keep it at an easily accessible location for future reference.
• The manufacturer will not be held responsible for any product damage resulting from the use of unauthorized parts and
accessories or from the user's failure to comply with the instructions contained in this operation manual.
• It is recommended that rst-time users of DirectIP™ Network Video Recorder and individuals who are not familiar with its
use seek technical assistance from their retailer regarding product installation and use.
• If you need to disassemble the product for functionality expansion or repair purposes, you must contact your retailer and
seek professional assistance.
• Both retailers and users should be aware that this product has been certied as being electromagnetically compatible for
commercial use. If you have sold or purchased this product unintentionally, please replace with a consumer version.
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the product’s enclosure that may be of sucient magnitude to
constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Symbol Publication Description
IEC60417, No.5032 Alternating current
IEC60417, No.5031 Direct current
WARNING
Hazardous moving parts
Keep away from moving fan blades
AVERTISSEMENT
Pièces mobiles dangereuses
Se tenir éloigné des pales de ventilateurs mobiles
2
Before reading this manual
1. Read Instructions
All the safety and operating instructions should be read before the appliance
is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future reference.
3. Cleaning
Unplug this equipment from the wall outlet before cleaning it. Do not use
liquid aerosol cleaners. Use a damp soft cloth for cleaning.
4. Attachments
Never add any attachments and/or equipment without the approval of the
manufacturer as such additions may result in the risk of re, electric shock or
other personal injury.
5. Water and/or Moisture
Do not use this equipment near water or in contact with water.
6. Ventilation
Place this equipment only in an upright position. This equipment has an
open-frame Switching Mode Power Supply (SMPS), which can cause a re or
electric shock if anything is inserted through the ventilation holes on the side
of the equipment.
7. Accessories
Do not place this equipment on an unstable cart, stand or table. The
equipment may fall, causing serious injury to a child or adult, and serious
damage to the equipment. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit approved by the
manufacturer.
This equipment and cart combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may cause the equipment and cart
combination to overturn.
8. Power Sources
This equipment should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power, please
consult your equipment dealer or local power company. You may want to
install a UPS (Uninterruptible Power Supply) system for safe operation in order
to prevent damage caused by an unexpected power stoppage. Any questions
concerning UPS, consult your UPS retailer.
This equipment should be remain readily operable.
9. Power Cords
Operator or installer must remove power and TNT connections before
handling the equipment.
10. Lightning
For added protection for this equipment during a lightning storm, or when it
is left unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will prevent damage
to the equipment due to lightning and power-line surges.
11. Overloading
Do not overload wall outlets and extension cords as this can result in the risk
of re or electric shock.
12. Objects and Liquids
Never push objects of any kind through openings of this equipment as they
may touch dangerous voltage points or short out parts that could result in a
re or electric shock. Never spill liquid of any kind on the equipment.
13. Servicing
Do not attempt to service this equipment yourself. Refer all servicing to
qualied service personnel.
14. Damage requiring Service
Unplug this equipment from the wall outlet and refer servicing to qualied
service personnel under the following conditions:
A. When the power-supply cord or the plug has been damaged.
B. If liquid is spilled, or objects have fallen into the equipment.
C. If the equipment has been exposed to rain or water.
D. If the equipment does not operate normally by following the operating
instructions, adjust only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualied technician to
restore the equipment to its normal operation.
E. If the equipment has been dropped, or the cabinet damaged.
F. When the equipment exhibits a distinct change in performance − this
indicates a need for service.
15. Replacement Parts
When replacement parts are required, be sure the service technician has
used replacement parts specied by the manufacturer or that have the same
characteristics as the original part. Unauthorized substitutions may result in
re, electric shock or other hazards.
16. Safety Check
Upon completion of any service or repairs to this equipment, ask the service
technician to perform safety checks to determine that the equipment is in
proper operating condition.
17. Field Installation
This installation should be made by a qualied service person and should
conform to all local codes.
18. Correct Batteries
Warning: Risk of explosion if battery is replaced by an incorrect type. Replace
only with the same or equivalent type. Dispose of used batteries according to
the instructions. The battery shall not be exposed to excessive heat such as
sunshine, re or the like.
Avertissement: risque d'explosion en cas d'utilisation d'une batterie de type
incorrect. Le remplacer uniquement par un type identique ou équivalent.
Mettre les batteries usées au rebut conformément aux instructions. La batterie
ne doit pas être exposée à une source de chaleur excessive, telle que le soleil,
le feu, ou analogue.
19. Tmra
A manufacturer’s maximum recommended ambient temperature (Tmra)
for the equipment must be specied so that the customer and installer may
determine a suitable maximum operating environment for the equipment.
20. Elevated Operating Ambient Temperature
If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient
temperature (Tmra).
21. Reduced Air Flow
Installation of the equipment in the rack should be such that the amount of
airow required for safe operation of the equipment is not compromised.
22. Mechanical Loading
Mounting of the equipment in the rack should be such that a hazardous
condition is not caused by uneven mechanical loading.
23. Circuit Overloading
Consideration should be given to connection of the equipment to supply
circuit and the eect that overloading of circuits might have on over current
protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
24. Reliable Earthing (Grounding)
Reliable grounding of rack mounted equipment should be maintained.
Particular attention should be given to supply connections other than direct
connections to the branch circuit (e.g., use of power strips).
HDMI Port Precautions
• Use a certied cable marked with an HDMI logo when using HDMI.
The screen may not display or a connection error may occur if you do
not use a certied HDMI cable.
• It is recommended that you use the following HDMI cable type.
– High-speed HDMI Cable
– High-speed HDMI Cable with Ethernet
3
Before reading this manual
Important Safeguards
In-Text
Symbol Type Description
Caution Important information concerning a specic function.
Note Useful information concerning a specic function.
User’s Caution Statement
Caution: Any changes or modications to the equipment not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
FCC Compliance Statement
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART
15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE
WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE
RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE
HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO
CAUSE HARMFUL INTERFERENCE, IN WHICH CASE USERS WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT THEIR OWN EXPENSE.
WARNING: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID
THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
THIS CLASS OF DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE CAUSING EQUIPMENT
REGULATIONS.
WEEE (Waste Electrical & Electronic Equipment)
Correct Disposal of This Product
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
oce, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This
product should not be mixed with other commercial wastes for disposal.
4
Before reading this manual
Copyright
© 2018 IDIS Co., Ltd.
IDIS Co., Ltd. reserves all rights concerning this operation manual.
Use or duplication of this operation manual in part or whole without the prior consent of IDIS Co., Ltd. is strictly
prohibited.
Contents of this operation manual are subject to change without prior notice.
Registered Trademarks
IDIS is a registered trademark of IDIS Co., Ltd.
Other company and product names are registered trademarks of their respective owners.
The information in this manual is believed to be accurate as of the date of publication even though explanations of some
functions may not be included. We are not responsible for any problems resulting from the use thereof. The information
contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate
such changes.
The software included in this product contains some Open Sources. You may obtain the complete corresponding source code
depending on whether or not the source is publicly available under a license policy. Go to System Setup - About page for
more information. This product includes software developed by the University of California, Berkeley and its contributors, and
software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.oepnssl.org/). Also, this product includes
cryptographic software written by Eric Young (eay@cryptsoft.com), and software written by Tim Hudson (tjh@cryptsoft.com).
5
Table of Contents
Part 1 - Getting Started .....................................10
1
Setting Password ...............................................................10
Setup Wizard ...................................................................10
Camera Registration ............................................................14
Camera Scan Button ......................................................................15
Camera View Buttons .....................................................................18
Camera List Area .........................................................................19
Video Display Area .......................................................................19
Apply/Cancel Buttons ....................................................................20
Diagnosis Process ........................................................................21
Camera Registration Mode ......................................................21
Login ..........................................................................22
Live Menu ...............................................................................24
Zoom ....................................................................................26
PTZ Control ..............................................................................26
Dewarping Control (Camera) .............................................................28
Event Monitoring ........................................................................28
Covert Camera ...........................................................................28
Context Menu Access ....................................................................28
Edit Group ...............................................................................29
2
6
Video Recording ................................................................29
Panic Recording ..........................................................................29
Video Recording Playback ......................................................29
All Channel Playback .....................................................................29
Part 2 - Conguration .......................................30
Menu Use ......................................................................30
Tex t Input via Virtual Keyboard ...........................................................30
Batch Assignment ........................................................................31
Mouse ...................................................................................31
System Setup ..................................................................31
General ..................................................................................31
Date/Time ...............................................................................33
User .....................................................................................34
Security ..................................................................................36
Storage ..................................................................................37
Self-Diagnosis ............................................................................37
About ....................................................................................38
Camera Setup ..................................................................39
Registration ..............................................................................39
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Advanced Setup .........................................................................41
Stream I ..................................................................................47
Stream II .................................................................................48
Upgrade .................................................................................49
Record Setup ...................................................................49
General ..................................................................................49
Schedule .................................................................................50
Pre-Event ................................................................................52
Event Setup ..............................................................................52
System_Event ............................................................................52
Camera System ..........................................................................53
Camera System_Video Loss ...............................................................54
Camera System_Recording Fail ...........................................................54
Video-Analytics ..........................................................................55
Video-Analytics_Motion ..................................................................55
Video-Analytics_Trip Zone ................................................................57
Video-Analytics_Tampering ..............................................................58
Network Setup .................................................................59
General ..................................................................................59
WLDLWAN ...............................................................................59
FEN ......................................................................................61
Firewall ..................................................................................62
Notication Setup ..............................................................62
Schedule .................................................................................62
Callback .................................................................................63
Mail ......................................................................................63
Push .....................................................................................64
Display Setup ..................................................................65
OSD .....................................................................................65
7
Main Monitor ............................................................................65
Status Setup ...................................................................66
Camera ..................................................................................66
Device ...................................................................................66
System ...................................................................................67
Storage ..................................................................................67
Network .................................................................................68
Part 3 - Search ..............................................70
3
Time-Lapse Search .............................................................70
Search Menu .............................................................................70
Context Menu ............................................................................72
Motion Search ...........................................................................72
Clip Copy ................................................................................73
Event Log Search ...............................................................74
Overlapped Recording Search ..................................................75
Memo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
8
Part 1 - Getting Started
This document covers the 4- and 8- channel
network video recorders. The NVRs are identical
except for the number of cameras and alarms
that can be connected and the number of
cameras that can be displayed. For simplicity, the
illustrations and descriptions in this document
refer to the 4-channel model.
Setting Password
The users must rst run the system and then be
1
required to set the password for the admin user
account.
Setup Wizard
Setup Wizard lets you congure basic settings required
for operating the system.
Setup Wizard only appears during initial booting.
When you login as an administrator account after
initial booting, you can use Wizard to go to Live menu
and select Wizard.
Select a system language.
1
• It does not allow a user to run the system
without a password.
• Click the question mark button on the bottom
left corner and refer to the instruction on
setting up a password.
• An email address and UPR les are required to
nd the password. Otherwise, you may not be
able to nd your password when you enter the
incorrect information.
Select Cancel from any of the Wizard screen to
cancel the setup process and return to the main
setup menu.
9
Part 1 - Getting Started
Quick Wizard
Select Quick Wizard.
1
Specify the current date and time and then click
2
Next.
Choose the desired Recording Method and click
3
Next.
Choose the desired Recording Quality and click
4
Next.
10
•The new date and time settings will only be
applied after clicking Next.
•For more information on date and time
settings, refer to the Date/Time section under
System Setup on page 30.
•Higher recording quality uses up more disk
space.
•Recording resolution is determined based on
the selected recording quality.
– High Video Quality Priority Prole: Very
high
– Standard Recording Prole: High
– Longer Recording Time Priority Prole:
Standard
Part 1 - Getting Started
– Recording resolutions used under each recording method
and record video quality setting are as follows:
High Video Quality
Priority Prole
Motion
Event
Record
Continuous
& Motion
Event
Record
Continuous Very high High Low
Choose the desired codec and click Next.
5
Very high High Standard
High (Continuous) /
Very high (Motion)
Standard
Recording
Prole
Standard
(Continuous) /
High (Motion)
Longer Recording
Time Priority
Prole
Low (Continuous) /
Standard (Motion)
Network Wizard
After exiting from Quick Wizard, the network with
Network Wizard will start automatically.
Select Network Wizard.
1
Specify whether the system is connected to the
2
Internet and click Next.
Click Finish to exit Quick Wizard.
6
If you have chosen No, wait for the test to nish
and then click Finish to exit Network Wizard.
11
Part 1 - Getting Started
Select Network Conguration and then click
3
Next. Select either Auto Conguration or Manual
Conguration and then click Test to test the system’s
current network conguration.
•This test must be performed before proceeding
to the next step.
•If the NVR is on a network connected to a
network that has a DHCP server, selecting Auto
Conguration retrieves LAN settings such as
IP and DNS addresses automatically. Selecting
Manual Conguration, on the other hand, lets
you specify the settings manually.
•UPnP support device not found. If this error
message is displayed, check to see if the IP
router (or NAT) supports UPnP and if UPnP has
been enabled. For more information about the
router's UPnP function, refer to the router's
operation manual.
Enter in the Device Name eld the NVR name to be
4
registered on the FEN server and then click Check to
check its availability.
•The device name you register on the FEN server
will be a unique name used to identify the
NVR. Once registered, the name can be used
to access the NVR directly from clients such as
the IDIS Center. Check the name's availability
to complete the registration process. The Finish
button will then become activated.
•You will be prompted with an error message if
you do not enter a name for the NVR or enter a
name already registered on the FEN server.
•Depending on the network environment,
FEN services may not be active and therefore
prevent the NVR from connecting to the
network. In this case, you will need to manually
congure the ports. For more information on
port conguration, refer to Network Setup on
page 58.
12
Click Finish to exit Network Wizard.
5
Part 1 - Getting Started
Camera Registration
Once Network Setup Wizard is complete, live mode
screen appears. While in live mode, right-click on the
mouse and select Camera Registration to run the
Camera Registration mode. It allows you to scan for the
cameras connected to the NVR.
1
3
4
5
1
2
3
4
5
Camera Scan Button
Camera View Menus
Camera List Area
Video Display Area
Apply/Cancel Buttons
You can also register cameras on the remote
program. For more information on the remote camera
registration, refer to Registration on page 13.
2
13
Part 1 - Getting Started
Camera Scan Button
You can scan and search and register cameras that were
not detected automatically or third party cameras.
Pressing the Scan button displays the following submenu.
Rescan
Scans for DirectIP™ cameras that were not scanned
automatically.
Third Party Scan
Scans for IDIS Open cameras that do not support
automatic scan feature.
● Mode: Select the scan mode.
– Auto Scan (LAN): Lists cameras in a LAN
environment. If Auto Scan (LAN) fails to recognize
a camera, try using IP Address Scan instead.
– IP Address Scan: Enter the IP address of a
camera. The NVR scans for the camera matching
the specied address. If you enter IP address’s
range, the NVR scans for cameras falling under
the specied address’s range. By specifying an IP
address, you can also specify which port to use with
the Remote Admin feature. It is recommended that
the camera not be networked via DHCP (Dynamic
Host Conguration Protocol). If the camera is
networked via DHCP, connection to the camera may
not be made properly depending on changes in the
external network environment.
● Advanced Setup: If the camera is networked but
not scanned, use this setup. This setup allows you to
change the network setting of the NVR’s VIDEO IN
port which is camera’s network environment. Check
the camera’s network setting rst before you use this
setup.
Make sure that this setting does not conict with
the WAN setting. For more information on the
WAN setting, refer to WLDLWAN on page 58.
● Protocol: Select the protocol used by the camera (or
video encoder) you wish to search for.
• Some functions may not be supported for the
third-party cameras depending on their protocol
and model.
14
– Link-local address: Indicates the default IP
address.
Part 1 - Getting Started
the same network. If there is no DHCP server,
this option is enabled. The NVR allocates an IP
address automatically in the range of 10.10.0.128
to 10.10.254.254 by using DHCP to the camera
connected to the NVR’s VIDEO IN port. On DHCP
Server, Video In Network is connected between
NVR and network cameras only, so Gateway
does not have any meaning. Subnet Mask is
255.255.0.0(Class B).
– Manual: Allows you to enter the IP address and
other network settings manually.
– DHCP Client: Retrieves an IP address and other
network settings automatically from a DHCP server.
•When several NVRs exist in the same network,
only one of NVRs has to be run as a DHCP
server. If several DHCP servers are running, the
redundant IP may be allocated to the camera.
•The range of 10.10.0.1 to 10.10.0.127 is not
recommened because NVR system already has
the IP address.
– DHCP Server: It makes the NVR run as a DHCP
server. Check if there is another DHCP server on
15
Part 1 - Getting Started
Select Scan to commence scanning.
1
Only cameras that are connected to the NVR via VIDEO
IN ports can be scanned and registered.
Select a camera from the scan list and then select
2
Add Camera. The device login window will appear.
Enter a User ID and a Password for the selected
3
camera.
Go To Camera
Moves the focus automatically to the camera using the
MAC addressa and model of camera in the camera list.
Camera list
By using the camera information le, .csv, the user can
register the cameras easily.
● Export : Button : Exports the list of camera
information on USB as a .csv le
● Import : Button : Imports a camera information le,
.csv le. The user can edit a csv le directly.
•A column indicates camera number, B
column the camera MAC address, C column
the Video In port of the video encoder in the
.csv le. C column indicates only for video
encoders. If camera information displays
as follows: 5,00:11:22:18:30:20,3, 5 = CAM 5,
5,00:11:22:18:30:20 = MAC address, 3 means video
encoder.
•Before using this feature, the cameras must be
scanned rst. If the cameras to be registered
do not exist in the list, the camera cannot be
registered.
•This feature is not supported for the third-party
cameras.
Search Scope
Filters the cameras in the camera list depending on the
search scope such as specied IP address range.
Screen Auto. Assign
Assigns the detected cameras on the video display area.
16
Scan Refresh Interval
Congures the refresh interval to scan the camera. If
the interval is short, camera scan results are refreshed
more frequently. However, if the interval is long, it is
advantageous to scan cameras on a wide network.
Part 1 - Getting Started
Camera View Buttons
● ALIGNMENT Button: Realigns camera screens
displayed on the video display area in the order of
Video In port connections.
● RESET
and the camera list.
● Bitrate Button: Displays the following window to
change the bitrate allocation for each channel.
When registering the camera, you can set the stream
as much as the performance (bitrate) assigned to the
channel. If high performance (bitrate) is not allocated,
Quailty, IPS and Resolution can be low. If a channel
has a camera already registered, bitrates may not be
lower than current stream settings. When selecting
default, performance is evenly assigned to each
channel. If a channel has a camera already registered,
the minimum value is assigned.
● Tool
window to run a camera-related actions. There are
Authentication, Screen Assignment and Camera
Protocol Change for actions.
Button: Refreshes the video display area
Selecting RESET clears all scanned devices from the
list.
Button: Displays network camera tool
IDIS cameras can be detected automatically but
IDIS protocol cannot be detected automatically.
We recommend you use the DirectIP protocol
to detect the cameras automatically. When you
change the protocol, the camera reboots and then
you can register the camera on the NVR. For more
information on the settings, please refer to the
network camera manual.
Select an Action to execute.
1
Select a camera from the list and press the Apply
2
button.
17
Part 1 - Getting Started
Camera List Area
2
1
Registered
Registered
Registered
Initial registration
other NVRs
(Registration X)
1 Screen Position/Registration Status: Identies the
camera’s position in the video display area. A blue
background indicates a camera that is available for
registration. A gray background indicates an already
registered camera. Other registered cameras are
shown in black background.
3
4
Video Display Area
Left-click on the video display area to toggle between
split screen and single screen modes.
Drag the camera screens around to rearrange them.
Camera Screen
1
2 3
1 Camera Title
Indicates the camera’s title. Left-click on the title to
edit the camera’s title.
4
2 Model: Indicates the camera’s model.
3 MAC: Displays the 12 digits of the camera’s MAC
address.
4 Title: Indicates the camera’s name. Changing a
camera’s name in the video display area updates the
camera list as well.
Following options can be accessed by right-clicking on a
camera list entry:
● Add/Remove Camera: Adds or removes the selected
camera. The Add Camera option is inactive if the
camera has already been added to the screen.
● Authentication: Enter the necessary camera login
info. This option is inactive for DirectIP™ / IDIS cameras
because they do not require logins. This option is
inactive for IDIS protocol only if the password is set.
18
2 MAC Address
Camera’s model and MAC address are shown if the
camera has not been registered to the NVR.
3 Screen Position/Registration Info
Flashes in orange if the camera has not been
registered to the NVR.
Part 1 - Getting Started
•Information is not indicated on the bottom of the
screen for cameras already registered to the NVR,
and the Screen Position/Registration Info icon is
shown with a black background.
•Screen Position/Registration Info icon for cameras
registered to another NVR is shown with a steady
orange background on top of a gray screen.
4 Bitrate Allocation
Indicates the performance (bitrate) allocated to the
channel. Left-click on the upper right corner of the
screen to change the bitrate.
Camera Menu
Right-click on the video display area to bring up the
camera menu.
Apply/Cancel Buttons
While in Camera Registration mode, select Apply
to register all changes. When selecting Apply, the
following message will be displayed. You can activate or
deactivate Self-diagnosis.
Select Cancel to exit Camera Registration mode without
applying the changes.
It is not possible to register a camera that has already
been registered to a dierent NVR.
● Remove Camera: Removes the registered camera.
● Remove Device: Removes the registered encoder.
● Color Control: Adjusts the camera’s color settings.
● Information: Displays the camera’s basic information.
● Title: Edits the camera’s title.
● Bitrates: Changes the bitrate allocated to the channel.
● Remove All Cameras: Removes all registered
cameras.
You can drag & drop to add or remove cameras.
19
Part 1 - Getting Started
Diagnosis Process
When the camera is registered to the NVR, Selfdiagnosis runs automatically for the new registered
and changed cameras. If Self-diagnosis is processing,
Diagnosis Processing message will be displayed.
If Self-diagnosis is failed, Diagnosis Requirement
message will be displayed. In this case, you can run Self-
diagnosis manually.
Camera Registration Mode
While in Live mode, right-click and select Camera
Registration.
20
Part 1 - Getting Started
Login
Conguring the NVR’s settings and accessing its
searching and other functions require an authorized
user login.
Bring up the Live menu and click on (Login) using
1
the mouse.
Select a user, enter the password, and then select
2
OK.
•There is no default password for the admin
account. Select admin and then OK without
entering a password to log in.
•Leaving the admin account unassigned with
a password poses a security risk. Please assign
a password at your earliest convenience. A
warning message will continue to be displayed
until a password is assigned.
•Click on the
eld using the mouse. This will bring up a virtual
keyboard you can use to assign a password. For
more information on using the virtual keyboard,
refer to the Text Input via Virtual Keyboard on
page 29.
To log out, bring up the Live menu and click on
3
(Log out) using the mouse.
button next to the password
Find Password
If you do not know the password, select FIND PW . You
can set a new password.
Enter a user, registered email and then select Get
1
Verication Code.
Enter Verication Code and select OK.
2
•Select the question mark button at the bottom
left corner of the screen to refer to the password
settings instructions.
•The password must be entered only with the
virtual keyboard.
•To use nd password function via e-mail, set
the mail server supporting SSL/TLS. For more
information on e-mail, refer to Mail on page
62 and SMTP Setup on page 63.
21
Part 1 - Getting Started
Enter an UPR(User Password Reset) verication and
3
then click on UPR Verication button.
Select the UPR le and then click on Import button.
4
•To use UPR function, the UPR le must be saved
in advance. For more information on saving the
UPR le, refer to User on page 33.
•You can reset the password using an encrypted
UPR (User Password Reset; lename extension *
.upr) le.
•It can be used as USB ash driver on local pc,
but not remotely.
•Only les exported from the same device are
available.
•If you lose the UPR le and change the password
of the NVR, the UPR le may not be used.
22
Live Mode
Live Menu
Placing the mouse pointer near the top portion of the screen displays the Live menu.
Part 1 - Getting Started
4
3
Layout
Panic Recording
Setup
5
6
7
9
8
Previous Group,
3
Next Group
Sequence
7
Wizard
!
0
!
Display
4
Select Camera
8
Status Indication
@
1
5
9
1
Login/Logout
Freeze
Search Mode
2
2
6
0
1 Login/Logout
Log into and out from accounts. If in the logged in state, the account ID is shown. If in the logged out state, the
login icon is shown.
2 Layout
Used to change the screen layout to single screen, 1x2, corridor format(1x3), 2x2,1+5, 1+7 or 3x3.
• Corridor Format: Divides the screen into 3 panes. This format displays vertically and is set to display the
optimized video of the camera when using the camera’s pivot feature. This is particularly eective when
monitoring hallways, passages, and other conned spaces.
• 1+5, 1+7 and 3x3 screen format are supported only on 8-channel model.
3 Previous/Next Group
Loads the previous/next screen group.
@
4 Display
●OSD (On Screen Display): Enables/disables the OSD feature.
●Full: Displays the video in full screen mode.
●Aspect Ratio: Select whether to enable the original aspect ratio of video transmitted from the camera.
5 Freeze
Freezes the screen. Select Freeze again to unfreeze.
6 Panic Recording
Activates/deactivates Panic Recording.
7 Sequence
Selecting the Sequence icon
while in Live mode changes to the sequence mode. To exit, select Sequence icon
once more. The icon is displayed on the upper right part of the screen while Sequence is in progress.
23
Loading...